User Manual User Manual
Contents
1. and Avantco is not responsible for any warranty claims made on products sold or used outside of the United States www AvantcoEquipment com 192. approximately 45 minutes Cabinet temperature reaches 185 85C within approximately 45 minutes 5 Re set TEMPERATURE control and adjust as necessary to reach desired temperature setting 6 8 is typical for 150 66C to 160 71C PROOFING INSTRUCTIONS 2 0 4 KANTCO 1 Set Combination Module switch to PROOF 2 Set POWER switch to the ON position Power indicator light will turn on 3 Set TEMPERATURE control to 2 4 Set HUMIDITY control to 9 5 Pre heat cabinet until desired temperature and humidity is reached typical heat up time from 77 25C ambient to 95 35C and 95 relative humidity is approximately 30 minutes 6 Adjust settings as necessary to reach desired temperature and humidity levels NOTE The internal air circulation blower and 1500W heater element controlled with the Heat Thermostat will operate continuously when the power switch is turned ON www AvantcoEquipment com 5 EQUIPMENT User Manual VANTCO HEAT THERMOSTAT The controlling range is 80 F to 185 F The dial numbers 1 thru 9 do not relate to a specific calibrated temperature Temperature settings must be obtained through familiarization with the unit The dial also has an OFF position to turn heater unit off HUMIDITY THERMOSTAT To control humidity range from 30 to 100 humidity settings must be obtained through familiarization with the unit The dial numbers 1 thru 9 do not relate to a specific calibrated humidity The di
3. 111 3915 11150041 1 3 EMAYE A To e PLA 239 801291002092 pi 1 Bed 5 www AvantcoEquipment com 18 EQUIPMENT VANTCO User Manual Troubleshooting CAUTION Before disassembling unit electrical power must be disconnected by unplugging the unit Failure to unplug the unit prior to servicing may result in electrical shock Each unit is shipped with this instruction manual and should be used as a reference guide for all service areas The manual provides a picture of the drawer showing the location of electrical components and a description of each If the unit does not operate correctly or malfunctions for any reason the following check list should provide a solution 1 Check to make sure power cord is firmly plugged into the wall outlet 2 Check circuit breaker of wall outlet and reset if necessary IF unit fails to start please do the following 3 Remove heat drawer from cabinet Remove bottom cover of drawer Visually inspect to observe for a Loose or disconnected wires b Black or burnt marks on any components c Loose heating elements 4 If any burn marks or discoloration of wires is noted on any component the component along with all wires attached to the damaged component must be replaced 5 If a heater element is loose or if it has broken loose from mounting tabs the wires will sh
4. EQUIPMENT VANTCO User Manual Heater Proofer Cabinets Models 177 836 177 812 177HPI1836 177HPU1812 177HPU1836 08 2015 Please read and keep these instructions Indoor use www AvantcoEquipment com 1 EQUIPMENT User Manual VANTCO Index General Information vc duds 4 5 0 EK O la 4 MaINIENANCE asa R ee 4 Operating 0 5 w 1 1 1 1 1 1 a 5 gt 19 116 1 0 11119 111911 ii 6 Recommended Temperature Guidelines Food Holding Chart 7 Drawer ASSEMDIYV aia kia ad ak 8 0 Cabinet Assembly 3 5 kn 11 6 Electric Schematic Power Supply 17 18 TFOUDIESNOOUNG ee 19 SAFETY INFORMATION WARNING Follow all food safety guidelines Pre heat the cabinet to the desired temperature before placing cooked hot food into the cabinet This is not a re thermalizing cabinet Food must be at the appropriate temperature before being placed in to this cabinet Use a food probe to check internal food temperature the cabinet temperature is not necessarily the internal food temperature WARNING Only factory approved service agents should attempt to service repair or replace electrical components wiring or power cord WARNING Unplug the cabinet before cle
5. Magnetic Strip Include top 1pc 177HEATI1836 177HPU1812 177HPI1812 177HEAT1812 177HEATI1812 177HPU1836 177HPI1836 Right Left side 2pcs 177HEAT1836 177HEATI1836 Door Assembly 177HPU1812 177HPI1812 177HEAT1812 177HEATI1812 1 6 16 177HEA 1836 na Bumper 4 JA 177HEATI1836 16 177HPI1836 177HPU1812 177HPI1812 HC1812HP 06 HC1836HP 06 Door Assembly HC1836HP 07 HCD1500 Heat proof drawer HCD1500H Only Heat drawer 177HEAT 1836 177HEATI1836 177HEAT1812 177HEATI1812 www AvantcoEquipment com 13 Plastic Pan Black 5 Caster with Brake Include Hardware Plastic Pan Caster HC1836HP 029 Bumper 16 5 lt U i 7 gt i I 82384 pe HOLS BULL 25 SOLA L J 852080290091 8 Fr NEM 1 1 150018 tH mom 038 Ji a T 0 gt mon mon OO 1 EY 1400 03 I LL quem 5 38 0 75 881 HOLIINNOS LL weromiss oi 51 WAM 31832 SZAH L oz 1 150 3 p n HEAT PROOF Models HCD1500 Drawer HILME 216 Electric Schematic Power Supply EQUIPMENT VANTCO 17 www AvantcoEquipment com EQUIPMENT VANTCO G lt U i 7 gt HEAT Models HCD1500H Drawer Onl gt 11 06 C 1 2 2 70 40012
