User Manual
Contents
1. optional AE i AO ms PoE Fig 1 1 Plug the Ethernet cable into the RJ45 connector labelled Port 1PoE as shown in Fig 1 The second RJ45 connector labelled Port 2 is for daisy chaining further Ethernet devices without the need for another Ethernet cable If no PoE available Connect a snom approved 5 V 10 W power adapter to the power connector labelled 5V DC 2 Connect the loudspeaker wires to the speaker terminals labelled Speaker as shown in Fig 2 Connect the wire with the red terminal connect the wire with the black terminal Note If you want to use a headset during the setup e Connect the headset s microphone plug to the jack labelled Mic In Connect the headset s speaker plug to the jack labelled Line Out snom PA1 User Manual Initializing and Configuring the PA1 lnitializing and Configuring the PA During setup Status of PA1 Connect the device I Sending DHCP request Network with DHCP Network without DHCP Press the IP Reset button Application starts with the settings received from the server IP address netmask etc Application starts with the default IP adress and netmask Web interface available Press the IP Reset button to listen to the announce ment of the IP address Web interface available Default IP adress 192 168 0 2 it can also be listened to by pressing the IP Reset bu2. c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus itis not the intent of this section to claim rights or contest your rights to workwritten entirely by you rather the intentis to exercise the rightto control the distribution of derivative or collective works based on the
3. Click on snom DAT Update Guide Category Firmware Redirected from Firmware This Firmware Wizard will guide you through the Firmware Update Downgrade Process Please click on the VoiP Phone image to proceed or select the Emergency Update Downgrade via TFTP Der Firmware Assistent wird Sie durch den Firmwareupdate bzw downgrade Vorgang f hren Bitte klicken Sie auf das Symbol Ihres VoIP Telefons oder wahlen Sie das Notfall Update Downgrade via TFTP aus preses EI snom300 Update snom320Update snom360 Update snom720 snom760 Update o 1 Guide Guide Guide 5nom370 Update Guide snom710 Update Guide Update Guide Guide m 2 K amp I S 4 snom UC edition Ax dei A snom820 Update snom821 Update snom870 Update snom MeetingPoint Update snom ONE mini Re Guide Guide Guide QOEM Honest FO Guide Update Guide Update Guide d The snom PA1 Firmware page opens Click on Firmware version 8 Snom PA1 Firmware lt Snom PAI Please click on the firmware version currently installed on your snom PA1 VoIP phone Bitte klicken Sie auf die Firmware Version die gegenw rtig auf Ihrem snom PA1 VoIP Telefon installiert ist V8 Firmware Version 8 21 snom PA1 User Manual Software Update e The snom DAT Firmware V8 page opens Click on Manual Update to Version Snom PA1 Firmware V8 lt Snom PA Firmware Your currently installed Firmware Version 8 X V V8 7 V8 LN ei E Manual Update for default
4. Certificates Software Update Additionally you should protect the web interface with hidden security tags against remote attackers Status trying to change phone settings with faked HTTP POST requests System Information 4 A Y Use hidden tags on Doff Log SIP Trace DNS Cache SES Press to save the settings as shown above Subscriptions PCAP cn Press to ignore the warning until reboot Memory Settings Press to ignore the warning forever Manual Firmware versions below 8 7 4 We urge you to set administrator and HTTP passwords to protect the PA1 from remote attacks The default administrator password is 0000 4 zeros there is no default HTTP password Note f you do not replace the default administrator password by an individual one an unauthorized third party could set an administrator password unknown to you In such a case you would no longer be able to switch from user mode to administrator mode Unauthorized third parties would also be able to set the device back to factory values 13 snom PA1 User Manual Initializing and Configuring the PA1 If you do not set an HTTP password you make it easier for third parties to break into your System If you set your own passwords be sure to write them down and store them in a secure place Without the administrator password you will not be able to switch the web interface from user mode to administrator mode the settings will be inaccessible Without HTTP pas
5. If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are out
6. blink Note It may take a few minutes before the PA1 aborts the DHCP request and starts the application with the default settings 3 When the application is starting up with the default network settings the red LED stops to blink and glows red steadily 4 When the PA1 boot up process is finished and the web interface is available the green LED lights up in addition to the red one You can now change the default settings manually Note Briefly press the button labelled IP Reset to listen to the oral announcement of the default IP address in English over the loudspeaker or headset 5 Open a browser on a computer connected to the same network as the PA1 and type the default IP address in the address bar http 192 168 0 2 The PA1 web interface will be loaded into the browser 11 snom PA1 User Manual Initializing and Configuring the PA1 6 Click on Advanced in the menu on the left side of the window The Advanced page opens to the Network tab D a Advanced Settings a XR Operation Home Network Behavior Audio SIP RTP QoS Security Update Directory Network Setup DHCP Bon Ooff Preferences Options on DHCP on 13461215 42 43 51 66 67 1 Spaad Dia Options on DHCP off 43 120 125 Funcson Keya IP address 10 110 25 153 tients Netmask 255 255 255 0 ied Host Name ni FER IP Gateway 10 110 25 254 Actio
