Philips 42PFL5614 Tv User Guide Manual Operating Instructions Pdf
Contents
1. 7 Connect devices Back connectors for 19 22 inch TV 24 24 Back connectors for 26 inch and larger TV EN 25 Side connectors 27 Connect a computer 28 Use Philips EasyLink 29 Use a Kensington lock 29 Product information 30 Supported display resolutions 30 Multimedia 30 Tuner Reception Transmission 30 Remote control 30 Power 30 Supported TV mounts 30 Troubleshooting 32 General TV issues 32 TV channel issues 32 Picture issues 32 Sound issues 33 HDMI connection issues 33 Computer connection issues 33 Contact us 33 10 Index 34 English 1 Notice 2009 Koninklijke Philips Electronics N V All rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied Warranty e Risk of injury damage to TV or void of warranty Never attempt to repair the T V yourself e Use the TV and accessories onl2. EN 19 English Access decoder channel You can map channels provided through a decoder or descrambler to your TV channel selection In this way you can select these channels by using the RC of your TV The decoder or a descrambler must be connected to EXT1 Set decoder channel Map channels from a decoder or descrambler Press amp Home Select Setup gt Installation gt Decoder Press to enter Decoder Press to enter Channel Press AY to select channel number to map to the decoder descrambler channel Press OK Press AY 4b to select and enter Status COND URW N gt Press AV to select the connector used by the decoder descrambler None or EXT 1 Press OK O Press Home to exit 0 Note Select None if you do not want to map to the decoder descrambler channel Start a TV demo 1 Press DEMO on the remote control 2 Press AV to select a demo and press OK to view it 3 Press DEMO to exit 20 EN Downloaded From TV Manual com Manuals Reset the TV to factory settings You can restore the default picture and sound settings of your T V Channel installation settings remain the same 1 Pest Home 2 Select Setup gt Installation gt Factory settings 3 Press OK or to enter the Factory settings menu L gt Reset is highlighted Press OK to reset to factory settings Un A Press amp Home to exit
3. TV lock child lock lock channels 16 lock connected devices 16 PIN code 15 U USB listen to music 19 view photos 18 V Video format video format technical specifications 30 volume adjust 9 W Wallpaper 16 EN 35 English Information about how to re tune your TV during the TV switchover Keep this user manual safe you ll need it e nmu Television in the UK is going digital bringing us all more choice and new services Starting in late 2007 and ending in 2012 television services in the UK will go completely digital TV region by TV region Please see the next page to find out when your area switches to digital Digital UK is the independent non profit organisation leading the process of digital TV switchover in the UK Digital UK provides im partial information on what people need to do to prepare for the move to digital and when they need to do it 36 EN Downloaded From TV Manual com Manuals How the switchover affects your TV equipment Your new TV has a digital tuner built in which means it is ready to receive the Freeview signal by simply plugging it into your aerial socket check if you can get digital TV through your aerial now or whether you ll have to wait until switchover at www digitaluk co uk When the TV switchover happens in your area there are at least two occasions when you will need to re tune your TV in order to continue receiving your existing TV channels and also t
4. Installation gt Channel install gt Analogue Manual L gt The Analogue Manual menu appears Press AY 4b to select and enter System Press AY to select your country or region Press OK to confirm Press Home to exit DU AW Step 2 Search and store new TV channels 1 Press Home 2 Press Av to select Setup gt Installation gt Channel install gt Analogue Manual L gt The Analogue Manual menu appears Press AYA to select and enter Search A WwW Press AY or use Numeric buttons to manually enter the three digit frequency 5 Press OK to begin search L f a channel is unavailable at the selected frequency the system searches for the next available channel 6 Press BACK when the new channel is found 7 Press AV to select Store new channel o store the new channel under a new channel number 8 Press to enter Store new channel 9 Press lt P to select Yes and press OK to store the new channel 10 Press amp Home to exit Step 3 Fine tune analogue channels 1 Press Home 2 Press ava to select Setup gt Installation gt Channel install gt Analogue Manual L gt The Analogue Manual menu appears Press AY 4b to select and enter Fine tune Press AY to adjust frequency Press OK when done Press AY to select Store cur chan to store channel number Press P to enter Store cur chan Press lt P to select Yes
5. TV Manual com Manuals English PHILIPS 13 5C Q41G42018 2009 Koninklijke Philips Electronics N V All rights reserved i Document order number Q41G4201813 5C ae m Downloaded From TV Manual com Manuals
6. TV speakers on or off Setting TV speakers to automatic mode turns off the speakers when content from an EasyLink compliant home theatre system is detected Surround Enables spatial sound Headphone volume Adjusts headphone volume e Auto volume Automatically reduces sudden volume changes for example when switching channels When enabled this produces a more consistent audio volume Delta volume Levels out volume differences between channels or connected devices Switch to the connected device before you change the delta volume Use advanced teletext features Access the teletext options menu Most of the advanced teletext features are accessed via the teletext options menu 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press OPTIONS L gt The teletext options menu appears 3 Press AV to select one of the following options e Freeze Page Freezes the current page e Dual Full screen Enables and disables dual screen teletext which splits the current channel or source to the left of the screen with teletext on the right e Reveal Hides or reveals hidden information on a page such as solutions to riddles or puzzles e Cycle subpage Cycles through subpages automatically if subpages are available Downloaded From TV Manual com Manuals e Language Switches to a different language group to display a language correctly when that language uses a different
7. and press OK to store current channel o ON DURA W Press ft Home to exit Step 4 Skip channels 1 Pest Home 2 Press Av to select Setup gt Installation gt Channel install gt Analogue Manual L gt The Analogue Manual menu appears 3 Press AY4 to select and enter Skip channel 4 Press lt P to select Yes and press OK to skip current channel L gt The selected channel is skipped when you press P on your remote control or view the channel grid 5 Press amp Home to exit Note You can restore a skipped channel to your channel listing see Step 2 Search and store new TV channels on page 22 Rename channels Channels can be renamed so that a name of your choice appears whenever the channel is selected 1 when watching TV press OK to display the channel grid 2 Select the channel you want to rename Downloaded From TV Manual com Manuals 3 Press OPTIONS L gt The channel options menu appears 4 Press AVP to select and enter Rename chan L gt A text input box appears Press AVP to select characters ON UI Press OK to confirm each of the characters Tip Rename channels the length of the name is limited to six characters Use Aa to change upper case letter to lower case letter and vice versa Rearrange channels After you install channels you can rearrange the order in which they appear 1 when wat
