VN-V225VPU VN
Contents
1. Hold the dome cover over the lens and check the focus 7 Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram and tighten the fastening screw of the focus adjustment ring 8 Set the MONITOR OUT selector switch to OFF then press the RESET button shortly less than 2 seconds e The camera restarts and the focus assist mode is released Knob Catch B A Zoom adjustment ring Focus adjustment ring Focus adjust gear Knob B Catch A e One base pitch Mounting the Dome Cover 1 Mount the inner dome to the catches x3 2 Mount the dome cover Remove and clean any dust or dirt on the dome cover Align the base with the position alignment marks x3 on the dome cover and mount the dome cover Tighten and secure the dome cover fastening screws x3 g LLK Poon algment mar fr __ Catches x3 Inner dome Wrench provided Note Check that the silica gel Provided has been inserted before mounting the dome cover Ensure that the dome cover is secured Insecure mounting may increase humidity fog up the camera or the cover may drop When the cover is removed again after mounting the dome cover check the field angle and re adjust the focus and field angle if necessary Make sure that the fall prevention wire of the dome cover is not caught between the dome cover and the base Otherwise the anti dust and waterproof2. e Select in the sequence of Settings Control Panel Network and Sharing Center Manage network connections 2 The computer on which Internet Explorer is launched automatically selects the connected network e Right click and select Properties Check to ensure that the Client for Microsoft Networks and Internet Protocol TCP IP check boxes are selected Windows Vista Check to ensure that the Microsoft Network Client and Internet Protocol Version 4 TCP IPv4 check boxes are selected 3 Select Internet Protocol TCP IP and click Properties Windows Vista Select Internet Protocol Version 4 TCP IPv4 and click Properties 4 Set the IP address Select Use the following IP address D Specify the IP address For example use 192 168 0 100 when the camera is in its default settings Memo Make sure that you take note of the original IP address before altering e Ensure that a duplicate IP address is not specified within the same network environment Set Subnet mask to a value that is appropriate for the setting operation Consult the network administrator if you have any queries Use 255 255 255 0 when the camera is in its default settings When a Default gateway is present make use of the corresponding IP address e g 192 168 0 254 Click OK Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your netw
3. 2009 Victor Company of Japan Limited LST0849 001B
4. Mi Power cable Connection distance when using 2 core VVF cable Reference values Conductor diameter mm 91 0 and above 91 6 and above 92 0 and above Maximum connection distance m 130 340 540 Maximum connection distance m with 40 120 180 Heater KA ZH215U Caution The rated power of this product is AC 24 V 50 Hz 60 Hz Make sure to use it with the correct voltage Be sure to use an AC 24 V supply that is insulated from the primary power source Supplying a power beyond the rated value may result in failures smoke or fire If the camera breaks down turn off the power and contact our service center immediately When a power beyond the rated value is supplied the internal components may be damaged even if no abnormality is found on the appearance and operation of the camera Please send to your nearest JVC dealer immediately for servicing charged separately 5 Wind the waterproof tape Note e For cables that are not used be sure to wrap the ends individually with insulating tape Ue Ge Space for heater rx Memo LNs When mounting the heater unit sold WN A separately KA ZH215U please refer to DN the KA ZH215U INSTRUCTIONS 1 2 4 5 10BASE T 100BASE TX PoE 3 aii eee ROB Solder welding Wind the or crimping waterproof tape S g Wind the insulation tape LAN cable LAN cable stopper x2 Processes after con
5. custom settings J Cee Reset to Medium low 5 Disable pop up block Connection of the camera cannot be established when pop up block in the Internet Explorer is set to Enable Follow the steps below to set the pop up block to Disable e Selecting Tool Pop up Blocker Turn Off Pop up Blocker permits all sites e To allow only specific sites such as this unit select Tool Pop up Blocker Turn Off Pop up Blocker followed by selecting Tool Pop up Blocker Pop up Blocker Settings which becomes active to open the Pop up Blocker Settings window In the opened window add the address of the camera as a permitted web site address 6 When plug in tools such as the Yahoo or Google toolbar are included in the Internet Explorer disable the pop up block function of these plug in tools as well Step3 Connecting the camera to the computer Launch the Internet Explorer Enter the IP address of the camera http 192 168 0 2 for example Click Go about blank M rosoft Internet Explorer jen avorites Tools Help a id a a Psearch Fate O A 3 BD Addr 5 http i 192 169 0 2 Opening page http 192 169 0 2 Memo e f the proxy server settings for access to the Internet via the Internet Explorer is enabled you may not be able to specify the IP address directly In this case change the proxy settings of the Internet Explorer To open the Basic