7. copyrights and other legal rights worldwide Their use reproduction and transmittal to third parties without express written permission may result in legal proceedings in the criminal courts as well as civil courts When this document is made available on snom s web page snom technology AG gives its permission to download and print copies of its content for the intended purpose of using it as a manual No parts of this document may be altered modified or used for commercial purposes without the express written consent of snom technology AG Although due care has been taken in the compilation and presentation of the information in this document the data upon which it is based may have changed in the meantime snom therefore disclaims all warranties and liability for the accurateness completeness and currentness of the information published except in the case of intention or gross negligence on the part of snom or where liability arises due to binding legal provisions Our firmware includes some source code that may be used and modified by anyone and everyone under the GNU Public License GPL enclosed in the appendix provided they in turn make it available to everyone else with the same licensing agreement Please go to http www snom com en support download gpl open source for the original GPL license and the source code of components licensed under GPL and used in snom products snom PA1 User Manual Safety Disposal Cleaning of Prod
8. on green LED off will damage the firmware and render the PA1 inoperational Do NOT remove the device s power supply Ethernet cable when using PoE power adapter when not using PoE while a firmware update is ongoing Firmware update initiated On On Red LED comes on automatically or manually DO NOT TURN OFF POWER Firmware update in progress On Off Green LED turns off Blinking Off Do not turn off the power until On D I the green LED comes back on otf Off On Off Elinking Off On Off FW update completed ready Off On Red LED turns on green LED comes on snom PA1 User Manual T roubleshooting Reboot 1 Open the PA1 s web interface Troubleshooting 2 Click on Advanced in the menu on the left side of the window page The Advanced Settings page opens Click on the Update tab Click on Reboot and confirm with Yes The red LED lights up and the green LED goes out When the PA1 has finished rebooting the red LED goes out the green LED lights up and the web interface is available again Hard reboot Disconnect the power wait for a few seconds and reconnect Warning Never disconnect the power during a firmware update Cutting off the device s power during a firmware update red LED on green LED off will damage the firmware and render the PA1 inoperational In such a case the PA1 will need to be
9. phone number 2 Password Password for your account if necessary e Registrar Registrar address of your PBX software 2 Click on Apply or Re Register The Save button appears at the top of the page Operation Home A Some settings are not yet stored permanently Save View Changes Directory Setup Login SIP NAT RTP Preferences Login Information Speed Dial Identity active Bon Ooff 3 Click on Save to save the changes permanently Changes that have not been saved will be lost if and when the phone loses power or is disconnected from its power source If the registration has been successful the red Power LED will turn off The green Call LED will stay on indicating that the snom PA1 is ready to receive announcements 15 snom PA1 User Manual Initializing and Configuring the PA1 Settings Normally it is only necessary to set the time zone and the tone scheme You can adjust the default settings for loudspeaker volume amplifier gain and automatically ending calls as necessary or desired Time Zone 1 Open the PA1 s web interface 2 Click on Advanced in the menu on the left side of the window page The Advanced Settings page opens to the Network tab SS Advanced Settings SS Operation Home Network Behavior Audio SIP RTP QoS Security Update Directory Network Setup DHCP Bon Corr Preferences Options on DHCP on 1346 12 15 42 43 51 66 67 1 D Speed Dial Options on DHCP off 4
10. returned to the vendor for resetting special kit required Do NOT remove the device s power supply Ethernet cable when using PoE power adapter when not using PoE when the red light is on or blinking a firmware update is ongoing LED indications Ready or busy Off On Blinking During firmware update Firmware update initiated COn on Red LED comes on automatically or manually DO NOT TURN OFF POWER Firmware update in progress On Off Green LED turns off Blinking Off Do not turn off the power until On Oo the green LED comes back on Off Off On Off Blinking J C Off y On Off FW update completed ready Se K Sz Red LED turns off green LED comes on 23 snom PA1 User Manual Troubleshooting Reset to factory values Press the IP Reset button to the left of the LEDs Warning All customized settings will be lost See Initializing and Configuring the PA on page 10 for information on how to initialize and configure the PA1 anew Contacting snom Support Please visit our knowledge base and our forum first You may find the answer to your question in one of the topics there If you haven t found an answer or a solution to your problem please post your question or problem on the forum http forum snom com Note The forum is accessible to the general public Do not post any private and or securi
