Home

Z40-B, Z40t-B, Z30-B, Z30t-B User`s Manual

1. Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC THE VC 1 AND MPEG 4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR I ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS VIDEO AND OR II DECODING AVC VC 1 AND MPEG 4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM OpenSSL Toolkit License Issues User s Manual LICENSE ISSUES The OpenSSL toolkit stays under a dual license i e both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit See below for the actual license texts Actually both licenses are BSD style Open Source licenses In case of any license issues related to OpenSSL please contact openssl core openssl org OpenSSL License Copyright c 1998 2011 The OpenSSL Project All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistribut
2. using is a generic term including compiling the project s source code as well as linking it to form a program or executable This program is referred to as a program using the FreeType engine This license applies to all files distributed in the original FreeType Project including all source code binaries and documentation unless otherwise stated in the file in its original unmodified form as distributed in the original archive If you are unsure whether or not a particular file is covered by this license you must contact us to verify this The FreeType Project is copyright C 1996 2000 by David Turner Robert Wilhelm and Werner Lemberg All rights reserved except as specified below 1 No Warranty THE FREETYPE PROJECT IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE OF THE FREETYPE PROJECT 2 Redistribution This license grants a worldwide royalty free perpetual and irrevocable right and license to use execute perform compile display copy create derivative works of distribute and sublicense the FreeType Project in both source and object code forms and derivative works thereof for any purpose and to authorize others to exercise some or all of the r
3. Battery Settings This utility can be used to specify the lower limit of remaining battery life for Sleep and Charge Move the slider bar to specify the lower limit If the remaining battery life falls below the setting the Sleep and Charge function will be stopped Clearing the Enable under Battery Mode check box sets the utility to only charge when the AC adaptor is connected TOSHIBA Password Utility T The TOSHIBA Password Utility provides two levels of password security User and Supervisor Passwords set by the TOSHIBA Password Utility function are different from the Windows password User s Manual User Password To start the utility click the following items Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Password Utility gt User Password User authentication might be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords etc E Set button Click this button to register a password After a password is set you are prompted to enter it when you start the computer 7 m After you set the password a dialog box appears asking whether you J want to save it to other media If you forget the password you can open the password file on another computer Be sure to keep the media in a safe place m When entering the character string to register the password enter from the keyboard character by character and do not enter as ASCII code or copy and
4. PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE The licence and distribution terms for any publically available version or derivative of this code cannot be changed i e this code cannot simply be copied and put under another distribution licence including the GNU Public Licence FreeType License Issues The FreeType Project LICENSE 2006 Jan 27 User s Manual 1 10 User s Manual Copyright 1996 2002 2006 by David Turner Robert Wilhelm and Werner Lemberg Introduction The FreeType Project is distributed in several archive packages some of them may contain in addition to the FreeType font engine various tools and contributions which rely on or relate to the FreeType Project This license applies to all files found in such packages and which do not fall under their own explicit license The license affects thus the FreeType font engine the test programs documentation and makefiles at the very least This license was inspired by the BSD Artistic and IJG Independent JPEG Group licenses which all encourage inclusion and use of free software in commercial and freeware products alike As a consequence its main points are that
5. Similar to left click Q Press and hold Press your finger down and leave it there for a few seconds This shows information to help you learn more about an item or opens a menu specific to what you are doing Similar to right click f Pinch or stretch Touch the screen or an item with two or more 4 fingers and then move the fingers toward each other pinch or away from each other stretch This visually zooms in or out your hand to rotate things in the direction you D gt Rotate Put two or more fingers on an item and then turn N turn your hand Only some items can be rotated av Slide Drag your finger on the touch screen to move through what is on the screen Using the Touch Pad The Touch Pad on the palm rest might support the following gestures User s Manual 4 1 Tap Simply tap your finger on the Touch Pad to act on items on the screen Similar to left click Pinch or stretch Place two or more fingers down on the Touch Pad and move them toward each other pinch or away from each other stretch This visually zooms in or out Two Finger Scroll Place two fingers down and slide them vertically or horizontally from anywhere on the Touch Pad This allows you to operate the scroll bars of a window 4 j Gg 7 Some of the Touch Pad operations described in this section are only J supported in certain applications The Keyboard The number of keys available on your keyboard depends on which country
6. It allows the angle of the display panel to be adjusted to provide optimum clarity Figure 2 5 Opening the display panel Z30 B 2 S 1 Display panel Product appearance depends on the model you purchased Open and close the display panel with reasonable care Opening it vigorously or slamming it shut might damage the computer User s Manual 2 5 T Be careful not to open the display panel too far as this might put stress on the display panel s hinges and cause damage Do not press or push on the display panel Do not lift the computer by the display panel Do not close the display panel with pens or any other objects left in between the display panel and the keyboard When opening or closing the display panel place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel Do not use excessive force when opening or closing the display panel Turning on the power This section describes how to turn on the power The Power indicator indicates the status Refer to the Power Condition Descriptions section for more information gt 1 2 User s Manual After you turn on the power for the first time do not turn it off until you have set up the operating system Volume cannot be adjusted during Windows Setup Do not touch the display screen while turning on the computer Open the display panel Press the power button Figure 2 6 Turning o
7. PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE This product includes cryptographic software written by Eric Young eay cryptsoft com This product includes software written by Tim Hudson tjh cryptsoft com Original SSLeay License Copyright C 1995 1998 Eric Young eay cryptsoft com All rights reserved This package is an SSL implementation written by Eric Young eay cryptsoft com The implementation was written so as to conform with Netscapes SSL This library is free for commercial and non commercial use as long as the following conditions are aheared to The following conditions apply to all code found in this distribution be it the RC4 RSA Ihash DES etc code not just the SSL code The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson tjh cryptsoft com Copyright remains Eric Young s and as such any Copyright notices in the code are not to be removed If this package is used in a product Eric Young should be given attribution as the author of the parts of the library used This can be in the form of a textual message at program startup or in docu
8. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions To avoid risk of lost data always make back up copies of data by periodically storing it on an external storage medium For optimum performance use your computer product only under recommended conditions Read additional restrictions in your product documentation Contact TOSHIBA technical service and support refer to TOSHIBA support section for more information 64 Bit Computing 64 bit processors are designed to take advantage of 32 and 64 bit computing 64 bit computing requires that the following hardware and software requirements are met 64 bit Operating System 64 bit CPU Chipset and BIOS Basic Input Output System 64 bit Device drivers 64 bit applications Certain 32 bit device drivers and or applications might not be compatible with a 64 bit CPU operating system and therefore might not function properly Memory Main System Part of the main system memory might be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities The amount of main system memory allocated to support graphics might vary depending on the graphics system applications utilized system memory size and other factors If your computer is configured with more than 3 GB memory the memory might be displayed as approxi
9. You can buy replacement AccuPoint caps from your TOSHIBA authorized dealer Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints By enrolling the ID and password onto the fingerprint authentication feature it is no longer necessary to input the password from the keyboard Fingerprint feature enables you to Logon to Windows and access a security enabled homepage through Internet Explorer Files and folders can be encrypted decrypted and third party access to them prevented Unlock the password protected screen saver Authentication of the User Password and if applicable the HDD SSD Password when booting up the computer Pre Boot authentication Single Sign On feature Fingerprint cannot be used in models that do not have a fingerprint module O T installed How to Swipe your Finger Using the following steps when swiping fingers for fingerprint registration or authentication can help to minimize authentication failures User s Manual Align the first joint of the finger to the center of the sensor Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible In performing this process you should also take care to ensure that the center of your fingerprint is on the sensor The following illustrations show the recommended way to swipe your finger over the fingerprint sensor Figure 4 3 Swipe the
10. antennas built in E Wireless LAN E Wireless LAN Bluetooth Legal Footnote Wireless LAN For more information regarding Wireless LAN refer to the Legal Footnotes section Microphone The built in microphone allows you to record sounds for your application Refer to the Sound System and Video mode section for more information 3 17 i Web Camera LED Web Camera The Web Camera LED glows when the Web Camera is operating Web Camera is a device that allows you to record video or take photographs with your computer You can use it for video chatting or video conferences using a communication tool Some models are equipped with a Web Camera Do not point the web camera directly at the sun Do not touch or press strongly on the web camera lens Failure to do so might reduce image quality Use an eyeglass cleaner cleaner cloth or other soft cloth to clean the lens if it becomes dirty Display screen Legal Footnote LCD 35 6 cm 14 0 LCD screen configured with the following resolutions E amp E FHD 1920 horizontal x 1080 vertical pixels Be aware that when the computer is operating on the AC adaptor the image displayed on the internal screen is somewhat brighter than when it operates on battery power This difference in brightness levels is intended to save power when operating on batteries For more information regarding LCD refer to the Legal Footnotes section Display hinges Keyboard Power b
11. eco DC IN 19V Homi User s Manual Figure 3 2 The left side of the computer Z30 B 1 DC IN 19V jack 4 Universal Serial Bus USB 3 0 port 2 External RGB monitor port 5 Headphone Microphone jack 3 HDMI out port 6 Smart Card slot Provided with some models Product appearance depends on the model you purchased DC IN 19V jack External RGB monitor port HDMI out port Universal Serial Bus USB 3 0 port The AC adaptor connects to this jack to power the computer and charge its internal batteries Note that you must only use the model of AC adaptor supplied with the computer at the time of purchase Using the wrong AC adaptor can damage the computer This port provides 15 pin analog RGB port Refer to the External RGB monitor port pin assignment section for information on external RGB monitor port pin assignment This port allows you to connect an external RGB monitor to the computer HDMI out port can connect with Type A connector HDMI cable One Universal Serial Bus port which complies to the USB 3 0 standard is provided on the left side of the computer The USB 3 0 port is compliant with USB 3 0 standard and backward compatible with USB 2 0 devices USB 3 0 port s might work as USB 2 0 port s when operating in USB Legacy Emulation mode Note that it is not possible to confirm the operation of all functions of all USB devices that are available S
12. informing you of significant system conditions This application recognizes the system and individual component serial numbers and tracks specific activities related to their usage To access this utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Health Monitor For details on TOSHIBA PC Health Monitor see the help file The TPM Trusted Platform Module is a security encryption device for the internal storage drive Trusted Platform Module is provided with some models To operate the TPM function use an applicable utility 9 You might not have all the software listed above depending on the model T you purchased To access the setup files of the drivers utilities click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Applications and Drivers Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use Access each function using the following procedures 1 To access the Power Options click Start gt Control Panel gt System and Security gt Power Options User s Manual User s Manual Display automatic power off Internal storage drive automatic power off System automatic Sleep Hibernation Mode 1 Power on password Intelligent power supply Battery save mode Panel power on off 1 Low battery automatic Hibernatio
13. 24 Figure 4 11 Connecting the RGB cable to the External RGB monitor port Z30 B 1 External RGB monitor port 2 RGB cable Product appearance depends on the model you purchased When you turn on the power the computer automatically recognizes the monitor and determines whether it is a color or monochrome device When displaying desktop on an external RGB monitor desktop is sometimes displayed on the center of the monitor with black bars around desktop with small size At that time read the manual of the monitor and set the display mode which is supporting at the monitor Then it will be displayed with suitable size with correct aspect ratio The HDMI out port Some models are equipped with an HDMI out port HDMI High Definition Multimedia Interface port digitally transfers both video and audio data without reducing the quality HDMI compatible external display devices including televisions can be connected via the HDMI out port To connect an HDMI compatible display device do the following 7 To connect a device to the HDMI out port you must purchase a suitable J HDMI cable 1 Plug one end of the HDMI cable into the HDMI in port of the HDMI display device 2 Plug the other end of the HDMI cable into the HDMI out port on your computer 3 Turn the HDMI display device s power on User s Manual 4 25 Figure 4 12 Connecting the HDMI out port Z30 B 1 HDMI out port 2 HDMI cable Product appearance depends
14. Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer Use of an incompatible AC adaptor might cause fire or damage to the computer possibly resulting in serious injury TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor Never plug the AC adaptor into a power source that does not correspond to both the voltage range and the frequency specified on the regulatory label of the unit Failure to do so might result in a fire or electric shock possibly resulting in serious injury Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use Failure to do so might result in a fire or electric shock possibly resulting in serious injury The supplied power cord conforms to safety rules and regulations in the region the computer is bought and should not be used outside this region For use in other regions buy power cords that conform to safety rules and regulations in the particular region T User s Manual E Do not use a 3 pin to 2 pin conversion plug m When you connect the AC adaptor to the computer always follow the steps in the exact order as described in this User s Manual Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug might hold an electric
15. Hardware and Sound gt Mouse If you are still unable to resolve the problem contact TOSHIBA Support USB mouse Problem On screen pointer does not respond to mouse operation Double clicking does not work The on screen pointer moves too fast or too slow The on screen pointer moves erratically USB device Procedure In this instance the system might be busy Try moving the mouse again after waiting a short while Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure that it is firmly attached In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK The elements of the mouse responsible for detecting movement might be dirty Refer to the documentation supplied with the mouse for instructions on how to clean it If you are still unable to resolve the problem contact
16. RGB monitor port Headphone Microphone jack m When you use external display ports on the Port Replicator or on your computer some software might show different type of ports which you connected m When connecting an AC Adaptor to the Port Replicator use only the AC Adaptor included with Port Replicator Do not use the computer s AC Adaptor Refer to the Port Replicator s User s Manual for more details To dock your computer in the Port Replicator do the following 4 27 T User s Manual Align the top left and top right corner of your computer to the correct mark on the Port Replicator Short Name Top Left Corner Top Right Corner Z30 B A AB Z40 B B AB Press down on the back of the computer until it clicks into place The computer connector on the port replicator engages the computer s docking port When the computer is connected the Docked light on the Port Replicator glows green while the computer is powered on Figure 4 13 Aligning your computer with the Port Replicator Z30 B 1 Docking port computer Product appearance depends on the model you purchased Make sure the AC adaptor is always connected to the TOSHIBA Hi Speed Port Replicator IlI 180W 120W while in use Otherwise the Port Replicator will stop working possibly resulting in data loss Some models support multiple display function if equipped with a TOSHIBA Hi Speed Port Replicator III 180W 120W The port replicator suppo
17. Solid State Drive Thin film Transistor Uniform Resource Locator Universal Serial Bus Wide Area Network Wide Quad High Definition World Wide Web 7 22 Index User s Manual AC adaptor additional 4 29 connecting 2 3 DC IN 19V jack 3 3 3 15 Battery extending life 4 15 monitoring capacity 4 14 save mode 5 4 types 4 12 Bluetooth Bluetooth Stack for Windows by Toshiba 5 2 Cleaning the computer 1 16 Cooling vents 3 6 3 12 3 16 DC IN Battery indicator Display automatic power off 5 4 hinges 3 9 3 18 opening 2 5 screen 3 9 3 18 Documentation list 2 1 Dual Pointing Device AccuPoint 4 5 Touch Pad 6 8 Equipment checklist 2 1 External monitor problems 6 12 Graphics Processing Unit 3 21 HW Setup accessing window Keyboard Function keys F1 F12 4 3 problems 6 6 Windows special keys 4 5 LAN cable types 4 18 connecting 4 19 Media care Card care 4 21 Index 1 User s Manual Memory card care 4 21 memory media card inserting 4 22 removing 4 22 Memory media slot 4 19 Moving the computer 1 16 Password power on 5 4 Starting the computer by password 5 9 Supervisor 5 9 user 5 8 Pointing Device Touch Pad 3 10 3 19 Power conditions 3 23 Hibernation Mode 2 10 panel on off 5 4 Shut Down mode 2 7 Sleep Mode 2 8 turning off 2 7 turning on 2 6 Problems AC power 6 4 Analyzing the problem 6 2 Battery 6 5 Dual Pointing device 6 7 Hardware and system checklist 6 4 H
18. and distribution on a network without the permission of the copyright owner is a violation of copyright or author s rights and is subject to civil damages or criminal action Comply with copyright laws in making any reproduction from this manual Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for your computer at the time of this manual s production However succeeding computers and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the computer and the manual Trademarks Intel is a trademark or registered trademark of Intel Corporation Windows Microsoft and Windows logo are registered trademarks of Microsoft Corporation User s Manual 1 1 The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Toshiba Corporation and its affiliates is under license The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries DTS the Symbol amp DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS Inc DTS Inc All Rights Reserved Secure Digital and SD are trademarks of SD Card Association MultiMediaCard and MM
19. applications Intel AMT allows IT to better discover heal and protect their networked computing assets Consult with your system administrator about configurations of the AMT function before connecting to a network Disable the AMT function User s Manual Intel AMT function is enabled by default and in a situation where no system administrator presents it is strongly recommended that you turn off the AMT function before connecting to a network If the AMT function is NOT turned off there is a danger that the management of AMT function will be abused by other parties which possibly lead to the leak of sensitive and or proprietary information data loss HDD SSD erasure or file overwritten First you must do the following in the BIOS setup utility 1 Turn on the computer while pressing the F2 key i User s Manual 2 3 On the BIOS setup utility screen change AMT Setup Prompt to Enabled Press the F10 key and press Y key to save the settings When the computer restarts the message Press lt Ctrl P gt to enter Intel R ME Setup appears Press CTRL P to enter the MEBx Setup To disable the AMT function do the following 1 2 Select MEBx Login and enter the default password admin in the password field Enter a new password Password must comply with the following requirements concerning character types and length Must be between 8 and 32 characters long Must contain at least one n
