PRODUCT DATA
Contents
1. T8 T10 Electrical heatine element duct mounted The operating panel Switch for user choise Safety switch accessory Power supply iu Fresh air gt Discharge air Supply air sensor Heatine element frost protection Extract air sensor Discharee air and defrost sensor Fresh air sensor Hoom sensor 3 Fresh air Extract air gt m Supply air um gt Discharge air COMFORT 5000 BY NILAN Capacitu Heatine element accessoru Capacity water heatine element Temperature input output EE 40 30 60 40 70 40 Water heatine element Electrical heatine surface The electrical heatine surface is fitted in the air inlet duct and connected to the CTS 602 control panel and 3 x 400 V supply The electrical heatine surface can supplu up to 15 kW or 21 kW of heat Water heatine element for internal fittine The water heatine element is desiened to be built into the system and must be connected to the primary heating supply and the CTS 602 control The water heatine element includes copper pipes and aluminium fins Capacities can be seen in the table below Water side Air side Flow Pressure drop Output Flow Temperature Temperature Pressure drop before WHE after WHE over WHE I h kPa kW m h C C Pa 415 157 4 8 1000 16 zo 3 672 4 1 d 2000 16 27 4 9 871 65 10 12. 3000 16 2505 18 1036 9 0 12 0 4000 16 24 8 29 1178 11 4 13 7 5000 16 24 0 41 379 1 4 8 7 1000 16 41 6 3 612 ENS 14 1 2000 16 366 9 792 oe 18 2 3000 16 3519 18 941 ye EL 4000 16 Eure ee 1070 SI 24 7 5000 16 30 4 41 285 0 8 98 1000 16 44 8 8 455 19 157 2000 16 39 0 9 586 30 Eee 3000 16 357 18 694 4 0 23 9 4000 16 235 29 786 51 5000 16 Suo 41 AUTOMATION 56 Control External communication The CTS 602 control unit communicates bu default with Modbus RTU RS485 communication CTS system usine this form of communication can easily be connected to the unit Nilan units have an open Modbus communication i e not only can the unit be monitored but its operation can also be set in the same way as it can via the operatine panel The protocol is set up by default for a Modbus RTU 30 address but can be set to a value between 1 and 247 A Modbus converter allows you to connect one or more units to a computer to monitor and control the unit The Comfort 5000 is controlled usine its CTS 602 operatine panel featurine a wide ranee of functions e e menu con trolled operation weekly programme settings filter monitor with timer fan speed adjustment summer bypass free cool ing post heatine element control error messages etc The CTS 602 comes with factory settines includine a default settine which can be customised to operational requirements to achieve optimum operation and utilisation of the system The o
3. The water heatine surface can be built into the unit COMFORT gt 000 Technical specifications Dimensions W x Dx H Weieht Min Airvolume Max Airvolume Power consumption Power supplu Max phase 2650 x 1250 x 1500 mm 617 ke 500 m h 5300 m h 3 9 kW 3 x 400V 50 Hz 3x13A Standby power Plate type casing Aluzinc steel plate Heat exchanger type Aluminium counterflow heat exchanger Filter class Standard baefilters M5 Extract air and Fresh air Duct connections WxH 800 x 500 mm Condensate drain PVC 20 15 mm External leakaee underpressure 1 0 9 96 External leakage overpressure 2 0 9 96 Internal leakaee 3 0296 Tiehtness class IP31 1 At 250 Pa and 4000 m h according EN 13141 7 2 At 250 Pa and 4000 m h according EN 13141 7 3 At 100 Pa and 4000 m h according EN 13141 7 Motor and motor control Data for ecodesien Motortype EC Engine Fan data Motor class in accordance with IEC 60034 30 IE3 Premium efficiency Max total efficiency A D 67 9 96 Voltaee input 1x230V ECO measurement set up A D A Current overload protection Built in Efficiency level requirements 62N 2015 Control signal with third party 0 10VDC ECO efficiency level during optimal 753 control sustem operatine point l Fluid temperature air 20 40 C 20 40 Motor optimal operating point EC mator With motor controller Absorbed power 1 954 kW Airflow 4863 m h
4. Total pressure 897 Pa RPM during optimal operating point 2311 Conditions according with EC327 2011 COMFORT 5000 BY NILAN Functional diaeram T10 A rt HO m 4 B 2 Connections Automation 1 Fresh air Te T7 Supply air sensor Supply air T9 TC Heating element frost protection 3 Extract air T3 Extract air sensor 4 Discharge air T4 Discharge air and defrost sensor 5 Condensate drain T8 Fresh air sensor 6 Electric and water heatine T10 Room sensor PLANNING DATA Nilan units are tested in accordance with the valid standards of accredited independent test institutes Capacity Capacity of standard unit as a function of q and P se SFP values according to 13141 7 are for standard units with M5 filter in extract air F7 filter in fresh air and no heating element SFP values comprise the unit s total power comsumption excl control BUE W m3 h Conversion factor 3600 P 200 800 CLR 2 700 600 200 NE ETT t t 400 m O O m MN 300 Haor MN 200 11200702 OR Pressurelos waterhgatine ESSN Q 1000 2000 3000 4000 2000 6000 100 g 1 5 200 400 600 800 1000 1200 1400 1600 Temperature efficiencu Temperature efficiency for unit with counterflow heat exchanger according to EN308 dry Temperature efficiency EN308 tsup
