CCTV Tester Pro (manual).
Contents
1. range by press SID only manual range supply Manual range 0 000mA gt 6 600mA range 00 00mA gt 66 00mA range 000 0mA gt 660 0mA range 33 CCTV Tester User s Manual 00 00A gt 10 00A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates over range situation and the higher range has to be selected When the value scale to be measured is unknown beforehand set the range selector at the highest position The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator In AC mode only can input AC if not will damage the meter E Resistance Measuring WARNING When measuring in circuit resistance be sure the circuit under test has all power removed and that all capacitors have discharged fully a Connect the black test lead to the COM jack and the red test lead to the V Q jack b Press O 9 to select 2 enter the Q measurement Auto range by press key and manual range by press IL A Manual range Connect the red lead to black leads will display the measure range 000 00 gt 6600 range 0 000KQ gt 6 600KQ range 00 00KQ gt 66 00KQ range 000 0KQ gt 660 0KQ range 0 000MQ gt2. a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack b pe Ce select A enter the DC current measurement Manual range by press SDD only manual range supply Manual range 0 000mA gt 6 6mA range 00 00mA gt 66 00mA range 000 0mA gt 660 0mA range 32 CCTV Tester User s Manual 00 00A gt 10 00A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates over range situation and the higher range has to be selected When the value scale to be measured is unknown beforehand set the range selector at the highest position The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator D AC Current Measuring Only Manual range WARNING Shut down the power of the tested circuit and then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack b Press 3 to select A enter the AC current measurement Manual
3. CCTV Tester E a a a e 10 CCTV Tester User s Manual OSD menu The charge indicator it lights red while the battery is being charged As the charging is complete the indicator turns off automatically The data transmission indicator it lights red while the data is being transmitted The data reception indicator it lights red while the data is being received The power indicator it lights green while the tester is powered on Set key press it to enter sub menu to set the parameters of functions Press more than 2 seconds turn on or off the device short press to turn on or off the menu display Confirm Open Confirm the setting of parameters open or enlarge the aperture Return Close Return or cancel while setting parameters of the menu close or decrease the aperture Upward Select the item which will be set or add the value of the parameter Tilt the PTZ upward User defined key User setting function the default is PTZ controller LED Lamp Rightward Enter the sub menu or select the parameter whose value will be changed Add the value of the parameter Pan the PTZ right Cp gt Te O SET Return eose lt P Voltage current resistance and capacitance measuring continuity testing diode testing Downward Select the item which will be set or reduce the value of the parameter Tilt the PTZ downward Leftward Enter the
4. measuring the amplitude of the video sync pulse for determining the video lev el is correct and that the coaxial cable connectivity Sync level range is 300 35mV in PAL format NT SC format 40 SIRE the level is too low will cause the image to fracture or scroll Level is too high will reduce the image color levels and dynamic range COLOR BURST chroma level Measuring camera color burst level to determine whether the coaxial ca ble transmission for the best detail and color Chroma standard level is 280mV in PAL format and is 40 IRE in NTSC format Chroma level is low Chroma level is low the color will become dark color level is too low the details of monitor reception image will be lost and even become black and white chroma level is too high the image will be displayed spot affect the image detail and clarity Coaxial cable is too long will reduce the chroma level CCTV Tester User s Manual 2 4 Accessories 1 CCTV tester 2 Power Supply DC5V 1 2 1 5A with USB cable 3 Cable test box or wire tracer 4 Lithium Ion Polymer Battery 3 7V DC 3000mAh 5 BNC cable 6 RS485 cable 7 SC ST connector Only for the optical power meter models 8 Multimeter test leads one pair of red and black only for the Multimeter models 9 Power cable 10 Audio cable 11 TDR alligator clamp only for TDR models 12 Safety cord 13 Tool bag 14 Instruction Manual CCTV Tester User s Manual 2 5 Front Panel 13 09
5. 22 TDR break point and short circuit measurement optional function refer to the last 2 3 23 Visual fault locator optional function refer to the last page JI 2 3 24 LED JAP AA SR S RASE SNS aa 7 23 25 F15 Fr User defined shorte t KEYS ii 7 2 3 26 Video level meter optional function refer to the last page 7 24 PCOS O 9 A mm mmm mm mmm 10 3 ODA NANA ARA aaa 14 SNE IST a A 14 a o A e is ididiisiididaisddadidadsddadidaddodddidaddodddiddddodddes todd isde dii 15 3349819 Mid 15 SA eE E OOOO 16 BREVA COOP HAT EA UU 19 3 3 3 Video level meter optional A ko o o kao aa nana n nana anno a aaa aaa naka nana nana naaa a aaaakna 21 3 3 Video NN 22 SOD PT Zaddr ss seat muuska 23 3 3 6 10x zoom image display and Video out sees eee 24 A 24 O la oa A ia 24 29 Record Play b ck aae aa E E ra Nara ai 25 3 3 10 Cable Scar OPUOMAL iii ta 25 3 3 11 PING di a oa ica 26 e Ag yy 27 ER T lt 1 aa 28 SiS MACE UT Mom TTT 28 39 1S O 29 O 29 3 3 17 Digital Multimeter optional rsrsrsrsrs ran an aa E R R 30 3 3 18 Optical Power Meter OPtiOnal sssssssssssrsrsrsrssrsesesrrrnesesesrrnrnrsrnrrnrr ene rrn ene rn nn rn nn en 38 3 3 19 Visual Fault Locator optional sese esse eee 39 DNA A 39 ERP A NE NE NO 41 3 22 A 41 HI DIA CU rt 42 SBA ONI e E O RINE 43 34 DELV LA POWER ananas vanan aven 43 A r O EME on EEE aaa aaa 44 AMA A ao 44 R 1 OEEO ED
6. 6 600M2 range 34 CCTV Tester User s Manual 00 00 MZ gt 66 00MQ range c Connect test leads across the resistance under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates over range situation and the higher range has to be selected F Continuity Testing WARNING When testing the circuit continuity be sure that the power of the circuit has been shut down and all capacitors have been discharged fully a Connect the black test lead to the COM jack and the red test lead to the V Q jack b Press 6 0 to select 0 enter the continuity test c Connect test leads across two point of the circuit under testing d If continuity exists i e resistance less than about 50Q built in buzzer will sound e You can get reading from LCD G Diode Testing a Connect the black test lead to the COM jack and the red test lead to the V Q jack the red lead anode b Press 6 0 to select Y enter the diode testing c Connect test red lead across to the anode the black lead to the cathode of the diode under testing d Connect test red lead across to the cathode the black lead to the anode of the diode under testing E Tested diode forward voltage low 30mv there is sound indication then can finish the testing quickly without view the screen F The capacitance of a capacitor should be tested separately should not test