6. Part No HCD1500H Rated Power 1500 W 120V 60HZ CAUTION If any damage is found do not attempt to operate the unit Call your dealer IMMEDIATELY to arrange for service www AvantcoEquipment com 3 EQUIPMENT User Manual VANTCO Installation Position your unit on a stable level surface and plug in the supplied cord into any grounded 120 Volt AC 15 amps power supply dedicated breaker It is highly recommended that you use ONLY the power cord supplied Use of a dedicated circuit will help to insure operational efficiency Do not operate the unit with an extension cord 15Amp Outlet For Cabinet rated 120V 1500Watt Maintenance The equipment has been designed to require minimum maintenance and has been constructed to meet National Sanitation Foundation and U S Public Health Service standards Non toxic chemical cleaners or mild detergents are recommended for cleaning of fixtures DO NOT use steel wools of any kind Steel wool particles will work into the grains of the metal causing corrosion Also these particles can cause a health hazard If scouring is required use a non abrasive type of cleaner Do not use caustic solutions on your equipment Hosing or steam cleaning should not be necessary to keep these fixtures clean and sanitary Do not allow water or steam to come into contact with electrical components Never power wash or steam clean the cabinet with the electrical cord plugged in CAUTION Be sure to disconnect power sour
7. al also has an OFF position to turn humidity off To maintain low heat range between 85 F to 100 F switch to proof mode and adjust heat knob to desired heat range Allow 45 minutes to pre heat in proof cycle Service Specifications The Heater Proofer is an aluminum transport cabinet with heaters to function as a hot food holding cabinet and or as a proofing cabinet The heater or heat drawer is slid into place on the lower ledges of the cabinet An electrical power cord is provided and plugged into the drawer through an access hole in the back of the cabinet The main power switch on the front of the drawer when switched ON will turn on the light in the switch and turn on the air circulating fan in the drawer The circulating fan and 1500W heater element will operate continuously while the unit is ON The thermostat control knobs are mounted to the left and right of the HEAT PROOF switch The left thermostat knob controls the heat in the cabinet from 1 approx 30 relative humidity to 9 100 relative humidity Average setting is 6 approx 85 relative humidity 6 www AvantcoEquipment com EQUIPMENT VANTCO User Manual Recommended Temperature Guidelines Food Holding Chart Baked Fish Uncovered 175 F 79 C Baked Potatoes Uncovered 180 F 82 C Biscuit Covered 180 F 82 C Broccoli Uncovered 170 175 F 77 79 C Chicken Nuggets Covered 175 F 79 C Corn on the Cob Uncovered 170 175 F 77 79 C Croissants Co
8. aning or servicing Do not wash the cabinet with a water jet or high pressure water WARNING This cabinet is for hot food holding applications only CAUTION Do not spray or pour water into the module To clean the cabinet wipe with a damp cloth and dry with a towel Use only cleaning agents approved for aluminum CAUTION Water dripping onto the floor from open doors can be a slip hazard 2 www AvantcoEquipment com EQUIPMENT VANTCO User Manual General Information The models For example 177 HEAT 18 36 HEATED CABINETS LL PAN QTY 36 PCS 177 1 2 2 4 C 5 Series ONLY HEAT PAN WIDTH 18 NO PROOF NO INSULATE 1 HEAT HEAT Only Heat or H Commonly Used 2 PROOF P For example 177HP118 12 me HEATED CABINETS L PAN QTY 12 PCS MANET M HEAT PAN WIDTH 18 4 For example 18 PROOF WITH INSULATE 5 PAN QTY From 12 to 36 HEATED CABINETS L PAN QTY 36 PCS HEAT PAN WIDTH 18 PROOF WITH INSULATE For example 177 H P U 18 12 HEATED CABINETS L PAN QTY 12 PCS HEAT PAN WIDTH 18 PROOF NO INSULATE For example 177 H P U 18 36 HEATED CABINETS L PAN QTY 36 PCS HEAT PAN WIDTH 18 PROOF NO INSULATE The cabinet will hold food hot at a constant temperature and supply humidity for proofing when the application applies This cabinet is NOT a cooking appliance Heat Unit Specifications Removable bottom mount proof heat unit Part No HCD1500 or only heat unit
