IDS-141_181A User Manual
Contents
1. Load Default Reboot Device Reboot Device Import E sport Configuration Import o Export Figure 5 12 Save Load The following table describes the labels in this screen Save Configuration to Save current configuration into flash memory Flash Load default configuration except the network settings If you want to load all factory Load Default default you need to press Reset button on the device Hardware restore Reboot Device Reboot the device server warm start Import Configuration Restore the previous exported configuration Export Configuration Exported current configuration to a file to backup the configuration Table 5 6 Save Load ORing Industrial Networking Corp 24 e Oring a IDS 181A Series User s Manual 5 1 2 3 Configure serial port Serial Settings Serial Settings Service Mode Notification part Fort Alias Bap 0 Baudrate 38400 Stop Bits 1 Performance Throughput Parity No Flow Control Mo Flo Data Bits g Interface R5232 Delimiter Settings Serial ta Ethernet Ethernet to Serial Delimiter 1 Delimiter 2 Delimiter 3 Delimiter 4 HEX HEX HE HEX Enabled Enabled Enabled Enabled Flush Serial to Ethernet Data Bulfer After L 0 65535 ms The received data will be queueing in the buffer until all the delimiters are matched When the buffer is Full 4K Bytes or after flush S2E data buffer timeout the data2. Service Provider Choose the DDNS service Provider Hostname You must first apply an account from the DDNS service Provider such as www dyndns org then register with the dynamic DNS service Input the fixed hostname you got from the DDNS service A t d Ga Input the Account and Password you have registered from the DDNS service Provider Password Check WAN IP Device will check the IP address Status at interval time you set Schedule Table 5 4 DDNS setting Notification Specify the events that should be notified to the administrator The events can be alarmed by E mail SNMP trap or system log General Security Networking DONS Motification Management Upgrade Firmware Save Load SNMP Settings E mail Settings Syslog Settings Fault LED Relay Settings Notified Items Hardware Reset Cold Start El Software Reset Warm Start Eth 1 Link Down Login Failed E IP Changed Password Changed Access IP Blocked Redundant Power Changed r Power 1 Fault Power 2 Fault M Mm A E RN Trap Server Trap Serverz Trap Servers Trap Serverd i Refresh Apply Only ae Apply and Save Figure 5 9 Notification 21 ORing Industrial Networking Corp Orma IDS 181A Series User s Manual e The following table describes the labels in this screen Fault LED Relay Settings Apply Apply current setting Apply and Save Apply and save current setting Table 5 3 Notification
3. 5 1 DS Tool DS Tool is a powerful Windows utility for DS series lt supports device discovery device configuration group setup group firmware update monitoring functions etc It is easy for you to install and configure devices over the network 5 1 1 Install IDS Tool otep 1 Execute the Setup program click start after selecting the folder for DS Tool 72 D5 Iool Installer Destination Directory C Program FilesD5 T nol Required 7543 E Available 210228 K O Browse Start Exit Figure 5 1 13 ORing Industrial Networking Corp IDS 181A Series User s Manual Step 2 When installation complete successfully then click OK 2 ps Iool Installer Installation was completed successfully UK Figure 5 2 Step 3 Check for your selection The installation of DS Tool is finished x Launch D Tool Mow V Launch D Tool Later Figure 5 3 ORing Industrial Networking Corp 14 oro Os IDS 181A Series User s Manual 5 1 2 Using DS Tool 5 1 2 1 Explore device servers 15 DS Tool will broadcast to the network and search all available DS devices in the network The default IP address of device is 192 168 10 2 and selects the searching device you wish to use and press Add button You can set static IP address or in DHCP client mode to get IP address automatically Finally click OK button to add the device 5 DS Tool File Device Configuration
4. Device Please click Reboot button to restart device Figure 5 34 Save Reboot ORing Industrial Networking Corp 52 ORing e IDS 181A Series User s Manual The following table describes the labels in this screen Load default configuration except settings of Network If you want load all factory default Factory Default you should press Reset button about the five seconds on the device Hardware restore Restore Restore the previous exported configuration Configuration Backup Export the current configuration to a file Configuration Upgrade Firmware Upgrade to a new firmware with specified file Reboot Device Reboot the device server warm start Table 5 20 Save Reboot 5 3 Configuration by SSH Console 5 3 1 Connect to DS You can use SSH Tool e g PUTTY to access SSH console of DS The SSH console interface is shown below login as admin adminBi92 168 0 39 s ERA ORIMG Industrial Serial Device Server Commander LOR LING Industrial Serial Device Server Commander l COvervien j General Settings ji Network Settings Ports settings Security Accessible IP Settings Mortificationi uto Warning Settings Change Password Load Factory Default 2 Save configuration Exit amp Logout Select one function 1 6 C L 5 R uQ Figure 5 35 SSH o3 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e Technical Specifications Network Interfa
5. Factory default is 0 Connect on Startup The TCP Client will build TCP connection once the connected serial device is started Connect on Any The TCP Client will build TCP connection once the connected serial device starts to send Character data Table 5 18 TCP client mode Service Mode UDP Client Mode Compared to TCP communication UDP is faster and more efficient n UDP mode you can Uni cast or Multi cast data from the serial device server to host computers and the serial device can also receive data from one or multiple host Industrial Device Server Service Mode Porti Service Mode UDP Mode lt Listen Port Host start IP Host end IP Send Port 1 0 0 0 0 2 0 0 0 0 3 0 0 0 0 4 o 0 0 0 IR Figure 5 30 UDP client mode 47 ORing Industrial Networking Corp one IDS 181A Series User s Manual e 5 2 1 3 Management Access IP Control Access IP Control Settings allow you to add or block the remote host IP addresses to prevent unauthorized access f host s IP address is in the accessible IP table then the host will be allowed to access the DS You can choose one of the following cases by setting the parameter 1 Only one host with a special IP address can access the device server IP address 255 255 255 255 e g 192 168 0 1 255 255 255 255 2 Hosts on a specific subnet can access the device server IP address 255 255 255 0 e g 192 168 0