11. 3 120 125 Pm Keys IP address 10 110 25 153 e 1 Netmask 255 255 255 0 Identity 2 Host Name Identity 3 ip IP Gateway 25 2 ina way 10 110 25 254 Action URL Settings DNS Advanced Domain snom com Erna DNS Server 1 10 110 1 201 are Update DNS Server 2 10 110 1 202 e Status System Information m Time Log NTP Time Server 10 110 1 201 IP Ti 3 P Sa NTP Refresh Time sec 3600 che F 1 Germany Berlin Bd Subscriptions Timezone EN 3 In the Time section select your time zone De country city from the drop down menu of Timezone 4 Click on Apply at the bottom of the page After clicking on Apply the Save button will appear at the top of the page Click on Save to save the changes permanently in case of power loss Operation Home Directory A Some settings are not yet stored permanently Save View Changes Gi Setting Tone Scheme 1 Open the PA1 s web interface 2 Click on Preferences in the menu on the left side of the window page The Preferences page opens P ad Preferences m Operation Home General Information sn Webinterface Language English v Q Saup Language English v Preferences e Speed Dial Number Display Style Name e Function Keys Tone Schemes Germany x 16 snom PA1 User Manual Initializing and Configuring the PA1 3 In the General Information section
12. 6 Appendix 2 GNU General Public License COPYRIGHT NOTICE AND WARRANTY DISCLAIMER Das Produkt enth lt Software die unter der GNU General Public License Version 2 frei genutzt werden darf This Product contains Software applicable to GNU General Public License Version 2 which can be used freely Im Verh ltnis zu den Lizenzgebern der Software gilt der folgende Haftungsausschluss Towards the licensor of this Software the following liability is disclaimed This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE See the GNU General Public License for more details Der Lizenztext der GPL lautet wie folgt The GNU General Public License is as follows GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 59 Temple Place Suite 330 Boston MA 02111 1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other pr
13. Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EIT
14. HER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs lf you develop a new pro ram and you want it to be of the greatest y p prog y g possible use to the public the best way to achieve this is to make it free software which everyone can redistribute and change under these terms To do so attach the following notices to the program Itis safest to attach them to the start of each source file to most effectively convey the exclusion of warranty and each file should have at least the copyright l
15. Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or b Accompany it with a written offer valid for at least three years to give any third party for a charge no more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source cod
16. URL is specified on the PA1 s web interface or by means of a manual update CAUTION Cutting off the device s power during a firmware update red LED on green LED off will damage the firmware and render the PA1 inoperational In such a case the PA1 will need to be returned to the vendor for a reset special kit required Do NOT remove the device s power supply Ethernet cable when using PoE power adapter when not using PoE when the red light is on or blinking a firmware update is ongoing LED indications Ready or busy Off On Blinking During firmware update Firmware update initiated On On Red LED comes on automatically or manually DO NOT TURN OFF POWER Firmware update in progress On Off Green LED turns off Blinking Off Do not turn off the power until On IL Off the green LED comes back on Off Off On off Blinking Off On Off FW update completed ready Off On Red LED turns of green LED comes on Fig 1 Provisioning software updates Provisioning of updates can be done in two ways Fully automatic with the setting Update automatically Whenever a new firmware version is made available the settings are downloaded from the settings server and the update is started automatically Semi automatic with the setting Ask for update The settings are downloaded from the settings serve
17. application to Version 8 7 3 19 Recovery Latest V8 Beta Image 8 7 4 8 f The Firmware V8 PA1 page opens Right click on the version s link then click on Copy shortcut in the context menu Firmware V8 PA1 Firmware V8 1 Check the feature list of Version 8 7 3 25 carefully V8 4 2 Check the release notes for version 8 7 3 25 carefully 3 Check the change log for firmware branch 8 X carefully e 4 Check the Known Issues section for 8 7 3 25 carefully 5 Perform the update from V8 X to Version 8 7 3 25 following the steps below o Right click on the following link and choose Copy shortcut e snomPA1 8 7 3 25 rox 3 MByte amp http provisioning snom com download fw snomPAl Open the Web Use 7 3 25 SIP f bin page g On the Manual Software Update page of the PA1 place the cursor into the textfield of Firmware right click and click on Paste Manual Software Update Firmware Load Undo Your phone is shipped with a valid license prein the manual license upload to enable additional license in case it s missing or damaged If the uj MAC address of the phone it will be ignored an Delete Copy Paste ti 4 Click on Load The PA1 starts the firmware update indicated by the red LED lighting up and the green LED going out The firmware update is done when the red LED goes out and the green LED comes back on CAUTION Cutting off the device s power during a firmware update red LED
