EAGLE™ 2.2 User Manual - Rainforest Automation
Contents
1. From Meter Notice that there is a gear icon in the lower right corner Clicking this will bring up the Advanced Settings page Information about the Advanced Settings page can be found at the end of this section 20 Www rainforestautomation com rainforest EAGLE automation User Manual Internet Sub Page Expanding the Internet status bar on the Settings page brings up the Internet sub page ntemet Connected Pea Meter MR History IP Address Ethernet MAC D lt Messages 1 Settings This sub page provides information about the connection between your EAGLE and the internet Cloud Sub Page Expanding the Cloud status bar on the Settings page brings up the Cloud sub page cloud Not Configured Cloud ID URL Last Upload bX Messages Set Cloud ili Settings This sub page is used to configure your EAGLE to stream your real time smart meter data to an internet cloud service Select the cloud service you want from the Cloud List drop down menu for Provider and click the Set Cloud button at the bottom right To complete your connection to the Cloud Service you will also have set up an account with them See the Connecting to a Cloud Service section for details If you wish to stream your data to a destination that is not shown on the Cloud List you can add a new entry to the Cloud List by clicking the add cloud icon You will be prompted for Provider service na2. To get to the Gateway page from any other page click the word Gateway in the command bar at the top of the page i rainforest My Account Gateway Log Out The first time you log in you will sent to the Gateway page At this point you will not yet have a gateway registered to your Cloud Account so you will be prompted Please add a device Gateway Please add a device New Gateway Click the blue New Gateway bar to go to the Add New Gateway page Enter the Cloud ID and the Install Code for your EAGLE These numbers can be found on the Information Label that is on the underside of the unit Add New Gateway Where can find Cloud ID amp Install Code 6 Digit CloudiD eg 000123 MMM MAC 0000 0000 0000 0000 install Code 0000 0000 0000 0000 I m not a robot FECES ZigBee N27879 Certified product Model RFA Z109 EAGLE Add Cancel Click the blue Add bar This will bring you back to the Gateway page Now you will see that your EAGLE is listed Rainforest Automation Inc FCC ID YCXRFA Z109 IC 8919A RFAZ109 Made in the USA www rainforestautomation com Ol 28 rainforest o ma ti on automation My Account Gateway EAGLE 000000 1 EAGLE User Manual Log Out You can additional EAGLE s to the list on the Gateway page by clicking the blue New Gateway bar and repeating the process Beside each EAGLE in the list there are
3. Overview Realtime Monitor Primary Residence The Rainforest Eagle is able to get real time data from participating Smart Meters No electrician is required for installation t WOTK To Purchase an Eagle already have a Rainforest Eagle Enter 6 digit CloudfiD 000000 Connect my Eagle Www rainforestautomation com 35 rainforest EAGLE automation User Manual lt Overview Real Time Device lt Overview Real Time Device Rainforest EAGLE Rainforest EAGLE Status Never Connected Status O You will see the current status of your se a EAGLE ee gt a If it is not shown as connected refresh the ml page after a few minutes 6 Digit Cloud ID 678948 6 Digit Cloud ID 000603 Update Cloud ID Update Cloud ID View your BlueDot data Click the Energy link in the web page header or the My Home link in the mobile app to see your real time projected and historical data lt Overview Energy Use ee Vacation Home wa Primary Residence Teday s Power Use Viatts Current Power Use men 44 an hour 3 132 Watts Updated S F gs gt F F Fa s 3 mints 6 seconds ago 7 Current Billing Period Messages id Projected S260 1 165 kWh As olid S165 750 KWh W Energy Use BH Home Journal Real Time Devices Past Week TT Da Pre 36 Www rainforestautomation com rainforest EAGLE automation User Manual Connecting Locally to your EAGLE If t
4. area graph for the following time periods o Hour shows the last 60 minutes with samples every 8 seconds o Day shows the last 24 hours with samples every 15 minutes o Week shows the last 7 days with samples every 15 minutes e Consumption shown below displays the total historical usage in kilowatt hours as a bar graph for the following time periods o Day shows the last 24 hours each bar is consumption for an hour o Week shows the last 7 days each bar is consumption for a day o Month shows the last 31 days each bar is consumption for a day o Year shows the last 12 months each bar is consumption for a month 1 50 Meter lala History r inl Lill 4 PM 6 PM SPM 10PM 124M 24M 4AM 64M 8AM 104M 12PM 2PM 4 PM consumption DCI GS 20141198 16 Www rainforestautomation com rainforest EAGLE automation User Manual You can switch between the graph time periods using the buttons under the graph If you hover the cursor over the graph a box will pop up with the detailed info for the data point at that spot on the graph You can zoom in to an area on the graph by clicking on a spot and dragging the mouse This will show a highlighted area which will rescale the x axis to fill the graph when you let go of the mouse button Beneath the bottom right hand corner of the graph is the download symbol Click this to download the raw data from the EAGLE database for the time period of the current g
