RGE – 2 Leg Base
Contents
1. If the table still does not respond the handset unit may have triggered the overheating protection or the intermittency protection Please wait for at least nine minutes and try again before proceeding with other measures If a control unit must be replaced it must first be reset before it can be used To do this follow these steps 1 Press and hold Up and Down button simultaneously for 7 seconds 2 Lower table to lowest point by pressing Down button 8 Table is ready to use Should the table still not work as intended after taking these measures please contact your vendor for further assistance For instructions on the installation and care of the desktop please follow the instructions from the manufacturer 2 2 Care Instructions frame Clean the frame by wiping it down with a microfiber cloth moistened with a standard household cleaning solution Never use solvents or abrasive or corrosive compounds Mounting Guidelines 3 1 Assembly Instruction Assemble the frame according to the assembly instructions page 8 Motor Cable ae Make sure to ask your desk vendor for an approved combination of desktop and frame Always check desktop thickness against the length of the mounting screws before mounting the desktop to ensure they are appropriate and not long enough to protrude through the top surface once screwed in Connect the two motor cables and the cable from the power supply to the handset unit Take care to rou2. MAYLINE USER MANUAL ASSEMBLY INSTRUCTIONS RGE 2 Leg Base Bifma Range Height Adjustable Table Contents 1 important 3 1 1 IMPORTANT SAFETY INFORMATION 3 T2 WISER INFORMA THONG EN 5 VOW 51s Rel 5 2 Maintenance Se 6 PA AEP 6 2 2 CARE INSTRUCTIONS FRAME use one A 6 3 Mounting GuidelineS sessesesesessssesesesssosoecesssssosoesesssosossessssssesesseseo 7 8 LASSEMBIY INSTRUCTION 7 4 Assembly Instructions csscscsccscsccccsccccsceccscsccccsccccsceccscescccececcscecens 8 4 1 BASE AND HARDWARE 8 ADA E AS SEMBE 9 M3 ASSEMBLY DETAILS 10 11 DU EEEE inne heeae dan nomen AS E 11 52 CONNECTING GON TROL 11 523 RESETTING UNIT ONIFIRST USE a 11 5 4 RESETTING AFTER REPLACING CONTROL UNIT ccecccccccs
3. though crossbar and attach to handset Attach Cable Ties 8 to desired locations on the underside of the top for cord management 9 Using one person per side carefully rotate table onto the base Plug power cord into handset and then into wall outlet See Section 5 3 for setting up handset for first time use Note If optional Mayline Keyboard Platform 19503ATW was ordered please refer to the Assembly Instructions provided with that hardware bag mae ape om Crossbar Cord Passage Frame Alignment Hole Assembly Instructions Base Top 4 3 Assembly Details Detail 1 Crossbar Attachment Detail 2 Crossbar Cord Passage 10 Control System 5 1 User Manual AR Note you must read the user manual carefully before installing or operating the COMPACT control unit 5 2 Connecting Control Unit 1 Mount the control unit to the desktop in the desired location 2 Connect the motor cables 3 Connect the power unit to the control unit and the power outlet 4 Remember to reset the unit on first use 5 3 Resetting Unit On First Use Before the table can be used the control unit must be reset to establish the lowest point of the table This is achieved by first lowering the table as far as it will go Until this is done it will not be possible to elevate the table A RESET UNIT ON FIRST USE 1 Lower table to lowest point by pressing Down button 2 Table is ready t
4. csccscecccceaceacccescsacecencecesseacess 12 SS INSTALLATION HANDSET UNIT nob sa radiates 13 Important Information 1 1 Important Safety Information Danger Make sure to read all relevant instructions and safety warnings before using the table WARNING During the raising or lowering of the table there exists a risk of squeezing or pinching related injuries occurring Please note the following There exists a risk of squeezing between the moving desktop and fixed objects The necessary safety margins depend on the greatest type of injury risk that can be predicted Where there exists a risk of squeezing fingers use at least a 1 5 safety margin and for body or head especially where children may be present a minimum of 16 Under no circumstances put your fingers on the desk legs while operating desk upwards or downwards During the lowering or raising of the desktop the operator must ensure that no person or object risks being harmed by the operation This tag enclosed in packaging is to be put on the desktop by the installer after assembly This tag should be removed by the final user Do not remove during installation For safe and correct use of this electrically operated product please review the user manual rior to operating The manual may be located under the work surface Please put this tag on desktop after assembly Important Information Caution Do not open hand