7. BNC cable network cable control cable break point and short circuits location It improves working efficiency 2 3 23 Visual fault locator optional function refer to the last page Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi mode and single mode fiber s bending and breakage and Continuous light emitting and 1HZ 2Hz modulating light output It is indispensable tool in fiber project constructing fiber net work maintaining optical component manufacture and research 2 3 24 LED lamp It is useful for the Engineer to install and maintain security system at night LED On Off pressing button easy operation 2 3 25 F1 F2 User defined shortcut keys The user defined shortcut key is designed for improving the efficiency for the engineer anytime press easy to operate 2 3 26 Video level meter optional function refer to the last page PEAK video signal level SYNC signal level COLOR BURST chroma level measurement Use hardware high frequency sampling and processing technology test the Peak video signal SYNC si gnal level COLOR BURST chroma level more accurate CCTV Tester User s Manual PEAK video signal level Measuring peak video signal the video signal level is 1000 175mV in PAL format NTSC format 140 15IRE the level is too low will cause the image to dim reducing dynamic range Level is too high will lead to virtual shadow reducing the definition of the image The SYNC signal level
8. SYNC signal level 280 35mV 21 CCTV Tester User s Manual PEAK video signal level Measuring peak video signal the video signal level is 1000 175mV in PAL format NTSC format 140 15IRE the level is too low will cause the image to dim reducing dynamic range Level is too high will lead to virtual shadow reducing the definition of the image The SYNC signal level measuring the amplitude of the video sync pulse for determining the video lev el is correct and the coaxial cable connectivity Sync level range is 300 35mV in PAL format NTSC format 40 SIRE the level is too low will cause the image to fracture or scroll Level is too high will reduce the image color levels and dynamic range COLOR BURST chroma level Measuring camera color burst level to determine whether the coaxial cable transmission for the best detail and color Chroma standard level is 280mV in PAL format and is 40 IRE in NTSC format Chroma level is low the color will become dark color level is too low the details of monitor reception image will be lost and even become black and white chroma level is too high the image will be displayed spot affect the image detail and clarity Coaxial cable is too long will reduce the chroma level 3 3 4 Video setting Press 6 9 to the menu ES gt press to enter Video setting magar C k Contrast V ani E Saturat kont 5 9216207 PING LCD brightness contrast color saturation can
9. or move the cursor to Format LCD display select Type select Format the tester send the color bars from the Video out port Press the key O Or 6 to switching the video output formats when select LCD press the key O or 9 switching the display content Press the to turn off the menu sending or receiving image to display full screen Press it again display the Color bar generator menu In the color bar generator mode output different standard color bar and received by Video IN port Display the video input and output This feature is available for test monitoring transmission channels such as optical video transmitter and receiver video cables etc the Video out port connect the sending port of the optical video transmitter the Video in port connect the receiving port Image receiving connect the Video OUT port to the Video in port Video generator send the color bars to choose the direction key change the display select for the Video input The screen is in the image receiving state if cannot receive the image the screen display NO VIDEO if received display the sending and receiving consistent color bar Application A When maintain the dome camera send the image to the monitoring center If the monitoring center can receive the image it means that the Video transmission channel normal in addition the monitor center can judge the image quality through
10. range switch Auto 3 OPERATING INSTRUCTION A DC Voltage Measuring WARNING You can t input the voltage which more than 660V DC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V Q jack b Press 0 to select U enter the DC voltage measurement c Auto range by press key and manual range by press SIL gt d Manual range 0 000V gt 6 600V range 00 00V gt 66 00V range 000 0V gt 660 0V range 000 0mV gt 660 0mV range 31 CCTV Tester User s Manual B AC Voltage Measuring WARNING You can t input the voltage which more than 660V AC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V Q jack b Press O 0 to select U enter the AC voltage measurement Auto range by press key and manual range by press lt PLD Manual range 0 000V gt 6 600V range 00 00V gt 66 00V range 000 0V gt 660 0V range 000 0mV gt 660 0mV range C DC Current Measuring only manual range WARNING Shut down the power of the tested circuit and then connect the meter with the circuit for measurement
11. search 08 30 0M Auto Poweroff 20 Min KeyPad tone On Protocol Pelco D Language English Port RS485 Brightness 5 Baud 9600 Address 1 Restore Factory Default F1 PTZ controller Far Near gt Start search F2 Device setting Wid Tele gt Adjust address S N 010201186260081 I kose Note This function need to reset after each time turn off Press key to set protocol communication port communication rate make them the same as PTZ camera Press button the tester will search up the ID guickly and continuously When the ID is searched WIDE the PTZ camera will pan right At this time please press to stop searching up CCTV Tester User s Manual Press the key manual single step decreasing button the tester will search up the ID step by step When the ID is searched the PTZ camera will stop panning Press button the tester will search up the ID quickly and continuously When the ID is searched the PTZ camera will pan left At this time please press to stop searching up Press is searched the PTZ camera will stop panning Manual search address Press or when the address found Press the direction control button O 6 to adjust Speed Dome Camera Press button to guit manual single step incremental button the tester will search up the ID step by step When the ID to search the address gradually the image will flash 3 3 6 10x zoom image display and Video out While video input press
12. testing 3 3 12 Cable tester Press to menu E press E 09 pes PEHOTE Cable tester Cable tester gt UTP PORT NT al Test LAN cable or telephone cable Remote kit 255 Cable Others Connect LAN cable or telephone cable with the CCTV tester and cable tester And then the connecting status cable type and the sequence of wires will be displayed as well as the serial number of the cable tester kit 27 CCTV Tester User s Manual Note if No cable tester box it can be used with the wire tracker CCTV Tester CCTV Tester 3 3 13 Port flicker Press O 0 to select g and then press Ege enter Press E signal to make the connected PoE port flicker at special freguency Press to stop and press to guit to start the tester send the Tf the tester and PoE port are not well connected there won t be any change on the PoE port 13 000 NES Port flicker Port Flicker EL nm Application The tester will send special signals to make the connected PoE port flicker at special frequency which will enable the installers to easily and guickly find the connected ethernet cable This function can prevent mistakenly insertion or disconnection non corresponding cable to artificially interrupt network connection 3 3 14 Link monitor Press O 9 to select ii and then press to enter 28 CCTV Tester User s Manual 13 08 CHH Link monitor 08 30 RP Status 0