5. as a self scaling arc graph the start and end of the scale are shown in small grey numbers beneath either end of the arc The real time consumption rate is shown as a number under the arc e Meter Reading shown below displays the raw total accumulated electricity usage reading in kilowatt hours from the smart meter This usage is labeled 14 Www rainforestautomation com rainforest EAGLE automation User Manual From Grid If you are generating your own electricity for instance with solar panels and have a Net Metering agreement with your utility then there may be times when you will be producing more energy than you are using and electricity will flow out to the grid The total of this surplus electricity you have delivered out to the grid is labeled To Grid Meter Reading em Meter Set by User Price per kWh An H istory From Grid 80342 626 kWh oog To Grid 0 000 kWh be 91 36 D lt Messages lt Settings You can switch between these two modes by clicking the Current Usage and Meter Reading buttons above the usage display To the right of the usage display is pricing information This shows the price of electricity that is currently in effect This is labeled Price per kWh and is usually shown in cents Above the price is the Rate Label This usually reads Set by User and indicates the current price has been set manually by you see the Settings button section It is al
6. network Entering this IP address into your browser will connect you to the EAGLE Www rainforestautomation com 39 rainforest EAGLE automation User Manual Symptom The Web Viewer just shows Loading and is unable to get data f Ensure that you have contacted your utility and they have loaded your meter with your device information and the meter is ready to communicate with the EAGLE g Check that the EAGLE ZigBee light is on continuously and is not flashing If the light is flashing try moving the EAGLE closer to the meter If this does not cause the light to go from flashing to continuously on then the EAGLE may need to be disconnected from the meter and be re provisioned by your utility Technical Support Contact us at http support rainforestautomation com 40 Www rainforestautomation com
7. 5 17 05 A HW Custom FW Multiplier I H sto ry ZB Divisor RFA ID Set lt Messages Factory Reset Check Update Allow Remote Management Tht E Enable Security o Settings This page provides information about your EAGLE hardware and firmware and lets you set some network configuration options Your EAGLE comes preconfigured to allow remote device management including software updates using Secure Shell SSH and Virtual Private Network VPN If you prefer not to allow external connections to your device you can disable this function by un checking the box next to Allow Remote Management The Check Update button will look for software updates for your EAGLE the Allow Remote Management box must be checked for this to work If new software is found you will see this pop up New version of EAGLE firmware is available Do you wish to update If you click OK your EAGLE will download and install the update after which it will automatically reboot You can also use the dropdown menu next to the Check Update button to have your EAGLE check and notify you of updates automatically The Enable Security check box in the lower left corner of the page must be checked to allow access to your EAGLE through rainforestcloud com If this check box is not checked then your EAGLE can only communicate through your local network For more information about connecting locally se
8. A rainforest automation EAGLE Energy Access Gateway Link to Ethernet User Manual Version 2 2 2 June 2015 www rainforestautomation com rainforest EAGLE 6 mati o n User Manual Copyright 2015 by RAINFOREST AUTOMATION INC RFA All rights reserved No part of this manual may be reproduced or transmitted in any from without the expressed written permission of RFA Under copyright law this manual or the software described within cannot be copied in whole or part without the written consent of the manufacturer except in the normal use of the software to make a backup copy The same proprietary and copyright notices must be affixed to any permitted copies as were affixed to the original This exception does not allow copies to be made for others whether or not sold but all of the material purchased with all backup copies can be sold given or loaned to another person Under the law copying includes translating into another language or format Rainforest Automation may have patents patent applications trademarks copyrights or other intellectual property rights covering subject matter in this document Except as expressly provided in any written license agreement from Rainforest Automation the furnishing of this document does not give you any license to these patents trademarks copyrights or other intellectual property Trademarks Third party brands and company names mentioned herein may be tr
9. I 18 Settings Button 19 EAGLES root 20 Memel U Pagnini 21 Cloud Sub Page EE 21 omat MeeFolb P4le i A E A AERE 22 Advanced Settings Page 23 Using YOUR Cloud TCC OUI pionieri 25 reatino a CUT ACCOU Eea E ete atatetateteseenstenates 25 Managing your Gateway List i 27 Managmg your Cloud ACCOUN seseina eaa E AEREE ENEE 28 Connecting to a Cloud Service ccccsccsesscecessecensseeenssecenssecenseecenseeneaseeoeasseoessesnens 30 Connecting to Wattvision 31 Connecting to BIUC6DOt m i 34 Connecting Locally 16 VOUrEAGLE N iinriraiiennnailnaaiania nn 37 Froubleshooting GUIDE iii ani pair ni aiar alii dedi dalai 39 I CCHAICaFSUPPO zine se tiratori 40 Www rainforestautomation com rainforest EAGLE o matio User Manual Regulatory information FCC Notices This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment FCC IC RF Exposure Statement This equipment complies with FCC and Industry Canada radiation exposure limits set forth for an uncontrolled environment The antenna s used for t
