Home

Data 708

1. Some items in the Adjustment mode are password protected While selecting such an item the projector asks you to enter your password Password protection is only available when the password DIP switch on the controller module is in the ON position Contact a BARCO authorized technician when no password is requested during the adjustment procedure and password protection is desired Your password contains 4 digits a Adjusting the projector with the RCU Enter the digits with the numeric keys on the RCU Example 2319 de For each digit entered a X appears on the screen under the displayed text enter password When your password is correct you get access to the Adjustment mode When the entered password is wrong The message Wrong password will be displayed The projector stays on the previous selected item Factory programmed password 0000 198 b adjusting the projector with the local keypad When the compose password menu is displayed select with control disk the first digit of your password and press ENTER Continue by selecting the second digit with the control disk and press ENTER Handle in the same way for the third and fourth digit COMPOSE PASSWORD 229 ZM Selectwith 4 y 7 gt Of a t
2. 5 6 COLOR 3 BRIGHTNESS 1 2 CONTRAST Enter ADJUST Select with 4 4m OF my then lt ENTER gt lt EXIT gt to return Line doubling is possible for component video input sources on standard line frequency If a line doubler is built in the default position of this line doubler is ON active the component video input signal will be displayed as a non interlaced image improved image stability To enable or to disable this line doubler function enter the adjustment mode and change the position of the ON OFF toggle switch see Picture tuning in chapter Guided adjust ment mode or Random access adjustment mode R Y Y B Y S or R Y Ys B Y input selection a Press digit button 5 on the RCU or b With the local keypad to gain access to the local keypad see Local keypad in chapter Location and function of controls Press ADJUST key the General access menu is displayed on the screen Use the control disk to highlight 5 Press ENTER to select the highlighted source Connecting a Component source with Tri level sync R Y Y B Y analog input terminals with Tri level sync input or with Tri level sync on the luminance input 5975977 BARCODATA 708 260597 ofc
3. MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS R amp B CONVERGENCE MID GR CONVERGENCE MID SET TO MIDPOSITION All settings on current block will be overwritten lt ENTER gt to confirm lt EXIT gt to cancel MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS R amp B CONVERGENCE MID GR CONVERGENCE MID Select with 4 or t then lt ENTER gt lt EXIT gt to return 7 7 Service Mode R 8 B convergence mid Item is password protected Highlight R amp B convergence mid with the control disk and press ENTER to set all convergence settings to their midposition A confirmation screen will be displayed first ENTER sets the convergence settings to their midposition EXIT cancels the procedure to set the convergence settings to their midposition Undo R amp B convergence mid When R amp B convergence mid is selected all convergence settings are set to their midposition To cancel this action select Undo R amp B convergence mid by pushing the control disk up or down and press ENTER Undo R 4 B convergence mid is displayed in the Memory management menu in stead off R amp B convergence mid when this latter is pressed An undo is possible as long as the projector is playing on the same source same adjustment block even when some adjustments are already readjusted When undo is presssed all settings are reset
4. SC 4 2 c RCU used in a hardwired configuration 000008 gt Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the rear panel of the projector labelled REMOTE Projector address a Software set up of the projector address See Change Projector Address in chapter Service mode Every projector requires an individual address between 0 and 255 which is set in the Service mode Only projectors with addresses between 0 and 9 can be controlled with the RCU b How to control the projector The projector s address may be setto any value between 0 and 255 When the address is set the projector can be controlled with the RCU for addresses between 0 and 9 Computer e g IBM PC or compatible Apple MAC etc for addresses between 0 and 255 Note A projector will respond to an RCU set to an address of 0 regardless of what address is set in the projector itself c Using the RCU Before using the RCU itis necessary to enter the projector address into the RCU only when that address is between 1 and 9 The projector with the corresponding address will listen to that specific RCU When address 0 zero address is programmed into the RCU every projector without exception will listen to the commands given by this RCU Ho
5. Ce Elo GGG EE Se 8 O 5 Professional VCR Audio amplifier GENERAL ACCESS SHARPNESS TINT 6 COLOR 4 BRIGHTNESS 2 CONTRAST Enter ADJUST Select with 4 J OI et then lt ENTER gt lt EXIT gt to return Fok 30o 90000 bos GH T i 3 O O Be Ge e 0 Professional VCR Audio amplifier with Tri level sync 3 5 Connections R Y Y B Y 3S or R Y Y3s B Y input selection a Press digit button 6 on the RCU or b With the local keypad to gain access to the local keypad see Local keypad in chapter Location and function of controls Press ADJUST key the General access menu is displayed on the screen Use the control disk to highlight 6 Press ENTER to select the highlighted source GENERAL ACCESS SHARPNESS TINT COLOR BRIGHTNESS CONTRAST 5 B 3 4 1 2 Enter ADJUST Select with 4 y OF et then lt ENTER gt
6. Corrects the keystone geometry correction of the vert lines the left side II Adjust the next alignments until the vertical lines are straight R a To enter an alignment push the control disk up or down to highlight a function and press ENTER to activate this function vee Press EXIT to return Corrects the tilting of the vertical he image i hy LEFT RIGHT E W af de E V CENTERLINE BOW V CENTERLINE SKEW RIGHT BOW RaT BON Corrects for curvature of the vertical lines on LEFT KEYSTONE ll TT Select with 4 or t R g then lt ENTER gt lt EXIT gt to return S E i PLA P I il 1 ee Corrects the keystone geometry correction o the right side I I TEE ut NA l Corrects for curvature of the vertical lines on the left side Ir UU IN LEAN IBA vr ery Io mme d Correct by pushing Correct by pushing the control disk to the the control disk to right the left 5975977 BAR CODATA 708 260597 M 6 7 Random Access Adjustment Mode Top Bottom north south Adjustments Top Bottom and center adjustments affect only the horizontal lines of the projected image To start up the Top Bottom and center corrections follow the next procedure Push the control disk up or down to highlight TOP BOTTOM N S on the geometry menu and then press EN
7. 4 8 Controlling Picture controls The picture controls can be adjusted with a The RCU The control keys are located on the left side of the key panel of the RCU and indicated with the name of the control and an icon When an image control is pressed a text box with bar scale and the function name of the control e g brightness appears on the screen only if text is ON The length of the bar scale indicates the current memorized setting for this source The bar scale changes as the or buttons of the control are pressed b The local keypad All controls are hidden in the General access menu Press ADJUST to display the General access menu Use the control disk to highlight the desired analog control and press ENTER to select m O ADJUST EXIT gt eng STANDBY ENTER GENERAL ACCESS SHARPNESS TINT 5 6 COLOR 3 4 BRIGHTNESS 1 2 CONTRAST Enter ADJUST Select with f 4 OF et then lt ENTER gt lt EXIT gt to return When a picture control is selected a text box with bar scale and the function name of the control e g brightness appear on the screen The length of the bar scale indicates the current memorized setting for this source percentage scale The bar scale
8. Safety Instructions SAFETY INSTRUCTIONS WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION FCC STATEMENT This equipment has been tested and found to comply with the limits of a class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated ina commercial environment This equipment generates uses and can radiate radio frequency energy ana if not installed and used in accordance with the instruction manual may cause harmful interference to radio commu nications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Note The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022 All the safety and operating instructions should be read before using this unit The safety and operating instructions manual should be retained for future reference All warnings on the equipment and in the documentation manuals should be adhered to All instructions for operating and use of this equipment must be followed precisely On safety 1 This product should be operated from an AC power source This projector may be connected to an IT power system Oper
9. Highlight Memory management by pushing the control disk up or down and press ENTER to display the memory management menu Within the memory management menu the following items can be consultated or executed copy a block delete a block delete all blocks all settings to midposition R amp B convergence to mid Gr convergence mid only if green convergence is available 5975977 BARCODATA 708 260597 Service Mode PROJECTOR SET UP IDENTIFICATION TOTAL RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE operating BARCO LOGO gt i z T BARCO LOGO SIZE SMALL BACKGROUND ON ORBITTING ON You can move the logo on the screen using the arrow keys WARNING continuous use of the BARCO logo damages the RED CRT Select with 4 or t lt ENTER gt to toggle lt EXIT gt to return SERVICE MODE PROJECTOR SET UP COMMON SETTINGS I2C DIAGNOSTICS MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R amp B CONVERGENCE MID GR CONVERGENCE MID Select with or f then lt ENTER gt lt EXIT gt to return 7 5 Service Mode Copy a block The copy a block function copies the settings of a selected block into the active block Highlight copy a block with the control disk and press ENTER ENTER will select the highlig
10. SHARPNESS TINT COLOR BRIGHTNESS CONTRAST quit ADJUST Select with 4 4 4m OF my then lt ENTER gt lt EXIT gt to return AN ADJUSTMENT MODE Select a path from below GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with f or 4 then lt ENTER gt lt EXIT gt to return Safety Instructions RANDOM ACCESS Random Access should be selected if the user intends to make only a few adjustments SERVICE Service should be selected if the user intends to delete blocks change password or apply information IRIS This selection will only be available when the autoconvergence unit IRIS is connected to the projector While in Guided or Random Access adjustment Mode the user may use an external source an internally generated genlocked pattern or an internally generated multifrequency cross hatch pattern as a setup pattern Warning during the start up of the installation mode WARNING RISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO AND TO BE PERFORMED ONLY BY BARCO PERSONNEL OR BARCO AUTHORIZED DEALERS IF QUALIFIED PRESS lt ENTER gt TO CONTINUE OR IF NOT lt EXIT gt TO RETURN
11. GREEN BLUE RED AND GREEN BLUE AND GREEN RED AND BLUE Select with 4 or t lt ENTER gt to accept lt EXIT gt to return ue ind 5975977 BARCODATA 708 260597 Geometry Adjustments Random Access Adjustment Mode The geometry adjustments have to be done only on the green image These adjustments are automatically implemented for the other color images Left right EW and Top Bottom Corrections Blanking Horizontal Amplitude Vertical Amplitude Vertical Linearity and Horizontal Phase Highlight GEOMETRY by pushing the control disk up or down and press ENTER to display the geometry menu ENTER will display Geometry menu EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu ADJUST returns to operational mode Within the Geometry Adjustment menu the following adjustments are available Horizontal Phase not for internal pattern Raster Shift Left Right Corrections Top Bottom Corrections Horizontal Size Vertical Linearity Vertical Size Blanking The convergence corrections are disabled during geometry correc tions The blanking corrections are only enabled during the blanking adjustments Horizontal Phase Adjustment Push the control disk up or down to highlight H PHASE on Geometry menu and then press ENTER Note No horizontal phase adjustment is available on the internal pattern For external sources If the raster shift
