Telstra T210 Telephone
Contents
1. Make sure all the connections are firmly in place Your telephone is now ready to use Depending on your wall socket you may need to use the telephone adaptor plug supplied 5 Wall mounting your Telstra T210 Getting to know your Telstra T210 Your TelstraT210 can be wall mounted by screwing directly onto a wall Liquid Crystal Display Displays dialed numbers and numbers stored in the memory Also displays call timer and other visible information Before you can wall mount your T210 you will need to fit the wall mounting bracket supplied 1 Locate the lugs and mount the wall bracket rovided onto the oles under the PA base unit as shown One touch Memories Preprogrammed for Telstra Call Waiting 3 Way Chat and Telstra Voice Assistant 2 Swing the wall bracket down to clip into the top hole Memory Button Allows you to dial up to ten numbers stored in the memory at the touch of two buttons Screwing onto a wall 1 Using the template on page 22 drill 2 holes Fnsure that you go nat 25mm deep using a 3mm drill drill into any hidden Call Indicator Light Flashes to indicate an wiring or pipes 2 Insert the wall plugsand incoming call Also insert a screw into each x y flashes when storing numbers using mute or hole Leave 2 3mm ia ra between the head of the 7 z3 setting the ringer screw and the wall Piet fy i 32. Follow all warnings and instructions marked on this product Do not use this product during an electrical storm as it is possible to get a shock Do not use this product when near water or when wet Make sure the line cords are protected from damage Keep the product away from heaters and away from sunlight Do not use this telephone near flammable gases or liquids Slots and openings in the cabinet are provided for ventilation to protect it from overheating Ensure these are not blocked or covered Do not open the unit There are no user serviceable parts inside Warranty conditions will not apply if the unit has been opened Unplug this unit before cleaning Do not use detergents or sprays To clean the outside plastic parts use only a damp cloth Do not push objects into ventilation openings This could cause an electrical shock General information This Unit complies with Australian Communications Authority Technical Standards If the quantity of ringing devices connected to the telephone line exceeds a REN of 3 it may result in some devices not ringing in response to an incoming call To check the REN of each device refer to the base label Product Warranty Telstra Guarantees your product for 12 months from date of purchase against any defect in materials or workmanship under conditions of normal use and service and subject to proof of the date of purchase being provided and subject to the conditions specified i
3. Position the product iii Store Button onto the screws A res ane i 4 Slide down to secure i change the ringer and g pitch volume Recall Button For use with Telstra Phone Features and PABX s Handset Hook This hook keeps the handset in place when the Redial Button T210 is wall mounted Volume Handsfree Mute Button AA a Revolve the handset catch on naf irons pets you talk tea en hin se to adjus ows you o someone in the ay volt The Mere EA the volume to hold a the same storing a number in the NOW DEADE LO TEST ON ENE NOO Wa during conversation room without memory when wall mounted f Handsfree over the the person O37 operation loudspeaker you are calling without lifting hearing you O the handset 7 Getting to know your Telstra T210 Explanation of display icons Main display This will display the phone number being dialled or the stored number in memory being dialled Phone icon This icon will display when the phone is in use Ringer off This will be displayed to remind you the ringer is set to off O Mute This will be displayed when the mute button is used Handsfree volume level This will be displayed when the speaker volume level on a handsfree call is changed Using your Telstra T210 Making and receiving calls To make a call 1 Lift the handset and wait for the dial tone 2 Dial the telephone number C The amp will be shown on the display to
4. amp Customer service D The defect was caused by an accident misuse abuse improper installation or operation lack of reasonable care unauthorised modification loss of parts tampering or attempted repair by a person not authorised by Telstra E The product has been damaged by lightning or a mains power surge Do you really need service Before calling for service under this warranty have you Checked that all cables are securely connected as detailed in the User Guide Referred to the User Guide to ensure that the features are being used correctly If you are trying to access a network service such as Call Waiting confirmed with your network provider that you have access to this feature If You Require Warranty Service To obtain service during the terms of this warranty Call the Product Information Line 1300 369 193 for advice and assistance on the repair of your product or contact us by E mail at tcpsupport techpac com After consulting our operators should it be deemed necessary to have the product serviced the operator will inform you of your nearest authorised service organisation and provide a Return Authority Number Please ensure that A You provide proof of the date of purchase B That your product is suitably packaged Preferably in original packaging C That you have included all components from the original purchase D That you provide details of the Return Authority Number
