Instruction Manual
Contents
1. Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 10 28 Page 1 PE Kun A DUST MANAGER USER INSTRUCTIONS Hoover Stabiliser FINAL Vs2c 01 03 06 gxp User s manual This cleaner should only be used for its intended purpose as described in these instructions Ensure that these are fully understood before operating this appliance Only use attachments recommended or supplied by Hoover When using cleaning tools ensure that the cleaner is kept in the upright parked position This will avoid possible damage to the carpet or floor covering When cleaning stairs DO NOT position the cleaner above you STATIC ELECTRICITY Some carpets can cause a small build up of static electricity Any static discharge is not hazardous to health DO NOT use your cleaner out of doors or on any wet surface or for wet pick up Keep hands feet loose clothing and hair away from rotating brushes DO NOT pick up hard or sharp objects matches cigarette ends or other similar items HOOVER SERVICE HOOVER SPARES Use only HOOVER spares 01 03 2006 10 28 Page 2 DO NOT pick up flammable liquids such as cleaning fluids petrol etc or their vapours Aerosol sprays may be flammable DO NOT spray near cleaner SUPPLY CORD DO NOT run over the supply cord when using your cleaner or remove the plug by pulling on the supply cord FAULTS DO NOT continue to use your cleaner if it appears to be faulty If the supply cord is d2. Failure to do so may cause damage to the floor surface 3 Locate hose retainer on lower hose support 8 Position hose over hose supports Push handgrip firmly into socket Clip tools to back of cleaner Ensure that the cleaner is in an upright parked position 7 M N Check that dust container is fitted Slide knob to position best suited to depth of carpet pile POWER SWITCH SETTING 7 Using this cleaner for carpets with pile greater than 30mm is not recommended HANDLE LOCK RELEASE gt Unlock the handle by pressing down on pedal with foot For cleaning under low furniture and some maintenance tasks simply press pedal again and 4 Switching on and off lower handle to floor Push bottom of the switch to switch on Push top of switch to switch off Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 CLEANING TOOLS IMPORTANT When using cleaning tools the cleaner must be kept in the 10 28 Page 5 S upright parked position particularly when cleaning stairs The nozzle e height should also be set to tool mode Pet Hair Remover Ideal for removing pet hairs Do not touch the rotating brush Telescopic Tube Fitted on the flexible hose and with accessories at its end its ideal for stair cleaning It extends to minimise stretching and bending All accessories can fit on the end of the flexible tube Combine accessories depending on use ALWAYS attac
3. before checking the brushes or removing Hold the brush assembly and and remove the plug from the Ast stretch the belt until brush electricity supply before dismantling mountings slot down into the cleaner cleaner housing Rotate the brush to ensure free movement of the belt If your cleaner is not picking up efficiently the belt or brushes or both may need replacing but first make sure you have This cleaner is unlikely to become blocked except by overfilling of the dust container or accidentally picking up large solid objects Clearing a blockage is simple i i If cleaning tool in use Emptied the dust container cleaning tools were in use e Cleaned filters check cleaning tool and Checked for blockages extension tube first Next oO i check hose handgrip to remove grip ribbed ring as Refit hood shown turn in direction of E n e Refit hood ensuring the lugs arrow and ease apart along the front of hood are located in the slots along the front edge of baseplate NW e Secure hood using screws To check the hose stretch it D A and B to full length and switch on the cleaner the suction will Remove hood dislodge most obstructions If e Prise off carpet care control knob this is unsuccessful switch off EP TR screws A and B and unplug the cleaner ift off hoo Remove the hose by turning it anti clockwise as shown A Refit carpet care control Detach cassette and remove knob blockage e Ensure the rai
