Manual - OKINA USA
Contents
1. With keyboard 9 5 Enter 2 X 9 Enter With keyboard Shot 9 5 Enter 2 X Shot 9 Enter 3 Axis In case a DVR is used for operating the OSD select go to preset 95 or 2 X go to preset 9 Please refer to the DVR s operation manual for more details Note that in some situations itis not possible to access the OSD menu 1 The dome is running a tour 2 Performing PTZ operations 3 Dome is receiving a command other than OSD request from the keyboard To solve this inability stop the operation and try again Main menu and navigation After entering the OSD Menu the screen will show menu items the controller s joystick to navigate the Main Menu menu s main and sub items by moving in the desired direction The angle mark on the beginning of every item SYSTEM SETTING indicates the selection CAMERA SETTING FUNCTION SETTING DOWN Moving between current menu items WINDOW BLANKING gt Changing the value in sub items ALARM RIGHT Enter the selected menu item EXIT Confirm the value change and return to item selection LEFT Exit from sub menu For more inforamtion please refer to the illustration on the next page for the OSD Menu structure Symbols and indicator p Cursor Sub item is selected use up or down to change value This item has subitem s Some pro2. 4 gt Telemetric control Alarm I O camera setup A AC 230V RS 485 Power input Indoor power adaptor 21 High Res AC 230V to AC 24V security monitor AC 24 Power supply d Professional Real time 16 Channel DVR AC 230V Power input gt Video signal RS485 cable The telemetric control of the appliance uses RS485 serial communication with half duplex transmission technology Depending on the cable type and baud rate the transmission distance could vary The following table shows max distances based on cable with 0 56mm 24AWG twisted pair Due the environmental interferences such as eletromagnetic and induction fields or number of connected appliance on the RS485 bus the transmission range may decrease 9600 bps 19200 bps 6 Some products may not be available in your country please contact our distributor for more details 4 INSTALLATION RS485 Termination Devices using RS485 control are usually connected in daisy chain which requires termination with 120Q resistor on both ends The following graphic illustrates the connection methods Please note that a daisy chain connection type shall not exceed 7 meters RS 485 1202 Resistor 1202 RS 485 Resistor Device 1 Device 2 Device 3 The speed dome series provide an integrated termination switch It should be turned ON on the dome serving as the last device If a controller keyboard is used you also need to turn the termination ON on the key
3. E EE E EI EDO LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE 9 SpeclficatiolS c ee tu ce Erie 2 25 LIMITS ARE DESIGHEND TO PROVIDE REASONABLE PROTECTION AGAINST HAMRFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENGERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS S AUTHORITY TO OPERATE THE EQUIPMENT CE COMPLIANCE STATEMENT WARNING THIS IS A CLASS A PRODUCT IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES CAUTION BEFORE ATTEMPTING TO CONECT OR OPERATE THIS PRODUCT PLEASE READ THE LABEL ON THE BOTTOM AND USER S MANUAL CAREFULLY Technical specification are subjects to change without prior notification Manual may contain mistakes or print errors All trade marks mentioned belong to their respective owners Refer all work related to the installaion of this product to qualified service personnel or system installer
4. kami bami kami kami bami kami bami kami bami kami kasi bami bami bami bami bami kami bami bami kami kami kami kami bami bami bami ee cel eo o ojo ojo o ojojojo jojo o jo o jo ojojojojojojojoij i i I 1 HILDA OOO CO OY 2J2 c o ojojojojio c Blee e elie i n e e e e e e e e e e e e j J gt S QI OL Ol RI aa OI OI MI RI OI OJ OO T r olol EI oo Blo cJ SI SI Ho ol WIcoI oI ico i Iicoci i w myo 37 45 LS wm co SH SH Loj Lo Model SEMW36HB VT53DN Signal Format Image Sensor NTSC 1 4 Sony Exview HAD CCD Resolution DSP Video Signal 530 TV Lines Wide Dynamic Range Sony 1 0V p p Sync Negative Y C Output Zoom Scanning System Progressive Minimum Illumination Day 1 4 Lux 1 50 0 1 Lux 1 3 Night 0 01 Lux 1 3 Mechanical IR Cut Filter I CR Yes 36x Optical Zoom 12x Digital Zoom White Balance Electronic Shutter Speed Lens 3 4mm 122 4mm Lens F1 6 F4 5 Tamron Lens Made in J apan View Angle 48 Wide End 2 8 Tele End S N Ratio More than 50dB Focus Auto Manual Auto Manual ATW Indoor Outdoor One Push WB Manual WB 1 1 10 000 sec Iris Control Gain Control Auto Manual Auto Slow Shutter Auto Manual 3 to 28dB 2dB steps 16 steps Pan Speed Pan Range Tilt Speed Tilt Rang
