User`s Manual
Contents
1. For PIC16F57 connection shall be subject to 17PIN PGD 16PIN PGC 2PIN VCC 4PIN GND 28PIN VPP MCLR In case of in circuit download relative external circuits connecting to ICSP output cable on user board shall be shut down Otherwise the effects of other external circuits may cause failure of programming Furthermore if current consumption of 5V voltage on user board is more than 200MA the user board must be self supplied with power of 5V voltage In addition VPP pin in download circuit shall be connected with 10K resistor pulling up to VCC In technical manual of MICROCHIP there are typical circuits about in circuit programming for references 14 Entire Process of Chip Programming Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Connect programmer hardware with PC connect power supply of programmer Run programmer software If message indicates failure select programmer type manually Select hardware connecting port to enable communication between software and hardware or run Option Auto Find Borad for automatic setup of programmer type and connection port Select chip type and chip According to the installation graphics as software indicates install the chip onto programmer socket if use QL PIC280 then pin 1 of chip is aligned with pin 1 at handle of socket Load the file to program Confirm and properly s2. Load the dialog of selection of file will appear 2 Select the type of file to open in the list under File Type T For example to open file of hexadecimal system please select Hex File Hex 3 Select the file to open under the directory 4 Click Open button in dialog the file will be transferred into current buffer 4 Edit Buffer You may edit current buffer by running Option Edit Buffer or pressing Edit button on software panel After running the command software pop up window to edit buffer will appear as shown in below diagram IFEF 3FFF srrr FFF rrr SFFF 3FFF SFFF Change the content of buffer first put mouse cursor on the address to edit double left click to select address content delete original content with Delete key on keyboard and then input the new content After edit click bottom OK button on edit window to exit The software will automatically save the change in current buffer If you don t desire to change the content you may single click Cancel to exit the edit window 5 Set Configuration Bit You may set or change the configuration bit of chip by running Option View Edit Fuses And ID or pressing Fuses button on software panel After running the command software pop up window to set configuration bit will appear as shown in below diagram Set the options according to your requirement and click OK button 10
3. I x wit ti iS PwRTe OFF t tst s d BODEN ON x uve ON x Code Frotect EEP Dzabed FLASHMWeteProect jon sf Deba 0FF zj Osaa a Code Protect Disabled x 9 FFFFFFFF OK Cancel Heb User s ID can also be input in set window of configuration bit If configuration bit information has been written in your program direct programming will be available without reset of configuration bit Note Setup of configuration is very important which directly affects the availability of your program Consequently before programming we must confirm the setup of configuration bit is entirely correct Different chips require different configuration bit options The detailed setup 11 information can be obtained by checking the DATASHEET of chip DATASHEET of chip can be downloaded from official website of MICROCHIP at www microchip com The following are listed for your reference Setup of external crystal oscillator select LP for below 200K select XT for 200K 4m select HS for 2M 20M For 4M crystal oscillator at critical state of XT and HS if chip doesn t work when you select XT please try HS For the beginner who doesn t know how to set configuration bit to shut down or disable the functions which are not required if possible e g Watchdog Power up Delay Power down Monitor DEBUG Mode Low Voltage Programming all these functions can be shut down or disabled If the chip is programme
4. nget WFF IV Use of Software 1 Select Communication Port Select Programmer Hardware Connect hardware and power up run the software which will automatically search programmer hardware If search fails and indicates Hardware isn t connected Please reset hardware you can set programmer hardware manually We offer two methods for user to select communication port and programmer type Method 1 Directly run Auto Find Borad under Option Software will scan the port connecting hardware 6 automatically and check the type of programmer After scanning software will switch to correct connecting port and programmer type and indicate to find the programmer If software fails to find programmer please check if the connection to programmer hardware and power supply Method 2 Directly select the port from the list of Port Selector at top right of the software Directly select proper programmer from Select Programmer under Option Note Only existing ports of computer are shown in the list If only COM1 is installed at your computer there is only COMI for your choice If you have connected USB but can t find it in the list the reason may be that the software is started too fast You can shut down the software and restart it 2 Select Chip Type and Chip A Select Chip Type Chip Family The control for selection of chip type is at top right of the software as shown i