6. function may not work properly v Continued Setting IP Address Settings This section is a description based on Windows XP IP address setting procedure Follow the procedure below to configure the IP address of the camera Step1 IP address setting at the computer Set the IP address of the computer that is used for configuring the camera settings v Step2 Internet Explorer settings Configure the Internet Explorer settings in order to establish connection between the computer and the camera v Step3 Connecting the camera to the computer Connect the computer to the camera v Step4 IP address setting for the camera Set the IP Setting item on the Basic Settings1 screen to DHCP Disable or DHCP Enable Step1 IP address setting at the computer Camera at factory default is set to DHCP Disable DHCP client function is Off it will activate under the following IP address after startup Set the computer to an IP address that enables communication with the following For example set the IP address to 192 168 0 100 and subnet mask to 255 255 255 0 IP address 192 168 0 2 Subnet mask 255 255 255 0 Default gateway None E IP address setting at the computer Set the computer to an IP address that enables communication with the camera 1 Click Start Select in the sequence of Control Panel Network Connection Local Area Windows Vista
7. JVC FIXED IP DOME CAMERA Vandal Resistant FIXED MEGAPIXEL IP DOME CAMERA Vandal Resistant VN V225VPU READ ME FIRST VN X2 35 V P U LST0849 001B VN X235VPU is a high definition surveillance camera that uses high resolution CCD sensors with 4 times the pixel count of VN V225VPU Thank you for purchasing this JVC product Before operating this unit please read the instructions carefully to ensure the best possible performance E This manual contains the basic instructions for using this unit Please refer to INSTRUCTIONS Setting pdf and INSTRUCTIONS Installation pdf in the CD ROM supplied with this product for description on the detailed usage of this unit For the latest information please refer to the README file in the CD ROM supplied with this product e The supplied CD ROM includes INSTRUCTIONS Setting pdf NSTRUCTIONS Installation paf API Guide pdf VSIP Guide pdf and Search tool White Spot Correction Tool E How to read this READ ME FIRST e JVC holds the copyright to this manual Any part or all of this manual may not be reproduced without prior consent from the company e Windows is a registered trademark of Microsoft Corporation in the U S e Product names of other companies described in this manual are trademarks or registered trademarks of the respective companies Symbols such as and are omitted in this manual e Design specifications and other contents des
8. Settings1 page without going through the built in viewer enter the URL of the Basic Settings1 page in the address field of the Internet Explorer e VN V225VPU http 192 168 0 2 cgi in v225display cgi v225basicmenu1 html e VN X235VPU http 192 168 0 2 cgi in x235display cgi x235basicmenu1 html e After the Security Settings screen appears press the OK button to proceed E if the IP address is unknown IP address settings cannot be changed by accessing via a computer when the IP address of the camera is unknown You can use the following method to identify the IP address e Search using the Search tool inside the TOOL_E folder of the supplied CD ROM x For details on Search tool please refer to the README file in the CD ROM supplied with this product 2 Enter the user name and password login as administrator Enter the user name This is set to admin by default Enter the password This is set to jvc by default Click OK User name Password Memo e After the Security Settings screen appears press the Yes button to proceed 3 Built in Viewer and the operator password entry screen appear Enter the Operator Password default password is jvc Click OK Image Settings PTZ Settings PTZ Control Ee iove I GoTd DEE DEN mE Step4 IP address setting for the camera 1 Click Details of the Built in Viewer Image Setti