6. M UDP Mode UDF Settings Listening Port 14004 pA Auto Scan Multilink Destination Host Begin Destination Host End Sending Port 182 158 0 1 to 1192 168 0 100 110000 mE Auto Scan 2 to eG Auto Scan 3 to eo Auto Scan 4 to e Auto Scan Figure 5 17 UDP mode Notification Specify the events that should be noticed The events can be noticed by E mail SNMP trap or system log ORing Industrial Networking Corp 32 e Oring a IDS 181A Series User s Manual Serial Settings Service Mode Notification Y SNMP Trap e Email Notification Iw Syslog Notificatiori Let beet oT SNMP Settings Email Settings Syslog Settings Notified Items M DCD Changed M CTS Changed M DSR Changed Port Connected Port Disconnected Trap Server Trap Server2 Trap Server3 Trap Server4 i Refresh a Apply Only ae Apply and Save Figure 5 18 Notification The following table describes the labels in this screen When DCD Data Carrier Detect signal changes it indicates that the modem DCD changed connection status has changed Notification will be sent When DSR Data Set Ready signal changes it indicates that the data communication DSR changed equipment is powered off A Notification will be sent When CTS Clear To Send signal changes it indicates that the transmission between CTS changed computer and DCE can proceed A notification will be sent In TCP Serv
7. On button you Device Name location can locate the serial server s position Set SNTP Input the SNTP server domain name or IP address port and select the Time zone ORing Industrial Networking Corp 16 e Oring e IDS 181A Series User s Manual By Clicking the Get current Host button you will get your local IP and then set the Set Auto IP Report Report interval time The device server will report its status periodically Table 5 1 General settings At IP collection option show the device server status The report interval is O indicate disable this setting default But you can set the other IP or Port Security General Security Networking DONS Notification Management Upgrade Firmware Save Load Access IP Table Password IPT 192 168 0 1 Mask 255 255255255 v Enabled New Password IPz 182 168 0 2 Mask 2552552550 Enabled IP3 Mask NENNEN Bi Sess Confirm Mew Password EN j gang us Old Password IP5 EE Mask PO Enabled IPE EE Mask NEN Enabled IP _ cele AAA Enabled Change Password IPS EE Mask EE Enabled IP3 EE Mask EE Enabled IPO Mask PO Enabled i Mask PO FT Enabled IPT 0 Mask a Enabled Pa Mask PO T Enabled IPTA Mask NEED Enabled IPS Mask PO Enabled PRB Mask EE Enabled i Refresh Apply Only Apply and 5ave Figure 5 6 Security The following table describes the labels in this screen Accessible IP Setting To prevent unauthorized
8. You can define max 4 delimiters 00 FF Hex for each way The data will be hold until the delimiters are received or the option Flush Serial to Ethernet data buffer times out 0 means disable Factory default is O Flush Data Buffer After The received data will be queued in the buffer until all the delimiters are matched Ethernet to serial When the buffer is full 4K Bytes or after flush E2S data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds ORing Industrial Networking Corp 42 e ms IDS 181A Series User s Manual Delimiter You can define max 4 delimiters OO FF Hex for each way The data will be hold until the delimiters are received or the option Flush Ethernet to Serial data buffer times out 0 means disable Factory default is 0 Table 5 15 Port Profile Service Mode Virtual COM Mode In Virtual COM Mode the driver establishes a transparent connection between host and serial device by mapping the Port of the serial server serial port to local COM port on the host computer Virtual COM Mode also supports up to 5 simultaneous connections so that multiple hosts can send or receive data by the same serial device at the same time ORing Industrial Device Server Service Mode Porti v Data Encryption O Enable 9 Disable Service Mode Virtual COM Mode v Idle Timeout o 0 65535 seconds Alive Check 0 0 65535 seconds Max Connection 1 max
9. port to hint the connected device 110bps 300bps 1200bps 2400bps 4800bps 9600bps 19200bps Baud rate 38400bps 57600bps 115200bps Data Bits 5 6 7 8 Stop Bits 1 2 1 5 Flow Control No XON XOFF RTS CTS DTR DSR Force TX interval time is to specify the timeout when no data has been transmitted Force TX Interval Time When the timeout is reached or TX buffer is full 4K Bytes the queued data will be sent O means disable Factory default value is 0 Throughput This mode optimized for highest transmission speed Performance Latency This mode optimized for shortest response time Apply Activate settings on this page Table 5 14 Serial configuration 41 ORing Industrial Networking Corp IDS 181A Series User s Manual Port Profile ORing Industrial Device Server Port Profile El El aml Local TCP Port 4000 Command Port 4001 Mode Serial to Ethernet Flush Data Buffer After 0 ms Delimiter Hex 0 ff r Jal Jal Jael Mode Ethernet to Serial Flush Data Buffer After 0 ns Delimiter HexO ff i Jz Jal Jael Apply Figure 5 26 Port Profile The following table describes the labels in this screen Flush Data Buffer After The received data will be queued in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flush S2E data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds Serial to Ethernet Delimiter
