Home

Evolis Настанова користувача SECURION

1. t is very important to protect the print head and any other related component handled against any electrostatic discharge The print head is a fragile component of your printer To prevent any damage to it m Before cleaning the print head disconnect the printer from its power supply E Comply with the cleaning cycles E Never put the print head into contact with pointed and or metal objects m Avoid direct contact between the surface of the print head and the fingers This could result in an altered print quality or even permanent damage to the print head SECURIOMN 35 Clean the print head in accordance with the following instructions LL hiit i NA a 44 i AANA ANY nS z tg 1 Turn off your equipment by 2 Open the printer cover loosen the pushing the ON OFF print head bracket and put It into button on the rear panel the vertical position 3 Take a cotton swab and press the middle of the tube until a click is heard The cotton becomes saturated with alcohol 4 Locate the print head and carefully rub the cotton swab from right to left along the print head for a few seconds 5 Lower and lock the print head bracket 6 Close the cover The printer is again ready for operation Cr After a cleaning cycle wait 2 minutes until all the cleaning fluid evaporates before using the printer Remove the cards from the reject box Your Securion printer is equipped with a reje
2. Card orientation Chip cards must be installed in the card feeder so that the chip is downwards as shown below 1 Remove the feeder from the printer as shown 2 Lower the spring system as shown and insert 100 chip cards of 0 76 mm 30mil at most chip downwards 3 Put the feeder back in the printer Then press on the top of the feeder until it clicks SECURI N 53 Interface of the Contact Station The Dualys is fitted with a DB 9 female connector on the back of the printer This connector directly connected to the Contact Station inside the printer is also connected to an external coupler to pro gram the chip DB 9 Connector pins Chip card contact points 1 C1 V c c C2 reset to 0 C3 Clock C4 reserved C5 Ground C6 Vpp C7 E S C8 reserved C9 Ground when the chip is commuted with the Contact Station WO On HU BW N A sequence of commands must be sent via the interface of the printer to insert a card in the prin ter and then place it under the Station to establish contact The command sequence is the following Sending the Sis sequence m One card is moved from the feeder to the Contact Station and stops under it m The card is pushed up to come into contact with the Station m The printer connects the Contact Station to the DB 9 connector m The chip may be programmed via the serial or USB interface of the computer and the external coupler S Check the Programmin
3. j Would you like to install Hicrasaft MET Framework 1 1 Packager License Agreement copy of this hene as swealeo for printing al bttp igo minosafi cowvfwhukPLinkid L413 SUPPLEMENTAL END USEE LICENSE AGEEEWEWNT POR hearse ABT ARE have ad underbocd aid agez bo the tema of he Erid U rer Licence Agreement and so Agap by cicking lagte and proceading bo wee thi product aoee f donot agies Cancel The installation process is now complete Click on OK to continue with the driver s setup if Microsoft NET Framework 1 1 Setup E Installation of Microsoft MET Framework 1 1 t amp complete 6 Setup is performed through a seven step process Make sure you stick precisely to the installation guidelines SECURIOMN 16 Step 1 disconnect the data cable Ws ep el ie loonie Welcome to Primer Drier setep wizard for your bene Secumon Prois This sized wall guide you through each step of fhe setup process IMPORTANT Inthe first place make sure thet the LES 6 Cable is disconme cied fom your Evolis SECU on Primjer before proceeding to he nai sep Step 2 accept the limited warranty conditions EE ep 2 Evolis Serumo Lrmted Warranty Ewolis Printed Waranty Eygi Cad Printer T upsa limded yasr aniy E Pina model Ewi Secuion T PAOOUCT NSFECTIOH UPON RECEIPT Tou mud inept al components of the Eval plache cand pinter delivered bo you as S000 Sr YOU EERE E lithe event ol a mang
4. m 6 panel YMCKO K color ribbon 200 cards roll m 1 2 panel YMCKO color ribbon 400 cards roll m Monochrome ribbons 1 000 cards roll available in black red green blue white gold and silver SECURI M 48 Types of film for lamination m Generic thin holographic overlay film full card surface 400 cards roll m Clear patch 1 mil film 200 cards roll m Clear patch 0 6 mil film 200 cards roll E Special patches and thin overlay films upon request Options m Encoding options can be combined Magnetic stripe encoder ISO 7811 or JIS2 HiCo LoCo Smart contact station ISO 7816 2 Smart contact station and encoding unit PC SC EMV 2000 1 Contactless encoding unit ISO 14443A B ISO 15693 Mifare DesFire HID iCLASS Other types upon request m 100 card additional feeder Ruby Lagoon Glacier Warranty Use Evolis Genuine products for best performance and extended lifespan of your printer E Printer lamination module print head and lamination hot roller a 2 year warranty with a maximum of 100 000 Inserted cards which ever comes first Subject to observance of specific conditions and use of Evolis genuine consumables Card types All PVC Composite PVC cards Card format ISO CR 80 ISO 7810 53 98 mm x 85 60 mm 3 375 x 2 125 Card thickness From 0 25 mm 10 mil to 1 mm 40 mil No lamination under 0 50 mm 20 mil recommended from 0 76 mm 30 mil min Card feeder capacity 100 cards 0 76 mm 30 mil Card output
5. printer cover feeder as Indicated E baie Y 3 Insert the cards into the Adjust the gauge setting in terms feeder as of the thickness indicated of your cards printable face down SECURION 12 6 Reclose the printer cover 5 Put the feeder back into place in the printer until it Clicks in place Use only the types of cards on the List of Consumables in this manual Do not touch the printable surface of the cards the printing quality depends on this B Do not use cards that are damaged bent or that have an embossed texture Always store the blank cards in a clean and dust free location Adjustment of the thickness The Securion printer is equipped with a manual system for setting the thickness of the cards which is accessible either through the feeder frame or through the inside of the printing module when the print head bracket Is open EA The Securion printer accepts card thickness between 0 25 mm 10 mil and 1 mm 40 mil The factory thickness setting of the cards is 0 76 mm 30 mil 1 With the 2 Adjust the cover open thickness of the remove the cards used by moving the operating handle from right to left to the desired card thickness feeder from the printer as indicated 3 Replace the feeder in the printer Then press on the top of the feeder until a CLICK is heard Close the cover SECURION 13 To adjust the thickness of the cards from
6. Advises you that failure to take or avoid a specific action could result in physical harm to you or could result in physical damage to the hardware Warranty Information Refer to the Warranty booklet enclosed with your Evolis printer for terms and conditions Return Materials Authorization In order to make a warranty claim you must contact an Evolis Reseller You will be responsible tor packa ging the printer tor shipment and the costs of shipping and insurance of the printer from the point of use of the printer to the Evolis Reseller The Evolis Reseller will bear the costs of shipping and insuring the printer trom the repair location to the address trom which the printer was shipped Before returning any equipment for in warranty or out of warranty repair contact an Evolis Reseller or an Evolis Repair Center ERC for a Return Materials Authorization RMA number Repack the equip ment in the original packing material and mark the RMA number clearly on the outside of the box For more information about RMA or Evolis warranty statements refer to the Warranty booklet enclosed with your Evolis printer Product Disposal WEEE Directive This symbol indicates that when the last user wishes to discard this product it must be sent to appropriate facilities for recovery and recycling By not discarding this product along with other household type waste the volume of waste sent to incinerators or landfills will be reduced and natural resources
7. Card Printer Manufacturer s Address 29 avenue de la Fontaine Z I Angers Beaucouze 49070 Beaucouze France Material Designation Securion Year of Manufacture 2007 the undersigned Serge Olivier Declare that have received the assumption of the above material used and installed in accordance with the notice with the essential requi rements of Directives 73 23 CEE and 89 336 CEE modified by 92 31 CEE and 93 68 CEE by the application of the following regulations EN 60950 1 of 2001 EN 55022 Class B of 1998 A1 2000 A2 2003 EN 55024 of 1998 A1 2001 A2 2003 EN 61000 3 2 of 2000 EN 61000 3 3 of 2000 A1 of 2001 Full name Serge Olivier Signature Title Technical Manager Date January 2007 EUROPE Norway Only This product is designed for IT power system with phase to phase voltage 230V Earth grounding Is via the polari zed 3 wire power cord FI Laite on liitettava suojamaadoitus koskettimilla varustettuun pistorasiaan SE Apparaten skall anslutas till jordat uttag NO Apparatet ma tilkoples jordet stikkontakt C FCC Statement For U S A Federal Communications Commission Radio Frequency Interferences Statement Securion models conform to the following specifications FCC Part 15 Subpart A Section 15 107 a and Section 15 109 a Class B digital device Supplemental information This equipment has been tested and finds to comply with the limits for a Class B digital device pu
8. card in the feeder Open the printer cover remove the card feeder insert new cards carefully observing the direction of introduction then replace the feeder Close the cover The printer resumes Its activity Ribbon error The printer has detected an error linked to the print ribbon Open the cover loosen the print head bracket and turn it vertically to provide free access to the ribbon Replace the ribbon if it has been fully used If not rewind the ribbon on the receiving roller making several turns Make sure there Is good tension between the feed roller and the receiving roller Lower the print head bracket and make sure It Is locked Close the cover The printer resumes operation Lam Rib error Film error in the lamination unit Open the printer cover to get access to the lamination station If the film has reached the end replace it Otherwise release the film carefully by pulling it toward you Be careful not to damage the equipment by pulling violently S Rewind part of the new film on the receiving roller the left hand roller then put it in place making sure it is correctly engaged against the back stop Reclose the cover The printer resumes operation Need cleaning The printer has detected that a cleaning cycle is required You have disregarded the alert messages given by the equipment Immediately maintain your equipment correctly stopping all printing in order to proceed with the cleaning If you personal