8. character set Press OK to confirm your choice Press MHEG TELETEXT to exit the teletext options menu Un A Select teletext subpages A teletext page can hold several subpages Subpages are displayed on a bar next to the main page number 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Select a teletext page with subpages 3 Press to entera subpage L gt The subpage appears 4 Press lt gt to switch between subpages Select T O P teletext broadcasts Table Of Pages T O P teletext broadcasts allow you to jump from one subject to another without using page numbers T O P teletext is not broadcast on all TV channels 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press INFO L gt The T O P overview appears J Press Av to select a subject 4 Press OK to view the page Create and use lists of favourite channels You can create lists of your preferred TV channels and radio stations so that you can find those channels easily EN 13 English Tip You can create and store up to four favourite lists on your TV Select a favourite list 1 when watching TV press OK to display he channel grid 2 Press OPTIONS L gt The channel options menu appears J Press OK to select Show favourite ch L gt The favourite lists appear 4 Press AY to select a favourite list 5 Press OK Only channels in the favourite lis
9. source EN 29 Downloaded From TV Manual com Manuals English 8 Product information Product information is subject to change without notice For detailed product information go to www philips com support Supported display resolutions Computer formats e Resolution refresh rate 640 x 480 60Hz 800 x 600 60Hz e 1024 x 768 60Hz e 1280 x 1024 60 Hz e 1360 x 768 60Hz e 1440 x 900 60Hz e 1680 x 1050 60Hz e Via HDMI DVI input Video formats e Resolution refresh rate e 480i 60Hz 480p 60Hz e 576i 50Hz e 576p 50Hz e 720p 50Hz 60Hz e 1080i 50Hz 60Hz e 1080p 24Hz 25Hz 30Hz 50Hz 60Hz Multimedia e Supported storage device USB Only FAT or FAT 32 USB storage devices are supported e Supported multimedia file formats Images JPEG e Audio MP3 30 EN Downloaded From TV Manual com Manuals Note Multimedia file names must not exceed 32 characters Tuner Reception Transmission e Aerial input 5ohm coaxial IEC75 e TV system PAL B G D K SECAM B G D K L L Video playback NTSC SECAM PAL e Tuner Bands Hyperband S channel UHF VHF Remote control e Type PFO2E09B PFO2E09BW 22PFL5614 60 e Batteries 2 x AAA LRO3 type Power Mains power 220 240V 50Hz Standby power lt 0 15W e Ambient temperature 5 to 40 degrees Celsius Supp
10. teletext source on the TV Use the source button Een 1 Press MHEG TELETEXT L gt The main index page appears 2 Select a page as follows 1 Press SOURCE e Press the Numeric buttons to enter L gt The source list appears a page number 2 e Press P or AY to view the next Press the Navigation buttons to select a PAK or previous page e Press the Colour buttons to select a J Press OK to confirm your choice colour coded item L gt The TV switches to the selected Press BACK to return to a device previously viewed page J Press MHEG TELETEXT to exit teletext EN 9 Downloaded From TV Manual com Manuals 5 Use more of your product Access TV menus Menus help you to install channels change picture and sound settings and access other features 1 Presa Home L gt The menu screen appears 3 ich TV q Add new device Setup _J 2 Press the AVP to select and navigate through one of the following menus e Watch TV Switches back to the aerial source if another source is selected Setup Accesses menus that allow you to change picture sound and other TV settings e Add new device Adds new devices to the home menu Press OK to confirm your choice Press amp Home to exit A w Tip After selecting Add new device follow the on screen instructions to select the correct device and connector Downloaded From
11. to develop produce and market products that cause no adverse health effects Philips confirms hat if its products are handled properly for their intended use they are safe o use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips o anticipate further developments in standardisation for early integration in its products Mains fuse UK only This TV is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 104A Remove fuse cover and fuse The replacement fuse must comply with BS 1362 and have the ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type Refit the fuse cover In order to maintain conformity to the EMC directive the ma not be detached Copyright VESA FDMI and ins plug on this product must from the mains cord cable the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association 9 Kensington and Micro Saver are registered US trademarks of ACCO World Corporation with issued regis applications in o world rations and pending her countries throughout the All other registered and unregistered trademarks are owners he property of their respective Downlo
12. 24 technical specifications 30 troubleshooting 33 connectors overview 24 D demo 20 devices add to home menu 10 connect 24 watch 9 display resolution 30 Dual view 17 34 EN Downloaded From TV Manual com Manuals E EasyLink disable 29 enable 29 one touch play 29 one touch standby 29 environmental care 5 F factory settings 20 favourite list select 14 set up 13 H HDMI cable troubleshooting 33 install channels automatic 21 manual 22 K Kensington lock 29 L location 19 lock Kensington 29 TV lock child lock 15 M menu main menu 10 teletext 13 Multimedia technical specifications 30 music USB 19 O One touch play 29 One touch standby 29 P PC pc connection 28 picture format picture format change 11 troubleshooting 32 Picture settings 10 PIN code 15 R reception 32 remote control overview 6 technical specifications 30 S settings sound 12 settings assistant 10 Smart settings 10 12 software version 19 sound settings 12 T Table of Pages 13 technical specifcations 30 Teletext features 15 subpages 13 table of pages 13 timer on timer 15 Sleep timer 15 standby 15 troubleshooting 32 TV adjust volume 9 as PC monitor 28 menu 10 Downloaded From TV Manual com Manuals pc connection 28 preferences 19 screen care 5 software 19 standby 8 switch channels 8 switch off 8 switch on 8 troubleshooting 32 tuner technical specifications 30 wall mount 30