18. bited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 If as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain
19. e means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions 28 are prohi
20. eaker Volume Enter a number between 1 low and 14 high in the text field The default setting is 10 Amplifier Gain Enter O or 1 in the text field The default setting is 1 Click on Apply at the bottom of the page After clicking on Apply the Save button will appear at the top of the page Click on Save to save the changes permanently in case of power loss 17 snom PA1 User Manual Using the PA1 Using the snom PA1 Making announcements Dial the phone number of the PA1 and when your phone shows that you are connected speak your announcement into its handset headset casing microphone When you are done terminate the call by hanging up or pressing the h xl key Turning the loudspeaker on or off 1 Open the PA1 s web interface 2 Click on Preferences in the menu on the left side of the window page The Preferences page opens 3 In the PA1 Controls section click on the radio buttons on off to turn the loudspeaker on or off PA1 Controls Use reset button for dialing Oon Gort D I Phone ends call after set seconds 300 Speaker Volume 1 14 10 Amplifier Gain 1 Speaker on Ooff e 4 Click on Apply at the bottom of the page Then click on Save at the top of the page to save the changes permanently in case of power loss 18 snom PA1 User Manual Software Update Software update Software updates can be done through provisioning from the server whose setting
21. entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The
22. further software development If you are interested in this package please talk to your vendor 5V power adapter PSAC10R 050 available separately snom PN 00002730 Loudspeaker Keyboard Network cable snom PA1 User Manual Setting Up Setting up the snom PA1 Delivery Content II Tu PIPPP SSSS o Base unit 2 brackets for wall mounting pre assembled 4 screws 8 mm length 16 mm 4 expansion anchors for wall mounting o Cable set 4 proprietary snom cables for connecting periphery devices o Quick Start Guide Wailmounting Note The Ethernet cable must not be bent to avoid damage and loss of the network connection We recommend that you place the PA1so that the PoE connector is facing toward the LAN port in your network We also recommend that you place the PA1 in a location where you can see the LEDs from your desk or work station 110 mm 4 331 121 mm 121 mm 4 764 110 mm 4 331 gi Fig 1 snom PA1 User Manual Setting Up 1 Use the measurements in Fig 1 to mark the positions of the four holes to be drilled in the wall or use the template at Appendix 1 Drill the holes and insert the expansion anchors in the holes Place the snom PA1on the wall with the cut outs above the anchors as shown in Fig 2 Fig 2 4 Place the screws in the anchors and tighten them evenly Connecting the PA1 md BEN gu t Fig 2
23. ine and a pointer to where the full notice is found lt one line to give the program s name and a brief idea of what it does gt Copyright C lt year gt lt name of author gt This program is free software you can redistribute it and or modify it under the terms of the GNU General Public License as published by the Free Software Foundation either version 2 of the License or at your option any later version This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE See the GNU General Public License for more details You should have received a copy of the GNU General Public License along with this program if not write to the Free Software Foundation Inc 59 Temple Place Suite 330 Boston MA 02111 1307 USA IV Den vollst ndigen korrespondierenden Sourcecode der Software schickt Ihnen die snom technology AG auf Nachfrage gerne auf einem blichen Datentr ger gegen Erstattung der Herstellungskosten in H he von EUR 5 zu Der vollst ndige korrespondierende Sourcecode kann auch ber unsere Website unter http www snom com gpl_ html amp L 0 herunter geladen werden 29 If requested by you the complete corresponding source code of the Software can be sent by snom technology AG on a standard data storage medium against the reimbursement of the manufacturing costs of EUR 5 per unit The comple
24. ing or into the email if Support has asked you to contact them by email Make sure to delete the MAC address and the IP address if the posting or e mail can be read by the public System information Open the phone s web interface Status Settings Make sure to delete private and or security relevant information like the MAC address public IP address etc Traces snom Support may ask you to submit a SIP Trace and or a PCAP Trace to help them analyze your problem Performing a SIP Trace 1 Open the phone s web interface Status SIP Trace Click on Clear to clear the page Recreate the error to be documented in the trace Click on Reload Copy the text and submit to Support in whatever form they requested you to use a fF o N Performing a PCAP Trace ch Open the phone s web interface Status PCAP Trace Click on Start to start recording network traffic Click on Stop to end recording Click on the here link to open the file download window and save the file a kf oO N Submit the file to Support in whatever way they requested you to use 25 Appendix 1 Drilling Template PA1 Wallmounting 25 00 mm 110 00 mm snom VoIP phones PRINT FULL SCALE 100 min 8 00 mm max 6 00 mm Recommended shape of screw head max 5 00 mm 121 00 mm Use screws and expansion anchors suitable for your wall 2