10. will also be sent Force T interval time lo 065535 me ta 1 lintenvaltime data 2 lintervaltime data 3 The received data will be queueing in Te buffer until T interval time is timeout or Tz buffer is full 4E Bytes the data will also be sent U is disable i Refresh i Figure 5 13 Serial Settings The following table describes the labels in this screen Port Alias Remark the port to hint the connected device Interface RS232 110bps 300bps 1200bps 2400bps 4800bps 9600bps 19200bps 38400bps 57600bps 115200bps Baud rate Data Bits 5 6 7 8 Stop Bits 1 2 1 5 Parity No Even Odd Mark Space Flow Control No XON XOFF RTS CTS DTR DSR 25 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e Throughput This mode optimized for highest transmission speed Performance Latency This mode optimized for shortest response time Delimiter You can define max 4 delimiters OO FF Hex for each way The data will be hold until the delimiters are received or the option Flush Serial to Ethernet data buffer times out 0 means disable Factory default is O Serial to Ethernet Flush Data Buffer After The received data will be queuing in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flush S2E data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds Delimiter You can define max 4 delimiters OO FF Hex fo
11. 2 255 255 255 0 3 Any host can access the device server Disable this function by un checking the Enable IP Filter checkbox Ring Industrial Device Server Access IP Control List O Enable IP Filtering Not check this option will allow any IP to have assessibility Activate the IP IP Address Netmask AB eg ED EE 9 wees co G VS N o un w N a z Figure 5 31 Access IP ORing Industrial Networking Corp 48 IDS 181A Series User s Manual SMTP SNMP Conf Email Server configuration includes the mail server s IP address or domain If the authentication is required specify your name and password There are 4 Email addresses that you can specify to receive the notification SNMP Server configuration includes the SNMP Trap Server IP address Community Location and Contact There are 4 SNMP addresses you can specify to receive the notification SysLog server configuration includes the server IP and server Port This option need to use with DS Tool Industrial Device Server SMTP SNMP Configuration E mail Settings mter ic Port O L My server requires authentication User Name Password E mail Sender E mail Address 1 E mail Address 2 E mail Address 3 E mail Address 4 SNMP Trap Server SNMP Server 1 SNMP Server 2 SNMP Server 3 SNMP Server 4 Figure 5 32 SMTP SNMP conf
12. COM Configuration Options Help Pal Salil e Broadcast Device SH sp COM d Broadcast Searching EN Sio i p MAC 00 44 B8 CC DD 77 Device List Mew Devices ra a VCOM List AEREA Cinna 1921586102 EE Setup Wizard m A IP Collection le Using Static IP Using DHCP dem C System Log Assign Static IP IP Address f 932 168 10 2 Metmask 255 255 255 0 Gatway 192 168 10 2 DNS DNS2 e Auto Scan Password Cancel Clear All Select All 72 A lot of IPs need to be re config Click here Your best choice Group IP Wizard Figure 5 4 ORing Industrial Networking Corp Orma IDS 181A Series User s Manual e 5 1 2 2 Configure device servers General settings This page includes the setting of device name SNTP server and Auto IP Report General Security Networking DONS Notification Management Upgrade Firmware Save Load Model Power 100 0 LAN IP Address LAN MAC Address Version 3 Locate On Device Name Locatian Devices emer DEFAULT W Using SNTP Time Server le Auto IP Report SMTP Server IP Port IP Address Port pool ntp org 1 23 1 32 158 10 248 160001 Time Zone Get Current Host IBI T 08 0077 aipei r Report Interval 1 U Seconds WY Refresh En Apply Only az Apply and Save Figure 5 5 General settings The following table describes the labels in this screen You can set the device name or related information By clicking Locate
13. IDS 181A Series User s Manual Step 2 Push the IDS 141A IDS 181A toward the Din Rail until you heard a click sound Figure 2 2 2 2 Wall Mounting Installation Each IDS 141A IDS 181A has another installation method for you A wall mount panel can be found in the package The following steps show how to mount the IDS 141A IDS 181A on the wall ORing Industrial Networking Corp 4 IDS 181A Series User s Manual 2 2 1 Mount IDS 141A IDS 181A on wall Step 1 Remove Din Rail kit Figure 2 3 5 ORing Industrial Networking Corp IDS 181A Series User s Manual Step 2 Use 6 screws that can be found in the package to combine the wall mount panel Just like the picture shows below Figure 2 4 The screws specification shows in the following two pictures In order to prevent IDS 141A IDS 181A from any damage the size of screws should not be larger than the size that used in IDS 141A IDS 181A Pozidrive Figure 2 5 ORing Industrial Networking Corp 6 IDS 181A Series User s Manual Hardware Overview 3 1 Front Panel Figure 3 1 1 LED for PWR1 and system status When the PWR1 links the green LED will be light on 2 LED for PWR2 and system status When the PWR2 links the green LED will be light on 3 LED for fault indicator When fault occurred this red LED will be light on 4 LED for Serial ports status When data transmitted the green LED will be light on S5 S8 onl
14. Industrial Device Server User s Manual IDS 141A IDS 181A Version 1 00 December 2009 e Oring e ORing Industrial Networking Corp 3F No 542 2 Jhong Jheng Rd Sindian District New Taipei City 231 48 Taiwan R O C Tel 886 2 2218 1066 Fax 886 2 2218 1014 Website www oring networking com E mail support oring networking com Table of Content GETTING TO KNOW YOUR DEVICE SERVER ii 1 1 1 About the IDS 141A IDS 181A Serial Device Server ee 1 1 2 SONWANE FCAT eT la a 1 Lo Ha Ware FCOMUlOS RE 2 HARDWARE INSTALLATION a a 3 2 1 Install IDS 141A IDS 181A OD DIN Fall iui serre E pee EO HR he eut ea on Eee rts 3 2 1 1 Mount IDS 141A IDS 181A on DIN Radl occcccnnnnnnnnnnccnnnnnnnnnnononononnnnnonnnnnnnnnnnnnnnnnnnnnnnn nn nr nr 3 2 2 Wall ord eu ao leue A E A A AR 4 224 Mount 4DSssI4TA7 IDS IS aT eed ee eli ew eae ede 5 HARDWARE OVER EW A A o te 7 3 1 ETT M M J na 3 2 FONERA W ax Ds Er 8 3 3 SONAS tio T aati s 8 3 4 Bolom AO A A A ie sien A AA AS il 10 CABLES aa iio o ta 11 4 1 Ethernet Cables a tel ed 11 MANAGEMENT INTERFAGE una aa 13 5 1 P STOO ee gu RTE TO aT eR ee eT eee MCN 13 5 1 1 WS tal TO Sol A deco A A hacen eee 13 35422 Hong 152100 accct ies ottenuto ioter e Meee en eee eee 15 LZA Explore device SERV CIS aoo qu oe ed 15 S IRE CA cad 16 KD Contieure senal Por TTT 25 o C