9. components must remain accessible at all times to permit emergency action This product must be connected to a correctly protected and grounded electrical installation Connecting the data cable The data cable USB Ethernet or other must never be connected before the installation of the printer driver has been completed Refer to Chapter 2 1 and carefully follow these instructions installing the ribl The Evolis Securion printer uses two types of ribbons m Color or monochrome ribbons for the printing module identifiable by their core which is equip ped with a toothed wheel Special films for the laminating module characterized by their hollow core The Evolis original ribbons and films are specially designed to guarantee optimum operation J of your equipment without any risk of damage The use of films or ribbons from any other source than Evolis could seriously damage the print head and the heating roller of the lami nating station consequently entailing the immediate interruption of the factory warranty SECURION 09 For optimum printing and laminating quality Evolis recommends cleaning all the equipment each time a ribbon is changed It is up to the user to make this determination provided however that he makes sure to comply with the mandatory cleaning cycles in order to keep the equipment in perfect operating conditions consult the chapter on Ordinary Maintenance The validity of the factory guara
10. feeder and the card in the printer itself m Verify the presence of cards in the feeder E Check that there is no jamming In that case the status LED would be red 3 Check the ribbon and the laminating film m Make sure the ribbon and the laminating film are correctly installed and that the printer head bracket is tight 4 Print a test card See the chapter Print and interpret a test card 5 Check the printer s interface cable m Check the connection to the computer and to the printer m Try using another cable of the same type 6 Check the print driver m Check for the presence of the print driver of the Securion printer in the Windows parameters m Check the computer s printing parameters m Make sure the Securion printer is selected as the default printer OD A blank card is ejected from the printer 1 Check the ribbon m Make sure the ribbon is not finished or cut Replace or reinstall the ribbon as necessary 2 Check the printer interface cable m Check the printer s interface cable m Check the connection to the computer and to the printer m Try using another cable of the same type 3 Components of the print head are perhaps damaged m Print atest card If the test card does not print contact your dealer for a replacement for the print head SECURIOM 44 The print quality is not sufficient Sa 1 The contrast and brightness parameters must be modified m Lack of contrast and color saturation increase the contrast a
11. hopper capacity 100 cards 0 76 mm 30 mil Printer size Without card hopper L 562 7 mm x W 262 16 mm x H 274 64 mm L 22 15 x W 10 32 x H 10 81 With card hopper L 658 2 mm x W 262 16 mm x H 274 64 mm L 25 91 x W 10 32 x H 10 81 Printer weight 15 4 Kg 33 15 Lbs Connections USB and Ethernet ports USB Cable supplied Electrical Power supply 110 230 Volts AC 2 A 60 50 Hertz Printer 24 Volts DC 6 25A Environmental Min Max operating temperature 15 30 C 59 86 F Humidity 20 to 65 non condensing Min Max storage temperature 5 70 C 23 158 F Storage humidity 20 to 70 non condensing Operating ventilation free air SECURIC M 49 Part Number E7001E BASIC E7002E MAG ISO E7003E SMART EOMN7007E SMART amp C TLESS EOMN7000E MAG ISO SMART amp C TLESS Part Number Product Description Securion Basic Basic printer amp laminator without option USB and Ethernet Securion Mag ISO Printer amp Laminator with Dual HICO LOCO Magnetic Stripe Card Encoder USB and Ethernet Securion Smart Printer amp Laminator with Smart Card Contact Station USB and Ethernet Securion Smart amp Contactless with Dual Chip Encoder Printer with Smart Contact Station Contactless Antenna Dual Chip Encoder USB and Ethernet USB driven encoder Securion Mag ISO Smart amp Contactless with Dual Chip Encoder Printer with Dual HICO LOCO Magnetic Stripe Card Encoder Smart Contact Station
12. i pe Ma SECUR TE LEX N gt Wi Securion User Guide part number KUQ8E Rev AO Evolis Card Printer March 2007 Ce V L l S Copyright Information Evolis Card Printer March 2007 All rights reserved Copyright Notice Users must respect the copyright laws applicable in their country This manual must not be photoco pied translated reproduced or transmitted in whole or in part tor any reason and by the means that might be albeit electronic or mechanical without the express written authorisation of the company Evolis Card Printer All information contained herein may be subject to modification without prior notice Evolis Card Printer accepts no liability for any possible errors herein nor tor any accidental damage or damage caused through the dissemination or the use of this manual Trademarks Securion is a trademark and Evolis is a registered trademark of Evolis Card Printer Windows and MS DOS are registered trademarks of Microsoft Corp All other trademarks or registered trademarks are marks of their respective holders eMedia Card Designer is a trademark of Mediasoft Technologies Icons Throughout this manual different icons highlight important information as follows P Indicates information that emphasizes or supplements important points of the main text Advises you of information that is essential to complete a task or points out the importance of specific information in the text
13. menu the LCD display becomes a parametering dialog and help interface Architecture of the menu The bottom line on the display makes it possible to specify at any time the function of the corres ponding key in the context menu In general and unless otherwise indicated this is how the browsing Is done Selection Line Browse Line ESC Escape Interruption of the Validation of the operation and return parameter and return to previous level to previous level lt Scrolling back Scrolling forward gt OK When the printer is operating The display oe normally the hardware s now becomes ETTI browsing menu is activated by pressing one of the buttons eooo This configuration menu gives access to most of the printer s parameters The following diagram shows the tree structure of this menu the options that can be parametered as well as the browsing mode to be applied to get a menu or activate a parameter SECURION 23 Ready MENU CONFIG OK LAMINATION OK Display lamination type CARD EXIT OK Display Card exit mode a REJECT BOX of Cards Reset of Cards gt gt STANDBY MODE Disable gt 11 99 to RIBBON TYPE OK gt MAGNETIC OPTIOK LAMINATOR PRINTER OK Display ribbon type OK FILM TYPE OK Display Film type TEMP C OK Printer temperature SPEED OK Lamination speed OFFSET OK Patch offset CLEANING OK PRIN
14. order to prevent problems linked to connecting your printer to the local network the DCHP mode is factory activated Configuration Description Factory parameters Parameters CONFIG LAMINATION Off No lamination Default Front Lamination on front of card only Back Lamination on back of card only Dual side Lamination on both sides of the card CARD EXIT Front visible Card ejected with front face visible Default Back visible Card ejected with back side visible The first card printed is on top of the pile in the hopper Default The card is ejected in the position it has in the lamination station REJECT BOX Reinitialize Initialization of internal counter indicating the number Default of cards rejected value 0 of cards Indicates the number of cards rejected since the last reinitialization STANDBY Deactivated The printer never goes into standby mode Default MODE 1 99 In minutes Duration of inactivity prior to printer going on standby Display of printer information PRINTER RIBBON TYPE Display of type of ribbon parametered through the print driver menu MAGNETIC OPT Type of magnetic encoder installed in machine Parameters of the lamination station LAMINATOR FILM TYPE Patch Deposits a thick PET film on the surface of the card This type of film does not cover the entire card Continuous Deposits a fine overlay over the entire surface of the card overlay Off No lamination Default TEMP C Display of temperature of the lamination
15. perform the following operations Connect the printer to the main power supply Connecting to the electrical system Before hooking up to the electrical system make sure the switch on the back of the printer is on OFF 0 Turn off the printer by pulling the plug out of the socket which must always be accessible This product must be connected to an electrical installation that is correctly protected and grounded Fl Laite on liitett v suojamaadoitus koskettimilla varustettuun pistorasiaan NO Apparatet ma tilkoples jordet stikkontakt SE Apparaten skall anslutas till jordat uttag Connect the power supply cord to the power supply then attach the power cord connector to the printer Then connect the end of the power supply cord to a grounded system outlet Power up the printer by turning the switch to ON 1 The control panel display lights up and the message INITIALIZATION is displayed Once the star tup sequence Is completed the menu displays READY and the driver LED Is green and must be Steady If the display does not light up when the power Is turned on or if the LED is not green and or if it flashes this means that the installation was not done correctly or possibly that the printer is not operating properly Check the installation BS GON Prior to any maintenance action always turn the power switch to OFF 0 and disconnect the power supply cable For your own safety these two
16. the ejection has not produced any result try to free the card manually making sure not to touch the hot surfaces on the lamination unit If the lamination unit is too hot turn off the printer and wait for the module to cool off lit will take several hours Again try to free the card manually If despite all your attempts the card continues to be jammed contact your Evolis dealer who can provide a specialized technician to help you on site Never use a tool screwdriver pointed object to free the card You would risk serious damage to the rollers and specifically the unit s hot roller This damage would not be eligible for any coverage under the warranty Once the card is free make sure the film is correctly positioned then close the printer cover The printer resumes operation SECURION 43 Upgrade the print quality The following information will help you solve potential print quality problems that can arise when using your printer If despite this information you cannot solve the problem contact your Evolis dealer QD Nothing prints 1 Check your equipment s power supply Make sure that m The power cord is correctly connected to the printer and to a working outlet m The switch on the back of the printer is ON 1 The printer is powered The display must show the Ready message and the status LED must be fixed green in color m The power supply used is the one shipped with the printer 2 Check the card