5. IMPORTANT Please retain this booklet with your sales receipt as proof of the date of purchase 22 COPYRIGHT 2003 Telstra Corporation Limited This work is copyright All rights reserved Other than for purposes and subject to conditions prescribed under the Copyright Act no part of it may in any form or by any means electronic mechanical photo copying microcopying scanning recording or otherwise be reproduced stored in a retrieval system or transmitted without prior permission from Telstra Corporation Limited ABN 33 051 775 556 Trade Mark of Telstra Corporation Limited Registered Trade Mark of Telstra Corporation Limited 1300 369 193 TecHelp is your guarantee of superior customer service for these products Your customer service options are e Product Information Line 1300 369 193 e 12 Month Product Warranty O 69 mm drill template hole dia 3mm O qelstra www telstra com
6. Line Cord Telephone Adaptor Plug Wall Mounting Bracket Memory Label Inthis guide Introduction to your Telstra T210 Telephone 1 In this guide 3 Installing your Telstra T210 4 Wall mounting your Telstra T210 5 Getting to know your Telstra T210 6 Using your Telstra T210 7 Making and receiving calls 8 Redial 8 Mute 9 Handsfree 10 To adjust ringer volume 11 To set the ringer pitch 11 Memories 12 To store a number in the memory 12 To dial a number in the memory 12 To delete stored numbers 13 To insert a pause in a memory number 13 One Touch memories 14 To store a one touch number 14 To dial a one touch number 15 Telstra Phone Features 16 Telstra Call Waiting 16 Telstra 3 Way Chat 17 Telstra Voice Assistant 18 Help 19 If the Telstra T210 will not operate 19 Important Safety Instructions 20 General Information 20 Product warranty amp Customer service 21 Wall mounting template 22 Installing your Telstra T210 Your Telstra T210 can be wall mounted by screwing directly onto a wall or can be fitted to a standard telephone wall mount plate Using the Handset Cord plug one end into the end of the Handset and the other end into the small socket at the end of the base Connect one end of the Telephone Line Cord into the socket at the bottom of the base Connect the other end of the Telephone Line Cord into the telephone wall socket
7. indicate that the phone is in use To receive a call 1 When the telephone rings the call indicator light will also flash to indicate that there is an incoming call Simply pick up the handset Redial To redial the last number called 1 Lift the handset Press the button The last number is displayed and then dialed You can also press the button when the handset is down to check the number first If this is correct press the button The number will be dialed automatically using Handsfree A redial number can be no longer than 32 digits If the telephone has been unplugged the last number dialed will not be saved 9 Using your Telstra T210 Mute When on a call you can talk to someone in the same room without your caller hearing To switch mute on and off 1 During a call press and release the button The caller will be put on hold You can now talk to someone in the room without your caller hearing you The display will flash HUTE to confirm mute is on 2 Press and release the button again to return to your callers Using your Telstra T210 10 Handsfree Operation The handsfree feature allows you to use the phone without picking up the handset giving you more freedom when you are speaking on the phone You can hear the caller s voice through the in built speaker To make a handsfree call 1 Press the button The handsfree light will come on and you will hear t
8. ber Your Telstra T210 will automatically dial the number using handsfree Telstra Phone Features Your Telstra T210 provides easy access to 3 popular Telstra Phone Features Call Waiting 3 Way Chat Telstra Voice Assistant Available most areas Telstra Call Waiting While you re on a call a Call Waiting tone initially two beeps following an alerting tone then two beeps every five seconds lets you know that there is a second incoming call Answering a waiting call 1 Press the Oin button The first call is put on hold and you can talk to the second caller Alternating between callers 2 Press the Olin button The second caller is now put on hold and you can talk to the first caller You may need to activate Calling Waiting on your telephone To turn Call Waiting on or off press the Telstra Voice Assistant button and follow the voice prompts 17 Telstra Phone Features Applicable usage charges and call costs apply Telstra 3 Way Chat If you are already ona call you can make another inquiry call to a third person after you put the first caller on hold If you wish you can then have a three way conversation conference The Call Waiting feature if turned on will not operate while you are holding a conference call To make an inquiry call while already ona call 1 Press the button and listen for dial tone 2 Dial the telephone number of the third person If the p