5. standard limit is 40 C Clear You can clear setting s memory or reset the camera to factory default The follwing functions are supported Clear all zones Clear all presets Clear all patterns Clear all tours Clear all windows Factory defaults Warning The clear action cannot be undone Once an item is cleared it is impossible to retrieve the deleted setting Please make sure that the requested clear action is desired Password setup You can change password to access the OSD menu Default Password is 000000 14 Some products may not be available in your country please contact our distributor for more details Some products may not be available in your country please contact our distributor for more details 6 0SD Camera Setting CAMERA SETTING i ZOOM SPEED DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER ON IR CUT FILTER AUTO LINE SYNC OFF WDR MODE ON ADVANCE SETTING BACK EXIT ADVANCE SETTING AE MODE AUTO SHUTTER N A IRIS N A BRIGHT N A WB MODE AUTO R GAIN N A B GAIN N A HI RESOLUTION OFF BACK EXIT Camera Setting In the camera setting menu you can access camera module related settings Please note that depending on module s capability some functions may not be available Please contact your local sales representative for detailed information ZOOM SPEED Defines the speed in which zoom functions are performed DIGITAL ZOOM Activates or deactivates the
6. 9596 copper The following table shows different cable types and their maximum length The values are for reference only Depending on the qualiy tof the cable and 229m 750 ft environmental conditions the 305m 1000 ft transmission distance might decrease 457m 1500 ft If the cable length is more than 400 m it is recommended to use optional accessories such as video amlifiers or twisted pair video converters to amplify the video signal Max Distance m ft Up to 750m coaxial cable Video Amplifier optional Real time OVR Center Extend connection distance with optional video amplifier Up to 1200m twisted pair or cat 5 cable ji transmitter optional et n High Res Monitor optional optional Real time OVR Center Extend connection distance with Twisted Pair optional video converter Some products may not be available in your country please contact our distributor for more details 4 INSTALLATION Installing the core unit to base board The core units and base boards are packed seperatly in order to protect them during transportation After unpacking and during the installation the core unit should be installed as follows Installing the core unit by inserting it into the housing Please note the position of 1r the connector For releasing please press the lever lock to core and pull off the unit Connector Interface Once the base board is c
7. ERNS TOUR gt ZONES BACK EXIT PRESETS PRESET NUMBER 001 SET PRESET SHOW PRESET CLEAR PRESET EDIT PRESET LABEL BACK EXIT EDIT PRESET LABEL SCAN SCAN NUMBER 01 SCAN SPEED 63 SET LEFT LIMIT SET RIGHT LIMIT CLEAR SCAN RUN SCAN EDIT SCAN LABEL BACK EXIT Function Setting In function setting menu you can define and activate different PTZ funcitons such as preset points auto scan tours and patterns Presets and tour functions can also be set or activated directly from the keyboard without entering the OSD Menu Please refer to the keyboard s manual for operation details Presets PRESET NUMBER supports up to 128 presets The number can be selected from 0 to 128 SET PRESET Defining the preset points directly in OSD by entering this menu item and move the PTZ Press IRIS OPEN key on the keyboard to save If the preset is pointed within digital zoom it will automatically go back to the max optical zoom range in order to provide the best image quality SHOW PRESET Moves to the current preset point CLEAR PRESET Clears the current preset EDIT PRESET LABEL For the current preset you can define a name which will be displayed on the operation screen once the preset is called Please choose the preset number first The avaialbe characters are 0 9 A Z lt gt and space Scan The SCAN function moves the PTZ between 2 predefined points with constant speed The following pa
8. OKINAGs SEMW36HB V53DN 36x Wide Dynamic High Speed Tracking PTZ Camera UserManual English v2 33 WARNING CONTENTS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR 1 PrecaUut On L L L LELE k 1 OTHER OPENINGS ON THE EQUIPMENT 2 Fealt les nee ya he fedet 2 9 Packing lS MORE HOS 3 4 Installatigpniz yy siz nezan ee EEO 4 CAUTION This symbolindicates hat dangerous 5 Operating the Speed 10 RISK OF ELECTRIC SHOCK voltage constituting a risk of electric NOS BD 11 DO NOT OPEN a present wigan ihis unit Map 12 System SEU O kan d ran n ND H2N 13 CAUTION TO REDUCE THE RISK Motion Clear 14 OF ELECTRIC SHOCK DO NOT Camera SOWING TS 15 USER SERVICEABLE PARTS im nandin Preset SCAM ss n E UM a a AR VENE Cau a 16 INSIDE JUST QUALIFIED portant operat ng and ma ntenance SERVICE PERSONNEL SHOULD instructions in the literature Platterns Tours seeeesseme 17 SERIVICE THE PRODUCT accompanying this unit Zones and Privacy Mask 18 Alarm Setting kk 19 FCC COMPLIANCE STATEMENT ee 2 FCC INFORMATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE 5 ress pones te
