MAX512 - Net.DO Home Page
Contents
1. MAX512 Moving Light Controller PAGE 20 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 8 2 2 How to run Number of current Chase t CHASE A01 auto gt 001 1 ff Trigger mode Running Number of direction current Step Example 1 Run Chase A1 only 1 Press CHASE A to enter the state of Chase Group A Thus the number keys 1 15 are used to control Chase A 2 Press number key 1 run Chase A1 Tips e When number keys are under Swop state only one Chase can be run at one time e When number keys are under Latch state several Chases can be run at one time e Press TYPE to change the types of number keys Example 2 run Chase B5 Chase B6 at the same time 1 Press CHASE B to enter Chase state of group B Thus number keys 1 15 are for the control of Chase B Press TYPE to choose Latch state 3 Press number key 5 6 to run the needed Chase The controller can run several Chases at one time version 3 9 defaults 6 Chases If the number of running Chases is over the permitted number Chase over load will be displayed on the controller Tips When choosing a Chase if the Chase is empty that is without any Steps the LCD screen will display Step is empty 8 2 3 Check running conditions of each Steps of the Chase When running several Chases at one time the parameter displayed on the LCD screen is of the last Chase If parameter of other Chase needs change the Chase2. e When the keys 17 32 beside the group is workable the group of Faders can be used to control the value of Channel 17 32 of intelligent Fixtures X Y WHEEL e X wheel used for setting the PAN of intelligent Fixtures and Y wheel for TILT under the Manual mode e Used for adjusting the Chase Speed amp Cross under the running state e X Y wheels used for transferring and editing a very item under edit mode e X Y wheels is of dead band regulated mode that is the faster it roles the adduction will increase by degrees MAX512 Moving Light Controller PAGE 11 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 3 5 Introduction to back board port Introduction e The controller adopts two DMX512 output modules with optical isolated and the same output e The audio input socket is 1 4 monophonic socket with input line level OdB When audio device is plug in the audio source is line level input When there nothing plug in the audio source is MIC selection e Differences are found in the ports of different models of controllers please view the parameter table e When connected to the AC power please make sure the controller is connected to the protective groundwire and ensure the voltage is suitable for safety concerned WARNING POWER INPUT VGA PORT PORT1 DMX512 PORT2 AUDIO INPUT AC 100 240V CRT LCD PIN1 GND 10dB 10dB RISK OF ELECTRIC SHOCK 50 60Hz PIN2 OUT A DO NOT OPEN A 5W P
3. which needs change must be presented on the LCD screen that is it must be called then Pressing CHASE A or B then press number keys of the wanted Chase the wanted Chase can be viewed and controlled without affecting the state of the former Chase MAX512 Moving Light Controller PAGE 21 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 8 2 4 Trigger mode of Chases There are 3 trigger modes for Chase programs e Auto auto mode Chase programs are run by the values of SPEED and CROSS e Swing swing mode The Chase running speed is controlled by SWING hit the key with certain rhythm then the Chase will run with the very rhythm even if you stop hitting the key e Music music mode Chase programs are triggered by the signal of low frequency swing of music Press MODE continuously can change the Chase trigger mode Each Chase can set different trigger mode independently 8 2 5 Adjust the SPEED 8 CROSS under the Auto mode Speed The running speed of current Chase Adjust range 0 100 0 the slowest 100 the fastest Corresponding time 180 0 03s each Chase Step Cross The FADE time between Chase Steps range from 0 to 100 0 the lowest 100 the fastest Example Cross 60 that is use 40 of the time for cross from former Step to later one then the later Step will remain in the left 60 of the time Notice Cross can be only used in Auto mode Adjusting methods Pressing TIME key
