FB104/FB105/FB106 FB107/FB108/FB109
Contents
1. WY fl AF e The water volume changes with the turning of lever until C Mu totally shut off I 1 Do not lift the product with the seat cover and seat open TJA NG S This may cause a mechanical trouble 2 Cannot use with the hot water which temperature is higher Prohibition than 40 C Clean and dismantlement 1 Clean the outside parts of the product Use a smooth sponge cloth with diluted kitchen detergent to clean the product Do not use the following types hydrogen chloride detergent paining thinner benzene abrasive paper polishing agent fragrance and insecticide etc Paining thinner Insecticide 3 Clean the filter and regulator If the water flow is smaller than usual 1 Clean the filter for both sides Make sure to disconnect the water supply hose during cleaning 2 Clean the regulator o ring See the step 2 on the page 5 to find how to remove and install the regulator o ring ese Braided hoses SS lt V A CA xe ac me Filt 4 Y 2 Clean the nozzle Pull out the nozzle softly and use smooth cloth sponge or toothbrush with kitchen detergent to clean the nozzle 4 Remove the main body Close the lid Push the dismantlement button and pull out the product as the arrow the figure Then the product will be dismantled 1 Lever replacement As per figure A Remove the old lever along the axis direction As per figure B insert the new lev2. 1 Dismantle the old seat and seat lid e Loose the hinge and remove the old seat and seat lid Seat and seat lid 3 Install installation template As figure install the installation template on the ceramic fake away the installation template Installation template e Second installation method 2 Install expansive nuts e As figure insert expansive nuts in the holes of the ceramic 4 Fix the adaptable panel e As figure take the adaptable panel to the holes of the ceramic Adjust position for connecting bolts and adjusting pieces make the connecting bolts aim at according expansive nuts Then fix the adaptable panel template Nut is supposed to be used for the second method 6 Install the product e Keep the fix slots under the product aim at slots on the adaptable panel Push the product to the end as figure below Then completes installation The fix slots under the product 1 Refer to first installation method step 1 and 3 Dismantle the old seat and lid Put the installation template on the ceramic 2 Refer to fist installation method step 4 Take the adaptable panel to the holes of the ceramic Adjust position of the connecting bolts with adjusting pieces Screw in the nuts form underside of the ceramic Then fix the adaptable panel 3 Refer to first installation method step 5 and 6 Complete following installation procedure Operation 1 Close the water valve and
3. N Bidet nozzle Cleaning nozzle Bowl T shaped connector TEX r Shutoff valve Water inlet hose E Components 2 Installation template 1 Main body 3 Fixing Components Expansive nuts 2 LJ LJ Sliding plates 2 Rubber gasket 2 6 Water hose 5 T shaped connector Filter Note using butterfly nuts Please choose one for specific case SK Adaptable panel 7 Installation and User Manual Installation and User Manual There are two methods for installation The way of employing expansive nuts is recommended Another way is Installation Please make sure you read the instructions carefully and install it properly Mm Cautions 1 The water pressure limit is from 0 07 to 0 8 MPa 10 to116 PSI Please use as instructed 2 The water shutoff valve should be near where the product can be installed and dismantled E Product Installation Procedure E Pre installation 1 Stick the rubber gaskets on the adaptable panel e As figure stick the rubber gaskets on the slots in the adaptable panel 2 Insert the connecting bolts in adjusting pieces e As figure insert the connecting bolts in the boles of adjusting pieces 3 Insert connecting bolts with adjusting pieces in the adaptable panel e As figure insert the connecting bolts in the boles of adjusting pieces in the holes of the adaptable panel E Installation Procedure First installation method recommended
4. MAO D Italia MODEL FB104 FB105 FB106 FB107 FB108 FB109 Installation and User Manual E Thank you for purchasing the BIDET Please read through the manual carefully for appropriate use of the product m After you read through the manual keep it at a proper place for further reference 1 Names of Parts 1 2 Installation 3 O SECRUIMIO MS Sess cio coe SoS So SS Sas a Sia 3 Installation 3 Pie installation Be2ca oor coe oes ese orem oor oro oe Ss b Installation Procedure 4 Connecting Water Hose 5 3 Operation 6 WASH 6 BIDET 6 STOP 6 4 Clean and dismantlement 7 5 Product Maintenance 8 6 Self Diagnosis and Specifications 9 Self Diagnosis and Trouble shooting 9 Specifications 9 Warranty Mi Product LZ Names of parts Z DAI Dismantlement Water inlet on the left button Water inlet on the right Seat cover Water tanks Alert sticker Lever Seat Water supply hose