13. the faulty cable Msc The TDR reflect signal could be affected by the cable quality cable s not well connected etc to cause the different TDR measurement The TDR measurement is for reference only 40 CCTV Tester User s Manual 3 3 21 Data monitor E Press 6 0 to select es press DATA Datat monitor 08 300 0m Data moniter Baud 4800 P Pelco D FF 01 00 02 28 00 2B FF 01 00 00 00 00 01 VFL TOR ATA Press DL to choose the baud rate of RS485 RS232 it must be the same as the DVR or the Control keyboard The DVR or Control keyboard send the code to the tester if it can be read the protocol will shown on the upper right like Pelco D if not like P Press to empty while the tester receives the code Though the RS485 port display the PTZ control code of the multifunctional keyboard or the DVR Controller can check the status of the RS485 transmission through the code on the display The RS485 communication rate must be the same Application Check the RS485 communication states of the video optical transmitter whether normal Engineer can analyze the protocol and check the data through the displayed code 3 3 22 Time setting Pi A A TESS 6 9 to menu press to enter 13 000 Time setting 08 30 0 Time setting TIME si T i Time 2013 02 18 Date 16 27 38 41 CCTV Tester User s Manual Msc Press O to set the parameter of the time press to
14. to check Power the camera with DC12V 1A power output from the tester It is helpful for demo and testing where there is no power supply available VIDEO OUT DC 12VAA OUTPUT 666 VIDEO IN An otice a Don t input any power into the DC12 1A OUTPUT port of the CCTV tester to avoid destroy b Don t output this DC12V 1A power to the power input port of the CCTV tester to avoid destroy c When the requirement of the camera is higher than 1A the CCTV tester will enter protection mode Disconnect all the connections of the CCTV tester and then connect the CCTV tester with power adaptor to resume the CCTV tester d Make sure the the tester is full charged or more than 3 bars or it will be short circuit 43 CCTV Tester User s Manual 3 5 Audio input test Test the audio input from pickup devices Connect the tester and pickup device with the audio cable AUDIO IN L CCTV Tester 3 6 LED lamp With the LED lamp can work in the evening or in the dark Turn on the tester press for several seconds and the LED lamp turn on press and turn it off Ms Laser is harmful so especially you must protect your eyes When the LD working please don t let your eyes exposure to laser 4 Specifications 4 1 General Specifications Video Test Signal mode NTSC PAL Auto adapt Display 3 5 inch digital TFT LCD 480 RGB x 320 resolution LCD adjustment Brightness Co
15. when the charging is completed A Notice When the Charge Indicator turns off the battery is approximately 90 charged The charging time can be extended for about hour and the charging time within 8 hours will not damage the battery A Press the RESET key at the left of the instrument to restore the default settings when the instrument works abnormally Multimeter the red and black multimeter pen must insert the corresponding port 14 CCTV Tester User s Manual 3 2 Instrument connection 1 The camera or dome video output is connected to CCTV Tester VIDEO IN the image display on the tester 2 CCTV Tester VIDEO OUT interface connect to the Video input of monitor and optical video transmitter and receiver the image display on the tester and monitor 3 Connect the camera or the speed dome RS485 controller cable to the tester RS485 interface Note positive and negative connection of the cable Support RS232 PTZ controller connect the RS232cable to RS232 interface of the tester 3 3 OSD Menu PTZ controller a M Press the key 0 to turn on KR EJ a BAR wa ES sta H Press the key again to turn off also can set time off E PING M Enter the menu choose one function to enter short press 15 CCTV Tester User s Manual the key Close the menu bar at the top of the screen full screen display press it again turn it on H Press the key to enter the menu Continuously press quickly s
16. 1 192 168 0 1 J 02 192 168 0 2 y 03 192 168 0 3 Link monitor No IP Address gt UTP PORT A dd ime gt Start 04 192 168 0 4 05 192 168 5 Add the IP address make sure the network segment and the setting IP address are consistent choose start and press to link monitor If the status is ey means the IP address is occupied if the status is x means the IP address is available Application Add an IP camera or other network device to the current network group the new IP address must not be occupied otherwise it will cause IP conflicts and stop the equipment normal working Link monitor can check if the new setting IP address is occupied 3 3 15 IP address scan Connect the cable to the LAN port press O 6 to select to enter Press Set IP press 6 9 to set the local IP address the network segment and the network devices must be consistent After setting move the cursor to Start press Enter to scan the IP camera or other network equipment address 12 08 OH rhad 08 30001 254 4 1 i 2 0 10 LINK IP Scan Bi i 11 AL EN i 0 23 Total 12 RCH VOL a 3 3 16 POE tester Press O 0 to select us and then press supply equipment s POE port and the tester s PSE IN port Connect IP camera or wireless AP to enter Connect the cable to the power equipment connect tester s LAN port the POE voltage and the cable s pin connection status show on th
17. 44 4 1 General Specification 44 4 2 M ltimeter specifications enana idad 47 4 3 Optical power meter specifications nena nena a e eea eee a aaea 50 bala aa TT 50 CCTV Tester User s Manual 1 Safety information Notice The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital gas station etc To prevent the functional decline or failure the product should not be sprinkled or damped The exposed part of the tester should not be touched by the dust and liquid During transportation and use it is highly recommended to avoid the violent collision and vibration of the tester lest damaging components and causing failure Don t leave the tester alone while charging and recharging If the battery is found severely hot the tester should be powered off from the electric source at once The tester should not be charged over 8 hours Don t use the tester where the humidity is high Once the tester is damp power off immediately and move away other connected cables The tester should not be used in the environment with the flammable gas Do not disassemble the instrument since no component inside can be repaired by the user If the disassembly is necessary indeed please contact with the technician of our company The instrument should not be used under the environment with strong electromagnetic int
18. 5 6 0 1mV 6 600V ImV 66 00V 0 8 6 10mV 660 0V 100mV DC Current Range Accuracy Resolution 6 600mA luA 66 00mA 0 5 3 10uA 660 0mA 100u A 10 00A 1 5 10mA AC Current Range Accuracy Resolution 6 600mA luA 66 00mA 0 5 3 10uA 660 0mA 100uA 10 00A 1 5 10mA Resistance Range Accuracy Resolution 660 09 0 8 5 0 1Q 48 CCTV Tester User s Manual 6 600KQ 10 66 00KQ 10Q 0 8 2 660 0KQ 100Q 6 600MQ 1KQ 66M2 12 5 10KQ Continuity Range Resolution Function 660 00 0 10 The measurement value less 300 530 the tester will sound Diode Range Resolution Function Schottky diode 0 15 0 25V 2 0V ImV rectifier diode 0 6 1 0V triode PN junction 0 5 0 8V Capacitance Range Accuracy Resolution 6 600nF 0 5 20 IpF 66 00nF 10pF 660 0nF 100pF 3 5 8 6 600uF InF 66 00uF 10nF 660 0uF 100nF 6 600mF 5 8 luF 66 00mF 10uF 49 CCTV Tester User s Manual 4 3 Optical power meter specifications Measure Range dBm 70 10dBm Wavelength nm 850nm 1300nm 1310nm 1490nm 1550nm 1625nm Detector InGaAs lt 3 dB 10dBm 22 C Uncertainly lt 45 dB full range 22 C Display Resolution Linear 0 1 Nonlinear 0 01dBm Operating Temperature C 10 50 Storage Tem