25. king a firmware update is ongoing Cutting off the device s power during a firmware update red LED on green LED off will damage the firmware and render the PA1 inoperational In such cases it will need to be returned to the vendor for resetting SEV Safety Extra Low Voltage compliance Safety status of Input Output connections comply with SELV requirements Warning To avoid electric shock do not connect safety extra low voltage SELV circuits to telephone network voltage TNV circuits LAN ports contain SELV circuits and PSTN ports contain TNV circuits Some LAN and PSTN ports both use RJ 45 BP8C connectors Use caution when connecting cables snom PA1 User Manual Safety Disposal Cleaning of Product Standards conformance Ce FC This device complies with the essential health safety and environmental requirements of all relevant European directives The declaration of conformity can be requested from snom address see reverse cover This phone is FCC certified and meets US health safety and environmental standards Unauthorized opening changing or modifying the device will cause the warranty to lapse and may also result in the loss of CE conformity and the FCC certification In case of malfunction contact authorized service personnel your seller or snom Disposal of the device A This device is subject to European Directive 2002 96 EC and may not be disposed of with general household garbage The separate co
26. lect Never update do not load settings from the list box of Update policy Click the off radio button of PnP Config Click on Apply at the bottom of the page Then click on Save at the top of the page to save the changes permanently in case of power loss Click Reboot and confirm with Yes Updating manually 1 Open the PA1 s web interface 2 Click on Software Update in the menu on the left side of the window page The page Manual Software Update opens 20 snom PA1 User Manual Software Update Manual Software Update gt hes Operation Home You may explicitly specify which software version you want to run on this phone Fill in the http URL Directory which is pointing to the firmware you want to use Please use only a complete http URL like Setup http www snom com download share snomXXX YYY bin The phone will reboot after you press Prefersnced the load button Speed Dial Function Keys Manual Software Update Identity 1 Firmware Identity 2 Load Identity 3 3 Enter the firmware link in the text field of Upload Setting file manually Obtaining the firmware link a Open snom s web page at www snom com b Click on Support Download Firmware Solutions pport Partners Company Step 1a Knowledge Base FAQ Search Step 1b Visit our Knowledge Base Step 1c Go to our FAQ Step 1d Visit our Forum Firmware Release Wtes Update Licenses c The Wiki page Category Firmware opens
27. llection and proper disposal of electrical and electronic devices serve to protect human health and the environment as well as to use and reuse resources prudently and rationally If you do not know where you may dispose of the device at the end of its lifespan contact your municipality your local waste management provider or your seller Cleaning To clean the device use an anti static cloth Please avoid cleaning liquids as they might damage the surface or internal electronics of the device snom PA1 User Manual Standard Feature List Standard feature list EEE 802 3af PoE compliant Class 3 2 port 10 100Mb Ethernet switch SIP or multicast support Remote SW update Network web management Remotely settable speaker volume adjustment Push on speaker terminals Class D 4W power amplifier loudspeaker not included IP address reset button Call network activity indicator One MIC in and one LINE out 3 5 mm connector for headset connection SPK impedance 150 Ohm MIC power supply 3 3V RL 2 KOhm S 42 dB 2dB Microphone input must be differential and without grounding This port is for installation and maintainance purposes only not for the connection of other devices 4 O pins remotely settable via web interface in administrator mode only or o with DTMF tones with programmable timer Robust casing design for wall mounting Not included BSP board support package for
28. n URL Settings DNS Advanced Domain snom com Certificates ANG Canine te Fass E 7 Inthe Network section make the following changes a DHCP setting Click on Off b IP address and Netmask settings Replace default values with network values c Other settings Replace if and as required 8 Click on the Apply button at the bottom of the page Note Any changes you make will not take effect until you click on Apply Changes will be lost if you open another page of the web interface or if you close the web interface without first clicking on Apply 9 After you have clicked on Apply three buttons will appear at the top of the page Operation Home A Apply setting changes Reboot Directory D A Some settings are not yet stored permanently Save View Changes Preferences Speed Dial Network Behavior Audio SIP RTP QoS Security Update Function Keys j Network Identity 1 DHCP Son Ooff wegen 2 Options on DHCP on 1346 12 15 42 43 51 66 67 1 Merit 3 Options on DHCP off 43 120 125 Hee IP address 10 110 25 154 Action URL Settings Netra 255 255 255 0 Advanced Host Name Certificates IP Gateway 10 110 25 254 o Software Update a Note Changes that have not been saved will be I or is disconnected from its power source Click on the Save button to save the changes permanently ost if and when the phone loses power Operation Home A Apply setting changes Reboot Director