9. TX network interconnected using devices such as an IEEE802 3 compliant switching hub e EEE802 3af compliant switching hub when PoE is used e IGMPv2 compliant network when multicast is in use Memo e To use MPEG4 images on the built in viewer install the open source codec ffdshow You can download ffdshow from the Internet JVC is not responsible for any damages resulting from your use of open source software Specifications AC 24 V 50 Hz 60 Hz or PoE DC 48 V AC 24 V 50 Hz 60 Hz when KA ZH215U is in use AC 24 V 0 35 A PoE 7 0 W AC 24 V 1 0 A when KA ZH215U is in use Mass Approx 1 3 kg 2 87 Ibs Ambient temperature 10 C to 50 C operation 0 C to 40 C recommended When KA ZH215U is in use 30 C to 50 C operation 20 C to 40 C recommended 35 RH to 90 RH without condensation Supply voltage Current consumption Ambient humidity E Accessories e SAFETY PRECAUTIONS e Service Information Card For USA e Read Me First Template e CD ROM Wrench e Warranty Card For USA Silica gel E Dimension Unit mm inch 121 4 3 4 113 4 1 2 G3 4 14 UNC screw for piping side 42 1 5 8 G3 4 14 UNC oe for piping bottom 160 6 1 4 x Specifications and appearance of this unit are subject to change for further improvements without prior notice
10. cribed in this manual are subject to change for improvements without prior notice E The latest version Please visit VINETWORKS web site to check the latest firmware at http www jvc victor co jp english products e html The latest firmware can be found on VINETWORKS download page Installation Mounting the Camera Setting Up the Camera Remove the dome cover with the wrench provided Screws x3 2 Grab the inner dome and remove it from the catches x3 Inner dome Wrench provided z Dome Fall cover prevention Catches wire x3 not Camera removable Mounting the Camera Mount the camera to the ceiling or wall To mount on a wall perform the same procedures below but replace the word ceiling with wall I Use the provided template to make a 230 mm 1 1 8 inch hole in the ceiling 2 Mount the fall prevention wire that connects the camera to the ceiling x Fall prevention wire is not provided Prepare a wire with due consideration of the length strength pull factor and material insulative Unscrew the mounting screw for the fall prevention wire beneath the camera and mount the fall prevention wire Mount the fall prevention wire to a strong location 3 Mount the camera to the ceiling Pull out the cables from the ceiling and the cables from the camera towards the lens as shown face the mark in the shooting direction then mount the camera to t
11. elow to enable it Select Trusted sites under Tool Internet Options Security Upon doing so the Sites button directly below becomes active Click this button deselect the check in the displayed window and add the following web site to the zone http 192 168 0 2 When the camera is in its default settings e Next select Trusted sites under Tool Internet Options Security and press the Custom Level button Select Enable under Scripting Active script of the Security Settings window that is opened Security Settings Settings Active scripting Disable Prompt Allow paste operations via script O Disable Enable O Prompt Scripting of Java applets v gt Reset custom settings Reset to Medium a 4 If ActiveX controls and plug ins of the Internet Explorer is disabled follow the steps below to enable it e Click Trusted sites under Tool Internet Options Security Select the Custom Level button to open the Security Settings window Set all items under ActiveX controls and plug ins in the opened window to Enable Enable also Allow Script initiated window without size or position constraints under Miscellaneous Security Settings Settings E Activex controls and plug ins W Automatic prompting for Activex controls O Disable Enable Binary and script behaviors Administrator approved v lt gt Reset
12. he ceiling To mount on a wall mount the camera such that the mark is facing upwards x Screws for mounting the camera are not provided Use the appropriate type of screws according to the material of the location for mounting W Fall prevention wire 930 mm 1 1 8 inch Base Shooting direction mark 6 mm and below 12 mm and below n 04 1 6 5 mm Note e To mount the camera using electrical box or piping please refer to INSTRUCTIONS Installation in the bundled CD ROM Cable Connection For safety reasons turn on the power only after all the connections are completed When power is supplied to the camera the STATUS indicator lights up The indicator lights up in orange during startup and turns green when startup is complete Connect the alarm cable Connect the alarm cable to an external device such as a sensor or buzzer Alarm cable to use Recommended shield cable Length of 50 m or shorter e UL1007 UL1015 or equivalent products AWG 22 to AWG 18 or equivalent products 2 Connect to audio cable Recommended shield cable 3 Connect the LAN cable x To use the PoE power supply connect to a PoE compatible device and supply the power from the LAN cable Note e When using a heater unit sold separately KA ZH215U PoE power supply does not work for the heater unit KA ZH215U Be sure to use an AC 24 V power supply e Connecting to HUB Use a st