4. INS OUT AC power input DMX512 output Audio input MAX512 Moving Light Controller PAGE 12 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 4 Settings of intelligent Fixtures 4 1 Know more about your intelligent Fixtures When programming the intelligent Fixtures user s guide should be at hana for the number of channels and the control parameters varies for different intelligent Fixtures For example the address code the functions of each control channel 4 2 X Y pan tilt Channel Analysis X channel controls left right PAN movement of the intelligent Fixtures while Y channel controls up down TILT movement To make the X Y wheels fit for any intelligent Fixtures which adopt DMX512 protocol receiving address code of every intelligent Fixture must be set in advance then the X Y channel of each intelligent Fixture should input into the controller according to the serial number If X Y gradual movement CROSS and Shape track effects are wanted the X Y of the intelligent Fixtures must be set in advance 4 3 Allocation of DMX512 address amp Setting of X Y 4 3 1 Fixed allocate addresses of intelligent Fixture e The origin setup of the controllers is set for 30 intelligent Fixtures with 16 channels for each Fixture The method of data initializtion is in chapter 11 e The fixed intervals for each intelligent Fixture s DMX512 address are as follows Chart 1 Setting of the intelli
5. M CARD onto the controller 1 Insert the MEM CARD under running state the blue indicator light up 2 Press LOAD key 3 Press File2 to choose File 2 After loading the controller will display complete 4 Pull out the MEM CARD the indicator turn out the controller returns to the running state MAX512 Moving Light Controller PAGE 28 Net DO Lighting Control Equipment Co Ltd http www netdo com cn Tips e During the period of loading File the blue indicator will flicker the progress will be displayed on the LCD e During the period of loading Files don t pull out the MEM CARD or the loading will fail e After the loading is ended the old data of the controller will be overlaid by the new data The controller will run according the new data 11 Initializtion of data Steps 1 Pressing PROGRAM and switch on the power till LCD screen displays PASSWORD 2 Press number keys 1 2 3 15 at the same time 3 The system will restart automatically after initializtion Notice After the initializtion all data will return to the origin factory state Special function Notice Please keep this paper If you forget the password please contact with the retail store to ask for help A The steps of using password to start 1 Pressing PROGRAM and switch on the power till LCD screen displays PASSWORD 2 Press number keys 1 2 7 8 at the same time B The steps of canceling the star
6. MAX912 USER MANUAL Version Number 3 9 Net DO LIGHTING CONTROL EQUIPMENT CO LTD http www netdo com cn Net DO Lighting Control Equipment Co Ltd http www netdo com cn Contents o RR O O RARO ARO ONO 4 LME OO A AA E 4 1 2 Specification parametro de ii id ta 5 O o lt csccccevecececesecevecevecevecesecevacevecevecesecevacevecevesecdenedevacevesevadesevevadevadevaceseveadevedcesavevaievederete 6 PES ale Canton o leelo eel alo ll EAE 6 22 CODECS powers s ietsevel toda ios its 6 2 3 Connect intelligent Fixtures with digital Dimmer pp 6 2 4 Audio signal SOUTCS necia aida 7 E Fo AN 8 A Slee eed Avis eine Aer els tae an ee A eles 8 3 2 Wsetull plossaryict cies Seri Reeve Mahi ee A ae a 9 3 3 Keyboardsiic iscsi este A in deed hha aed eae aoe 9 3 4 Fader ea 11 3 5 Introduction to back board pOTt oooooooccnonccconcccononcnonncnonnononcncononcnnnnonon nono n nn non nn cnn nncnnnncnanno 12 Hb Seis tic os AAN 13 4 1 Know more about your intelligent Fixtures pp 13 4 2 X Y pan tilt Channel Analysis ooooonooccnonccconcnconnnononnononncnoncnnononconononn non n non nnnan cnn nenonns 13 4 3 Allocation of DMX512 address amp Setting Of X Y c oooonocccnonccconcccononononnononcnnonononnnncnnnncnonnno 13 4 3 1 Fixed allocate addresses of intelligent Fixture ee 13 4 3 2 Dynamically allocate addresses of intelligent Fixtures pp 14 4 3 3 Methods amp steps of X Y settings ee 14 S Merval moodle ot tei
7. Use X wheel to change the value of Speed Use Y wheel to change the value of Cross CHASE A01 sp 80 c 100 1 1 Speed value Speed Cross time Cross MAX512 Moving Light Controller PAGE 22 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 9 Shape track The function of Shape track is convenient for users to control intelligent Fixtures to have graphic movement such as circle line square on X Y tracks The function enables multi intelligent Fixtures to produce various dynamic effects which are composed of different Shapes Take making a circle for example if Chase program is used for making a circle each point of the circle needs an individual Step and the resolution is limited Besides the size of the circle could not be changed for composing with other Shapes But with the Shape track function only with the parameter of the circle s speed size direction input it will have the effect 9 1 Shape track generator The Shape generator can produces Shape tracks of different Shapes various sizes and speeds for intelligent Fixtures The controller has several individual generators which can work at the same time Each generator can run several intelligent Fixtures producing pattern effects of several lights phase excursion The currently version of system s software offers 50 generators as follows e 12 circle circle e 8 fader circle fader amp c e 5circles ranged in triangle shape