20. cleaner and always ensure that you let the display panel dry properly before closing it HDD Problem Slow performance Memory Media Card Procedure The files on the HDD might be fragmented In this instance you should run the disk defragmentation utility to check the condition of your files and the HDD Refer to the operating system s documentation or online Help File for further information on operating and using the defragmentation utility As a last resort you should reformat the HDD and then reload the operating system and all other files and data If you are still unable to resolve the problem contact TOSHIBA Support For further information refer to Operating Basics Problem Memory media card error occurs You cannot write to a memory media card You cannot read a file Pointing device Procedure Remove the memory media card from the computer and then reinsert it in order to ensure that it is firmly connected If the problem persists then you should refer to the documentation supplied with your memory media card for further information Remove the memory media card from the computer and check to ensure that it is not write protected Check to ensure the required file is actually on the memory media card that is inserted into the computer If you are still unable to resolve the problem contact TOSHIBA Support If you are using a USB mouse you should also refer to both the USB mouse sec
21. default by first clicking Default button and then Apply button 3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer When HDD Protection detects computer vibration the HDD head is parked and the 3D object disk rotation stops When the head is un parked the disk begins to rotate again Click 3D Viewer button to start E This 3D object virtually represents the computer s internal HDD This representation might vary from the actual number of disks disk rotation head movement part size shape and direction E This feature might use a large amount of CPU and memory on some models The computer might become slow or sluggish when attempting to run other applications while the 3D Viewer is displayed m Intensely shaking the computer or other subjecting it to strong impacts might damage the computer TOSHIBA Setup Utility User s Manual TOSHIBA Setup Utility is a BIOS setup utility that provides you a menu based user interface so that you can easily view and change BIOS settings To enter the BIOS setup utility do the following 1 Save your work 2 Click Start Point to the arrow i beside the Shut down button and then select Restart 3 Hold down the F2 key and then release this key one second after the computer is power on To save the changes and exit the utility press the F10 key and proceed by selecting Yes or select Exit gt Exit Saving C
22. drive indicator 2 DC IN Battery indicator 5 Wireless communication indicator 3 Power indicator 6 Wireless WAN WiMAX indicator Provided with some models Product appearance depends on the model you purchased Stereo speakers The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system ai DC IN Battery The DC IN Battery indicator shows the indicator condition of the DC IN and the battery charge status White indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor Refer to the Power Condition Descriptions section for more information on this feature Power indicator The Power indicator normally glows white when the computer is turned on However if you turn off the computer into Sleep Mode this indicator flashes amber User s Manual 3 11 CS Internal storage drive The Internal storage drive indicator blinks indicator white whenever the computer is accessing the internal storage drive p Wireless The Wireless communication indicator glows communication amber when the Wireless functions are turned indicator on Some models are equipped with Wireless functions Y Wireless WAN WiMAX The Wireless WAN WiMAX indicator glows indicator blue when the Wireless WAN WiMAX functions are turned on For some models the indicator glows and blinks to indicate the connection status of the Wirele
23. exit the failed program without shutting down the operating system or closing other programs To close a program that has stopped responding 1 Press CTRL ALT and DEL simultaneously once then click Start Task Manager The Windows Task Manager window appears 2 Click the Applications tab If a program has stopped responding the words not responding appear beside its name in the list 3 Select the program you want to close then click End Task Closing the failed program should allow you to continue working If it does not continue with the next step 4 Close the remaining programs one by one by selecting the program name then End Task Closing all programs should allow you to continue working If it does not power off your computer and then restart it The computer does not start Make sure that you attached the AC adaptor and power cord cable properly If you are using the AC adaptor check that the wall outlet is working by plugging in another device such as a lamp Verify that the computer is on by looking at the Power indicator If the indicator is glowing the computer is on Also try turning the computer off and then on If you are using an AC adaptor verify that the computer is receiving power from the external power source by looking at the DC IN Battery indicator If the indicator is glowing the computer is connected to a live external power source Hardware and system checklist This section discuss
24. faster Analyzing the problem User s Manual Sometimes the computer gives you clues that can help you identify why it is malfunctioning In view of this keep the following questions in mind m Which part of the computer is not operating properly keyboard internal storage drive display panel Touch Pad Touch Pad control buttons as each device produces different symptoms Check the options within the operating system to ensure that its configuration is set properly What appears on the display Does it display any messages or random characters Make a screenshot of the current display and if possible look up the messages in the documentation included with the computer software or operating system m Check that all connecting cables are correctly and firmly attached as loose cables can cause erroneous or intermittent signals E Do any indicators light if so which ones what color are they and do they stay on or blink Write down what you see m Do you hear any beeps if so how many are they long or short and are they high pitched or low pitched In addition is the computer making any unusual noises Write down what you hear Record your observations so you can describe them in detail to TOSHIBA Support Software The problems might be caused by your software or disk If you cannot load a software package the media might be damaged or the program might be corrupted In these instances try loading another copy of th
25. finger 1 Sensor amp Avoid swiping with your finger stiff or pressed too hard onto the sensor and take care to ensure that the center of the fingerprint is touching the sensor before swiping Either of these conditions might cause fingerprint reading to fail amp Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor m There is a possibility of authentication failures if the finger is swiped too quickly or too slowly Follow any on screen instructions to adjust the speed used during the swipe process Points to note about the Fingerprint Sensor Be aware of the following considerations when using the fingerprint sensor A failure to follow these guidelines might result in damage to the sensor sensor failure fingerprint recognition problems or a lower fingerprint recognition success rate Do not scratch or poke the sensor with your nails or any hard or sharp objects Do not press the sensor strongly Do not touch the sensor with a wet finger or any wet objects Keep the sensor surface dry and free from water vapor E Do not touch the sensor with a soiled or dirty finger as minute foreign particles of dust and dirt might scratch it E Do not paste stickers or write on the sensor E Do not touch the sensor with a finger or any other object which might have a build up of static electricity on it User s Manual Observe the following before yo
26. general population consult Safety Code 6 obtainable from Health Canada s website www hc sc gc ca Caution Exposure to Radio Frequency Radiation The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits Nevertheless the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized In the usual operating configuration the distance between the antenna and the user should not be less than 20cm Please refer to the computer user s manual for the details regarding antenna location The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population consult Safety Code 6 obtainable from Health Canada s website www hc sc gc ca Caution Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5 15 to 5 25GHz frequency range High power radars are allocated as primary users i e priority users of the bands 5 25 to 5 35GHz and 5 65 to 5 85GHz and that these radars could cause interference and or damage to LE LAN devices Taiwan Article 12 Without permission granted by the NCC any company enterprise or user is not allowed to change frequency enhance transmitting power or alter original characteristic as well as performance to an approved low power radio freq
27. hardware or software vendor before using or configuring a network connection Memory media A User s Manual The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices such as digital cameras and Personal Digital Assistants Keep foreign objects out of the memory media slot Never allow metal objects such as screws staples and paper clips to enter the computer or Keyboard Foreign metal objects can create a short circuit which can cause computer damage and fire possibly resulting in serious injury 2 E An adaptor is required to use miniSD microSD Card 1 E Not all memory media have been tested and verified to work correctly Therefore it is not possible to guarantee that all memory media can operate properly Figure 4 9 Examples of memory media Secure Digital SD Card microSD card adaptor and microSD card MultiMediaCard MMC Points to note about the memory media card SD SDHC SDXC memory cards comply with SDMI Secure Digital Music Initiative which is a technology adopted to prevent unlawful copy or playback of digital music For this reason you cannot copy or play back protected material on another computer or other device and you cannot reproduce any copyrighted material except for your personal enjoyment The following is a simple explanation for distinguishing SD memory cards from SDHC me
28. in this manual to bring important information to your attention Each type of message is identified as follows Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions User s Manual T User s Manual A caution informs you that improper use of equipment or failure to follow instructions might cause data loss equipment damage or might result in minor or moderate injury Please read A note is a hint or advice that helps you make best use of your equipment Chapter 2 Getting Started This chapter provides an equipment checklist and basic information to start using your computer If you use an operating system that was not pre installed by TOSHIBA some of the features described in this manual might not function properly Equipment checklist Carefully unpack your computer taking care to save the box and packaging materials for future use Hardware Check to make sure that you have all the following items m TOSHIBA Portable Personal Computer AC adaptor and power cord 2 pin plug or 3 pin plug H Cleaning cloth provided with some models Documentation User Information Guide E Instruction Manual for Safety and Comfort If any of the items are missing or damaged contact your dealer immediately Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Start The wo
29. is noted that an often used older battery will not operate for as long as a new battery even when both are fully charged Maximizing battery operating time The usefulness of a battery depends on how long it can supply power on a single charge while how long the charge lasts in a battery depends on Processor speed Screen brightness User s Manual 4 14 System Sleep Mode System Hibernation Mode Display power off period Internal storage drive power off period How often and for how long you use the internal storage drive and external disk drives for example optical disc How much charge the battery contained to begin with How you use optional devices such as a USB device to which the battery supplies power Where you store your programs and data Whether you close the display panel when you are not using the keyboard closing the display saves power The environmental temperature operating time decreases at low temperatures System Sleep Mode System Hibernation Mode Display power off period Whether you enable Sleep Mode which can conserve battery power if you are frequently turning the computer off and on Whether you enable Sleep and Charge function Batteries exhausted time Refer to User Information Guide about batteries exhausted time Extending battery life User s Manual To maximize the life of your battery packs do the following at least once a month 1 2 3 Turn off the computer s po
30. it is not set for the internal display only Check to see if the external monitor is connected When the external monitor is set as the primary display device in extended desktop mode it does not display when the computer wakes up from Sleep Mode if the external monitor has been disconnected while in Sleep Mode To keep this from happening do not disconnect the external monitor while the computer is in Sleep or Hibernation Mode Remember to turn off the computer before disconnecting the external monitor When the display panel and an external monitor are set to clone mode and they are turned off by the timer the display panel or the external monitor might not display when turned on again If this occurs press the function key to reset the display panel and external monitor to clone mode Check that the cable connecting the external monitor to the computer is firmly attached If you are still unable to resolve the problem contact TOSHIBA Support Procedure Check for a firm cable connection between the LAN jack and the LAN hub Problem Wake up on LAN does not work Wireless LAN Problem Cannot access Wireless LAN Bluetooth Problem Cannot access Bluetooth device TOSHIBA support Procedure Make sure that the AC adaptor is connected The Wake up on LAN function consumes power even when the system is off If problems persist consult your LAN administrator Procedure Make sure that the wire
31. metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury User s Manual 3 4 zia A MOC User s Manual SIM Card slot Universal Serial Bus USB 3 0 port This slot allows you insert a SIM card which enables a high speed access to the Internet corporate Intranet and your email while you are away from office Refer to the Wireless WAN device section for more information Two Universal Serial Bus ports which comply to the USB 3 0 standard are provided on the right side of the computer The USB 3 0 port is compliant with USB 3 0 standard and backward compatible with USB 2 0 devices USB 3 0 port s might work as USB 2 0 port s when operating in USB Legacy Emulation mode Note that it is not possible to confirm the operation of all functions of all USB devices that are available Some functions associated with a specific device might not operate properly Before removing a USB device from the USB port of your computer click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and then select the USB device that you want to remove Keep foreign metal objects such as screws staples and paper clips out of the USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury LAN jack This jack lets you connect to a LAN The adaptor has built in support for Ethernet L
32. of fingerprint succeeds Enrollment succeeded Do you want to save this fingerprint message box appears Click OK 7 The following message appears It s strongly recommended you enroll one more fingerprint Click OK and repeat Step 3 4 5 and 6 with another finger Ga It is strongly recommended that you register 2 or more fingerprints You cannot enroll the same fingerprint more than once even on a different user account Delete the Fingerprint Data Saved fingerprint data is stored in special non volatile memory inside the fingerprint sensor Therefore if you give the computer to someone else or dispose of it in any way please uninstall the application or delete all the logs created by the application Delete the fingerprint data for the currently logged in user 1 2 In the TOSHIBA Fingerprint Utility main menu select Fingerprint Enroll In the Fingerprint Enroll window it enables you to delete the fingerprint data for the currently logged in user Click an enrolled finger you want to delete Do you want to delete message box appears on the screen and then click OK If you want to delete other fingerprints repeat this step If only one fingerprint is registered the message At least one fingerprint is required appears after clicking OK You are not allowed to delete a unique fingerprint Click Close Do you want to quit is displayed Click OK It will be returned to the TOSHIBA Fingerprint Utility
33. paste the character string In addition ensure that the registered password is correct by outputting the character string to the password file m When entering a password do not enter any characters for example I or produced by pressing the SHIFT or ALT keys H Delete button Click this button to delete a registered password Before you can delete a password you must first enter the current password correctly m Change button Click this button to change a registered password Before you can change a password you must first enter the current password correctly E Owner String text box You can use this box to associate text with the password After you enter text click Apply or OK When the computer is started this text is displayed together with the prompt asking you to enter a password y You can launch the BIOS setup utility to set change or delete the HDD J SSD Password or HDD SSD Master Password Refer to TOSHIBA Setup Utility section for further information User s Manual 5 8 E f you forget your HDD SSD User Password TOSHIBA will NOT be able to assist you and your internal storage drive will be rendered COMPLETELY and PERMANENTLY INOPERABLE TOSHIBA will NOT be held responsible for any loss of any data any loss of use or access to your internal storage drive or for any other losses to you or any other person or organization that result from the loss of access to your internal storage drive If you cannot ac
34. programmes available in your country please visit our website www toshiba eu recycling or contact your local council office or the retail outlet where you purchased the product These symbols might not stick depending on the country and region where you purchased REACH Compliance Statement User s Manual The European Union EU chemical regulation REACH Registration Evaluation Authorization and Restriction of Chemicals entered into force on 1 June 2007 with phased deadlines to 2018 Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation Please consult the following website www toshiba eu reach for information about the presence in our articles of substances included on the candidate list according to REACH ina concentration above 0 1 weight by weight Following information is only for Turkey Disposal of products The crossed wheelie bin symbol means that this ps product should not be collected and disposed with other household wastes When product become waste at the end of life to protect environment and human health it should be given to nearest collection recycling or disposal center For more information about collection and recycling programs in your country please contact your local authority or the retailer where the product was purchase
35. systems possibly causing serious injury Before entering Sleep Mode be sure to save your data E 7o prevent data loss do not switch to Sleep Mode while transferring data to external media such as USB devices memory media or other external memory devices m When the AC adaptor is connected the computer will go into Sleep Mode according to the settings in the Power Options to access it click Start gt Control Panel gt System and Security gt Power Options i User s Manual To restore the operation of the computer from Sleep Mode press and hold the power button or any key on the keyboard for a short amount of time Note that keyboard keys can only be used if the Wake up on Keyboard option is enabled within the TOSHIBA HWSetup If the computer enters Sleep Mode while a network application is active the application might not be restored when the computer is next turned on and the system returns from Sleep Mode To prevent the computer from automatically entering Sleep Mode disable Sleep Mode within the Power Options To use the Hybrid Sleep function configure it in the Power Options Benefits of Sleep Mode The Sleep Mode feature provides the following benefits Restores the previous working environment more rapidly than the Hibernation Mode feature Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature Allows
36. the computer Disconnect the AC adaptor for several seconds and reconnect the AC adaptor If it still does not operate properly you should contact your reseller or dealer No light Under any other conditions the indicator does not light If the battery pack becomes too hot while it is being charged the charge stops and the DC IN Battery indicator goes out When the temperature of the battery pack falls to a normal range charging will resume This process occurs regardless of whether the computer s power is on or off Power indicator User s Manual Check the Power indicator to determine the power status of the computer The following indicator conditions should be noted White Indicates that power is being supplied to the computer and the computer is turned on Flashing Amber Indicates that the computer is in Sleep Mode and that there is sufficient power available AC adaptor or battery to maintain this condition No light Under any other conditions the indicator does not light 3 23 Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that must be taken when using it Using the Touch Screen Some models are equipped with a touch screen You can use your finger to manipulate icons buttons menu items the on screen keyboard and other items on the touch screen Tap Simply tap your finger on the touch screen to act on items on the screen