13. hold the RESET button for less than 2 seconds e The camera reboots approximately 1 minute e During the restart the STATUS indicator lights up in orange Set to N when connecting to a NTSC monitor or set to P when connecting to a PAL monitor 3 Adjust the shooting direction of the camera Adjust the camera for pan tilt and rotation and face the camera towards the subject MONITOR OUT selector switch MONITOR terminal STATUS indicator RESET button JON Shooting direction mark Pan center mark Tilt fastening screw Memo e Rotate both pan and rotation 175 from the positions aligned with the camera s shooting direction mark pan center mark and rotation center mark Be sure to hold the rotation control and adjust the rotation without holding the lens section e After adjusting the field angle tighten and secure the tilt fastening screw so that the field angle will not be misaligned Note Moving the camera when it has exceeded the adjustment range may cause its performance to deteriorate As the tilt and rotation range of this unit is wide part of this unit may be reflected in the shooting screen depending on the field angle and direction e Do not hold the lens section when adjusting the camera direction The lens section may be damaged if you apply force to it 4 Adjust the image size Loosen the fastening screw of the zoom adjus
14. lay and open the Display Properties window Click the Settings tab in the Display Properties window followed by the Advanced button Check that DPI setting in the General tab has become Normal size 96DPI Otherwise change the setting to Normal size 96DPI and reboot Windows v Setting Using Internet Explorer Configure the picture quality setting alarm setting and other settings using the Internet Explorer x For details please refer to INSTRUCTIONS Setting pdf in the supplied CD ROM v Operating the Built in Viewer With the built in viewer you can monitor JPEG and MPEG4 images and audio And on VN X235VPU you can perform PTZ operation and configure PTZ related settings x For details please refer to INSTRUCTIONS Setting pdf in the supplied CD ROM Operating Environment Recommended Computer Specifications OS Windows XP Professional or Home Edition SP2 Windows Vista Business SP1 CPU Pentium4 1 5 GHz or higher VN V225VPU Pentium4 2 GHz or higher VN X235VPU 1 GB and above 512 MB or more 1024 x 768 pixels or higher VN V225VPU 1600 x 1200 pixels or higher VN X235VPU True Color 24 bit or 32 bit VRAM 8 MB or more 256 MB and above recommended Internet Explorer XP Version 6 0 Vista Version 7 0 Memory capacity Free hard disk space Display and video card Web browser LAN Environment e 10BASE T 100BASE
15. nection Fill up the piping hole and mounting hole with sealant and insert the silica gel Use sealant GE silicon to fill up the mounting holes x2 to which the piping hole and screws are mounted Note Make sure the holes are completely sealed up Water or moisture may seep in and fog up the lens and dome cover 2 Insert the silica gel provided Note Please make sure that rain does not seep into this unit when mounting on rainy days Be sure to use the silica gel provided Failure to do so may fog up the camera lens and dome cover e If field angle is not adjusted immediately after mounting the camera insert the silica gel provided after adjustment The silica gel provided will lose its effectiveness if it is exposed to the air for a long time VA Space for inserting the silica gel Sealant GE silicon x This illustration is for the purpose of explanation and does not represent the actual camera Adjusting Images When the camera is mounted adjust the image settings while looking at the actual image Before touching the body of the camera make sure to touch the metal surface of the MONITOR terminal to discharge the static electricity from your body The static electricity may cause the camera to malfunction Connect the MONITOR terminal to the test monitor 2 Set the MONITOR OUT selector switch to N or P turn on the power or press and