12. SS Select with 4 or t then lt ENTER gt lt EXIT gt to return 5975977 BARCODATA 708 280597 Common Settings Highlight Common settings by pushing the control disk up or down and press ENTER to display the common settings menu Within the common settings menu the following items can be set up or executed G2 adjustment CRT run in cycle Projector warm up G2 Adjustment Item is password protected Highlight G2 adjust with the control disk and press ENTER to continue A safety notice will be displayed on the screen as it is necessary to open the top cover to adjust the G2 ENTER selects the G2 adjustment N EXIT returns to the Common settings menu QUEST returns to the Operational mode J G2 adjustment should be performed by BARCO personnel or BARCO authorized dealers If you are qualified press ENTER to continue If not qualified press EXIT to return to the Common settings menu Further description of the G2 adjustment is given in the Installation manual CRT run in cycle The CRT run in cycle option can only be activated when memory blocks on an internal pattern are available When one or more such blocks are available a flashing white image 5sec on 5 sec off is generated and that for 5 min on the first internal block In the next 5 min a second internal block will be used to generate the flashing white image The image will also be shifted in a vertical way to prevent
13. lt EXIT gt to return Connecting a computer e g IBM PC or compatible Apple Macintosh to the RS232 input of the projector The projector has a RS232 port that allows it to communicate with a computer Applications remote control and data communications a remote control easy adjustment of the projector via IBM PC or compatible or MAC connection allow storage of multiple projector configurations and set ups wide range of control possibilities address range from 0 to 255 b data communications sending data to the projector or copying the data from the projector to a hard memory device Peripheral equipment Connecting a RCVDS 05 switcher to the projector Up to 10 inputs 20 inputs when video and S video with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules Serial communication with the projector Remote control buttons on the RCVDS to control the projector source selection and analog settings The selected source number will be displayed on a 2 digit display and the selected input modules will be indicated with a LED on the rear For more information about the use of the RCVDS 05 consult the Owner s Manual order number R5975765 Connecting a VS05 switcher to the projector The VS05 can switch up to 5 Composite Video sources 3 S Video Sources and
14. INTERNAL PATTERN i La RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE PICTURE TUNING COLOR BALANCE SYNC FAST LINE DOUBLER ON Select with 4 or t lt ENTER gt to accept lt EXIT gt to return 3 3 Connections Connecting a RGB Analog source with composite sync RGB analog input terminals with composite sync input or with sync on green The projector detects automatically where the sync signal is located Always use an interface when a computer and local monitor have to be connected to the projector Examples of interfaces which can be applied Universal analog interface RGB 120 MHz Analog Interface Multifunctional Analog Interface Kit MAGIK VGA interface MAC interface RGBS or RGsB input selection a Press digit button 3 on the RCU or b With the local keypad to gain access to the local keypad see Local keypad in chapter Location and function of controls Press ADJUST key the General access menu is displayed on the screen Use the control disk to highlight 3 R9826100 R9826570 230V R9828120 230V R9828129 120V R9828070 230V R9828079 120V R9828050 230V R9828059 120V Press ENTER to select the highlighted source Connecting a RGB Analog source with Tri level sync RGB analog input terminals with Tri level sync input or with Tri level sync on green The projector detects automatically where the
15. TIME CHANGE PASSWORD CHANGE BAUDRATE 4i Select with 4 or t then lt ENTER gt lt EXIT gt to return CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS POWER UP MODE H operating BARCO LOGO UE 5975977 BARCODATA 708 280597 BARCO_logo The BARCO logo can be added to the image in overlay or in background on any place on the screen To add the BARCO logo or to change a setting in the BARCO logo menu highlight BARCO logo by pushing the control disk up or down and press ENTER to select WARNING Continuous use of the BARCO logo damages the RED CRT ENTER displays the BARCO logo menu p EAT returns to the Service menu BW The BARCO logo menu will be displayed on the screen Within this menu four toggle settings are available Mode ON OFF ON BARCO logo will be displayed on the screen To position the logo on the screen push the control disk up down to the left or to the right until the desired position is reached OFF No BARCO logo displayed on the screen Size SMALL LARGE SMALL Small BARCO logo will be displayed if mode is on LARGE Large double size BARCO logo will be displayed if mode is on Background ON OFF ON BARCO logo will be displayed on a black background BARCO OFF BARCO logo will be displayed without any background BARCO Orbiting ON OFF ON on the BARCO logo will orbit around it axis OFF no orbit of the BARCO logo Memory management
16. a D9 D9 communication cable To connect an IBM PC or compatible to the projector To connect a RCVDS05 to the projector To connect a IR receiver to the RCVDSO5 to the projector To be used as extension cable for all other adapter cables Available length 5 m 16ft order number R982770 15 m 50ft order number R9827560 and 30 m 100ft order number R9827570 b Din Mini8 D9 adapter cable To connect a Macintosh computer to the RETROGRAPHICS 808s Available length 1 m 3 2 ft order number R9827640 c D25 D9 adapter cable To connect a workstation to the RETROGRAPHICS 808s Available length 1 m 3 2 ft order number R9827630 d 5 BNC to 5 BNC cable To connect an analog source to the BNC input of the projector Available lenght 60 cm order number R9828260 150 cm order number R9828261 5 m order number R9828262 15 m order number R9828263 Orbiting Kit Static pictures are very often shown on large screen projectors especially in process control and presentation applications Due to the fact that the same picture information is shown for a long period inthe same place picture tubes can be damaged by local burn in To reduce this problem a special Orbiting circuit is available which moves the picture very slowly around a predefined screen area The cycle time is very long to make the movement of the projected image imperceptible The use of the orbiting kit is described in appendix A in the installa
17. a CRT burn in To quit the CRT run in cycle option press EXIT Highlight CRT run in cycle with the control disk and press ENTER to start ENTER selects the CRT run in cycle option K NR returns to the Path Selection main menu L 5975977 BARCODATA 708 260597 Service Mode SERVICE MODE PROJECTOR SET UP MEMORY MANAGEMENT 12C DIAGNOSTICS Select with or f then lt ENTER gt lt EXIT gt to return COMMON SETTINGS G2 ADJUSTMENT CRT RUN IN CYCLE PROJECTOR WARM UP Select with y or t then lt ENTER gt lt EXIT gt to return COMMON SETTINGS CRT RUN IN CYCLE PROJECTOR WARM UP CRT DRIVE MODE Select with 4 or t then lt ENTER gt lt EXIT gt to return SAFETY NOTICE RISK OF ELECTRICAL SHOCK G2 ADJUSTMENT SHOULD BE PERFORMED BY BARCO PERSONNEL OR BARCO AUTHORIZED DEALERS IF QUALIFIED PRESS lt ENTER gt TO CONTINUE OR IF NOT lt EXIT gt TO RETURN COMMON SETTINGS PROJECTOR WARM UP CRT DRIVE MODE Select with 4 or t then lt ENTER gt lt EXIT gt to return 7 9 Service Mode If a memory block adjusted on an internal pattern is available the CRT run in cycle will start when pressing ENTER If no such a block is available the projector cannot run the CRT run in option and leaves the adjustment mode If you still want to run CRT run in cycle create first a memory block on an internal pattern and restar
18. assign an additional adjustment block to a source This additional adjust ment block may contain different geometry and convergence settings sync fast slow positions and enhanced blue on off settings The relationship between source numbers 0 9 and 90 99 projector with RCVDS or 1 5and 91 95 stand alone projector is shown in the diagram below The alternate adjustment block for sources 0 9 projector with RCVDS or 1 5 stand alone projector is activated by selecting the corresponding source number 0 9 projector with RCVDS or 1 5 stand alone projector Once this source number is selected the alternate block of adjustment data is in use and may be modified via the adjust mode of the projector The alternate adjustment block is automatically stored Follow the steps below to create a second adjustment block for a source between 0 and 9 1 Select the source between 0 and 9 that the second adjustment block is to be created for 5975977 BARCODATA 708 260197 source number 0 Block header A source input 0 source number 90 Block header A differ ent analog settings source number 1 Block header B source input 1 source number 91 Block header B differ ent analog settings source number 2 Block header C source input 2 Block header C differ ent analog settings source number 92 source number 9 Block header J source input 9 source number 99 Block header J differ ent analog settings 2 Sel
19. into the lenses to perform these adjustments To avoid eye discomfort while looking into the lenses reduce the contrast and gradually increase the brightness level until the raster becomes visible on the face of the CRT ENTER will select green raster shift adjustment EXIT returns to random access adjustment mode menu Warning In order to ensure maximum CRT longevity and to avoid CRT damage do not shift the raster outside the phosphor area of the CRT To start the adjustment use the control disk to highlight Raster shift and press ENTER to display the green raster on the phosphor GEOMETRY H PHASE LEFT RIGHT E W TOP BOTTOM N S m SIZE m V LINEARITY Ry j BLANKING J COARSE SHIFT GREEN HORIZONTAL GREEN VERTICAL RED VERTICAL BLUE VERTICAL Select with 4 or t then lt ENTER gt lt EXIT gt to return forbidden area projected raster m crt faceplate border phosphor border correct raster position wrong raster positions Press EXIT to return to the Geometry menu Note Horizontal and Vertical shifts for Red and Blue should end up with a setting close to 50 If these settings are significantly greater or lesser than 50 contact a BARCO authorized service technician 233 6 6 5975977 BARCODATA 708 260597 Random Access Adjustment Mode Left Right ea
20. right to adjust the blue gain A bar scale indicates the amount of adjustment Select custom black balance with the control disk and press ENTER to start the adjustment Push the control disk up or down to adjust the red cut off and push the control disk to the left or to the right to adjust the blue cut off When the color balance is adjusted select continue by pushing the control disk up or down and press ENTER Sync Fast Slow Adjustment The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image Highlight SYNC with the control disk and press ENTER to toggle between FAST and SLOW Note SYNC is normally used in the SLOW position The FAST position is used to compensate for unsteady sync pulses from older video playback equipment Hint when the line doubler feature is ON active toggle the sync to FAST ENTER will toggle Sync between FAST and SLOW EXIT will return to the Randam Access Adjustment menu 5975977 BARCODATA 708 260597 RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE COLOR SELECT Select with or t then lt ENTER gt lt EXIT gt to return PICTURE TUNING COLOR BALANCE SYNC FAST PORT 2 S VIDEO PEAKING ON LINE DOUBLER ON Select with 4 or t lt ENTER gt to accept lt EXIT gt to return PICTURE TUNING COLOR BALANCE SYNC FAST PEAKING ON LINE DOUBLER ON COLOR
21. side in the remote control and the other side in the connector on the rear of the projector labelled remote Projector Control software The software is user friendly and makes full use of mouse control pull down menus and dialog boxes Two main applications are available with this software remote control and transfering and receiving data of projector settings Remote Control Simulation Advantage address range 0 to 255 Adjustment Data Where can it be located when a IBM PC or compatible or MAC or Workstation is connected Hard memory device with files of settings The contents of the local memory of the computer The contents of the projector 5975977 BARCODATA 708 260597 Options RCVDS 05 Source Selector An optional RCVDS05 makes it possible to connect up to 20 sources to the projector When RCVDS s are linked via the expansion module even 90 inputs can be connected to the projector The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the rear Order Numbers RCVDS 05 110V 9827888 9827889 9827880 9827881 220V VS05 Switcher The VSO5 is a versatile Video and HDTV source selector for all BARCO s digitally controlled large screen projectors It offers the possibility to connect and switch up to 5 different Video sources 3 different S Video sources and 1 RGB Analog source to a BARCO pr