37. the computer ON to charge the device m When Sleep and Charge function is enabled USB bus power DC5V is be supplied to compatible ports even when the power of the computer is turned OFF USB bus power DC5V is similarly supplied to the external devices which are connected to the compatible ports However some external devices cannot be charged solely by supplying USB bus power DC5V As for the specifications of the external devices contact the device manufacturer or check the specifications of the external devices thoroughly before use m Using the sleep and charge function to charge external devices takes longer than charging the devices with their own chargers m If Sleep and Charge function is enabled the computer s battery will discharge during hibernation or when the computer is turned off It is recommended that you connect the AC adaptor to the computer while using Sleep and Charge function m External devices connected to the USB bus power DC5V function that interfaces with the power ON OFF of the computer might always be in an operational state When there is a current overflow of the external devices connected to the compatible ports USB bus power DC5V supply might be stopped for safety reasons m When Sleep and Charge function is enabled the USB Wakeup function might not work for compatible ports In that case if there is a USB port that does not have the Sleep and Charge function attach the mouse or keybo
38. to the use of wireless communication equipment Radio Frequency E Band 5 GHz 5150 5850 MHz Revision a and n E Band 2 4 GHz 2400 2483 5 MHz Revision b g and n The range of the wireless signal is related to the transmit rate of the wireless communication Communications at lower transmit range might travel larger distances H The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high density materials H Range is also impacted due to obstacles in the signal path of the radio that might either absorb or reflect the radio signal Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5 15 to 5 25GHz frequency range High power radars are allocated as primary users i e priority users of the bands 5 25 to 5 35GHz and 5 65 to 5 85GHz and that these radars could cause interference and or damage to LE LAN devices Bluetooth wireless technology User s Manual Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers printers and mobile phones When it is enabled Bluetooth provides the wireless personal area network environment which is safe and trustworthy that is quick and easy You cannot use the built in Bluetooth functions of the computer and an external Bluetooth adaptor simultaneously For reference Bluetoot
39. AC power mode TOSHIBA recommends that you leave this and other energy saving features active so that your computer will operate at its maximum energy efficiency You can wake the computer from Sleep Mode by pressing the power button Your ENERGY STAR certified computer should be set by default to enter a low power sleep mode after a period of inactivity Simply touching the mouse or keyboard wakes the computer in seconds These sleep features can save you up to 23 per year 200 kWh per year in electricity and prevent up to 300 pounds of greenhouse gas emissions annually To learn how to adjust or activate these sleep settings on your computer please go to www energystar gov sleepinstructions To activate sleep settings organization wide quickly and easily through network tools please go to www energystar gov powermanagement Disposing of the computer and the computer s battery The computer s battery pack is not user accessible Contact an authorized TOSHIBA service provider for details regarding how to dispose of the computer and the battery pack General Precautions TOSHIBA computers are designed to optimize safety minimize strain and withstand the rigors of portability However certain precautions should be User s Manual observed to further reduce the risk of personal injury or damage to the computer Be certain to read the following general precautions and to note the cautions included in the text of the ma
40. AN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Refer to Operating Basics for details Do not connect any cable other than a LAN cable to the LAN jack It might cause damage or malfunction Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer Back Z30 B The following figure shows the back of the computer Figure 3 4 The back of the computer Z30 B 1 Cooling vents Product appearance depends on the model you purchased Cooling vents The cooling vents help the processor to avoid overheating AN Do not block the cooling vents Keep foreign metal objects such as screws staples and paper clips out of the cooling vents Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Carefully clean the dust on the cooling vents surface using a soft cloth Underside Z30 B The following figures show the underside of the computer Ensure that the display is closed before the computer is turned over to avoid causing any damage Figure 3 5 The underside of the computer Z30 B aie es lt 2 j 1 Cooling vents 2 Docking port Provided with some models Product appearance depends on the model you purchase
41. C are trademarks of MultiMediaCard Association Realtek is a registered trademark of Realtek Semiconductor Corporation All other product names and service names in this manual might be trademarks or registered trademarks of their respective companies Regulatory Information i FCC User s Manual The regulatory information herein might vary Check the ID information on the bottom of the device for specific information applicable to the model you purchased information FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna E Increase the separation between the equipment and receiver E Connect the equipment into a
42. Check with your LAN administrator regarding set up procedures If you are using Gigabit Ethernet LAN 1000 megabits per second 1000BASE T be sure to connect with a CAT5e cable or higher You cannot use a CAT3 or CAT5 cable If you are using Fast Ethernet LAN 100 megabits per second 100BASE TX be sure to connect with a CAT5 cable or higher You cannot use a CAT3 cable If you are using Ethernet LAN 10 megabits per second 10BASE T you can connect with a CAT3 or higher cable Connecting the LAN cable A To connect the LAN cable do the following Connect the AC adaptor before connecting the LAN cable The AC adaptor must remain connected during LAN use If you disconnect the AC Adaptor while the computer is accessing a LAN the system might hang up E Do not connect any other cable to the LAN jack except the LAN cable Otherwise malfunctions or damage might occur Do not connect any power supplying device to the LAN cable that is connected to the LAN jack Otherwise malfunctions or damage might occur 1 Turn off the power to all external devices connected to the computer 2 Plug one end of the cable into the LAN jack Press gently until you hear the latch click into place Figure 4 8 Connecting the LAN cable Z30 B 1 LAN jack 2 LAN cable Product appearance depends on the model you purchased 3 Plug the other end of the cable into a LAN hub connector or router Check with your LAN administrator and
43. DD 6 7 Internal display panel 6 6 Keyboard 6 6 Memory Media Card 6 7 Overheating power down 6 4 Power 6 4 Real Time Clock 6 6 Sound system 6 11 TOSHIBA support 6 13 Touch Pad 6 8 USB device 6 9 USB mouse 6 9 Recovery Media 5 16 Recovery Partition 5 17 Restarting the computer 2 8 SD SDHC SDXC Card formatting 4 21 note 4 20 Security lock 4 29 SIM card installing 4 16 removing 4 17 Sleep Mode setting 2 8 System automatic 5 4 Smart Card inserting 4 23 removing 4 24 Sound system problems 6 11 SSD automatic power off 5 4 Index 2 User s Manual TOSHIBA HDD SSD Alert Utility 5 2 TOSHIBA PC Diagnostic Tool 5 1 Touch Pad 3 10 3 19 4 1 6 8 Touch Screen 4 1 USB device problems 6 9 Video mode 4 32 Video RAM 3 21 Web Camera 3 9 3 18 Wireless communication 7 5 Index 3
44. E HDD Protection function does not guarantee that the HDD will not be damaged BH During audio video playback when the computer detects a shock or vibration and the HDD s head is parked the playback might be temporarily interrupted E HDD Protection cannot be used in models that are equipped with SSD When vibration is detected a notification is displayed on the screen and the icon in the Taskbar changes to the protection state This message is displayed until the OK button is pressed or 30 seconds pass When vibration subsides the icon returns to the normal state Setting up HDD Protection User s Manual You can change HDD Protection settings To open the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HDD Protection The utility can also be started from the icon in the Taskbar or from the Control Panel a p A User s Manual HDD Protection You can enable or disable HDD Protection by moving the slider to the right or left HDD Protection does not work when the computer is booting in Sleep Mode in Hibernation Mode in transition to Hibernation Mode recovering from Hibernation Mode or powered off Do not subject the computer to vibration or impact while the protection is disabled HDD Protection Message Move the slider to the right to enable notification when viberation is detected System Tray Icon Move the slider to the right to show HDD Protection icon in the Taskb
45. Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m To remain in conformance with European spectrum usage laws for Wireless LAN operation the above 2 4GHz and 5GHz channel limitations apply for outdoor usage The user should use the wireless LAN utility to User s Manual 7 10 User s Manual check the current channel of operation If operation is occurring outside of the allowable frequencies for outdoor use as listed above the user must contact the applicable national spectrum regulator to request a license for outdoor operation Canada Industry Canada IC This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage regu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable Les dispositifs fonctionnant dans la bande 5 15 5 25GHz sont r serv s uniquement pour une utilisation a l int rieur afin de r duire le
46. R Adjust the timer under Backlight Lighting Time This function is supported with some models Flash Cards Flash Cards makes it visual and easy to access and use the function keys Normally the cards are hidden from view To activate and use the Flash Cards do the following 1 Press and hold the FN key Flash Cards appears on top of the screen by default 2 Press the function key or click the card associated with the desired function The selected card with available options appears 3 Press the function key repeatedly to cycle through the available options and release the FN key when the desired option is selected You can also click the desired option For more information refer to the TOSHIBA Flash Cards Help file To access this help click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Flash Cards In the Settings for Flash Cards window click the Help button Sticky key You can use the TOSHIBA Accessibility utility to make the FN key sticky that is you can press it once release it and then press a desired function key To start the TOSHIBA Accessibility utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Accessibility Windows special keys The keyboard provides two keys that have special functions in Windows the Windows logo key activates the Start menu while the application key has the same function as the secondary right mouse button This
47. Sign On feature User s Manual Overview about Fingerprint Pre Boot authentication The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up If you do not want to use the fingerprint authentication system for password authentication when booting up but prefer to use the keyboard based system instead follow the on screen instructions when the Fingerprint System Authentication screen is displayed This will switch the password input screen across to the keyboard based one E You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Pre Boot authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on H When swiping your finger ensure that you do it slowly and at a constant speed If you find that this does not improve the authentication rate you should try to adjust the speed at which the finger is swiped E f there are any changes in the environment or settings related to authorization you will be required to provide authorization information such as a User Password and if applicable the HDD SSD Password Overview about Fingerprint Single Sign On feature This is a feature that allows the user to complete the authentication for both the User BIOS Password and if applicable the HDD SSD Password and logging onto Windows using only one fi
48. TOSHIBA Leading Innovation gt gt gt User s Manual TECRA Z40 B Z40t B PORTEGE Z30 B Z30t B Satellite Z30 B Z30t B Z40 B Z40t B Series Table of Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 User s Manual TOSHIBA Legal Regulatory and Safety Copyright Disclaimer and Trademarks 2 ccceseeeseeeeeeeeeeeeeeeeees 1 1 Regulatory Information c ccicccsceceterceceetcecstececestectceteseedteestecendteccteessesees 1 2 Video Standard Notice cccecccceceseeeeeeeeeeeeeneeeeeeeeeeeeeeeeeeseeeeeeeeeeeeees 1 8 OpenSSL Toolkit License Issues 2 cceceeeeeceeeeeeeeeeeeeeeeeeneeeeeeeeee 1 8 FreeType License ISSUES ccceeeeeeseeee ee eeeeeeeceeseseeaeeeeeeseeeeneeeeees 1 10 ENERGY STAR Program cccceeeecessneeeeseeeeseeeeeeeneeeesenseseseesesseneeenees 1 14 Disposing of the computer and the computer s battery 1 14 General Precautions cccececeeecceeeeeeeeeeeeeeeeeeaeeeeeeseneneeeeseeeeseeeeeees 1 14 Safety ICONS cceeececeseeeeeeeeeeeeeeeseeeeeeseeeeeeseeseseeeesesneeeenseeseeenesnnsoneeees 1 17 Getting Started Equipment checklist ccccccscseseseecceceeeeeeeeeeeeeseeeeeesaeaesssessesssneaeaaes 2 1 GCOMVE MCI ONS os sis cise sada cess cases chee cates aAa ec Ta adaa aai aidad aaa eE 2 1 Short modelNnamMme as foes cS coe ecg ces ses acc fates a ng aaa aiaa dassoen faa sseaneeneceds 2 2 Using your computer for the fi
49. TOSHIBA Support In addition to the information in this section also refer to the documentation supplied with your USB device User s Manual User s Manual Problem USB device does not work Procedure Remove the USB device from the computer and then reconnect it to a free port in order to ensure that it is firmly attached Ensure that any required USB device drivers are properly installed To achieve this you should refer to both the device documentation and the operating system documentation Sleep and Charge function For more information and settings refer to the Sleep and Charge section Problem cannot use the Sleep and Charge function The battery depletes quickly even when turned OFF the power of the computer Procedure Sleep and Charge function might be disabled Enable the Sleep and Charge function in the TOSHIBA HWSetup When there is a current overflow of the external device connected to the compatible port USB bus power DC5V supply might be stopped for safety reasons When this happens disconnect an external device if some external devices are connected After that turn the power of the computer ON OFF to restore the function If this function cannot be still used even if only one external device is connected stop using the external device because its current is over the acceptable value of this computer Some external devices might not be able to use the Sleep and Charge functi
50. W 120W ccessseeeees 4 27 Chapter 5 Chapter 6 Chapter 7 User s Manual Sec rity JOCK vissinieccnseccntecceionneveestiteeveteceustmeaesvieeaseaedeudsnerdesaneeeenaeeucdinentss 4 29 Optional TOSHIBA Accessories ececeeeeeteeeeeeeneeeeesesenseeeeenennnneeenes 4 29 Sound System and Video mode csecceeseeeeeeeeeneeeeeeeeeneeeeeenennsneeenes 4 29 Utilities and Advanced Usage Utilities and Applications ccccceeeeeeeeeee ee eeeeeeeeeeeseeeeeeeeeeeeeeeeeeeeees 5 1 Spe cial features eee ee ap ee ee e iana 5 3 Using the TOSHIBA Sleep Utility 0 00 0 eeccesseceeeeeeeeeeseeseeeeeeeeeeneeeenees 5 5 TOSHIBA Password Utility ccccecessseeeeseeeeeseeeeseeeeeeseeneeeseeesnsneeenes 5 7 TOSHIBA HWSetup jiccscccectccctccsccpesececcsevstheccacsecttetetcccteecibeseceauecsetoneeuens 5 10 TOSHIBA PC Health Monitor ccscccscsscceseeceeeeeeeneeeeeseeeeeseneeseeeeees 5 11 Using the Hard Disk Drive HDD Protection cseeeeeee 5 12 TOSHIBA Setup Utility 20 cece esses eeeeeeeeeeeeeeeeeeseeeeeeeeeeenseeeeeeeseees 5 14 System Recovery ou cceeecceseeeeeeseeeeeeeeeeeseeeesnseneeseeeesnseeeeeeeeeseeeseesnnsnneenes 5 15 Troubleshooting Problem Solving procesS ccccceeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeseeeees 6 1 Hardware and system Checklist 2 cccccesseeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeees 6 4 TOSHIBA support sccecictscecceccsndannccecstuensctines snenesuereccana
51. Working environment This product was designed to fulfil the EMC Electromagnetic Compatibility requirements to be observed for so called Residential commercial and light industry environments TOSHIBA do not approve the use of this product in working environments other than the above mentioned Residential commercial and light industry environments For example the following environments are not approved E Industrial Environments e g environments where a mains voltage of 380 V three phase is used m Medical Environments Automotive Environments E Aircraft Environments Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA The consequences of the use of this product in non approved working environments may be E Interference with other devices or machines in the near surrounding area Malfunction of or data loss from this product caused by disturbances generated by other devices or machines in the near surrounding area Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non approved working environments before use In the case of automobiles or aircraft the manufacturer or airline respectively should be asked for permission before use of this product Furthermore for general safety reasons the use of this product in environments with explosive at
52. ack can explode if not replaced used handled or disposed of properly Use only batteries recommended by TOSHIBA as replacements Charge the battery pack only in an ambient temperature from 5 through 35 degrees Celsius Otherwise the electrolyte solution might leak battery pack performance might deteriorate and the battery life might be shortened Charging the batteries User s Manual When the power in the battery pack becomes low the DC IN Battery indicator flashes amber to indicate that only a few minutes of battery power remain If you continue to use the computer while the DC IN Battery indicator flashes the computer enters Hibernation Mode so that you do not lose any data and automatically turn itself off You must recharge the battery pack when it becomes discharged Procedures To recharge a battery pack connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet The DC IN Battery indicator glows amber while the battery is being charged Charging Time Refer to User Information Guide about charging time Charging notice The battery might not begin charging immediately under the following conditions m The battery is extremely hot or cold if the battery is extremely hot it might not charge at all To ensure the battery charges to its full capacity charge it at room temperature of between 5 C to 35 C 41 95 F m The battery is nearly completely discharged In this instanc
53. al charge and cause an electrical shock or minor bodily injury when touched As a general safety precaution avoid touching any metal parts m Never place your computer or AC adaptor on a wooden surface furniture or any other surface that might be marred by exposure to heat since the computer base and the surface of the AC adaptor increase in temperature during normal use m Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions 1 Connect the power cord to the AC adaptor Figure 2 1 Connecting the power cord to the AC adaptor 2 pin plug A ji Figure 2 2 Connecting the power cord to the AC adaptor 3 pin plug Pie Either a 2 pin or 3 pin adaptor cord is included with the computer depending on the model 2 Connect the DC output plug of the AC adaptor to the DC IN 19V jack on your computer 3 Plug the power cord into a live wall outlet The DC IN Battery indicator glows Figure 2 3 Connecting the DC output plug to the computer Z30 B 1 DC IN 19V jack 2 DC output plug Product appearance depends on the model you purchased Opening the display The display panel can be opened to a wide range of angles for optimal viewing While holding down the palm rest with one hand so that the main body of the computer is not raised slowly lift the display panel
54. aptor has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Refer to Operating Basics for details nia Do not connect any cable other than a LAN cable to the LAN jack It might cause damage or malfunction DC IN 19V jack The AC adaptor connects to this jack to power the computer and charge its internal batteries Note that you must only use the model of AC adaptor supplied with the computer at the time of purchase Using the wrong AC adaptor can damage the computer oce DC IN 19V Gc Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer Back Z40 B The following figure shows the back of the computer Figure 3 10 The back of the computer Z40 B y Product appearance depends on the model you purchased Underside Z40 B The following figures show the underside of the computer Ensure that the display is closed before the computer is turned over to avoid causing any damage User s Manual 3 15 Figure 3 11 The underside of the computer Z40 B ammam 1 Cooling vents 2 Docking port Provided with some models Product appearance depends on the model you purchased Cooling vents The cooling vents help the processor to avoid overheating Do
55. ar There are the following conditions for HDD Protection icon Normal TOSHIBA HDD Protection is enabled Protection TOSHIBA HDD Protection is active The HDD head is in a safe position OFF TOSHIBA HDD Protection is disabled Detection Level There are four sensitivity levels in which vibrations impacts and their similar signs are detected can be set to OFF 1 2 and 3 in ascending order Level 3 is recommended for better protection of the computer However when the computer is used in a mobile environment or in other unstable conditions setting the detection level to 3 could result in frequent execution of HDD Protection which will slow down HDD reading and writing Set a lower detection level when the speed of HDD reading and writing is a priority Different detection levels can be set depending on whether the computer is used as handheld or mobile usages or whether it is used in a stable environment such as on a table in the workplace or at home By setting different detection levels for the computer depending on whether it runs with the AC power desktop or with batteries handheld or mobile usage the detection level automatically switches according to the power connection mode T Detection Level Amplification When the AC adaptor is disconnected HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds Default You can reset HDD Protection settings to factory