5. access installation interface of application software and operate according to prompts to finish the installation Its shortcut will appear on desktop automatically after installation 2 Installation of USB Driver When you first use the USB of this programmer for communication please connect PC and programmer hardware through USB cable Then PC system will indicate to find new hardware and request installation of driver for this hardware You can operate in regular way and designate path to install driver which is under directory usbdriver of attached CD After installation a serial port will be added to your computer Now the programmer is connected to the serial port converted from USB When there is no system message to find new hardware after programmer hardware is connected please check Any bad or broken connection for USB cable Does USB of computer works smoothly Maybe there is similar USB driver already installed in your computer You may connect programmer hardware right click My Computer select Property in pop up list switch to Hardware from System Property window and then click Device Manager to check Port COM and LPT If you can find USB Serial Port COMX the driver of this programmer has been installed in your computer this operation requests proper connection of hardware and PC II Running of Software After proper installation shortcut of th
6. Inc Step length increment of chip SN after each programming Formt Hex set SN auto increment step at hexadecimal system Dec set SN auto increment step at decimal system a7 Setting Increasement From Hei Adr chip SN is auto incremental from high address to low address Ignore Hei Byte of Word ignore high byte of each word reserve low byte only Each time Program Successful after Save current file go buffer after successful programming of chip there is one auto increment of SN The value of current buffer will be saved to current file Test Test auto increment scheme of chip SN Properly set all options and click OK to apply current setup in the program or click Cancel to exit 13 About ICSP Programming Please enable ICSP Mode under Option manual On side of programmer there is one 6 PIN telephone socket that is interface of in circuit programming We may directly use the download cable attached with the programmer for in circuit on board programming Sequence of ICSP download cable is exactly same with MCD2 ICD2 as shown below I MCLR VPP gd rhite 2 VDD 3 GND 4 PGD generally RB 5 PGC generally RB6 6 LVP ENABLE seldom use 6 blue blue When using it we only need to connect the output cable of ICSP with corresponding pin of chip you desire to download For 12XXX series chip connection shall be subject to PGC GP1 and PGD GPO
7. QL PROG Microchip MCU Programmer User s Manual 7A L QianLongSheng Qianlongsheng Electronic Technology Co Ltd INtPOMUCHON seinnaa onesie aaa Aa a A R 1 Feat r s eiai ire ar aa a a a aa a i a A O E i 1 Operation Instruction 0 0 0 eee ceseeeseceecenecececeneceeeceaecececeaecececeeecenecsneeaeenes 3 I Hardware Instalatii unica cece onaniaa a 3 M Software Installations enei e E a a 4 1 Installation of Programming Software eee eee eeeeees 4 2 Installation of USB Driver eee cece ese ceeeeeeeseeaeeneeeeeeaees 4 II Running of Softwares aisle Aral sleet shes tiei tes 5 IV Use of SoftWare oe eaa aaa tsi iidais cinta sein iete 6 1 Select Communication Port Select Programmer Hardware 6 2 Select Chip Type and Chip simsii mirassmeseiioesi misos 7 3 Load Fil to Program teise oe othe eetons a as 8 4 gt Cit Bunter mirtini val ee abet e s caidas E 9 5 Set Configuration Bit le aE E E 10 6 Setup and Protect of Parameter Calibration of Internal Clock 12 To Saye Ple es shoes oy S26 Res E rodeo ud eaets side ccaeagen E E ai 13 8 Preset Programming Quantity oe eeeeeeseeseeteeeeeeaes 14 9 Installation Position Of Chip eee eee eee eeeeeeeeeeseeeeeeeeeas 14 10 Fully Automatic Production Programming 15 11 About CHECKSUM aron a teen states e a AE a 16 12 About Serial Number Auto increment Programming 16 13 About IC