22. sync signal is located 3 4 GENERAL ACCESS SHARPNESS TINT 5 COLOR 4 BRIGHTNESS 1 2 CONTRAST Enter ADJUST Select with 4 ers then lt ENTER gt lt EXIT gt to return o o E o 2 PEE e 0 VCR HDTV player Audio amplifier 5975977 BARCODATA 708 260597 RGB3S or RG3sB input selection a Press digit button 4 on the RCU or b With the local keypad to gain access to the local keypad see Local keypad in chapter Location and function of controls Press ADJUST key the General access menu is displayed on the screen Use the control disk to highlight 4 Press ENTER to select the highlighted source Connecting a Component source R Y Y B Y analog input terminals with sync input or with sync on the luminance Y input The projector detects automatically where the sync signal is located Connections GENERAL ACCESS SHARPNESS TINT
23. 08 OWNER S MANUAL BARCO BARCO PROJECTION SYSTEMS BARCO hs R9002120 OWNER S MANUAL Date Art No 260597 R5975977 Due to constant research the information in this manual is subject to change without notice Produced by BARCO NV May 1997 All rights reserved Trademarks are the rights of their respective owners BARCO nv Projection Systems Noordlaan 5 B 8520 Kuurne Belgium Printed in Belgium Table of Contents TABLE OF CONTENTS TABLE OF CONTENTS tarta 1 SAFETY INSTRUC TIONS EE 1 1 STEE MA o i a a i ae aaa bh EE 1 1 ll EE e NEE 1 2 OMS a ee E EE i va shite EG 1 2 ON ClOANING ri A ae aa A a in a RA 1 2 lee le DEE 1 2 OA ilumNatO M a A aa ae a a a a a a a 1 2 LOCATION AND FUNCTION OF CONTROLS kaaa 2 1 Rear Panel Kuul ue ee VE 2 1 Front Panel Terminology vs An KA Oo EE ERE 2 1 Gontrol panelterminology za ivi didi Ai eee es 2 2 CONNECT O NS a 3 1 SWITCHING ON oa td a da a 3 1 Signal input connection to the projector 3 1 Power mains Cord connection REENEN 3 1 Connecting a Composite Video SOUICE aeaa aaa aaa 3 2 Connecting a S Video or Video source to Port 3 3 3 Connecting a RGB Analog source with composite em 3 4 Connecting a RGB Analog source with Tri level eme 3 4 Connecting a Component SQUICE 0aaaa aaa 3 5 Connecting a Component source with Tri level Sync kaaa 3 5 Connecting a computer e g IBM PC or compatible Apple Macintosh to the RS232 input of
24. 1 RGB analog or component Video source to the projector In addition the audio signal proper to the source can be switched to an audio amplifier Order number R9827890 For more information about the use of the VS05 consult the Owner s Manual order number R5975245 3 6 RS232 connection Connecting an IR Remote Receiver to the projector This infra red receiver unit makes it possible to control the projector from another room There is acommunication line cable between the IR receiver and the projector or the RCVDS The infrared control information from the Remote Control Unit is sent to the IR Remote Receiver The IR Remote Receiver 800 displays the selected source on a 7 segment display Order number R9827515 5975977 BARCODATA 708 260597 Controlling CONTROLLING Caution Do not display a stationary image with full brightness and contrast for longer than 20 min otherwise you risk damage to the CRT s Battery installation in the RCU A new battery is delivered inside the plastic bag with the power cord Before using the RCU install first the battery Remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU Lift up the top side
25. 5 Raster Shift Adjustment resi A ba aaa aN el de A Aha eh even 6 6 Left Right east west Adjustments ec ceeeee aaa 6 7 Top Bottom north south Adjustments AAA 6 8 SIZE Adjustment g oi az end a An dia tasta iban 6 9 Vertical Linearity Adjustment 0000 aaa aan 6 9 Banking TEE 6 10 Convergence Adjustment c oooocccccnnncccccnccccnnnnonccnn nan cc nana cnn mens 6 11 ERVICE MODE E sta 7 1 Starting up the Service mode 7 1 Overview flowchart Service mode 000 aa 7 1 Project n Setup iia iaa tias 7 2 euer le Le EE EE E 7 2 Total RUM TIMO a A eA een cd iaa 7 3 Change password zem e A A AA A ee 7 3 Ghange an UE EE 7 3 Change Projector Address siia aaa 7 4 El leie EE 7 4 Power Up MOUS arca 7 4 BARCO NOG Le EE 7 5 Memory manageme amp nt 0000 cael eden the ernie tei ent 7 5 Gopa DIOCK EE 7 6 Deletion of Hocks iii AA ee e lee ai avid 7 6 Deleting block by DOCK EE 7 6 Reie Hee EE 7 7 All settings to MIG POSIUION o aeeie dci ind dd eet 7 7 Undo all settings to midoes NENNEN o AER AEA EL dee ee 7 7 R amp B CONVETIONCO TEE 7 8 Undo R amp B convergence mid aaa 7 8 Green convergence Mid WEE 7 8 Undo green convergence Mids EE 7 8 COMMON lee EE 7 9 G2 Adjustment Ad 7 9 CATA A e EE 7 9 Projector War UP ii ce eee eee aire ce aii eee re 7 10 GRIT Drive Mode ricino a rad 7 10 I2C DidQnOSstieS ii eee Ge o eel tel ae ated ae etl baie 7 11 L 5975977 BARCODATA 708 260597 Table of Contents MESSAGES WARNINGS AN
26. A 708 260597 BEBEK p 5 Location and Function of Controls TEXT when adjusting one of the image controls during a meeting the displayed bar scale can be removed by pressing TEXT key first To re display the bar scale on the screen press TEXT key again TEXT key is only active in operational mode When TEXT is off no warning message will be displayed ENTER to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode EXIT to leave the adjustment mode or to scroll upwards when in the adjustment mode Control disk to make menu selections when in the adjustment mode Also allows to increment or decrement an adjustment in the adjustment mode control disk up up arrow in the menus control disk down down arrow in the menus control disk to the right arrow to the right on the menus control disk to the left arrow to the left on the menus RC operating indication lights up when a button on the remote control is pressed This is a visual indicator to check the operation of the remote control Location and Function of Controls 2 4 5975977 BARCODATA 708 260597 CONNECTIONS Power mains cord connection Use the supplied power cord to connect your projector to the wall outlet Plug the female power connector into the male connector at the front of the projector Switching on off The projector is switched ON and OFF using the power mains switch O
27. ARCODATA 708 260597 Random access adjustment mode selection menu This is the main menu for the Random Access adjustment mode Through this menu the following adjustments and features are accessible Picture Tuning Enhanced Blue only for RGB Sync slow fast video s video Color Balance Geometry Convergence Color select And also Orbiting Contrast modulation and Soft Edge if these options are installed Picture Tuning Highlight Picture tuning by pushing the control disk up or down and press ENTER The Picture tuning menu will be displayed Depending on the input source the Picture tuning menu will display different items Color Balance Sync slow fast Line doubler Port 2 S Video Peaking Color Balance The Color Balance function is used to select or adjust the color temperature of white used by the projector The Color Balance can be adjusted on two different ways fixed color balance You have the choice between 3200 K reddish 4900 K 6500 K white or 9300 K bluish Custom white and black balance Fixed Color Balance Highlight one of the 4 preprogrammed color temperatures with the control disk and press ENTER to display the desired color balance Custom Color Balance Select custom white balance by pushing the control disk up or down and press ENTER to start the adjustment Push the control disk up or down to adjust the red gain and push the control disk to the left or to the
28. ATION TOTAL RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS 1 CHANGE BAUDRATE a POWER UP MODE operating GO ES BARCO DATA 708 Proj address 001 Soft Version 6 00 Config Ceiling Front Baudrate PC 9600 Text ON Serial No 103589552 5975977 BARCODATA 708 280597 Total Run Time Highlight Total Run Time with the control disk and press ENTER to display the amount of time the projector has played since its first start up at the factory ENTER gives the selected item 2 EXIT returns to the Service mode menu ADJUST returns to the Operational mode A Note all projectors leave the factory after a burn in period of approximately 100 hours Change password This item is password protected Highlight Change Password with the control disk and press ENTER ENTER will display the selected item N EXIT will return to the Path Selection main menu KADJUST will return to the Operational mode pr The current password is displayed The new password must consist of 4 digits between 0 and 9 Push the control disk to the left or to the right to select the digits to be changed Use the numeric keys to enter the new digits Press ENTER to save the new password Before saving the new password a confirmation screen will be displayed Press EXIT to return to the Projector Set up menu without saving the new password When the displayed passwor
29. BALANCE FIXED COLOR BALANCE 3200 4900 6500 9300 CUSTOM WHITE BALANCE CUSTOM BLACK BALANCE Select with arrow keys then lt ENTER gt You can adjust red with Y or f Blue with mm Or lt lt EXIT gt to return PICTURE TUNING COLOR BALANCE ISYNC FAS LINE DOUBLER ON Select with or f lt ENTER gt to accept lt EXIT gt to return Random Access Adjustment Mode Random Access Adjustment Mode Line Doubler option Line doubling is only possible for Video S Video Component Video images on standard line frequency and RGB signals on 15 kHz To eliminate the video line patterns and to improve the image stability the line doubler has to be switched on The line doubler is default set in the ON position when starting up for the first time The setting of the line doubler will be saved together with the source number Each time this source number is selected the last saved version will be loaded Highlight Line Doubler with the control disk and press ENTER to toggle between ON active and OFF non active EXIT will return to the random access selection menu Port 2 S Video Video Port 2 can be used as Video or S Video input Highlight Port 2 by pushing the control disk up or down and press ENTER to toggle between Video and S Video Peaking Peaking improves the contours in an projected image Highlight PEAKING by pushing the control disk up or down and press ENTER to toggle the pea
30. C number mod name C200 DECODER Scroll with gt or dem then lt ENTER gt lt EXIT gt to return 7 11 Service Mode 5975977 BARCODATA 708 280597 INPUT 01 Fh 15 6 kHz Fv 050 Hz SOURCE 01 enter password XXXX text on text off PROJECTOR ADDRESS 003 WARNING input not available WARNING source not available WARNING invalid key entry When selecting a new source in formation about this source will be displayed on the screen Source number horizontal and vertical fre quencies of the displayed source Announcement of the selected source Message to enter your password Password contains 4 digits These messages will be displayed on the screen when pushing the TEXT key Text ON the bar scale indication will be enabled during the change of an analog control inthe operational mode all warnings and failures will be displayed Text OFF the bar scale indication will be disabled during the change of an analog control in the opera tional mode all warnings and failures will not be displayed Indication of the projector address when activating the ADDRESS button on the RCU with a pencil or other small object When using the projector with the RCVDS this warning will be dis played when selecting an input slot ofan RCVDS where the input board is missing The input is a val
31. D FAILURES aaa 8 1 OP TIN So 9 1 IR Receiver BOO cia dt Aides 9 1 Hardwired ROW ege eer EA AA AAA AA ieee aed 9 1 Projector Control software 0aaaa akv 9 1 RCVDS 05 Source Selector ia dini 9 1 MES EE 9 1 IRIS 2 Auto Convergence System 00 akan 9 1 E ler Le EE 9 2 Adapter and communication Cables oooonoooccccncccnonancconcnnnnncncnnanonononnnnncnnnnnn corn nn nn rn nnnnnn nn n nn nn rr nnnnnnnnn 9 2 DDN E 9 2 Line Doubler Killian A i in i Se DA 9 2 Ceiling Mount COMBO etica ll ancora 9 2 Soft isdge matching Kitano 9 2 Contrast modulatiori taa 9 2 APPENDIX A ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90 99 A 1 Adjustment Blocks Memory blocks ooooooccccccccococococanonoconananannnnnnncncnanano nono nn cnn nnnnnnn conc nn arc rnnnnnn nn cnn A 1 SOUrGE NUMBEFS 9O 99 ii efi A 1 5975977 BAR CODAT A 708 260597 __ L Table of Contents 5975977 BARCODATA 708 260597 Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950 UL 1950 and CSA C22 2 No 950 which are the safety standards of information technology equipment including electrical business equipment These safety standards impose important requirements on the use of safety critical components materials and isolation in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts Safety stand