9. board Please refer to the keyboard s manual for details RS 485 Termination on Termination Termination Termination on off off How to turn termination ON on the speed dome The termination switch is located on the rear side of the connection board For turning it ON open theconnector board How to open the connector board The connector board can be opened by holding the metal clip and pulling Metal Clip holder Jumper Press the metal clip in and pull the board in the outlined direction Hume TE 2 Ta ON ON OFF on rd Term Off default OFF me products may not be available in your country please contact our distributor for more details 4 INSTALLATION Star Connection The star form connection is a popular way to connect different devices It enables longer distance connection of different dome cameras It is recommended to use RS485 distributor to ensure the telemetric data transmission The advantage of star connection is that every channel can work independently and supports a cable length up to 1000 meters depending on the quality of the cable In case more dome cameras are installed the star connection can be extended with Termination additional RS485 distributors activated on every end RS485 cable up to 1000m per channel Video Cable Coaxial cable with 75Q impedance with copper conductor at the center and shielded with
10. butor for more details 4 INSTALLATION Connector description RED AC 24V Power BLACK AC 24V Connector To power supply YELLOW RS485 GREEN RS485 RS 485 Connector To keyboard or DVR devices for m RJ 11 telemetric control Inner Conn Signal lt r Outer Conn Ground Video output Video Output to monitor or DVR BNC RED Alarm input 1 PINK Alarm input 2 YELLOW Alarm input 3 GREEN Alarm input 4 BLACK COM WHITE Alarm output N O Alarm I O A BLUE Alarm output N C AQUA N C 2 BROWN N O 2 GRAY Alarm input 7 PURPLE Alarm input 6 TT ORANGE Alarm input 5 Alarm 1 0 B l O interface to additional alarm sensor or control devices 4 INSTALLATION Some products may not be available in your country please contact our distributor for more details Using optional accessories The speed dome camera series can be connected to various optional accessories through the standard connector types which simplifiy the cable handling and avoid possible mistakes All accessories are tested for max Compatibility and best performance Outdoor power adaptor box 3 Axis keyboard AC 230V to AC 24V controller AC 24 Power supply RS 485
11. camera module s digital zoom function BLC MODE Selects the Back Light Compensation mode which improves the image when an object has strong back light SLOW SHUTTER Activates the Slow Shutter function of the camera which provides a higher light sensibility in low lit environments IR CUT FILTER Enables the removal of Infrared Cut Filter IRC also known as DAY NIGHT mode Enabling the IRC the camera turns into Black White mode and has higher sensibility to low light situations or turns on the IR light depending on the light condition Selectable between On Off orAuto Only available on camera modules with IRC function LINE SYNC Enables and disables Line Synchronization Advanced Setting Under the advanced setting you can make improvements to the image quality depending on different environmental conditions AE MODE Auto Exposure mode Depends on the light condition in the surveillance area you can setthe AE in different modes and adjust the parameters such as shutter speed iris factor and brightness for the best image quality WB MODE White Balance mode an image improvement based on DSP processing You can also adjust the Red Gain or Blue Gain to change the color tone Hi RESOLUTION Switch between 470 530 TVL only with FCB 1010P Some products may not be available in your country please contact our distributor for more details 6 050 Preset Scan FUNCTION SETTING PRESETS gt SCAN PATT