29. ogram whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Library General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights 27 We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software
30. r automatically but you are prompted to confirm any available update 1 Open the PA1 s web interface 2 Click on Advanced in the menu on the left side of the window page The Advanced Settings page opens 19 snom PA1 User Manual Software Update 3 NOS Click on the Update tab Network Behavior Audio SIP RTP QoS Security Update Update Update Policy Update automatically Setting URL http provisioning snom com Settings refresh timer 0 PnP Config gon opt Apply Reset Reboot Select Update automatically or Ask for update from the list box of Update policy Enter the settings server s URL in the text field of Setting URL Click the on radio button of PnP Config Click on Apply at the bottom of the page Then click on Save at the top of the page to save the changes permanently in case of power loss Manual software update If the current setting is updating through provisioning whether automatically or semi automatically you must first change these settings Settings 1 2 Open the PA1 s web interface Click on Advanced in the menu on the left side of the window page The Advanced Settings page opens Click on the Update tab Network Behavior Audio SIP RTP QoS Security Update Update Update Policy Never update do not load settings v Setting URL Settings refresh timer 0 PnP Config Oon Hoff Apply Reset Reboot Se
31. select your country from the drop down list of Tone Scheme Click on Apply at the bottom of the page After clicking on Apply the Save button will appear at the top of the page Click on Save to save the changes permanently in case of power loss Automatic termination of calls This setting determines after how many seconds calls to the PA1 will be terminated The default setting is 300 seconds 1 Open the PA1 s web interface 2 Click on Preferences in the menu on the left side of the window page The Preferences page opens 3 In the PA1 Controls section enter the number of seconds in the text field of Phone ends call after set seconds PA1 Controls Use reset button for dialing on Sept D Phone ends call after set seconds 300 Speaker Volume 1 14 10 Amplifier Gain 1 Speaker on Ooff e Click on Apply at the bottom of the page After clicking on Apply the Save button will appear at the top of the page Click on Save to save the changes permanently in case of power loss Operation Home A Some settings are not yet stored permanently Save View Changes Directory Adjusting the volume and the amplifier gain 1 Open the PA1 s web interface 2 Click on Preferences in the menu on the left side of the window page The Preferences page opens 3 You can change the default settings for speaker volume and amplifier gain in the PA1 Controls section o Sp
32. sen Eed 17 Adjusting volume and amplifier c albi anere dree 17 Using the snom PAI eeeeeeeeeeeeeeeseeesenn nnn anna nna tuna tunt amnia rasa aano suns sm nass asma ERAN 18 Making anode E EE 18 Turning the loudspeaker On Or E 18 S ftware update 19 PROVISIONING Ee 19 Man al software pdate 3e neret reb e rp epa rr ep sake ae ape as a 20 fisse c ARKAD 20 Updatihd Ra EE 20 FRE DOO pc E 23 Hardireboot TE 23 Re setto factory E 24 Contacting snbm SUP PO e 24 Dici m 25 Appendix 1 Drilling Template PA1 Wallmounting EEN 26 Appendix 2 GNU General Public License sse 27 snom PA1 User Manual Copyright Trademarks GPL Disclaimers Copyright Trademarks GPL Legal Disclaimers 2013 snom technology Aktiengesellschaft All Rights Reserved snom the names of snom products and snom logos are trademarks owned by snom technology AG All other product names and names of enterprises are the property of their respective owners Product specifications are subject to change without notice snom technology AG reserves the right to revise and change this document at any time without being obliged to announce such revisions or changes beforehand or after the fact Texts images and illustrations and their arrangement in this document are subject to the protection of
33. side its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License
34. sn om snom com VoIP phones snom PAT User Manual TABLE OF CONTENTS Copyright Trademarks GPL Legal Disclaimers enne 4 IMpPOrtant INFOMMATION esee 5 Safety cue Ne dera a 5 SELV Safety Extra Low Voltage compliance EE 5 SLANG ALGS COMMON AMOS T p ee 6 Disp sal Gt the devigE annsin aa ai ena a ieli 6 Cleaning EE 6 Standard feature list ssssusnennennnnnnnnnnnnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn RR AR AR RAR 7 Setting up the snom P 1 s smsssssmsts etsssri sscssssss t k sbenasssskap nsskensanass ensskssskssanseksk bokens 8 Delivery Conterit svisrs sossar skinnar nens FR rar Aa DNA Rag ANA SR ANEDN SKAR araa ANNAE AKAA E ONA SR GSR anaa 8 Mali rcu MEE ieee dnd noter bcr dca id cdd cibo KAS ind 8 COMMECHING TNE PAT c 9 Initializing and Configuring the PA ssssessussnsnnunonnnnnnnnnnnnunnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnn annann nnna 10 e Menem TR T aRNORaNN EES 11 Initializing with DHO aene 11 Initializing Without DAC Popri aa na a rii 11 SECUN Le 13 Configuring aCCOUNTS eebe Eege 15 Configuring identities automatically 25 tris paci datura pk cake anre pk ri Rh 15 Configuring identities manually een 15 jap T 16 HME ZONE cud dot need Mee d DS 16 ee Ne 16 Automatic termination of CAME s vi0s vmsursswisikesas vises issn r