56. ard to it If all USB ports have the Sleep and Charge function change to disable Sleep and Charge function The USB Wakeup function now works but the Sleep and Charge function is disabled Metal paper clips or hair pins clips can generate heat if they come into contact with USB ports Do not allow USB ports to come into contact with metal products for example when carrying the computer in your bag Starting the TOSHIBA Sleep Utility To start the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Sleep Utility Enabling Sleep and Charge This utility can be used to enable and disable the Sleep and Charge function Select the Enable Sleep and Charge check box to enable this function for the compatible USB ports The default state is disabled Power supply mode settings Your PC has multiple charging modes so that many different USB devices can be supported for Sleep and Charge function Auto Mode Default is suitable for a wide range of digital audio players However determining which mode is suitable for your USB device is unknown without trying Try each mode using the following procedure from Auto Mode to Alternate Mode to find the suitable mode for your USB device to charge This function might not be able to be used with some connected external devices even if the appropriate mode is selected In this situation clear the Enable Sleep and Charge check box and stop using this function
57. ayments This section contains information on the proper use of the Smart Card slot and it is strongly recommended that you read it before operating the computer Some models are equipped with a Smart Card slot Your computer supports ISO7816 3 asynchronous cards support protocols are T 0 and T 1 with a working voltage of 5 V Inserting a Smart Card User s Manual The Smart Card slot is on the side of the computer The Windows hot install feature allows you to insert a Smart Card while the computer is turned on To install a Smart Card do the following 1 Insert the Smart Card into the Smart Card slot with the metal connectors facing up 2 Press the Smart Card gently to ensure a firm connection is made The computer will identify the Smart Card and display an icon in the Windows Taskbar m When inserting a Smart Card into the Smart Card slot make sure to confirm that the card is oriented correctly before inserting E nsert the Smart Card until it reaches the end of the Smart Card slot The Smart Card is partially extended beyond the chassis edge Do not attempt to insert it further m Always remove the Smart Card from the Smart Card slot before moving the computer E Remove the Smart Card after use Failure to follow these instructions might result in damage to the computer and or damage to the Smart Card 4 23 3 After inserting the Smart Card you should refer to its documentation and also check the con
58. by either turning on the fan first then if necessary lowering the processor speed or by lowering the processor speed first then if necessary turning on the fan Both of these functions are controlled through the Power Options When the processor s temperature falls within normal range the fan and the processor operation will return to its standard speed If the processor s temperature reaches an unacceptably high level with either setting the computer automatically shuts down to prevent any damage In this instance all unsaved data in memory will be lost Using the TOSHIBA Sleep Utility User s Manual The TOSHIBA Sleep Utility is used for changing settings of the following function s m Sleep and Charge It also displays the remaining battery capacity Sleep and Charge T User s Manual Your computer can supply USB bus power DC5V to the USB port even when the power of the computer is turned OFF Power OFF includes Sleep Mode Hibernation Mode or shutdown state This function can be used for ports that support the Sleep and Charge function The port with the icon 4 has Sleep and Charge function You can use the Sleep and Charge function to charge certain USB compatible external devices such as mobile phones or portable digital music players E The Sleep and Charge function might not work with certain external devices even if they are compliant with the USB specification In those cases turn the power of
59. cense or another one contracted with the authors grants you the right to use distribute and modify it Therefore by using distributing or modifying the FreeType Project you indicate that you understand and accept all the terms of this license 4 Contacts There are two mailing lists related to FreeType E freetype nongnu org Discusses general use and applications of FreeType as well as future and wanted additions to the library and distribution If you are looking for support start in this list if you haven t found anything to help you in the documentation m freetype devel nongnu org Discusses bugs as well as engine internals design issues specific licenses porting etc Our home page can be found at http www freetype org ENERGY STAR Program D ENERGY STAR Your Computer model may be ENERGY STAR compliant If the model you purchased is compliant it uses the Energy Star logo and the following information applies TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes To conserve energy your computer is set to enter the low power Sleep Mode which shuts down the system and display within 15 minutes of inactivity in
60. cept this risk do not register the HDD SSD User Password E When saving the HDD SSD User Password shut down or restart the computer If the computer is not shut down or restarted the saved data might not be correctly reflected For more information on shutting down or restarting the computer refer to Turning on the power Supervisor Password If you set a Supervisor Password some functions might be restricted when a user logs on with the User Password You can start the Supervisor Password utility by accessing the following folder and then double click TOSPU exe C Program Files TOSHIBA PasswordUtility or C Program Files x86 TOSHIBA Passwordutility This utility lets you do the following H Register or delete the Supervisor Password E Specify restrictions for general users Starting the computer using a password i A User s Manual If you have already registered a user password there is one way to start the computer Enter the password manually The password is necessary only if the computer was shut down in Hibernation mode or boot mode It is not needed in Sleep mode and Restart To enter a password manually do the following 1 Turn on the power as described in the Getting Started section The following message appears in the screen Password At this point the function keys do not work They will function after you enter the password 2 Enter the Password A 3 Press ENTER If y
61. ck Apply Save successfully is displayed Click OK Click Close Do you want to quit is displayed Click OK It will be returned to the TOSHIBA Fingerprint Utility main menu Oy CoO This modified configuration for fingerprint Pre Boot authentication and Single Sign On feature becomes effective the next time the system is booted up This section explains battery types use recharging methods and handling Battery types User s Manual The computer has different types of batteries Battery pack When the AC adaptor is not connected the main power source of the computer is the lithium ion battery also referred to in this manual as the main battery Real Time Clock RTC function The Real Time Clock RTC function is supported The battery pack provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off If the RTC lasting time completely runs out the system will lose this information and the real time clock and calendar will stop working You can change the Real Time Clock settings in the BIOS setup utility Refer to Troubleshooting for further information Care and use of the battery pack A This section provides the important safety precautions in order to handle your battery pack properly Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions m The battery p
62. cking port This port enables connection of an optional TOSHIBA Hi Speed Port Replicator II 180W 120W described in TOSHIBA Hi Speed Port Replicator III 180W 120W Some models are equipped with the docking port 1 Only the TOSHIBA Hi Speed Port Replicator III 180W or 120W is IJ compatible with the docking port E Do not attempt to use any other Port Replicator E Keep foreign objects out of the docking port A pin or similar object can damage the circuitry of the computer Front with the display open Z40 B This section shows the computer with the display panel open To open the display lift up the display panel and position it at a comfortable viewing angle for you User s Manual 3 16 User s Manual Figure 3 12 The front of the computer with the display panel open Z40 B 1 Wireless communication antennas 10 AccuPoint control buttons not shown 2 Microphones 11 Touch Pad ON OFF indicator 3 Web Camera LED 12 TOSHIBA eco indicator 4 Web Camera 13 Touch Pad 5 Display screen 14 Touch Pad control buttons 6 Display hinges 15 Fingerprint Sensor 7 Keyboard 16 DC IN Battery indicator 8 Power button 17 Power indicator 9 AccuPoint 18 Internal storage drive indicator Provided with some models Product appearance depends on the model you purchased Wireless Depending on the configuration of your communication computer one or all of the following antennas are
63. d Cooling vents The cooling vents help the processor to avoid overheating User s Manual 3 6 Docking port This port enables connection of an optional TOSHIBA Hi Speed Port Replicator II 180W 120W described in TOSHIBA Hi Speed Port Replicator II 180W 120W Some models are equipped with the docking port m Only the TOSHIBA Hi Speed Port Replicator Ill 180W or 120W is compatible with the docking port Donot attempt to use any other Port Replicator m Keep foreign objects out of the docking port A pin or similar object can damage the circuitry of the computer Front with the display open Z30 B User s Manual This section shows the computer with the display panel open To open the display lift up the display panel and position it at a comfortable viewing angle for you User s Manual Figure 3 6 The front of the computer with the display panel open Z30 B 1 Wireless communication antennas 10 AccuPoint control buttons not shown 2 Microphones 11 Touch Pad ON OFF indicator 3 Web Camera LED 12 TOSHIBA eco indicator 4 Web Camera 13 Touch Pad 5 Display screen 14 Touch Pad control buttons 6 Display hinges 15 Fingerprint Sensor 7 Keyboard 16 DC IN Battery indicator 8 Power button 17 Power indicator 9 AccuPoint 18 Internal storage drive indicator Provided with some models Product appearance depends on the model you purchased Wireless Dep
64. d E Toshiba meets all requirements of Turkish regulation 28300 Restriction of the use of certain hazardous substances in electrical and electronic equipment AEEE Y netmeli ine Uygundur Toshiba 28300 say l T rkiye Elektrikle ali an ve elektronik ekipmanda belirli tehlikeli maddelerin kullanimiyla ilgili kisitlama y netmeli i gereklerini tamamen yerine getirmektedir The number of possible pixel failures of your display is defined according to ISO 9241 307 standards If the number of pixel failures is less than this standard they will not be counted as defect or failure Battery is a consumption product since the battery time depends on the usage of your computer If the battery can not be charged at all then it is a defect or failure The changes in battery time is not a defect or failure Following information is only for India The use of this symbol indicates that this product may not be treated as household waste By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please visit our website http www toshiba india com or contact call center 1800 200 8674 These symbols might not stick depending on the country and region where you purchased User s Manual 1 7
65. d return it to its case E The card is designed so that it can be inserted only one way Do not try to force the card into the slot Do not leave a card partially inserted in the slot Press the card until you hear it click into place m Set the write protect switch to the lock position if you do not want to record data m Memory cards have a limited lifespan so it is important to back up important data H Do not write to a card if the battery power is low Low power might affect writing accuracy H Do not remove a card while read write is in progress For more details on using memory cards see manuals accompanying the cards About the write protect feature Memory media cards have a write protect function m SD Card SD memory card SDHC memory card and SDXC memory card Set the write protect switch to the lock position if you do not want to record data 4 21 Inserting memory media The following instructions apply to all types of supported media devices To insert memory media do the following 1 2 3 Turn the memory media so that the contacts metal areas face down Insert the memory media into the memory media slot on your computer Press the memory media gently until it clicks into place Figure 4 10 Inserting memory media Z30 B 1 Memory media slot 2 Memory media Product appearance depends on the model you purchased Make sure that the memory media is oriented properly before you inser
66. d a working power outlet Check the condition of the cord and terminals If the cord is frayed or damaged it should be replaced while if the terminals are soiled they should be cleaned with a clean cotton cloth If the AC adaptor still does not power the computer you should contact TOSHIBA Support If you suspect a problem with the battery check the status of the DC IN Battery indicator Problem Battery does not power the computer Battery does not charge when the AC adaptor is attached Battery does not power the computer as long as expected User s Manual Procedure The battery might be discharged Connect the AC adaptor to recharge the battery If the battery is completely discharged it will not begin charging immediately In these instances wait a few minutes before trying again If the battery still does not charge check that the power outlet the AC adaptor is connected to its supplying power This can be tested by plugging another appliance into it If you frequently recharge a partially charged battery the battery might not charge to its full potential In these instances you should fully discharge the battery and then attempt to charge it again Check the Power saver option under Select a power plan in the Power Options Real Time Clock Problem Procedure The BIOS setting The lasting time of the Real Time Clock RTC has and system date run out You must set the date and time in the
67. devices back on immediately Wait a short period to avoid any potential damage Restarting the computer A Certain conditions require that you reset the computer for example if E You change certain computer settings To restart the computer there are two ways this can be achieved Click Start Point to the arrow beside the Shut down button and then select Restart m Press CTRL ALT and DEL simultaneously once to display the menu window and then select Restart by clicking the power icon cy in the lower right corner Before restarting the computer be sure to save your data Sleep Mode T User s Manual If you have to interrupt your work you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode In this mode data is maintained in the main memory of the computer When you turn on the power again you can continue working right where you left off When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled always shut down the computer This includes turning off any wireless communication functionalities and canceling settings that reactivate the computer automatically such as a timer recording function Failure to shut down the computer in this way might allow the operating system to reactivate and run pre programmed tasks or preserve unsaved data which might interfere with aviation or other
68. e eject hole Gently pull to open the SIM card tray A Never pull the SIM card tray completely out of the slot User s Manual Figure 4 4 Open the SIM card tray with the eject hole Z30 B 1 Eject hole Place the SIM card into the SIM card tray with the metal connectors facing up Insert the SIM card tray into the SIM card slot and push the center of the tray to close it Press gently until it locks into place Figure 4 6 Installing the SIM Card Z30 B 1 SIM card slot 3 SIM card tray 2 SIM card AN E Never allow metal objects such as screws staples and paper clips to enter the computer Foreign metal objects can create a short circuit which can cause computer damage and fire possibly resulting in serious injury E Do not touch the connectors on the SIM card or on the computer Debris on the connectors might cause access problems Removing a SIM Card To remove the SIM card do the following 1 Click Start and then select Shut down 2 To pop the SIM card tray partially open insert a slender object about 10mm diameter 0 8mm such as a straightened paper clip into the eject hole Gently pull to open the SIM card tray 3 Remove the SIM card from the SIM card tray 4 Insert the SIM card tray back into the SIM card slot GPS Function Your computer might include a built in GPS Global Positioning System The performance of GPS varies depending on the environment Failure to pinpoint a location migh
69. e leave the AC adaptor connected for a few minutes and the battery should begin charging The DC IN Battery indicator might show a rapid decrease in battery operating time when you try to charge a battery under the following conditions m The battery has not been used for a long time m The battery has completely discharged and been left in the computer for a long time In such cases do the following 1 Fully discharge the battery with the power on until the system automatically turns itself off 2 Connect the AC adaptor to the DC IN 19V jack of the computer and to a wall outlet that is supplying power 3 Charge the battery until the DC IN Battery indicator glows white Repeat these steps two or three times until the battery recovers normal capacity Monitoring battery capacity Remaining battery power can be monitored using the following methods H Clicking the battery icon on the Windows Taskbar H Via the Battery Status in the Windows Mobility Center window l Wait several seconds to monitor the remaining operating time because D the computer needs time to check the remaining capacity of the battery pack and then calculate the remaining operating time based on this together with the current power consumption E Be aware that the actual remaining operating time might differ slightly from the calculated time With repeated discharges and recharges the battery capacity will gradually decrease In view of this it
70. e AC adaptor when you create Recovery Media m Be sure to close all other software programs except the Recovery Media Creator Do not run software such as screen savers which can put a heavy load on the CPU Operate the computer at full power Do not use power saving features Do not write to the media when the virus check software is running Wait for it to finish then disable virus detection programs including any software that checks files automatically in the background Do not use utilities including those intended to enhance internal storage drive access speed They might cause unstable operation and damage data Do not shut down log off or Sleep Hibernate while writing or rewriting the media Set the computer on a level surface and avoid places subjected to vibrations such as airplanes trains or cars Do not use on an unstable surface such as a stand A recovery image of the software on your computer is stored on the internal storage drive and can be copied to either disc media or USB Flash Memory by using the following steps 1 Select either blank disc or USB Flash Memory The application allows you to choose from a variety of different media onto which the recovery image can be copied including disc media and USB Flash Memory Some of the disc media might not be compatible with the optical disc drive connected to your computer You should therefore verify that the optical disc drive supports the blank m
71. e Battery section Legal Footnote Battery Life For more information regarding Battery Life refer to the Legal Footnotes section CPU The processor type varies depending on model To check which type of processor is included in your model open the TOSHIBA PC Diagnostic Tool by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Diagnostic Tool Legal Footnote CPU For more information regarding CPU refer to the Legal Footnotes section Internal Storage Drive The capacity of the internal storage drive varies depending on the model To check which type of internal storage drive is included in your model open the TOSHIBA PC Diagnostic Tool by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Diagnostic Tool Note that part of the hard disk overall capacity is reserved as administration space 7 SSD is a large capacity storage device which uses Solid State Memory in J place of a magnetic disk of the hard disk User s Manual 3 20 Under certain unusual conditions of prolonged non use and or exposure to high temperatures the SSD might be vulnerable to data retention errors Legal Footnote Internal Storage Drive Capacity For more information regarding internal storage drive capacity refer to the Legal Footnotes section Video RAM The memory in the graphics adaptor of the computer used to store the image displayed on a bitmap display The amoun
72. e software if possible If an error message appears while you are using a software package you should refer to the documentation supplied with it as this usually includes a problem solving section or a summary of error messages Next check any error messages against the operating system documentation A Hardware If you cannot find a software problem you should then check the setup and configuration of your hardware First run through the items in the preliminary checklist as described previously then if you still cannot correct the problem try to identify the source The next section provides checklists for individual components and peripherals Before using a peripheral device or application software that is not an authorized TOSHIBA part or product make sure that the device or software can be used with your computer Use of incompatible devices might cause injury or might damage your computer If something goes wrong User s Manual Your computer does not respond to the keyboard commands If an error occurs and the computer does not respond to your keyboard commands do the following Press the power button and hold it down for five seconds Once the computer has turned itself off wait 10 15 seconds before turning on the power again by pressing the power button Your program stops responding If you are working with a program that suddenly freezes all operations chances are the program has stopped responding You can
73. eakerphones Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters m Extreme heat cold or humidity Liquids and corrosive chemicals Stress injury User s Manual Carefully read the nstruction Manual for Safety and Comfort It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use It also includes information on work space design posture and lighting that can help reduce physical stress Heat injury B Avoid prolonged physical contact with the computer If the computer is used for long periods its surface can become very warm While the temperature will not feel hot to the touch if you maintain physical contact with the computer for a long time for example if you rest the computer on your lap or if you keep your hands on the palm rest your skin might suffer a low heat injury m If the computer has been used for a long time avoid direct contact with the metal plate supporting the various interface ports as this can become hot m The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction If you need to transport the AC adaptor disconnect it and let it cool before moving it H Do not lay the AC adaptor on a material that is sensitive to heat as the material could become damaged Pressure or impact damage Do not apply heavy pressure t