13. 6 Install channels The first time you set up your TV you are prompted to select a menu language and to install TV and digital radio channels if available This chapter provides instructions on how to re install and fine tune channels Automatically install channels This section describes how to search and store channels automatically Step 1 Select your menu language Note Skip this step if your language settings are correct Press amp Home Press AY 4b to select Setup gt Installation gt Language gt Menu language NA Press to enter Menu language 4 Press AY to selecta language setting and hen OK to confirm Picture English Channel install Cesky id Sound Preferences Benrapcku Decoder Dansk in Features 7 Factory setting Deutsch lt ien Current software EAAnvik Ss Espa ol D Software update Fran ais 5 Press amp Home to exit Downloaded From TV Manual com Manuals Step 2 Install Channels Select your country for proper channel installation 1 Press Home 2 Press Av to select Setup gt Installation gt Channel install gt Channel assistant Picture iq Sound m o Features le 3 Installation t Software update Menu language Channel assistant Analogue Manual Preferences Decoder Factory setting Current software 3 Press AV to select your country and then gt to go to th
14. AW Na Press Done to confirm Downloaded From TV Manual com Manuals 8 Press Av to select Programme no and set the channel 9 Press OK to confirm 10 Press amp Home to exit Tip Select On timer gt Activate gt Off to disable On timer When On timer is Off only Activate can be selected Set the TV clock before activating On timer feature Use TV lock You can prevent your children from watching certain programs or certain channels by locking the TV controls Set or change the TV lock code Press f Home Press AY 4b to select Setup gt Features gt Set code Press gt to enter the code setup Enter your code using the Numeric buttons UI AW Na Re enter the same code in the new dialogue box for confirmation L gt If the code is set successfully the dialogue box will disappear However if the code cannot be set a new dialogue box will prompt you to re enter the code 6 If you want to change the code select Y g Setup gt Features gt Change code 7 Enter your current code using the Numeric buttons L gt If the code is validated a new dialogue box will prompt you to enter your new code EN 15 English 8 Enter the new code using the Numeric buttons tL A message appears prompting you to enter the new code again for confirmation Tip f you forget your code enter 8888 to override any existing co
15. K to view the selected photo in full screen mode Tip When in full screen mode press to move between photos View a slide show of your photos 1 When a full screen image of a photo is displayed press OK or PIL L gt A slide show begins from the selected image 2 Press e OK or PII to pause the slide show L gt Thell icon appears e Press or gt gt to move between images e Press BACK or to stop the slide show Change slide show settings 1 when viewing a slide show press OPTIONS t The slide show options menu appears 2 Press AV to select one of the following e Start Stop slide Starts or stops a slide show e Slideshow trans Sets the transition from one picture to the next Slideshow freq Sets the amount of time that a picture is shown e Rotate image Rotates a picture e Show info Displays the picture name date size and next picture in the slide show J Press OK to confirm your setting Note Rotate image and Show info appear only when you press OK or FI to pause the slideshow Listen to music 1 n the USB thumbnail browser view select MUSIC and press gt to enter 2 Press GUIDE to switch between humbnail and file browsing views 3 Press AY 4b to select music or a music album 4 Press OK to play the selected music Music settings When listening to music press OPTIONS to access one ofthe following music se
16. Register your product and get support at www philips com welcome L5404 60 L5604 60 L5614 60 L5404 60 L5604 60 L5614 60 L5604 60 L5614 60 UU U UU U U U EN User Manual RU PykoBoAcrBO noAb3oBaTeAs PHILIPS Downloaded From TV Manual com Manuals Model Serial sterreich Belgi Belgique Bparapna Hrvatska Ceska republika Danmark Estonia Suomi France Deutschland E Aa a Magyarorsz g Ireland Italia KasakcraH Latvia Lithuania Luxemburg Luxembourg Nederland Norge Polska Portugal Rom nia Poccua Cp6uja Slovensko Slovenija Espana Sverige Suisse Schweiz Svizzera Turkiye United Kingdom Ykpa na Downloaded From TV Manual com Manuals 0810 000205 078250145 3592 489 99 96 01 6403 776 800142840 3525 8759 6008600 09 2311 3415 0821 611655 01803 386 852 0 0800 3122 1280 0680018189 North 0800 055 6882 South 1800 PHILIPS 7445477 840320086 7 727 250 66 17 67228896 52737691 40 6661 5644 0900 8407 2270 8111 022 3491504 800 780 903 031 810 71 25 0800 89 49 10 Moscow 495 961 1111 Outside Moscow 8 800 200 0880 381 114 440 841 0800 004537 00386 12 80 95 00 902 888 784 08 5792 9100 0844 800 544 0800 261 3302 General No 0870 900 9070 General National Rate No 0870 911 0036 8 800 500 69 70 0 07 pro Minute 0 06 Per minuut Par minute Mecren pasroBop Lokalni poziv Bezplatny hovor Lokalt opkald local paika
17. TV Manual com Manuals Remove devices from the home menu If a device is no longer connected to the TV remove it from the home menu 1 Press Home 2 Press AVP to select a device to remove 3 Press OPTIONS L gt The Remove device list appears 4 Press OK and select Remove to remove he device L gt The selected device is removed from the home menu Change picture and sound settings Change picture and sound settings to suit your preferences You can apply pre defined settings or change settings manually Use settings assistant Use the settings assistant to guide you through the best picture and sound settings 1 Pest Home 2 Press ava to select Setup gt Picture gt Settings assistant 3 Press OK L gt The Settings assistant menu appears Follow the on screen instructions to choose your preferred picture settings Use smart picture Use smart picture to apply pre defined picture settings 1 Press O PICTURE L gt The Smart picture menu appears 2 Press AV to select one of the following smart picture settings 3 e Personal Lists customised personal picture settings Vivid Maximises picture settings Standard Adjusts picture settings to suit most environments and types of video e Movie Applies picture settings ideally suited for movie viewing Game Applies picture settings maximised for fast moving games Energy saving Applies low energy pi
18. aded From TV Manual com Manuals EN English 2 Important Read and understand all instructions before you use your TV If damage is caused by failure to follow instructions the warranty does not apply Safety e Risk of electric shock or fire Never expose the TV to rain or water Never place liquid containers such as vases near the T V If liquids are spilt on or into the TV disconnect the TV from the power outlet immediately Contact Philips Consumer Care to have the TV checked before use Never place the TV remote control or batteries near naked flames or other heat sources including direct sunlight To prevent the spread of fire keep candles or other flames away from the TV remote control and batteries at all times ever insert objects into the ventilation slots or other openings on he TV When the TV is swivelled ensure hat no strain is exerted on the power cord Strain on the power cord can loosen connections and cause arcing Risk of short circuit or fire ever expose the remote control or batteries to rain water or excessive heat Avoid force coming onto power plugs Loose power plugs can cause arcing or fire e Risk of injury or damage to the TV Downloaded From TV Manual com Manuals Two people are required to lift and carry a T V that weighs more than 25 kg When stand mounting the TV use only the supplied stand Secure the stand to the TV tightly Place the TV on a f