35. sword you cannot open the PA1 s web interface If you do not wish to set an HTTP password click on the respective button to turn off the reminder until the next reboot or permanently If you change your mind later you can set the password on the PA1 s web interface Advanced page gt QoS Security tab gt HTTP Server or turn off the warning later at Advanced gt QoS Security gt Security gt Ignore security advices Continue with Configuring accounts on page 15 Firmware versions 8 7 4 and higher When you register the first account the SIP user name and password will be registered as the HTTP user name and password If you wish to change them later you can do so on the PA1 s web interface gt Advanced gt QoS Security gt HTTP Server Note If you do not replace the default administrator password by an individual one an unauthorized third party could set an administrator password unknown to you In sucha case you would no longer be able to switch from user mode to administrator mode If you set your own passwords be sure to write them down and store them in a secure place Without the administrator password you will not be able to switch the web interface from user mode to administrator mode the settings will be inaccessible Without HTTP password you cannot open the web interface Continue with Configuring accounts on page 15 14 snom PA1 User Manual Initializing and Configuring the PA1 Configuring accoun
36. te corresponding source code of the Software can also be downloaded from our web site http www snom com gpl_ html amp L 0 Vi Weitere Informationen finden Sie auch unter http www snom com For further information see http www snom com snom technology AG Wittestr 30 G 13509 Berlin Deutschland Tel 49 30 39 83 3 0 Fax 49 30 39 83 31 11 info snom com sales snom com snom technology Inc 18 Commerce Way Suite 6000 Woburn MA 01801 USA Tel 781 569 2044 Fax 978 998 7883 infoUSA snom com snom UK Ltd Amethyst House Meadowcroft Way Leigh Business Park Leigh Manchester WN7 3XZ UK Tel 44 169 348 7500 Fax 44 169 348 7509 uksales snom com snom VoIP phones snom France SARL 6 Parc des fontenelles 78870 Bailly France Tel 33 1 80 87 62 87 Fax 33 1 80 87 62 88 snom fr snom com snom technology SRL Via A Lusardi 10 20122 Milano Italia Tel 39 02 00611212 Fax 39 02 93661864 snom italy snom com snom technology Ltd Rm A2 3F No 37 Ln 258 Ruiguang Rd Neihu Dist Taipei City 114 Taiwan Tel 886 2 8751 1120 Fax 886 2 8751 1130 infoASIA snom com Your specialist retailer Ihr Fachhandler Votre distributeur Su distribuidor ll tuo rivenditore 2013 snom technology AG V1 00 snom com FE CE Z
37. ts The PA1 supports up to four accounts or identities as they are called on snom devices that can be used to make announcements over the loudspeaker connected to the PA1 Configuring identities automatically recommended by using the provisioning server For more details on auto provisioning snom devices see www snom com wiki Configuring identities manually In the menu on the left click on Identity 1 The page Configuration Identity 1 opens with the Login tab active Configuration Identity 1 p Zeg oS Operation Home Login SIP NAT RTP Directory Login Information Setup Identity active Son Oot Preferences Displayname e Speed Dial Account 152 Function Keys Password pepp Q Registrar Rm EEN a Outbound Proxy Identity 3 d Identity 4 Failover Identity None Action URL Settings EE Advanced Mailbox Certificates Ringtone Ringer 1 6 Software Update Custom Melody URL E Status Display text for idle screen System Information Ring After Delay sec Log Record Missed Calls gon ep SIP Trace Record Dialed Calls Son Ooff D I DNS Cache Record Received Calls Bon off Subscriptions Identity is hidden Don Goff PCAP Trace Memory Apply Re Register Play Ringer Settings Remove Identity Remove All Identities 1 Enter the data required by your network in the text fields o Account Name
38. tton Open the web interface Open the web interface Advanced Network DHCP Off Change settings IP address and Netmask Click on Apply and Save firm by clicking on Yes Apply setting changes Click on Reboot and con After reboot has been completed Register the first account J Account registered LED indications when application is running Ready Busy J d Firmware update in progress 10 Off On j Red LED lights up Off Blinking Red LED starts to blink Blinking Off Red LED stops blinking glows steadily Off On Green LED lights up Note When the red and the green LED are on simultaneously pressing the IP Reset button will result in the announcement of the IP address Caution Pressing the button at other times will result in resetting the PAT t can take a few minutes until the application starts 2 Via external loudspeaker or headset Ask your administrator for the settings required in your net work It may also be necessary to change other settings as well Off On Red LED turns off Off On Off Blinking Off On snom PA1 User Manual Initializing and Configuring the PA1 nitializing After the PA1 has been connected to the network via Ethernet cable the red LED marked Power