74. echnology Remote BIOS update Legal Footnotes Non applicable Icons CPU User s Manual Certain computer chassis are designed to accommodate all possible configurations for an entire product series Therefore be aware that your selected model might not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis Central Processing Unit CPU Performance Legal Footnotes CPU performance in your computer product might vary from specifications under the following conditions Huse of certain external peripheral products muse of battery power instead of AC power Huse of certain multimedia computer generated graphics or video applications muse of standard telephone lines or low speed network connections Huse of complex modeling software such as high end computer aided design applications Huse of several applications or functionalities simultaneously Huse of computer in areas with low air pressure high altitude gt 1 000 meters or gt 3 280 feet above sea level use of computer at temperatures outside the range of 5 C to 30 C 41 86 F or gt 25 C 77 F at high altitude all temperature references are approximate and might vary depending on the specific computer model contact TOSHIBA support for details CPU performance might also vary from specifications due to design configuration Under some conditions your computer product might automatically shut down
75. edia you have chosen before proceeding USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding Turn on your computer and allow it to load the Windows operating system from the internal storage drive as normal Insert the first blank disc into the optical disc drive tray or insert the USB Flash Memory into one available USB port Click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Recovery Media Creator After Recovery Media Creator starts select the type of media and the title you wish to copy and then click the Create button Restoring the pre installed software from your created Recovery Media A User s Manual If the pre installed files are damaged you are able to use the Recovery Media you have created to restore the computer to the state it was in when you originally received it To perform this restoration do the following When you reinstall the Windows operating system the internal storage drive will be reformatted and all data will be lost i Make sure that the AC adaptor is connected during the restoring process 1 Load the Recovery Media into the external Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port 2 Click Start Point to the arrow beside the Shut down button and then select Restart 3 Hold down the F12 key and release this key one second after the computer is power on 4 U
76. ended to save power when operating on batteries For more information regarding LCD refer to the Legal Footnotes section Display hinges Keyboard Power button The display hinges allow the display panel to be positioned at a variety of easy to view angles The keyboard contains character keys control keys function keys and special Windows keys providing all the functionality of a full size keyboard Refer to the The Keyboard section for details Press this button to power on off the computer A ay User s Manual AccuPoint AccuPoint control buttons Touch Pad ON OFF indicator TOSHIBA eco indicator Touch Pad Touch Pad control buttons Fingerprint Sensor DC IN Battery indicator A pointer control device located in the center of the keyboard is used to control the on screen pointer Some models are equipped with an AccuPoint Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the on screen pointer Only models equipped with an AccuPoint are equipped with AccuPoint control buttons Double tap this indicator to enable disable the Touch Pad The indicator shows the status of the Touch Pad E Enabled off E Disabled glows white Double tap this indicator to launch the TOSHIBA eco Utility The Touch Pad located in the palm rest is used to control the movement of the on screen pointer To use the Touch Pad simply touc
77. ending on the configuration of your communication computer one or all of the following antennas are antennas built in E Wireless LAN Wireless LAN Bluetooth Legal Footnote Wireless LAN For more information regarding Wireless LAN refer to the Legal Footnotes section 3 8 T User s Manual Microphone Web Camera LED Web Camera The built in microphone allows you to record sounds for your application Refer to the Sound System and Video mode section for more information The Web Camera LED glows when the Web Camera is operating Web Camera is a device that allows you to record video or take photographs with your computer You can use it for video chatting or video conferences using a communication tool Some models are equipped with a Web Camera Do not point the web camera directly at the sun Do not touch or press strongly on the web camera lens Failure to do so might reduce image quality Use an eyeglass cleaner cleaner cloth or other soft cloth to clean the lens if it becomes dirty Display screen Legal Footnote LCD 33 8 cm 13 3 LCD screen configured with one of the following resolutions E HD 1366 horizontal x 768 vertical pixels FHD 1920 horizontal x 1080 vertical pixels Be aware that when the computer is operating on the AC adaptor the image displayed on the internal screen is somewhat brighter than when it operates on battery power This difference in brightness levels is int
78. eration The AC power can then be used to charge the battery during periods where power demand is reduced such as at night thereby reducing the load during peak periods To access the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Peak Shift Control For more information refer to the Help file The TOSHIBA PC Diagnostic Tool displays basic system configuration information and allows the functionality of some of the computer s built in hardware devices to be tested TOSHIBA The TOSHIBA Accessibility utility provides Accessibility support to movement impaired users when they need to use the function keys In use the utility allows you to make the FN key sticky that is you can press it once release it and they press one of the function keys in order to access its specific function When set the FN key remains active until another key is pressed Bluetooth Stack for This software enables communication between Windows by Toshiba the computer and external Bluetooth devices such as printers and mobile phones Bluetooth functions cannot be used in models that do not have a Bluetooth module installed TOSHIBA Password This utility allows you to set a password in order Utility to restrict access to the computer TOSHIBA eco Utility This computer is equipped with eco mode This mode slightly lowers performance of some devices to reduce electric power consumption You can realize meas
79. es can cause malfunction of such equipment possibly resulting in serious injury E It might not be possible to make a network connection to a specified network name using the ad hoc network function If this occurs the new network has to be configured for all computers connected to the same network in order to re enable network connections Make sure to use new network name Security TOSHIBA strongly recommends that you enable encryption functionality otherwise your computer is open to illegal access by an outsider using a wireless connection If this occurs the outsider might illegally access your system eavesdrop or cause the loss or destruction of stored data H TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof Card Specifications Compatibility IEEE 802 11 Standard for Wireless LANs Network Operating H Microsoft Windows Networking System Media Access mH CSMA CA Collision Avoidance with Protocol Acknowledgment ACK Radio Characteristics Radio Characteristics of Wireless LAN module might vary according to H Country region where the product was purchased E Type of product Wireless communication is often subject to local radio regulations Although Wireless LAN wireless networking products have been designed for operation in the license free 2 4 GHz and 5 GHz band local radio regulations might impose a number of limitations
80. es problems caused by your computer s hardware or attached peripherals Basic problems might occur in the following areas E Power m USB device m Keyboard m Sound system E Internal display panel m External monitor m HDD E LAN E Memory Media Card E Wireless LAN E Pointing Device E Bluetooth Power User s Manual When the computer is not plugged into an AC power outlet the battery pack is the primary power source Your computer also has Real Time Clock RTC function All of the power resources are interrelated with anyone having the ability to produce apparent power problems Overheating power down If the processor s temperature reaches an unacceptably high level with either setting the computer automatically shuts down to prevent any damage In this instance all unsaved data in memory is lost Problem Procedure Computer shuts Leave the computer off until it reaches room down automatically temperature If the computer has reached room temperature and it still does not start or if it starts but shuts down quickly contact TOSHIBA Support AC power If you have trouble turning on the computer with the AC adaptor connected check the status of the DC IN Battery indicator Refer to the Power Condition Descriptions section for further information Problem AC adaptor does not power the computer Battery Procedure Check the connections to make sure that the power cord adaptor is firmly connected to the computer an
81. ettings for When I press the power button and When I close the lid 4 Click the Save changes button User s Manual Data save in Hibernation Mode When you turn off the power in Hibernation Mode the computer takes a moment to save the current data in memory to the internal storage drive After you turn off the computer and the content of memory has been saved to the internal storage drive turn off the power to any peripheral devices Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Chapter 3 The Grand Tour This chapter identifies the various components of the computer It is recommended that you become familiar with each before you operate the computer Legal Footnote Non applicable Icons For more information regarding Non applicable Icons refer to the Legal Footnotes section P Handle your computer carefully to avoid scratching or damaging the surface The Grand Tour for Z30 B Front with the display closed Z30 B The following figure shows the front of the computer with the display panel in the closed position Figure 3 1 Front of the computer with display panel closed Z30 B Ti Se te 1 Stereo speakers 4 Internal storage drive indicator 2 DC IN Battery indicator 5 Wireless communication indicator 3 Power indicator 6 Wireless WAN WiMAX indicator Provided with some models Product appearance depends on the model y
82. evice from the USB port of your computer click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and then select the USB device that you want to remove Keep foreign metal objects such as screws staples and paper clips out of the USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury HDMI out port SIM Card slot Memory media slot HDMI out port can connect with Type A connector HDMI cable Some models are equipped with an HDMI out port This slot allows you insert a SIM card which enables a high speed access to the Internet corporate Intranet and your email while you are away from office Refer to the Wireless WAN device section for more information This slot lets you insert an SD SDHC SDXC memory card minisD microSD Card and MultiMediaCard Refer to the Memory media section for more information Keep foreign metal objects such as screws staples and paper clips out of the Memory media slot Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Right side Z40 B The following figures show the right side of the computer Figure 3 9 The right side of the computer Z40 B User s Manual z 9 E C a o REPARAR Eg NOQ lt amp 1 Smart Card slot 4 LAN jack 2 Headphone M
83. figuration in Windows to ensure that it is correct Removing a Smart Card To remove a Smart Card do the following 1 Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar E Before removing the Smart Card confirm that the Smart Card is not working with any program or system E Be careful not to bend the Smart Card while removing it from the computer 2 Point to Smart Card and click the left Touch Pad control button 3 Grasp the Smart Card and remove it External Display i Your computer video capabilities can be enhanced with additional displays External displays allow you to share your desktop or extend the desktop area As the port operation of all external monitors have not been confirmed some display devices might not function properly Connecting an external display i User s Manual Your computer comes with a built in display but you can also connect other external displays via available ports on the computer External RGB monitor port An external analog monitor can be connected to the External RGB monitor port on the computer To connect an external analog monitor do the following 1 Connect the RGB cable to the External RGB monitor port There are no fastening screws for an external monitor cable on the External RGB monitor port However external monitor cables which have connectors with fastening screws can still be used 2 Turn the external monitor s power on 4
84. fter approximately 5 to 7 seconds it is because the RTC lasting time runs out and the settings of AMT function have been cleared This is normal and not an error If it occurs the settings of AMT function must be reconfigured If there is a problem when you start the computer or initialize the Management Engine ME firmware after the RTC lasting time runs out the system will automatically reset itself during setup This is the function of AMT configurations and is not an error Enabling the AMT function might cause the network LAN Enable Disable items to be no longer changeable in BIOS setup utility Consult with your system administrator about details AMT function cannot be operated using a USB LAN adaptor The useable system memory for models equipped with the AMT function is 16 64 MB less than that of models not equipped with the AMT function The amount of the difference depends on the amount of memory installed Notes for system administrators User s Manual Intel AMT is enabled by default in the Management Engine ME firmware Both the security of management console and the network management must be thoroughly implemented through management of AMT function Otherwise administrator privileges might be abused by other parties which possibly lead to the leak of sensitive and or proprietary information data loss HDD SSD erasure or file overwritten The following functions are not supported RPAT Remote PC Assist T
85. h wireless technology has the following features Security Two advanced security mechanisms ensure a high level of security H Authentication prevents access to critical data and makes it impossible to falsify the origin of a message Encryption prevents eavesdropping and maintains link privacy Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2 4 GHz band which is license free and compatible with radio systems in most countries in the world Radio links You can easily establish links between two or more devices with these links being maintained even if the devices are not within a line of sight of each other Bluetooth Stack for Windows by TOSHIBA Please note that this software is specifically designed for the following operating systems E Windows 7 Information regarding the use of this software with these operating systems is listed below with further details being contained with the electronic help files supplied with the software ie This Bluetooth Stack is based on the Bluetooth specification depending on T the model you purchased However TOSHIBA cannot confirm the compatibility between any computing products and or other electronic devices that use Bluetooth other than TOSHIBA notebook computers Release Notes related to the Bluetooth Stack for Windows by TOSHIBA 1 Fax application software Please be aware that there is some fax application software that you cannot use
86. h and move your fingertip across it in the direction you want the on screen pointer to go The two buttons located on the bottom of the Touch Pad are used like the buttons on a standard mouse Press the left button to select a menu item or to manipulate text or graphics designated by the pointer and press the right button to display a menu or other function depending on the software you are using This sensor enables you to enroll and recognize a fingerprint Some models are equipped with a Fingerprint Sensor The DC IN Battery indicator shows the condition of the DC IN and the battery charge status White indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor Refer to the Power Condition Descriptions section for more information on this feature c Power indicator The Power indicator normally glows white when the computer is turned on However if you turn the computer off into Sleep Mode this indicator flashes amber 3 Internal storage drive The Internal storage drive indicator blinks indicator white whenever the computer is accessing the internal storage drive The Grand Tour for Z40 B Front with the display closed Z40 B The following figure shows the front of the computer with the display panel in the closed position Figure 3 7 Front of the computer with display panel closed Z40 B a ah T 1 Stereo speakers 4 Internal storage
87. hanges gt Yes The computer restarts immediately System Recovery There is a hidden partition allocated on the internal storage drive for the System Recovery Options in the event of a problem You can also create recovery media and restore the system The following items are described in this section H Creating Recovery Media m Restoring the pre installed software from your created Recovery Media Restoring the pre installed software from the Recovery Solid State Drive System Recovery Options i The System Recovery Options feature is installed on the hard disk when shipped from the factory The System Recovery Options menu includes tools to repair startup problems run diagnostics or restore the system See the Windows Help and Support content for more information about Startup Repair The System Recovery Options can also be run manually to repair problems The procedure is as follows Follow the instructions shown on the on screen menu 1 Turn off the computer 2 While holding the F8 key turn on the computer 3 The Advanced Boot Options menu is displayed Use the arrow keys to select Repair Your Computer and press ENTER 4 Follow the on screen instructions Check your Windows manual for more information on backing up your system including the system image backup feature Creating Recovery Media i User s Manual This section describes how to create Recovery Media m Be sure to connect th
88. hat is power settings battery temperature and recharging for models with battery CPU memory backlight illumination time and temperatures for various devices The collected information is not limited to the examples specified here The stored data uses a very small portion of the total hard disk capacity approximately 10 MB or less per year This information is used to identify and provide a notification of system conditions which might affect the performance of your TOSHIBA computer It might also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA authorized service providers Additionally TOSHIBA might also use this information for quality assurance analysis Subject to the use restrictions above the data on the internal storage drive logged might be transferred to entities located outside of your country or region of residence for example European Union Those countries might or might not have the same data protection laws or data protection levels as required by your home country or region You can disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel Doing so will automatically delete all collected information from the internal storage drive The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA obligations under its standard limited warranty in any way TOSHIBA standard limited warranty terms and l
89. he left button to select a menu item or to manipulate text or graphics designated by the pointer and press the right button to display a menu or other function depending on the software you are using This sensor enables you to enroll and recognize a fingerprint Some models are equipped with a Fingerprint Sensor The DC IN Battery indicator shows the condition of the DC IN and the battery charge status White indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor Refer to the Power Condition Descriptions section for more information on this feature The Power indicator normally glows white when the computer is turned on However if you turn off the computer into Sleep Mode this indicator flashes amber The Internal storage drive indicator blinks white whenever the computer is accessing the internal storage drive Internal Hardware Components This section describes the internal hardware components of your computer The actual specifications might vary depending on the model you purchased Battery pack This computer includes a battery pack inside However do not attempt to dismount or replace it by yourself Contact an authorized TOSHIBA service provider if necessary The rechargeable lithium ion battery pack provides power to the computer when the AC adaptor is not connected For more detailed information on the use and operation of the battery pack refer to th
90. icrophone jack 5 DC IN 19V jack 3 Universal Serial Bus USB 3 0 ports 6 Security lock slot Provided with some models Product appearance depends on the model you purchased Smart Card slot Headphone Microphone jack Universal Serial Bus USB 3 0 ports This slot allows you to install a Smart Card device Some models are equipped with a Smart Card slot A 3 5 mm mini headphone microphone jack enables connection of a monaural microphone or a stereo headphone Two Universal Serial Bus ports which comply to the USB 3 0 standard are provided on the right side of the computer The USB 3 0 port is compliant with USB 3 0 standard and backward compatible with USB 2 0 devices USB 3 0 port s might work as USB 2 0 port s when operating in USB Legacy Emulation mode Note that it is not possible to confirm the operation of all functions of all USB devices that are available Some functions associated with a specific device might not operate properly Before removing a USB device from the USB port of your computer click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and then select the USB device that you want to remove AN Keep foreign metal objects such as screws staples and paper clips out of the USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury LAN jack This jack lets you connect to a LAN The ad