15. Management General Security Networking DONS Notification Management Uparade Firmware Save Load e Web Management Enable Goto Web Management le Telnet Management Enable Goto Telnet Management SNMP Management Settings Community Location o Contact o Trap Server Trap Serverz PO Trap Servers PS Trap Server l E Refresh a Apply Only ae Apply and Save Figure 5 10 Management ORing Industrial Networking Corp 22 amp Oring amp e IDS 181A Series User s Manual The following table describes the labels in this screen To enable management from Web Click Goto Web Management button to Web Management Enable access web Telnet Management Enable To enable management by Telnet SNMP Management Enable To enable management by SNMP SNMP Management Settings To configure SNMP related settings Table 5 4 Management Upgrade Firmware General Security Networking DDNS Notification Management Upgrade Firmware Save Load Firmware Image Browsing Upgrade Figure 5 11 Upgrade Firmware The following table describes the labels in this screen Browse the file and upgrade Upgrade Enable the firmware upgrade Table 5 5 Upgrade Firmware 23 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e Save Load General Security Networking DONS Notification Management Upgrade Firmware Save Load Save Configuration to Flash Load Default
16. ORing Industrial Networking Corp IDS 181A Series User s Manual System Event Conf Specify the events that should be notified to the administrator The events can be alarmed by E mail SNMP trap or system log Industrial Device Server System Event Configuration Device Event Notification Hardware Reset Cold Start SMTP Mail SNMP Trap O Syslog Software Reset Warm Start SMTP Mail J SNMP Trap O Syslog Login Failed O SMTP Mail U SNMP Trap O Syslog IP Address Changed O SMTP Mail C SNMP Trap Syslog Password Changed O SMTP Mail SNMP Trap Syslog Access IP Blocked O SMTP Mail C SNMP Trap O Syslog Redundant Power Changed O SMTP Mail U SNMP Trap O Syslog Port Event Notification Porti Y DCD Changed O SMTP Mail C SNMP Trap Syslog DSR Changed O SMTP Mail C SNMP Trap O Syslog CTS Changed O SMTP Mail U SNMP Trap Syslog Port Connected SMTP Mail O SNMP Trap Syslog Port Disconnected O SMTP Mail C SNMP Trap O Syslog Fault Event Notification and Fault LED Relay Power 1 Fault CI SMTP Mail SNMP Trap C Syslog O Fault LED Relay Power 2 Fault OSMTP Mail SNMP Trap C Syslog O Fault LED Relay Eth1 Link Down SMTP Mail SNMP Trap C Syslog O Fault LED Relay Figure 5 33 SMTP SNMP conf The following table describes the labels in this screen This refers to starting the system from power off contrast this with warm start When Hardware Reset Cold performing a cold start DS will automa
17. PoE Point to Point Protocol over Ethernet Device can use PPPoE mode to connect the Network Input the username and Password then click Connect button If the device has been connected the Status will become the Link up and device will get an IP address from PPPoE server Click Return button return the IP Configuration default page ORing Industrial Networking Corp 38 IDS 181A Series User s Manual Industrial Device Server PPPoE Setting User Name Password Status Link down Connect Disconnect Return Authentication You can set the password to prevent unauthorized access from network Input the Old password and New password to change the password Factory default is no password 39 ORing Industrial Networking Corp IDS 181A Series User s Manual User Authentication Industrial Device Server Apply Figure 5 24 Authentication 9 2 1 2 Port serial setting Serial configuration Serial Configuration Porti industrial Device Server porti RS232 38400 qn 1 v None None v Apply Figure 5 25 Serial configuration ORing Industrial Networking Corp 0 ms 9 Throughput Latency AO amp Oring amp e IDS 181A Series User s Manual The following table describes the labels in this screen Port Alias Remark the
18. WR2 12 48V DC Frame ground PWR 2 1A 24V PWR 1 DC12 48V Figure 3 2 ORing Industrial Networking Corp oran e Oring amp IDS 181A Series User s Manual Cabies 4 1 Ethernet Cables The IDS 141A IDS 181A has standard Ethernet ports According to the link type the IDS 141A IDS 181A use CAT 3 4 5 5e UTP cables to connect to any other network device PCs servers switches routers or hubs Please refer to the following table for cable specifications 10BASE T Cat 3 4 5 100 ohm UTP 100 m 328 ft RJ 45 100BASE TX Cat 5 100 ohm UTP UTP 100 m 328 ft RJ 45 Table 4 1 Cable Types and Specifications 100BASE TX 10BASE T Pin Assignments With 100BASE TX 10BASE T cable pins 1 and 2 are used for transmitting data and pins 3 and 6 are used for receiving data 11 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e TO TT Table 4 2 RJ 45 Pin Assignments The IDS 141A IDS 181A supports auto MDI MDI X operation You can use a straight through cable to connect PC to IDS 141A IDS 181A The following table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs peas mae maan s Rega 09 mem Mh Table 4 2 MDI MDI X pins assignment Note and signs represent the polarity of the wires that make up each wire pair ORing Industrial Networking Corp 12 e ORing IDS 181A Series User s Manual Management Interface
19. access by setting host IP addresses and network masks You can set the password to prevent unauthorized access from your server Factory Password setting default is no password Table 5 2 Security 17 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e Network Setting Device DS can connect the Network by wire a You must assign a valid IP address for DS before attached in your network environment Your network administrator should provide you the IP address and related settings The IP address must be unique within the network otherwise DS will not have a valid connection to the network You can choose from three possible IP configuration modes Static DHCP BOOTP The Factory Default IP address is 192 168 10 2 General Security Networking DONS Notification Management Upgrade Firmware Save Load ie Using Static IP Using DHCPYBOOTP Static IP Settings IPAddess 92168102 Metmask 255 255 255 0 Gateway 92168101 DN51 192168101 DNS2 OO lf Refresh En Apply Only Apply and Save Figure 5 7 Network Setting The following table describes the labels in this screen Using DHCP BOOTP IP Address automatically assigned by a DHCP server in your network Static IP Address Manually assigning an IP address Subnet Mask All devices on the network must have the same subnet mask to communicate on the ORing Industrial Networking Corp 18 e Oring e IDS 181A Series Use