10. ademarks and or registered trademarks of their respective companies and are the sole property of their respective manufacturers Notice The author s assumes no responsibility for any errors or omissions that may appear in this document nor does it make a commitment to update the information contained herein Www rainforestautomation com rainforest EAGLE A User Manual EAGLE Energy Access Gateway Link to Ethernet RFA Z109 Version 2 2 2 User Manual Table of Contents Regulatory MIOrMalON iii inni 4 QUICKSEeIUP i O 5 Step 1 Prerequisite software and hardware 5 Step 2 Provision the EAGLEMM cccccccccccseeeeceeececeeeeseeeeeseesesseeeessaeeesseeessaeeesaees 5 Step 3 Power UD ING EAGLE Mac ei eo 5 SICA Greate VOU ClO ACCOUNT ccccssctecscacceececasececceesercacsexcesacesacrecesenccasssecceaciconseecoe 6 ole CONNEC TO YOUU EACLE T sereni E E E e ENEN 7 Features of Your ee lille scien clapton sinu de silecidcibe se elcaetel een eieaise tanieesion ens 9 Introduction to Your EAGLE aaa 10 EAGLE SAUS EED LIGRIS eri 11 EAGLE Hardware POftS snsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn dana 12 Understanding the Information Label cccsscccseseeeseeeeseeeeseeeeseeeeneeeeneeeeseeeenenes 13 Web Viewer PUNCHONS scriniiornizininin nani pin inni ciniiininininlaaiipinisipiriiienti 14 NCeIeFBUi l n 14 gic a ier hr er ee er ree 16 VESPR
11. at says Your account has been activated Click the word here to go to the Login page Your account has been activated 6 Www rainforestautomation com rainforest EAGLE automation User Manual Step 5 Connect to your EAGLE Enter your email address and password and click the blue Submit bar to log in to your Cloud Account Login user email com Forgot Password Register You will see a page that says Please add a device Click the blue New Gateway bar Gateway Please add a device New Gateway This sends you to the Add New Gateway page Enter the Cloud ID and the Install Code for your EAGLE These numbers can be found on the Information Label that is on the underside of the unit Add New Gateway Where can find Cloud ID amp Install Code 6 Digit CloudiD eg 000123 AA A AT MAC 0000 0000 0000 0000 stati Gode 0000 0000 0000 0000 PU I m not a robot ee Fe C co Add Certified product Model RFA Z109 EAGLE Rainforest Automation Inc FCC ID YCXRFA Z109 Cancel IC 8919A RFAZ109 Made in the USA Click the blue Add bar This will bring up the Gateway page Www rainforestautomation com rainforest EAGLE automation User Manual Your EAGLE should be listed Click on the connect icon next to the listing rainforest My Account Gateway Log Out Gateway EAGLE 000000 x This will connect you to your EAGLE and you shou
12. come to BlueDot Click the brown Continue button in the email 34 www rainforestautomation com rainforest automation EAGLE User Manual This will send you to your browser and to the Signup Completion page Fill out the form and click the Complete Signup button at the bottom of the page Then you will go to the Home Dashboard page Home Dashboard Primary Residence w nin 4 ii ivi ST SR ey Weare nor currentiy Getting er yr Click the blue Get a Realtime Monitor button Use the Home Journal You will see the Add a Device page which will give you the instructions on how to set up the EAGLE Upload Server which you have already done All you need to do is enter your EAGLE Cloud ID at the bottom of the page and click the blue Add EAGLE button Get a Realtime Monitor Using the BlueDot App You can also use one of the BlueDot mobile apps BlueDot by weMonitor iOS app or BlueDot Android app to get your BlueDot account and get connected seeeo Verizon T 1 01 PM 1O 78 BlueDot Save Energy Save Money e _ osi amp Tell me How it Works WQ Register for Free S Login to my Account Dm Overview Primary Residence Connect a Realtime Monitor Messages Home Journal My Home Contact Us My Profile Logout esoe Fido 3G 7 56 PM lt BlueDot Sign Up me email com 12345 r agree to the Terms amp Conditions lt
13. e the Connecting Locally to your EAGLE section The Multiplier and Divisor fields on the right of the page are primarily for commercial meters and should not be changed www rainforestautomation com 23 24 rainforest EAGLE automation User Manual The Factory Reset button on the left of the page should be used with caution It reboots the EAGLE terminates the smart meter connection clears all of the history data and sets all options to original factory settings The meter will not talk to the EAGLE again until it is re provisioned by the utility This function should only be used if absolutely required Www rainforestautomation com rainforest EAGLE automation User Manual Using your Cloud Account Your Cloud Account on rainforestcloud com makes it easy for you to connect to your EAGLE from anywhere It also allows you to manage access to more than one EAGLE from a single account Creating a Cloud Account To create a Cloud Account use your web browser to go to rainforestcloud com You will see the Rainforest Login page rainforest g U t 00 Mmoe t I O A Login Click on the word Register in the lower right corner This will take you to the Registration page rainforest a u t o m a t i o n Fill in the registration information Required You must supply a valid email address and a password The rest of the information is optional Optional Selec