8. SP Programming eseseeeeseeessssessresrsresesrseessreseses 18 14 Entire Process of Chip Programming uu eee eects 20 15 Hardware Online Upgrade eee eeeeseeeeseeeeeeeeees 21 Technical SUpport seene nnn ae aa e tea atone in ea eee 21 Introduction QL 2006 QL PIC280 programmer is the high speed programmer designed specially for development and production programming of PIC single chip microcomputer SCM by Shenzhen Qianlongsheng Electronic Technology Co Ltd The product is featured with small volume low power consumption high reliability as well as easy and convenient operation QL 2006 is applicable for almost all PIC10 12 16 18 series SCMs except 16C5X It also supports memories in 24XX series and 93XX series QL PIC280 fully supports entire PIC series of more than one hundred types including 10 12 16 18 It also supports serial EEPROMs including 24 93 series from 1K to 512K bit With fully open design of electronic switch using high current field effect transistor FET and collocation of all chips aligned to the top this programmer has more stable programming performance more prompt application and more convenient operation Features Features of QL 2006 QL PIC280 Programmer High performance price ratio designed with the updated PIC programming algorithm higher speed than other similar products stable performance support more devices Support online upgrade of programmer hardware eas
9. d for production please carry out the setup correctly according to the requirements of your hardware and software 6 Setup and Protect of Parameter Calibration of Internal Clock For most of the chips with internal clocks there is calibration value of internal clock stored in the last address of ROM when leaving the factory This value can be used to calibrate the accuracy of internal clock frequency in the program when internal oscillation is applied for the chip 12 There are two options in our software under Option CAL Program Option that is Preserve OSCCAL Calibration Value and Use File If we select Preserve OSCCAL Calibration Value our software will always protect this value in chip unchanged regardless of value in the last address of current buffer and regardless whether you run CALIB on software panel to change this value or not In this case CALIB button is invalid now If we select Use File the value in current buffer will be used to change the original calibration value of clock when programming Now we may press CALIB button on software panel to input the calibration value of clock we desire For new chip or the chip whose clock calibration value is never changed we recommend Preserve OSCCAL Calibration Value to protect this value of chip unchanged For the chip whose clock calibration value has been changed we may select Use File and input the value we desire by press
10. ents The right of change in this manual is reserved without any prior notice Any inconsistency of this manual caused by upgraded of software version will be subject to software Warranty Service Qianlongsheng Electronic Technology operates under strict product quality assurance system Within one year after the date of purchase maintenance is available free of charge for both software and hardware problems The warranty is subject to correct installation of software and operation under designated working condition In addition if you have any other questions or suggestions to our application software please contact us and we will always be dedicated in serving you 2932
11. et the configuration bit of chip If chip has internal clock whose calibration value is used in the program please calibrate the clock or properly set Cal Program Options under Optin Preset programming quantity as required properly set SN auto increment parameter this step may be omitted Properly set programming options Press Program button to program Take out the chip programmed and insert the chip to program Repeat Step 11 and Step 12 until all chips are programmed Exit disconnect hardware and PC or cut off hardware power 20 Step 15 Finished 15 Hardware Online Upgrade Run Download Operating System under Option current programmer hardware will be upgraded to the version attached in the software to enable the new added function new added device or improved function Each software version is related to one hardware version If you desire to upgrade hardware to the higher version please download the updated software from our website Then install the software and start it run Option Download Operating System to upgrade your hardware version More often when software is upgraded to a higher version the hardware isn t changed Now you can use the updated software stably without upgrading your hardware The note under installation folder of software will indicate if hardware upgrade is required or not when the new software is applied You may refer to help Protocol for current
12. hardware version Technical Support Customer Support When our R amp D department is working hard for high quality product our sales department is also making every effort to provide perfect pre sales and after sales services From our website you may find the prices of our products and purchase method You may also view the product appearance online Of course should you have any difficulty for help you may turn 21 directly to local sales agent distributor or our engineers for technical support Our customer support staff will track the problems and help to solve them completely For better service please make the following preparations before you contact us If you can t understand the program please study the user manual first carefully Ifthere is fault during running of software please repeat it Incase of fault message please record it Please sit in front of computer when you call us for convenient contrast and prompt solution of the problem We are not liable for the following cases Product repaired or changed by organization or individual who are not authorized by us formally Damaged product due to fault operation and product changed by user Program fault due to physical damage of CD Any joint liability extension due to hardware fault or software defect Licensing Agreement Qianlongsheng Electronic Technology reserves all rights that are not expressly granted 2550 Statem