19. 8 screenshot and video file and the current file is the third press to guit the latest storage image Press O 6 to choose the files Then press to shown all the storage files press PED 10 choose the files Press Enter OPEN to enter the files press O 0 to choose the image 13 38 EL Record playback 20130201 K 20130203 20130216 3 3 10 Cable Scan optional Connect the cable to the UTP port or the CABLE SCAN VIDEO OUT port on the top Press O 0 to select then press to enter press O to choose the audio type 25 CCTV Tester User s Manual 13 080 Cable Scan 3 Cable Scan Cable Scan aii TYPE 8 TYPE 1 ni A gt Type Select gt Type Select Turn on the cable scan use the copper pin to search the cable with loudest voice means it is connected with the tester Four Audio types can choose LED lamp is convenient to work in dark or at night Press the button to adjust the volume use two batteries size AAA Application It s convenient for people to find out the other end of the cable in security maintenance and network engineering While searching BNC cable connect one port of the alligator clips to the copper core or copper net of the BNC cable the other one to connect the earth wire barred windows Are The battery of the wire tracer must according to corresponding positive pole and negative pole or damage the tester Msc While r
20. 9 to accelerate the value changing Press the key Call some special preset number can call the dome camera menu A Check and set the protocols address interface and baud must be the same as the dome camera then can test and control After setting the parameter the tester can control the PTZ and lens SP Press the key 0 to control the PTZ direction of rotation Press the key to switch on or turn off the aperture Press the key adjust the focus manually Press the key 1 Set and go PS Set PS manually adjust the zoom A P T Z the camera to desired position B Press the key to enter the PTZ controller submenu Press the key QED Move the yellow cursor to Set PS Press the key 6 9 to select the preset position number El OPEN Press enter key to complete preset position setting or preset return the key to give up set position setting Go PS Call the preset position 1 128 The PTZ camera will go to the desired preset position In PTZ Controller mode Press the key to t enter PTZ controller submenu Press the key 68 Move the yellow cursor to GO ps to select the preset position number Then press the enter key to complete preset position setting or preset RETURN key to give up preset position setting Camera moves to the preset position immediately Lens zoom focus and iris is automatically changed to the preset parameters preset the camera image displayed on the monitor Tip
21. CCTV Tester Manual v2 10 Thank you for purchasing the CCTV security tester Please read the manual before using the CCTV tester and use properly For using the CCTV tester safely please first read the Safety Information carefully in the manual The manual should be kept well in case of reference Keep the S N label for after sale service within warranty period Product without S N label will be charged for repair service If there is any question or problem while using the CCTV tester or damages occurred on the product please contact our technical Department Content 1 Safety InfoMine 1 256 A EEE CETRO 2 E R RN 2 RTT 3 A EO EO OEEO PE OEEO OEEO HEART HEAT ETATS 4 MDU Video ENA MESNE Ao o 4 O WIPO SIGHT EV E L O ii la 4 SN VAT A TN 4 2 3 4 Enhanced Color bar generator 4 235 DOV TA POWE aaa 5 725 PRU T 5 eq O 5 A I 5 DOD PTZ address TT 5 2 3 10 Image magnification 1OXZOOM ea 5 221 Via his oesl 5 LISAL VIdeo TE COLA US E EE E E EE A a 5 2215 Video play BACK dads OAR Aa aaa aaa rade 6 2 3 14 Cable scan optional function refer to the last page 6 WSUS TT o MII 6 2 3 16 Pad dress SCAN iaa LAASI AIDI ea AAI AUI 6 E ND tud e T 6 DiS AB PIING LE TTT 6 E ERI Lo EPR o ENNS Eiai daa 6 2 3 20 Digital multimeter optional function refer to the last page 6 2 3 21 Optical Power Meter optional function refer to the last page 7 2 3
22. Tester User s Manual TOR Tester 08 30 0 TOR Tester 08 30 EJ Break Om Break 100 m Name SYV 75 5 Name Type BNC Type Speed 200 4 gt Adjust Speed 200 4 gt Adjust TTT Calibration Press Enter to start Built in BNC network cable RVV control cable Telephone line can test 12 groups user defined cable can be set A A P Enter Press ser to line type interface press lt gt lt gt to choose the line type press to save and start testing Press 6 9 to adjust the speed if select the user defined cable type adjust the speed after the calibration User defined calibration Choose the cable 100 meters to 200 meters more than 50 meters press to set the user defined calibration Press CA to select user 1 to calibrate 12 groups user defined can be set Cable Type Select TOR Tester ETTE SYV 75 3 SYV 75 2 RVVP RVV UTP CAT 5E UTP CAT 6E Telephone line User User 2 Break 100 m Name User 1 Type BNC Speed 200 4 Adjust 2 3 4 5 6 L 8 9 0 Start Calibration Press Enter to start Press 6 0 to Adjust press to cable type press 6 0 to choose the cable style press DEN to Speed and press 6 6 to adjust While display length is the same as the actual length press to save It can be used for the same cable after the calibration Application The disconnection and short circuit display in the tester it is more convenient and efficient to repair
23. User s Manual Ri 2 Measure the first optical fiber pressing the key rose Optical Power Meter CLOSE under any display unit then the current fiber power value is 70 00 dBm stored as the base reference value Hold Relative 3 Input another optical fiber to be measured the relative power 55071300 Y 1490 1550 1625 4 Wavelength value is displayed The optical power meter displays the end end loss av mW dBm of the fiber under test the unit of loss value must be dB Data hold and Relative measuring use together the data is yellow while the function is effect 3 3 19 Visual Fault Locator optional Press O 6 to select E then press tener Insert the fiber to the device s VFL interface default output power is 10mW and the wavelength is 650nm Press X to adjust pulse mode and stable model 13 080 Visible laser 08 30 H Visible laser 08 30 H Visible laser Mode stable Mode pulse 1Hz 10mU 10mU VFL TOR DATA 650nm A EA Ass TIME SET 650nm 4 Mode Select 3 3 20 TDR Tester optional An The testing cable can t be connected to any equipment or it will damage the tester Connect Alligator clip cable to the TDR port and the cable must connect well before testing or it will influence the accuracy Press O 0 to select TDR TDR Tester EDE Short 130 m Name SYV 75 5 Type BNC Speed 207 4 gt Adjust ETFI Calibration Press Enter to start 39 CCTV
24. be adjusted Restore Default Enter gt The CCTV tester auto displays the format PAL NTSC of video input and analysis the input video signal level gt The Video Level should be within the indicated range Levels that are too low will result in a dim picture with reduced dynamic range A Video Level that is too high will result in washed out 22 CCTV Tester User s Manual pictures with decreased Depending on the type of camera connected to the CCTV tester the Video Format will automatically change between NTSC and PAL and the Video Level will automatically change between IRE Institute of Radio Engineers and mV NTSC signals measured in IRE units PAL signals measured in mV 3 3 5 PTZ address search a Press 0 to select gt press to enter SEARCH 13 08 010 APTZ address search 08 30 PTZ address search Protocol Pelco D lt I j Hd Port RS485 TR Baud 9600 Address 1 L FS de E Far Near gt Start search SEARCH PLAY SCAN Wid Tele gt Adjust address gt Asoc Please isolate the PTZ camera with other PTZ cameras before searching up Otherwise all the PTZ cameras in the same system will pan at the same time Press 6 0 to select and then press to enter as follow picture Select to Address SET search press 6 9 to select ON or OFF then Press to save The PTZ address search function a displays in the main menu SEARCH Device setting ERELL E y APTZ address