14. ecurity configuration Enter the Cloud ID and Install Code for your EAGLE Symptom Your web browser cannot find the EAGLE locally a Check that the EAGLE power light is on If not make sure the power cord is plugged in firmly in the back and the adapter is plugged into the wall outlet you can also try another outlet Check that the EAGLE Ethernet light is on continuously and is not flashing If the light is not on ensure that the Ethernet cable is plugged in solidly to both the router and the EAGLE Check that router is turned on and that the light on router port indicates that the EAGLE is connected If the EAGLE Ethernet light is flashing this means that the EAGLE did not get an IP address from the router Make sure that the EAGLE is connected to a router and not just a switch Try unplugging the power cord of your EAGLE and plugging it back in again after 10 seconds This will reset your EAGLE Make sure the Ethernet light comes on and goes from flashing to always on Make sure that your computer is plugged into the same router as the EAGLE If you are on a mobile device make sure you are connected to the same WiFi network that the EAGLE is plugged into If you are not using an Apple computer check that you have installed mDNS or Bonjour for windows htip support apple com kb DL999 If none of the above work find the IP address of the EAGLE by logging into your router and locating the EAGLE on the
15. er 00 04 30 al I History Wattvision Inc w Mever gt lt Messages 2 Set Cloud 1 Settings Get a Wattvision account Note that Wattvision uses your Google account for sign in If you do not have a Google account go to the Google home page www google com and click the Sign in button in the top right corner Then click the red SIGN UP button in the top right corner and follow the directions 1 Open another window in your web browser and go to www wattvision com partners rainforest Click on the big green Sign in wattvision How It Works Residential Commercial About Contact to Wattvision button at the bottom of the page Rainforest Wattvision Follow the steps below to complete pairing of your Rainforest sensor and Wattvision Sign In to Wattvision 2 You will see the Google sign in page Enter your email and password and click the blue Sign in button I Lig tas I I Gor Ig I I I I I I Accounts i wattision uses Google Accounts for Sign In Sign in Email I Googe is not afiHiated with the contents of wettvlakoan or ite awmners Ii yo SH im Google wall share your mal I email address with wallvision bui not your password or any oihar personal information abc def xyz l I Pasevrord I I I I I I I I I I I I I I I I I I I I wabtvishon may ues your email address to perconalize youl exgerence on thew webete I I I I I I I I I I I Www rainforestautoma
16. es 17 Settings Not Connected CH 16 il v 17 Settings 00 04 30 j None Q EE HT Settings Now you can select the Cloud Service you want from the drop down menu for Provider To set your selection click the Set Cloud button To complete your connection to the Cloud Service you will have set up an account with the Cloud Service and you will have to indicate that data will be coming from a Rainforest EAGLE device You will also have to provide your 6 digit EAGLE Cloud ID which is shown right above the drop down menu on this sub page Your Cloud ID is also printed in the middle of the Information Label that is on the underside of your EAGLE In addition to the Cloud Services found in the drop down menu you can also select Manual This will cause a new Enter URL field to appear You can enter the internet address to any server that understands the EAGLE Uploader RESTful interface This interface is documented in the EAGLE Uploader API Manual which can be found on our Developer Portal http rainforestautomation com developer In the following sections you will find detailed directions for connecting to specific Cloud Services Www rainforestautomation com rainforest EAGLE o mation User Manual Connecting to Wattvision Set up the EAGLE upload server 1 In the Cloud sub page select Wattvision from the drop down menu for Provider 2 Click the Set Cloud button Pa Met
17. he Enable Security check box in the lower left corner of the Advanced Settings page is not checked then your EAGLE can only communicate through your local network You can do this using a web browser The computer running the web browser must be connected to the same router as the EAGLE and the computer must also be running multicast Domain Name System mDNS which is known as Bonjour on Apple computers MDNS may be already installed on your computer as many printers and Apple s iTunes use this protocol If you need to manually install mDNS on your Windows PC you can find instructions at htip support apple com kb DL999 The Local Web Address of your EAGLE can be found on the Information Label that is on the underside of the unit ZigBee mac 0015 8D00 001A B9D8 in CODD 5FE9 7384 1CBC eames 5902 Web iii 000204 Add ress FECES LigBee N27879 Certified product Model RFA Z109 EAGLE Rainforest Automation Inc FCC ID YCXRFA Z109 IC 8919A RFAZ109 Made In Canada Simply type this address into the URL field of your web browser and connect When your web browser connects to the EAGLE you should see the Web Viewer You can then click the Settings button expand the EAGLE status bar and click the gear icon in the lower right corner to get to the Advanced Settings page Now you can check the Enable Security box in the bottom left corner This will enable you to access your EAGLE from rainforestclo