5. detach water pipe from the water tank Connect the t shaped connector to the water tank Make sure that rubber packing is inserted in between e Turn the lever clockwise from the horizontal position e Nozzle for WASH moves forward and start the function e The water volume changes with the turning of lever 2 Connect the water pipe to the t shaped connector Note Please remove the regulator cover and regulate o ring under the following conditions a When the water dynamic pressure is lower than 0 05MPa especially using the family tank b When the nozzle cannot work normally and water is low 1 Take out the regulator with pliers and other tools 2 Remove the regulator cover and regulate o ring except the sealing o ring 3 Insert the regulator component into the inlet pipe Caution Must use the regulator cover and regulate o ring when the water pressure is bigger than 0 1MPa Sealing Regulate o ring e Turn the lever anticlockwise from the horizontal position e Nozzle for BIDET moves forward and start the function e The water volume changes with the turning of lever 3 Press the filter and washer at the two ends of 4 Open the water valve to check if there is any water hose into the screw tube then connect the leakage main body and T shaped connector with water hose e During wash or bidet status rotate the knob to horizontal and stop douche LT tee e Nozzle moves back to original position
6. er rib into the corresponding control valve slot The installation is completed with a click sound 3 Regulator replacement Rotate the lever in the working position clip out the regulator from the inlet tube by pliers Press the new regulator into the bottom of the inlet tube The regulator replacement is completed Then rotate the lever back to non working position Regulator Qx Product maintenance 2 Nozzle replacement As per figure A Pull out the tube and do not release then remove the old nozzle along the axis direction As per figure B insert the new nozzle into the tube along the corresponding slot The nozzle replacement is completed 4 Water hose leaking solution lf water leaks from the two ends of water hose re tighten the nuts to avoid water leaking Self Diagnosis and Specifications Mi Self Diagnosis and Trouble shooting Status Cause solution 1 Low water pressure of the unit During WASH BIDET turn the lever fast to biggest volume Water is too low during WASH BIDET When water supply pressure is lower than 0 7kgf cm2 contact 2 Low water pressure of water supply local department for water pressure question 1 Water shut off valve is turned off Turn on the water shut off valve 2 Filter net of T shaped connector is stuck Clean the filter net of T shaped connector aca ren ie 3 Filter net of water inlet hose is stuck Clean the filter net of water inlet hose 4 Noz
7. ng the product and contact the retailer or local service center
8. om the date of purchase B Notes about the warranty card 1 Please make sure that the above info is completed in the warranty 2 This Warranty and invoice are important documents for product maintenance During warranty period when the retailer or service people come for product maintenance please present the Warranty and invoice 3 This warranty cannot be reissued Keep it in a proper place C Free repairment policy During warranty period if product failure damage occurs under normal operation according to the user manual free repair service will be provided D The following repairment or maintenance should be paid 1 Failure occurs out of warranty period 2 If this warranty invoice is not presented 3 Failure damage occurs due to transportation collision of the product after purchase 4 Failure damage occurs due to natural disasters such as fire earthquake flood damage lightning or by environmental pollution gas and abnormal voltage 5 Failure damage due to user s responsibility improper repairment or reassembleing of the product 6 Failure damage due to improper cleaning of product e g improper use of detergent or cleaning method 7 Failure damage due to sand junk or other unexpected goods from water supply 8 Relocation of the product up to end user s requirement mM lo request service 1 Please recheck the user s manual 2 If failure or damage occurs after refering the manual stop usi
9. zle head is stuck Take off and clean the nozzle head 5 External water pressure is low Increase external water pressure The maximum water pressure of the unit is 0 8MPa If water supply External water pressure is too big pressure is higher than that please contact local department for water pressure question Water dropping from bowl when using the unit If any failure still occurs after above trouble shooting please contact local service A N Do not disassemble repair or remodel the unit Caution ME Specifications Classification Description Model No FB104 FB105 FB106 FB107 FB108 FB109 WASH water flow 0 35 1 8 L min BIDET water flow 0 35 1 8 L min Backflow Prevention Check valve vacuum breaker Water Supply Direct from water pipes Water Pressure Range Static pressure 0 07 0 8 MPa Dynamic pressure above 0 03MPa FB104 FB105 FB109 370X500X60mm Dimensions FB106 FB107 370X500X62mm FB108 370X480X62mm FB104 2 23 KG FB107 2 08 KG FB105 2 22 KG FB108 2 00 KG FB106 2 09 KG FB109 2 16 KG Warranty Card Dear Customer Thank you for choosing the product If failure or damage occurs please check the product based on the trouble shooting guide in this manual first If the failure damage could not be fixed please contact the retailer or local service center with proof of purchase A Related Info Name Customer Address Tel Name Retailer Date of Purchase ee Warranty time 1 Year fr
Download Pdf Manuals
Related Search