12. d once the camera is pointed on it such as lavatory areas the operation desk of an ATM machine This might be mandatory required by local law regulations The Speed Dome supports up to 24 private masks depending on the installed camera module please contact your local sales representative for more information Hitachi camera modules 8 masking areas Sony Camera modules upto 24 masking areas except the 45 series provides only 8 LG CNB Camera modules no masking function WINDOW NUMBER Mask number EDIT WINDOW Edit position of the mask using the keyboard s joystick Presse IRIS OPEN to save ENABLE WINDOW Shows the mask on the screen 18 CLEAR WINDOW Deletes the mask Some products may not be available in your country please contact our distributor for more details 6 0SD Alarm Setting ALARMS RESUME OFF RESETDELAY 020 ALARM CONTACT ALARM SETTING BACK EXIT ALARM SETTING ALARM NUMBER 001 ALARMACTION TOUR ACTIVATEAUX AUX1 BACK EXIT Alarms RESUME Continues the previous function of the camera before the alarm was activated RESET DELAY How long the camera stays in Alarm mode ALARM CONTACT Setting between N C normal Close or N O normal Open ALARM NUMBER Ranging from 1 7 ALARM ACTION Setting for PRESET SCAN TOUR PAT 1 4 or NONE if the camera s alarm function is activated ACTIVATE AUX Setting Alarm Output when alarm is activated Se
13. ducts may not be available in your country please contact our distributor for more details SETTING BLANKING o 2 2 4 4 8 Z SYSTEM SETTING CAMERA SETTING FUNCTION SETTING ALARMS EXIT FUNCTION SETTING CAMERA SETTING EDIT DOME LABEL Some products may not be available in your country please contact our distributor for more details 6 OSD System Setting SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP BACK EXIT EDIT DOME LABEL INITIAL INFO FIRMWARE V2 33 PROTOCOL FACTORY DOME ADDRESS 001 COMM 4800 N 8 1 BACK EXIT DISPLAY SETUP DOME LABEL OFF TX PRESET LABEL OFF ZOOM LABEL ON ZONE LABEL OFF DIRECTION LABEL ON TEMPRATURELABEL BACK EXIT System Setting In the system setting menu you can modify operation and display settings such as dome label temperature and display of various values on the operational screen Dome Label 1 use UP or DOWN to change the character 2 use RIGHT to move to next character 3 use RIGHT to move to last char and to save 4 use Left to go to first char and to cancel Initial Info Shows the information about current settings Display Setup Enables the display for the on screen info during operaton mode Dome label Name of the dome Preset label Shows the label of every preset Zoom label Shows
14. e Communication 0 4 300 per sec 360 0 4 150 per sec 0 90 RS485 Multiple Protocol Coax Preset Positions Auto Pan Tour Sequence 128 Presets Yes between 2 presets 4 Programmable Tours with Max 24 Presets 4 Patterns up to 180s Alarm Input Up to 4 Alarm Inputs Heater amp Blower Built in Power 24V AC 24 60VA Outdoor Operating Temperature Outdoor 40 C 60 C Dimension 6 56 x 10 5 H 200cm 9 x 320cm H 29 Specifications and appearance are subject to change without notice P 017 26 Some products may not be available in your country please contact our distributor for more details Some products may not be available in your country please contact our distributor for more details R201402 V20
15. eletric shock Do not point the camera lens directly to sunlight or any strong light source This will cause permanent damage to the camera and avoids the warranty Read this user s manual carefully before operating the appliance Make sure that local electric safty standard are followed when using or installing the appliance Do not install the camera in other orientation as designed And do not bend or squeez the sturctiure as this may damage the mechanic sturcture of the appliance and avoids the warranty Do not touch the Cover with bare hands or any object These will scratch the serface and affect the image qulaity Some products may not be available in your country please contact our distributor for more details The high speed dome camera series are designed for in and outdoor video surveillance application The integrated motorized pan tilt mechanic allows user to point the camera to any position 360 horizontal and 180 vertical Both series can be equipped with digital zoom camera modules which provide zooming functon from 18 to 36 times optical and advanced image features Key features 360 Pan and 180 Tilt range 90 with auto image flip Support most well known camera modules 128 preset points memory 80 can be used for auto tour function 4 pattern tours 4Scan tour Basic setup directly from Keyboard Advanced setup through OSD On Screen Display menu up to 24 privacy masking zones des