17. the inside of the printer 1 Open the cover of the printer by pressing on the opening handle and turning It 2 Remove the ribbon if it is In the printer Then adjust the thickness of the cards used by moving the handle from right to left to the desired card thickness 3 Re install the ribbon in the printer then close the cover Once the personalization cycle is completed the card is delivered in the hopper located on the left side of the unit The user can choose from among 3 ways of ejecting the card m Front face visible First card under the stack m Rear face visible First card on top of the stack m Ejection in the position of the card as it comes out of the lamination station SECURION 14 Setting parameters Defining the parameters of the printer and of its driver is a highly important step and requires very special attention As a matter of fact a poorly defined film or improper settings are factors that have a negative impact on the quality of personalization It is therefore essential to proceed in stages changing the parameters only when you are completely sure Evolis gives you at all times the ability to return to the factory settings if the adjustments made do not give the expected results The application of an improper lamination station heating temperature can result in the destruction of the card and of the film and in extreme cases can affect the station itself Be caref
18. the unit and its MAC address necessary for hooking up to the Ethernet network TCP IP Finally the encoding and printing module includes a number of components including 17 300 dpi thermal color printing head 18 Card cleaning roller absorption of residual dust on cards 19 Gauge for adjusting card thickness from 0 25 mm 10 mil to 1 mm 40 mil 20 Magnetic encoding head option 21 Smart card contact station 22 Contactless card encoding antenna RFID pao A ae aS yeh 17 419 ria Er SECURI ON 07 The Evolis Securion printer must be set up in a dry well ventilated location protected against dust and air currents In point of fact during the lamination operation the temperature of the module can attain a peak of 180 it is therefore recommended that the instructions regarding the operating environment be followed In addition make sure you install your Securion on a sturdy flat surface that can support its weight of around 15 kg 33 Lbs Finally it is essential to allow free access to the connectors and to the power switch located in back of the unit Because of the weight of the entire unit 15 kg 33 Lbs and to prevent any physical damage do not attempt to install the machine by yourself Check the items shipped The Evolis Securion printer is shipped with a set of accessories that we invite you to examine Please take note that this list may vary in terms
19. use your printer If you choose to install your printer via an Ethernet TCP IP port please download an additional guide Securion User Guide Ethernet Setup from www evolis com en supservices download_UGQO asp Select Securion then Ethernet Setup Choose the appropriate language and click the download button SECURION 19 Properties of the driver Before using your printer you must determine your personalized parameters E ype of ribbon for printing the cards E Type of film for laminating m Default parameter settings m Adjustment of encoding parameters KS You will find more detailed information on Evolis ribbons and films inthe Evolis Genuine Product Consumables List section n general it is recommended to retain the default parameters determined by the print driver Modification of these parameters by an uninformed user could lead to a poor quality of per sonalization as well as to hardware damage So stay alert and contact your Evolis dealer who will guide you in adjusting these parameters if applicable These printing parameters are accessible E From the Start button located at the bottom left on the Windows task bar select Printers and Faxes m Choose your printer by left clicking with the mouse for example Evolis Securion m Click again but with right mouse key to bring up a menu and select Properties An initial screen for setting the equipment properties paramete
20. with a simple click from the Windows driver however the encoders of the Securion Mag are sent adjusted to high coercivity HICO by default unless specifically requested on the order Location of the magnetic encoder The magnetic encoder is a module installed in the factory on Securion Mag printers The writing and reading head is placed under the path of the cards and after the print head he encoding sequence of a card is still carried out before printing Cards with a magnetic track must be installed in the feeder so the magnetic strip faces upwards as follows 2 Lower the spring system as shown and insert 100 magnetic cards of 0 76 mm 30mil at most 1 Remove the feeder from the printer as shown 3 Put the feeder back in the printer Then press on the top of the feeder until it clicks Setting the Windows Driver When first installing the Windows driver it is necessary to parameterise the functions of the magne tic encoder The functions of the magnetic encoder are accessible from the Tools dialog box of the driver by clicking the Encoding Definition button SECURION 51 The Magnetic Encoder dialog box opens on selec ting the Encoding Definition button Track format allows us to choose the ISO standard required for each track See the table in this Annexe for the information concerning the ISO 7811 standards Coercivity parameterises the magnetic encoder in pnp e eea high HIC
21. Contactless Antenna Dual Chip Encoder USB and Ethernet USB driven encoder Multi Panel Color Ribbons R3314 R3013 R3011 R3012 Product Description 6 Panel Color Ribbon YMCKOK 200 cards roll 5 Half Panel Color Ribbon 1 2 YMCKO 400 cards roll 5 Panel Color Ribbon YMCKO 200 cards roll 2 Panel Monochrome KO 500 cards roll Security amp Laminator Films R4711 R4721 R4832 Monochrome Ribbons R2011 R2012 R2013 R2014 R2015 Clear Patch 0 6 mil Box of 10 rolls 200 cards roll Clear Patch 1 0 mil Box of 10 rolls 200 cards roll Full card varnish Generic Hologram Security Box of 10 rolls Continuous film around 400 cards roll Black Monochrome Ribbon 1000 cards roll Blue Monochrome Ribbon 1000 cards roll Red Monochrome Ribbon 1000 cards roll Green Monochrome Ribbon 1000 cards roll White Monochrome Ribbon 1000 cards roll For specific security requirements as per your application Evolis and its Partners are willing to consider supplying lamination films that are not listed above Please contact your Evolis reseller for more details SECURIPM 50 Magnet Securion printers with a magnetic stripe card encoder are called Securion Mag printers The opera ting mode of a Securion Mag printer is identical to that of a Securion printer The magnetic encoder encodes tracks ISO 1 2 and 3 in a single passage and then checks the data Set in high coercivity HICO or in low coercivity LOCO
22. Installing the ribbons aaaaaaaa aeaaaee 09 Monochrome or color ribbon Laminating film Installing the cards l a aaaea aaaeeeaa 12 Types of cards Placement in the feeder Adjustment of thickness Removing the personalized cards 14 FJ Setting of parameters Windows print driver 00 000 00 20 ccc eee 15 Installation of the print driver Manual installation of the driver Properties of the driver Printer MeNUS 0 0 06 a 23 Discovering the printer menu Architecture of the menu Parameters EJ Error messages and diagnostics Notification of messages 0 000 00 cece 26 LCD display and LED indicator Port Monitor Interpretation of messages 0 0000 2208 26 Status messages Alert messages Error messages Diagnostics assistance 0 00 0 c cece eee 30 Print and interpret a test card Identify the software versions installed C DS CIrIE J VA Servicing and Maintenance Ordinary maintenace aaaea oaae eee 32 Clean the card feed module Service the cleaning roller Clean the print head Remove the cards from the reject box Maintenance aaaea anaren erraren rnrn rerne 37 Replace the cleaning roller Replace the print head Update the Firmware Update the print driver Troubleshooting 0 0 aana c ccc c eee 42 Free a card in the print unit Free a card in the lamination unit Free a card in the
23. Kensington security mechanism Printer specifications m Color printing module and laminating unit m 300 dpi print head 11 8 dots mm m USB amp Ethernet TCP IP connection m 16 Mb RAM allowing two card storages front amp back E Flip over station for dual sided printing or laminating m Detachable feeder with a capacity of 100 cards 0 76 mm or 30 mill m Output hopper with a capacity of 100 cards 0 76 mm or 30 mil m Reject box for 15 cards 0 76 mm or 30 mill m Iwo line LCD display and a status LED m Locking system to secure access to blank cards ribbons films and rejected cards m Support for a Kensington locking system Print Mode m Color dye sublimation and monochrome thermal transfer m Enhanced color management system for high quality pictures m Dual sided and edge to edge printing Lamination Mode m Full card varnish and patch films E Dual sided lamination m Speed range 2 mm s to 18 mm s 0 08 inch s to 0 71 inch s m Temperature range 100 C to 180 C 212 F to 356 F Printing and laminating speed Personalization throughput will depend on card design and lamination speed settings m YMCK K 1 0 mil patch single side 85 to 105 cards hour m YMCK 1 0 mil patch single side 95 to 120 cards hour Supported platforms m Windows XP 2003 and Vista 32 amp 64 bits Ribbon types for the printer module E 2 panel KO black monochrome ribbon 500 cards roll m 5 panel YMCKO color ribbon 200 cards roll
24. O or low LOCO coercivity A magnetic Mo 7 e m track encoded in high coercivity is more resistant to exterior disturbances than a magnetic track enco ded in low coercivity Direct encoding allows the direct encoding of one or more magnetic tracks from this window sim ply by selecting them and entering the data to be encoded Click on the Execute encoding but ton to start the encoding cycle Automatic extraction allows cards with magnetic tracks to be encoded from Windows applications such as Word for example A text field surrounded by the characters and or another cha racter to be defined by the user may be interpreted as an encoding command by the driver Only use cards with magnetic tracks conform to ISO 7810 and ISO 7811 J 0 work properly the magnetic track must be moulded in the card Never use a card with a glued magnetic track Cleaning of the magnetic encoder The head of a magnetic encoder needs regular cleaning to be able to assure the integrity of the data encoded in the cards The magnetic encoder is cleaned when the printer Is the object of a cleaning sequence with the pre saturated cards refer to the Cleaning chapter in this manual for further information Repeated passages of the cleaning card inside the printer clean the card transport rollers the clea ning roller and the reading writing head of the magnetic encoder If between two printer cleaning sessions every 1000 cards in