4. amaged stop using the cleaner IMMEDIATELY The supply cord must be replaced by an authorised Hoover service engineer to avoid a safety hazard AFTER USE Switch the cleaner off and remove the plug from the electricity supply Always switch off and remove the plug before cleaning the appliance or attempting any maintenance task HOOVER SERVICE To ensure the continued safe and efficient operation of this appliance we recommend that any servicing or repairs are only carried out by an authorised Hoover service engineer 08705 400 600 01204 556 III IMPORTANT SAFETY REMINDERS Congratulations on the purchase of your new Hoover Dust Manager This highly advanced machine with new technology unique to Hoover makes cleaning easier and more efficient You ll find it kinder to your carpets and to you Please take the time to read this manual carefully You ll be ready to make the most of the special features only the new Hoover Dust Manager can offer WARNING ELECTRICITY CAN BE EXTREMELY DANGEROUS This appliance is double insulted and must not be earthed The plug is fitted with a 13 amp fuse IMPORTANT The wires in the mains lead are coloured in accordance with the following code Blue NEUTRAL Brown LIVE HOOVER OUST MANAGER Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 10 28 Page 3 B GETTING TO KNOW YOUR CLEANER Effortless Handle cleaning with your new Hoove
5. h hose retainer to hose hook when using cleaning tools Unhook after use CLEANING THE STAIRS It is dangerous for the cleaner to be above you at the top of the stairs ALWAYS work with the cleaner below you Ensure it is positioned up against the bottom step DO NOT attach hose retainer when cleaning the stairs Features vary according to model STABILISER FEATURE The stair STABILISER has been designed to improve cleaner stability when you pull on the hose while stair cleaning It can be adjusted to suit any staircase Location The STABILISER stability device is located at the back of the cleaner Pull the bottom of the device to release it from its storage position Operation Lift the device upwards to the position shown in the diagram Simultaneously squeeze the finger tabs and extend the device Use Place the cleaner against the stairs and the STABILISER in the position shown Use the stair cleaning hose and accessories as usual To return the cleaner to carpet mode repeat the above process in reverse Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 10 28 Page 6 S CHANGING BELT OR BRUSHES o CLEARING A BLOCKAGE IMPORTANT Switch cleaner off and Refit brush assembly IMPORTANT Switch the cleaner off remove plug from electricity supply
6. hat independent approval further information telephone the HOOVER Service Office is the best way of demonstrating safety in design and manufacture have set in Quality Safety Hoover service and the Environment Tel 08705 400 600 The British Electrotechnical Should you require service at any time Approvals Board BEAB the please call the HOOVER Service Office Quality independent UK national BSI ISO9001 authority for the safety of Hoover have a computerised nationwide domestic electrical appliances service network of over 500 engineers i ensure that European Safety who will respond guickly to your call and a Ed Standards are met and are guarantee your repair for 12 months have sasn maintained throughout the independently production life of the appliance assessed for quality Our products are made All appliances which pass these using a quality system tests are permitted to carry this which meets the BEAB mark of safety requirements of ISO 9001 BEAB p GUARANTEE STATEMENT The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased the bill of sale or receipt must be produced when making any claim under the terms of this guarantee Environment Weee Directive This appliance is marked according to the European Directive 2002 96 EC on Waste Elec
7. mally maintenance free this component should not be washed If a replacement is correct the fault reguired please contact our spares department It will take about 30 minutes for the cut out to automatically reset The exhaust filter should be washed every 3 months press down on the latch to remove the exhaust cover Hoover Limited Pentrebach IMPORTANT Do not run cleaner over the supply and filter cord as this could damage the supply cord insulation Merthyr Tydfil Wash under hand warm water Mid Glamorgan Remove excess water by shaking and leave to dry for CF48 4TU 24 hours 2006 Registered Trade Mark Features vary according to model 8 Part Number 0565 5214