32. N SETUP PATTERN SELECTION H CENTERLINE BOW H CENTERLINE SKEW TOP KEYSTONE TOP BOTTOM N S TOP BOW BOTTOM KEYSTONE BOTTOM BOW M PICTURE TUNING SIDE KEYSTONE SIZE SEAGULL CORRECTION m VER LINEARITY m TOP BOW BOTTOM KEYSTONE BOTTOM BOW CONVERGENCE SEAGULL CORRECTION COLOR SELECT 5975977 BARCODATA 708 260597 _____ 6 1 BLANKING Random Access Adjustment Mode Selecting Setup Pattern If an external source is connected to the projector this menu will be displayed Push the control disk up or down to highlight the desired setup pattern and then press ENTER Genlocked pattern internally generated cross hatch pattern locked on the external source Internal pattern internally generated cross hatch pattern and locked on internal generated sync signals No external source necessary ENTER continues to Random Access Adjustment Mode or Internal Pattern Selection EXIT returns to Path Selection menu ADJUST returns to Operational mode If no external source is connected to the projector the internal cross hatch pattern menu will be displayed Note The menus in this manual are created for an external so
33. N OFF Pressed ON Not pressed OFF The projector can start now in the operational mode image displayed or in the stand by mode depending on the position ofthe power up dip switch onthe controller unit This DIP switch is set during installation by a qualified technician If you want to change this start up mode call a qualified technician Signal input connection to the projector Composite Video S Video RGBS or RGsB RGB3S or RG3sB R Y Y B Y S or R Y Ys B Y component input R Y Y B Y 3S or R Y Y3s B Y component input If the line double feature is built in this feature is available via a software on off toggle Connections la sg Bi OFF o iz m e FREQ 6080 See installation instructions before connecting to the supply V NOM 120 230 Volt 1 IMAX 5 2 5 AMP OFF ON FREQ 60 50 Hz 7 N a ml Leds on the front plate of the projector ANOO If the line double feature is built in this feature is available for component video signals on standard frequency via software on off toggle M I COCOOCO0O0O000 bRERSESY ESSE lt 2 eO7 lt 89 30 SE g g Dez lt Z 2 m TI 3 D 5975977 BARCODATA 708 260597 Connections Source No Projector input Pre
34. NERATED FOR 20 MINUTES AT POWER UP AFTER THIS PROCEDURE THE PROJECTOR IS READY TO PERFORM IN OPTIMUM COI N NDITIOI TOGGLE OPTION ON OR OFF with lt ENTER gt lt EXIT gt to return S COMMON SETTINGS G2 ADJUSTMENT CRT RUN IN CYCLE Pigs T DRIVI WARM UP CRT DRIVE MDOE CRT DRIVE MODE NORMAL ECONOMIC TEMPORARY BOOST PERMANENT BOOST WARNING permanent boost mode reduces the lifetime of the CRT s Select with or t then lt ENTER gt lt EXIT gt to return 5975977 BARCODATA 708 280597 A warning permanent BOOST mode in use will be displayed to inform the user When text is on this warning will be repeated every time a new source is selected 12C Diagnostics Highlights I2C Diagnostics by pushing the control disk up or down and press ENTER The 12C diagnostics menu gives an overview of the 12C failures inside the projector To scroll through the failure list push the control disk up or down The 12C address IC number and module name will be given in I2C diagnostic menu When no errors are detected the following message will appear on the screen No errors on i2c bus detected 5975977 BARCODATA 708 260597 Service Mode WARNING PERMANENT BOOST MODE IN USE SERVICE MODE PROJECTOR SET UP et MEMORY MANAGEMEN COMMON SETTINGS i addr 48H I2C DIAGNOSTICS Failures
35. R Use the control disk to highlight the desired source number Push the control disk up or down to move the cursor up and down push the GENERAL ACCESS SHARPNESS TINT 5 6 COLOR 3 4 BRIGHTNESS 1 2 CONTRAST Enter ADJUST Select with Tt OF et then lt ENTER gt lt EXIT gt to return 5975977 BARCODATA 708 260597 Controlling control disk to the left or to the right to move the cursor to the left and to the right Press ENTER to confirm your selection When a valid and available source is selected there will be informa tion displayed on the screen about that source This information includes Source number Horizontal frequency Vertical frequency When the entry is a non valid source number a warning appears on the screen input not available WARNING input not available When a valid source number is selected the projector will display this source or it will wait on the selected source number until the source becomes available A message source not available will be dis played for a short time WARNING source not available
36. RE IRIS commu nication error WAIT starting up IRIS FAN FAILED Projector will switch off 8 2 Serial communication error be tween the RCVDS and the projec tor Communication error between IRIS 800 and the projector Call a quali fied service technician Message during the start up of the IRIS Message will disappear when the IRIS is ready to accept com mands Message when one of the fans are not working anymore Projector switches to stand by 5975977 BARCODATA 708 260597 OPTIONS IR Receiver 800 This infrared receiver unit makes it possible to control the projector from another room There is a communication line with cable between the IR receiver and the projector or the RCVDSO5 The control information from the RCU can now be sent to this IR receiver The IR receiver 800 displays the selected source on a 7 segment display Order number R9827515 Hardwired RCU The control signals from the RCU can be sent to the projector via a wired connection shield conductor Preparing your remote cable Use a shielded cable with a maximum length of 100 m and two mini jack 3 5 mm connectors order number R3131991 Peel back the vinyl covering of the cable on both sides and twist the wire core Solder a jack plug as shown in drawing above to each end of the cable shield ground conductor data information When the cable is ready plug one
37. TER Only the green image is displayed while making top botton adjust ments The red and blue images will automatically be corrected in the same manner Convergence corrections are automatically disabled for the duration of these adjustments The following adjustments can be executed Horizontal centerline bow Horizontal centerline skew Top bow Top keystone Bottom bow Bottom keystone All adjustment are indicated on the screen with the function name a bar scale and a number between 0 and 100 Adjust the next alignments until the vertical lines are straight To enter an alignment push the control disk up or down to highlight a function and press ENTER to activate this function Press EXIT to return fan TOP BOTTOM H CENTERLINE BOW H CENTERLINE SKEW TOP BOW TOP KEYSTONE BOTTOM BOW BOTTOM KEYSTONE Select with 4 or t then lt ENTER gt lt EXIT gt to return 6 8 GEOMETRY H PHASE RASTER SHIFT V LINEARITY BLANKING LEFT RIGHT E W TOP BOTTOM N S SIZE LEDS H CENTERLINE BOW H CENTERLINE SKEW TOP KEYSTONE TOP BOW BOTTOM KEYSTONE BOTTOM BOW Ry i 2 Select with 4 or t then lt ENTER gt lt EXIT gt to return TOP BOTTOM N S middle of the image Corrects for curvature of the h orizontal lines in the of the image Corrects the tilting of the horizontal lines in the mid
38. WITCH press the switch to turn the projector ON Depending on the hardware set up of the projector during installation the projector switches to standby or to operational mode If in standby the standby led in the autodiagnosisdisplay lights up 5975977 BARCODATA 708 260597 Se Q g Z S 3 2 3 s O POWER MAINS INPUT Connect the supplied ac power mains cord here and to wall the outlet IR SENSOR receiver for control signals transmitted from the RCU700 2 1 Location and Function of Controls Control panel terminology a The local keypad Gaining access The local keypad is covered by a door on which the projector logo is screened To open this door push as indicated on next drawing and turn it to the front side of the projector b RCU control panel terminology This remote control includes a battery powered infrared IR transmitter that allows the user to control the projector remotely This remote control is used for source selection control adaptation and set up It includes automatic storing of picture controls Brightness Sharpness picture geometry adjustments convergence adjustments Other functions of the remote control are switching between standby and operational modes switching to pause blanked picture full power for immediate restarting direct access to all connec
39. ards also impose limits to the internal and external temperature rises radiation levels mechanical stability and strength enclosure construction and protection against the risk of fire Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment s normal operation fails INSTALLATION INSTRUCTIONS Before operating this equipment please read this manual thoroughly and retain it for future reference Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers OWNER S RECORD The part number and serial number are located at the back side of the projector Record these numbers in the spaces provided below Refer to them whenever you call upon your BARCO dealer regarding this product PART NUMBER SER NUMBER DEALER RISK OF ELECTRIC SHOCK DO NOT OPEN D CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons The exclamation point within a triangle is in tended to tell the user that important operating and or servicing instructions are included in the technical documentation for this equipment 5975977 BARCODATA 708 260597
40. ating AC power voltage of the projector BARCODATA 708 Art No R9002120 230V AC Consult your dealer to switch over from 230Vac to 120 Vac or from 120Vac to 230 Vac If you are not sure of the type of AC power available consult your dealer or local power company 2 This product is equipped with a 3 wire grounding plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the purpose of the grounding type plug WARNING FOR THE CUSTOMERS THIS APPARATUS MUST BE GROUNDED EARTHED via the supplied 3 conductor AC power cable If the supplied power cable is not the correct one consult your dealer Safety Instructions A Mains lead Power cord with CEE 7 plug The wires of the mains lead are colored in accordance with the following code Green and yellow Blue Brown earth safety earth neutral line live LINE BROWN NEUTRAL BLUE GROUND YELLOW GREEN B Power cord with ANSI 73 11 plug PETET The wires of the power cord are colored in accordance with the following code Green yellow ground White neutral Black line live LINE BLACK NEUTRAL WHITE GROUND YELLOW GREEN 3 Do not allow anything to rest on the power cord Do not locate this product where persons will walk on the cord To disconnec
41. b with the local keypad Hue O TV tuner e g TVDM40 stereo Audio amplifier for access to the local keypad see Local keypad in chapter Location and function of controls press ADJUST key the General access menu is displayed yen on the screen use the control disk to highlight 7 press ENTER to select the highlighted source GENERAL ACCESS SHARPNESS TINT 5 6 COLOR 3 4 BRIGHTNESS 2 CONTRAST Enter ADJUST Select with 4 4 OI et then lt ENTER gt lt EXIT gt to return 3 2 E 5975977 BARCODATA 708 260597 Connecting a S Video or Video source to port 2 Separate Y luma C chroma signals for higher quality playback of Super VHS signals If a line doubler is built in the default position of this line doubler is ON active the video input signal will be displayed as a non interlaced image improved image stability To enable or to disable this line doubler function enter the adjustment mode and change the position of the ON OFF toggle switch see Picture tuning in chapter Guided adjust ment mode or Random access adjustment mode Input selection a with the RCU press digit button 2 or b with the local keypad for access to the local keypad see Local keypad in chapter Location and function of controls press ADJUST key the General access menu