8. X FIXTURES 30 MAX FIXTURE CHANNELS 32 DIRECT CALL OF SCENES 30 CHASE PROGRAM 30 CHASE SPEED RANGE 0 03s 180s CHASE TRIGGER MODE Auto Music Swing CHASE DIRECTION CONTROL Forward Inversion SHAPE CONTROL Yes up to 50 SHAPE generators LCD MONITOR Yes FLASH CARD PORT Yes MUSIC SIGNAL INPUT Unbalanced line level input 1 4 Monophonic audio input MIC input DMX512 OUTPUT PORT Optical isolated output port ELECTRIC POWER SOURCE Switch mode power voltage range 90 250VAC frequency 50 60 short circuit protection amp overload protection POWER 5W SIZE 485mm x 267mm x 85mm MAX512 Moving Light Controller PAGE 5 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 2 Installation MAX512 Intelligent Fixtures Controllers packing chest contents items as following e One MAX512 Intelligent Fixtures Controller Ps to confirm the model of the controller please check the model number and software version number displayed on the LCD monitor when run the controller e One feed cable one user s guide The controller is of international 19 construction standard of installation It can be in board installed or installed on the 19 stander or machine cabinet 2 1 Safety caution e The controller must be connected with the protective groundwire to ensure safety e The intelligent Fixtures controller is sophisticated electronics Please m
9. avaeeseisveeetss 28 28 10 3 Load File dr td ica 28 o on o e AN 29 MAX512 Moving Light Controller PAGE 3 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 1 Summary 1 1 Function MAX512 Intelligent Fixtures Controller can connect up to 30 intelligent Fixtures with a maximum of 32 Channels each The new technology of the core microcomputer has strengthened the functions They are more humanized DMX512 1990 standard 512 DMX channels output with optical isolated Up to 30 intelligent Fixtures may be connected with a maximum of 32 channels each Uses can allocate DMX channel to each intelligent Fixture dynamically The X Y channel of different intelligent Fixtures can be controlled by modulation Wheel Up to 50 SHAPE generators SHAPE track control is provided to control such effects as circles lines and shapes like 8 etc 30 Chases up to 100 Steps each Trigger mode selectable Music synchronously Auto Manual speed 6 Chases 30 Scenes operated at the same time At most 30 intelligent Fixtures can be selected simultaneously Flash card slot is provided each Flash card can record the whole data of controller LCD display with backlight Power supply AC 90 250V 50 60Hz MAX512 Moving Light Controller PAGE 4 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 1 2 Specification parameter DMX512 1990 OUTPUT SIGNAL Yes CONTROLLABLE DMX512 CHANNEL 512 MA
10. d Use 2 Steps to move the centre of the circle then call the same circle generator in the 2 Steps parameter is up to you BRE Oy eee E CHASE STEP1 o gt Q ster FIXTURE 1 PEETERS Example 4 Use several intelligent Fixtures to produce an up down waving wave 1 Select 9 intelligent Fixtures under Manual mode No need to select continuous numbers but the direction of the Fixtures should be the same Set the X Y of chosen Fixtures range the luminous spots in a line Press PLAY to enter Shape edit state indicator flickers Use X Y wheel to select a Shape Yline 1 Press Speed Size key e Use X wheel to change the value of Speed such as 40 e Use Y wheel to change the value of Size such as 60 6 Press Offset Dir key e Use X wheel Change the Offset Offset 25 Use Y wheel select the DIR 7 Press PLAY to escape from Shape edit state Dra oo EEE Oo O EEE POLO yy ue 2 o Tips If the Shape uses horizontal line Xline an effect of left right movement of lights will be produced ak WON FIXTURE 1 OFFSET MAX512 Moving Light Controller PAGE 27 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 10 Load and save MEM CARD For different users and various usages the needs of controller data are different Besides the set data need prevention from being changed MEM CARD Memory card offers backups of data The controller offers a slot of MEM CARD for us
11. eed 3 3 Keyboard FUNCTION KEYS CHASE Function key for Chase Group A controls Chase program A1 A15 Group B controls Chase program B1 B15 1 Used for choosing Chases When button down The controller is in Chase running state with number keys 1 15 to different Chases 2 Used for checking the parameter of Chase Press a number key to the very Chase when pressing CHASE key the parameters of the very Chase can be viewed and transferred into without affecting current state SCENE Function key for Scenes Group A control Scene A1 A15 Group B control Scene B1 B15 When button down the controller enters the state of controlling Scenes meanwhile number keys 1 15 are for choosing Scenes Preset Scenes are divided into Group A and Group B with 15 preset Scenes each FIXTURE Function key for Manual control Group A control Fixture A1 A15 Group B control Fixture B1 B15 When buttons down The controller enters the state of Manual with number keys 1 15 for choosing intelligent Fixtures Use key A B with number keys can select 30 intelligent Fixtures Group A is for the former 15 intelligent Fixtures Group B is for the later 15 Number keys 1 15 There are 15 number keys on the controller Under different states of different function keys the keys give different effects For example when the LED of a number key is on it means it s outputting a very Scene or a very Chase program CONTROL KEYS CLEAR Clear key Clear