19. ching TV press OK to display the channel grid 2 Press OPTIONS L gt The channel options menu appears Press AY 4b to select and enter Reorder Select the channel you want to reorder and press OK Press AY 4b to select the new position for the channel Press OK to confirm the new position Press amp OPTIONS L gt Done reordering appears OO NOA U A UJ Press OK to finish reordering EN 23 English 7 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start Note Different types of connectors may be used to connect a device to your TV depending on availability and your needs Back connectors for 19 22 inch TV TV ANTENNA SPDIF OUT 00000 L m 24 EN Downloaded From TV Manual com Manuals n PC IN VGA and AUDIO IN Audio and video input from a computer PC IN AUDIO 2 HDMI 1 Digital audio and video input from high definition digital devices such as Blu ray players HDMI I 3 SERV U For use by service personnel only SPDIF OUT Digital audio output to home theatres and other digital audio systems 5 TV ANTENNA Signal input from an antenna cable or satellite 750 r TV ANTENNA AV OUT VIDEO OUT and AUDIO OUT L R Audio and video output to ana
20. cture settings Press OK to confirm your choice L gt The selected smart picture setting is applied Manually adjust picture settings 1 2 Press ft Home Press AY 4b to select Setup gt Picture L gt The Picture menu appears Press AY 4b to select one of the following picture settings Smart picture Accesses pre defined smart picture settings Contrast Adjusts the intensity of bright areas keeping dark areas unchanged Brightness Adjusts the intensity and details of dark areas Colour Adjusts colour saturation Hue Compensates colour variations in NTSC encoded transmissions Sharpness Adjusts the level of sharpness in image details Noise reduction Filters and reduces noise in an image Tint Adjusts the colour balance in an image Custom tint Make a customised tint setting Pixel Plus HD Digitally adjusts picture quality to optimal contrast colour and sharpness Downloaded From TV Manual com Manuals e Dynamic contrast Automatically enhances contrast in an image A Medium setting is recommended e Dynamic backlight Adjusts the brightness of the TV backlight to match lighting conditions Colour enhancement Makes colours more vivid and improves the resolution of details in bright colours You can switch this feature on or off e Light sensor Dynamically adjusts picture settings to match lighting conditions PC mode Adjusts the picture when a PC is connec
21. d Scenea picture is removed from the TV Repeat these instructions to personalise the Scenea picture again Display a slideshow of pictures with Scenea 1 While the TV is on connect the USB storage device containing your pictures JPEG format only to the USB connector at the side of your T V L gt The home menu appears 2 Press SCENEA L gt All pictures in your USB storage device are displayed in a slideshow starting from the default Scenea picture stored in your TV Downloaded From TV Manual com Manuals Use sleeptimer with Scenea wallpaper By default your TV displays the Scenea picture or slideshow for 120 minutes before entering standby mode If sleeptimer is enabled the Scenea picture or slideshow is displayed for the duration of the sleeptimer see Use timers on page 15 Use Eco mode with Scenea wallpaper Using Eco mode with Scenea saves energy by lowering the TV brightness when a Scenea picture or a slideshow is displayed 1 while a Scenea picture or slideshow is displayed press C PICTURE L gt The Eco mode menu appears Press lt P to select On Press OK L gt Eco mode with Scenea is enabled WN Watch TV in dual view You can use the Dual View feature to display the TV channels and the input from a device with VGA or DVI connector such as a computer or a satellite box simultaneously on your TV 1 Pest Home 2 Press Av to select Setup gt Features gt Dua
22. des Lock or unlock the TV Locking the TV prevents your child from accessing all channels and connected devices 1 Pest Home 2 Press Av to select Setup gt Features gt TV lock 3 Press to enter the TV lock L gt A screen appears prompting you to enter a code Enter your code using Numeric buttons Press AV to select Lock or Unlock Press OK L gt All channels and connected devices are locked or unlocked Ov Ui A 7 Press amp Home to exit Note f you select Lock you have to enter your code every time you turn on your T V Lock or unlock one or more channels When watching TV press OK to display the channel grid N Press AV to select a channel to lock or unlock Press OPTIONS Press AV to select Lock channel or Unlock channel A LW 16 EN Downloaded From TV Manual com Manuals 5 For each selection press OK to lock or unlock the channel Note Restart the TV for the change to take effect Use the TV clock You can display a clock on the TV screen Set the TV clock 1 Pest Home 2 Select Setup gt Features gt Clock L gt The Clock menu appears 3 Press Av 4 or Numeric buttons to enter time Press Done to confirm Press t Home to exit Un A Use Scenea Scenea transforms your TV into a personalised photo frame With Scenea enabled you can display a single picture or a slides
23. e next step Belgium Croatia Czech Republic 4 Denmark Finland France Germany v 4 Select Start and press OK to re install channels Start automatic installation This takes a few minutes L gt As the system searches for channels you have the option to Stop the process 5 To stop searching select Stop and press OK L gt A dialogue box appears asking you if you really want to Stop or Continue with the process EN 21 English 6 Press lt gt to select Stop or Continue 7 Press OK to confirm your choice 8 When done press Home to exit Manually install channels This section describes how to search and store analogue TV channels manually 1 Pest Home 2 Press AVP to select Setup gt Installation gt Channel install gt Analogue Manual L gt The Analogue Manual menu appears Menu language Picture Analogue Manual Iq Sound Preferences Channel assistant Decoder a oO Features ot Installation D Software update 3 Press AV to select the item you want to Factory setting Current software adjust _ System e Search Fine tune e Store cur chan Store new channel e Skip channel Step 1 Select your system Note Skip this step if your system settings are correct 1 Pest Home 22 EN Downloaded From TV Manual com Manuals Press AY 4b to select Setup gt