42. block headers and adjustment settings are permanently removed and cannot be restored All settings to midposition Item is password protected Highlight All settings to midposition with the control disk and press ENTER to set all settings to their midposition A confirmation menu will be displayed first ENTER displays a Confirmation screen N VEST returns to the Service menu y ENTER will set all settings to their midposition EXIT will cancel the operation to set all settings to their midposition Undo all settings to midpos When All settings to midpos is selected all settings are set to their midposition To cancel this action select Undo all settings to midpos by pushing the control disk up or down and press ENTER Undo all settings to Midposition is displayed in the Memory man agement menu in stead off All settings to midposition when this latter is pressed An undo is possible as long as the projector is playing on the same source same adjustment block even when some adjustments as geometry or convergence are already readjusted When undo is presssed all settings are reset to the previous settings 5975977 BARCODATA 708 260597 Service Mode MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK ALL SETTINGS TO MIDPOS R 8 B CONVERGENCE MID GR CONVERGENCE MID DELETE ALL BLOCK m All block will be deleted lt ENTER gt to confirm lt EXIT gt to cancel
43. ce versa push the control stick PROJETOR SETUP D D MEMORY MANAGEMENT forward or backward to select more COMMON SETTINGS 12C DIAGNOSTICS Select with 4 or t then lt ENTER gt lt EXIT gt to return Overview flowchart Service mode IDENTIFICATION TOTAL RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE BARCO LOGO PROJECTOR SET UP COPY A BLOCK SERVICE MODE DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS MEMORY MANAGEMENT R 8 B CONVERGENCE MID GR CONVERGENCE MID G2 ADJUSTMENT CRT RUN IN CYCLE PROJECTOR WARM UP CRT DRIVE MODE COMMON SETTINGS 12C DIAGNOSTICS 5975977 BARC ODATA 708 260597 MMM 71 Service Mode Projector Set up Highlight Projector Set Up by pushing the control disk up or down and press ENTER to display the projector set up menu Within the projector set up menu the fol lowing items can be consultated or set to the desired setting Identification Total run time Change password Change language Change projector address Change baudrate Power up mode BARCO logo Identification Highlight Identification with the control disk and press ENTER ENTER will start the selec
44. changes as the control disk is pushed to the left or to the right MA PF Y E BRIGHTNESS E zz 35 Brightness Control A correct brightness setting is important for good image reproduc tion Adjust the brightness with the button and button RCU or pushing the control disk to the left or to the right local keypad until the darkest parts of the picture appear black 4 4 A bar scale gives a visual indication on the screen of the current brightness setting while pressing on the above indicated buttons If the bar scale is not visible on the screen press TEXT once and retry the above indicated buttons The bar scale increases when pressing on the button higher brightness and decreases when pressing on the button lower brightness Contrast Control A correct contrast setting is important for good image reproduction Adjust the contrast to the level you prefer according to room lighting conditions A bar scale gives a visual indication on the screen of the current contrast setting while pressing the or buttons RCU or pushing the control disk to the left or to the right local keypad If the bar scale is not visible on the screen press TEXT key once and retry the above indicated buttons The bar scale increases when pressing on the button higher contrast and decreases when pressing on the button lower contrast Color Saturation Control Colo
45. d is correct press ENTER to save If not correct press EXIT to cancel the saving E ENTER saves the entered password RK a EXIT returns without saving pi Change Language The Change Language function offers the possibility to change the language of the screen menus to English Spanish French German Highlight Change Language with the control disk and press ENTER ENTER selects the Change language menu ES EXIT returns to the Service menu p Push the control disk up or down to select the desired language and press ENTER to change the language 5975977 BARCODATA 708 260597 IDENTIFICATION PROJECTOR SET UP Service Mode PROJECTOR SET UP IDENTIFICATION OTAL RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE operating BARCO LOGO Select with 4 or t then lt ENTER gt lt EXIT gt to return MANGE RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE 1 POWER UP MODE operating V BARCO LOGO SS PASSWORD Enter new password 0000 CHANGE PASSWORD m Password will be reprogrammed as xxxx lt ENTER gt to confirm lt EXIT gt to cancel PROJECTOR SET UP IDENTIFICATION TOTAL RUN TIME Seene DR HANGE LANGUAGE CHANGE PROJECTOR ADDRESS yO CHANGE BAUDRATE POWER UP MODE operatin
46. digital potentiometers once the source has been selected This set of adjustment data is referred to as an adjustment block An adjustment table is automatically created for a source when the source is first connected to the projector and the Adjustment mode is entered If other sources have already been connected to the projector and geometry and convergence adjustments have been performed on these sources the projector will use Linear Digital Interpolation to create a new block for the new source This block will provide an initial set of adjustments for the new source that have been calculated by the projector from previous experience The projectors memory has the capacity to store 32 adjustment blocks The adjustment block consists of two parts the block header and the data representing the values for all adjustments eg Convergence and Geometry in the projector for the source the block corresponds to The block header contains the basic characteristics of the source and the projector configuration used to display the source Block Header Block Number 01 Source Number 01 Horizontal Frequency 15 6 kHz Vertical Frequency 50 Hz Input Type video Scan Switch Configuration Front Ceiling example of block header The data representing the various adjustments for the source follows the block header Source numbers 90 99 Source numbers 90 99 do not correspond to physical inputs to the projector or RCVDS They are used to
47. djust area using arrow keys Toggle between SEL and ADJ with lt ENTER gt lt ENTER gt continue lt EXIT gt to return Use the control disk to make horizontal or vertical convergence adjustments in the selected zone and then press ENTER to move the box to another zone or EXIT to return to the Convergence menu ENTER toggles the control disk between zone selection and zone adjustment EXIT returns to convergence menu CONVERGE ADJUSTMENT WO green image 70 id fa lr red image ge rie 5975977 BARCODATA 708 260597 uz en Random Access Adjustment Mode 6 12 5975977 BARCODATA 708 260597 Service Mode SERVICE MODE Starting up the Service mode Use the control stick to highlight Service and then press ENTER ADJUSTMENT MODE Some items in the Service mode are password protected when the password function is active Enter your password to continue All other password protected items are now also available if you stay in the adjustment mode Select a path from below GUIDED RANDOM ACCESS INSTALLATION IRIS source 1 ENTER continues to the Service Mode main menu EXIT returns to the Operational mode JES SERVICE MODE The service items are combined in two service menus To switch from the first to the second menu or vi
48. dle side he hori Hr on the upper side Corrects the keystone geometry correction of the hor lines Corrects for curvature of side Corrects for curvature of S on the lower side Corrects the keystone geometry correction of the hor lines Correct by pushing the control stick forward Correct by pushing the control stick backward 5975977 BARCODATA 708 260597 Size Adjustment Push the control disk up or down to highlight SIZE on the Geometry menu and then press ENTER ENTER will select size adjustment EXIT returns to random access adjustment mode menu ADJUST returns to operational mode Adjust the horizontal size by pushing the control disk to the right orto the left until the exact image width is obtained Adjustthe vertical size by pushing the control disk up or down until the exact image height is obtained Note If the internal pattern was selected this pattern remains on the screen If the genlocked pattern was selected the external source will be displayed A bar scale and a numeric indicator help to gauge the size adjustment Hint In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity do not use an excessively small horiz
49. ect the corresponding source number between 90 and 99 The adjustment block for the source number between 0 and 9 is copied to the corresponding source number between 90 and 99 3 Enter the adjust mode and make any desired changes geometry convergence sync fast slow enhanced blue on off to the second adjustment block 4 Exit the adjust mode Note the above also applies to source number 1 5 and 91 95 of a stand alone projector no RCVDS Adjustment Blocks and Source Numbers 90 99 5975977 BARCODATA 708 260597 Insert Card INSERT CARD INPUT SOURCES INPUT SOURCES PROJECTOR soja a O n Xola as o in INPUT SOURCES INPUT SOURCES o joja mn ojoljo olalo ni o 5975977 BARCODATA 708 260597 bd
50. enu selections and also vertical and horizontal adjustments The ENTER and EXIT keys are used to move forward and backward through the menu structure The ADJUST key can be used to terminate the adjustment mode while a path selection menu head menu is displayed There are 5 possible paths to follow once in the Adjustment mode They are INSTALLATION Installation should be selected if the projector has been relocated and or a different screen size is desired When selecting Installation the user or operator will be warned to call a qualified technician to perform the installation procedure see example of projected warning on next page GUIDED Guided should be selected if the user intends to perform a complete alignment of the projected image All of the necessary geometry and conver gence adjustments are made in a predetermined sequence 5975977 BARCODATA 708 260597 Safety Instructions START UP OF THE ADJUSTMENT MODE m O ADJUST EXIT m m O pa STANDBY ENTER GENERAL ACCESS SHARPNESS TINT 5 6 COLOR 3 4 BRIGHTNESS 1 2 CONTRAST Enter ADJUST Select with 4 4 4 OF my then lt ENTER gt lt EXIT gt to return GENERAL ACCESS
51. g a BARCO LOGO LANGUAGE ENGLISH ESPA OL FRANCAIS DEUTSCH Select with or 4 then lt ENTER gt lt EXIT gt to return 7 3 Service Mode Change Projector Address Every projector requires an individual address between O and 255 This address can be software installed To change that address push the control disk up or down to highlight Change Porjector Address and press ENTER The Change Projec tor Address menu will be displayed and the actual address will be filled in ENTER displays the Change Projector Address menu PS EXIT returns to the Service mode main menu The first digit is highlighted Select the individual digits by pushing the control disk to the right or to the left Reprogram with the digit keys on the RCU Press ENTER to confirm Press EXIT to return to the projector set up menu Change baudrate The communication speed between projector and computer has 8 possible speeds The baud rate speed can be software set up Highlight Change Baudrate by pushing the control disk up or down and press ENTER to display the Baud rate menu The following baud rates are available 9600 4800 2400 1200 600 300 150 110 The actual baud rate will be highlighted To change the baud rate push the control disk up or down or to the left or to the right to select the desired baud rate and press ENTER to accept this baud rate ENTER to accept the se
52. g period both video signals are modulated by appropriate waveforms so that the resulting light output equals the rest of the image Contrast modulation kit The contrast modulation kit is designed to improve overall light output uniformity and to overcome the inherent color shift errors normally associated with CRT projection The laws of physics applied to projection optics dictate that the center of the projected image will be brighter than the corners this phenomenon is normally referred to as corner fall off Due to the normal off axis projection of the red and blue images CRT projection displays a phenomenon referred to as color shift whereby one side of the image is reddish and the other blueish By modulating the amplitude of the video signal with appropriate waveforms we are able to overcome both problems The use of this contrast modulation kit is described in appendix C Order number R9827800 5975977 BARCOGRAPHICS 708 260597 Adjustment Blocks and Source Numbers 90 99 ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90 99 Adjustment Blocks memory blocks As the projector is digitally controlled all geometry and convergence adjustments are stored in the projector s memory as numeric values These numeric values are used to control digital potentiometers which in turn control the projector Each source connected to the projector has a unique set of adjustment data which is automatically downloaded into the projector s