25. d Hold and display the measured value Relative measurement Display the relative power value 46 CCTV Tester User s Manual Visual fault locator Visual fault locator Test fiber s bending and breakage SM and MM fiber TDR Tester TDR Tester breakpoint and short circuit measurement BNC cable telephone cable POWER Power Adapter DC 5V 1 5A Battery Built in 3 7V Lithium polymer battery 3000mAh Rechargeable After charging 3 4 hour working time lasts 11 hours Low Consumption Energy saving technology the battery icon real time display Parameter Operation setting English Chinese and other languages OSD menu Auto off 5 60 mins Keytone On Off General Working Temperature 10 C 50 C Working Humidity 30 90 Dimension Weight 194mm x 112mm x 48mm 540g 4 2 Multimeter specifications Counts 6600 6600 Conversion rate 3 times s Current modes for clamp meter with ZERO function Isolation the Multimeter connector must be isolated with the other connector DC Voltage Range Accuracy Resolution 660mV Manual range 0 1 mV 0 3 4 6 600V ImV 47 CCTV Tester User s Manual 66 00V 10mV 660 0V 100mV AC Voltage Range Accuracy Resolution 660 0mV Manual range 1
26. d network device with Video display PTZ control DC12v output power Audio test Color generator RS 485 Data searching and Cable testing which are the same to the previous models The new developed functions include POE power supply testing PING testing IP address scan Video screen shot Video record Image magnification Port flicker Cable search LED lamp etc The new tester also has built in TDR cable testing which is specialized designed for BNC cable testing in the security monitoring system This function can accurately measure BNC cable and network cable s break point and short circuit location The new tester designed with easy operation and portability makes it simple for a cctv technician or installer to install and maintain CCTV systems improving work efficiency by reducing time in the field CCTV Tester User s Manual 2 2 Features gt VV VV V vv V V WV v Vv Vv WV V English Chinese and other languages optional 3 5 TFT LCD 480 RGB x320 LED Lamp easy to operate at night Micro SD card moveable User defined shortcut keys F1 and F2 LCD screen brightness contrast color Saturation adjustable Automatically adapts and displays the video format of NTSC PAL 10xzoom video image can be magnified to view the details easy to use Video record and playback Snapshot and save the current image as JPG file in the SD card PING testing test IP camera or other network devices ethernet port whether work normal
27. e screen 29 CCTV Tester User s Manual 13 09 1 PoE tester o8 30 Poe tester PORT DMM A Note the Poe power supply equipment POE Switch PSE power supply equipment must be connected to the PSE IN port the powered device such as IP camera or wireless AP must be connected to the LAN port then it measure the voltage correctly PIS do not connect POE power supply port to the UTP SCAN port otherwise it will damage the tester 3 3 17 Digital Multimeter optional Enter To press O 0 to select press to enter 13 09 01 fal Digital Multimeter 08 30 MM kto 0 000 V Digital Multimeter 1 Funetion Button 3 Auto range Eik Data hold Relative measuring O 6 Function select lt 2 lt gt Manual range 2 SYMBOLS UDAAQ DEF 4 gt Function av Range U DC Voltage Measuring U AC Voltage Measuring A DC Current Measuring A AC Current Measuring A Resistance Measuring D Continuity Testing Diode Testing F Capacitance Measuring 30 CCTV Tester User s Manual AC DC Voltage and current measurement state display Auto range The Multimeter auto adjust the range by input signal or tested components Data hold Hold data Relative Display the relative measurement value measurement Press the key to change display state 10A socket In 10A current measurement state indicate use 10A socket The current measurement value over the range if in the Auto range state to Over
28. eceive the audio signal from the tester it will be influenced by the other signal and make some noise 3 3 11 PING Test Connect the cable to the LAN port press O 9 to select and then press to enter Press PING 6 9 to adjust the IP address Packet Size Timeout TTL Count Press LISP to adjust the parameter 26 CCTV Tester User s Manual 13 08 00 Ping 08 3000 Ping Local IP 192 168 0 120 ys 4192 168 000 001 a Sot ICMP p Setti Pa S caket Setting PTZ LEVEL Packet Size TimeOut ms aE a TTL E Count PLAY SCAN l If IP camera or other ethernet equipment is not connected to the tester connect fail display on the screen The sending and receiving packet amount is 0 the success rate is 0 Press to restart the Ping testing after the IP equipment is well connected If the IP address is correct the sending and receiving packet amount will be consistent the success rate will be 100 Application Ping Connecting 08 30008 Ping Statistics ing i i i Send 004 Received 004 PING testing is the most conventional network debugging tools Lost 000 Haa TDS It is used for testing if the connected IP camera or other network Round Trip Time ms Min Max Avg 0000 0001 0000 t s eth t port i ki 11 d the IP add equipment s ethernet port 1s working normally an e address Gonnect r vr is correct It s normal that the first data packet will be lost when start the PING
29. erference Don t touch the tester with wet hands or waterish things Don t use the detergent to clean and the dry cloth is suggested to use If the dirt is not easy to remove the soft cloth with water or neutral detergent can be used But the cloth should be tweaked sufficiently About digital multimeter Before using you must select the right input jack function and range Never exceed the protection limit values indicated in specifications for each range of measurement When the meter is linked to a measurement circuit do not touch unused terminals Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground CCTV Tester User s Manual a At the manual range when the value scale to be measured is unknown beforehand set the range selector at the highest position a Always be careful when working with voltages above 60V DC or 40V AC keep fingers behind the probe barriers while measuring a Never connect the meter with any voltage source while the function switch is in the current resistance capacitance diode continuity otherwise it will damage the meter a Never perform capacitance measurements unless the capacitor to be measured has been discharged fully a Never measure any of resistance capacitance diode or continuity measurements on live circuits 2 Introduction 2 1 General The new CCTV tester is developed for the On Site installation and maintenance of IP camera analog camera an
30. file 2 3 12 Video record Record and save the current video in the SD card CCTV Tester User s Manual 2 3 13 Video playback Video image and record files are saved in the SD card Storage file directory can be created according to the date 2 3 14 Cable scan optional function refer to the last page Send the specific signal easy to find the connected cable 2 3 15 Port flicker The tester will send special signals to make the connected POE port flicker at special frequency which will enable the installers to easily and quickly find the connected ethernet cable This function can prevent mistakenly insertion or disconnection non corresponding cable to artificially interrupt network connection 2 3 16 IP address scan In digital IP surveillance applications if IP camera s IP address is not clear or forgotten the device cannot be used IP address scan can quickly search the connected IP camera or other network device s IP address 2 3 17 Link monitor To add an IP camera or other network device to the current network group the new IP address must not be occupied otherwise it will cause IP conflicts and stop the equipment normal working Link monitor can check if the new setting IP address is occupied 2 3 18 PING test PING is the most conventional network debugging tools It is used for testing if the connected IP camera or other network equipment s ethernet port is working normally and the IP address is correct 2 3 19 POE teste