91. ights granted herein subject to the following conditions H Redistribution of source code must retain this license file FTL TXT unaltered any additions deletions or changes to the original files must be clearly indicated in accompanying documentation The copyright notices of the unaltered original files must be preserved in all copies of source files Redistribution in binary form must provide a disclaimer that states that the software is based in part of the work of the FreeType Team in the distribution documentation We also encourage you to put an URL to the FreeType web page in your documentation though this isn t mandatory These conditions apply to any software derived from or based on the FreeType Project not just the unmodified files If you use our work you must acknowledge us However no fee need be paid to us 3 Advertising User s Manual Neither the FreeType authors and contributors nor you shall use the name of the other for commercial advertising or promotional purposes without specific prior written permission We suggest but do not require that you use one or more of the following phrases to refer to this software in your documentation or advertising materials FreeType Project FreeType Engine FreeType library or FreeType Distribution As you have not signed this license you are not required to accept it However as the FreeType Project is copyrighted material only this li
92. igital Versatile Disc Digital Versatile Disc recordable Digital Versatile Disc random Access Memory Digital Versatile Disc Recordable Dual Layer Digital Versatile Disc read Only Memory Digital Versatile Disc rewritable Digital Versatile Disc Recordable Double Layer File Allocation Table Federal Communications Commission Full High Definition gigabyte gigabytes per second High Definition High Definition Plus Hard Disk Drive High definition Multimedia Interface High definition Multimedia Interface Consumer Electronics Control Hypertext Markup Language 7 21 User s Manual IEEE 1 0 IRQ ISP KB LAN LCD LED MB MBps MMC OCR PC PCI PCMCIA RAM RGB RFI ROM RTC S P DIF SD SDHC SDXC SDRAM SSD TFT URL USB WAN WQHD www Institute of Electrical and Electronics Engineers Input Output interrupt request Internet Service Provider kilobyte Local Area Network Liquid Crystal Display Light Emitting Diode megabyte megabytes per second MultiMediaCard Optical Character Recognition Reader Personal Computer Peripheral Component Interconnect Personal Computer Memory Card International Association Random Access Memory Red Green and Blue Radio Frequency Interference Read Only Memory Real Time Clock Sony philips Digital Interface Format Secure Digital Secure Digital High Capacity Secure Digital Extended Capacity Synchronous Dynamic Random Access Memory
93. imitations apply Starting the TOSHIBA PC Health Monitor i The TOSHIBA PC Health Monitor can be opened by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Health Monitor The TOSHIBA PC Health Monitor main screen is displayed This utility might be disabled by default on your computer You can enable it by clicking Please click here to enable TOSHIBA PC Health Monitor The PC Health Monitor Software Notice amp Acceptance screen is displayed Carefully read the information displayed Selecting ACCEPT and clicking OK enables the program By enabling the TOSHIBA PC Health Monitor software you agree with these terms and conditions and to the use and sharing of the collected information Once the program is enabled the TOSHIBA PC Health Monitor screen is displayed and the program begins monitoring system functions and collecting information A message is displayed if any changes which might interfere with the operation of the program are detected Follow the instructions displayed on screen in the message Using the Hard Disk Drive HDD Protection i Some models have the function for reducing the risk of damage on the HDD Using an acceleration sensor built into the computer HDD Protection detects vibration shocks and similar signs of movement of the computer and automatically moves the HDD head to a safe position to reduce the risk of damage that could be caused by head to disk contact
94. information in this section also refer to the documentation supplied with your audio device Problem No sound is heard Annoying sound is heard Procedure Press the function keys to increase or decrease volume Check the software volume settings Check to see if Mute is turned to Off Check to make sure that the headphone connection is secure Check within the Windows Device Manager application to ensure that the sound device is enabled and that the device is properly working In this instance you might be experiencing feedback from either the internal microphone or an external microphone connected to the computer Refer to Sound System and Video mode for further information Volume cannot be adjusted during Windows start up or shut down If you are still unable to resolve the problem contact TOSHIBA Support External monitor LAN User s Manual Also refer to Operating Basics and to the documentation supplied with your monitor for further information Problem Monitor does not turn on No display Display error occurs Problem Cannot access LAN Procedure After confirming that the monitor s power switch is on check the connections to make sure that the power cord adaptor is firmly connected to the monitor and to a working power outlet Try adjusting the contrast and brightness controls on the external monitor Press the function key in order to change the display priority and ensure that
95. internal LCD This feature can be used if the computer is E running under battery mode H using the internal LCD display only The Display Power Saving Technology feature is enabled as the factory default If you want to turn off this feature change it in the settings accordingly in the Intel HD Graphics Control Panel You can access this control panel in the following way 1 Right click on the desktop and click Graphics Properties 2 Click Power and then select On Battery from the drop down menu under Power in the upper left corner 3 Click Disable under Display Power Saving Technology 4 Click Apply 3 22 If you want to enable this feature click Enable under Display Power Saving Technology Power Condition Descriptions The computer operating capability and battery charge status are affected by different power conditions including whether an AC adaptor is connected and what the battery charge level is DC IN Battery indicator i Check the DC IN Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected The following indicator conditions should be noted Flashing Amber The battery charge is low The AC adaptor must be connected to recharge the battery Amber Indicates that the AC adaptor is connected and the battery is charging White Indicates that the AC adaptor is connected and the battery is fully charged Flashing White Indicates a problem with
96. ions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http Awww openssl org 4 The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission For written permission please contact openssl core openssl org User s Manual 5 Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project 6 Redistributions of any form whatsoever must retain the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http Awww openssl org THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO
97. key activates the Windows Start menu E This key has the same function as the secondary right mouse button Using the AccuPoint To use the AccuPoint simply push it with your finger tip in the direction you want to move the on screen pointer Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad Some models are equipped with an AccuPoint AccuPoint precautions User s Manual Certain conditions can affect the on screen pointer when using AccuPoint For example the pointer might travel contrary to AccuPoint operation or an error message might appear if You touch the AccuPoint during power up H You apply constant soft pressure during power up m There is a sudden temperature change H Strong stress is applied to the AccuPoint If an error message appears reboot the computer If an error message does not appear wait a moment for the pointer to stop then continue operation Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use The spare AccuPoint cap is supplied with some models 1 F To remove the AccuPoint cap gently dig the cap out with finger Figure 4 2 Removing the AccuPoint cap Z30 B 1 AccuPoint cap Product appearance depends on the model you purchased Position a new cap on the peg and press it into place The peg is square so be careful to align the cap s square hole with the peg
98. less communication function of the computer is on If problems persist contact your LAN administrator Procedure Check to ensure that the wireless communication function of the computer is on Check to ensure that the Bluetooth Manager application is running on the computer and that power to the external Bluetooth device is turned on Check to ensure that no optional Bluetooth Adaptor is installed in the computer The built in Bluetooth hardware cannot operate simultaneously with another Bluetooth controller If you are still unable to resolve the problem contact TOSHIBA Support If you require any additional help using your computer or if you are having problems operating the computer you might need to contact TOSHIBA for additional technical assistance Before you call Some problems you experience might be related to software or the operating system so it is important that you investigate other sources of assistance first Before contacting TOSHIBA try the following Review troubleshooting sections in the documentation supplied with your software and or peripheral devices User s Manual E Ifa problem occurs when you are running software applications consult the software documentation for troubleshooting suggestions and consider calling the software company s technical support department for assistance m Consult the reseller or dealer from where you purchased your computer and or software they are your bes
99. ly but a few might require help from TOSHIBA Support If you find you need to consult others be prepared to describe the problem in as much detail as possible Preliminary checklist User s Manual You should always consider the simplest solution first The items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem m Make sure that you turn on all peripheral devices before you turn on the computer this includes your printer and any other external device you are using H Before you attach an external device you should first turn off the computer then when you turn the computer back on it recognizes the new device m Make sure that all optional accessories are configured properly in the computer s setup program and that all required driver software has been loaded refer to the documentation included with the optional accessories for further information on its installation and configuration m Check all cables to ensure that they are correctly and firmly attached to the computer loose cables can cause signal errors E Inspect all connecting cables for loose wires and all connectors for loose pins m Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them ina permanent error log this helps you to describe your problems to TOSHIBA Support In addition if a problem recurs the log you have made helps to identify the problem
100. m We don t promise that this software works However we will be interested in any kind of bug reports as is distribution m You can use this software for whatever you want in parts or full form without having to pay us royalty free usage m You may not pretend that you wrote this software If you use it or only parts of it in a program you must acknowledge somewhere in your documentation that you have used the FreeType code credits We specifically permit and encourage the inclusion of this software with or without modifications in commercial products We disclaim all warranties covering The FreeType Project and assume no liability related to The FreeType Project Finally many people asked us for a preferred form for a credit disclaimer to use in compliance with this license We thus encourage you to use the following text Portions of this software are copyright C lt year gt The FreeType Project www freetype org All rights reserved Please replace lt year gt with the value from the FreeType version you actually use Legal Terms Throughout this license the terms package FreeType Project and FreeType archive refer to the set of files originally distributed by the User s Manual authors David Turner Robert Wilhelm and Werner Lemberg as the FreeType Project be they named as alpha beta or final release You refers to the licensee or person using the project where
101. main menu Delete all users fingerprints 1 ob aN N In the TOSHIBA Fingerprint Utility main menu click Run as administrator User Account Control window is displayed Click Yes Swipe your enrolled finger Select Fingerprint Management option A list of fingerprint information for all users is shown in the screen Click the enrolled fingerprint data you want to delete and then click Delete Selected Items Do you want to delete the selected fingerprints message box appears on the screen Click OK Click Close Do you want to quit is displayed Click OK It will be returned to the TOSHIBA Fingerprint Utility main menu Windows Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password fingerprint authentication also allows logon to Windows User s Manual T This is useful especially when many users are using the PCs as user selection can be skipped Fingerprint Authentication Procedure 1 Start up the computer 2 The Logon Authorization screen is displayed Choose any of the enrolled fingers and swipe the fingerprint on the sensor If authentication is successful the user will be logged on to Windows m f the fingerprint authentication fails please logon using the Windows logon password E A warning message will be displayed when authentication is abnormal or authentication is not successful within a fixed duration Fingerprint Pre Boot authentication and Single
102. mately 3 GB only depending on the hardware specifications of the computer This is correct because the operating system usually displays the available memory instead of the physical memory RAM built into the computer Various system components like the video adapter s GPU and PCI devices like Wireless LAN and so on require their own memory space Since a 32 bit operating system cannot address more than 4 GB of memory these system resources overlap the physical memory It is a technical limitation that the overlapped memory is not available to the operating system Even though some tools might display the actual physical memory built into your computer the memory available to the operating system is still approximately 3 GB only Computers configured with a 64 bit operating system can address 4 GB or more of system memory Battery Life User s Manual Battery life might vary considerably depending on product model configuration applications power management settings and features utilized as well as the natural performance variations produced by the design of individual components Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication Recharge time varies depending on usage Battery might not charge while computer is consuming full power After going through many charge and discharge cycles the battery loses its ability to perform at maximum capacity and
103. mentation online or textual provided with the package Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgement This product includes cryptographic software written by Eric Young eay cryptsoft com The word cryptographic can be left out if the rouines from the library being used are not cryptographic related 4 Ifyou include any Windows specific code or a derivative thereof from the apps directory application code you must include an acknowledgement This product includes software written by Tim Hudson tih cryptsoft com THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO
104. mmfelddamm 8 41460 Neuss Germany The complete and official EU Declaration of Conformity can be found on TOSHIBA s web site http epps toshiba teg com on the Internet CE compliance This product is labeled with the CE Mark in accordance with the related European Directives notably RoHS Directive 2011 65 EU and Electromagnetic Compatibility Directive 2004 108 EC for the notebook and the electronic accessories including the supplied power adapter the Radio Equipment and Telecommunications Terminal Equipment Directive 1999 5 1 3 User s Manual EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006 95 EC for the supplied power adapter Furthermore the product complies with the Ecodesign Directive 2009 125 EC ErP and its related implementing measures This product and the original options are designed to observe the related EMC Electromagnetic Compatibility and safety standards However TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented In this case the persons who have connected implemented those options cables have to provide assurance that the system PC plus options cables still fulfils the required standards To avoid general EMC problems the following guidance should be noted E Only CE marked options should be connected implemented m Only best shielded cables should be connected
105. mory cards and SDXC memory cards m SD SDHC and SDXC memory cards appear the same externally However the logo on memory cards is different so pay careful attention to the logo when purchasing 7 E The SD memory card logo is S5 The SDHC memory card logo is The SDXC memory card logo is 2 The maximum capacity of SD memory cards is 2 GB The maximum capacity of SDHC memory cards is 32 GB The maximum capacity of SDXC memory cards is 128 GB Memory media format New media cards are formatted according to specific standards If you wish to reformat a media card be sure to do so with a device that uses media cards User s Manual 4 20 Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards If you reformat a memory card be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards not with the format command provided within Windows To format all areas of the memory card including the protected area you must obtain an appropriate application that applies the copy protection system Media care User s Manual Observe the following precautions when handling the card amp Do not twist or bend cards H Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid E Do not touch the metal part of a card or expose it to liquids or let it get dirty After using car
106. mospheres is not permitted VCCI Class B Information Japan Only CORBIS PIABRAMRE CT COREL Ria TCE FASS Cee BW CLCWETA CORBMNISAPTLE VAL SB ICIEL CRA SNSC SMBS SROTCEMHVET Friar BABE gt TELL RY RWSL TEAL VCCI B Canadian regulatory information Canada only This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications Note that Canadian Department of Communications DOC regulations provide that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Following information is only valid for EU member States Disposal of products User s Manual s The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste Integrated batteries and accumulators can be disposed of with the product They will be separated at the recycling centres The black bar indicates that the product was placed on the market after August 13 2005 By participating in the separate collection of products and batteries you will help to a
107. n Mode 1 Sleep Mode This feature automatically cuts off power to the computer s display panel when there is no keyboard input for a specified time with power being restored the next time a key is pressed This can be specified in the Power Options This feature automatically cuts off power to the internal storage drive when it is not accessed for a specified time with power being restored when the internal storage drive is next accessed This can be specified in the Power Options This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time This can be specified in the Power Options Two levels of password security supervisor and user are available to prevent unauthorized access to your computer A microprocessor in the computer s intelligent power supply detects the battery s charge automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor This can be specified in the Power Options This feature lets you configure the computer in order to save battery power This can be specified in the Power Options This feature automatically turns power to the computer off when the display panel is closed and turns it back on when the display panel is opened This can be specified in the Power Options When battery power is exhau
108. n outlet on a circuit different from that to which the receiver is connected H Consult the dealer or an experienced radio TV technician for help Only peripherals complying with the FCC class B limits can be attached to this equipment Operation with non compliant peripherals or peripherals not i recommended by TOSHIBA is likely to result in interference to radio and TV reception Shielded cables must be used between the external devices and the computer s external RGB monitor port Universal Serial Bus USB 3 0 ports HDMI out port and Headphone Microphone jack Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3000 This information is only applicable for the countries regions where it is required EU Declaration of Conformity User s Manual This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA EUROPE GMBH Ha
109. n the power Z30 B Figure 2 7 Turning on the power Z40 B 1 Power button Product appearance depends on the model you purchased Initial setup The Windows Startup Screen is the first screen displayed when you turn on the power To install the operating system properly follow the on screen instructions on each screen 2 When it is displayed be sure to read the License Terms carefully T Turning off the power The power can be turned off in one of the following modes either Shut Down Mode Sleep Mode or Hibernation Mode Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the main screen of the operating system the next time it is turned on 1 Ifyou have entered data either save it to the internal storage drive or to other storage media 2 Make sure all disk disc activity has stopped before removing the disk disc A m f you turn off the power while a disk disc is being accessed you might lose data or damage the disk Never turn off the power while an application is running Failure to do so can cause data loss m Never turn off the power disconnect an external storage device or remove storage media during data read write Failure to do so can cause data loss ad Click Start and then select Shut down 4 Turn off any peripheral devices connected to your computer User s Manual 2 7 A Do not turn the computer or peripheral