18. his equipment must be installed to provide a separation distance of at least 8 inches 20cm from all persons ICES 003 Compliance This Class B digital apparatus complies with Canadian ICES 003 Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Compliance Regulations For Australia and New Zealand This equipment complies with the C Tick labeling requirements for Australia and in New Zealand As a radio transmitter this device complies
19. last 6 digits of the Ethernet MAC address of the device which is used when registering the device with a Cloud Service Both of these numbers uniquely identify your device on the Internet Protocol IP network www rainforestautomation com 13 rainforest EAGLE automation User Manual Web Viewer Functions Your EAGLE internal web server can be accessed directly on your local home network or from anywhere via Meter ralnforestcloud com The user interface is the Web Viewer It has four Function Buttons down the right side These buttons can be used to see more detailed information such as historical data and status details as well as allowing you to control configuration settings lt Messages The button corresponding to the active function is shown in light gray with black letters The inactive functions are shown ii Settings as darker buttons with white lettering Buttons will turn lighter as the cursor passes over them but they do not become active until the button is clicked la History Meter Button Clicking the Meter button takes you to the Usage page This page shows your usage data from the meter Current Usage BAWWOCg severe A Meter Set by User Price per kWh i DI H istory 9 66 Est Cost per hour DK Messa es 68 5 7 087 tlt Settings There are two display modes e Current Usage shown above displays the rate at which you are consuming energy in kilowatts This is shown
20. ld see the Usage page N rainforest My Account Gateway Log Out Gli Usage A Meter Set by User Price per kWh k i il H istory 9 66 Est Cost per hour DX Messa es 68 5 3 7 087 lt Settings 8 Www rainforestautomation com rainforest EAGLE o matio n User Manual Features of Your EAGLE Status LED Lights Information Keyholes for Label IFK O MN Wall Mount moose Sb3b 2329 7409 Yo http eagle 0006CE local CloudiD 0006CE dd FEC CECO Ri pri N27879 t Model RNAn Z109 EAGLE stormati Hardware Ports Www rainforestautomation com rainforest EAGLE automati User Manual Introduction to Your EAGLE Congratulations on getting an EAGLE the most versatile link to your smart meter energy information This device is a compact gateway that connects directly to the smart meter using ZigBee wireless lt reads the meter in real time and streams the data to your home network You can also direct the data to the internet to take advantage of the many Cloud Services available Your EAGLE helps you track the energy consumption of your home whether you are home or not This will help you take control of your usage and allow you to save energy and lower your utility bills It s easy to get started just plug in your EAGLE and log into rainforestcloud com with your web browser Your EAGLE has a built in web server that provides a simple Web Viewer that you can use to see your s
21. mart meter data Any device including your smartphone or tablet that has a web browser can be used to view your data from anywhere that you have internet access It is also possible to see your smart meter energy data without going through the internet If you are connected to the same router as your EAGLE you can connect directly to it and use its Web Viewer In addition to the Web Viewer there is also a free EnergyVUE app available on iTunes and Google Play that will let you see your smart meter energy data directly on your IOS and Android devices Your EAGLE can also connect you to an online Cloud Service There are quite a number of Cloud Services available providing all sorts of detailed data analysis attractive graphics and helpful household suggestions There are also opportunities for social networking and even ways to earn money and merchandise Your EAGLE has been designed to talk to all of these Cloud Services It is an open system that uses industry standard communication protocols and is not tied to any particular service To make things easy a menu of compatible Cloud Services is provided to enable you to connect to the service of your choice with just a few mouse clicks Www rainforestautomation com rainforest EAGLE N eee eee ee User Manual EAGLE Status LED Lights Your EAGLE has four LED lights at the front of the top of the device These lights give you a quick way to check the status of you
22. me and URL internet address of the service www rainforestautomation com 21 22 rainforest EAGLE automation User Manual ris A Meter Not Configured la History VIESCETRSS ld XVI Gg REA Inc Cloud http example com Add Cloud TY Settings After filling these in clicking the Add Cloud button at the bottom right will add this service to the Cloud List Clicking the subtract cloud icon will remove the currently selected provider from the Cloud List Note that you cannot remove any of the pre loaded providers from the Cloud List Smart Meter Sub Page Expanding the Smart Meter status bar on the Settings page brings up the Smart Meter sub page Smart Meter Connected CH 38 alll Eagle Zigbee alal History Smart Meter DX Messages MAC PANID Disconnect L Settings This sub page provides information about the ZigBee wireless link between your EAGLE and the smart meter Clicking the Disconnect button in the lower right corner terminates the connection to the smart meter The meter will not talk to the EAGLE again until it is re provisioned by the utility This function can be used to move the EAGLE to a different meter www rainforestautomation com rainforest EAGLE automation User Manual Advanced Settings Page The Advanced Settings page can be reached by clicking the gear icon in the lower right corner of the EAGLE sub page FAGLE February 17 201