5. garding its use by a person responsible for their wellbeing Children should be monitored at all times to prevent them from playing with the table Danger Any changes or modifications to the electric control unit are strictly forbidden and voids warranty 1 2 User Information The table is suitable for household and public occupancies use The motors may only be used continuously for 1 minute at a time after which they must be left inactive for nine minutes before they can be used again The control unit regulates this automatically FOR COMMERCIAL AND HOUSEHOLD USE This furnishing has not been evaluated for flammability or cigarette ignition resistance 1 3 Before You Start Make sure that there is nothing blocking the travel of the desk in the space where it will operate Before first use the control unit must register the lowest point of elevation reset To do this simply lower the table to the lowest position by pressing and holding the Down button until the table reaches the lowest position The control unit has now registered the lowest elevation and is ready to use Maintenance amp Repairs 2 1 Repairs Check all screws and bolts after first week of use and tighten screws and bolts where necessary to ensure safe operation of the table If the table cannot be raised or lowered check the cable connection between the handset unit and the motor units leg system as well as between the power unit and the mains outlet
6. ire electric shock or injury to persons Unplug from outlet before putting on or taking off parts Use this furnishing only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer Never operate this furnishing if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped in water Return the furnishing to a service center for examination or repair Keep the cord away from heated surfaces Never drop or insert any object into any opening Do not operate where aerosol spray products are being used or where oxygen is being administered Danger Always unplug this furnishing from the electrical outlet before cleaning Danger The table may only be operated while in an upright position and must under no circumstances be operated while upside down Warning The table must not be overloaded The maximum allowable load is 220165 100kg Danger The table is only to be used as a desk or work surface which allows the user stepless adjustment of the desktop between sitting and standing positions Danger The table must be operated in a dry enclosed space such as an office or similar never outdoors Danger Do not modify or make any changes to the control unit Important Information Danger Do not operate the control unit in a potentially explosive atmosphere Danger In the event of a fault motor or component whenever the desktop attempt
7. o use 11 5 4 Resetting After Replacing Control Unit If a control unit is replaced or switched the new control unit must first be reset to establish the lowest point of the table To do this press and hold the Up and Down buttons simultaneously for at least 7 seconds and then press Down to bring the table to the lowest point The control unit will now have registered the lowest point and the table is ready for use Verify correct functionality by elevating the table to the highest point and then back to the lowest point RESETTING AFTER REPLACING CON TROL UNIT The control unit is equipped with safety features the intermittency function and the overheating protection and memory function Intermittency function The intermittency factor of the control unit is 10 meaning it can be operated for 1 minute after which it must remain inactive for 9 minutes If the one minute limitation is exceeded the table will become inoperable until the control box resets automatically Overheating protection The table will become inoperable if the overheating protection is triggered and will return to operation automatically once the heat has dissipated sufficiently Memory function The control unit will retain information regarding the elevation of the table at all times This information will remain stored even in case of power failure or if the power cable is disconnected from the power outlet Soft start Pr
8. ogressive acceleration allows for soft starts and stops Speed the speed of the table varies with load 12 5 5 Installation Handset Unit Caution the power cord must be unplugged while the handset unit is being installed Mount the handset unit underneath the desktop using appropriate screws in the provided mounting holes 3 Screw Location Screw Location 1832 REV3 2 2014 13