31. in the installation of circuit 35 CCTV Tester User s Manual H Capacitance Measuring WARNING To avoid electric shock be sure the capacitors have been discharged fully before measuring the capacitance of a capacitor a Connect the black test lead to the COM jack and the red test lead to the V Q jack b Press O 0 to select enter the capacitance measurement Auto range by press key and manual range by press lt 2 N Manual range 0 000nF gt 6 600nF range 00 00nF 66 00nF range 000 0nF 660 0nF range 00 00uF 66 00uF range 000 0uF gt gt 0 000uF gt 6 6004F range gt gt 660 0uF range gt 0 000mF 6 600mF range 00 00mF gt 66 00mF range c Before connect test leads across two sides of the capacitor under measurement be sure that the capacitor has been discharged fully d You can get reading from LCD Note a The capacitance of a capacitor should be tested separately should not test in the installation of circuit b To avoid electric shock be sure the capacitors have been discharged fully before measuring the ca pacitance of a capacitor cC While testing the capacitance of a capacitor to 660uF the Max time will be 6 6 seconds if the capacitor is leaked or damaged the data can t be read The tester will be normal after disconnecting the capacitor Manual range and Auto range 36 1 CCTV Tester User s Manual Press the key E to change the value press
32. ly and the IP address whether right IP address scan quickly search the IP address for the connected IP camera and other network devices POE voltage measurement test the PoE switch s voltage to IP cameras wireless AP device and other PD devices Device Port flicker easy to find the connected PoE switch port by sending special signals the connected PoE port will flicker at special frequency Link monitor check the setting IP address whether occupied TDR break point and short circuit measurement BNC cable network cable etc PTZ address scan search up the ID of PTZ camera Network cable and Telephone cable testing display the sequence of connection and the NO of the LAN cable Support RS232 RS485 RS422 Rate 600 115200bps adjustable Multi protocol Supports more than thirty PTZ protocols Such as PELCO P PELCO D SAMSUNG PTZ protocol analysis control protocol command displays to check RS485 transmission whether is normal easy to find the fault device CCTV Tester User s Manual gt PTZ control Pan tilts the P T unit zooms in out the lens adjusts the focus aperture and sets and the preset position DC12V IA power output for camera Audio input test test the audio signal from pickup devices Visual fault locator to test fiber s bending and breakage Y Vv Vv WV Lithium Ion Polymer Battery The device employs advanced power control and protection circuit The device is high power efficient energy saving a
33. nd environmental protection It can last 11 hours for normal use after charging for 4 5 hours 2 3 Function 2 3 1 Video signal testing The new cctv tester built in high definition 3 5 LCD TFT 480 RGB x320 full view display screen easy and directly displays the camera image quality Support PAL NTSC LCD screen brightness Contrast Color Saturation adjustable Suitable for field construction and maintenance work 2 3 2 Video signal level test Test video signal strength attenuation longer video signal cable will cause the image to be dim and reduce the image dynamic range video signal is too strong it will cause the virtual shadow and reduce the sharpness of the image It also can real display the video level value if out of range notices will be display in the screen 2 3 3 PTZ controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position 2 3 4 Enhanced Color bar generator Video Generating the PAL NTSC multi system color bar video generator Eight system switchable transmit receive eight system colorful imagines By receiving the video color bar to test the video channel whether transmit normally And judge whether the color is different because of the CCTV Tester User s Manual transmission loss or interference it suitable for Video transmission of the field
34. ntrast Saturation adjustable Video IN OUT 1 channel BNC Input amp 1 channel Output Video Output Mode 1 0 Vp p Video Level test Level test Video signals measured in IRE or mV 44 CCTV Tester User s Manual Video Level meter optional Video Level meter PEAK video signal level SYNC signal level COLOR BURST chroma level measurement PTZ controller Communication Support RS232 and RS485 Compatible with more than 30 protocols such as PELCO D P Samsung PTZ Protocol Panasonic Lilin Yaan etc Baud Rate 600 1200 2400 4800 9600 19200 57600 115200bps Video Signal Generation Color bar generator Output one channel PAL NTSC color bar video signal for testing monitor or video cable red green blue white and black color UTP Cable tester UTP cable test Test UTP cable connection status and display in the screen Read the number of the test box DC12V 1A power output DC12V power output Output DC12V1A power for camera Audio input test Audio input test test the pickup and other audio equipments on the front end RS485 data analysis Data Monitor Captures and analyzes the command data from controlling device 10x Zoom Image Image 10x zoom 10x zoom image display and video out Photograph Video record Record playback Photograph snapshot and save the current image as JPG file Video record Video record and sto
35. perature C 20 70 Connector type FC PC 4 4 Optional models function model A Cc D E F G H 3 5 HVGA LCD v v v v v v v v Image enlarge 1 10 times v v v v v v v v photograph v v v v v v v v Video record v v v v v v v v Record playback v v v v v v v v SD card v v v v v v v v Color bar generator v v v v v v v v Video signal level test v v v v v v v v Protocol capture and display v v v v v v v v PTZ address search v v v v v v v v DC 12V 1A power output v v v v v v v v Audio test v v v v v v v v 50 CCTV Tester User s Manual LED Lamp v v v v v v v v v PING test v Port flicker v POE tester v Link monitor v IP address scan v UTP cable tester v Wire tracker v Digital multimeter v Optical power meter Visual fault locator v TDR Tester A T B T C T D T E T F T G T H T IT C Add Wire vacker ONNI a The data above is only for reference and any change of them will not be informed in advance For E Add Wire tracker OPM E T Add Wire tracker OPM TDR more detailed technical inguiries please feel free to call the Technical Department of our company 51 CCTV Tester User s Manual 52