24. el is poor fine tune this channel There is poor picture quality from connected devices Check that the devices are connected properly e Check that the picture settings are correctly set The TV did not save your picture settings e Check that the TV location is set to the home setting This mode offers you the flexibility to change and save settings The picture does not fit the screen it is too big or too small e Try using a different picture format The picture position is incorrect Picture signals from some devices may not fit the screen correctly Check the signal output of the device Sound issues There is a picture but sound quality is poor Note f no audio signal is detected the TV automatically switches the audio output off this does not indicate malfunction e Check that all cables are properly connected Check that the volume is not set to 0 e Check that the sound is not muted There is a picture but the sound quality is poor e Check that the sound settings are correctly set There is a picture but sound comes from one speaker only e Verify that sound balance is set to the centre HDMI connection issues There are problems with HDMI devices Note that HDCP support can delay the time taken for a TV to display content from a HDMI device Ifthe TV does not recognize the HDMI device and no picture is displayed try switching t
25. he source from one device to another and back again fthere are intermittent sound disruptions check that output settings from the HDMI device are correct Downloaded From TV Manual com Manuals Ifa HDMI to DVI adaptor or HDMI to DVI cable is used check that an additional audio cable is connected to AUDIO L R or AUDIO IN mini jack only Computer connection issues The computer display on the TV is not stable e Check that a supported resolution and refresh rate is selected on the computer Set the TV picture format to unscaled Contact us f you cannot resolve your problem refer to he FAQs for this product at www philips com support f the problem remains unresolved contact Philips Consumer Care in your country as isted in the Addendum VN Warning Do not attempt to repair the product yourself This may cause severe injury irreparable damage to your product or void your warranty Make a note of your TV model and serial number before you contact Philips These numbers are printed on the back of the TV and on the packaging EN 33 English 10 Index A analogue channel fine tune 22 B bracket 30 C Channel list favourite 13 troubleshooting 32 Channels favourite list 13 install automatic 21 manual 22 rename 23 reorder 23 Clock 16 computer format technical specifications 30 Connections HDM troubleshooting 33 mains cord 24 overview
26. how of pictures on your TV perfect for parties or other social gatherings Note Use Eco mode to save energy when the Scenea wallpaper or a slideshow is displayed on your TV see Use Eco mode with Scenea wallpaper on page 17 Scenea wallpaper is not available in shop mode see Change TV preferences on page 19 or MHEG mode UK only Display a single picture with Scenea 1 while watching TV press SCENEA L gt The default Scenea picture is displayed on your TV 2 Press any key except Standby On or C PICTURE to return to normal TV viewing 3 Pres any key except Standby On or CJ PICTURE to return to normal TV viewing Personalize the Scenea picture 1 While the TV is on connect the USB storage device containing your pictures JPEG format only to the USB connector at the side of your T V L gt The home menu appears If the home menu does not appear press ff Home 2 select Browse USB then press OK L gt The USB content browser appears 3 Press Av to navigate to the picture of your choice 4 Press SCENEA L Your picture is stored as the default Scenea picture in your T V D Disconnect the USB storage device The device can be disconnected safely while he TV is on Follow the instructions to display your personalised Scenea picture see Display a single picture with Scenea on page 16 Note fthe TV is reset to factory settings your personalise
27. l View J Press OK to activate Dual View L gt The main screen displays the input source from DVI or VGA L gt The auxiliary screen displays the last viewed TV channel 4 Pres amp Home to exit dual view EN 17 English Note Dual View is available only when the TV is connected to a device such as a PC via VGA or DVI connection When in Dual view mode press 41 to adjust volume in the main screen and press P or Numeric buttons to switch between the TV channels in the auxiliary screen View photos and play music from a USB storage device Caution Philips is not responsible if the USB storage device is not supported nor is it responsible for damage or loss of data from the device Your TV is fitted with a USB connector that enables you to view photos or listen to music stored on a USB storage device 1 Tumonthe TV 2 Connect the USB device to the USB port on the side of your TV L gt The home menu appears 3 Press Av to select Browse USB 4 Press OK to confirm L gt The USB thumbnail browser appears Tip Press GUIDE to switch between thumbnail and file browsing views Downloaded From TV Manual com Manuals View photos 1 n the USB content browser select Picture and press gt to enter Press GUIDE to switch between humbnail and file browsing views Press AY 4b to select a photo or a photo album A OW N Press O
28. lat level surface that can support the combined weight of the TV and the stand When wall mounting the TV use only a wall mount that can support the weight of the TV Secure the wall mount to a wall that can support the combined weight of the TV and wall mount Koninklijke Philips Electronics V bears no responsibility for improper wall mounting that result in accident injury or damage Risk of injury to children Follow these precautions to prevent the TV from toppling over and causing injury to children ever place the TV on a surface covered by a doth or other material hat can be pulled away Ensure that no part of the T V hangs over the edge of the surface ever place the TV on tall furniture such as a bookcase without anchoring both the furniture and TV o the wall or a suitable support Educate children about the dangers of climbing on furniture to reach the TV Risk of overheating Never install the TV in a confined space Always leave a space of at least 4 inches or 10 cm around the TV for ventilation Ensure curtains or other objects never cover the ventilation slots on the TV Risk of damage to the TV Before yo connect the TV to the power outlet ensure that the power voltage matches he value printed on the back of the T V ever connect the TV to the power outlet if the voltage is different Risk of injury fire or power cord damage ever place the TV or any objects on the power cord To easi
29. llispuhelu 0 09 Par minute 0 09 pro Minute KNien xwpis xp won Ingyenes h v s free 0 08 Al minuto local local local Ortsgespr ch Appel local 0 10 Per minuut Lokalsamtale potaczenie lokalne Chamada local Apel local MectHbiii 3BOHOK Lokalni poziv Bezplatny hovor lokalni klic 0 10 Por minuto Lokalsamtal Appel local Ortsgespr ch Chiamata locale Sehirici arama local Micuesun BAKAMK This information is correct at the time of press For updated information see www philips com support Contents 1 Notice 2 2 Important 4 3 TV overview 6 Side controls and indicators 6 Remote control 6 4 Use your product 8 Switch your TV on off or to standby 8 Switch channels 8 Watch connected devices 9 Adjust TV volume 9 Use teletext 9 5 Use more of your product 10 Access TV menus 10 Remove devices from the home menu 10 Change picture and sound settings 10 Use advanced teletext features 13 Create and use lists of favourite channels 13 Use timers 15 Use TV lock 15 Use the TV clock 16 Use Scenea 16 Watch TV in dual view 17 View photos and play music from a USB storage device 18 Update the TV software 19 Change TV preferences 19 Access decoder channel 20 Start a I V demo 20 Reset the TV to factory settings 20 6 Install channels 21 Automatically install channels 21 Manually install channels 22 Rename channels 23 Rearrange channels 23 Downloaded From TV Manual com Manuals