20. at the same time ORing Industrial Networking Corp 44 e ms IDS 181A Series User s Manual Ing Industrial Device Server Service Mode Porti Data Encryption O Enable Disable Service Mode TCP Server Mode TCP Server Port 4000 Idle Timeout 0 0 65535 seconds Alive Check 0 0 65535 seconds Max Connection iB max connection 1 5 Figure 5 28 TCP Server Mode The following table describes the labels in this screen TCP Server Port Set the port number for data transmission When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts 0 Idle Timeout indicate disable this function Factory default value is O If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not alive Alive Check the connection will be closed and the port will be freed 0 indicate disable this function Factory default is O The number of Max connection can support simultaneous connections are 5 default values Max Connection is 1 Table 5 17 TCP server mode 45 ORing Industrial Networking Corp IDS 181A Series User s Manual e Service Mode TCP Client Mode In TCP Client Mode device can
21. ce 10 100Base T X which support Redundant Dual Ethernet or Ethernet Switch Mode support Auto recover less than 10ms connector RJ 45 Protection Built in1 5KV magnetic isolation ICMP IP TCP UDP DHCP BOOTP ARP RARP DNS SNMP MIB Il HTTPS SSH Protocols Serial Interface 4x RS232 IDS 141A 8x RS232 IDS 181A Interface Connector DB62 Female Serial Baud Rate 110 bps to 115 2 Kbps Built in16KV ESD protection Serial Line Protection 2KV DC isolation for each port PWR Ready 1 Green On DC power 1 activated Green Blinking System booting Located by Administrator ETH Link ACT Green ON Blinking 10 Mbps Ethernet LED Indicators Green amp Amber ON Blinking 100 Mbps Ethernet ORing Industrial Networking Corp 94 IDS 181A Series User s Manual Serial TX RX LEDS Green Serial port is transmitting receiving data Fault Fault alarm Amber Power Requirements Power Input Reverse Polarity Protection Power Consumption PWR1 2 12 48VDC in 6 pin Terminal Block Present at terminal block 7 Watts MAX Software Utility Utility Serial Mode Multiple Link DS Tool for Windows NT 2000 XP 2003 VISTA which include Device discovery Auto IP report Device setting Access control list Group setting Device monitoring Serial port monitoring Log info Group Firmware update Virtual Com TCP Server TCP Client UDP Serial Tunnel TCP Alive Check Timeout Inactivity T
22. connection 1 5 Figure 5 27 Virtual COM mode The following table describes the labels in this screen Idle Timeout When serial port stops data transmission for a defined period of time Idle Timeout the 43 ORing Industrial Networking Corp e ORIng IDS 181A Series User s Manual e connection will be closed and the port will be freed and try to connect with other hosts O indicate disable this function Factory default value is 0 f Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not Alive Check alive the connection will be closed and the port will be freed 0 indicate disable this function Factory default is O The number of Max connection can support simultaneous connections are 5 default Max Connection values is 1 Table 5 16 Virtual COM mode Not allowed to mapping Virtual COM from web Service Mode TCP Server Mode In TCP Server Mode DS is configured with a unique Port combination on a TCP IP network In this case DS waits passively to be contacted by the device After the device establishes a connection with the serial device it can then proceed with data transmission TCP Server mode also supports up to 5 simultaneous connections so that multiple device can receive data from the same serial device
23. er Mode when the device accepts an incoming TCP connection this event will be trigger In TCP Client Mode when the device has connected to the remote host Port connected this event will be trigger In Virtual COM Mode Virtual COM is ready to use A notification will be sent In TCP Server Client Mode when the device lost the TCP link this event will be trigger Port disconnected In Virtual COM Mode When Virtual COM is not available this event will be trigger A notification will be sent Table 5 11 Notification 33 ORing Industrial Networking Corp IDS 181A Series User s Manual 5 2 Configuration by Web Browser 5 2 1 CONNECT TO THE WEB PAGE Step 1 Input the IP address of DS with https 192 168 10 2 in the Address input box of IE Step 2 Click Yes button on the dialog box Security Alert Information you exchange with this site cannot be viewed or changed by others However there is a problem with the site s security certificate amp The security certificate was issued by a company you have not chosen to trust View the certificate to determine whether you want to trust the certifying authority The security certificate date is valid amp The name on the security certificate is invalid or does not match the name of the site Do you want to proceed Figure 5 19 Certificates ORing Industrial Networking Corp 34 e ms e IDS 181A Series User s Manual Step 3 Input the na