53. hen lt ENTER gt lt EXIT gt to return When your password is correct you get access to the Adjustment mode E E S Ki e onamo When the entered password is wrong the message Wrong password will be displayed Once the password is correctly entered all other password protected items are accessible without re entering your password When re entering the adjustment mode it will be necessary to enter your password again when selecting a password protected item 5 2 PE gt 5975977 BARCODATA 708 260597 Random Access Adjustment Mode RANDOM ACCESS ADJUSTMENT MODE Starting up the random access adjustment mode Push the control disk up or down to highlight RANDOM AC CESS and then press ENTER ADJUSTMENT MODE Some items inthe Random access mode are password protected Select a path from x y below when the password function is enabled Enter your password d A GUIDED to continue All other password protected items are now also available if you stay in the adjustment mode ER IRIS e source 1 ENTER continues to Setup Pattern Selection be Jean e ai EXIT returns to operational mode J ENE Overview random Access Adjustment mode COLOR BALANCE H SYNC H LINE DOUBLER PORT H PHASE V CENTERLINE BOW RASTER SHIFT GEOMETRY H V CENTERLINE SKEW RANDOM ACCESS L LEFT RIGHT E W mH SIDE BOW ADJUSTMENT MODE SEAGULL CORRECTIO
54. hted item N EXIT returns to the Path Selection main menu SST returns to the Operational mode B To copy the settings of a closed block to the block you are working on active block use the control disk to select a block All existing settings will be overwritten with the new settings Press ENTER to copy the selected block A confirmation screen will be displayed ENTER displays a confirmation screen N EXIT returns to the Service Mode main menu J M If you are certain you wish to copy the contents of the selected block into the active block press ENTER EXIT cancels the copy procedure and returns without copying the block Deletion of blocks This item is password protected The delete function is used to clear all data settings from an adjustment block A delete can be given block by block or forall blocks Deleting block by block The delete a block function deletes the settings of a selected block Highlight Delete a block with the control disk and press ENTER ENTER will select the pointed item SN EXIT returns to the Path Selection main menu ree returns to the Operational mode Push the control disk up or down to select the desired adjustment block Press ENTER to delete the selected adjustment block A confirmation menu will be displayed ENTER displays the confirmation menu EXIT returns to the Service Mode main menu ENTER will delete the selected bl
55. id input but the source is not connected to the input terminals or the input source is switched off When a wrong key is pressed on the ROU 5975977 RETRODATA 708 260597 WARNING invalid code entry WARNING end of ad just range WARNING input no longer available WARNING input se lector not available WARNING invalid frequency input table is deleted FAILURE 12C error addr 7FH3 FAILURE short circuit on 12C bus Messages warnings and failures MESSAGES WARNINGS AND FAILURES Message when the entered pass word is wrong End of adjustment range Message will be displayed when the input source is no longer avail able The following message then appears check input signal or se lect new source It warns you to check the power connection or the power status of the RCVDS Next message will appear immediatly on the screen go to stand by The entered frequency or applied frequency of the source is out of the projector s range Message to inform that selected table is deleted This message will be followed by confirm message on which the user has to answer Hardware failure Call a qualified service technician for repair Hardware failure Call a qualified service technician for repair 1 1 Messages warnings and failures FAILURE RCVDS com munication error FAILU
56. is correctly adjusted the H Phase text box is projected in the middle of the raster At that moment the gt lt icon indicates the middle of the raster Adjust the H Phase control until the middle of the projected image is equal with the middle of gt lt icon Note If the genlocked pattern was selected the external source will be displayed A bar scale and a number indicator between O and 100 on the screen give a visual indication of the horizontal phase adjustment ENTER continues to geometry menu 5975977 BARCODATA 708 260597 RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING ETRY CONVERGENCE COLOR SELECT GEOMETRY H PHASE RASTER S LEFT RIGHT E W TOP BOTTOM N S SIZE V LINEARITY BLANKING Select with or t then lt ENTER gt lt EXIT gt to return Push the control disk to the right to correct Push the control disk to the left to correct GEOMETRY H PHASE RASTER SHIFT LEFT RIGHT E W TOP BOTTOM N S ZE SI V LINEARITY BLANKING 6 5 Random Access Adjustment Mode Raster Shift Adjustment The green raster must be centered both horizontally and vertically on the center of the CRT surface To center the green raster look into the green lens and use the control disk to move the raster CAUTION It is necessary to look
57. is displayed on the screen use the control disk to highlight 2 press ENTER to select the highlighted source Depending on the priority setting in the Picture Tuning menu Video or S Video can be displayed If the setting is not correct start up the adjustment mode by pushing on the ADJUST key Select Random Access and press ENTER Select Selected source and press ENTER Highlight Picture Tuning and press ENTER Highlight Port 2 Video and press ENTER to toggle between VIDEO and S VIDEO Press EXIT to return Press ADJUST to return to operational mode 5975977 BARCODATA 708 260597 Connections jo 00000 m Luma Chroma VCR S VHS Oro Audio amplifier 5 3 1 Enter ADJUST Select with 4 e or then lt ENTER gt lt EXIT gt to return GENERAL ACCESS SHARPNESS 6 4 BRIGHTNESS CONTRAST TINT COLOR gt ADJUSTMENT MODE Select a path from below GUIDED RANDOM ACCESS INSTALLATION Choose a setup pattern from below SELECTED SOURCE GENLOCKED PATTERN
58. king between OFF and ON During the creation of new settings for a RGB source the peaking is switched to OFF Color Select Highlight COLOR SELECT by pushing the control disk up or down and press ENTER to display the color select menu ENTER continues to the color select menu EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu ADJUST returns to operational mode Use the control disk to highlight a color CRT or combination of colors to display the projected image in that specific color To select a new color press ENTER the color selection menu appears again on the screen To terminate the color select proce dure press EXIT ENTER continues with the selected color or color combina tion EXIT returns to the Random access main menu 6 4 PICTURE TUNING COLOR BALANCE SYNC FAST PEAKING ON Select with 4 or t lt ENTER gt to accept lt EXIT gt to return LEDS PICTURE TUNING COLOR BALANCE SYNC FAST PEAKING ON LINE DOUBLER ON PORT 2 S VIDEO Select with 4 or t lt ENTER gt to accept lt EXIT gt to return PICTURE TUNING COLOR BALANCE SYNC FAST PEAKING LINE DOUBLER N Select with Y or f lt ENTER gt to accept lt EXIT gt to return LED RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE COLOR SELECT zr COLOR SELECT RED
59. lected baud rate D EXIT to return without changing the baud rate PA Power up mode When pressing the power switch the projector can start up in operating mode or in stand by mode Operating mode the projector start up and displays image Stand by mode the projector start up in stand by and waits until the stand by button or a digit key is pressed To change the Power up mode select Power Up mode by pushing the control disk up or down and press ENTER to toggle between Operating and Standby ENTER to toggle between operating and standby EXIT to return to the Service menu 7 4 PROJECTOR SET UP CHANGE PASSWORD CHANGE LANGUAGE CHANGE BAUDRATE POWER UP MODE operating m J BARCO LOGO A IDENTIFICATION TOTAL RUN TIME PROJECTOR ADDRESS Enter new projector address 000 Used and mp to select and reprogram with numeric keys Highest address is 255 LEX lt ENTER gt to confirm lt EXIT gt to return PROJECTOR SET UP CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS d POWER UP MODE operating IDENTIFICATION TOTAL RUN TIME BARCO LOGO E BAUDRATE Select new baudrate 9600 4800 2400 1200 600 300 150 110 X Select with arrow keys lt ENTER gt to accept lt EXIT gt to return Kaes PROJECTOR SET UP IDENTIFICATION TOTAL RUN
60. ments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information or noise A 0 on the bar scale indicates no blanking To start up the Blanking adjustments follow the next procedure Push the control disk up or down to highlight BLANKING on the Geometry menu and then press ENTER The following blanking corrections are possible Top blanking Bottom blanking Left blanking Right blanking Therefore If the internal pattern was selected this pattern remains on the screen If the genlocked pattern was selected the external source will be displayed Adjust the next blanking alignments until the image is correctly framed or the unwanted information is blanked out To enter a blanking alignment push the control disk up or down to highlight a function and press ENTER to activate this function Press EXIT to return BLANKING TOP BOTTOM LEFT RIGHT Select with 4 or 4 then lt ENTER gt lt EXIT gt to return 6 10 GEOMETRY H PHASE RASTER SHIFT LEFT RIGHT E W TOP BOTTOM N S SIZE Left blanking fe nan V LINEARITY IBLANKING BLANKING Select with Y ot then lt ENTER gt lt EXIT gt to return NIJ A blanking Right blanking Bottom blanking Adjustment of the blanki
61. n link for PC or MAC to the next projector IR sensor receiver for control signals transmitted from the RCU Communication port 800 peripherals allows communication between the RCVDS switcher and the projector allows connection of a remote IR receiver unit to the projector allows connection of an IRIS 800 to converge the image automatically IR Remote remote input for wired remote control Front Panel Terminology RGB S IN or R Y Y B Y S IN 4x BNC connector RGB S in allows a character generator microcomputer video camera etc having analog RGB output to be con nected to the projector Line inputs signals RED GREEN BLUE COMPOSITE sync signal R Y Y B Y S IN component in allows to connect e g a professional VCR having component outputs to the projec tor Line inputs signals RED LUMA LUMA BLUE LUMA COMPOSITE sync signal VIDEO IN Composite video 1x BNC connector allows a video tape recorder video camera color receiver monitor etc having video line output to be connected to the projector S VIDEO IN Separated Y C luma chroma signal inputs and outputs for higher quality playback of Super VHS signals 4 pin S VIDEO connector AUTODIAGNOSIS DISPLAY LED indication for service purposes o0000000000000 EZE ZS Let N o lt a gt 2 8 lt JNIOJ ANO GH NMOA 10H ANOO GH LH o lt AGGNVLS 1H3 NMOd 10H POWER MAINS S
62. ng on the of the image y t Correct by pushing the control disk up or down 8 Adjustment of the blanking on the eft side e Correct by pushing the control disk to the right or to the left 5975977 BARCODATA 708 260597 Random Access Adjustment Mode Convergence Adjustment Convergence adjustments affect both the horizontal and vertical lines of the setup pattern These adjustments are performed on the red image while superimposed on the green image and then on the A JUSTMENT MODE blue image while superimposed on the green image PICTURE TUNING Note the green convergence adjustments can be added as an t option When these are available start always with green only This COLOR SELECT option will also be indicated on the convergence menu Highlight first Green only when available by pushing the control disk up or down and press ENTER to display the convergence adjustment menu CONVERGENCE GREEN ONLY RED ON GREEN BLUE ON GREEN Select with Y or f then lt ENTER gt lt EXIT gt to return The screen area is divided into 25 areas Use the control disk to move the box to the desired zone and then press ENTER to begin the convergence adjustment Start the i A CONVERGENCE convergence adjustment with zone one and continue as mentioned ee in the diagram hereafter using arrow keys ADJ a