23. r device as lis yn e Power LED shows that the device is powered on It should always be on when the unit is plugged in e Ethernet LED shows the status of the connection to the local Ethernet network When the link is active the light will be flashing When an IP address is obtained the light will be on constantly e Cloud LED shows the status of the connection to a cloud service When the user has enabled the cloud service the light will be flashing When successfully sending and receiving data with the cloud service the light will be on constantly This status LED is just for third party cloud services and does not indicate the status of the connection to rainforestcloud com e kX ZigBee LED shows the status of the ZigBee link to the meter Initially it will flash briefly once per second Once the meter has been found the light will flash longer every three seconds Finally when the connection to the meter is established the light will stay on continuously Normally all four LED lights should be on continuously when the unit is in normal operation Www rainforestautomation com rainforest EAGLE automation User Manual EAGLE Hardware Ports Your EAGLE has three interface ports on the back From right to left these ports are e Power the included AC adapter plugs into this socket The other end of the adapter plugs into a nearby power outle
24. raph The data will be in a CSV file which can be opened with a spreadsheet program Www rainforestautomation com 1 rainforest EAGLE automation User Manual Messages Button Clicking the Messages button takes you to a page that can display text messages sent to you by your utility 08 17 2012 8 00 pm EN Meter Very hot weekend predicted Demand will MR History be high Please try to moderate usage gt lt Messages 1 Settings When a new text message is received from the meter you will see the Messages button pulse red to indicate that there is an active message When you click on the button the message will be displayed A message can be up to 128 characters long If the message requires an acknowledgment you will see the red Confirm button in the lower right corner of the message Www rainforestautomation com rainforest EAGLE automation User Manual Settings Button Clicking the Settings button takes you to the main Settings page This page contains several collapsed bars representing sub pages Each bar contains summary status information about that sub page and will expand to a full separate screen when selected EAGLE November 18 2013 16 21 W Meter v ntemmet Connected alt History Smart Meter Connected CH 14 ill XA Settings The status bars on the Settings page are color coded to indicate status Bars are green for normal operation while a red color indica
25. rnet cable into a port on your router and the other end into the Ethernet port on your EAGLE 2 Plug the AC adapter into a nearby wall outlet and plug the other end into the power socket on your EAGLE 3 Allow three minutes for the device to boot up You should see that 3 of the 4 status LED lights not the Cloud are se all on continuously This indicates that BE O A the unit is functioning normally O O O O www rainforestautomation com rainforest EAGLE automation User Manual Step 4 Create your Cloud Account Using your web browser go to rainforestcloud com You will see the Rainforest Login page Click on the word Register in the lower right corner A rainforest amp u iI o Ma tl A Forgot Password Fill in the registration information Click the I m not a robot box then click the blue Register bar at the bottom of the page You will see a message that tells you that an email has been sent to you Check your email to find the message from Rainforest Automation with the subject line Please confirm Your Registration Click the link in the message From Rainforest Automation lt registration rainforestautomation com gt Subject Please confirm Your Registration Thank you for registering to Rainforest Automation s user portal Please confirm your registration by clic gt Thank you Rainforest Automation Inc This will send you back to your browser to a page th
26. so possible that the price can be read directly from the smart meter if the meter supports this feature In this case the Rate Label will be set by the meter and can be up to 12 characters long If no price value has been set either by the smart meter or manually then the words Not set will be shown in place of the price Below the price is the estimated cost per hour This is calculated from the current price per kWh multiplied by the current rate of energy consumption Below this is the Fast Update button Clicking this button will cause your EAGLE to ask the meter for faster updates Once this is done the faster rate will be in effect for 60 seconds Note the small green dot that will appear at the top left corner of the Usage page This indicates when an update to the usage has been received from the meter and allows you to see how fast your EAGLE is getting meter data Www rainforestautomation com 15 rainforest EAGLE automation User Manual History Button Clicking the History button takes you to a page that can display graphs of your historical usage la History i 3PM SPM 7PM 9PM 11PM 14M 34M SAM 7AM 9AM 114M 1PM 3PM settings Demand W Hour TE Week There are two display modes that you can select from the dropdown menu in the bottom left corner of the screen e Demand shown above displays the rate at which you are consuming energy in kilowatts over time This is shown as an