25. Properties pect Main tab Orientation of the printed card Number of copies Landscape Rotate by 180 fe Secunon Reseau Properties Man Graphic Lamination Tools r Magnetic Encoder Control Landscape l Aaaa by 120 Dieci Printer Corinal Printer Set Test Porter Sef Clearing Panter Set Agustment Rect Card Direct command to printer 4 Copias I pee Lsedul links SECURISN Geom Direct communication wih Ponter Dialog with Printer Tools tab i Setting parameters and testing SECURI Pn of the magnetic encoding options i er Testing and diagnostic tools On line help A help file guides you in using each of the parameters of the print manager in terms of the different print modes and criteria selected To familiarize yourself with these different parameters we recommend that you consult this help feature before making any changes Print a test card Tools tab We recommend that you print a Test Card at the time of the first use and that you save it This card stores data that you may be asked to provide if you call Sales Service Default printer Depending on your application it may be important to define your Evolis printer as a default prin ting peripheral device ASS In that event all your print work not just cards but office documentation will be sent to the Evolis printer To define your default printer proceed as follows m Using the S
26. TER OK Start cleaning process gt ADVANCED OK Start rollers SERVICE gt STATUS Pr Serial gt Pr Firmware ES Printer Type gt Pr Head ID OK OK OK OK OK OK OK Display Magnetic option type OK OK OK OK OK OK Serial Number OK Type of Printer OK Print head Identification OK Printer firmware version gt Lam Firmware OK Laminator firmware version gt Next Cleaning OK xxxx cards to go OK TECH CARDS OK Self test OK Start issuing a test card gt Printer Status OK Start issuing a printer status card OK LCD LANGUAGE OK BACKLIGHT OK CONTRAST OK NETWORK IP ADDRESS MAC ADDRESS DACE MODE SUBNET MASK GATEWAY OK Yyy English gt Custom OK gt English OK 80 Decrease value OK Increase value OK 80 Decrease value OK Increase value OK OK Display current IP Address OK Display MAC Address OK Display DHCP configuration OK Display Subnet Mask Address OK Display Gateway Address SECURI Parameters In the following table you will find all the parameters of the menu classified in the order of display along with their meanings The Default indication means that this parameter is factory activated Make sure not to change their parameters at random This could affect the correct performance of your Evolis Securion printer In
27. and the LED will start to flash when 200 additional cards have been inserted In that event immediately stop the work in progress and proceed with the cleaning If there is no maintenance action on your part the message will remain posted and the factory warranty will be implicitly invalidated for failure to comply with the contractual maintenance requirements SECURICM 32 To service the printer card feed system obtain a pre saturated cleaning card specially designed for the printer A cleaning kit including samples of these cards Is shipped with your Securion printer Repeated running of the card in the printer cleans the card feed rollers the cleaning rollers the print head and the magnetic head if your device has one Proceed as follows 2 Press the latch to loosen the print head bracket and turn it to the right until it is in a vertical position Then remove the print ribbon in the print module 1 Open the printer cover AN wif 4 j FANA OET E Ti aa Pay 3 Remove the print feeder as indicated Remove the cards that are in the feeder Insert the cleaning card in the feeder as indicated Put the feeder back into the printer than press on the top part of the feeder until the click is heard 6 Using the lever adjust the thickness of the card to the MAX position 8 Lower the 9 Go into the display men by pressing one of the print head keys brack
28. ct box whose function is to separate the correctly per sonalized cards from the Incorrect cards The incorrect cards are automatically stored in a reject box with a capacity of 15 cards This reject box must be emptied regularly in order to prevent any jamming of the work in progress This operation is done in two phases 1 Removal of the cards 2 Zero resetting of the rejected card counter to allow the printer to know the fill level of this box SECURION 36 To empty the box and re initialize the counter proceed as follows 1 Open the cover 2 Open the reject box by tilting 3 Reclose the reject of your printer the door to the front and remove box door the cards that are there 4 Press a key on the control panel to access the menu 5 Select CONFIG and confirm by pressing OK then scroll through the menu until REJECT BOX is displayed Confirm by pressing OK 6 Select Reset on the menu and confirm by pressing OK 7 Get out of the menu 8 Close the cover Z Evolis recommends that you empty this box regularly for example at each ribbon change or during maintenance The Evolis printers are designed to offer the user quality of personalization ease of use and equipment longevity However depending on the type and volume of personalized cards as well as the operating environ ment certain elements are able to be exchanged by the user Moreover it is common in the computer world to do regular upgrades of the
29. d also provides you with some essential information such as mw The printer model E The printer serial number m The serial number of the print head kit m The Firmware version installed on the printer m The MAC address of the unit local network operation m The IP address of the unit as well as its mode of attribution Manual or DHCP You will be asked for this test card if you request service under the warranty It is also a very precise source of information for your Evolis dealer in remote support service calls SECURICM 30 Identify the software versions installed As indicated above you can simply identify the software version loaded into your printer thanks to the test card Firmware no You can also identify the version of the print driver installed as follows propos du plote donpression G nie Patsgs Port Awenct Gestion des couleurs i S cuit T Caracirisi A Graphique Uiitaines mee gt Go into the driver proper na i ay fae ties on the print driver Ruban 5 pannas Standard YMCKI logo right click and Sct AE EA S E choose Properties za C Ruban 2 pansa KO 2 Puban marochrone E gt Characteristics tab C Fubar Horane fH gt About button T T bichangemert rapide Eva nban Dietai C Potrat LAJE Paytage D Rosin 12 Copies fi Lint utes SECURION 31 Servicing and Maintenance In this chapter we suggest that you identi
30. d change No printing should be started before this operation has been completed 0 00 09 g Refer to the Clean Card Feed Module chapter to perform this operation Also service the cleaning roller and replace cards and ribbons Your Evolis printer is again ready to personalize your cards SECURIPMNM 40 Update the Firmware Updating the Firmware is a simple operation but if is not carried out fully the result can be a disabled Prior to any update please contact your Evolis dealer who can advise you as to whether or not it is appropriate to carry out this operation In general this type of update is required only in case of a problem or malfunction clearly identified by your Evolis dealer In order to download an update from the www evolis com en supservices access asp site you must first have registered your product with Evolis see chapter Register your product in order to benefit from updates 1 Enter your login and password a page Is displayed 2 Select the Securion printer model and the Firmware selection 3 Accept the download and register the file in a directory on your hard disk The file is stored in compressed zip file You must extract it and save it in a temporary directory 4 Then double click on the file in the directory to start the download 9 When asked by the program click on the Download button to start the operation The downloading Is in process the message Downloading appears on the cont
31. damaged a viable defective conprar ou mut noih Evoke or the Ewok A esale ho sold pou the pninler within ben 70 dave from the deba date of the podaci I pou Read bo giye notices a3 nea ul ee WOU Hi be desned to herve atcepied Ihe podaci and wabad are dain you map hava eqns Eyo ardor iha E yaz Reseller vath respec bo nabh damages co deads upan avery 2 5 COPE OF THE WHAASYTY Evols Card Printer Evair warar bo thre original purchaser that the prie piinter model menhoned above wall be hee hom manufacture or opersbng defect in naiak o workmanship hors period of teas 2 yea ron Fe date of agna punches or mi 100 O00 inserted caide whichever comes frat The migra purchaser mast be able to F Yes have reed and accept as is warnaii siaiemeri Provinse nee Carcal Step 3 select the communication port Way ep 3 Gelert the Prober Port Selectthe connection mode to your Ewas Semon Primier Link yaur printer to your computer ie he local USB Port eue C Enable advanced diagnostic feos Evolis Port Monitor T Elier an If you install your PC in USB mode you can choose to activate the Port Monitor an application that displays all operating error messages on the PC screen SECURIVN 17 Step 4 detect communication port Wait until the setup wizard detects the communication port with your printer to carry on to the next step Estep 4 USE setep Printer detection the setup wizard will
32. e from Information SFBACLTWETS CORP SY FP TVR a gt SP ERICVELT as Technology Equipment VCCI WAcHoat SERRES EESTI EFASE If this is used near a radio or television receiver MRRAR HO TIE LUBY dRL amp e L OT FAL in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual End of life product disposal This symbol indicates that Waste Electrical and Electronic Equipment WEEE must be disposed of separately from normal household waste in order to promote reuse recycling and other forms of recovery and to reduce the quantity of waste to be eliminated though landfill WEEE includes accessories such as remote control batteries AC adaptor etc When you dispose of such products please contact your distribu tor or Evolis at info devolis com SECURION 47 General features m Metal housing with a locker restricting the access to the consumables m Detachable card feeder 100 cards Ruby 300 dpi print head with enhanced colour management system allowing high quality picture printing E Flip over unit available for both printing and lamination modules m Reject box 15 cards m Output hopper 100 cards E Control panel with 2 line LCD and status LED E 16 MByte Ram allowing storage of two full dual sided card designs m Data Ports Securion is delivered with an USB and an Ethernet ports A 6 1 80 m long USB cable is delivered with each printer m Slot to host a