12. empty the screen will display P CHASE A10 step is empty 4 Press STEP to adda Step Current Chase number 4 P CHASE A10 tol 001 st 1 The total Steps current Step means the last Step Ps STEP canbe used to select Steps e f current Step is the last Step of the Chase will be displayed Example The last Step of the Chase is Step 10 st 10 will be displayed on the screen e Pressing STEP Steps can be chosen automatically If anew Step is wanted move to the last Step which is displayed with press STEP a new Step with the same content is added MAX512 Moving Light Controller PAGE 18 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 5 Use number keys 1 15 to select intelligent Fixtures use Manual mode set the Channel values of all the intelligent Fixtures Shape generator can be used as well 6 Repeat steps 4 5 edit next Chase Step 7 Press PROGRAM escape from edit state or repeat step 2 6 to edit another Chase program Tips e When press STEP to add a Chase Step the system will add a Step after the former one and copy the content of the former one Thus only with some changes of values a new content is edited e Use COPY to copy the current Step into another Step Example copy Step 1 into Step 8 Choose Step 1 Pressing COPY and choose Step 8 done e Press DELETE to delete current Step pressing the button without loose can continuously del
13. ers to save and load their own data Each MEM CARD has 2 File Each File can save and record all data from the controller 10 1 Use of MEM CARD e One side of MEM CARD has metal plate please don t touch or dirty the metal plate e When the card is needed please insert the MEM CARD into the slot with the side of metal plate on the left The end near metal plate should enter the slot first e Ifthe MEM CARD is correctly inserted the blue indicator beside the slot will be on If the indicator doesn t light up it might be the MEM CARD is problem Example the metal plate is dirty or the card is not the component card of the controller or the MEM CARD is false inserted The MEM CARD is thin please not bend it hard 10 2 Save File Steps Example Save controller s data into File 2 of the MEM CARD 1 Insert the MEM CARD under running state the blue indicator light up 2 Press SAVE key 3 Press File2 to choose File 2 After saving the controller will display complete 4 Pull out the MEM CARD the indicator turn out the controller returns to the running state Tips During the period of saving files the blue indicator will flicker the progress will be displayed on the LCD e During the period of saving files don t pull out the MEM CARD e After the saving is ended the old data of the target File will be overlaid by the new data Each MEM CARD can store 2 Files 10 3 Load File Steps Example Load File 2 of the ME
14. ete several Chase Steps MAX512 Moving Light Controller PAGE 19 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 8 Running 8 1 Run Scenes Example 7 Run Scene A1 only 1 Press SCENE A to enter Scene state of group A Thus number keys 1 15 are for the control of Scene A 2 Press number key 1 to run Scene A1 Tips e When number keys are under Swop state only one Scene can be run at one time e When number keys are under Latch state several Scenes can be run at one time e When number keys are under Flash state the indicators of Latch amp Swop are off At this time pressing number key with output and losing without output e Press TYPE to change the types of number keys Example 2 run Scene B5 Scene B6 and Scene B7 at the same time 1 Press SCENE B to enter Scene state of group B Thus number keys 1 15 are for the control of Scene B 2 Press TYPE to choose Latch state 3 Press number key 5 6 7 to run the needed Scenes 8 2 Run Chases 8 2 1 Set the FADE mode for channels When chase running there are 2 FADE mode for channels e Only X Y Only X Y channel as Fadeable other channels set as Instant Default e AllCH All channels can be set as Fadeable Setup Steps 1 Under running state keep PROGRAM key pressed for 3 seconds to convert the FADE mode PROGRAM Fade only X Y 2 Press PROGRAM key to quit 3 Repeat Step 1 2 to convert the FADE mode again