30. logue devices such as another TV or a recording device EXT 2 Y Pb Pr and AUDIO L R Analogue audio and video input from analogue or digital devices such as DVD players or game consoles D EXT 1 RGB and CVBS Analogue audio and video input from analogue or digital devices such as DVD players or game consoles EXT RGB CVBS LI a m m m m LI C m m m L1 m m m LI m OO COOL Downloaded From TV Manual com Manuals Back connectors for 26 inch and larger TV a HDMI 1 m e TV RUM Y WM CD LEFT RIGHT J How 11 ov 4 TT rene aaa EN 25 English 4 PC IN VGA and AUDIO IN SPDIF OUT Audio and video input from a computer Digital audio output to home theatres and other digital audio systems PC IN AUDIO A G EXT 1 RGB and CVBS CVBS EXT 2 Analogue audio and video input from A analogue or digital devices such as DVD players or game consoles EXT 2 supports 2 HDMI 1 2 idis Digital audio and video input from high Ra definition digital devices such as Blu ray RGB CVBS CVBS DVD players HDMI I HDMI 2 OO ODO OOOO DOOD Bluray Disc ODO OO OO 3 TV ANTENNA Signal input from an antenna cable or EXT 3 Y Pb Pr and AUDIO L R satellite Analog
31. ly disconnect the TV power cord c from the power outlet ensure that you have full access to the power cord at all imes When you disconnect the power cord always pull the plug never the cable e Disconnect the TV from the power outlet and aerial before lightning storms During ightning storms never touch any part of he TV power cord or aerial cable e Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time e Ifthe TV is transported in temperatures below 5 C unpack the T V and wait until the TV temperature matches room emperature before connecting the TV to he power outlet Screen care e Avod stationary images as much as possible Stationary images are images that remain on screen for extended periods of time Examples include on screen menus black bars and time displays If you must use stationary images reduce screen contrast and brightness to avoid screen damage Unplug the TV before cleaning e Clean the TV and frame with a soft damp cloth Never use substances such as alcohol chemicals or household cleaners onthe TV e Risk of damage to the TV screen Never touch push rub or strike the screen with any object e To avoid deformations and colour fading wipe off water drops as soon as possible Disposal of your old product and batteries s Your product is designed and manufactured with high quality ma
32. ncreases or decreases volume 4o 5x Tears 8w PHILIPS TELEVISION 6 EN Downloaded From TV Manual com Manuals Standby On e Switches the TV to standby if it is on e Switches on the TV if it is in standby MHEG TELETEXT Toggles teletext on or off SOURCE Selects connected devices Colour buttons Selects tasks or options AD Audio Descriptor For RF Digital TV only UK only Enables audio commentary for the visually handicapped f Home Toggles the home menu on or off OPTIONS Accesses options relating to the current activity or selection OK Confirms an entry or selection and displays the channel grid when watching TV Av Navigation buttons Navigates through the menus INFO Displays program information when available If the information spans multiple pages press OPTIONS to go to the next page 4 Backward Searches backward gt gt Forward Searches forward gt Il Play Pause Starts pauses or resumes playback Record only used for Easylink features Starts or stops video recording W Stop Stops playback Downloaded From TV Manual com Manuals D sk Mute Mutes or restores audio output P Programme Switches to the next or previous channel When the TV menu is on this functi
33. o pick up new ones get set for digital V Digital UK the body leading the digital TV How to re tune switchover will advise you when you need to re tune during the switchover To find out how to re tune your TV check If you choose to connect your TV to satellite or this user manual for details cable with a digital box then it will not be Go to section 6 Install channels affected by switchover and you won t need to re tune If you do not re tune your channels when advised to do so by Digital UK you may lose If you have any questions please contact your some or all of your channels until you do equipment supplier or call Digital UK on re tune You should re tune your TV every 0845 6 50 50 50 or visit www digitaluk co uk few months to check for any new channels If you are missing any channels it may be that they are not available in your area or that your aerial needs upgrading When does switchover happen Copeland switches on October 17 2007 B pj Ne d d sf Shetland Islands a tS STV North sl v 2010 4 gt P 5 STV Central 2010 11 2008 og Tyne Tees 2012 Yorkshire 2011 Central Anglia Wales zo Visit us at digitaluk co uk Call us on 0845 6 50 50 50 2009 10 London 2012 Meridian 2012 West Country v t Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends Rates may vary for calls from non BT lines EN 37 Downloaded From
34. ons as Page Up Down amp 3 FORMAT Selects a picture format 0 9 Numeric buttons Selects a channel or setting PICTURE Launches the picture menu Not supported on all models SOUND Launches the sound menu Not supported on all models 1 Volume ncreases or decreases volume BACKP P Previous channel Returns to a previous channel or menu screen GUIDE Switches between channel grid and programme list SCENEA Wallpaper Displays wallpaper on your TV screen DEMO Toggles the demonstration menu on or off TV Switches back to the aerial source SUBTITLE For RF Digital TV only Enables or disables subtitles EN English 4 Use your Note d t f you cannot locate your remote control and p ro u C want to switch on the TV from standby press P CH or SOURCE at the side of the TV This section helps you perform basic operations see Use more of your product on page 10 Switch channels Switch your TV on off or to standby lunc Lose 4 To switch on e fthe standby indicator is off press Bl P 5 POWER POWER at the side of the T V e Ifthe standby indicator is red press e Press P on the remote control or Standby On on the remote control P CH on the side of the TV To switch to standby e Enter a channel number using the e Pre