24. establish a TCP connection with server by the method you set Startup or any character After the data has been transferred device can disconnect automatically from the server by using the TCP alive check time or Idle timeout settings Ring Industrial Device Server Service Mode Es E El Porti v E or z Data Encryption OEnable 9 Disable Service Mode TCP Client Mode vi Destination Host Idle Timeout o 0 65535 seconds Alive Check o 0 65535 seconds Connect on 9 Startup Any Character Destination Host Port 2 A ID Figure 5 29 TCP client mode The following table describes the labels in this screen Destination Host Set the IP address of host and the port number of data port When serial port stops data transmission for a defined period of time Idle Timeout the Idle Timeout connection will be closed and the port will be freed and try to connect with other hosts 0 indicate disable this function Factory default value is 0 If Multilink is configured only ORing Industrial Networking Corp 46 e ms IDS 181A Series User s Manual AS the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not alive Alive Check the connection will be closed and the port will be freed 0 indicate disable this function
25. hrough User can manage IDS 141A IDS 181A through NAT router m Redundant Power Inputs 12 48VDC on terminal block amp power jack B Redundant multiple host devices 5 simultaneous in Virtual COM TCP Server TCP Client mode and 4 simultaneous for UDP mode i Secured Management by HTTPS and SSH m Versatile Modes Virtual Com Serial Tunnel TCP Server TCP Client UDP m Event Warning by Syslog Email SNMP trap Relay m X Various Windows O S supported Windows NT 2000 XP 2003 VISTA 32bits ORing Industrial Networking Corp IDS 181A Series User s Manual 1 3 Hardware Features E Redundant Power Inputs 12 48 VDC on terminal block and power jack m Operating Temperature 40 to 70 C m Storage Temperature 40 to 85 C E Operating Humidity 596 to 9596 non condensing E Casing IP 30 u One 10 100Base T X Ethernet port m X Dimensions W x D x H 26 1 W x 94 9 D x 144 3 H mm ORing Industrial Networking Corp e e Oring e IDS 181A Series User s Manual Hardware Installation 2 1 Install IDS 141A IDS 181A on DIN Rail Each IDS 141A IDS 181A has a Din Rail kit on rear panel The Din Rail kit helps IDS 141A IDS 181A to fix on the Din Rail It is easy to install the IDS 141A IDS 181A on the Din Rail 2 1 1 Mount IDS 141A IDS 181A on DIN Rail Step 1 Slant the IDS 141A IDS 181A and mount the metal spring to Din Rail Metal Spring Figure 2 1 3 ORing Industrial Networking Corp
26. imeout Delimiter for Data Packing Force TX Timeout for Data Packing 5 Hosts simultaneous connection Virtual Com TCP server TCP Client UDP VCOM Driver Windows NT 2000 XP 2003 VISTA Configuration Web HTTPS console SSH console Console Command DS Tool for Windows NT 2000 XP VISTA Environmental 55 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e Operating Temperature 40 70 C 40 to 158 F Operating Humidity 5 to 95 Non condensing Storage Temperature 40 to 85 C 40 to 185 F Dimensions W x D x H 26 1 W x 94 9 D x 144 3 H mm r Casing IP 30 protection Regulatory Approvals Shock IEC 60068 2 27 Free Fall IEC 60068 2 32 Vibration IEC 60068 2 6 EMI FCC Part 15 CISPR EN55022 class A EN61000 4 2 ESD EN61000 4 3 RS EN61000 4 4 EFT EN61000 4 5 Surge EN61000 4 6 CS EN61000 4 8 EN61000 4 11 Warranty ORing Industrial Networking Corp 96
27. ironment Your network administrator should provide you with the IP address and related settings The IP address must be unique and within the network otherwise DS will not have a valid connection to the network You can choose from three possible IP configuration modes Static DHCP BOOTP The Factory Default IP address is 192 168 10 2 Industrial Device Server IP Configuration IP Configuration Static Y IP Address 1192 168 10 2 Netmask 1255 255 255 0 Gateway 192 168 10 1 DNS Server 1 192 168 10 1 DNS Server 2 s Auto IP Report Auto Report to IP Auto Report to TCP Port o Auto Report Interval 0 seconds Figure 5 23 IP configuration 37 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e The following table describes the labels in this screen DHCP BOOTP Obtain the IP address automatically from DHCP server Static IP Address Assigning an IP address manually Subnet Mask Set the subnet mask to communicate on the network Enter the IP address of the router in you network DNS Server Enter the IP address of the DNS server to translate domain names into IP address The device server will report its status periodically At DS Tool gt IP collection option Auto IP Report show the device server status The report interval is O indicate disable this setting default But you can set the other IP or Port Table 5 13 IP configuration PPPOE setting PP
28. me and password then click OK Connect to 192 168 10 2 cgi bin User name E admin Password Remember my password Figure 5 20 Certificates Only if password is set Step 4 The system information will be shown as below Industrial Device Server System Information IP Address 192 168 10 2 00 00 56 04 02 07 Figure 5 21 System information 35 ORing Industrial Networking Corp ore IDS 181A Series User s Manual rg 5 2 1 1 System Time SNTP Industrial Device Server SNTP Configuration Name DeviceServer DEFAULT Time SNTP O Enable 9 Disable Time Zone GmT 08 00 Taipei E Local Time Sat Dec 26 09 53 44 2009 Time Server pool ntp org Port 1123 Console Telnet Console Enable O Disable Figure 5 22 Time SNTP The following table describes the labels in this screen You can set the name of DS SNTP Enable the SNTP server After you set the SNTP enable select the time zone you located Input SNTP server domain name or IP address and Port Telnet Console SSH is included for security reasons In some cases you may need Console to disable this function to prevent unauthorized access from internet The factory default is enable Table 5 12 Time SNTP ORing Industrial Networking Corp 36 e nrc IDS 181A Series User s Manual IP Configuration You must assign a valid IP address for DS before attached in your network env
