Home
Quick-start Guide
Contents
1. email us at info bioerc com 4
2. BC Auto Wire Back Shell Gea When the treatment is complete the device will automatically shut itself off Once that has occurred firmly grasp the patient cables on the sleeve portion of the plug and pull straight back to remove from the device You should feel the sleeve slide back and the locking mechanism disengage Do NOT twist the plug or pull from the back shell or wire to remove 6 Recharge the device The middle connector is for charging the device with the provided charger Do NOT attempt to charge the device with the USB cable Prior to charging turn off the device and unplug the patient cables Connect the charger to the device by aligning the arrow above the middle connector to the arrow on the plug and pushing straight in until you hear a click If the device is on when plugged in it will beep and automatically enter a mode to power itself off For further questions or concerns please call 626 792 0200 or email us at info bioerc com FOR PATIENT USE AC Cord Charger When connected to the device plug the AC cord into the other end of the charger and then into a 110 120V outlet At first you will see a red light on the charger After about 3 hours it will turn a steady green color when charging is complete To disconnect the battery charger from the device firmly grasp the grommet and pull straight back away from the device without rotating it Do NOT pull the wire or the body of the connector This i
3. FOR PATIENT USE Quick Guide to ODIN1 ODIN1 D Read BRC 2200 user manual for complete instructions including all warnings and cautions before operating device The device is equipped with locking connectors Please refer to Section 5 of this Guide prior to attempting to unplug patient cables or charger LU WARNING Hydrogel electrodes should not be used with Treatment Programs G H and I Contact Bioelectric Research Corporation for foam electrodes for use with those programs Batte ry Touch Screen Indicator Indicator Light Battery Connector Electrode Connector On Off Button 1 Place an electrode on each wrist or on each ankle Position electrodes so that hand foot icon is pointing toward hand foot when placed on the wrist or ankle respectively Your medical provider will tell you where to place the electrodes For further questions or concerns please call 626 792 0200 or email us at info bioerc com FOR PATIENT USE 2 Connect the patient cables Line up the arrows to connect 3 Press and hold the On Off button to turn on the device Verify the correct patient name and treatment is displayed on the screen SS i JANUARY 1 2012 1 15PM Gr g i ee Patent Ch Patient Inf ti ange ratent information John Doe J Treatment ABO Change Program Manua SETTINGS PROGRAM PATIENT hi TREATMENT A Do NOT touch On Off Button when screen
4. goes dark In order to save battery power the screen will go DARK after a few seconds the number of seconds is adjustable in the Settings tab If you see the screen is black just touch it with your finger it will power up and the screen will be immediately visible If the device is On the indicator light will blink once every second 4 Press the Treatment button to begin treatment JANUARY 1 2012 1 15PM Gm Start 1 15PM End 3 55PM 15 V 15 K 1mA 1 15PM Gan Program A JOHN DOE 68 sates Change Patient Information John Doe e O C1 22 59 Treatment ABC Change Program Auto dh Procnampanenr a ncn es p TREATMENT gt SETTINGS dh PROGRAM PATIENT For further questions or concerns please call 626 792 0200 or email us at info bioerc com 2 FOR PATIENT USE Patients may feel a mild intermittent tingling or prickling sensation If any significant pain or burning sensation is felt immediately stop the device and remove the electrodes Release Button Locking Tab Locking Sleeve Locking Sleeve n To connect the clip to the device slide the locking tab into the locking sleeve until you hear a click To disconnect the clip press and hold the release button while sliding the locking tab out of the locking sleeve 5 When treatment is complete unplug the patient cables from the device ODIN I1 Sleeve Patient JOHN DOE Treatment A
5. s illustrated in the photo and yellow warning graphic below Turn on device and look on device screen for battery indicator located on the upper right side It should show 4 bars when fully charged Grommet Grab plug by grommet to remove More Info 1 Press the Pause button to pause the treatment If you can wait until the end of the cycle a countdown timer will appear on the pause screen press the Pause at End of Cycle button The device will alert you when the end of cycle has occurred and the treatment will automatically pause Otherwise press Pause Immediately Press the Run button to resume treatment 2 Incase of mild discomfort press Reduce Power 3 When the treatment is complete the device will beep and automatically turn off The electrodes may be attached to either the wrists or ankles Only place the electrodes over intact skin Do not place directly over open wounds 5 Ifthe electrodes become too dry or are not connected properly the device will alert you The device will then provide instructions on how to fix the most common electrode problems 6 Recharge the device after 3 programs or less Connect the battery charger plug to the middle connector located between the electrode connectors Allow 3 hours to fully charge the device It is OK to let it charge over night but be sure to disconnect charger in the morning For further questions or concerns please call 626 792 0200 or
Download Pdf Manuals
Related Search
Related Contents
2014 Jeep Compass Owner`s Manual RAS-07EKH/RAS-07EAH RAS-09EKH/RAS-09EAH Victor Technology 1297 calculator Grundig KM 7280 easyRAID Q16PS-F4R3 Hardware User Manual Téléchargez - Haier.com Worldwide - Select your local country or Copyright © All rights reserved.
Failed to retrieve file