9. ch the number is stored The number is displayed and dialed automatically Numbers can be no longer than 18 digits long You can mix manual and memory dialing as required for example you can dial the area code 02 8304 from the memory and then complete the number manually 13 Using your Telstra T210 If any errors occur in the storing mode you will hear three short beeps then the product will return to talk mode If you unplug your Telstra T210 the numbers stored in the memory will be saved However the last number redial memory will be lost To delete stored numbers Lift the handset 1 Press the button Enter the memory location number 0 9 under which you have stored the number you wish to delete 2 Press the button You will hear a confirmation tone Replace the handset Alternatively any existing number stored in the memory can be overwritten by entering a new number under the same memory location Simply follow the instructions under the storing number section previously shown To insert a pause in a memory number Sometimes you may need to enter a pause when storing a number e g with an overseas number you may need to enter a pause after storing the international code 1 Press the button in the place where you want to enter a pause When you dial the number your T210 will automatically insert the pause where you stored it Using your Telstra T210 14 One Touch Memori
10. erson is busy or does not answer press the button to return to the first caller To establish a three way conversation 1 Press the Qn button All parties are now connected To end a three way conversation 1 Press the Ohlin button This places the last party on hold and the original call remains connected The user can then toggle between callers using the m1 AA button Telstra Phone Features 18 Telstra Voice Assistant Telstra Voice Assistant is designed to make using Telstra s phone features easier and provide you with information about them There s no need to remember special codes to turn your phone features on or off just Jelstra press the Orin button and tell your phone what to do Help If you have any difficulty using your Telstra T210 this section provides solutions to the most common problems No dial tone Make sure the telephone line cord is plugged into the telephone socket at the back of the unit and that the telephone line cord is connected to your wall socket Check that no other extension is in use Phone does not ring Check that the ringer is not switched off on your T210 Unplug the Telstra T210 and connect a telephone that is known to be working Check that no other connected phones are off the hook Check whether you have too many phone extensions in your home or office Help 20 Important safety instructions Read and understand all instructions
11. es The Telstra T210 comes with 3 Telstra Phone Features preprogrammed into the M1 M2 and M3 buttons Should you wish these can be overwritten with your own frequently dialed numbers To store a One Touch number 1 Lift the handset 2 Press the button The display will show Lace 3 Press the network feature button under which you want to store the number The display will show e g Lcic cli if you want to store under Call Waiting button or M1 4 Enter the telephone number you want to store including the area code if applicable 5 Press the button You will hear a confirmation tone and the display will show SAVED 6 Replace the handset For mor information on these features please call 13 2200 Please note that the number can be no longer than 18 digits Whilst storing a number in the memory you can cancel the operation by replacing the handset on the cradle If you delete a number in any of the One Touch memories the key automatically reverts to its factory programmed Telstra Network Feature A blank memory label is provided to note your frequently used numbers 15 Using your Telstra T210 To dial a One Touch number 1 Lift the handset and wait for the dial tone 2 Press the memory location number under which the number is stored The number is dialled automatically You can also dial a One Touch number when the handset is down Simple press the memory location num