35. orted TV mounts To mount the TV purchase a Philips IV mount or a VESA compatible TV mount To prevent damage to cables and connectors be sure to leave a clearance of at least 2 2 inches or 5 5cm from the back of the TV Warning Follow all instructions provided with the TV mount Koninklijke Philips Electronics N V bears no responsibility for improper TV mounting that results in accident injury or damage TV screen Required Required size inches pitch mm mounting bolts 19 75 x 75 4x M4 22 100 x 100 4 x M4 26 200 x 100 6 x M4 32 200x200 4xM6 42 400 x 400 4xM6 Downloaded From TV Manual com Manuals EN 31 English 9 Troubleshooting This section describes commonly encountered issues and accompanying solutions General TV issues The TV does not switch on Disconnect the power cable from the power outlet Wait for one minute then reconnect it e Check that the power cable is securely connected The remote control is not working properly Check that the remote control batteries are correctly inserted according to the orientation Replace the remote control batteries if hey are flat or weak Clean the remote control and TV sensor ens The standby light on the TV blinks red e Disconnect the power cable from the power outlet Wait until the T V cools down before reconnecting the power cable If the blinking reoccurs contact Philips Cons
36. ou connect a computer to the TV HDMI ly HDMI 2 Set the screen refresh rate on your computer to 60Hz e Select a supported screen resolution on your computer Connect a computer with one of the following connectors Note Connections via DVI or VGA require an additional audio cable Downloaded From TV Manual com Manuals e VGA cable Use one touch standby For TV of size 22 inch and smaller 1 Press and hold OStandby on the TV s or For TV of size 26 inch and larger NC AUDIO in i device s remote control for at least three een seconds HDMI 2 DVI von YN L gt The TV and all connected HDMI devices switch to standby Use a Kensington lock There is a Kensington security slot at the back of the TV Prevent theft by looping a Kensington ock between the slot and a permanent object such as a heavy table Use Philips EasyLink Your TV supports Philips EasyLink which enables one touch play and one touch standby between EasyLink compliant devices Note Compliant devices must be connected to your TV via HDMI Enable or disable EasyLink Note Do not enable Philips EasyLink if you do not intend to use it 1 Press MENU 2 select Installation gt Preferences gt EasyLink J Select On or Off Use one touch play 1 After enabling EasyLink press play on your device L gt The TV automatically switches to the correct
37. solution under 1024 x 768 only Allows maximum sharpness Some distortion may be present due to the broadcaster s systems Set your PC resolution to wide screen mode for best results 12 EN Downloaded From TV Manual com Manuals Use smart sound Use smart sound to apply pre defined sound settings 1 Press SOUND L gt The Smart sound menu appears 2 Press AV to select one of the following smart sound settings e Standard Adjusts sound settings to suit most environments and types of audio e News Applies sound settings ideally suited for spoken audio such as the news e Movie Applies sound settings ideally suited for movies e Personal Applies the settings that were customised in the sound menu J Press OK to confirm your choice L gt The selected smart sound setting is applied Adjust sound settings 1 Press Home 2 Press Av to select Setup gt Sound L gt The Sound menu appears 3 Press AVP to select one of the following sound settings e Smart sound Accesses pre defined smart sound settings e Bass Adjusts the bass level e Treble Adjusts the treble level e Volume Adjusts the volume e Balance Adjusts the balance of the right and left speakers to best suit your listening position e Duall Il Selects between audio languages if dual sound is broadcast Mono Stereo Selects between mono or stereo if stereo is broadcast e TV speakers Turns
38. ss Standby On on the remote Numeric buttons control e Use the channel grid see Switch L gt The standby indicator switches to red channels with the channel grid on page To switch off 8 Press OPOWER at the side of the TV Note L gt The standby indicator switches off When you use a favourite list you can only Tip select those channels in the list Though your TV consumes very little power when in standby energy continues to be consumed When not in use for an extended Switch channels with the channel grid period of time disconnect the TV power cable from the power outlet The channel grid allows you to view all available channels in a grid format Downloaded From TV Manual com Manuals Adjust TV volume memmen TEE 3 English 1 Press OK L gt The channel grid appears 2 Press Av to browse the channel grid and preview a channel L gt The channel content is displayed after Qi a lapse of approximately two seconds voume 1 3 When you find a channel of your choice silice press OK to watch L gt The selected channel appears To increase or decrease volume e Press 41 e Press VOLUME on the side of the TV To mute or unmute sound Watch connected devices Press X to mute the sound e Press K again to restore the sound Note Switch on the device before selecting it as a Use
39. t appear in the channel grid View all channels You can exit a favourite list and view all installed channels 1 when watching TV press OK to display he channel grid 2 Press OPTIONS L gt The channel options menu appears Select Show favourite ch gt AII 3 4 Press OK L gt All channels display in the channel grid Note All favourite channels are marked by an asterisk in the channel grid Add a channel to a favourite list 1 When watching TV switch to the channel you want to add to a favourite list see Switch channels on page 8 2 Press AY 4b to select a channel to add to a favourite list 3 Press OPTIONS 14 EN Downloaded From TV Manual com Manuals L gt The channel options menu appears Press AY to select Mark as favourite Press OK L gt The favourite lists appear Un A Press AY to select a favourite list to add he channel to 6 7 Press OK L gt The channel is added to the favourite list Tip e When watching TV press OPTIONS gt Mark as favourite to save the current channel into a favourite list Remove a channel from a favourite list Note Select the favourite list to edit before removing a channel 1 when watching TV press OK to display he channel grid Press OPTIONS L gt The channel options menu appears N Press OK to enter Show favourite ch Press AV to select a favo
40. ted to the TV via HDMI or DVI e Picture format Changes the picture format e Horizontal shift Adjusts the picture horizontally for PC VGA or YPbPr EXT2 or EXT3 e Vertical shift Adjusts the picture vertically for PC VGA or YPbPr EXT2 or EXT3 Change picture format 1 Press FORMAT L gt A picture format bar appears 2 Press AV to selecta picture format L The selected picture format is activated J Press OK to confirm your choice Summary of picture formats The following picture settings can be configured Note Depending on the format of the picture source some picture settings are not available EN 11 English ik Auto format Not for HDMI YPbPr EXT2 EXT3 or PC mode Enlarges the picture automatically to best fit the screen The subtitles remain visible Super zoom Not for HD and PC mode Removes the black bars on the side of 4 3 broadcasts There is minimal distortion 4 3 Shows the classic 4 3 format Subtitle zoom Displays 4 3 pictures over the full area of the screen with sub titles visible Part of the top of the picture is clipped off Movie exp 14 9 Not for HD and PC mode Scales 4 3 format to 14 9 Movie exp 16 9 Not for HD and PC mode Scales 4 3 format to 16 9 Wide screen Stretches the classic 4 3 format to 16 9 LODE LE E Unscaled Available in selected models with PC re