33. e print head You 2 Pick up the new print head and turn it toward will be asked for this you with the code in Stage 3 white connector visible 3 Connect the cable into its 4 Turn the head so seat making sure It Is In that the notice is the correct direction Do visible the not force the mechanism connector Is no as this part Is relatively longer visible sensitive SECURION 39 5 Insert the head vertically into the two 6 Turn the print head by pressing the top of guides so as to lock the fork lugs into the metal piece in order to clip it into the their seats spring mounted part 7 The head is put back tn place 8 Close the printer cover The print head Is now installed Step 3 Setting the parameters of the new print head 1 Power up the printer and make sure It is properly connected to a computer on which the Securion printer print driver is installed 2 Under print driver Properties click on the Tools dialogue box 3 In the Dialogue with the printer portion enter the following command Pkn x X the print head kit number that you read in Step 2 Example if the print head kit number is 179 004 00048 you must enter the command Pkn 179 004 00048 If the print head kit number is not entered correctly printer malfunctions can occur Step 4 Cleaning the printer On the printer display the message Need Cleaning appears Need Cleanins Cleaning is absolutely required after a print hea
34. es E Port Monitor The Port Monitor is a software component that helps you monitor your Evolis printer on a day to day basis When installed on your computer it enables you to visualize the activity of your Evolis Securion unit from your work station No need to move the Port Monitor will alert you as soon as an important message is sent by the printer For more information on this function consult the www evolis com site and download the documen tation relative to installation parameter setting and operation gt Flashing red LED Operator alert to incident work interrupted ler pi ele JFR Q TIE Lee There are three major categories of messages They inform you about the status of your Securion printer E The status messages Inform you about the on going printer activity E The alert messages notify you of the non blocking alarms detected during operation E The error messages call for operator intervention SECURIOMN 26 Status messages These messages Indicate the status of the printer during processing They are displayed to inform the operator and do not require any particular action Message Description Led Initializing Startup under way mk Ready Printer ready and waiting for print work Cooling Cooling of print module under way nk Printing Printing under way m Laminating Laminating under way m Warming Up Preheating of the laminating module under way m Waiting Waiting for the end of process
35. es on the Evolis Internet site This item offers the downloading of the most recent versions of Firmware print drivers and user manuals Evolis printer use and maintenance and an FAQ item to provide answers to the most fre quently asked questions FAQ Frequently asked Questions Register your product to benefit from updates To benefit from driver and Firmware updates you must pre register on the www evolis com site Enter the following address into your browser in Register for download order to get access to the registration form Plaase enter your personnal and company informations then submi the form Your request will be validate by an Evolis sales representathe and you si cee an e mhall wilh your credentials Please fill out the entire form making sure Jf to complete correctly the fields in red Por more inforradion please contact the Erais cusina aave Lenan emeni surrey ols com The fields in red are required You will receive a return confirmation e mail including your personal access codes Tithe Please select a tile First name Leet name Position E mail E mail canlinimaiihoi Printer senal Number Language Fiease selet a language Company Daparmant Alle eee SECURI M 46 Characteristics This chapter covers technical specifications and certifications for the Evolis printer Concerning Safety and Electromagnetic Compatibility Manufacturer s Name Evolis
36. et and 10 Select the CLEANING menu confirm by make sure it pressing OK then select PRINTER and is locked confirm by pressing OK 11 The cleaning cycle is activated the display shows Cleaning SECURION 33 12 At the end of the cycle the card is ejected into the reject box 13 Shift the print head bracket into the vertical position adjust the gauge replace the ribbon put the cards back into the feeder lower and lock the print head bracket 14 Close the cover The printer is again ready to operate _ Following a cleaning cycle wait 2 minutes until all the cleaner is completely evaporated before using the printer Take advantage of this interruption to empty the reject box and clean our print head see below Recommendations Maintenance of the card feed module ensures a high quality of printing Evolis recommends that you per form servicing on each ribbon change Without wali ting for a message to be displayed proceed as descri bed above Service the cleaning roller The function of the cleaning roller is to eliminate any residual dust on the front and rear faces of the cards before they enter the feeder system This roller blue in color therefore systematically becomes dirty This is a sign of its efficacy If this roller remains clean we suggest that you check Its quality by contacting your Evolis dealer in order to replace it if applicable To supplement the servicing of the card feeder system wh
37. flipover unit Improve printing quality Assistance oie oe wochwesegoecereetearsncsssiaeeen beneuacroeesasees 46 Network of Evolis partners Look for information on www evolis com Download updates L Characteristics Declaration of conformity 0 000 00000 000 47 Printer specifications 0 0000 00 00 48 Printer options ccc ccc eens 49 List of Evolis Genuine Product consumables 50 Magnetic encoding 0 0 0 c ccc eee ees 51 Smart card contact station 0 0 02 53 Install the Evolis Securion printer The aim of this first part is to assist you step by step in discovering your new printer and putting it to work for you By taking the time to review these few pages you will get more detailed knowledge about Securion and its capabilities while optimizing the time needed to install and start using the product Evolis Securion is for all users who want to personalize highly secure badges The personalization cycle includes a series of operations that are consistent with the nature of the requirements For example after a first and optional card encoding stage magnetic stripe contact or contactless chip personalization continues with printing on one or both sides of the card The printing process is completed by a lamination cycle that involves putting a protective film on one or both sides of the card The use of holographs
38. fy the ordinary service operations for your Evolis Securion that will enable you to ensure a very high quality of personalization of your plastic cards Keep your Warranty in effect f The factory warranty is subject to strict compliance with ordinary maintenance instructions and specifically to compliance with the equipment cleaning cycle intervals Failure to comply with the procedures described in this chapter entails cancellation of the warranty on your printer and its print head Evolis will not be liable if the printer is used under non approved maintenance conditions Evolis provides you with the following maintenance items available under the following reference item A5011 UltraClean cleaning kit m Five cleaning cards pre saturated with 99 isopropyl alcohol E Five 99 isopropyl based cotton swabs mw A dispenser box of 40 pre saturated cleaning wipes Clean the card feed module Cleaning cycle every 800 cards printed i Maximum interval between two cleaning cycles 1000 printed cards lt Maintenance accessory pre saturated cleaning cards When a cleaning of the card feed module is necessary every 800 cards inserted the message Cleaning required appears on the display and the LED turns red This message is an alert that indicates to the operator that it is necessary to perform the cleaning cycle If the printer is not cleaned after the LED illuminates the message Cleaning required will remain displayed
39. g Guide of the Dualys printer to obtain more complete information on how to program a chip card SECURI M 54
40. holograph ribbons makes it possible to combat fraud and counterfeiting of the badges Evolis offers a wide range of consumables that can be adapted to the needs of an enter prise as requested In addition to great security plastic lamination means greater badge durability generally between 5 and 10 years depending on the quality of the components and the manner in which they will be used Evolis Securion is an ideal personalization solution for company badges student badges drivers licenses identity cards and more generally for any badge requiring a very high quality of printing combined with total security SECURIC N 06 Initial The Evolis Securion printer is comprised of the following components referenced on the diagram 100 card feeder Encoding and printing station Flip over station Defective card reject box with a capacity for 15 cards Card laminating station 100 card capacity hopper 7 4 button control paneland 2 line LCD display 8 LED indicator light for displaying printer activity 9 Centralized locking of the cover to secure all internal components Bm GN Oo O1 The following items are located behind the printer 10 Power supply connector 11 USB computer connector 12 RJ45 Ethernet connector 13 DB9 connector s option 14 Power switch 15 Location of Kensingston type bolt You will also find the identification label 16 Specifically containing the serial number of
41. ich is intended to clean It you can obtain a saturated cleaning cloth and clean this component thoroughly Cleaning cycle on each ribbon change Maintenance accessory cleaning cloths 2 Place the print head bracket into a vertical position Then remove the print ribbon in the print module 1 Open the printer cover SECURIPN 34 3 Locate the 4 Clean the roller with a cleaning cloth cleaning roller from your cleaning kit Eliminate all and release it dust by rubbing the cloth lightly over from its seat the entire surface of the roller 5 When it is dry replace the roller into the printer making sure it IS properly positioned 6 Put the ribbon back in its place lower and lock the print head bracket 7 Close the cover The printer is again available for use After a cleaning cycle wait 2 minutes for Y the cleaning fluid to evaporate completely before using the printer Cleaning cycle at each ribbon change Maintenance accessory cotton swab saturated with isopropyl alcohol l The print head is cleaned at the time the inside of the printer is cleaned see above However in order to preserve the original printing quality and to reduce the incidents created by the presence of surplus ink on the surface of the print head it is recommended that the print head be clea ned regularly at each ribbon change using the cotton swabs supplied with the UltraClean cleaning kit