16. ngs PTZ Settings PTZ Control 2 The Basic Settings1 screen appears Specify the IP Setting HWhen selecting DHCP Disable Select DHCP Disable from IP Setting item of the camera and specify a value in the IP address Subnet Mask and Default Gateway fields When selecting DHCP Enable The default setting is DHCP Disable DHCP client function is off To assign an IP address from the DHCP server connect the camera to a LAN where the DHCP server exists For details on the IP address assigned to the camera consult your network administrator Specify the Time Zone Click OK Copyright 2008 Victor Company of Japan Limited All Rights Reserved Basic Settings1 screen Note Set the DHCP server such that the same IP address is always assigned to the MAC address of the camera by the DHCP server Connection may fail if the above setting is not performed 3 Aconfirmation screen appears e Click OK e The camera restarts using the new IP address It takes about one minute for the camera to restart Memo e Access from this computer may fail when the IP address of the camera is changed To enable access to this unit from the same computer alter the IP address of the computer accordingly When the display or configuration of the opened screen appears strange check the computer settings using the following procedures Click Start Control Panel Disp
17. ork supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 0 100 Subnet mask 255 255 255 0 Default gateway 192 168 0 254 Use the following DNS server addresses Preferred DNS server Altemate DNS server 5 Click OK on the Local Area Connection Properties screen Step2 Internet Explorer settings Launch the Internet Explorer on the computer 2 If proxy settings are enabled in the Internet Explorer follow the steps below to disable the proxy of the Internet Explorer Select in the order of Tool Internet Options Connections LAN Setting followed by deselecting the check for Use a proxy server for your LAN under Proxy Server of the Local Area Network LAN Settings window Local Area Network LAN Settings PR Automatic configuration Automatic configuration may override manual settings To ensure the use of manual settings disable automatic configuration Automatically detect settings Use automatic configuration script Proxy server Use a proxy server for your LAN These settings will not apply to dial up or YPN connections _ ___________ _ Deselect the check v Bypass proxy server For local addresses 3 If the active script of the Internet Explorer is disabled follow the steps b
18. raight cable e Connecting toa computer Use across cable LAN cable to use e STP Recommended shield cable Length of 100 m or shorter e Category 5 and above 4 Connect the power cable Power can be supplied to this unit either by connecting to an AC 24 V power supply or using PoE To use PoE e 3 Connect the LAN cable Note The power supply cable includes cable of the same color as the alarm cable Check properly before connecting e Make sure that power is supplied using only one of the above methods at any one time Connecting simultaneously using the power cable and to PoE via a LAN cable may cause the camera to break down or malfunction e By default the IP addresses of all the cameras are set to 192 168 0 2 If the power of multiple cameras within the same LAN environment are turned on at the same time the IP addresses of the cameras overlap thus preventing proper access As such make sure to turn on the power of the cameras one by one and set the IP addresses such that there is no overlapping E Type of cable Type Color Signal Name Alarm cable Black Red Alarm input 1 shieldad cable Brown Alarm input 2 Orange Alarm output 1 Yellow Alarm output 2 Black GND Audio cable Brown White MIKE IN shielded cable Yellow GND Black White LINE OUT shielded cable Yellow GND Power cable Red unshielded cable AC 24 V Power Supply Black unshielded cable
19. tment ring move the ring to the left and right to adjust the image size After adjusting fasten the screw with pressing it slightly toward the lens direction toward the shooting direction 5 Roughly adjust the focus Lift the focus adjust gear knob and place the catch into B in the diagram Note e The gear is disengaged e f the gear is moved outwards from B the shaft of the gear may shift For details on how to return the gear to the original position refer to es INSTRUCTIONS Installation in the supplied CD ROM Loosen the fastening screw of the focus adjustment ring move it to the left and right to adjust the focus 6 Fine adjust the focus Press the RESET button for more than 2 seconds but less than 5 seconds e The camera enters the focus adjust mode and the STATUS indicator blinks in green and orange alternately e The image is sharpened with the opening of the lens iris e The center of the image is enlarged VN X235VPU only e After adjusting the focus press the RESET button for more than 2 seconds but less than 5 seconds to release the focus adjust mode Shoot the subject Fine adjust the focus e Return the catch to A in the diagram and then rotate the knob to adjust the focus to the optimum position Rotate the focus adjust gear knob about one base pitch in the direction of the arrow in the diagram This is to correct the focus shift when mounting the dome cover
Download Pdf Manuals
Related Search