41. terials and components which can be recycled and reused A Downloaded From TV Manual com Manuals When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health A Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health EN 5 English 3 TV overview Remote control ve iv uer feeen source DEMO SCENEA AD am um 5 This section gives you an overview of commonly used TV controls and functions Side controls and indicators D POWER Switches the product on or off The product is not powered off completely unless it is physically unplugged O P CH Switches to the next or previous channel GB SOURCE Selects connected devices o VOLUME I
42. ttings e Repeat e Play once Repeat Shuffle Show info Disconnect a USB storage device Caution Follow this procedure to avoid damage to your USB storage device 1 Press gt BACK to exit the USB browser 2 Wait for five seconds before you disconnect the USB storage device Downloaded From TV Manual com Manuals Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available Check www philips com support for availability Check the current software version 1 Press Home 2 Press Av to select Setup gt Software update gt Current software L gt The TV displays the current software information Change TV preferences 1 Pese Home 2 Select Setup gt Installation gt Preferences 3 Press OK orb to enter Preferences e Location Optimises TV settings for your location home or shop e Volume bar Displays the volume bar when adjusting the volume e EasyLink Enables one touch play and one touch standby between EasyLink compliant devices e Pixel Plus Link Overrides the settings of connected devices and uses the settings of the TV Available only when EasyLink gt On is selected e E sticker For shop mode only Sets the location of the e sticker Press AY 4b to select your preference Press OK Press amp Home to exit Ov Un A
43. ue audio and video input from 150 analogue or digital devices such as DVD r players or game consoles TV ANTENNA 26 EN Downloaded From TV Manual com Manuals 7 SERV U For use by service personnel only Side connectors Downloaded From TV Manual com Manuals 1 USB Data input from USB storage devices USB dum Qa Stereo audio output to headphones or earphones 3 AUDIO L R Audio input from analogue devices connected to VIDEO L AUDIO R YHS VIDEO Composite video input from analogue devices such as VCRs EN 27 English 5 S VIDEO HDMI cable S Video side to be used with Audio L R connectors for camcorder game console etc When you use the S Video side for video signals do not use the Composite video side input for video signals DVI HDMI cable For TV of size 22 inch and smaller PC IN AUDIO For TV of size 26 inch and larger AUDIO IN LEFT RIGHT HDMI 1 DVI 6 HDMI Digital audio and video input from high definition digital devices such as Blu ray players n IB HDMI HDMI 1 HDMI 2 e HDMI cable and HDMI DVI adaptor p or TV of size 22 inch and smaller Bluray Disc PC IN AUDIO For TV of size 26 inch and larger AUDIO IN LEFT RIGHT HDMI 1 DVL HDMI 2 DVI Connect a computer j A Before y
44. umer Care You forgot the code to unlock the TV lock feature Enter 8888 The TV menu is in the wrong language Change the TV menu to your preferred anguage When turning the TV on off to standby you hear a creaking sound from the TV chassis o action is required The creaking sound is normal expansion and contraction of he TV as it cools down and warms up This does not impact performance 32 EN Downloaded From TV Manual com Manuals TV channel issues Previously installed channels do not appear in the channel list e Check that the correct channel list is selected No digital channels were found during the installation e Check that the TV supports DVB T or DVB C in your country See the listed countries on the back of the TV Picture issues The TV is on but there is no picture e Check that the antenna is properly connected to the TV e Check that the correct device is selected as the TV source There is sound but no picture e Check that the picture settings are correctly set There is poor TV reception from an antenna connection e Check that the antenna is properly connected to the TV Loudspeakers unearthed audio devices neon lights high buildings and other large objects can influence reception quality f possible try to improve the reception quality by changing the antenna direction or moving devices away from the TV e If reception on only one chann
45. urite list and ress OK to confirm the choice Press AVP to choose the channel that ou wish to remove from the list Press OPTIONS D 9 ress AY to select Unmark as fav Press OK L gt The channel is removed from the favourite list CONDO WwW KRW Use timers You can set timers to switch the TV on or switch to standby at a specified time Automatically switch the TV to standby sleeptimer Sleeptimer switches the TV to standby after a pre defined period of time Tip You can always switch off your TV earlier or reset the sleeptimer during the countdown Press amp Home Press AY 4b to select Setup gt Features gt Sleeptimer L gt The Sleeptimer menu appears NA J Press lt P to set the sleep time L gt The sleeptimer can be up to 180 minutes in steps of five minutes If set to zero minutes the sleeptimer is switched off 4 Press OK to activate the sleeptimer L gt The TV switches to standby after the pre defined period of time Automatically switch the TV on on timer You can switch the TV to a specified channel at a specified time from standby Press Home Press AY 4b to select Setup gt Features gt On timer Press P to enter the On timer menu Press AY 4b to select Activate and set a frequency Daily Once or Off Press OK to confirm Press AY 4b to select Time and set the starting time N DOU
46. y as intended by the manufacturer e The caution sign printed on the back of the TV indicates risk of electric shock Never remove the TV cover Always contact Philips Customer Support for service or repairs LA A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION ADVERTENCIA NO ABRIR RIESGO DE CHOQUE ELECTRICO Any operation expressly prohibited in this manual or any adjustments and assembly procedures not recommended or authorised in this manual shall void the warranty Pixel characteristics This LCD product has a high number of colour pixels Although it has effective pixels of 99 99976 or more black dots or 2 EN Downloaded From TV Manual com Manuals bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Compliance with EMF oninklijke Philips Electronics N V manufactures and sells many products argeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles is to take all necessary health and safety measures for our products to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products Philips is committed
Download Pdf Manuals
Related Search