13. ing CALIB button on software panel this value may be read from other chips with the same lot number Then we can start the programming When all chips have their own clock calibration values we had better reset SCAL Program Option to Preserve OSCCAL Calibration Value 7 Save File You may run File Save Jor press Save button on software panel to save the current file as hexadecimal system file At the same time configuration information of chip is saved For the next time this file is loaded configuration information of chip will be automatically set as the configuration word saved 1 Click icon on tool bar or select File Save dialog to save the file will pop up 2 Select the file to save in list of Save Type T For example to save file of hexadecimal system please select Hex File Hex 3 Input file name to save in File Name box 4 Click Save button in dialog 8 Preset Programming Quantity You may set the chip quantity to program in one order or within one day by pressing Pset button on software panel After setup it will count the programming chips When the quantity come up to the preset number software will indicate that the programming quantity XXXX has been completed This function helps to save your time in counting the number of chips You may also press Reset button to initialize success number and failure number at 0 9 Installation Po
14. is software will appear on desktop We can double click it to run the software Note Run the software after proper connection of hardware so as to identify the hardware easily Interface after start of software is shown below I cixl Dle Erop Optica Kelp 2 oa gu a Pot sewo Chie Fannie hie Soweto Ean Eras stood prno Ver Read Foe Poe apa a rerea r e Progam Options 0000 IFFY SFP DESK IFFY J37FPFP JFFY SEPP IEE T F Blak S Eime Progam And Verty EEPROM 1 OOS IFFY BFF JFPF IFFY 37PF IFFY UTP AEF 7 0010 IFFY JFFF JFPPF IFFY TIF IFFY BFP IEE T 1 OOLS IFFY BFK JPPF IFES DIFP 3PFY UHR 3PFY 7 3 OOO IFFY TIFF IFFY IFS BIKE AFT BIE JPF 7 OOLS IFFY JFYF JFPF AFH DEER JIFFY IYFF IETS 1 0030 IFFF SFP IFEF AFH TIFF APY BTR IEEE J 0035 JFPFF JFFP JPPF AFH 377P JPFY SPP IETS 3 0040 IFFY SFTP JPPF IFFY BIH IFFY SPP 3PFF OTT 7 OO48 IFFY ITF IEEE FY BFPP J3PFY FPR IFFY OT 0030 IFFY SIF JFPPF IFFY TIPE IFFY UIKF IEE 7 OOSS IFFY BFK IEF IFHT DIFP 3PFY BIPP IFFY 7 ODGO IFFY TIFF IFFY IFHF BIKE ITY BIKF IEE 7 ODES IFFY JFYF IEF IFHF JYPP IETS BIKE IEE 1 1 1 1 Configastion Word UFF OSS Orr OTT a AGUA 0070 2FFF FFF JFF IFFY IYFF IFFY 3YFF IFFY 7 Uiw iD DEFFFFFFF 0078 IFFY NFP IPFF 2FFY IYFF IFFY BERR IFFY ODRO JFFF IFFP EEF IFFY BFK 3PFY 3YPP IFFY T 7 7 7 f forties 11 FS PE ELISA 2 SE LE LOGUE RE EN EN INE ED ENE IE EAE LE ee a Crarnania a Toas Passt Fal 0000 fe
15. n right diagram a 12C SPI EEPROM You may select the type to shorten the chip list BIET for fast selection of proper chip If you don t know exactly the device please select All Chip in the list of Chip Family B Select Chip The control for selection of exact chip is at Chip Selector top right of the software as shown in right M diagram If the desired chip type is not listed please change the chip type or select All Chip and try again If you can t find the desired chip to program in the list please send E mail to us We will upgrade programmer software to support the chip you desire to program based on conditions satisfying programmer hardware 3 Load File to Program Run File Load or press Load button on programming software panel to load machine code file of the chip you desire to program This programmer software supports load of BIN files generally from code recover and HEX files generally from normal program compiling This programmer software supports load of configuration bit in the file and EEPROM data Accordingly you may write configuration bit information in your source program and EEPROM data inside the chip you desire to pre program In this case HEX file compiled will contain configuration bit parameter of chip and EEPROM data This file doesn t need to reset configuration bit when programming 1 Click Load icon on tool bar or select File