42. ing mk Processing Processing under way mk Cleaning Cleaning procedure under way mk Downloading Loading of Firmware under way nk Do not disconnect the printer or the PC connection to permit proper performance of this operation Restarting The printer restarts after loading of the Firmware Alert messages The alert messages in turn require operator intervention to resolve the cause of this alert They do not in any way block the proper completion of processing under way However we recommend that you intervene quickly in order to prevent any future difficulties Message Description Led Need cleaning The printer has detected that a cleaning cycle will be required shortly You have printed more than 800 cards since the last maintenance The acceptable limit between two maintenances is 1000 cards Make sure your equipment is well maintained by interrupting your printing work as soon as possible in order to do a cleaning Warning failure to clean leads to damage to your equipment and the systematic invalidation of all factory warranties Reject Box full The internal printer counter has detected that the box containing rejected cards is full Please open the printer cover lower the cover giving access to this box and remove the cards Go into the display menu select CONFIG then REJECT BOX and confirm Reset SECURION 27 Error messages Message Description Led Feeder empty The printer indicates the absence of a
43. ize more than 5 cards the factory warranty will be invalidated because you have not done maintenance at the times specified by the warranty clauses in the manual furnished with your equipment Reject box full The printer s internal counter has detected that the box containing the rejected cards is full The printer must reject one more card and It cannot perform that task The work Is therefore interrupted Open the printer cover lower the cover giving access to De this box and remove the cards found there Go into the display menu select CONFIG then REJECT BOX and confirm the Reset selection SECURIPNM 28 Error messages Message Head brckt open Printhead error Mechanical error Lamin mech error Lamin temp error Laminator error Lamin Rib error Description The head bracket supporting the printer s print head is not correctly locked in place Open the equipment cover press down on the head bracket until there is a Click then close the cover The printer resumes operation The printer has detected a problem with the print head Printing process is on hold Contact your Evolis dealer to get help The printer has detected a problem with feeding the card into the print module or the flipover station Lift the equipment cover and move the head bracket into vertical position Remove the ribbon Carefully remove the blocked card making sure not to damage the printer and its components Close
44. ls by simply following the instruc tions very carefully Before doing anything else please contact your Evolis dealer in order to check with him whether it is advisable to replace the print head If applicable the dealer will furnish you with a replacement print head _ During the printer warranty period Evolis has put in place a program for the replacement of defective print heads Your equipment is eligible for this program if m You use only Evolis consumables ribbons and maintenance products m You have scrupulously complied with the equipment maintenance cycles E You work in a dust free environment in accordance with technical specifications m You use flat cards without any rough areas that could damage the surface of the print head SECURICN 38 To complete the exchange of the print head proceed as follows j Before changing a print head make sure the printer is OFF 0 Step 1 Removing the defective print head 1 Open the A 2 Loosen the print equipment head bracket and cover put it into a vertical position and locate the print head 4 Turn the head carefully and 3 Press down on the metal piece at the bottom as Indicated disconnect the connector in order to release the lugs of the holding forks then linked to the cable without pull the lugs out from their seat forcing the mechanism Step 2 Installing the new print head 1 Note the code Indicated on the white ticket affixed to th
45. m Start the MS Word application m Click File on the menu bar then click on Formatting m The Paper tab proposes Paper format select type Evolis Card CR80 m Under the Margins tab set all the margins to 0 then under Orientation select Landscape m Close the window by clicking on OK Your Word window should now look like this Tema oe abe J AFET EEDE hE Your are ready to personalize your card by entering the different composition components mLogo and illustration midentification photo mFixed and variable text mBar code etc be U i eee ee Ba eed jj armanna nn normmna a bhi kem minha mm ee eee i Example Please note that this example does not g propose to initiate the operator on ope rating the MS Word application Its pur pose is simply to establish a relationship bet ween the graphics of a card and the parameters of the Evolis Securion driver that are necessary for the printing operation E FEF limpa ties ROB se a MML Poe imi im uli Wi Moa oS i m Setting the parameters of the Evolis Securion print driver from MS Word m Click on File on the menu bar then click on Print m The dialog box informs you that the Evolis printer has been selected Now click on Properties The Evolis Securion drive dialog box appears The printing parameters for this graphics example are Characteristics tab m Orientation Front landscape m Orientation Back land
46. nd brightness parameters in the print driver configuration 2 The type of card used may be inappropriate m Make sure the type of cards used corresponds to the required specifications See the Technical Card chapter in this manual for more information The texture of the card is rough or not perfectly flat Try to print using another type of card Partial or incorrect printing 1 Check the parameters defined for the printing m Make sure no element of your formatting is outside the print margins m Check the orientation of the document selected in the configuration of the print driver Landscape or Portrait 2 Check the printer interface cable m f some unusual characters print out make sure you are using the interface cable appropriate for your printer m Check the connection to the computer and to the printer m Try using another cable of the same type 3 Make sure the printer is clean E Clean the inside of the printer the cleaning rollers and the print head if necessary See the Maintenance chapter of this manual 4 Make sure the cards are clean m Make sure they are stored in a dust free location 5 Make sure the print head is clean See the procedure for cleaning the print head in the Maintenance chapter of this manual 6 Check the ribbon m Make sure its position in the printer is correct m Make sure it is unrolling correctly 7 Check the print head m f horizontal white lines appear on the card some c
47. now automatically detect the USA por conmaded in your printer Connect your printer to your Computer easing USA cable Wail a few seconds before cennang on fo the nest alep on siaring the detector process F Step 4 USB setup Printer debe dion The setupwizaord hns successtully deiaded the printer and the USE port AOI connected w gt Evol Secunia Proceed to the mexi shep fo contioge the instalan on your computer Previous Cancel Step 5 replacing an existing driver This phase will occur only if an existing driver is detected on the system E ien 45 Exes Printer Denver There is already a Printer Oirer metalhead What do you want to do Replace Exicing criver by a new one C Add angh pilnter wih new name bul keep preide tiver version Devious Cmca SECURI Step 6 personalize your printer During this step you can set a personalized name to your printer Evolis Gaqunon The printer can also be defined as default printer You may then select the Evolis Color Profile In selected cases the color profile will provide color textu res very similar to what you will actually get Step 7 install driver and end of process Steg 7 Inehell Primer drer om yor compuber SrnberCirreer lestedeed popari he Printer Orrez has eters sucenes stall nsike When the installation process Is over print a test card to make sure your printer operates suitably You are now ready to
48. ntee is conditional upon compliance with these cleaning cycles cf Limited Evolis Warranty document Monochrome or color ribbon To install a monochrome or color ribbon in the print module proceed as follows 1 Open the P 2 Press the latch to printer cover a unlock the print head bracket and rotate it to the right until it is in vertical position If applicable remove the existing ribbon WANNA e T z LAY 3 Install the new ribbon in the position indicated in the diagram e oothed wheel toward the rear of the printer e Part including the new ribbon located on the right side card feeder 5 Reclose the printer cover 4 Lower the print head bracket and lock It SECURI F gt 010 Film for lamination _ The lamination unit includes components heated to high temperatures Make sure not to put your fingers inside the module Follow the safety instructions 1 Open the 2 If necessary carefully JP printer cover remove the existing O film taking care not to IN bend or twist it KS Introduce your y film holding it in both hands with the full spool in the right hand Hold the ribbon as indicated in the diagram 3 Insert the two cores about 1 inch onto the brackets 4 Position the film engaging it in the film guide provided for this purpose taking care not to damage it 5 Once the film is in place carefully push each core back gradually until it comes to a stop
49. oaded language BACKLIGHT Increasing or decreasing backlighting intensity 80 CONTRAST Increase or decrease in display contrast 80 NETWORK IP ADDRESS Display of the IP address of the machine MAC ADDRESS Display of machine s MAC address DHCP MODE On Activation of DHCP mode D faut Off Deactivation of the DHCP mode SUBNET MASK Display and modification of the Subnet Mask address GATEWAY Display and modification of the Gateway link address SECURICM 25 Error messages and diagnostics While the Evolis Securion printer was designed to work independently keeping your involvement to a minimum it may nevertheless be useful to become familiar with the main alert messages NEU e JEF Q Tic Lee LCD display and LED indicator The control panel includes two display lines and a LED type diode In general the messages break down into three categories E Equipment condition messages E Alert messages with no interruption of work E Alert messages with interruption of on going work Se These messages are given as follows through the display and the LED diode g L i UO gt Top line Messages linked to the printing station gt Bottom line Messages linked to the laminating station Fixed green LED Rated operation _ Flashing green LED Rated operation dialogue with the PC or work in progress 2 gt Fixed red LED Non blocking operator alert work continu