63. ock EXIT cancels the deletion procedure and returns to the Service mode main menu 7 6 MEMORY MANAGEMENT DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R amp B CONVERGENCE MID GR CONVERGENCE MID COPY MODE Nr Src Fh Fv inp conf 1 1 15 6 50 video FC 2 3 31 2 60 RGB3S RT 3 15 6 50 intern FC 4 2 31 5 50 RGB3S FC 5 33 7 60 intern FC 6 T7 8 Active block nr 1 CC COPY BLOCK All settings m in current block will be overwritten lt ENTER gt to confirm lt EXIT gt to cancel SS 2 SR MEMORY MANAGEMENT COPY A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R 8 B CONVERGENCE MID GR CONVERGENCE MID LEDS 33 7 60 DELETE MODE Nr Src Fh Fv inp conf 1 1 15 6 50 video FC 2 3 31 2 60 RGB3S RT 3 15 6 50 intern FC 4 2 31 5 50 RGB3S FC 5 intern 6 7 8 Active block nr 1 FC DELETE BLOCK m The selected block will be deleted lt ENTER gt to confirm lt EXIT gt to cancel 5975977 BARCODATA 708 280597 Deletion of all blocks Highlight delete all blocks with the control disk and press ENTER ENTER gives a confirmation message before deleting N EXIT returns to the Path Selection main menu J pl If you are certain you wish to delete all blocks press ENTER to confirm otherwise press EXIT to return Once ENTER is pressed all
64. of the cover at the same time fig 1 Insert the new 9 V battery E block type e g 6F22S or equivalent in the lower compartment and connect the battery to the contact plate Insert the battery into the lower compartment and put the cover back r T Insert here behind the plastic cover the Insert card for RCU You can Contact cut out this card plate on one of the last pages of this manual fig 1 Battery fig 2 i 310a DRW 5975977 BARCODATA 708 260597 mmm 4 1 Controlling The projector can be controlled with a The RCU b The hardwired RCU cable not included c The local keypad Controlling the projector with the RCU and the hardwired RCU is the same How to use the RCU a Point the front of the RCU towards the reflective screen surface Ceiling We eee IR sensor Screen Be b Point the front of the RCU towards one of the IR sensors in the projector When using the wireless remote control make sure you are within the effective operating distance 30m 100ft in a straight line The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector s IR sensor Front of projector Rear side of projector D l oog Lonen _ xia
65. ojector In addition the audio signal proper to the source can be switched to an audio amplifier Order Numbers 110V 9827890 220V 9827899 IRIS 2 Auto Convergence System Easy to use high precision automatic convergence system Convergence time less than 2 30 Various options on the menu offer you the optimal solution for your own individual needs Align Convergence starts from the current image situation Align from midposition Convergence starts from midposition Touch up Convergence starts when the source switches or after a user defined time alignment of static convergence almost invisible for the audience 9 1 Options MAGIK Interface Multifuctional Analog Graphics Interface Kit BARCO s MAGIK interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the connection with its own display The MAGIK interface buffers and amplifies any RGB analog signal with TTL or analog sync without signal loss or image degradation The MAGIK can be delivered together with connection cables for PC MAC SUN or workstation in a nice handbag case Order numbers MAGIK with cables and case R9828120 230V R9828129 120V Order number MAGIK only R9828121 230V R9828128 120V Adapter and communication cables BARCO provides several cables to connect peripheral equipment to the projector
66. ontal size setting EXIT will return to Geometry 4 t Ideal Ideal Image Image too Image Image too Hight Tall Hight Short 4 t Vertical Linearity Adjustment The vertical linearity adjustment function corrects for vertical non linearities which extend from the center of the image to the top and bottom of the image Push the control disk up or down to highlight V LINEARITY on the Geometry menu and then press ENTER ENTER will select vertical linearity adjustment EXIT returns to random access adjustment mode menu ADJUST returns to operational mode Adjust the vertical linearity with the control disk until the distances between the horizontal lines of the set up pattern are equal from top to bottom EXIT will return to the Geometry menu 5975977 BARCODATA 708 260597 Random Access Adjustment Mode GEOMETRY H PHASE RASTER SHIFT LEFT RIGHT E W TOP BOTTOM N S VL Ye BLANKING H size too large gt H size too small Ideal image width GEOMETRY H PHASE RASTER SHIFT LEFT RIGHT E W TOP BOTTOM N S H SIZE V SIZE BLANKING V LINEARITY 70 Random Access Adjustment Mode Blanking Adjustments Blanking adjust
67. placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register The projector should not be placed in a built in installation or enclo sure unless proper ventilation is provided 4 Do not block the projector cooling fans or free air movement under and around the projector Loose papers or other objects may not be nearer to the projector than 4 on any side On servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock Refer all servicing to qualified service personnel 1 2 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the equipment c lf the product has been exposed to rain or water d If the product does not operate normally when the operating instructions are followed Note Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation e Ifthe product has been dropped or the cabinet has been damaged f If the product exhibits a distinct change in performance indicating a need fo
68. r saturation is only active for Video and S Video Adjustthe color intensity of the picture Adjust the color saturation using the and buttons RCU or pushing the control disk to the left or to the right local keypad A bar scale gives a visual indication on the screen of the current color setting while pressing on the above indicated buttons If the bar scale is not visible on the screen press TEXT key once and retry the above indicated buttons The bar scale increases when pressing on the button richer colors and decreases when pressing the button lighter colors Tint Control Tint is only active for Video and S Video Tint control is effective only when using the NTSC 4 43 or NTSC 3 58 system A bar scale gives a visual indication on the screen of the current tint setting while pressing the or buttons RCU or pushing the control disk to the left or to the right local keypad If the bar scale is not visible on the screen press the TEXT key once and retry the above indicated buttons The bar scale increases when pressing on the button and de creases when pressing the button Sharpness Control Sharpness control only active for Video and S Video A bar scale gives a visual indication on the screen of the current sharpness setting while pressing the or buttons RCU or pushing the control disk to the left or to the right local keypad If the bar scale is not visible on the screen press TEXT key once and
69. r service Replacement parts When replacement parts are required be sure the service technician has used original BARCO replacement parts or authorized replacement parts which have the same characteristics as the BARCO original part Unauthorized substitutions may result in degraded performance and reliability fire electric shock or other hazards Unauthorized substitutions may void warranty Safety check Upon completion of any service or repairs to this projector ask the service technician to perform safety checks to determine that the product is in proper operating condition On cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning To keep the cabinet looking brand new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution Never use strong solvents such as thinner or benzine or abrasive cleaners since these will damage the cabinet To ensure the highest optical performance and resolution the projection lenses are specially treated with an anti reflective coat ing therefore avoid touching the lens To remove dust on the lens use a soft dry cloth Do not use a damp cloth detergent solution or thinner On repacking Save the original shipping carton and packing material they will come in handy if you ever have to ship your equipment For maximum p
70. retry the above indicated buttons The bar scale increases when pressing on the button sharper picture and decreases when pressing on the button softer picture The Pause key When the Pause key is pressed the image projection is stopped but the projector remains with full power for immediate restart To restart the image Press the Pause key Select a source number 5975977 BARCODATA 708 260597 Adjustment mode All picture geometry and convergence adjustments are made while in the Adjustment mode Two possible ways to enter the adjustment mode a Using the RCU Press the ADJUST key The projector displays the path selection menu b Using the local keypad Press the ADJUST key The projector displays the General access menu Use the control disk to highlight enter ADJUST and press ENTER The path selection menu will be displayed Note to adjust the Analog picture control while in the Adjustment mode press the ADJUST key The next General Access menu will be displayed Push the control disk up or down to select the analog control to be adjusted and press the ENTER key to confirm When the analog control is adjusted the projector returns automatically to the General access menu When you want to return to the Adjustment mode press EXIT otherwise select quit ADJUST and press ENTER to return to operational mode You are now in the Adjustment mode The control disk is used to make m
71. rotection repack your set as it was originally packed at the factory On illumination In order to obtain the best quality for the projected image itis essential that the ambient light which is allowed to fall on the screen be kept to an absolute minimum When installing the projector and screen care must be taken to avoid exposure to ambient light directly on the screen Avoid adverse illumination on the screen from direct sunlight or fluorescent lighting fixtures The use of controlled ambient lighting such as incandescent spot light or a dimmer is recommended for proper room illumination Where possible care should also be taken to ensure that the floors and walls of the room in which the projector is to be installed are non reflecting dark surfaces Brighter surfaces will tend to reflect and diffuse the ambient light and hence reduce the contrast of the projected image on the screen 5975977 BARCODATA 708 260597 Rear Panel Terminology Cee Location and Function of Controls LOCATION AND FUNCTION OF CONTROLS ee o EE 5 Eo 0 OOOOO o o SH AUD A DODO OG DO RS232IN Connection between the projector and an IBM PC or compatible or MAC RS422 for remote computer control and data communication RS2320UT Used to connect to the next projector RS232IN plug communicatio
72. ss digit button 1 1 Comp Video S Video Comp Video RGBS or RGsB wee s Input signal Y C luma chroma RGB3S or RG3sB s Input signal R G and B with composite sync on G or separate composite sync R Y Y B Y S or Reg Input signal R G and B with Tri level sync on G or separate Tri level sync We Input signal R Y Y and B Y with composite sync on Y or separate composite sync R Y Ys B Y R Y Y B Y 3S or Input signal R Y Y and B Y with Tri level sync on Y or R Y Y3s B Y separate Tri level sync 1 Video or S Video switchable in the Picture Tuning menu Connecting a Composite Video source Composite video signals from a VCR OFF air signal decoder etc If a line doubler is built in the default position of this line doubler is ON active the video input signal will be displayed as a non interlaced image improved image stability To enable or to disable this line doubler function enter the adjustment mode and change the position of the ON OFF toggle switch see Picture tuning in chapter Guided adjust ment mode or Random access adjustment mode Composite Video input selection a with the RCU press digit button 1 or Oo
73. st west Adjustments Left right and center adjustments affect only the vertical lines of the projected image GEOMETRY H PHASE RASTER SHIFT TOP BOTTOM N S SIZE V LINEARITY ha BLANKING M LED To start up the left right and center adjustments follow the next procedure LEFT RIGHT E W Push the control disk up or down to highlight LEFT RIGHT E W on the geometry menu and then press ENTER VGENTERLINE SKEW RIGHT BOW RIGHT KEYSTONE LEFT BOW LEFT KEYSTONE ENTER will select Left Right adjustment menu EXIT returns to random access adjustment mode main menu Select with Y or f then lt ENTER gt lt EXIT gt to return ADJUST returns to operational mode Only the green image is displayed while making left right adjust ments The red and blue images will automatically be corrected in the same manner Convergence corrections are automatically disabled for the duration of these adjustments The following adjustments can be executed vertical centerline bow vertical centerline skew side keystone left right side bow left right Corrects for curvature of the vertical lines in the middle of the image All adjustment are indicated on the screen with the function name a bar scale and a number between 0 and 100