39. ty relevant information there This includes MAC addresses SIP headers etc that may allow others to hack into your system or use your identity for nefarious purposes If you haven t received an answer or solution within a reasonable amount of time generally two work days send the link to your posting to Support You need to create a support account first if you don t already have one Creating a support account 1 Open snom s web page at www snom com Click on the Support tab to open the Support window Click on End Customer Support On the Support Center page click on Register new account Fill out the form and click Register You will receive an automatic email Click on the link to activate your account NO BR ON You will receive a second email containing your account name email address and password You can now submit tickets requesting support to snom Support Submitting a ticket 1 Open snom s web page at www snom com Click on the Support tab to open the Support window Click on End Customer Support On the Support Center page enter your email address and password and click on Login Click on Ask for support o ok o H Follow the instructions on the screen 24 snom PA1 User Manual Troubleshooting Submitting system and settings information System information 1 Open the phone s web interface gt Status gt System Information 2 Copy the text under System Information into your forum post
40. uct Important information Please read the instructions on safety and disposal and on how to set up and use the device before using it and also give them to other users to read or inform those users of their contents Save this manual and do not give the device to third parties without it Satety instructions Follow the instructions in this manual and other applicable documentation of the device If the device is not supplied with power via an Ethernet cable use only a power adapter expressly recommended by snom technology Other power supplies may damage or destroy the device affect its behavior or induce noise Avoid placing the cables where people may trip over them or where they may be exposed to mechanical pressure as this may damage them This device is for indoor use only NOT FOR OUTDOOR USE Do not install the device in rooms with high humidity for example in bathrooms laundry rooms damp basements Do not immerse the device in water and do not spill or pour liquids of any kind onto or into the device Do not install the device in surroundings at risk for explosions paint shops for example Do not use the device if you smell gas or other potentially explosive fumes Do not use the device during thunderstorms Lightning striking the power grid may cause electric shocks Do NOT remove the device s power supply Ethernet cable when using PoE power adapter when not using PoE when the red light is on or blin
41. will light up The PA1 begins to boot Initializing with DHCP The snom PA1 has a built in DHCP client When DHCP is available in the network the PA1 will initialize automatically 1 The red LED begins to blink The PA1 is sending the DHCP request 2 After the PA1 has received an IP address and other network related settings netmask IP gateway DNS server etc from the DHCP server the red LED stops blinking and glows red steadily indicating that the application is starting up 3 When the PA1 boot up process is finished and the web interface is available the green LED lights up in addition to the red one 4 Briefly press the button labelled IP Reset to listen to the oral announcement of the IP address in English over the loudspeaker or headset 5 Open a web browser on a PC connected to the same network as the PA1 Type the IP address into the address bar after http and press Enter to open the PA1 s web interface 7 Continue with Security settings on page 13 Initializing without DHCP If your network does not support DHCP the snom DAT will boot with the default settings Please obtain the network IP address and netmask and if applicable other required network settings from your network administrator The default settings are IP address 192 168 0 2 Netmask 255 255 0 0 1 The red LED begins to blink The PA1 is sending the DHCP request 2 Press the button labelled IP Reset The red LED continues to
42. y Setup Network Behavior Audio SIP RTP QoS Security Update Preferences N He Spaad Dial DHCP on Ooff Function Keys Identity 1 Options on DHCP on Ontinns on DHCP off b Click on the Reboot button The Confirmation 12 1346 12 15 42 43 51 66 67 1 42 355 ane 1 page will appear snom PA1 User Manual Initializing and Configuring the PA1 Confirmation i Operation Home Attention Directory Are you sure you want to reboot the phone Setup Preferences Yes No Speed Dial Fiatin Weg c Click on Yes The PA1 will save the new settings and restart When the start up with the network settings is complete the red and the green LED will both be glowing steadily 10 Continue with Security settings Security settings When the web interface is opened for the first time upon initialization you will see the Security page Security M Operation Home Security Advice Directory Seis We strongly recommend that you secure the web interface in order to protect your phone against s l remote attacks Therefore the HTTP User and Password as well as the Administrator Password Preferences should be changed from the default value Speed Dial Function Keys Security Identity 1 Administrator Password eecceees Identity 2 Administrator Password Confirmation Identity 3 Identity 4 HTTP Server e Action URL Settings ilm Advanced Password EEGEN
Download Pdf Manuals
Related Search