16. nd address and auto increment step set to ignore high byte in auto increment to avoid effect to RETLW instruction in auto increment part of program Program supports load of HEX or BIN files available to converse BIN files to HEX format With programming data monitoring Through check summing available to find immediately if programming data is changed or not Verification and formula are subject to definition of Microchip Programmer hardware auto search when start of software no need for software setup before use easier and more convenient operation High programming success rate enough programming depth Programmable voltage electrical parameter of programming and programming algorithm satisfy the technical specifications of manufacturers Operation Instruction I Hardware Installation There is no special requirement for installation of this programmer Connect programmer to PC through serial port cable or USB cable and power up then the programmer works o This programmer supports direct USB power supply If USB cable is connected you may not connect external power However if current through USB interface is very low less than 200MA and insufficient to drive programmer connection to external power is required to enable the programmer to work regularly II Software Installation 1 Installation of Programming Software Find file QL PROGvXXen EXE under root directory of CD double click this file to
17. sition of Chip QL PIC280 Programmer Pin 1 of all chips will be aligned with pin 1 at handle of 40 pin socket QL 2006 Programmer There are many chips not aligned with pin of socket which have their own special installation positions When the chip is selected software will automatically indicate the position for chip installation on socket You may also forbid the pop up graphics of device installation by running Option Not show chip position in chip selector We can also select Option View Device Position to check the position of current chip on the socket 10 Fully Automatic Production Programming To set the availability of production programming of chip you may select Option Auto Program Tick off Auto Program to enable it valid now Auto Program button on software panel is operational When Auto Program is enabled we may program chip automatically through Auto Programming button on software panel When programming what we need to do is only to inset or take out the chip according to instruction of software status bar without pressing any button In this way production speed is improved At wait state indicating Take out Chip or Inset Chip we may single click Stop Auto Program button turns into Stop button during programming course to stop automatic programming 11 About Checksum Checksum of this software is completely subject to standard calc
18. ulation of checksum Checksum comprises program area data and configuration bit data of chip excluding user ID and calibration value of internal clock if any After editing buffer and configuration bit checksum is automatically updated After serial number auto increment checksum is automatically updated 12 About Serial Number Auto increment Programming User may program the serial number SN of device into some certain units of chip to identify and manage the device developed The initial value and start address of this serial number will be set by user Select Option Serial Number Options the following dialog will pup up Serial Humber Oj x pices gt Memory region to use seia Program Memory Data EEPROM ID M utolne Operation Formt Start Adr HEX H Hex C Dec End Adr HEX H Setting I Increasement From Hei Adr Ine Step J Ingnore Hei Byte of Word Each time program J successful after save current file go buffer OK Calcel TEST SN auto increment is valid only when Serial Number Enabled is ticked off Memory region to use serial Program Memory Select auto increment address of chip in ROM area Data EEPROM Select auto increment address of chip in EEPROM area AutoInc Operation End Adr Hex end address in chip to store SN Start Adr Hex start address in chip to store SN
19. y and convenient upgrade Two communication modes of USB and serial port convenient for application on lap top computer which doesn t have serial port convenient connection of one USB cable with computer Automatic programming function and automatic programming process enable mass production for customer s great convenience programming available on chip installation without pressing any other key Overall message indication audio plus word will enable customer well informed about operating status All operator interfaces of software in Chinese make application more accessible setup of configuration bits also in Chinese for beginner s convenience Through built in ICSP interface completely compatible with ICD interface of MICROCHIP support ICSP in circuit serial programming directly without any additional device User may program after circuit board is welded For FLASH SCM online upgrade is available Equipped with 40pin DIP socket available for direct programming of 8pin 40pin DIP chip Programming of other surface mount device SMD is available based on universal adaptor Compatible with operating systems OS including Windows98 Windows2000 NT and Windows XP Function of programming counting can preset and count the programming number Function of serial number auto increment available to set auto increment area as program area or EEPROM data area set auto increment system set auto increment start address e
Download Pdf Manuals
Related Search