15. ged The remaining state can be transferred into choosing state by pressing the very key to make the indicator on 3 Use CH1 CH16 Faders to set the Channels value use wheels to adjust the X Y position Shape generator can be called at the same time 4 Press the very number key for the chosen intelligent Fixtures again the indicators MAX512 Moving Light Controller PAGE 15 Net DO Lighting Control Equipment Co Ltd http www netdo com cn will be flickering that means they are under the remaining state 5 Repeat steps 2 4 set other intelligent Fixtures 5 3 Cancel the Manual run of intelligent Fixtures Under the Manual mode of the intelligent Fixtures press CLEAR to cancle the Manual runnings without saving the Channel values MAX512 Moving Light Controller PAGE 16 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 6 Edit of Scenes To set suitable value for the brightness color X Y Channels Shapes of every intelligent Fixture the needed light beam pattern will be displayed in the air Accompanied with the call of Shape generators a Scene is produced Each Scene is a combination of the set Channel values of intelligent Fixtures The controller can store 30 Scenes which can be run as you wish 6 1 Important tips To run multiple Scenes and multiple Chases at one time the different values of the same control Channel will be expressed according to HTP technique 6 2 Edit records steps of Scene
16. gent address switch when fixed intervals are acquiescent arranged Fixtures NO address Fixtures NO address A1 1 B1 241 A2 17 B2 257 A3 33 B3 273 A4 49 B4 289 A5 65 B5 305 A6 81 B6 321 A7 97 B7 337 A8 113 B8 353 A9 129 B9 369 A10 145 B10 385 A11 161 B11 401 A12 177 B12 417 A13 193 B13 433 A14 209 B14 449 A15 225 B15 465 MAX512 Moving Light Controller PAGE 13 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 4 3 2 Dynamically allocate addresses of intelligent Fixtures Uses can allocate DMX channel to each intelligent Fixture dynamically A maximum of 30 Fixtures with up to 32 channels each can be chosen 4 3 3 Methods amp steps of X Y settings Press PROGRAM to enter edit state the indicator on 2 Double click FIXTURE A or B key to enter setting state of intelligent Fixtures Group A or B 3 Use number keys 1 15 to select the Fixture wanted 4 Use X wheel to select items edited The items are in several pages it will go to adjacent page when the moves to the right left edge Use Y wheel to set the very value 6 Repeat step 3 5 to set other intelligent Fixtures 7 Press PROGRAM to escape from edit state Examples A02 Fixture with 12 Channels X axis on Channel 5 Y axis on Channel 7 The setting screen of intelligent Fixtures total number of Channels Setting state of Fixtures More inf on the right 4 y P FIXTURE A02 addr 013 ch 12 gt 1 1 DMX addres
17. he X Y wheel the Speed and Cross of current Chase can be adjusted BLACKOUT Blackout key or cut light key To turn all lights down EDIT KEYS PROGRAM Program edit key When in running state press the button to enter the edit state The LED indicator will flicker COPY DELETE Copy and Delete key Under the state of Chase programs the above two keys are used for copy paste and delete MAX512 Moving Light Controller PAGE 10 Net DO Lighting Control Equipment Co Ltd http www netdo com cn STEP Chase Step number minus plus key When a Chase program is edited is used to change the Step number of the current Chase program KEYS FOR SHAPE TRACKS STOP Stop key for Shape track Used for stop all the Shape generators restore intelligent Fixtures to X Y origin point PLAY Run and edit key of Shape tracks Used for running the Shape track generator and entering the edit state of Shapes Speed Size Speed of Shape Size of Shape key Offset Dir Offset of Shape phase Direction edit key VIEW Calling key of Shapes Used for viewing the calls of Shapes DATA CONTROL KEYS LOAD Key for loading data Load data from MEM CARD to the controller SAVE Key for saving data Save data of the controller into MEM CARD 3 4 Fader and Wheel CH1 CH16 Group of Faders e When the keys 1 16 beside the group is workable the group of Faders can be used to control the value of Channel 1 16 of intelligent Fixtures
18. he position of the circle s centre Press PLAY to enter Shape edit state indicator flickers Use X Y wheel to select a Shape circle1 Press Speed Size key e Use X wheel to change the value of Speed AS bs such as 40 T e Use Y wheel to change the value of Size such as 25 6 Press Offset Dir key i CENTRE O iia e Use X wheel Change the Offset Offset 0 Use Y wheel select the DIR 7 Press PLAY to escape from Shape edit state ak WN gt Example 2 Use 4 intelligent Fixtures to draw a circle 1 Select four intelligent Fixtures under Manual mode No need to select continuous numbers but the install direction of the Fixtures should be the same 2 Set the X Y of chosen Fixtures make all the luminous spots be at the same position the circle s centre 3 Press PLAY to enter Shape edit state indicator flickers 4 Use X Y wheel to select a Shape circle2 5 Press Speed Size key e Use X wheel to change the value of Speed such as 40 e e Use Y wheel to change the value a of Size such as 25 6 Press Offset Dir key e Use X wheel Change the Offset FixturE3 CENTRE O RES Offset 25 FIXTURE 2 e Use Y wheel select the DIR 7 Press PLAY to escape from Shape edit state O FIXTURE 4 MAX512 Moving Light Controller PAGE 26 Net DO Lighting Control Equipment Co Ltd http www netdo com cn Example 3 move when drawing circle To have the effect call Shapes in Chase can be use