16. ion CAM TITLE 32 0 Temperature Current temperature inside the speed dome C Cam title User definable camera title ZONE 1 Zone Current zone name 285 78 18X Pan deg Pan angle 0 359 Tilt deg Tilt angle 0 90 Zoom Factor Zoom factor Zoom factor Display of the information can be activated or deactivated through the OSD menu Pplease refer to the system setting for detais Tilt degree Pan degree Zone description PTZ operation For the surveillance operation the dome can be controlled from a keyboard device Multiplexer or DVR through RS485 interface Make sure that the cable is connected and the settings baud rate Address ID and protocol of both keyboard and the dome are correctly configurated For further details on operating the PTZ please refer to the user s manual of the keyboard Some products may not be available in your country please contact our distributor for more details OSD Menu The speed dome are equipped with the new OSD Menu function All operational functions and camera related settings can be controlled here In order to use the OSD function a telemetric controller device such as keyboard DVR or other devices with similiar functions is required Please make sure that the device used is properly physically connected to the dome and all connection parameters are set How to start the OSD Menu To start the OSD Menu you need to press the following sequence on the keyboard
17. jojo joo ojojojojojojo o o o jo jojoio I 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 i e ejo jo jc 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Some products may not be available in your country please contact our distributor for more details Some products may not be available in your country please contact our distributor for more details 24 2345678 Switchnumber Swl Bit 1 a hh kami hh I hami har rl m rj I kami hh kami hami bami kami kami 86 Gami bami kami kami bami HH bami HH sj HH sj Hj HE hami hami kami kami HJ H HE ay H H hami hami bami kami H Hx HJ yy h he HE H bami hami kami HJ hami bami H immi kami bami bami kami bami kami kami bam ham kammi hami kami kami Dami kamm hj hs 00 00 yy Some products may not be available in your country please contact our distributor for more details Swl fi 0 0 0 0 2 S e 5 o E 5 o J o o a 2 a 5 o 5 gt E E ky gt o ia c gt 2 o 3 o g a o o 2 itio
18. lect between AUX1 AUX2 not connected or BOTH Alarm Connection on Backboard GND _ input 1to 7 Common port gt Alarm output 1 Alarm output 2 1 products may not be available in your country please contact our distributor for more details 7 PROTOCOL SETTING Protocol Setting SW 1 Represents the dome s address in binary form This procedure is needed if a connection of the telemetric control with the keyboard device is desired You need to setup the dome address and protocol settings The speed dome supports multiple communication protocols The settings can be changed by rearranging the DIP Switches on the rear side of the connector board as illustrated Please use the following table for detailed information Please refer to the list on the next pages for reference SW 2 Used for protocol settting and baud rate DIP 1 to 6 Protocol settings DIP 7 and 8 Baud rate settings 2400 bps 0 0 4800 bps 1 o 9600 bps 0 1 19200 bps 1 1 B02 001100 DIAMOND 100100 HUNDA 101100 KALATEL 010100 LILIN 110100 MOLYNX 001000 PANASONIC 111000 PELCO D P 100000 PHILIPS 000001 SAE 010000 SAMSUNG 000100 SANTACH 011000 UNIVISION 010001 VCL 110000 VICON 101000 AD 001100 Some products may not be available in your country please contact our distributor for more details oo o o ojojlo jojojo
19. o use underground cables shielded by steel tube Do not install the cable without any protection In athunderstorm area or region with high inductive voltage such as high voltage transformer stations itis necessary to use additional lightning proof equipment and or lightning rods for protection For outdoor installations lightning protection and grounding of the device should be considered Please refer to the industrial saftey regulations of your country Grounding of the appliance should include anti interference and fulfill the safety requirements Do not connect the ground with short circuited or other high voltage electric networks The resistance of down conductor should not exceed 4 Ohm and its thickness should be atleast 25mm This appliance has the lightning proof function which can prevent damages caused by high voltage pulse such as lightning strikes below 1500 V This appliance meets the Ip66 standard for water and dust proof Do not install the in door model for out door applications as the model is not designed withstanding permanent water exposure Make sure that the installation is protected from long time water drop or spatter which may damage the appliance Make sure that the enviroment of installation meets the requirements of the appliance such as holding the weight and providing enough space for bracket and power supply Some products may not be available in your country please contact our distri