5. fire alarm contacts In case of an alarm smoke dampers are closed and the unit stops Outlet for joint alarm Allows control from both the extract air and supply air side Via bypass This allows you to choose whether to run the system at a higher or the highest ventilation step during cooline The weekly proeramme has an option for settine cooline at nieht Allows you to set the regulator to control the intake air temperature supply air only available if the control unit has been confieured for a supply heatine element e Temperature sensor T7 is an supply air sensor e Integrated frost protection for external water heating element e Motorised valve and circulation pump control unit e Temperature sensor T7 is an supply air sensor e Overheating protection There is a possibility for a delayed start up by the fans when a closing damper is installed Allows you to make additional connections User option 2 overrides User option 1 e Up to 500 W direct e Can give the signal for external heating if the defrost function is used e Switching the central heating system on off Allows you to restore the factory settines Allows you to test the unit s functions manually Option for setting the relevant language Danish Finnish Norweeian Swedish German Enelish French 13 Standard Accessories OPERAIIUN Frost protection All ventilation units with a counterflow heat exchanger will ice up if the outd
6. made of highly corrosion resistant marine aluminium The counterflow heat exchaneers have an enerey efficiency of more than 80 and prevent odours beine transferred from the extracted air to the supply air The CTS 602 control allows for cooline recovery Frost protection An electric heater can be purchased for frost protec tion This prevents the formation of ice in the coun terflow heat in the event of lone periods of frost COMFORT 5000 BY NILAN Modulatine 10096 bypass An automatic bypass valve directs the fresh air past the heat exchanger when waste heat recovery is not necessary thus conservine energy Filters The Comfort 5000 is supplied with bae filters An M5 filter in the air exhaust and an F7 filter for fresh air are supplied as standard The CTS 602 control has a built in timer controlled alarm for chanee of filter It is possible to install a pres sure controlled filter monitor accessory Construction The Comfort 5000 is housed in a strone frame structure of Aluzinc with 50 mm insulation Base Comfort 5000 is delivered with a robust built in base A foundation and vibration absorbers can be ordered as an accessory This ensures a noiceless installation Heatine elements Pressure control External water or electric heatine elements reeu The extraction and or supply fan can be operated lated by the CTS 602 control can be purchased with the aid of a pressure transmitter
7. PRODUC T DATA COMFORT5000BYNILAN Ventilation amp passive heat recoveru e Commerc ia Passive Ventilation heat recover y SBIOB TER COMFORT 2000 The Comfort 5000 is a ventilation unit suitable for central venti lation of residential buildines schools offices and business facili ties with a ventilation requirement of up to 5300 m h Every component has been carefully selected with a view to un surpassed quality and each component is tested throughout the entire production process as are the finished units before leav ine the factory This quality control reflects our high standards which not only exceed market requirements but also take them several steps further Automatic control The Comfort 5000 is supplied with an inteerated CTS 602 control which is operated by the enclosed control panel The modern CTS 602 control communicates Modbus RTU RS485 CTS system usine this type of communication can easily be connected to the device Plue fans The two fan sections consist of enerey efficient EC mo tors with built in motor controllers operated by a 0 10V sienal The efficient fan wheels haverear facine impellers are extremelu quiet Doors The large doors allow easy access for the chaneine the filters as well as servicine of the unit The doors are mounted with loockable safty doorhandles Counterflow heat exchanger Heat recovery is achieved by four counter flow heat exchangers