50. of the geographic area where you are located Securion is shipped in an original container specially designed to ensure that the product is protec ted against any risk of damage during shipment In the event of visible damage at the time of delivery do not hesitate to carry out all required steps as far as the shipper is concerned and immediately contact your Evolis dealer who will provide you with all necessary assistance Evolis has paid particular attention to the quality of this shipping material and we urge you to keep it in a clean dry space This packaging material will be required to return equipment J During the manufacturer s guarantee period returning material without the original Evolis packaging could cause you to lose the benefit of this guarantee The following parts are furnished with the Securion printer m Power supply unit VP ELECTRONIQUE type PAC150M E Main power cable m USB cable length 1 80 m Item A5017 m CD Rom Driver amp Documentation m CD Rom eMedia Card Designer badge design and personalization software including the utilization of an Excel source data base E Cleaning kit E Evolis Limited Guarantee document must be consulted In the absence of one of these components please contact your Evolis dealer Only use the power supply delivered with your Securion VP ELECTRONIQUE type PAC150M SECURION gt 08 Pre installation activation Before installing the printer please
51. omponents of the print head may be dirty or damaged m Clean the print head Consult the Maintenance chapter for more information m Sile probleme n est pas r solu apres nettoyage contactez votre revendeur pour un remplacement de la t te d impression SECURI M 45 Assistance o o o O o In order to assist you on a day to day basis Evolis has structured its customer service around a network of specialized partners g J Moreover to let you get answers to your questions 24 7 and 7 7 the Internet site www evolis com includes a number of elements linked to the day to day operation of your Securion Network of Evolis partners For any unresolved technical problem contact an Evolis dealer If you do not know of an Evolis dea ler go onto the www evolis com site and send us your request Evolis will give you the address of the Evolis dealer closest to you When you call an Evolis dealer you must be next to your computer and be prepared to provide the following information The type and serial number of your printer The type of configuration and the operating system you are using A description of the problem that has occurred A description of the steps you have taken to solve the problem Look for information on www evolis com If you need additional technical aid you will find a large amount of information relative to the utili zation and troubleshooting of the Evolis printers under the heading Support amp Servic
52. on the bottom of the bracket Then make sure the film moves freely without creasing 6 Reclose the printer cover Installation of the print ribbons and laminating films must be accompanied by adequate defining of the parameters of the print driver Please refer to the chapters on Properties of the Driver for additional details SECURION 11 Types of cards The Securion printer supports PVC cards varying in thickness between 0 25 mm 10 mil and 1 mm 40 mil For optimum quality these cards must comply with ISO Standard 7810 They are of a number of types m Blank cards m Magnetic stripe cards m Contact smart cards m Contactless smart cards m Smart cards and magnetic stripe Correct positioning of the magnetic stripe cards and of the contact smart cards in the feeder must be scrupulously observed Failure to comply with the direction of insertion would prevent the enco ding option from functioning In the most common procedure the cards are laminated after printing This operation requires that the card be heated to a high temperature which could cause it to be slightly deformed due to the heat and the stresses created by the film when it cools Evolis recommends the use of cards specially designed for lamination For more information contact your Evolis dealer who will provide guidance in making the choice Installation in the feeder The cards are installed in the feeder as follows 1 Open the 2 Remove the
53. rd makes it possible to gather certain technical data proper to your printer and to confirm that the printer is working properly We recommend that you print it as soon as you put your printer into service and keep It available Your dealer may ask you for it Printing of a test card 1 Wait until all the printing work is finished 2 Make sure there is a ribbon and a card in the printer 3 Go into the display menu by pressing one of the keys 4 Scroll through the menu choices using the key until you come to the SERVICE option then confirm by pressing OK 5 Scroll through the menu using the key until the TECH CARDS menu is displayed then confirm by pressing OK 6 The Auto Test option is displayed confirm by pressing OK to start printing the test card Interpretation of a test card ev Lis printer innovator Printer model Securion Mag Printer s n 07 100007500 Kit head n 400 66901594 D Firmware n of 10 Mac address 00 1 4 FD 00 00 01 IP address 192 168 1 1 Manual Evolis Gard Printer www evolis com info evolis com The test card allows you to validate the correct autonomous operation of your equipment not linked to a PC or any other computer m Correct printing of colors as well as single color black E Correct positioning of the ribbon in the print module E Correct removal of the protective film E Correct positioning of the protective film in the laminating module Additionally this test car
54. rol panel display 6 After about thirty seconds the Firmware has been transferred to the printer and the operation Is complete 7 The printer restarts and the message Restarting appears followed by the message Ready The update is complete and your equipment is ready to personalize your cards Never interrupt the transfer between the PC and the printer during the Important downloading phase by turning off the printer or the PC or disconnecting a cable The result would be the total inability to restart the printer If this ever occurs please contact your Evolis dealer who will replace your printer s pro cessor card Update the print driver The updating of the print driver is required in order to solve malfunction problems Prior to any update contact your Evolis dealer who can advise you as to whether or not it is appro priate to carry out this operation In order to download an update from the www evolis com en supservices access asp site a _ you must first have registered your product with Evolis see chapter Register your product in order to benefit from updates 1 Enter your login and password a page is displayed 2 Select the Securion printer model and the Drivers selection 3 Accept the download and register the file in a directory on your hard disk The file is stored in compressed zip file You must extract it and save it to a temporary directory 4 Then double click on the file Setup exe tha
55. rs now appears The principal tabs for defining parameters are Graphics Lamination Main and Tools Secunon Kersa Properties Graphic tab Choice of printing mode and of the associated ribbons Choice of the lamination mode Dual side parameter Adjustment of the ribbon parameters color black panel overlay panel options depend on the print ribbon selected Man GST Lamination Tok Ribbon l G panele dbhan YMCKOK 5 panele ebbon MCHC C Shall panels color ribban 1 2 YMICKO C 2 panes bban KO en C Monochrome K f m Hologran Ribbon Hj Sel moon Fenting Settings Print on the both sides fect D YMCKO E Front Side iT Laminate Laminate __ Black panel ch panel __Vamish Panel __Vamish Pane __Mare Options poe coke SECURI N me Seounon Reseau Properties Main Graphic Lamination Tals Lamination settings Laminate tye Full Clear Rese to factory settings Vamieh trent Full vamish Vanish back Full vamieh OK Canca ams 1amm 5 1 079 inchs P78 inchs Speed J 4 100C 180C Terpectue Cp lt _ _ _ fiw Dafina your custom estinga Setting name Lamination tab eine he varist sing Ful varas Choice of the type of film T Cortinvous boo Setting of lamination parameters e QTA 7 ines Personalized configuration Selection of the card eject mode SECURIT SECURIY M 20 Sequnon Reseau
56. rsuant to part 15 of the FCC Rules These limits are des igned to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio fre quency energy and If not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference s by one or more of the follo wing measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Use of a shielded cable is required to comply within Class B limits of Part 15 of FCC Rules Pursuant to Part 15 21 of the FCC Rules any changes or modifications to this equipment not expressly approved by Evolis Card Printer may cause harmful interference and void the FCC authorization to operate this equipment VCCI For Japan This i Cl B duct l antes ale CORES MMB ST ARRAS MEMS VCCI ome Voluntary Control Council for CHOC VPP ARBRE CORBIS SARR THATS Ce Interferenc
57. scape E Number of copies 1 Graphics tab m Type of ribbon 6 panel color ribbon YMCKOK m Dual side printing Click on Apply if you change a parameter then on OK to close each dialog box in succession When you are back to the main window MS Word Printing click on OK to start printing SECURION 22 Printer menus The Evolis Securion printer has an LCD display combined with a light emitting diode LED that allows the operator to visualize the operating condition of the equipment and to set the most com mon parameters Discovering the printer menu The Evolis Securion printer control panel has 3 groups m 1 LCD display with 2 lines of 16 characters each backlit for better rea dability of the information E 4 scroll keys to go through the menu confirming or deleting the choices m 1 two color LED green for normal operation red in a situation requiring Tat the attention of the operator evls In the standby mode after a short period following power on the control panel is in the following condition During operation the information display varies m Top line Status of the printing station E Bottom line Status of the lamination station m Fixed green diode On hold m Flashing green diode Transfer of data with PC or printing in progress m Fixed or flashing red diode posting of an alert or of an error message In the event of the intervention of the operator who activates the