27. t e Ethernet the included Ethernet cable plugs into this socket The other end of the cable plugs into your local network router This should be plugged in first before plugging the power in e USB this socket can be used to expand the functions of the EAGLE Nothing should be plugged into this socket 12 Www rainforestautomation com rainforest EAGLE automation User Manual Understanding the Information Label The information Label is located on the underside of your EAGLE It contains important information that you will need to operate your device econo crn MAC A zose f IMMINENTE A MAC DI n N 0000 0000 0000 0000 an aa Ethernet http eagle 000000 loca Local Web Area CloudiD 000000 Address 4 FECE Cloud ID Zig Bee N27879 eae product Model RFA Z109 EAGLE Rainforest Automation Inc FCC ID YOXRFA Z109 IC 8919A RFAZ109 Made in the USA e ZigBee Area This area at the top of the label has two fields o MAC the 802 15 4 ZigBee MACID o IN the Install code for the device Both of these numbers are unique to your device and are loaded into your meter by your utility Only when the meter is loaded with these numbers can it communicate with your EAGLE e Ethernet Area This area in the middle of the label has two fields o Local the local URL or Local Web Address of your EAGLE which is used to find it on your Local Area Network LAN using your web browser o CloudiD the
28. t Country ss Es Select State Province Select Utility M reCAPTCHA ie Near the bottom you will need to click the I m not a fim not a robot b robot box then click the blue Register bar You will see a message that tells you that an email has been sent to you www rainforestautomation com 25 rainforest EAGLE omation User Manual Check your email to find the message from Rainforest Automation with the subject line Please confirm Your Registration From Rainforest Automation lt registration rainforestautomation com gt i Subject Please confirm Your Registration Thank you for registering to Rainforest Automation s user portal Please confirm your registration by clic Goins Thank you Rainforest Automation Inc Click the link in the message This will send you to your browser and to a page that confirms that your account has been activated Your account has been activated Click the word here to go to the Login page p go to login page Login user email com Forgot Password Register Enter your email address and password at the Login page and click the blue submit bar You are now logged in to your Cloud Account 26 Www rainforestautomation com rainforest EAGLE automation User Manual Managing your Gateway List The Gateway page shows a list of EAGLE gateways that you can connect to It is the default page when you log in to your Cloud Account
29. tab in the My House screen to see your near real time data My House g Overview Live History Widget Data Alerts Settings last 10 minutes last hour Live My House Updates every 10 seconds 16 538 Q 2 92 watts per hour energy used today 0 00 energy used yesterday 0 00 current consumption rate last ten minutes Www rainforestautomation com 33 rainforest EAGLE automation User Manual Connecting to BlueDot Set up the EAGLE upload server 1 Inthe Cloud sub page select BlueDot from the drop down menu for Provider 2 Click the Set Cloud button clud Not Configured n Meter Set Cloud ib Settings Cloud ID Provider BlueDot y URL https api bluedot com v1 gene Last Upload Get a BlueDot account Open another window in your web browser and go to BlueDot com Click the Signup link at the top of the web page BLUEDOT HowltWorks ContactUs Lod signup f in y You will see the Signup page Fill in the form and click the blue Signup button at the bottom Signup Please fill out the following fields to signup Email Address me email com An email will be sent to this address to complete the signup process Password 0000000090008 LI Zip or Postal Code 12345 sor all You will see a message that tells you that an email has been sent to you Check your email to find the message from BlueDot Support with the subject line Wel
30. tes an error condition and a grey bar indicates an inactive function FASLE November 18 2013 16 14 Ww Meter MERCE Connected ial History A lt Messages Smart OO To C K CM 17 Settings Status bars can be expanded by clicking the white triangle on the far right of the bar This will expand the corresponding sub page to fill the page www rainforestautomation com 19 rainforest EAGLE automation User Manual EAGLE Sub Page Expanding the EAGLE status bar on the Settings page brings up the EAGLE sub page FASLE March 5 2015 15 23 Time From Meter From Internet ala TimeZone lt Messages ELMETE Engish v Price kWh From Meter Mawa TE 50 0966 ilf Settings This sub page is used to configure the Time Zone Language and adjust price settings e ime Select the time source either From Internet default or From Meter if no internet connection available e Timezone Click on the white info field to bring up a world map Click on your location to set your Time Zone The default is Pacific time e Language Click on the drop down list to select your preferred language for the Web Viewer only English is currently supported e Price If price is not supplied by the meter then you can set the price manually To do this enter the price in dollars in the lower right entry field and click the Set button If the price is supplied by the meter then you will just see