19. i senit hin AA 15 3 1 CHANNEL Faders 8 Wiee lenorion s nnen ANERE AEAT E AAAA NAAA 15 5 2 Manual run of intelligent FiXtureS 4 15 5 3 Cancel the Manual run of intelligent FixtureS pt 16 O ocn nconcon o con nooo econ nc one cane can econ e sona cone cone sona cone cone sone sones donesonasnos 17 0 1 Important ipsi ie a S E a 17 6 2 Edit records steps of Scenes ica as 17 6 3 Copy OSCE iO Ei 17 7 Ca o AN 18 TAEdt the Chase PEO A A AS AA ed 18 o 026 0c consconesedscedecoascoaeseascodecoascoaesoasodecotscoaesoedonseodesoteouedonceodedotsdeuededseatecetedetedsetedensdetesetes 20 20 20 8 2 1 Set the FADE mode for channels pp 20 8 2 2 HOW tO NS 21 8 2 3 Check running conditions of each Steps of the Chase ppp 21 8 2 4 Trigger mode Of ChAaSeS et 22 8 2 5 Adjust the SPEED amp CROSS under the Auto mMode c eee 22 o AAG sccscenscenecenscenecenscenesenscenesenscenscenecenecenesenasenesenesenesenesenasenecenedonacenesobedensadonedonedones 23 9 1 Shape track generator Ne 23 92 Gallkand edit of Shapes lt 23 MAX512 Moving Light Controller PAGE 2 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 9 3 Stop SF 25 9 4 Cancel intelligent Fixture s call of Shape pp 25 9 5 View the call of Shapegs 4 25 9 6 Skillsof sing APS cdta aid E e E S e 26 o MEMO AO 28 10 1 Use of MEM CARD ic csccesccstvcicesscuiesiestadasisebageseueusdaseestacessdevsdarveessysvuseineeniesteu
20. ind the dust and moist 2 2 Connect the power Please check the supply power ensure it in the suitable voltage range of the controller The plug must connect with the protective groundwire to ensure the safety 2 3 Connect intelligent Fixtures with digital Dimmer There are two DMX512 XLR D3F output sockets on the rear panel of the Controller Pin 1 for signal ground Pin 2 for negative and Pin 3 for positive e DMX512 cable is screened twist wire Each end of the cable should be joined to XLR plug by user Pin 1of XLR plug is connected to the screen net of the cable Two wires of twist distinguished by different colors are connected to Pin 2 and Pin 3 of the plug respectively Please do not confuse SCREENED TWIST LINE LIGHTING CONTROLLER DMX512 OUTPUT E FIXTURE 120 OHM TERMINAL RESISTANCE Pin number Cable conductor 1 Shield 2 Negative pole 3 Positive pole MAX512 Moving Light Controller PAGE 6 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 2 4 Audio signal source e The audio signal can select from sound mixing console and line level output of other audio devices or MIC selection The controller can automatically pick the part of low frequency swing as the music trigger signal of Chase program e One unbalanced monophonic audio input locates in the back board the range of line level input is 10dB 10db When audio device is plug in the audio source is l
21. ine level input When there nothing plug in the audio source is MIC selection MAX512 Moving Light Controller PAGE 7 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 3 Operation Guide 3 1 Panel plot did A LNOS MEM CARD o o gt ou o A A PEER D gt ofj t IiI POWER POWER 10 0 VIEW O CH16 132 PLAY Speed Size Offset Dir Net DO O CH15 131 O CH14 130 CONTROL EDIT memm mu SHAPE CONTROL g 1 AAA AAN AO AO TYPE PROGRAM BLACKOUT Latch F F F Swop d y d MODE SWING gt Auto Q E F F Swing Music DELETE STEP PEER lo D AAN D gt BORER one MITT It IEEE ARANA EE CLEAR m 8 o A FIXTURE B SET X Y _ 7 a 15 mu 6 m 14 A SCENE B p F aa MOVING LIGHT CONTROLLER E 5 FILE 2 mm 11 FILE 4 FIXTURE CHANNEL gt gt gt mu 3 A CHASE B p F y y E 2 Ha A 10 13 y LOAD FILE 3 m 1 mm 9 4 a 12 Ges NUMBER SAVE SAULR SVT WAON O a MAX512 Moving Light Controller PAGE 8 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 3 2 Useful glossary e Scene the concourse of Channel values of intelligent Fixtures X Y position Shape track brightness gobo color etc e Chase program every Chase program is composed of some Chase Steps and every Step is a Scene ind