36. r It can test the PoE voltage when the POE switch is supplying the POE power to IP camera It can clearly display the power and power on the ethernet cable pins each cable pin s voltage and the failure connection of cable pin series numbers 2 3 20 Digital multimeter optional function refer to the last page CCTV Tester built in highly stable and reliable 33 4 digit 6600 digital multimeter It is used for the DC and AC voltage measurement AC and DC current measurement Resistance measurement Continuity test Diode measurements Capacitance measurement Auto Manual measuring range CCTV Tester User s Manual switching relative value measurement and locking It is easy operation and professionally accurate 2 3 21 Optical Power Meter optional function refer to the last page The New tester adopts the most advanced handheld instrument specific integrated chip achieve ultra low power operation with the 3 5 TFT LCD High definition screen display five wavelength calibration points 1625nm 1550nm 1490nm 1310nm 1300nm 850nm Linear or nonlinear optical power display it can measure the optical power value and also be used for Relative measurement of optical fiber link loss It is necessary tool for fibre optic communication cable television system and security system maintenance 2 3 22 TDR break point and short circuit measurement optional function refer to the last page New function TDR cable testing accurately measure
37. rage the file Record playback To view the storage file in the SD card Port flicker Port flicker Find the connected POE port quickly 45 CCTV Tester User s Manual IP scan Link monitor PING test IP scan Find out the connected IP camera or the other network equipment IP address quickly Link monitor Check the IP address whether is occupied Test IP camera or Ethernet port of the other network equipment whether PING testing work normally and check the IP address Cable scan Cable scan Search the cable by the audio signal PoE tester PoE tester Display the power supply voltage and cable connection states Digital Multimeter AC DC Voltage 0 660V auto manual range the min resolution is 0 1mV AC DC current 660 0uA 6 600mA 66 00mA 660 0mA 10 004 Resistance 660 00 6 600kQ 66 00kQ 660 0kQ 6 600MQ 66 00MQ Capacitance 6 6nf 66000uF the min resolution is 1pf Diode 0 2V forward voltage the min resolution is ImV Data hold Hold and display the measured value Relative measurement Display the relative power value Continuity testing Built in buzzer will sound if resistance is lower than 50 Q Testing speed 3 times seconds Data range 6600 6600 Optical power meter Calibrated 850 1300 1310 1490 1550 1625nm Wavelength nm Power range dBm 70 10dBm Sensitivity nW 0 001nW Connector type FC PC Data hol
38. rated range fuse will melt to protect the meter Pls use the same model when CCTV Tester User s Manual 3 3 18 Optical Power Meter optional A zme Enter Press twice or press O 0 and DLS select press to enter OPM 13 08 00 Optical Power Meter 08 30 M Optical Power Meter prm TIME SET 70 00dBm A 850 1300 EYT 1490 1550 1625 4 Wavelength av mW dBm 1 Function Data hold 4 6 9 Wavelength select CODED mW dBm units select 2 Instruction Optical Power Meter 08 300MM A Press MODE key to select Optical power meter 70 00dBm B Absolute power value measurement sole 1 Set the wavelength via 5 9 key the default wavelength 4 gt Wavelength is 1310nm evar cet A 850 1300 EYT 1490 1550 1625 2 Input the optical fiber to be measured the power value is displayed in LCD 3 Linear and nonlinear value of the current optical fiber power can be displayed by pressing COLD key to change the unit to be mW or dBm A Note Pls keep the fiber connector and the dust cap be clean and clean the detector with the special alcohol Optical Power Meter 08 3001 Data hold WIDE A 00 00dBm While testing press to data hold the data will not change Relative A It s convenient to read Press again to quit S ETH 1828 4 gt Wavelength Relative power value optical link loss measurement SUNSET 1 Set the wavelength for measurement 38 CCTV Tester
39. ress the key to save and return If no change Press the key to return setting and then press the key return the PTZ controller function A Protocol A PTZ control ler 13 080 Use the up and down arrow keys to move the yellow cursor to Protocol Pelco D Port RS485 the 4 t 1 n di P l S Baud 9600 e protocol set corresponding Protocol Support more ERE 1 Pan Speed 40 than thirty PTZ protocols Such as Pelco D Samsung Yaan Ts capes 30 Set PS 8 LiLin CSR600 Panasonic Sony EVI etc Press enter to apply B Port Move the yellow cursor to port Select the communication port for the PTZ camera controlling RS232 422 485 C Baud Move the yellow cursor to Baud Select the baud rate according to baud rate of the PTZ camera 600 1200 2400 4800 9600 19200 57600 1 15200bps D Address Set the ID according the ID of PTZ camera 0 254 the setting address data must be consistent the speed dome address E Pan speed Set the pan speed of PTZ camera 0 63 F Tilt speed Set the tilt speed of PTZ camera 0 63 G Set preset position Set PS Move the yellow cursor to SET PS set and save preset position number 1 128 Press the key 6 9 Enter to accelerate the value changing then press the key to save Press to quit H Call the preset position Go ps Move the yellow cursor to Set PS then Setup preset position 1 128 17 CCTV Tester User s Manual Press key 6 or
40. s Preset position setting is saved in the domes Preset position can be set depending on the dome 18 CCTV Tester User s Manual 2 Menu of dome Different dome camera factory control system be used different preset position pls refer to the dome camera manual The provided dome camera enter the the menu by calling preset position 64 this example is for reference only a Press the key to enter PTZ controller submenu b Press the key 6 0 select preset position 64 c Press the key Enter the main menu of the PTZ camera po i OSD menu of dome Call the preset point 064 Go PS 064 MAIN MENU 1 DISPLAY SETUP 2 CAMERA SETUP 3 CONTROL SETUP OSD Menu of Dome For 4 CAMERA MASK SET 5 PROGRAM 6 PAL CAMERA 7 CAM DEFAULT SET 8 DOME RESET 9 EXIT Reference only After Calling the dome camera menu Users can select different function through the arrow keys the dome camera menu operation refer to the manual 3 3 2 Color bar generator Press the key to enter the menu Press the key 6 0 to select the bar a and then press the key ED enter BAR 13 00 EUA 08 30 C E Image generator 08 300 Foriha Pi I Image generator at PAL Mideo output Nideo output p ColorBar gt ph RESER Pe C 2 HANA EE R PLAY SCAN PING ue ESS 19 CCTV Tester User s Manual Test the Color bar generator support global PAL NTSC standard color bar of different output formats Press the key lt gt
41. save Users need to set the time first as the time of the photograph and video record is the same as the Time setting 3 3 23 Device setting Press 6 9 to menu press to enter SET 13 08 Device setting 03 38 0 Device setting Auto Poweroff 20 Min KeyPad tone On Es Language English DATA amp Brightness 5 Address search Om Restore Factory Default F1 PTZ controller F2 Device setting ie S N 010201186260081 Press lt gt or ZS to choose the item press 6 0 to adjust press to save press to quit Auto power off Setting the time of auto shut down Disable 5 10 60 Disable Disable the Auto power off function 5 means the CCTV will power off after 5 minutes when there is no any operation Keypad tone Open or close the beep of pressing keypad Language ENGLISH CHINESE and other languages Brightness Setting the brightness of OSD menu and background 0 7 Address search off on Open or close the PTZ address search Menu Restore factory setting restore the data of the factory F1 user defined keyboard shortcuts Users can set the function as you like press O 9 to select press to save The default value is PTZ controller F2 user defined shortcut key is the same setting of the F1 shortcuts keys The default is Device setting 42 CCTV Tester User s Manual 3 3 24 USB All the photograph files or video record can be uploaded to computer it s convenient