31. tion com 31 32 rainforest EAGLE a u o ma ti on User Manual After you sign in Google will ask you to allow Wattvision to connect to your account abc def xyz Google is not a the contents of wattvision or its owners If you sign in Google will sh Allow No thanks ioni i Sign in to another account ol fox to orti dare uu u_u ci ini LD aaar san oe tbe Click the Allow button You will now be returned to the Wattvision site My House Rainforest Wattvision Follow the steps below to complete pairing of your Rainforest sensor and Wattvision Your Cloud ID is found on your Rainforest Gateway s Label Enter it below Sensor Model Eagle by Rainforest Automation SJ House Create a new house Cloud ID Cloud ID 0012cd Connect Rainforest to Wattvision In the Cloud ID field enter the 6 digit Cloud ID found on the Information Label on the underside of the EAGLE Then click the big green Connect Rainforest to Wattvision button You should then see the My House screen My House g 3 Overview Live History Widget Data Alerts Settings My House Sensor Status Sensor online Reporting data Live wee ee ee ee ee ee ee ee ee eB eB ee ee ee ee ee eB ee ee ee eK Www rainforestautomation com rainforest EAGLE automation User Manual View your Wattvision data Click the Live
32. two symbols e Clicking on the Connect f icon will connect you directly to the listed EAGLE and will show its Web Viewer e Clickingon the Delete x icon will remove the listed EAGLE from the list of gateways Managing your Cloud Account The My Account page allows you to modify the information in your Cloud Account profile My Account email first name unspecified last name new password confirm new password unchanged street country Select Country state province Select State Province zip postal code utility Select Utility phone number unspecined Update Changes www rainforestautomation com rainforest EAGLE automation User Manual Once you have entered the information click the blue Update Changes bar to save the new information This page allows you to change the password for your Cloud Account Note that changing your password may affect the ability of applications such as smartphone apps to access your EAGLE through the web Www rainforestautomation com 29 30 rainforest EAGLE automation User Manual Connecting to a Cloud Service To set up a connection to the Cloud Service of your choice click the Settings button in the lower right of the Web Viewer then expand the Cloud status bar to bring up the Cloud sub page EN Meter FAGLE November 18 2013 16 14 v AA Meter lal History ntemet Connected alt History gt lt Messages NSA Messag
33. ud com but will also lock you out for local access without authorization Once you turn on security you should use rainforestcloud com Once you check the Enable Security box you will be asked to confirm that you wish to change the security configuration Then you will be asked to enter the Cloud ID and Install Code for your EAGLE These numbers can be found on the Information Label that is on the underside of the unit Www rainforestautomation com 3 38 rainforest EAGLE automation User Manual ML l MU WMA l IL LU Install Code Cloud ID O OFECEG LigBee N27879 cen i product Model RFA Z109 EAGLE Rainforest Automation Inc FCC ID YCXRFA Z109 IC 8919A RFAZ109 Made in the USA Be sure that you enter both of these numbers without spaces or any punctuation such as colons or quotes and without any prefixes such as Ox All letters must be lowercase Finally you will be asked to confirm once again www rainforestautomation com rainforest EAGLE auto ma ti o n User Manual Troubleshooting Guide Symptom You cannot add your EAGLE to your Cloud Account The Add New o o oo Gateway screen says Security is not enabled on the Gateway Connect locally to your EAGLE see the Connecting Locally to your EAGLE section Go to the Advanced Settings page Check the Enable Security box in the bottom left corner Confirm that you wish to change the s
34. with the requirements of AS NZS 4268 2008 as designated in the Radiocommunications Short Range Devices Standard 2004 for Australia and as required by the Radiocommunications Regulations General Users Radio License for Short Range Devices Notice 2011 for New Zealand This device is a Category A device as defined in the Radiocommunications Compliance Labeling Electromagnetic Radiation Notice 2003 Www rainforestautomation com rainforest EAGLE Ni I i User Manual Quick Setup Step 1 Prerequisite software and hardware 1 A free Ethernet porton a router directly connected to the Internet 2 A PCorother device with a web browser Step 2 Provision the EAGLE Your EAGLE must be registered with your utility to connect to the smart meter You will need to contact your utility with two numbers MAC Address and Install Code that can be found on the Information Label on the underside of your EAGLE Il UW insta _ NINNA MAC Code v gt 0000 0000 0000 0000 Address http eagle 000000 local CloudiD 000000 N27879 Model RFA Z109 EAGLE FECEC Rainforest Automation Inc FCC ID YCXRFA Z109 IC 8919A RFAZ109 Made in the USA Note that it may take some time for your utility to enable the smart meter to connect with your device You must wait until this process is complete before proceeding your EAGLE will not function correctly until the smart meter is enabled Step 3 Power up the EAGLE 1 Plug the Ethe
Download Pdf Manuals
Related Search