22. olled by Channel Fader CHANNEL and X Y wheels 5 1 CHANNEL Faders amp Wheel The channel value of intelligent Fixtures is set by channel Faders CH1 16 When the keys 1 1 6 beside the group is workable the group of Faders can be used to control the value of Channel 1 16 of intelligent Fixtures When the keys 17 32 beside the group is workable the group of Faders can be used to control the value of Channel 17 32 of intelligent Fixtures The X channel of intelligent Fixtures is set by X wheel while Y wheel for Y Channel the value range of the wheels is 0 999 representing the entire movement range of the X axis and Y axis When the X Y Channel is under the control of wheels the very Channels Faders are automatically locked Only using wheels can change the X Y position of the intelligent Fixtures 5 2 Manual run of intelligent Fixtures For different kinds of intelligent Fixtures only one kind can be manually set at one time It s a common run 1 Press FIXTURE A or B to enter the manual state 2 Press number key 1 15 to select one or more intelligent Fixtures Only the same type of intelligent Fixtures can be selected at the same time The controller will automatically transfer into the current type of intelligent Fixtures the former ones will be under the remaining state The Channels value of intelligent Fixtures under the remaining state whose indicators flicker slowly won t be chan
23. s 1 According to the Manual mode of intelligent Fixtures select intelligent Fixtures and set the Channel values and X Y position Shape can be called at well Press PROGRAM to enter edit state the indicator flickers Press SCENE A or B to enter Scene choosing state Use number keys 1 15 to select the Scene you want to save 91 5 WAIN The controller will escape from the edit state after saving Scenes P SCENE select Scene Example Save the running of the intelligent Fixture as Scene A10 Press PROGRAM then press SCENE A then press number key 10 done 6 3 Copy of Scenes Example Copy Scene A2 into Scene A10 1 Firstly present Scene A2 2 Press PROGRAM press SCENE A then press number key 10 done MAX512 Moving Light Controller PAGE 17 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 7 Edit of Chase program The controller can store 30 Chase programs with up to 100 Steps each The Steps of the total Chase program is 360 Ver 3 8 which is dynamic allocated by the controller automatically The Chase programs is composed of several Steps Steps are similar to Scenes 7 1 Edit the Chase program 1 Press PROGRAM to enter edit state indicator flickers PROGRAN 2 Press CHASE A or B Select a group of Chase A or B 3 Use number keys 1 15 to select the number of the Chase wanted Example If you want to edit Chase A10 press number key 10 If the Chase program is
24. s total channels of the Fixture of the Fixture The setting screen for X Y Channel P FIXTURE lt X 05 Y 07 1 1 channel of X channel of Y Tips e Notice Changes of total number of Channels will affect the first DMX address of intelligent Fixtures Please check whether the DMX addresses of each intelligent Fixture is right with the controllers after changing Channel s number e If the total number of DMX Channel is over 512 the controller will automatically shield the intelligent Fixtures with over Channels MAX512 Moving Light Controller PAGE 14 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 5 Manual mode of intelligent Fixtures Set Channel value of brightness X Y Shape of a pointed intelligent Fixture under the Manual mode The items controlled by each Channels are different to different intelligent Fixtures Knowledge of details about the items and Channels is necessary for skillful management Manual mode is adopted as the most advanced mode the chosen intelligent Fixture will automatically escape from the current Scene and Chase when transferred into Manual mode Manual run is also the basic run It can store the Scenes It is also the basic run for Chase program edit FIXTURE A B used with number keys 1 15 can enter the function of choosing Fixtures When the indicators of number keys are on the very intelligent Fixture is under choice mode The chosen Fixture can be contr
25. the whole choice of current number key MAX512 Moving Light Controller PAGE 9 Net DO Lighting Control Equipment Co Ltd http www netdo com cn TYPE Key for choosing the type of number keys Independently set the type of number keys Latch Swop Flash under some state e Latch Multi number keys can be choose at the same time Latch indicator light is on e Swop Only one number keys can be choose at the same time Swop indicator light is on Flash At this time pressing number key with output and losing without output When the indicators of Latch 8 Swop are off Press TYPE continuously the type of number keys will change repeatedly The types of number keys under different state STATE LATCH SWOP FLASH Vv Vv x CHASE A B SCENE A B v Vv Vv FIXTURE A B v x x MODE Key for choosing trigger mode of Chase There are 4 mode totally auto mode The Chase running speed is controlled by Speed e swing mode The Chase running speed is control by Key SWING e music mode Chases are music swing triggered Press MODE continuously can change the Chase trigger mode lt 4 SWING gt Key for choosing direction of Chases and swing When running a Chase the key is used for change direction of the Chase When the Chase mode is under swing mode hit the key with certain rhythm then the Chase will run with the very rhythm TIME Controlling key for the Chase running time When pressing the button with the use of t