8. r Cleaner body Cord storage swivel hook Supply cord Dusting brush Pet Hair Remover On Off switch Grooming nozzle NYY q Bx Hose supports Long crevice tool When first unpacking your cleaner please Door release check all items are included Carrying handle Flexible hose KE KA AS A 5 7 S k A Hose retainer Hose supports Q If any parts are missing contact your retailer or call the Hoover helpline on 08705 400 600 Exhaust filter cover behind Stabiliser Extension tube or Telescopic tube Handle lock release M Hose hook Stabiliser Carpet care control Features vary according to model Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 10 28 Page 4 S PREPARING TO USE YOUR CLEANER CARPET HEIGHT SELECTOR The carpet height selector raises or lowers the height of the nozzle The nozzle height will not change until the handle is released Try various settings until you get the best results for each of your carpets IMPORTANT When cleaning hard floors such as vinyl or linoleum move the Height Right selector knob to the Insert handle into body of cleaner Slide into position Ensure handle is flush with body of cleaner Tighten large screw pre fitted to handle upper hole Insert small screw into handle lower hole and tighten Locate hose end turn clockwise to lock Hard floor position
9. sed face T is towards the front of the For blockages in cleaner base cleaner 1 Turn the cleaner over and check that the brushes are free to rotate Remove brush assembly Inspect belt for signs of wear Removing a blockage from the Pet hair remover e To remove pull brush cleaner assembly certain models only upwards out of cleaner housing Remove belt from motor spindle then from brush assembly 2 Check for a blockage in hose socket Use a Open clip and lift cover to remove blockage piece of wire or a blunt flexible rod to remove Replace belt any obstructions Loop the new belt around the motor spindle then around the brush channel Features vary according to model 6 Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 10 28 Page 7 B Genuine HOOVER spares Hoovercare Quality Safety amp Tel 01204 556 111 Environment Safety Always replace parts with genuine Hoover To maintain your HOOVER product in spares These are available from your local peak condition you may also wish to take As the owner of a new Although safety certification of Hoover dealer or direct from Hoover out a Hoovercare policy for which an Hoover product we would electrical appliances is not When ordering parts always quote your annual payment provides a comprehensive like to tell you more about required by law in the UK Hoover model number maintenance and repair scheme For the high standards we believe t
10. trical and Electronic Equipment WEEE Subject to change without notice Z By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol on the product indicates that this product may not be treated as household waste Instead it shall be handed over to the appliance collection point for the recycling U se O n ly H OOV E R S pa res of electrical and electronic equipment Disposal must be carried out in accordance with local environment regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Hoover Stabiliser FINAL Vs2c 01 03 06 gxp 01 03 2006 10 28 Page 8 EMPTYING AND CLEANING THE DUST CASSETTE AND FILTERS Press down on door release pad and remove door Pull out the dust cassette Empty the cassette of dirt and debris Clean cyclonic mesh after each empty lt User checklist If your cleaner is not working properly run through the following checklist 1 Is there a working electricity supply to the cleaner check with another electrical product 2 1s the dust container full or choked with fine dust To empty the dust container see the ins
11. tructions on page 5 3 Is the hose blocked To clear a blockage see the instructions on page 6 4 Is there a blockage in the cleaner base To clear a blockage see the instructions on page 6 5 Are the filters blocked To clear the filters see the instructions on page 5 6 Is the nozzle height set correctly To set the carpet height selector see the instructions on page 4 7 Are the brushes rotating correctly To check the brushes see the instructions on page 6 After emptying the cassette 5 8 Has the cleaner overheated If so it will take about 30 minutes to reset itself times wash the filter and foam If there is any doubt call the Hoover Service Office for advice They may be under hand warm water Remove able to assist you over the telephone excess water by shaking and leave to dry for 24 hours Do not use a brush as this will damage the filter A service charge will be made if the cleaner is examined and found to be in working order has not been assembled in accordance with these instructions or has been used incorrectly The pre motor filter should be washed every three months Wash under hand warm water Remove excess water by shaking and leave to dry for 24 hours When completely WARNING dry refit the filter A thermal cut out switches off the cleaner to prevent a overheating if it is used when full or there is a blockage or Carbon filter dirty filters If this should happen switch off unplug and Nor
Download Pdf Manuals
Related Search