20. onnected to power the power LED will light up Optional bracket accessories The speed dome can be equipped with various bracket accessories for indoor and outdoor installation Please contact your distributor for further details T al Ceilling Wall mount and Corner Indoor wall Outdoor mount Power box mount mount Power box gu J f Indoor Indoor ceilling Extended wall Swan neck Wall embedded mount mount mounting mount mount bracket d products may not be available in your country please contact our distributor for more details 5 OPERATING THE SPEED DOME 737 Initial Screen After powering up the camera will enter into the self test mode and display the status screen see picture left It contains information about the model and current settings FIRMWARE Model number V2 25 Current firmware version Protocol Current control protocol Dome address Address ID of speed dome Please refer to the section Protocol setup for details Comm 9600 N 8 1 Current setting of the serial communication interface 9600 Baud rate Please refer to section Baud Rate setup for details N 8 1 No parity bit 8 bit length 1 stop bit This setting cannot be changed The intial screen will remain on until any user action is taken If the power up action is set the initial info wil vanish immediately Operation Screen Temperature The operation screen can display additional Y informat
21. pends on camera module 7 alarm input amp 2 output 4 input amp 1 output pre wired Multi Protocol through RS485 or coaxial cable Direction Indicator on screen Aluminum Alloy structure with high intensity and heat sinking High precision step motor for flicker less image during movement Camera Features HighResolution with 520TVL and Wide Dynamic Auto Focus Auto lris Auto Brightness control Auto Balance IR cutter control Day Night mode switching Available in 36X only Auto Slow Shutter Temperature monitoring and protection Alarm notification will be displayed once the inner temperature exceeds the limit Inlow temperature area the dome camera will only start after the operation temperature is reached Cooling fan activity is managed by the CPU extends the duration Other features Proportional pan for Focus Speed on different zoom factor Auto resuming user defined action such as tour pattern or scan after selectable idle time Power up Action activates tour or pattern by default depends on camera module type Some products may not be available in your country please contact our distributor for more details 3 PACKING LIST Indoor Core unit Indoor Roof Mount Instruction and 1 piece base plate operation manual 1 piece 1 piece Outdoor U Os Core unit Outdoor housing 1 piece with sun shield and cover 1 piece WARNING The transparent cover part is
22. rameters can be set SCAN NUMBER Supports up to 4 scans SCAN SPEED Cruising speed between the points SET LEFT LIMIT Defines the left point SET RIGHT LIMIT Defines the right point CLEAR SCAN Deletes the scan setting RUN SCAN Starts the scan function EDIT SCAN LABEL Sets the name for the scan 16 Some products may not be available in your country please contact our distributor for more details PATTERNS PATTERN NUMBER 1 PROGRAM PATTERN RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL BACK EXIT TOURS TOUR NUMBER 1 EDIT TOUR RUN TOUR CLEAR TOUR EDIT TOUR PO S TM PO S TM PO S TM 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 Patterns Patterns record the user s movement while performing PTZ operations and stores themas a track The Speed Dome can record up to 4 tracks with max 180 sec each PATTERN NUMBER Supports up to 4 patterns PROGRAM PATTERN Starts recording the pattern when selected You can perfom PTZ movements for recording not exceeding 180 sec Press IRIS OPEN to save the track RUN PATTERN Starts the current pattern CLEAR PATTERN Deletes the current pattern EDIT PATTERN LABEL Sets the name for the current pattern Tour Tour is an auto operation running through selected prese
23. s Do not attemp to disassemble the appliance To prevent electric shock do not remove screws or cover There are no user serviceable parts inside Contact qualified service personnel for maintenance Handle the appliance with Care Do not strike or shake as this may damage the appliance It should be protected against extreme pressure vibration and humidity during transportation and storage Damages caused by improper transportation avoid the warranty Do not use strong or abrasive detergents when cleaning the appliance body and transparent cover Use a dry cloth to clean the appliance when it is dirty When the dirt is hard to remove use a mild detergent and wipe gently Do not operate the apliance beyond its speci ed temperature humidity or power source ratings Do not use the dome camera in an extreme environment where high temperature or high humidity exists Use the indoor models within 10 C to 50 C 14 F to 122 F and a humidity below 9095 The input power source is 24V AC 50 60Hz and requires 1000mA Use the outdoor models within 20 C to 60 C 4 F to 140 F and a humidity below 9095 The input power source is 24V AC 50 60Hz and requires 2500mA Do not expose the indoor model of dome camera to water or moisture not try to operate it in wet areas Take immediate action when the indoor speed dome becomes wet Turn off the power and refer servicing to qulified service personnel Moisture may damage the appliance and cause