26. ther intelligent Fixtures 7 Press PLAY or other keys to escape from Shape edit state the calls of Shapes will be confirmed and run continuously Indicator of PLAY on Tips Shape edit such as adjusting speed or sizes will affect all Fixtures the Shape uses no matter whether the Fixtures are being chosen That is if you want to use a new circle generator when there are other Fixtures working of other direction or speed you should call a new Shape for each change and use the changes in the corresponding Fixtures 9 3 Stop amp run the Shapes Press STOP very Shape generator will stop all intelligent Fixtures will return to their X Y origin point Then press PLAY the indicator of PLAY on with all Shapes run again 9 4 Cancel intelligent Fixture s call of Shape Call the Shape generator named 0 Null 9 5 View the call of Shapes Press VIEW LCD screen will display the number of used Shape generators Example To view which generators are used in Scene A2 1 Select Scene A2 under Scene state only Scene A2 is presenting 2 Press VIEW LCD screen will display the number of the used generators Tips When the indicator of VIEW is on there must be calls of Shapes being run MAX512 Moving Light Controller PAGE 25 Net DO Lighting Control Equipment Co Ltd http www netdo com cn 9 6 Skills of using Shapes Example17 Use intelligent Fixture 1 to draw a circle Select Fixture 1 under Manual mode Set the X Y origin point t
27. thr amp c e 5 8 shape eight e 5Xline Xline e 5Yline Yline e 5 squares square e 5triangles tri Tips The mechanical features of intelligent Fixtures may cause changes of shapes when the Fixtures are vertical For example the circle might become 8 shape Some intelligent Fixtures responding speed might be so slow that the shapes will have a little change An intelligent Fixture with faster responding speed will produce better shapes 9 2 Call and edit of Shapes Shape generator can be used under Manual mode Scene and Chase to produce X Y Shape tracks automatically In Manual mode the call of Shapes is basic skill Call Shapes in Scenes Record the Manual running with calls of Shapes into the preset Scene the corresponding Shape will automatically call whenever the Scene is run MAX512 Moving Light Controller PAGE 23 Net DO Lighting Control Equipment Co Ltd http www netdo com cn Call Shapes in Chases Add calls of Shapes into Steps under Chase edit state the corresponding Shape of each Step will be run automatically when running the Chase Manual calls of Shapes 1 Select intelligent Fixtures wanted under Manual mode 2 Set the X Y origin point the position of a Shape centre of each intelligent Fixture 3 Press PLAY in Shape edit mode The indicator will become flickering Then use X Y wheel to select the Shape generator wanted When the name of the Shape generator is 0 Null it s an empt
28. ting password Repeat the above two steps When the password is enabled every time when the controller is started the password is needed Press number keys 1 2 7 8 at the same time Net DO LIGHTING CONTROL EQUIPMENT CO LTD http www netdo com cn MAX512 Moving Light Controller PAGE 29
29. y call of Shape This call can be used to delete other calls of Shapes SHAPE 1 circle1 T Name of Shape generator 4 Press Speed Size to change the Speed and Size value of current Shape if wanted Indicators on SHAPE sp 100 si 100 j 1 Speed Size e Use X wheel to adjust Speed sp Use Y wheel to adjust size si Speed is the speed of running Shapes the larger the value the faster the speed e Size is the size of Shapes for example how large a circle is how far a light beam should move etc 5 Press Offset Dir to change Offset and direction if wanted indicators on SHAPE of 100 dir gt 1 1 Offset Running direction MAX512 Moving Light Controller PAGE 24 Net DO Lighting Control Equipment Co Ltd http www netdo com cn e Use X wheel to change Offset use Y wheel to change direction eo Offset is offset of a Shape that is to set different positions of different intelligent Fixtures in a Shape For example when a circle of 50 offset is set Fixture 1 will be the beginner Fixture 2 will be in the semi circle behind it and Fixture 3 will be in the position of Fixture 1 When a circle of 25 offset is set Fixture 1 will be the beginner Fixture 2 in the quart circle behind it Fixture 3 in the quart circle behind Fixture 2 Fixture 4 behind Fixture 3 and a Fixture 5 in the position of Fixture 1 etc e DIRis the moving direction of Shapes 6 Repeat step 1 5 edit o
Download Pdf Manuals
Related Search