74. t the CRT run in option ENTER starts the CRT run in when an internal generated pattern is available EXIT returns to the Path Selection main menu Projector warm up Highlight Projector warm up by pushing the control disk up or down and press ENTER to select the projector warm up menu The ON OFF option can be toggled with the ENTER key When in the ON position and the CRT run in cycle is OFF the projector can start up with a warm up periode of 20 minutes During the start up a warm up menu will be displayed This menu offers the possibility to skip the warm up periode anyway by pressing the EXIT key and offers the possibility to adjust the horizontal and vertical amplitude of this white image with the control disk During this warm up period a full white image is shifted on the CRT faceplate to avoid a burn in Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go When EXIT is pressed during this warm up periode the warm up menu will be redisplayed with the remaining time indication Press another time EXIT to interrupt the warm up cycle When the warm up option is OFF when switching on the projector it starts immediately with the projection of the selected source CRT Drive Mode The projector CRT s can be driven with the normal current normal mode a lower current economic mode or with a higher current boost mode To change the drive mode highlight CRT dri
75. t the cord pull it out by the plug Never pull the cord itself 4 If an extension cord is used with this product make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes 5 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock Never spill liquid of any kind on the product Should any liquid or solid object fall into the cabinet unplug the set and have it checked by qualified service personnel before resuming operations 6 Lightning For added protection for this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet This will prevent damage to the projector due to lightning and AC power line surges On installation 1 Do not place this equipment on an unstable cart stand or table The product may fall causing serious damage to it 2 Do not use this equipment near water 3 Slots and openings in the cabinet and the back or bottom are provided for ventilation to ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by
76. ted item R EXIT returns to the Service mode menu E SS The Identification screen gives information concerning Projector address To change the address of your projector contact a qualified service technician Software version Configuration Possible installations Front ceiling Front table Rear ceiling Rear table Baud rate PC transfer speed for communication with an IBM PC or compatible or MAC The baud rate of the projector must be the same as the baud rate of the connected computer When there is a difference contact a qualified service technician to make the appropriate changes Text ON OFF Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed ON displayed OFF not displayed The status can be changed by pressing the TEXT key once on the RCU Serial no indicates the fabrication number of the projector This number can be useful when calling for technical assistance 7 2 N SERVICE MODE MEMORY MANAGEMENT COMMON SETTINGS 12C DIAGNOSTICS CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS POWER UP MODE operatin B j BARCO LOGO i Y PROJECTOR SET UP IDENTIFICATION TOTAL RUN TIME CHANGE PASSWORD CHANGE BAUDRATE Select with Y or f then lt ENTER gt lt EXIT gt to return BARCO LO PROJECTOR SET UP IDENTIFIC
77. ted sources variable adjustment speed when pushing continuously on the arrow keys or the picture keys the adjustment will be executed in an accelerated fashion Ge e Ju 2 10 Local keypad RCU a R e Wier 11 STANDBY ENTER 1 BARGO 1 40 EE 4 11 9 8 9 0 suites stand by D Si Deg 7 le FI le i OQ i E ause par 5 KR i 3 a BRIGHTNESS J sharpness D l 1 2 SE tint heed color B brightness T contrast O 5975977 BARCODATA 708 260597 2 2 EMO El Ps ee Back light key when activated all keys will be lit up and visible in the dark ADJ adjust key to enter or exit the adjustment mode Address key recessed key to enter the address of the projector between O and 9 Press the address key followed by pressing one digit button between 0 and 9 STBY stand by button to initiate remote power up operation to stop projection without main power off Pause to blank the image press PAUSE The image disappears but full power is retained for immediate restart ing Digit buttons direct input selection Picture controls use these buttons to obtain the desired level see also Controlling for each picture function 5975977 BARCODAT
78. tie Project ira 3 6 Connecting a RCVDS 05 switcher to the projector oooocccnnniccnnnnncccccnnonnnncononnnnnnar cnn nnnnc ca nnnnn cc 3 6 Connecting a VSO5 switcher to the projector 00aaaa aaa aaa 3 6 Connecting an IR Remote Receiver to the projector aaa aaa kakaa 3 6 Peripheralegquipmient 52 eee i ao aa ddadda a KEKE 3 6 CON TROLIN sra AAA A A AE 4 1 Battery installation in the ROU 000 aaa 4 1 Howto USES RC ees e Eege 4 2 lee 4 2 How to display a projector address 4 2 How to program an address into the RCU 000 aaa aaa 4 3 alle le EE 4 3 Picture elt EEN 4 4 The PAUSE kV ia ani 4 4 5975977 BARCODATA 708 260597 LI Table of Contents START UP OF THE ADJUSTMENT MODE oil iio aid is 5 1 Adjustment MOda ai iiir ae A E AOAR E AANE A AE A E A 5 1 Starting up the random access adjustment mode 6 1 RANDOM ACCESS ADJUSTMENT MODE aaa kaaa 6 1 Overview random Access Adjustment mode 6 1 Selecting Setup Pattern ivi a aa alah 6 2 Internal Cross Hatch Pattern 00 aaa 6 2 Random access adjustment mode selection menu 000 kaaa 6 3 Picture TUTI eiaa da 6 3 Color Balance ii ee IC 6 3 Sync Fast Slow Adjustments sinian ka 6 3 Line Doubler Option wcities et Pe dee Sea nee ee dee 6 4 Port2 S VideoNideo idad ds do RN heefeg eer 6 4 IST Le BEE 6 4 Color Select cnc ais 6 4 Geometry AdjUStMeNt inini nadia naa ad aaa aa aaa a aK Eaa iiaae 6 5 Horizontal Phase Adjustment anea aaa anna 6
79. tion manual Order number R9827780 Line Doubler Kit BARCO s line doubler kit consists of a video decoder with a three line adaptive Comb filter an enhancement circuit and the line doubler itself The three line adaptive Comb filter improves color transitions and reduces noise in the video signal The enhancement circuit integrated in the decoder provides sharper images with clearer outlines The line doubler circuit reduces visible line structure by doubling the number of lines of the video image These three circuits work in unison to produce a smoother yet sharper image which is significantly more appealing when watching video images Order number R9828161 Ceiling mount CM50 This suspension system enables to mount any projector from the BARCO 700 series to the ceiling without using any mechanical interface and to adapt the projector perfectly to the local mounting requirements Order number CM50 with pulley R9827990 Order number CM50 without pulley R9827991 Soft edge matching kit Multi screens are popular for many applications In these installa tions the goal is to obtain a contiguous matched image forming one homogenous view The soft edge matching feature provides a solution to the annoying side effects when adjusting two or more projected images next to each other To improve this junction both images must be overlapping within a certain percentage of the total screen width During the overlappin
80. to the previous settings Green convergence mid Only available when the projector is equipped with green conver gence adjustmentes Highlight Gr convergence mid by pushing the control disk up or down and press ENTER to switch off the green convergence Undo green convergence mid Only available when the projector is equipped with green conver gence adjustmentes The item Undo green convergence mid will automatically be dis played when the green convergence is switched to midposition Press ENTER to switch on the green convergence 7 8 MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS GR CONVERGENCE MID R amp B CONVERGENCE MID m Convergence settings in current block Will be overwritten lt ENTER gt to confirm lt EXIT gt to cancel MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS GR CONVERGENCE MID Select with 4 or t then lt ENTER gt lt EXIT gt to return MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS am ALL SETTINGS TO MIDPOS R amp B CONVERGENCE MID ptf GR CONVERGENCE MID Select with 4 or t then lt ENTER gt lt EXIT gt to return MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R amp B CONVERGENCE MID H
81. urce connected to one of the inputs and the Genlocked Pattern is selected Internal Cross Hatch Pattern The Internal pattern menu will be displayed if the internal cross hatch pattern has been selected or if no source is connected to the projector The table below lists the 8 fixed factory preset frequencies available Another 8 blocks are custom programmable Push the control disk up or down to highlight the desired cross hatch frequency Push the control disk tp the left or to the right to scroll to another page Press ENTER if the desired block is selected kHz Hz 15 6 50 PAL SECAM 15 7 60 NTSC 31 2 50 EDTV 31 5 60 IDTV 31 2 50 HDTV EUREKA 31 5 60 HDTV ATV 33 7 60 HDTV HIVISION 15 8 60 EGA 1 21 8 60 EGA 2 31 5 60 VGA 3 31 5 70 XGA 1 2 35 5 87 VGA 4 44 2 70 SUPER VGA 2 48 5 60 SUPER VGA 1 61 0 76 SUPER VGA 3 63 9 76 APOLLO ENTER continues to the Random Access Adjustment Mode EXIT returns to the Setup Pattern Selection menu 6 2 Choose a setup pattern from below SELECTED SOURCE GENLOCKED PATTERN INTERNAL PATTERN Source 01 A Gel LED Select with 4 or t then lt ENTER gt lt EXIT gt to return INTERNAL PATTERN kHz Hz 15 6 50 PAL SECAM 15 7 60 NTSC 31 2 50 EDTV AA 31 5 60 IDTV RJ 31 2 50 HDTV EUREKA i f 31 5 60 HDTV ATV Select with J or f 7 scroll with gt or lt lt ENTER gt to accept lt EXIT gt to return 5975977 B
82. ve mode by pushing the control stick forward or backward and press ENTER to display the CRT drive mode menu To change the boost mode push the control disk up or down to select a display mode and press ENTER to select The following modes are available Normal Economic Lower drive current to the CRT s the lifetime of the CRT s will enlarge but the light output will reduce Tempory boost Higher drive current to the CRT s the lifetime of the CRT s will shorten but the light output will be higher This situation is tempory when restarting the projector the drive mode is auto matically set to normal Permanent boost Higher drive current to the CRT s the lifetime of the CRT s will shorten but the light output will be higher This setting will be saved in the EEPROM When restarting the projector it will start up in boost mode 7 10 CRT RUN IN CYCLE A flashing white pattern will be generated until lt EXIT gt is pressed The projector only uses memory blocks adjusted on an intemal pattem if no such block is available the projector can t run the procedure and leaves the adjustment mode ADS lt ENTER gt to continue lt EXIT gt to cancel COMMON SETTINGS G2 ADJUSTMENT CRT RUN IN CYCLE PROJECTOR WARM UP CRT DRIVE MDOE Var Select with 4 or t then lt ENTER gt lt EXIT gt to return PROJECTOR WARM UP OPTION ON A FULL WHITE PATTERN WILL BE GE
83. w to display a projector address Press the ADDRESS key recessed key on the RCU with a pencil The projector s address will be displayed in a Textbox This text box disappears after a few seconds a PIAR PROJECTOR ADDRESS 001 5975977 BARCODATA 708 260597 To continue using the RCU it is necessary to enter an address with the digit buttons address between O and 9 For example if the Address key displays projector address 003 the press 3 digit button on the RCU to set the RCU s address to match the projector s address Do not press digit 003 This will address the remote to 0 and control all projectors in the room How to program an address into the RCU Press the ADDRESS key recessed key on the RCU with a pencil and enter the address with the digit buttons That address can be any digit between 0 and 9 Input selection Source No Projector input Press button 1 1 Comp Video S Video Comp Video RGBS or RGsB RGB3S or RG3sB R Y Y B Y S or R Y Ys B Y R Y Y B Y 3S or R Y Y3s B Y Two possible ways of selecting an input a With the digit buttons on the RCU it is possible to select one of the four input sources Video S Video RGsB or RGBS RG3sB or RGB3S R Y Ys B Y or R Y Y B Y S R Y Y3s B Y or R Y Y B Y 3S b With the local keypad press first the ADJUST key to display the General access menu m oO STANDBY o EXIT E m GI ENTE

Data 708

Contents

Download Pdf Manuals

Related Search

Related Contents