9. ce before cleaning and servicing the unit Liability for improper or careless use is the responsibility of the equipment owner or persons Servicing the unit including the authorized service agent ye STRIKE Attack tough grease oil and carbon with this ready to use cleaner and NOBLE degreaser lts unique formula is designed to clean concrete machinery Cleaner Degroasor engines floors walls and more 4 www AvantcoEquipment com EQUIPMENT VANTCO User Manual Operating Instructions A Refer to DATA PLATE for electrical requirements Cabinets rated at 120V 1500 watts must be plugged into a 125 VAC 15 amp receptacle and must be used on an individual branch circuit DO NOT MODIFY CORD PLUG B With POWER switch OFF plug into 125 VAC grounded receptacle C Fill water pan to top with clean HOT tap water for Proofing or if moisture is desired for Holding Check water level every 3 hours 2 hours when Proofing and refill with clean HOT tap water as necessary Water pan does not have to be filled for Heating Proofing requires water pan to be filled HEATING INSTRUCTIONS 2 U KANTED rem T 3 B i Only HEAT VAL FEO 1 Set Combination Module switch to HEAT 2 Set POWER switch to the ON position Power indicator light will turn on 3 Set TEMPERATURE control to 9 4 Pre heat cabinet until desired temperature is reached typical heat up time from 77 25C ambient to 160 71C is
10. ort out on the metal causing permanent damage Both the element and main power switch with wires on switch must be replaced 6 If the temperature on the LED Thermometer is not reading a constant temperature it must be replaced along with its power supply transformer Limited Warranty All equipment which is sold under Avantco trademark and used for commercial purpose is warranted against defects in materials and workmanship The warranty runs for one year from the date of original installation and is for the benefit of the original purchaser only All other Warranties Expressed or Implied Statutory or Otherwise including Without Limitation any implied Warranty of Merchantability or Fitness for Purposes are excluded The Seller shall in no event be liable for direct indirect or consequential damages in connection with Avantco commercial products This warranty is not effective if damage occurs because of accident carelessness improper installation lack of proper set up Supervision when required or if the equipment is installed or operated in any manner contrary to the installation and operating instructions In these cases repairs will be made at a reasonable cost Work performed by unauthorized personnel or unauthorized service agencies voids this Warranty 1 year warranty applies to electrical components Defects in any non electrical components will be covered within 90 days of the purchase date This warranty does not apply to
11. pment com 5 C U i 7 gt EQUIPMENT VANTCO t Assembly ine Cab 1 HP11836 Diagram 11 www AvantcoEquipment com EQUIPMENT User Manual VANTCO 1 HPU1836 Diagram i pu Es Sy kt b Li Lu us 0 o n dra U Myy 5 iust AA EN AAA AAA Uri D HL 9 Wiz e Li i MES us L TE da Mog E A ac Ka i 6 LA z CA aa AAA AA AA SE s JE BR Eh BE HAMANN 12 www AvantcoEquipment com EQUIPMENT VANTCO User Manua 177HEAT1836 Diagram a 0L a ee Be Hala feh B Bp EE Se ta A 1a T at A i www AvantcoEquipment com 13 User Manual AVANTCO 177HPU1812 Diagram 14 www AvantcoEquipment com EQUIPMENT VANTCO User Manual 177HPI1812 Diagram www AvantcoEquipment com 15 EQUIPMENT VANTCO User Manual Cabinets Parts Du Use for Cabinets men Replacement Part No 07 HC1812HP 04 07 HC1836HP 04 16 177HEAT1836 177HPI1812 177HEAT1812 177HEATI1812 Magnetic Strip Include top 1pc 177HPU1836 08 09 Right Left side 2pcs Magnetic Strip for door 1812 08 09 Magnetic Strip for door 1836
12. vered 175 F 79 C Egg Patties Uncovered 180 F 82 C French Fries Uncovered 185 F 85 C Fried Chicken Uncovered 180 185 F 82 85 C Fried Fish Uncovered 180 F 82 C Hamburgers Covered 180 F 82 C Lasagna Covered 185 F 85 C Mashed Potatoes Covered 175 F 79 C Mixed Veggies Covered 170 175 F 77 79 C Pancakes Covered 175 F 79 C Pastas Covered 180 F 82 C Peas Covered 170 175 F 77 79 C Pizza Uncovered 175 180 F 79 82 C Roast Beef Uncovered 170 180 F 77 82 C Roast Pork Uncovered 170 180 F 77 82 C Scalloped Potatoes Covered 175 F 79 C Strip Steak Uncovered 160 170 F 71 77 C Turkey Uncovered 170 180 F 77 82 C Waffles Covered 175 F 79 C Whole Chicken Uncovered 170 180 F 77 82 C www AvantcoEquipment com EQUIPMENT User Manual VANTCO Drawer Assembly HCD1500 Drawer Diagram 8 www AvantcoEquipment com AVANTCO VETA VEEN HCD1500H Drawer Diagram www AvantcoEquipment com 9 EQUIPMENT User Manual VANTCO Drawer Replacement Parts Part Description HCD1500 Qty HCD1500H Qty m m BEE a pm HCD 016 Main Switch with Red Light HCD 019 Limit Thermostat HCD 034 HCD 017 HCD 011 Heating element 900W HCD 010 Heating element 600W HCD 008 SS Water Pan mE N A HCD 009 Heating element 600W 4111141114444 HCD 036 Heat Proof Switch with Red Light 10 www AvantcoEqui
Download Pdf Manuals
Related Search