110. nd Wireless LAN devices operate within the same radio frequency range and might interfere with one another If you use Bluetooth and Wireless LAN devices simultaneously you might occasionally experience a less than optimal network performance or even lose your network connection If you experience any such problem immediately turn off either one of your Bluetooth or Wireless LAN If you have any questions about using Wireless LAN or Bluetooth Module visit http www pc support global toshiba com In Europe visit http www toshiba europe com computers tnt bluetooth htm Wireless devices and your health Wireless products like other radio devices emit radio frequency electromagnetic energy The level of energy emitted by wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones Because wireless products operate within the guidelines found in radio frequency safety standards and recommendations TOSHIBA believes that wireless products are safe for use by consumers These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature In some situations or environments the use of wireless products might be restricted by the proprietor of the building or responsible representatives of the organization The
111. needs to be replaced This is a normal phenomenon for all batteries To purchase a new battery pack see the accessories information that is shipped with your computer Internal Storage Drive Capacity 1 Gigabyte GB means 10 1 000 000 000 bytes using powers of 10 The computer operating system however reports storage capacity using powers of 2 for the definition of 1 GB 230 1 073 741 824 bytes and therefore shows less storage capacity Available storage capacity will also be less if the product includes one or more pre installed operating systems such as Microsoft Operating System and or pre installed software applications or media content Actual formatted capacity might vary LCD Over a period of time and depending on the usage of the computer the brightness of the LCD screen will deteriorate This is an intrinsic characteristic of LCD technology Maximum brightness is only available when operating in AC power mode Screen dims when the computer is operated on battery power and you might not be able to increase the brightness of the screen Graphics Processing Unit GPU Graphics processing unit GPU performance might vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized when operating in AC power mode and might decrease considerably when operating in battery power mode Total Available Graphics Memory is the total of as a
112. ng system Keyboard Allows you to access the wake on keyboard function or to configure the backlight brightness USB Allows you to set conditions for USB SATA Allows you to set conditions for SATA LAN Allows you to set conditions for LAN Advanced Options Allows you to set conditions for a specific device or function i The settings or options explained here might vary depending on the model you purchased After you changed the settings a dialog box might appear to prompt you that the changes will take effect after the computer restarts Make sure to restart your computer immediately to apply these changes TOSHIBA PC Health Monitor User s Manual The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption battery health for models with battery and the system cooling informing you of significant system conditions This application recognizes the system and individual component serial numbers and tracks specific activities related to the computer and their usage The collected information includes device operation time and number of actuations or status changes that is number of power button and FN key combination uses AC adaptor battery for models with battery LCD fan for models with fan internal storage drive sound volume wireless communication functionalities and USB information date of initial system use and also computer and device usage t
113. ngerprint authentication when booting up Battery It is necessary to register the User BIOS Password and Windows Logon Password before using the Fingerprint Pre Boot authentication and this Fingerprint Single Sign On Feature Use the TOSHIBA Password Utility to register your User BIOS Password If Windows Logon is not the default for your system see Manual to register your Windows Logon Password Only one fingerprint authentication is required to replace the User BIOS Password and if applicable the HDD SSD Password and the Windows Logon Password How to Enable Fingerprint Pre Boot authentication and Single Sign On feature It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the Pre Boot authentication and Single Sign On feature You should check that your fingerprint is enrolled before configuring the settings 1 Logon as Administrator means a user has administrator privileges 2 Inthe TOSHIBA Fingerprint Utility main menu click Run As Administrator 3 User Account Control window is displayed Click Yes Swipe your finger across the fingerprint sensor 5 Select Setting in the main menu to open the Setting window You can gt Select Pre Boot authentication check box if you want to use the fingerprint Pre Boot authentication feature Select Pre Boot authentication and Single Sign On check boxes if you want to use the Single Sign On feature Cli
114. nnetdecannnstiendeunneenes 6 13 Appendix SPECIFICATIONS siicevccccssecdsnincancancacteencavsececevebuunns aaea aaa aaa aa aaa iadaaa aiaa 7 1 AC Power Cord and Connectors 2 ccccecesseeeceeeeeeeeeeeeeseeeeeneeeeeeeeaes 7 3 Information for Wireless Devices 2 cccesssecceeeeeeeeeeeeeeeeeeeeeeeeeees 7 4 Information about Intel AMT cccececceceeeeseeeeeeeeseeeeeeeeeseeeeeeeeeees 7 15 Legal FOOtnOteSS sssini anian annanassae 7 18 GI OSSANY sceccisscaccncvcasshsccetcactencid netearaiete Jacana cataescecvanciacs tevanetecedieataicciedcers 7 20 Index Chapter 1 TOSHIBA Legal Regulatory and Safety This chapter states the legal regulatory and safety information applicable to TOSHIBA computers Copyright Disclaimer and Trademarks Copyright 2015 TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein First edition January 2015 Copyright authority for music movies computer programs databases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner Copyrighted material can be reproduced only for personal use or use within the home Any other use beyond that stipulated above including conversion to digital format alteration transfer of copied material
115. nual Provide adequate ventilation Always make sure that your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet even if your computer is in Sleep Mode In this condition observe the following Never cover your computer or AC adaptor with any object m Never place your computer or AC adaptor near a heat source such as an electric blanket or heater m Never cover or block the air vents including those at the base of the computer m Always operate your computer on a hard flat surface Using your computer on a carpet or other soft material can block the vents m Always provide sufficient space around the computer Overheating your computer or AC adaptor could cause system failure computer or AC adaptor damage or a fire possibly resulting in serious injury Creating a computer friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using such as a printer Leave enough space around the computer and other equipment to provide adequate ventilation Otherwise they might overheat To keep your computer in prime operating condition protect your work area from E Dust moisture and direct sunlight E Equipment that generates a strong electromagnetic field such as stereo speakers other than speakers that are connected to the computer or sp
116. o open the Screen Resolution dialog click Start gt Control Panel gt Appearance and Personalization gt Display gt Change display settings If you are running some applications for example a 3D application or video playback you might see some disturbance flickering or frame dropping on your screen If that occurs adjust the resolution of display lowering it until the screen is displayed properly 4 32 Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer and the advanced usage of some utilities Utilities and Applications This section describes the pre installed utilities that come with the computer and details how to start them For further information on their operation you may refer to each utility s online manual help files or README TXT file if applicable User s Manual TOSHIBA HWSetup TOSHIBA Peak Shift Control TOSHIBA PC Diagnostic Tool This utility allows you to customize your hardware settings according to the way you work with the computer and the peripherals you use TOSHIBA Peak Shift Control is a function that can help reduce power usage during periods of peak demand by shifting some power consumption to periods when demand is lower For instance in peak hours of power consumption such as in the daytime in the summer the power consumed from the AC power source is automatically stopped and the battery is used for PC op
117. o the computer or subject it to any form of strong impact as this can damage the computer s components or otherwise cause it to malfunction Cleaning the computer To help ensure long trouble free operation keep the computer free of dust and dirt and use care with all liquids around it Be careful not to spill liquids into the computer If the computer does get wet turn the power off immediately and let the computer dry completely In these circumstances you should get the computer inspected by an authorized service provider in order to assess the scope of any damage H Clean the plastics of the computer using a cloth slightly dampened with water You can clean the display screen by spraying a small amount of glass cleaner onto a soft clean cloth and then wiping the screen gently with the cloth Never spray cleaner directly onto the computer or let liquid run into any part of it Never use harsh or caustic chemical products to clean the computer Moving the computer While the computer is designed for flexible day to day usage you should exercise a few simple precautions when moving it in order to help ensure trouble free operation User s Manual 1 16 Make sure all disk disc activity has ended before moving the computer Turn off shut down the computer Disconnect the AC adaptor and all peripherals before moving the computer Close the display panel Do not pick up the computer by its display panel Before ca
118. ode you must set the resolution of the internal display panel to match the resolution of the external display device FN F6 Decreases the brightness of the display panel in individual steps FN F7 Increases the brightness of the display panel in individual steps FN F8 Switches the active wireless devices FN F9 Enables or disables the Touch Pad FN F10 Turns on Arrow Mode User s Manual Key Combination Function FN F11 Turns on Numeric Mode FN F12 Locks the cursor on a specific line FN ESC Turns the sound on or off FN Space Changes the display resolution FN 1 Reduces the icon size on the desktop or the font sizes within one of the supported application windows FN 2 Enlarges the icon size on the desktop or the font sizes within one of the supported application windows FN 3 Decreases the volume of the computer FN 4 Increases the volume of the computer FN 5 Switches between available cooling methods for the current power plan This function is supported with some models FN Z 5 Toggles the mode of the keyboard backlight between Timer On and Off To set up the brightness click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HWSetup Click Keyboard tab and select a level under Keyboard Backlight Brightness Control To set up the timer launch the BIOS setup utility select Power Management gt Keyboard Backlight Control Mode and select TIME
119. ome functions associated with a specific device might not operate properly Before removing a USB device from the USB port of your computer click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and then select the USB device that you want to remove Keep foreign metal objects such as screws staples and paper clips out of the USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury ays Headphone A 3 5 mm mini headphone microphone jack Microphone jack enables connection of a monaural microphone or a stereo headphone SC Smart Card slot This slot allows you to install a Smart Card device Some models are equipped with a Smart Card slot Right side Z30 B The following figures show the right side of the computer Figure 3 3 The right side of the computer Z30 B lt T aaa s gt g lt e amp aoc 1 Memory media slot 4 LAN jack 2 SIM card slot 5 Security lock slot 3 Universal Serial Bus USB 3 0 ports Provided with some models Product appearance depends on the model you purchased sz Memory media slot This slot lets you insert an SD SDHC SDXC memory card minisD microSD Card and MultiMediaCard Refer to the Memory media section for more information Keep foreign metal objects such as screws staples and paper clips out of the Memory media slot Foreign
120. on In this case please try one or more of the following methods E Turn OFF the computer while external devices are connected H Connect external devices after turning OFF of the computer If this function cannot be still used change the setting to disable the function and stop using this function If Sleep and Charge function is enabled the computer s battery discharges during hibernation or when the computer is turned off Connect the AC adaptor to the computer or disable the Sleep and Charge function Problem External devices connected to the compatible ports do not work when connected to a compatible port The USB Wakeup function does not work Sound system User s Manual Procedure Some external devices might not work when connected to a compatible port if the Sleep and Charge function is enabled Reconnect the external device after turning the computer ON If the external device still does not work connect device to an USB port that does not have the Sleep and Charge function or change to disable the Sleep and Charge function When System ON CDP Charge Mode or USB Sleep and Charge function is enabled the USB WakeUp function does not work for ports that support the Sleep and Charge function In that case use an USB port that does not have the USB Sleep and Charge function or change to disable both System ON CDP Charge Mode and USB Sleep and Charge function In addition to the
121. on the model you purchased a Do not plug unplug an HDMI device under the following conditions 1 m The system is starting up E The system is shutting down When you connect a television or external monitor to the HDMI port the display output device is set to HDMI When you unplug the HDMI cable and replug it wait at least 5 seconds before you replug the HDMI cable again Settings for display video on HDMI To view video on the HDMI display device be sure to configure the following settings otherwise you might find that nothing is displayed 7 Be sure to use the function key to select the display device before starting J to play video Do not change the display device or audio device while playing media files Do not change the display device under the following conditions E While data is being read or written E While communication is being carried out Selecting HD Format To select the display mode do the following 1 Click Start gt Control Panel gt Appearance and Personalization gt Display gt Change display settings gt Advanced settings gt List All Modes 2 Select one of the modes at List All Modes Changing the external playback settings After one or more external displays are connected the operating system can automatically detect identify and set up the display settings User s Manual 4 26 I You can also manually manage how the external displays work and change the display settings by
122. on this Bluetooth Stack 2 Multi user considerations The use of Bluetooth is not supported in a multi user environment This means that when you use Bluetooth other users that are logged into the same computer will not be able to use this type of functionality Product Support The latest information regarding operating system support language support or available upgrades can be found on our web site http www toshiba europe com computers tnt bluetooth htm in Europe or www pcsupport toshiba com in the United States Radio Regulatory Information The Wireless device must be installed and used in strict accordance with the manufacturer s instructions as described in the user documentation that comes with the product This product complies with the following radio frequency and safety standards User s Manual 7 8 Europe Restrictions for Use of 2400 0 2483 5MHz Frequencies in Europe France Italy Luxembourg Norway Russian Federation Outdoor use limited to 10mW e i r p within the band 2454 2483 5MHz Implemented Implemented Military Radiolocation use Refarming of the 2 4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012 For private use a general authorization is required if WAS RLAN s are used outside own premises For public use a general authorization is required General authorization required for network and service suppl
123. ou enter the password incorrectly three times in a row or if you do not enter the password within 1 minute the computer shuts off In this case some features that can power on the computer automatically Wake up on LAN Task Scheduler etc might not work You must turn the computer back on to retry password entry TOSHIBA HWSetup T User s Manual TOSHIBA HWSetup is the TOSHIBA configuration management tool available through the Windows operating system To run TOSHIBA HWSetup click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HWSetup The TOSHIBA HWSetup window contains a number of tabs to allow specific functions of the computer to be configured In addition there are also three buttons OK Cancel and Apply OK Accepts your changes and closes the TOSHIBA HWSetup window Cancel Closes the window without accepting your changes Apply Accepts all your changes without closing the TOSHIBA HWSetup window Some options shown in grey are possible to confirm their status TOSHIBA HWSetup screen might have the following tabs E General Allows you to view the current BIOS version or change certain settings back to their default values gm CPU Allows you to set conditions for the CPU m Display Allows you to select the internal LCD and or external monitor when the computer boots up H Boot Setting Allows you to change the sequence in which your computer searches the drives for the operati
124. ou first launch the Realtek HD Audio Manager you can see two device tabs Speakers is the default output device Microphone is the default input device To change the default device click the Set Default Device button under the chosen device tab Information Click the Information button to view hardware information software information and language setting Power Management The audio controller in your computer can be turned off when the audio function is not used To adjust the configuration of audio power management click the Power Management button m When audio power management is enabled the circle button at the upper left of the Power Management is blue and convex E When audio power management is disabled the button is black and concave Speaker Configuration Click the Auto Test button gt to confirm the internal speakers or the headphone sound is coming from the right direction Default Format You can change the sample rate and bit depth of sound Headphone Microphone selection To change the type of headphone or microphone do the following 1 Plug a headphone or microphone into the headphone microphone combo jack 4 31 2 Double click on the circle button in the right side of the Realtek HD Audio Manager main screen 3 Select one from the device list for the device you plugged into Video mode 1 User s Manual Video mode settings are configured via the Screen Resolution dialog T
125. ou purchased Stereo speakers The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system User s Manual 3 1 my p Y DC IN Battery indicator Power indicator Internal storage drive indicator Wireless communication indicator Wireless WAN WiMAX indicator Left side Z30 B User s Manual The DC IN Battery indicator shows the condition of the DC IN and the battery charge status White indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor Refer to the Power Condition Descriptions section for more information on this feature The Power indicator normally glows white when the computer is turned on However if you turn off the computer into Sleep Mode this indicator flashes amber The Internal storage drive indicator blinks white whenever the computer is accessing the internal storage drive The Wireless communication indicator glows white when the wireless functions are turned on Some models are equipped with wireless functions The Wireless WAN WiMAX indicator glows blue when the Wireless WAN WiMAX functions are turned on For some models the indicator blinks to indicate the connection status of the Wireless WAN WiMAX function Some models are equipped with the Wireless WAN WiMAX function The following figures show the left side of the computer
126. pplicable Dedicated Video Memory System Video Memory and Shared System Memory Shared System Memory varies depending on system memory size and other factors Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach might vary depending on surrounding electromagnetic environment obstacles access point design and configuration and client design and software hardware configurations The actual transmission speed is lower than the theoretical maximum speed Copy Protection Applicable copy protection standards included in certain media might prevent or limit recording or viewing of the media Glossary The terms in this glossary cover topics related to this manual Alternate naming is included for reference User s Manual 7 20 User s Manual Abbreviations AC AMT ASCII BIOS BD ROM bps CD CD ROM CD RW CMOS CPU DC DDR DIMM DVD DVD R DVD RAM DVD R DL DVD ROM DVD RW DVD R DL FAT FCC FHD GB GBps HD HD HDD HDMI HDMI CEC HTML Alternating Current Intel Active Management Technology American Standard Code for Information Interchange Basic Input output System Blu ray Disc Read only Memory bits per second Compact Disc Compact Disc Read only Memory Compact Disc rewritable Complementary Metal oxide Semiconductor Central Processing Unit Direct Current Double Data Rate Dual Inline Memory Module D