29. onnection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not Alive Check alive the connection will be closed and the port will be freed 0 indicate disable this function Factory default is O The number of Max connection can support simultaneous connections are 5 default Max Connection values is 1 Table 5 9 TCP Server mode 29 ORing Industrial Networking Corp e ORIng IDS 181A Series User s Manual e Service Mode TCP Client Mode In TCP Client Mode device can establish a TCP connection with server by the method you have settled Startup or any character After the data has been transferred device can disconnect automatically from the server by using the TCP alive check time or Idle time settings Serial Settings Service Mode Notification port Semice Mode TCF Client Mode TCP Client Mode TCP Client Settings Misc Destination Host Furl Idle Timeout E 0 655535 Seconds 182 168 0 10 4002 BEA Auto Scan Alive Check p 0468535 Seconds Enable Control Port 4003 Connect on Sap Multilink Destination Host Part 1 pA Auto Scan 2 e Auto Scan 3 eG Auto Scan 4 e Auto Scan Figure 5 16 TCP Client mode The following table describes the labels in this screen Destination Host Set the IP address of hos
30. onngurauomDy VWVebJBIOWSBE aiio irt dead 34 32 1 Connect to TAE WED pape 2 e eo Hee e MU MEE eA IULII LEE 34 5 2 1 1 A E A OT E O E ra E A 36 A Port serial Seti esca aaa aia 40 LES MA A leds In a 48 5 2 1 4 TR A MIL M EM DM EM EE MEMO VEN ME ent TONE DOERR OTR RL Om EOS 52 ome IDS 181A Series User s Manual 53 Configuration Dy SSH CORSO A a ta iia 53 5 3 1 Connect to DS TECHNICAL SPECIFICATIONS iria 54 IDS 181A Series User s Manual Getting to Know Your Device Server 1 1 1 2 About the IDS 141A IDS 181A Serial Device Server IDS 141A IDS 181A is an innovative 4 amp 8 ports RS232 to LAN device server Users are able to configure IDS 141A IDS 181A by DS Tool via LAN port IDS 141A IDS 181A offers many powerful features for HW amp SW redundant functions IDS 141A IDS 181A can simultaneously transfer data into 5 host PCs This feature can assure all critical data that saved in different host PCs to avoid Ethernet break or host PCs failure Secondly the IDS 141A IDS 181A provides dual redundant power inputs on terminal block IDS 141A IDS 181A also provides NAT pass through function so that users are able to manage IDS 141A IDS 181A inside or outside the NAT router It is easy for different IP domain users to use IDS 141A IDS 181A Therefore IDS 141A IDS 181A is the best communication redundant solution for current application of serial devices Software Features i NAT pass t
31. r each way The data will be hold until the delimiters are received or the option Flush Ethernet to Serial data buffer times out 0 means disable Factory default is 0 Ethernet to Serial Flush Data Buffer After The received data will be queuing in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flushE2S data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds ORing Industrial Networking Corp 26 ORing IDS 181A Series User s Manual Force TX interval time is to specify the timeout when no data has been transmitted Force TX Interval Time When the timeout is reached or TX buffer is full 4K Bytes the queued data will be sent O means disable Factory default value is 0 Table 5 7 Serial settings Service Mode Virtual COM Mode In Virtual COM Mode The driver establishes a transparent connection between host and serial device by mapping the Port of the serial server serial port to local COM port on the host computer Virtual COM Mode also supports up to 5 simultaneous connections so that multiple hosts can send or receive data by the same serial device at the same time Serial Settings Service Mode Notification port Service Mode Virtual COM Mode Virtual COM Mode Virtual COM Settings Misc Data Fott Janno Edit IF Port Number Idle Timeout lo 0 555 35 Seconds Control Porti 4005 dd Map Virt
32. r s Manual IN e Enter the IP address of the router in you network Enter the IP address of the DNS server The DNS server translates domain names into DNS Server IP address Table 5 3 Network setting PPPoE PPPoE Point to Point Protocol over Ethernet Device can use PPPoE mode to connect the Network Input the username and Password then click Connect button If the device has been connected the Link Status will become the Link up and device will get an IP address from PPPoE server Click Disconnect button to disconnect the PPPoE connection wire PPPoE PPPoE Setting User Mame Password Link Status Link down Disconnect amp Refresh ae Apply Only an Apply and Save Figure 5 8 PPPoE Setting 19 ORing Industrial Networking Corp IDS 181A Series User s Manual DDNS The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname allowing your computer to be more easily accessed from various locations on the Internet General Security Networking CONS Notification Management Upgrade Firmware Save Load DONS Setting Service Provider ezip Hostname lo Account a Password E lo lo Check WAN IP Schedule Ever Hour Start at Maun Kr anal wow ees Figure 5 8 DDNS Setting ORing Industrial Networking Corp 20 e Oring e IDS 181A Series User s Manual The following table describes the labels in this screen
33. t Port Set the port number of data port ORing Industrial Networking Corp 30 e Oring amp e IDS 181A Series User s Manual When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to Idle Timeout connect with other hosts 0 indicate disable this function Factory default value is O If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection Ifthe TCP Alive Check connection is not alive the connection will be closed and the port will be freed O indicate disable this function Factory default is 0 The TCP Client will build TCP connection once the connected serial device is Connect on Startup started Connect on Any The TCP Client will build TCP connection once the connected serial device Character starts to send data Table 5 10 TCP Client mode Service Mode UDP Mode Compared to TCP communication UDP is faster and more efficient n UDP mode you can Uni cast or Multi cast data from the serial device server to host computers and the serial device can also receive data from one or multiple host 31 ORing Industrial Networking Corp ORing IDS 181A Series User s Manual e Seral Settings Service Mode Notification part Service Mode UDP Made
