USER MANUAL - AV-iQ
Contents
1. Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHO IS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty T Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removal or installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WI2. 9 12V DC 00000 o o ae H Ca XGA HD INPUT LINE OUT 1 LINE OUT 2 T Figure 2 TP 112HD Top Side Panel ON O O Figure 3 TP 112HD Lower Side Panel Your TP 112HD XGA HD Line Transmitter DA Table 1 TP 112HD XGA HD Line Transmitter DA Features Feature Function 1 12VDC 12V DC connector for powering the unit 2 LINE OUT 2 RJ 45 Connector Connects to the LINE IN RJ 45 connector on the second TP 120 XGA Line Receiver 3 LINE OUT 1 RJ 45 Connector Connects to the LINE IN RJ 45 connector on the first TP 120 XGA Line Receiver 4 XGA HD INPUTHD15F Connector Connect to the XGA source 5 ONLED Illuminates when receiving power Figure 4 and Table 2 define the TP 112HD underside panel CY NEGATIVE NoRMAL Hs Figure 4 TP 112HD Underside Panel Table 2 TP 112HD Underside Panel Features Feature Function 1 VS Switch Slide the switch to the left to change the VS polarity to NEGATIVE polarity slide the switch to the right to NORMAL to retain the polarity 2 HS Switch Slide the switch to the left to change the HS polarity to NEGATIVE polarity slide the switch to the right to NORMAL to retain the polarity 1 Using a UTP CATS cable with RJ 45 connectors at both ends the PINOUT is defined in Table 3 and Figure 6 2 R
3. pin to pin cable with RJ 45 connectors Table 3 CAT5 PINOUT EIA TIA 568A EIA TIA 568B PIN Wire Color PIN Wire Color 1 Green White 1 Orange White 2 Green 2 Orange 3 Orange White 3 Green White 4 Blue 4 Blue 5 Blue White 5 Blue White 6 Orange 6 Green 7 Brown White 7 Brown White 8 Brown 8 Brown meas CRAT Pair 1 4and5 Pair 1 4and5 Pair2 3and6 Pair 2 1and2 Pair3 1and2 Pair3 3and6 Pair4 7and8 Pair 4 7 and 8 Figure 6 CATS PINOUT 12 45 78 36 Technical Specifications 6 Technical Specifications Table 4 includes the technical specifications of the TP 112HD Table 4 Technical Specifications of the TP 112HD with 100m CATS cable INPUT 1 XGA HD on an HD15F connector OUTPUTS 2 RJ 45 OUT connectors MAX OUTPUT LEVEL 1 7Vpp HIGHEST RESOLUTION UXGA 1080P DIFF GAIN 4 DIFF PHASE 0 3 Deg K FACTOR 0 1 S N RATIO 65dB CONTROLS 2 switches for sync inversion COUPLING AC POWER SOURCE 12 VDC 522mA DIMENSIONS 12cm x 7 15cm x 2 76cm 4 7 x 2 8 x 1 08 W D H WEIGHT 0 3 kg 0 67 Ibs approx ACCESSORIES Power supply 1 Specifications are subject to change without notice 2 For the TP 112HD Transmitter TP 120 Receiver SETUP 3 Sufficient for feeding two receivers via CAT5 8 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY
4. site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution 9001 o SC QS gd oc Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000135 REV 1
5. Kramer Electronics Ltd l KRAMER USER MANUAL Model TP 112HD XGA HD Line Transmitter DA Contents Contents 1 Introduction 2 Getting Started 3 Overview 3 1 About the Power Connect Feature 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP 3 3 About the TP 112HD 3 4 Recommendations for Achieving the Best Performance 4 Your TP 112HD XGA HD Line Transmitter DA 5 Configuring a 1 2 XGA HD to Twisted Pair DA System 5 1 Wiring the CAT5 LINE IN LINE OUT RJ 45 Connectors 6 Technical Specifications Figures Figure 1 TP 112HD XGA HD Line Transmitter DA Figure 2 TP 112HD Top Side Panel Figure 3 TP 112HD Lower Side Panel Figure 4 TP 112HD Underside Panel Figure 5 Configuring a 1 2 XGA HD to Twisted Pair Transmitter Receiver DA Figure 6 CAT5 PINOUT Tables Table 1 TP 112HD XGA HD Line Transmitter DA Features Table 2 TP 112HD Underside Panel Features Table 3 CAT5 PINOUT Table 4 Technical Specifications of the TP 112HD with 100m CATS cable Ge AU Q QO SD D H ka AD BW W WD o0 Ab AR Introduction 1 Introduction Welcome to Kramer Electronics since 1981 a world of unique creative and affordable solutions to the infinite range of problems that confront the video audio and presentation professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 350 plus differe
6. LL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for L Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incide
7. ables is on our Web site at http www kramerelectronics com 1 Overview 3 1 About the Power Connect Feature The Power Connect feature lets you power a transmitter receiver system by connecting just one power adapter to either the transmitter or the receiver The other unit is fed over the same cable The Power Connect feature applies as long as the cable is heavy gauge cable that is it can carry power The distance does not exceed 50 meters on standard CATS cable For a distance of 100 meters separate power supplies must be connected to the transmitter and to the receiver simultaneously unless using heavy gauge cable 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP The decision whether to use shielded twisted pair STP cable or unshielded twisted pair UTP cable depends on the nature of the application It is recommended that in applications with high interference shielded twisted pair STP cable is used However the shield itself does create a capacitance that degrades the frequency response of the machines For shorter distances of 50m or so shielded twisted pair STP cable is preferred because it provides protection from interference degradation is non apparent For a long range application unshielded twisted pair UTP cable is preferred However the unshielded twisted pair UTP cable should be installed far away from electric cables motors and so on which are prone to create electrical i
