USER MANUAL - Mega Systems
Contents
1. 220V cr D DMX 512 Connection The fixture is equipped with Neutrik NC3FXX HD and NC3MXX HD IP 67 3 pin XLR Sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for RS 485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another DMX input DMX output 1 Shield 2 Signal 3 Signal Q Caution At the last fixture the DMX signal needs to be terminated with a terminator Solder a 120 Ohm re sistor between the and the signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run Pre manufactured terminator plugs are available for purchase from your Mega Lite dealer P DMX T Display Menu Mega Lite Indi Par DAX To Set the DMX Start Channel press and hold the Mode Use the A or Y to se lect the desired DMX Start Channel and press Mode to confirm your setting To set the desired operational channel mode press and hold Mode Use the A or V to select the desired DMX profile operational mode from 3 4 or 6 and press Enter to confirm your setting Note Operational mode are located on Page 8 of the manual This function will give you access to the Preprogramed Chases Press and hold Mode Usethe A or Y to select the programed chase press Mode to confirm your setting Use the A or Y to select the desired speed of the Chase from 1 to 15 press Mode to confi2. MEGAG IND PAR RW300 USER MANUAL Table of Contents o ALL E ri BO O o EOI A Main Power Connect aa DMX 512 COnnectiOn aa Mam Control MENU BE Bi Gai AA FAM KUA AA AA MAPA PER GP RAPPER Cleaning 3 Mamtenance Sieg E E A IS AA tenguin Check that the unit has not been damaged during transport Read all cautions and warnings prior to operation of this equipment Protection Against Fire Fire Maintain a minimum of 1 foot distance from any type of flame Replace fuse only with the specified type and rating Do Not install the unit to close to a heat source Make sure cable are properly secured Maximum surface operating temperature 140 dada Protection Against Electrical Shock AN Electrical Disconnect power before servicing For connection to main power supply proceed to page 5 This unit must be earthed electronically grounded This unit is IP 65 rated do not submerge unit into water UNG Protection Against Mechanical Hazards 1 Use safety chain when hanging unit ak 2 Use quality clamps or bolts when positioning unit 3 Do not open unit while it is on risk of electrical shock Mechanical Technical Information Part Numbers 7300 Indi Par RW300 Mechanical Specifications DMX Connectors Neutrik 3 pin XLR NC3FXX HD D and NC3MXX HD D 12 IP 67 connectors in and out Power connection Weather Sealed Neutrik True Power NAC3FX W Connections to Nema 5 15 adapter in
3. cluded Weather Covers for unused connections included Thermal Maximum ambient temperature 104 Maximum surface temperature 140 9 5 Fastening System Single Yoke Display Digital 13 12 Lens Angle 15 Ip Rating IP65 Fixture Packaging Size 13 12 x 11 85 x 5 75 Size 13 5 x 11 25 x 7 5 Weight Ib Weight 8 75lb Electrical Specifications LED Quantity 12 Tri Color LED s Red Green Blue Power Input Voltage 110V 240 50 60 Hz LED Watts 3W Ballast Electronic auto switching LED Lifetime 40 to 80 thousand hours average Power Consumption Watts 57 Amps 75 Refresh Rate 6000 Hz Wireless DMX Wireless solutions built in receiver Battery Information Charging Cycles 300 Battery Life at Full 8Hr average Battery Life Colors 12Hr average Control amp Programming Protocol DMX 512 DMX Modes Mode 3 Channels R G B Mode 4 Channels Dimmer R G B Mode 6 Channels Dimmer R G B Strobe Macro Control Options Display preset setting Master Slave Function Main Power Connection Caution T Do not connect fixture to a dimmer system 2 This unit has Auto switching power supply It will respond to 110V or 220V automatically This unit must be earthed electronically grounded The occupation of the connection cable is as follows This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz Cable USA Cable EU 110V
4. edure and must be accompanied by a copy of the original invoice and Return Authorization Number given by MSI Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer MEGA SYSTEMS INC makes no warranties express or implied with respect to any product and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose Mega Systems shall not be liable for any indirect inci dental or consequential damage including lost profit sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product regardless of the form of action weather in contract tort including negligence strict liability or otherwise and weather or not such damage was foreseen or unforeseen Warranty is void if the product is misused damaged modified in any way or for unauthorized repairs or parts This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mega Lite 5718 Kenwick St San Antonio TX 78238 Ph 210 684 2600 Fax 210 855 6279 www mega lite com info mega lite com
5. ing the device or part of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing fixation and installation spots ceiling suspension trussing 3 The electronic power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed Note There is no serviceable parts inside the device except for the LED s Maintenance and service operations are to be carried out by authorized dealers Replacing the fuse Only replace the fuse with the same type and rating Replacing the power cable If the power cable of this device becomes damaged it has to be replaced by author ized dealers or trained professional only Should you have further questions please contact your dealer Parts List Warranty Information Warranty Conditions Unless otherwise stated in writing your product is covered by a one year parts and labor limited warranty LEDs are not guaranteed to match in color temperature or output It is the owner s responsibility to furnish receipts or invoices for verification of purchase date and reseller or distributor If purchase date cannot be provided date of manufacture will be used to determine warranty period Goods returned under warranty must follow the proper authorization proc
6. or Blue LED Intensit 0 255 4Ch CT Dir Diner otto Eur 0 255 6Ch Eimer lo Dimar oto Fur 0 255 Fe coer at Le ely os 60 79 Aqua 100 119 Orange 120 139 Rigging the fixture Caution 1 The installations must be carried out by an authorized dealer or trained professional 2 Unit may cause severe injures if you have doubts concerning the safety do not install 3 Unit is to be 24inches away from flammable materials decoration material 4 Use high quality installation equipment to hang unit When rigging a unit it is very important that you follow common safety procedures Rigging requires extensive experi ence including but not limited to calculating working loads material being used and periodic safety inspections If you lack these qualifications do not attempt the installation yourself instead use a professional structural rigger When rigging the unit always be secured with a secondary safety attachment The installation location of the fixture has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming Installation should be checked at least one time a year by a skilled person Cleaning and Maintenance Installation Maintenance The operator has to make sure that the unit is operating safely and has the installa tions and electronics checked by an expert every year The following points have to be considered during the inspection 1 All screws used for install
7. rm This function will give you access to set a color via display Press and hold Mode Use the A or V to select the desired color Press Mode use the A or V to se lect intensity from O to 255 You can repeat this process to get any color combi nation Note once color is set you can power up and the last color set will automatically come on This function will give you access to the LED Dimming curves Press and hold Mode Usethe A or Y to select the LED dimming operational curve from O that will not have a dimming time to 3 that will have the longest dimming time press Mode to confirm your setting Batter This function will give you access to check on the percentage of battery power Wireless Set To Set the Wireless DMX press and hold the Mode Use the A or Y to select the wireless DMX on or off Press the Function button from your Mega Air wireless transmitter Set the display on your fixture to the DMX screen and set the DMX start channel to the desired channel note If fixture is not connecting try to unlink transmitter by pressing and holding the function button on the transmitter until the connection button starts to flash Then press the function button quickly to reconnect On Slave Mode the fixture will copy the functions on the Master unit note must be connected via DMX cable Indi Par RW300 DMX Profile 3Ch DMX Chanel LED Color Red LED intensit 0 255 LED Color Green LED Intensit 0 255 LED Col
Download Pdf Manuals
Related Search