58. serted the reading writing process has failed with more than one card it is recommended to manually start a printer cleaning process refer to the Cleaning chapter of this manual for the procedure to be followed ISO 7811 encoding standards Track no Field separator Track density Types of characters Number of characters Track 1 i 210 bpi Alphanumerical 19 ASCII 20 95 Track 2 Numerical ASCII 48 62 Track 3 210 bpi Numerical 107 ASCII 78 62 Bit s per inch Except the character Including the Start Stop and LRC characters The magnetic encoder generates these characters automatically SECURION 52 Tidi at Q ojii ALIVE Securion printers with a Smart Card Contact Station are called Securion Smart printers The wor king mode of a Securion Smart printer is identical to that of a Securion printer The Smart Card Contact Station of the Securion Smart enables the chips to be programmed to the ISO 7816 2 standards Location of the contact station The Contact Station is a module installed in the factory on Securion Smart printers The Contact Station is positioned over the path of the cards and before the print head To contact the Station the chip card is placed under it and is pushed up Hig 1 WAS a SS The programming sequence of a chip is always car F ried out before the card is printed Only use chip cards conform to ISO 7816 2 j Never print on the chip
59. software components the firmware and the print drivers The following chapters provide information on the ordinary maintenance operations that make it possible to keep your Evolis printer in perfect working order Replace the cleaning roller In the event your cleaning roller becomes less efficient despite regular maintenance it needs to be replaced in order to keep the print head from becoming clogged and ultimately permanently damaged See the chapter on Service the Cleaning Roller The cleaning roller is available as a consumable from your Evolis dealer SECURION 37 To replace the roller proceed as follows 1 Open the printer cover 2 Shift the print head bracket into vertical position then remove the print ribbon in the print module 3 Locate the cleaning roller 4 Install the new roller into the printer and release it from its seat making sure that It is correctly positioned In its seat 5 Replace the ribbon lower and lock the print head bracket in place 6 Close the cover The printer is ready for operation Replace the print head The print head is a sensitive component of your equipment It determines the print quality and its regu lar maintenance as well as the absence of dust in the Immediate environment guarantee its longevity However it can happen that this head needs to be replaced Evolis has designed a unique device that allows the user to proceed to this exchange without using any too
60. station in Celsius SPEED Indicates the scrolling speed of the card in the lamination station Parameter set in the print driver OFFSET IIndicates the time lag set in the print driver also called Offset Selection of maintenance cycles CLEANING gt PRINTER Starts after a cleaning card has been inserted into the feeder Starts the cleaning cycle of the entire card feeder system ADVANCE Reserved to a knowledgeable operator Makes it possible to start rotation of the feed rollers in order to do a complete manual maintenance Please watch out for rotating components Technical parameters SERVICE STATUS Pr Serial Display of printer serial number Printer Ttype Display of printer type Pr head ID Display of print head serial no Pr Firmware Display of pre loaded version of printer software Firmware Lam Firmware Display of pre loaded version of lamination station software Firmware Next Cleaning Counter showing the number of printable cards prior to the next mandatory cleaning cycle The displayed value is the number of cards before cleaning Failure to perform these cleaning cycles entails invalidation of the guarantee Technical parameters gt TECH Self Test Printing of a test card to check the correct operation of your Evolis Securion printer CARDS Printer Status Printing of a technical card with data pertaining to the printer DISPLAY LANGUAGE English Selection of English language Default Custom Selection of downl
61. t you have just extracted in order to start the downloading process For more details on procedures please consult the chapter on Installing the Print Driver SECURICN 41 In this chapter you will find out how to resolve certain problems that can arise while you are working Never use a metal tool or object to work on your equipment you run the risk of hurting f yourself or damaging all or part of the equipment When a card is jammed in the printing unit the message Mechanical error appears on the control panel display Work Is interrupted 1 Open the 2 Put the print head equipment a bracket ina cover vertical position and remove the ribbon 4 Replace the ribbon close the print head bracket making sure to lock it In place 3 Carefully remove the i jammed card ar N taking care gb ee Tt a not to oe KE the printer and its components 5 Close the equipment cover The printer resumes operation SECURION 42 Free a card jammed in the laminating unit When a card is jammed in the lamination unit the message Laminator Error appears on the control panel display Work is interrupted Do not turn off the unit this would lead to a loss of the printing jobs in progress that are stored in the printers memory 1 Open the 2 Press any key on equipment the control panel to cover eject the card into the box 3 Repeat this operation a number of times if necessary 4 If
62. tart button at the bottom left of the Windows task bar select Printers and Faxes m Select your printer with a left mouse click for example Evolis Securion m Click again using the right mouse key to bring up a menu and choose Define as default printer Other tabs gt General tab Windows information window that allows you to print a test page to monitor the computer printer communication gt Ports tab Windows control window that allows you to select the printing port and to validate use of the appropriate print driver The parameters displayed should be changed only by a person with advanced computer skills Color management tab This dialog box makes it possible to associate the printing with a specific color profile It is reserved for future use gt Security Sharing Advanced tabs Windows and Network parameters reserved for the system administrator of your computer system Do not change without prior approval SECURION 21 Card printing configuration in an office automation application A large number of Windows applications permit the printing of a document for example the tools of the Microsoft office suite MS Word MS Access MS Excel MS Power Point To help you familiarize yourself with formatting a card and setting the parameters for its formatting and printing we offer the following example Using Microsoft Word After first setting up the Evolis Securion default printer
63. the equipment cover The printer resumes operation The lamination module has detected a serious mechanical error Turn off your Securion printer and contact your dealer to get help Led The lamination module has detected an overheating problem a eVOLIS Turn off your Securion printer and contact your dealer to get The printer has detected a problem involving the feeding of cards into the lamination module Open the equipment cover Press any key on the control panel to activate ejection of the card to the hopper Never use a tool screwdriver pointed object to free the card This risks causing serious damage to the rollers and in particular to the unit s hot roller This type of damage would not be eligible for a request for coverage under the warranty help Once the card is free make sure the film is well positioned then close the printer cover The printer resumes operation The printer has detected a problem linked to the film in the lamination module Open the equipment cover Check the film position and if necessary replace it if you feel it is necessary Close the equipment cover The printer resumes operation SECURIPN 29 Dj ci In this chapter you will find all the information required to perform certain simple procedures that you may be asked to do by your Evolis dealer to provide you with the most effective assistance Print and interpret a test card The printing of a test ca
64. ul about defining the personalized parameters and do not hesitate to contact your Evolis dealer to get the necessary advice and assistance prior to any modification Wind at dri The Evolis Securion printer works on Microsoft Windows platforms Windows XP 2003 and Vista 32 and 64 bits Installation of the print driver To install your print driver you will need the CD Rom Drivers and Documentation shipped with your Securion printer D Please make sure the data cable is disconnected before starting this procedure ESS SS The installation program automatically selects the version to be installed in terms of your operating system SECURI MN 15 1 Load the DRIVERS amp DOCUMENTATIONS CD Rom in your CD drive 2 Wait a few seconds until the welcome screen asks you to choose your language If the CD Rom does not launch automatically double click on the setup exe file located in the DRIVERS directory on the CD Rom 3 Select your language by clicking on the appropriate flag 4 Click the Install Driver option to launch the setup program 5 Windows XP or 2003 platforms may require the Microsoft NET package to be installed Click OK to confirm and start this installation Evolissetup Setup he 7 To start EvolsSebup Setup dick OF To quit without instaling dick Cancel ao E Confirm your willing to proceed with the installation of Microsoft NET by clicking on Yes Microsoft HET Framework 1 1 Setup
65. will be conser ved Your Evolis printer should be recycled according to your local standards For more information please contact Evolis at into evolis com Thanks for choosing Evolis SECURI N to personalize and laminate your badges Using the latest printing and encoding technologies Evolis Securion offers its users both performance and quality Evolis Securion fully adapted to both small and mid volume runs combines simplicity of use and functional richness high quality printing and laminating magnetic encoding encoding of both contact and contactless smart cards The Evolis Genuine Product line of consumables linked to the printer was specifically developed and optimized to guarantee the highest quality of printing and laminating Using these consumables Increases the life span of your badges and of your Securion printer As for all Evolis products particular care has been used in writing this manual But if an error has still managed to slip into these pages without our wanting it please let us know by sending an e mail to infofdevolis com Evolis will then do everything in its power to correct the problem and give you complete satisfaction SN SECUR N C OIG eT me J KE Install the Evolis Securion printer Technology and benefits 0 0 aaaeeeaa 06 Initial approach aeneae aaar nearne 07 Install your printer aaaeeeaa eneren 08 Check the components shipped Connect the cables

Evolis Настанова користувача SECURION

Contents

Download Pdf Manuals

Related Search

Related Contents