42. sub menu or select the parameter whose value will be changed Reduce the value of the parameter Pan the PTZ left Video record Snapshot capture video image BEE lt gt 0 10xzoom the image display and video out 11 CCTV Tester User s Manual WIDE zoom out the image Near focus Focus the image nearby Far focus Focus the image faraway Menu key TELE zoom in the image 12 CCTV Tester User s Manual cur O e KON Optical power meter interface Optional Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi mode and single mode fiber s bending and breakage 13 CCTV Tester User s Manual 3 Operation 3 1 Installing the Battery The tester has built in lithium ion polymer rechargeable battery The battery cable inside battery cabin should be disconnected for safety during transportation Prior to the use of the instrument the battery cables inside the battery cabin should be well connected Usually it doesn t need to disconnect the cable at the normal use Pressing key continuously can power on or off the tester P EN Pls use the original adaptor and connected cable of the device s At the first time of use the batteries should be completely exhausted and then recharged for 4 or 5 hours yy The Charge Indicator lights red when charging the battery the charge indicator turns off automatically
43. tests such as optical video transmitter and receiver video cable etc The new function color bar can test the image whether shift The color bar red green blue white black test the monitor whether have white or black dot etc 2 3 5 DC12V 1A output power Power the camera with DC12V 1A power output from the tester It is helpful for demo and testing when the power supply is not available 2 3 6 Audio testing Test the audio input from pickup devices Connect the tester and pickup device with the audio cable 2 3 7 Cable tester Test LAN cable or telephone cable Connect LAN cable or telephone cable with the CCTV tester and cable tester And then the connecting status cable type and the sequence of wires will be displayed as well as the serial number of the cable tester kit 2 3 8 PTZ controller Search the Control protocol code from Multifunction keyboard or DVR by RS485 RS232 interface test the PTZ control command data whether received anomaly and RS485 RS232 data transmission Screen displays 16 hexadecimal codes such as PELCO P A000 Add xx xxxxxx AF xx PELCO D FF01 Add xx xxxxxxxx 2 3 9 PTZ address scanning Search up the ID of PTZ camera Help the engineer search the speed dome address guickly 2 3 10 Image magnification 10xZoom Set image 10x zoom can view and display the details by 1x 2x 3x 4x 5x 6x 10X zoom in the monitor and tester 2 3 11 Video snapshot Capture the video image and save the current video frames as JPEG
44. the E to Auto measurement Data hold Press the key to hold the data the value is green Press it again to quit Relative value measurement Press the key the tester Auto save the data the displayed new measurement and relative value is red color Press it again to quit The hold function and the relative value be combined use the display value is yellow The meter protection gt Voltage protection gt Resistance Continuity Diode PTC component Protection You can t input the voltage which more than 660V AC it s possible to show higher voltage but it s may destroy the inner circuit fd Digital Multimeter na 3 813 Uaa 71 Z 4 gt Function av Range kid Digital Multimeter e Hold UUAAA947 4 Function av Range G Digital Multimeter 0 000 Relative UUAS0 7 Z 4 gt Function av Range G Digital Multimeter 08 300 V 08 300 V 08 300 V 08 201 H E H 813 V Hold Relative ay UUAA9947 4 Function av Range Wrong input voltage will Auto enter protection state It only suitable for short and limit time work If the input voltage over 600V will damage the meter gt mA current fuse range 250V 1A change the fuse Pls opens the battery cover to change A Note 10A socket without fuse protection if over the current range Wrong using the 10A socket to measure the voltage will damage the meter 37 if the current over the
45. the received color bar B Test the optical video transmitter and Video cable sending and receiving color bar by itself check the transmission equipment or cable whether normal C Send the pure color bar such as white and black color to test the monitor whether has bright or black dots D Send video signal image test received image whether shift 20 CCTV Tester User s Manual 3 3 3 Video level meter optional T Ente Press O to Jehoose menu nt and press E to enter VLA Use hardware high frequency sampling and processing technology test the Peak video signal SYNC signal level COLOR BURST chroma level more accurate While the tester Video Level Meter 08 30008 receive the video signal it will automatically measure the gt S A s Format PAL B DP G H 1 PEAK video signal level the SYNC signal level and Peak _1100my 7 S 4 280mV COLOBURST level chroma level While in PAL format the SI E Sin y unit will be mV While in NTSC format it will be IRE Video Level Peak to peak leve NTSC 140 IRE PAL 1000 mV Video 20IRE ssccsnsncccevesscuescnsccecscs Burst Level 20IRE f gt JOIRE Syne Level Sync Level peak to peak NTSC 40 IRE URE som PAL 285 7 mV Video signal level 140 15IRE NTSC Chroma level COLOR BURST 40 5IRE SYNC signal level 40 5IRE Video signal level 1000 200mV PAL chroma level COLOR BURST level 280 35mV
46. to 10x zoom and press the button to zoom in the image press to zoom out the image Press to see the details Press Set image 10x zoom can view and display the local details by 1x 2x 3x 4x 5x 6x 10X zoom in to guit the monitor and tester KLE 3 3 7 Photograph While video in Press the key to save the current video frame in the SD card as JPEG file Set storage file according to the date it s convenient to check the tester automatically checks whether have SD card when photograph If no SD card shown no SD Card on the the screen 3 3 8 Video record While video in press gt several seconds the icon is flicking on the top left means the video record is under working and saving the video in the SD card as AVI format Press the flicker icons 24 CCTV Tester User s Manual disappears and stop working Set storage file according to the date it s convenient to check Note press the button gt several seconds and start to the video record 3 3 9 Record playback Press 6 9 to select rom press to enter the latest photograph or video record file display on the screen 13 08 0 Record playback Record playback L Ea SCAN PING As the above picture the photograph file with the icon and the video record file with the icon A 5 Reti m on the top right corner Press to start and stop video playback and press to guit See the above image the 3 0008 in the image means total
47. witch to the desired function menu Anytime press this key to enter the menu H In various functional mode press the key Set the various parameter values M When turn it on press the key wove to enter the function menu continuously press the key O O select different function and press the key to enter H Press the key to switch the menu the square m different square means different interface H Press the key O 13 09 13 000 13 00 Z controller Cable tester Optical Power Meter LA E ES BAR LEVEL ore PORT LINK TOR DATA mawsor SCAN PING SEARCI TIME ii USB OA al select the different function icon then press the key to enter First page menu Second page menu Third page menu 3 3 1 PTZ controller Display the input video images Press the key to enter the menus and set Parameter Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position Display the input image press the key closed the top menu display full screen image Enter PTZ controller if no video input the screen display No video 16 CCTV Tester User s Manual PTZ controller parameter setting In the PTZ CONTROLLER mode as shown above press the key to enter the parameter setting press the key Ss move the yellow cursor to select Press the key O or 9 change the parameter values Then p
Download Pdf Manuals
Related Search