8. desired supply air temperature to be maintained sprine summer and autumn Allows you to choose whether to switch humidity sensors and or CO sensors on and off Allows you to set a hieher or lower ventilation step in the case of high low air humidity Allows you to set a hieher or lower ventilation step in the case of a hieh low CO level Allows you to select a low ventilation step in the case of low outside temperatures and air humidity Temperature based automatic function for defrosting the heat exchanger In case of failine heatine system the unit is turned off to avoid further cooline with a risk of the water heatine coil frost burstine Allows you to select the temperature sensor which will control the unit e T15 ROOM panel sensor e T 10 EXT fitted in a representative extraction valve e EXTRACT extract air Stops the unit at alow room temperature Hereby is cooling of the home avoided in case of a failing central heatine system Standard set to OFF Can be set from 1 to 20 deerees and is controlled bu e T15 ROOM panel sensor e T 10 EXT fitted in a representative extraction valve EXHAUST extract air Allows you to set the regulator to control the room temperature Allows you to set four ventilation steps Supply air and extract air are set individually Step 1 lt 25 Step 2 lt 45 Step 3 lt 70 Step 4 lt 100 This allows you to connect fire detectine thermostats smoke detectors and other
9. ise Nilan A S reserves the right without prior notice to change products and information material All trademarks are the property of Nilan A S All rights reserved
10. on and maintenance we have created a series of information material which is available for download at www nilan dk Montagevejledning Brugervejledning Malskema AW G de um mm i eiie ie E D NE gt i e e a 15 NILAN 15 NILAN nana 4 Alle m l er i mm Brochure Product data Installation User manual Drawines instructions General information about the solution Technical information to ensure correct Detailed guide for Detailed euide for instal regulation of the Tender documents and 3D drawings are available to down load for plannine purposes and its benefits choice of solution lation and initial adjust solution to ensure ment of the optimum day to day solution operation Visit us at www nilan dk to find out WWW N LAN more about our company and solutions i download further information and find uour nearest dealer 4l x d OUTSTANDING INDOOR CLIMATE Nilan A S Nilanvej 8 22 Hedensted Danmark Tif 45 7 6 752500 Fax A5 6752525 ilan alnilan ak www nilan dk Ver 2 05 2015 02 Nilan A S assumes no responsibility for any errors or omissions in the printed information material or for loss or damage that may follow from the use of such published materials whether such loss of damage is caused by errors or inexpediencies in the material or otherw
11. oor temperature is below freezine for a proloneed period The extracted air condenses when it is cooled down durine heat recovery The high temperature efficiency will slowly turn the condensate to ice which will block up the counterflow heat exchaneer unless action is taken to remedy this Consideration must be eiven to whether the unit s operation can be protected during alenethy period of frost or whether it is acceptable to decrease its operation In homes which are occupied at nieht it would be advisable to protect the unit aeainst frost when the outdoor temperature is coldest by usine a pre heatine element the other hand if the ventilation is for an office it may be acceptable to decrease the operatine level at nieht nt 26 With pre heater e b rien 7 3 C yw o c 0 E Dunes 8 E Defrost function Operation lce buildine Defrost Ice buildine Defrost The energy used for the preheating is not wasted as it ensures a constant high temperature efficiency Frost protection Yes After 30 min No Ja le DIMENSIONAL DRAWING m 2650 Extract air CC lt I Fresh air Discharee air al d Condensation drain 1400 L aD and KT 1000 Recommended service clearance IL ALLESSURIES Pressure transmit