9. or any missing components order Part 8655 Item Qty Description 11 4 End Cap Tube Replacement Pre Installed Components Part Description Part Description Q665 Replacement Leveling Glide yy 2509 Replacement Motor Assembly Instructions Base Top 4 2 Base Assembly 1 Place Actuator 1 upside down on clean surface assemble Foot 2 to bottom of actuator using 16mm screws 5 Qty 4 per foot CAUTION Do Not use 25mm screw 5 to attach foot this will cause damage to the internal components of the actuator 2 Loosen crossbar adjustment screws to allow crossbar sections to move freely 3 Place table top face down on a clean non abrasive surface Place both Actuators 1 and Crossbars 3 in approximate mounting locations Note Use Frame Alignment Holes and outer mounting holes in crossbar as a guide 4 Attach crossbars to actuator housing using 25mm screws 6 Qty 4 per bar Cap tube using End Cap 11 and Hole Plug 10 Refer to Detail 1 on Page 9 for reference 5 Adjust crossbar to required length by lining up crossbar mounting holes with frame alignment holes and fasten crossbars to top using 2 1 8 Wood Screws 7 6 Once base is fully attached crossbar sections can then be re tightened Caution Crossbar Cord Passage Hole must be centered in opening Refer to Detail 2 on page 9 7 Mount the Handset 4 in desired location wood screws supplied with switch Refer to Section 4 6 8 Pass motor cords
10. s to adjust the height it may move slightly before the safety cut out is triggered Please note there is a potential risk of pinching in this case Danger Intelligent system protection is not enabled during all resets Please note there is a potential risk of pinching in this case Danger This device is not intended for use by individuals with limited physical sensory or mental abilities or with lack of experience and or lack of expertise unless they are supervised by a person responsible for their safety or have received instructions from that person how to use the control unit Danger Children must be supervised at all times to ensure that they do not play with the control unit table Danger If the power cord is damaged it must be replaced by the manufacturer customer service or similar qualified person in order to prevent any risks Note Only clean the handset control unit with a dry or slightly moist cloth Before cleaning you must always unplug the power cord Danger The table may not be used to lift people Danger The table may not be structurally or technically altered or modified in any way During repair or maintenance work the power cable must be disconnected from the power outlet Danger The table is not to be used by persons including children with reduced physical sensory or mental capabilities or by individuals lacking the knowledge or experience to operate the table unless monitored or otherwise instructed re
11. set control unit under any circumstance There is danger of electric shock Caution The control unit is not designed for continuous operation Changing the desk position without interruption must not exceed the duty cycle indicated on the nameplate Caution Control unit may only be operated with mains voltage as specified on the label Caution Only use the power cord supplied with the control unit Check that is not damaged Never operate the control unit if the power cord is damaged Danger It is not allowed to connect self constructed products to handset motor controls To prevent damage of the unit use only components suitable for handset motor controls Danger Do not expose the control unit to moisture drips or splashes Caution Before connecting and disconnecting handset you must unplug the power cord Caution In the event of a malfunction i e the control unit keeps adjusting the desk because a movement button is jammed please unplug the unit immediately Danger When changing the desktop position there is a risk of pinching You must therefore ensure that no people or objects are located in the hazardous area or may reach into it Danger Risk of electrical shock Connect this furnishing to a properly grounded outlet only Caution To disconnect turn all controls to the off position then remove plug from outlet Danger Risk of injury Keep children away from foot support Danger To reduce the risk of burns f
12. te all cables so that they cannot be damaged by normal operation Please refer to the assembly instructions for this and use the supplied cable routing materials to secure the cables Connect the power cable to a power outlet and make sure that the cable is not in danger of being squeezed nicked twisted or otherwise damaged The table is now ready to use The motors will switch off automatically when the frame reaches its maximum or minimum elevations Assembly Instructions Base Top 4 1 Base and Hardware Components Note Please count and inspect all pieces before disposing of any carton or packing material Base Components For Base Models 80224MB and 80230MB When ordering components specific color and or size information may be required Please Contact a Mayline Customer Service Representative at 1 800 822 8037 Denotes Color Code B Black and S Silver Item Qty Description Part 1 2 Bifma Height Actuator Z507 2 2 Foot A8648 24 A8649 30 3 2 Adjustable Crossbar A8650 4 1 2 Button Handset 2508 Hardware Bag Screws For missing components order Part 8651 Item Qty Description 5 8 Screw M8x16mm Socket 6 12 Screw M8x25mm Cap 7 8 Screw 3 16 x 2 1 8 Wood 8 6 Cable Tie 9 1 Allen Wrench 8 SS Hardware Bag Hole Plugs For any missing components order Part No 8654 Item Qty Description 10 12 Hole Plug Adjustable Crossbar e Hardware Bag End Caps F
Download Pdf Manuals
Related Search