8. apter to the mains electricity The signal from the XGA source is transmitted via the two CATS cables decoded and converted at the each of the XGA OUT HD15F connectors to the XGA acceptors 4 Onthe TP 120 units if necessary Set the H SYNC and V SYNC switches on the underside e Adjust the video output signal level and or cable compensation equalization level 5 Onthe TP 112HD if necessary set the VS and HS switches on the underside 1 Refer to the separate user manual PT 110 PT 120 TP 120 WP 110 which can be downloaded from the Internet at this URL http www kramerelectronics com 2 Via UTP cabling with a range of more than 300ft gt 100m For details of how to wire a CATS LINE IN LINE OUT RJ 45 connector see section 5 1 3 By default both switches are set down for negative V SYNC and H SYNC polarity 4 Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level 5 By default both switches are set to the right to NORMAL to retain the V SYNC and H SYNC polarity 5 Configuring a 1 2 XGA HD to Twisted Pair DA System Long CAT 5 cable Computer Graphics Source Display 2 Figure 5 Configuring a 1 2 XGA HD to Twisted Pair Transmitter Receiver DA KRAMER SIMPLE CREATIVE TECHNOLOGY Configuring a 1 2 XGA HD to Twisted Pair DA System 5 1 Wiring the CAT5 LINE IN LINE OUT RJ 45 Connectors Table 3 and Figure 6 define the UTP CAT5 PINOUT using a straight
9. efer to the separate user manual PT 110 PT 120 TP 120 WP 110 which can be downloaded from the Internet at this URL http www kramerelectronics com Also see the example illustrated in Figure 5 3 By default both switches are set to the right 4 Downgoing syncs 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Configuring a 1 2 XGA HD to Twisted Pair DA System 5 Configuring a 1 2 XGA HD to Twisted Pair DA System You can use the TP 112HD XGA HD Line Transmitter DA with two TP 120 XGA Line Receiver units to configure a 1 2 XGA HD to Twisted Pair DA system This will let you transmit a computer graphics HD signal to two displays via long line CATS UTP cabling To connect the TP 112HD to two TP 120 units as the example in Figure 5 illustrates do the following 1 On the TP 112HD connect the XGA HD source for example a computer graphics HD source to the XGA HD INPUT HDI5F connector and connect the line output RJ 45 connector e OUT 1 connector to the LINE IN RJ 45 connector on the first TP 120 e OUT 2 connector to the LINE IN RJ 45 connector on the second TP 120 2 Onthe two TP 120 units connect the e XGA OUT HDISF connector of the first TP 120 unit to the XGA HD acceptor for example Display 1 e XGA OUT HDISF connector of the second TP 120 unit to the XGA HD acceptor for example Display 2 3 On each of the three Kramer TOOLS connect the 12V DC power adapter to the power socket and connect the ad
10. nt models now appear in 8 Groups which are clearly defined by function Congratulations on purchasing your Kramer TOOLS TP 112HD XGA HD Line Transmitter DA which is ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals security and stores The package includes the following e TP 112HD XGA HD Line Transmitter DA e Power adapter 12V DC Input This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 3 Overview This section describes e The power connect feature see section 3 1 e Using shielded twisted pair STP unshielded twisted pair UTP see section 3 2 e Asummary of the TP 112HD see section 3 3 e Recommendations for achieving the best performance see section 3 4 1 GROUP 1 Distribution Amplifiers GROUP 2 Video and Audio Switchers Matrix Switchers and Controllers GROUP 3 Video Audio VGA XGA Processors GROUP 4 Interfaces and Sync Processors GROUP 5 Twisted Pair Interfaces GROUP 6 Accessories and Rack Adapters GROUP 7 Scan Converters and Scalers and GROUP 8 Cables and Connectors 2 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 3 The complete list of Kramer c
11. ntal consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION DO Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment DO Use the supplied DC power supply to feed power to the machine B Please use recommended interconnection cables to connect the machine to other components 9 For the latest information on our products and a list of Kramer distributors visit our Web
12. nterference 3 3 About the TP 112HD Your Kramer TOOLS TP 112HD XGA HD Line Transmitter DA e Receives a computer graphics HD signal and transmits it over two CATS cables to appropriate receivers e Has a video bandwidth of 150MHz with a transmission range of more than 300 ft more than 100 meters e Includes the Power Connect feature e Is 12VDC fed 1 The terminology XGA is used throughout this manual where this implies any RGBHV signal on an HD15 connector having a resolution from VGA up to UXGA 2 The TP 112HD accepts high definition resolutions 480p 576p 720p 1080i and 1080p 3 Note that the CATS connectors exclude audio 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Your TP 112HD XGA HD Line Transmitter DA 3 4 Recommendations for Achieving the Best Performance Achieving the best performance means Connecting only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoiding interference from neighboring electrical appliances that may adversely influence signal quality and positioning your TP 112HD away from moisture excessive sunlight and dust Your TP 112HD XGA HD Line Transmitter DA Figure 1 Figure 2 Figure 3 and Table 1 define the TP 112HD p e n XGA HD Line Transmitter DA TP 112HD Figure 1 TP 112HD XGA HD Line Transmitter DA
Download Pdf Manuals
Related Search