12. he dial tone The display will also show the volume level 2 Dial the telephone number You can now talk to your caller through the microphone or pick up the handset to speak to your caller privately To receive a call using Handsfree 1 Press the dE button when the phone rings To change the volume on a handsfree call You can adjust the speaker volume when you are on a handsfree call 1 Press the button The volume level will be shown on the display There are 5 levels to choose from It is pre set to the mid range level 2 Press the button to move up and down each level Important Your Telstra T210 is specially designed to operate without the need of a mains power supply It is therefore necessary to make your first call via the handset This call should last at least 1 minute Subsequent calls can now be made using the handset or Handsfree feature You can swap between the handset and handsfree during a call If using the handset press the gt button and replace the handset If using handsfree lift the handset to talk privately You can only change the volume of a call when using handsfree 11 Using your Telstra T210 If the ringer is set to OFF the call indicator light will still flash to indicate somebody is calling you The display will show RIHGER OFF when you lift the handset or use handsfree To adjust the ringer volume There are 3 volume settings to choose fro
13. m HIGH LOW or OFF The default setting is HIGH 1 Lift the handset and press the button 2 Press the button The display will show BELL LEVEL HI 3 Press either for HIGH O for LOW or B for OFF 4 Press the button Your selected setting will be displayed You will hear a confirmation tone and the display will show SAVED 5 Replace the handset To set the ringer pitch The ringer pitch can be set to High or Low The default setting is High 1 Lift the handset and press the button 2 Press the button The display will show BELL Pitch HI 3 Press either for HIGH or for Low 4 Press the Store button You will hear a confirmation tone and the display will show 5A ET 5 Replace the handset Using your Telstra T210 12 Memories You can store 10 telephone numbers in the memories To store a number in the memory 1 Lift the handset 2 Press the button 3 Press the memory location number between 0 and 9 under which you want to store the number The display shows e g Liu if you want to store in location 8 4 Enter the telephone number you want to store including the area code if applicable 5 Press the button You will hear a confirmation tone and the display will show SAVED 6 Replace the handset To dial a number in memory Lift the handset and wait for dial tone 1 Press the button Enter the memory location number between 0 and 9 under whi
14. n this user agreement The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the product that the consumer has under the Trade Practices Act and similar State and Territory laws Warranty Service Conditions Subject to your statutory rights referred to above Telstra expressly limits its liability with respect to its products to the person who purchases the Product from the Telstra authorised retailer Subject to your statutory rights referred to above Telstra expressly limits its liability with respect to its products to whichever is the lowest amount out of A The cost of having the goods repaired B The cost of replacing the goods or C The cost of obtaining equivalent goods Subject to your statutory rights referred to above in the event of the goods requiring service under warranty the owner is responsible for the cost of transportation to the authorised service organisation Whilst in transit the goods are at the owner s risk Subject to your statutory rights referred to above should the goods be found to be in sound working order by the authorised service organisation the owner may be charged a service fee Subject to your statutory rights referred to above the goods will not be eligible for service under this warranty if A Proof of date of purchase cannot be provided B The goods are not branded Telstra C The goods have been rented to another person Product warranty
15. qelstra Telstra T210 Telephone User If you have any problems with your phone firstly refer to the Help section of this User Guide or call the TecHelp line on 1300 369 193 TecHelp Introduction Liquid crystal display Displays dialed numbers and numbers stored in the memory Handsfree operation Allows you to hold a conversation over the loudspeaker without lifting the handset 3 One Touch memories Preprogrammed with three Telstra Phone Features which can be overwritten with frequently used numbers 10 memories Allows two touch access to a further 10 most frequently used numbers Call indicator light Visuaally alerts you to an incoming call Last number redial Redials the last number you dialled Adjustable ringer volume and pitch The ringer volume level and pitch can be adjusted to levels appropriate for you Wall mountable Can be easily mounted on the wall using the wall mounting bracket supplied 12 month warranty This User Guide provides you with the information you need to get the most from your phone Before you make your first call you will need to set up your phone Follow the simple instructions on the next few pages Need help If you have any problems setting up or using your Telstra T210 please contact the TecHelp line on 1300 369 193 Alternatively you may find the answer in Help at the back of this guide Got everything Telstra T210 Telephone Telephone
Download Pdf Manuals
Related Search