34. t allowed to mapping Virtual COM from web Service Mode TCP Server Mode In TCP Server Mode DS is configured with a unique Port combination on a TCP IP network In this case DS waits passively to be contacted by the device After a connection is established it can then proceed with data transmission TCP Server mode also supports up to 5 simultaneous connections so that multiple device can receive data from the same serial device at the same time ORing Industrial Networking Corp 28 e Oring a IDS 181A Series User s Manual enal Settings 32MYICE Mode Natiication Jort Service Made TCP Server Mode ka LP Server Mode TCP Server Settings Misc Data Port 14002 S Bae Cage Idle Timeout o 0 655435 Seconds Control Port 4003 Alive Check o 0 655535 Seconds Multilink May Connections 1 i Refresh Destinatian Host Y JO Pies Y JO Press OO J JO Bisco PY JO 2 amp Refresh Apply Only Apply and Save Figure 5 15 TCP Server mode The following table describes the labels in this screen Data Port Set the port number for data transmission Scan the data port automatically When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts Idle Timeout O indicate disable this function Factory default value is 0 If Multilink is configured only the first host c
35. tically issue an Auto warning message by Start sending E mail log information or an SNMP trap after booting ORing Industrial Networking Corp 50 amp Oring amp e IDS 181A Series User s Manual This refers to restart the computer without turning the power off When performing a Software Reset Warm warm start DS will automatically send an E mail log information or SNMP trap after Start reboot When an unauthorized access from the Console or Web interface a notification will be Login Failed sent IP Address Changed When IP address of device changed a notification will be sent Password Changed When password of device changed a notification will be sent Access IP Blocked When the host accesses the device with blocked IP addresses a notification will be sent Redundant Power When status of power changed a notification will be sent Change Redundant Ethernet When status of Ethernet port changed a notification will be sent Change DCD changed When DCD Data Carrier Detect signal changes it indicates that the modem connection status has been changed A Notification will be sent DSR changed When DSR Data Set Ready signal changes it indicates that the data communication equipment is powered off A Notification will be sent CTS changed When CTS Clear To Send signal changes it indicates that the transmission between computer and DCE can proceed A notification will be sent Port connected In TCP Ser
36. ual COM Alive Check lo 0 65535 Seconds Multiink l Select a Virtual COM Name Max Connections S Destination Host COM Name 1 Waiting Far COM connect 2 Waiting Far COM connect 3 Waiting Far VELIM connect 4 Waiting Far CO connect 8 Waiting Far COM connect YOCOM Validated charaters of virtual COM name 15 4 2 az and 0 9 Max Length of the name 15 128 charaters Using Traditional COM N arme Figure 5 14 Virtual COM 27 ORing Industrial Networking Corp e ORing IDS 181A Series User s Manual e The following table describes the labels in this screen Map Virtual COM Select a Virtual COM Name to map on The number of Max connection can support simultaneous connections are 5 default Max Connection values is 1 When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts O Idle Timeout indicate disable this function Factory default value is O If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not alive Alive Check the connection will be closed and the port will be freed 0 indicate disable this function Factory default is O Table 5 8 Virtual COM No
37. ver Mode when the device accepts an incoming TCP connection this event will be trigger In TCP Client Mode when the device has connected to the remote host this event will be trigger In Virtual COM Mode Virtual COM is ready to use A notification will be sent Port disconnected In TCP Server Client Mode when the device lost the TCP link this event will be trigger In Virtual COM Mode When Virtual COM is not available this event will be trigger A notification will be sent Power 1 Fault When Power 1 Fault a notification will be sent and the Fault LED will be lighted Power 2 Fault When Power 2 Fault a notification will be sent and Fault LED will be lighted 91 ORing Industrial Networking Corp IDS 181A Series User s Manual Eth link down When Eth link down a notification will be sent and Fault LED will be lighted Table 5 19 System event conf 5 2 1 4 Save Reboot Industrial Device Server Factory Default Reset to default configuration Click Reset button to reset all configurations to the default value Restore Configuration You can restore the previous saved configuration to Device Server File to restore A Backup Configuration You can save current EEPROM value from the Device Server as a backup file of configuration Upgrade Firmware Specify the firmware image to upgrade Note Please DO NOT power off this device while upgrading firmware Firmware UE Reboot
38. y available for IDS 181A 5 LED for Serial ports status When data transmitted the green LED will be light on 85 88 T ORing Industrial Networking Corp Orma IDS 181A Series User s Manual e only available for IDS 181A 6 DB62 Female port 7 Reset button press for 10 sec for factory default 8 10 100Base T X Ethernet port 3 2 Front Panel LEDS The following table describes the labels that stick on the IDS 141A IDS 181A E Blinking System Booting Located by administrator Serial port is transmitting receiving S1 S8 Green Blinking data S5 S8 only available for IDS 181A Green Amber On Blinking 100Mbps LNK ACT ETH Green Amber Green On Blinking 10Mbps LNK ACT Table 3 1 Front panel LEDs 3 3 Serial Ports There 8 serial ports on the front panel of IDS 141A IDS 181A shown as below ORing Industrial Networking Corp 8 O26 6 9 D DLE 5 R e 0 P Ore D De D o ove O O De amp D 52 RTSZ 4 RTS3 D D DS 7 D RXD DSR E DCD6 D T TR D 1 2 3 4 9 6 T 8 9 IDS 181A Series User s Manual S5 S8 only available for IDS 181A Table 3 2 Pin assignment ORing Industrial Networking Corp IDS 181A Series User s Manual 3 4 Bottom Panel The bottom panel components of IUSB 9041 are shown as below 1 2 3 4 5 Terminal block includes PWR1 12 48V DC Relay output 1A 24VDC Terminal block includes PWR2 12 48V DC Power Jack include P
Download Pdf Manuals
Related Search