24. sensitive and must be handled with care Do not touch or rub the surface in any way with the protection foil Inproper cleaning methods will cause permanent scratches on the cover and cause unclear image or focusing error of the camera For cleaning the cover replace the original cover with the spare cover then wash it by immersing it into warm water containing a non corrosive cleaning agent mE Sparedome Instruction and cover operation manual 1 piece 1 piece V C 4 Some products may not be available in your country please contact our distributor for more details 4 INSTALLATION Safety Instructions before starting Do not install and operate this appliance in a flammable and or explosive environment Make sure that the installation is done according to the local electricity safety regulations of your country Before installation and maintenance make sure that the appliance is disconnected from the power source Do not use any power source other than 24V AC in order to prevent damages to the device Please refer to the section Precaution for more details Handle the device during the installation with care Droping the product or extreme vibration may cause irreparable damages and void the warranty Do not install or operate the appliance close to high voltage devices or high voltage cables The safety distance should remain at least 50 m To achieve best image quality it is recommanded t
25. t points with definable pause time Atour can store up to 24 preset points TOUR NUMBER Supports up to 4 tours TOUR PRESETS P0 Move the joystick up and down to select the preset points by number and save the settings by going to the left end of the line If a selected point has the value 0 all the following preset points will be ignored SPEED S Speed of the dome between 2 points TOUR DWELL TM Pause duration after reaching a preset point Duration can be set between 00 60 s RUN TOUR Starts the tour and exits the OSD Menu Some products may not be available in your country please contact our distributor for more details ZONES ZONE NUMBER 1 SETLEFTLIMIT SET RIGHT LIMIT CLEAR ZONE EDIT ZONE LABEL BACK EXIT WINDOW BLANKING WINDOW NUMBER 01 EDIT WINDOW ENABLE WINDOW OFF CLEAR WINDOW BACK EXIT Zones You can define the zones in the whole PT range up to 8 zones When the display setting Zone Label is activated its label will be displayed on the screen The defined ranges ofthe zones should not be overlapping ZONE NUMBER Supports up to 8 zones SET LEFT LIMIT Left boarder of the current zone SET RIGHT LIMIT Right boarder of the current zone CLEAR ZONE Delet the current zone EDIT ZONE LABEL Changes the label name of the current zone Privacy Mask Window Blanking Privacy Mask is used to protect the privacy area that should not be displaye
26. zoom factor on screen Zone label Shows the zone name Direction label Shows the coordinates Temperature label Shows the current temp in the dome MOTION XYAUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 040 BACK EXIT Ma CLEAR CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART BACK EXIT PASSWORD SETUP OLD PASSWORD NEW PASSWORD CONF PASSWORD ENABLE PASSWORD OFF BACK EXIT 6 0SD Motion Clear Password Motion control AUTO FLIP Auto image flip tilt range from 90 to 180 PROPORTIONAL PAN Depending on the zoom factor the dome will adjust the pan and tilt speed automatically for comfortable viewing PARK TIME Defines the idle time prior to start a custom defined action park action The duration can vary from 1 to 240 minutes This function can bedisabled by setting the minute to 0 PARK ACTION The action which will be started after the idle time park time Selectable between Preset Scan Pattern Nr Tour or None POWER UP ACTION Action which starts after power up and self test Selectable between Auto Preset 1 Scan Pattern Nr Tour or None By selecting Auto the dome will resume the last action before power off FAN ENABLED Defines the temperature limit in C at which the internal cooling starts operating The
Download Pdf Manuals
Related Search