12. peratine panel must be placed in a dry frost free loca tion at least 1 5 m above floor level and at least 0 5 m from any corner Avoid placing the panel an external wall or in areas in direct sunlieht Operating instructions for the CTS 602 can be found in a sepa rate user manual supplied with the unit CTS Computer Konverter Modbus 10 Functional overview 3 levels Weekly plan User option 1 Alarms Filter monitor Pressure controlled filter monitor Bypass Air quality Humidity control control Air exchange Defrost function Frostprotection Temperature control Room low Room control Air volume Fire alarm Joint alarm Constant pressure control Cooline Intake air control External heating element External electric heating element Delayed start up Expansion PCB Reset Manual test Language COMFORT 5000 BY NILAN The control function is divided into 3 levels User Service Factory with various options at each level There is an option for you to set your own weekly programme This allows you to override the operating mode in the main menu via an external potential free contact or PIR sensor Alarm log featuring the last 16 alarms Filter monitor with timer factory setting of 90 days Adjustable to 30 90 180 360 days It is possible to purchase Comfort 1200 with pressure controlled filter monitor Bupassine the outdoor air reduces heat recovery enabling the
13. ply air Utresh air textract air tfresh air COMFORT 5000 BY NILAN nt 96 li l N ill i NER iii 1000 2000 3000 4000 5000 q l s 600 800 1000 1200 1400 Sound data Sound data for o 4000 m h and P Sound output level L drops with falling air volume and falling back pressure Sound output level L at a given distance will depend on acoustic conditions in the place of installation Sound output level L Octave band Hz 125 250 gt 00 1 000 2 000 4 000 8 000 Total 2 dB A Surface dB A 47 7 50 6 44 9 43 7 35 7 30 9 e32 53 7 Supply air dB A 61 4 TOT 783 eles 70 4 EAS 84 3 Extract air dB A 48 7 272 54 2 O9 473 33 6 149 60 8 Outdoor air dB A 20 4 29 9 2o 56 4 48 8 35 4 14 6 100 Pa accordine to EN 9614 2 for surfaces and EN 5136 for ducts Discharee air dB A 60 2 58 5 fal 778 78 1 68 0 54 3 82 4 PLANNING Heating elements accessory Water heating element for internal fitting 70 C lt Mixer circuit proposal Tp H WI 5 Se a AP 20kPa The operating panel 152 L9 E NEN e e ee 115 Switch for user choise accessory safety switch Power supply Cee NEUE Quee te ee eo e E eee ee ee eae ee Oe Seo ee et eee eee Mer ee A S DU EIC fed E AAN GAN Supply air TEL TJ IK T4
14. ter The extraction and or supply fan can be operated with the aid of one or two pressure transmitters Water heating element incl regulation The water heating element is designed to be built into the unit and must be con nected to the primary heating supply Supplied with three way adjustment valve temperature sensor and frost thermostat Electrical heating surface incl regulation The electrical heatine surface is supplied ready to fit into the fresh air duct and for easy fitting the device is pre fitted with all the required sensors 15 kW or 21 kW Electrical pre heatine element Frost protection Avoid having to defrost the unit resulting in a loss of power With temperature sensors supplied to be fitted in the ducts 21 kW Top cover If Comfort 5000 is eoine to be installed outside it is possible to order a top cover which protects the unit aeainst rain and snow Shut off damper Damper for external installation with or without sprine return Humidity and CO sensor For demand control ventilation the unit can be integrated with an humidity and Sensor Expansion PLB The expansion PCB provides additional functions for the CTS 60e control Vibration dampers A set of four vibration dampers be included Water trap The water seal is intended for negative pressure and has a ball to ensure that the water seal is tight even when not filled with water Heating cable To protect the condensa
15. tion outlet against frost a3 metre lone self regulating heatine cable can be ordered Pressure reeulateg filter alarm Measures the pressure drop across the filter and alerts when the filter is to be repla 14 DELIVERY assez AND HANDLING Transport and storage Comfort 1200 comes in factory packaging that protects it during transport and storage Comfort 1200 must be stored in a dry place in its original packaging until installation The packaging should only be removed immediately prior to installation Handling and mowine the Comfort 5000 Comfort 5000 is braced with two tracks at the bottom which can be used to move the unit with a lifting truck Installation conditions Durine installation future service and maintenance should be taken into account We recommend a minimum eap in front of the unit of 1 m Theunit must be installed level for the sake of the condensate drain The condensate drain requires clearance of min 12 5 cm under the drain nozzle 1 S Service clearance unit shown from above 15 INFORMATION FROM A T0 Z Nilan develops and manufactures premium quality energy saving ventilation and heat pump solutions that provide a healthy indoor climate and low level energy consumption with the greatest consideration for the environment In order to facilitate each step in the construction process from choosing the solution through to planning installati
Download Pdf Manuals
Related Search