127. pressing P while holding down the Windows H key If you disconnect the external display before you turn off the computer s power be sure to switch to the internal display When you change the display output device the audio playback device might not switch automatically In this case to set the playback device to the same device as the display output device adjust the audio playback device manually by the following steps 1 Click Start gt Control Panel gt Hardware and Sound gt Sound 2 Inthe Playback tab select the playback device which you want to switch to 3 To use the internal speakers on your computer select Speakers To use the television or the external monitor that you have connected to the computer select a different playback device 4 Click the Set Default button 5 Click OK to close the Sound dialog TOSHIBA Hi Speed Port Replicator Ill 180W 120W User s Manual In addition to the ports available on the computer the TOSHIBA Hi Speed Port Replicator III 180W 120W also provides several kinds of ports The Port Replicator connects directly to the docking interface on the underside of the computer The AC adaptor connects the Port Replicator to a power source H You must connect the AC adaptor before you connect to a Port Replicator E When your computer is docked in the Port Replicator the following ports on the computer if present are not operational m LAN jack HDMI out port m External
128. r fingerprints due to insufficient unique characteristics in their fingerprints m The recognition success rate might differ from user to user Set up Fingerprint Registration i User s Manual Use the following procedure when first using fingerprint authentication E n use the fingerprint authentication system uses the same username and password as defined within the Windows operating system If no Windows password has been configured you must do this before starting the fingerprint registration process This sensor has the memory space for at least twenty fingerprint patterns You might be able to register more fingerprint patterns depending on the sensor memory usage 1 Click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Fingerprint Utility 2 The Enroll screen is displayed Enter the current account password into the Windows Password field If no Windows password has been configured you will be asked to configure the new logon password Then click Next Click the non enrolled finger you want to register and then click Next 4 The instructions for enrollment operation screen is displayed Carefully read them and then click Next 5 The scanning practice screen is displayed You are able to practice swiping three times your finger to ensure you use the correct method When you have finished practicing swiping your finger click Next 6 Swipe four times with the same finger If scanning
129. rd Start refers to the button in Windows 7 Click E Tap the Touch Pad or click the left Touch Pad control button once Left click the mouse once m Tap the touch screen once only for touch screen models User s Manual 2 1 Right click E Double click E Tap the Touch Pad with two fingers together or click the right Touch Pad control button once Right click the mouse once Press and hold on the touch screen only for touch screen models Tap the Touch Pad or click the left Touch Pad control button twice Left click the mouse twice Tap the touch screen twice only for touch screen models Internal Storage Drive Your computer is equipped with one of the following storage devices HDD Hard Disk Drive SSD Solid State Drive In this manual the word internal storage drive refers to either HDD or SSD unless otherwise stated Short model name Model name of your computer is shortened and referred to as the following in this manual LCD Full Model Name Short Model Name 33 8cm PORT G Z30 B Z30t B Satellite Z30 B Z30t B Z30 B 13 3 35 6cm TECRA Z40 B Z40t B Satellite Z40 B Z40t B Z40 B 14 0 Using your computer for the first time i User s Manual Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer It is intended to help you be more comfortable and productive while using the notebook comp
130. region your computer is configured for with keyboards being available for numerous languages There are different types of keys specifically typewriter keys function keys soft keys Windows special keys and the keypad overlay AN Never remove the key caps on your keyboard Failure to do so might damage the parts under the key caps Keyboard indicator The following figure shows the position of the CAPS LOCK indicator When the CAPS LOCK indicator glows the keyboard produces capitals when any letter is typed User s Manual 4 2 Figure 4 1 CAPS LOCK indicator 1 CAPS LOCK indicator Product appearance depends on the model you purchased CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format Function Key User s Manual The function keys F1 F12 are the 12 keys at the top of your keyboard FT fF F Fe E n i u a F1 E a Function keys let you enable or disable certain features of the computer The functions can be performed by pressing the associated function keys F3 E F5 E Key Combination Function FN F1 Enters Lock computer mode To restore your desktop you need to log on again FN F2 Switches between the power plans FN F3 Switches the system to Sleep Mode FN F4 Switches the system to Hibernation Mode FN F5 Changes the active display device To use a simultaneous m
131. rrying your computer shut it down disconnect the AC adaptor and allow it to cool down A failure to follow this instruction might result in minor heat injury Do not expose the computer to rapid temperature changes for example in a situation where you carry the computer from a cold environment to a warm room Do not turn on the power until condensation disappears Be careful not to subject the computer to impact or shock A failure to follow this instruction could result in damage to computer computer failure or loss of data Never transport your computer with any cards installed This might damage either the computer and or the card resulting in computer failure Always use a suitable carry case when transporting the computer When carrying your computer be sure to hold it securely so that it does not fall or hit anything Do not carry your computer by holding any of its protruding elements Mobile phones Be aware that the use of mobile phones can interfere with the audio system The operation of the computer will not be impaired in any way but it is recommended that a minimum distance of 30 cm is maintained between the computer and a mobile phone that is in use Instruction Manual for Safety and Comfort All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort Be sure to read it before using the computer Safety Icons Safety icons are used
132. rst time ccccesseseeeeeesseeeeseeeneeneeens 2 2 Turning off the pOWer cs cccceeeeeee cece ceeeeee eee ee ee neeeeeeeeeeeeeaneeeseeeeeeaees 2 7 The Grand Tour The Grand Tour for Z30 B 2 cccccccceeceeeeeeeeeeeeeeeseeeeeeeeeseseseeeeeeeeeeeeeeees 3 1 The Grand Tour for Z40 B ccccecssecceeeeeeeeeeeeeeeeeneeeeeeeneeeeeeeeeeeeeeeeeee 3 11 Internal Hardware Components s scsecseecseceeeeeeeeeeseneneneneneeees 3 20 Power Condition Descriptions eccceseseeeeeeseeeeeeseeeneeeesesseeeeeens 3 23 Operating Basics Using the Touch Screen u eeccseeeeeeeneeeeseeeeeseeeeeseeeeeeeeesesseeeeeseenensseeees 4 1 Using the Touch Pad eccccesesesseeeeeseneeeeseeseeseeeeeseeneeeseeeeaseeeeeseeneneeeeees 4 1 Fhe HOY DOAN ieia inoa aaa Sev daicadi acaginecee neice cecvand aa andada A 4 2 Using the ACCUPOINE sissisodan Nese eee eee eed 4 5 Using the Fingerprint Sensor cceeseeenseeeeeeeeeeeeeeeeseeseeeeeeeeneeeeeeens 4 6 Battery onenean aeaaeai anaana sees ates iaa aaua sunset ccs daaa aaa aiaa 4 12 Wireless WAN Device c ceccccssteeeeseeeseeeeenneeeeseseeneneseeeeneeeesessenenenees 4 16 GPS Function ssaasssssessseenneennnrnnnnrnnnnennnrennnnnnnnennnnennnnnnnnnnnnnennnnnnnn nennen nnne 4 17 LAN A 4 18 Memory m dia sasssa daare daana daaa aidaa dda fanaa adia idana ddai 4 19 Smart Card DEEE 4 23 External Display missini alee nda 4 24 TOSHIBA Hi Speed Port Replicator II 18O0
133. rts a maximum of two external displays For each VIDEO panel only one port can function at a time 4 28 Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft The computer has a security lock slot into which you can attach one end of the security cable while the other end attaches to a desk or similar object The methods used for attaching security cables differ from product to product Refer to the instructions for the product you are using for more information Connecting the security lock To connect a security cable to the computer do the following 1 Turn the computer so the security lock slot faces you 2 Align the security cable with the lock slot and secure it in place Figure 4 14 Security lock Z30 B 1 Security lock slot 2 Security lock Product appearance depends on the model you purchased Optional TOSHIBA Accessories To make your computer even more powerful and convenient to use you can add a number of options and accessories For reference the following list details some of the items that are available from your reseller or TOSHIBA dealer Universal AC Adaptor If you frequently use your computer at more than one site it might be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to carry the adaptor with you always TOSHIBA Hi Speed TOSHIBA Hi Speed Por
134. s risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux Les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c a d qu ils ont la priorit pour les bandes 5 25 5 35GHz et 5 65 5 85GHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met USA Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Refer to the FCC information section for the detailed information This device and its antenna s must not be co located or operating in conjunction with any other antenna or transmitter The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits Nevertheless the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health User s Manual Canada limits for the
135. s tab select the sound effects you would like and click Apply DTS Studio Sound User s Manual DTS Studio Sound is a premium audio enhancement suite that utilizes revolutionary audio technology to provide the most immersive and realistic listening experience ever offered for a two speaker playback environment DTS Studio Sound is provided with some models It provides the following features E Advanced audio rendering to match 2D and 3D video content for enveloping surround sound E Accurate placement of audio cues for immersive surround sound from any PC speaker configuration laptop desktop speakers or headphones E Broad sweet spot with elevated sound image m Maximum volume output delivering maximum volume without creating clipping or distortion 4 30 Dialog enhancement for clear and intelligible vocals Bass enhancement for rich low frequency production High frequency definition for crisp details H Consistent volume level across content To access the utility click Start gt All Programs gt DTS Inc gt DTS Studio Sound U S patents apply to this product See http patents dts com Manufactured under license from DTS Licensing Limited Realtek HD Audio Manager User s Manual You can confirm and change the audio configuration using the Realtek HD Audio Manager To launch the Realtek HD Audio Manager Click Start gt Control Panel gt Hardware and Sound gt Realtek HD Audio Manager When y
136. se situations might for example include H Using the wireless products equipment on board of airplanes or E In any other environment where the risk of interference to other devices or services is perceived or identified as harmful If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment for example airports you are encouraged to ask for authorization to use the wireless device prior to turning on the equipment Wireless LAN Technology A User s Manual The wireless communication function of the computer supports some wireless communication devices Only some models are equipped with both Wireless LAN and Bluetooth functions amp Do not use the Wireless LAN Wi Fi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields Interference from a microwave oven or other source can disrupt Wi Fi or Bluetooth operation User s Manual E Turn off all wireless functionalities when near a person who might have a cardiac pacemaker implant or other medical electric device Radio waves might affect pacemaker or medical device operation possibly resulting in serious injury Follow the instruction for your medical device when using any wireless functionality Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors Radio wav
137. se the up and down cursor key to select the appropriate option from the menu according to your actual recovery media 5 A menu will be displayed from which you should follow the on screen instructions If you have previously chosen to remove the recovery partition and are trying to create Recovery Media the following message appears The Recovery Media Creator can not be launched because there is no recovery partition When there is no recovery partition the Recovery Media Creator cannot make Recovery Media However if you have already created a Recovery Media you can use it to restore the recovery partition If you have not created Recovery Media contact TOSHIBA support for assistance Restoring the pre installed software from the Recovery Partition A i User s Manual A portion of the internal storage drive space is configured as a hidden recovery partition This partition stores files which can be used to restore pre installed software in the event of a problem If you set up your internal storage drive again later do not change delete or add partitions in a manner other than specified in the manual otherwise you might find that space for the required software is not available In addition if you use a third party partitioning program to reconfigure the partitions on your internal storage drive you might find that it becomes impossible to set up your computer When you reinstall the Windows operating s
138. ss WAN WiMAX function Some models are equipped with the Wireless WAN WiMAX function Left side Z40 B The following figures show the left side of the computer Figure 3 8 The left side of the computer Z40 B SF Hom g s gt 1 Cooling vents 4 HDMI out port 2 External RGB monitor port 5 SIM card slot 3 Universal Serial Bus USB 3 0 port 6 Memory media slot Provided with some models Product appearance depends on the model you purchased Cooling vents The cooling vents help the processor to avoid overheating External RGB monitor This port provides 15 pin analog RGB port port Refer to the External RGB monitor port pin assignment section for information on external RGB monitor port pin assignment This port allows you to connect an external RGB monitor to the computer User s Manual 3 12 Homi Ss A User s Manual Universal Serial Bus USB 3 0 port One Universal Serial Bus port which complies to the USB 3 0 standard is provided on the left side of the computer The USB 3 0 port is compliant with USB 3 0 standard and backward compatible with USB 2 0 devices USB 3 0 port s might work as USB 2 0 port s when operating in USB Legacy Emulation mode Note that it is not possible to confirm the operation of all functions of all USB devices that are available Some functions associated with a specific device might not operate properly Before removing a USB d
139. ssure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health For more detailed information about the collection and recycling programmes available in your country please visit our website www toshiba eu recycling or contact your local council office or the retail outlet where you purchased the product A Disposal of batteries and or accumulators The crossed out wheeled dust bin symbol indicates that batteries and or accumulators must be collected and disposed of separately from household waste POME GA If the battery or accumulator contains more than the specified values of lead Pb mercury Hg and or cadmium Cd defined in the European Battery Directive then the chemical symbols for lead Pb mercury Hg and or cadmium Cd will appear below the crossed out wheeled dust bin symbol By participating in the separate collection of batteries you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health To achieve this you should take any battery and or accumulator to your local recycling site or to a retail outlet or facility that offers to collect these devices for environmentally friendly disposal ensuring that the terminal contacts are covered by non conductive tape For more detailed information about the collection and recycling
140. sted to the point that computer operation cannot be continued the system automatically enters Hibernation Mode and shuts itself down This can be specified in the Power Options If you have to interrupt your work you can use this feature to allow you to turn off power to the computer without exiting from your software Data is maintained in the computer s main memory so that when you next turn on the power you can continue working right where you left off Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software The contents of main memory are automatically saved to the Solid State Drive so that when you next turn the power on again you can continue working right where you left off Refer to the Turning off the power section for more details USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports Please note that the USB port on the keyboard dock does not support this function For example if a mouse or USB keyboard is connected clicking the mouse button or pressing the keyboard will wakeup the computer Heat dispersal To protect against overheating the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer s internal temperature rises to a certain level You are able to select whether to control this temperature
141. t Replicator III 180W Port Replicator Ill 120W provides several kinds of ports Refer to 180W 120W the Port Replicators User s Manual for more details Sound System and Video mode This section describes some of the audio control functions User s Manual 4 29 Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows H To launch the Volume Mixer utility right click on the speaker icon on the Windows Taskbar and then select Open Volume Mixer from the sub menu m To adjust the volume level of speakers or headphones move the Speakers slider m To adjust the volume level of an application that you are using move the slider for the corresponding application Microphone Level To change the microphone recording level do the following 1 Right click on the speaker icon on the Windows Taskbar and select Recording devices from the sub menu 2 Select Microphone and click Properties 3 On the Levels tab move the Microphone slider to increase or decrease the microphone volume level If you feel the microphone volume level is inadequate move the Microphone Boost slider to a higher level Audio Enhancements To apply the sound effects for your current speaker do the following 1 Right click on the Speakers icon on the Windows Taskbar and then select Playback devices from the sub menu 2 Select Speakers and click Properties 3 On the Enhancement
142. t happen User s Manual 4 17 LAN i LAN User s Manual Your current location might not be shown depending on the status of GPS or the location If you are obtaining your current location information from the computer your current location might not be detected due to the information accuracy Specifically your current location might not be detected in the following places or situations E Inside or directly under a building Inside a bag or box Among dense trees When there is an obstacle person or object in the front of the antenna Underground tunnel underground or underwater Buildings streets or residential areas Near to high voltage cables Bad weather such as heavy rain or snow The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T This section describes how to connect disconnect to a LAN m The Wake up on LAN function consumes power even when the system is off Leave the AC adaptor connected while using this feature E The Link speed 10 100 1000 megabits per second changes automatically depending on the network conditions connected device cable or noise and so on cable types The computer must be configured properly before connecting to a LAN Logging onto a LAN using the computer s default settings might cause a malfunction in LAN operation
143. t interfere with any of the equipment listed above 2 If this equipment causes RF interference to other radio stations promptly change the frequency being used change the location of use or turn off the source of emissions 3 Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations 2 Indication for Wireless LAN The indication shown below appears on this equipment 1 2 34 I I 2 4 This equipment uses a frequency of 2 4GHz DS This equipment uses DS SS modulation OF This equipment uses OFDM modulation 4 The interference range of this equipment is less than 40m This equipment uses a frequency bandwidth from 2 400MHz to 2 483 5MHz It is possible to avoid the band of mobile object identification systems arkwn gt s gt 3 Indication for Bluetooth The indication shown below appears on this equipment PONS 2 4 This equipment uses a frequency of 2 4 GHz FH This equipment uses FH SS modulation 1 The interference range of this equipment is less than 10m This equipment uses a frequency bandwidth from 2 400 MHz to 2 483 5 MHz It is impossible to avoid the band of mobile object identification systems 4 About the JEITA 5GHz Wireless LAN supports W52 W53 W56 Channel IEEE802 11b g n IEEE802 11a n w56 Device Authorization User s Manual This device obtains the Technical Regulation Conformity Certifica
144. t it If you insert the media in wrong direction you might not be able to remove it When inserting the memory media do not touch the metal contacts You might expose the storage area to static electricity which can destroy data Do not turn off the computer or switch to Sleep Mode or Hibernation Mode while files are being copied Failure to do so might cause data loss Removing memory media A User s Manual The following instructions apply to all types of supported media devices To remove memory media do the following 1 E VN Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar Select memory media Push the memory media until you hear a click to partially release it Grasp the media and remove it If you remove the memory media or turn off the power while the computer is accessing the memory media you might lose data or damage the media 4 22 Donot remove the memory media while the computer is in Sleep or Hibernation Mode The computer might become unstable or data in the memory media might be lost Do not remove only the miniSD microSD Card while leaving the adaptor in the memory media slot Smart Card i A Smart Card is a credit card sized plastic card An extremely thin integrated circuit IC chip is embedded into the card on which information can be recorded These cards can be used for a wide variety of applications including telephone related and electronic monetary p
145. t of Video RAM available depends on the system memory of the computer Click Start gt Control Panel gt Appearance and Personalization gt Display gt Adjust resolution The amount of Video RAM can be verified by clicking the Advanced settings button in the Screen Resolution window Graphics Processing Graphics Processing Unit GPU performance Unit might vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized when operating in AC power mode and might decrease considerably when operating in battery power mode Legal Footnote Graphics Processing Unit GPU For more information regarding Graphics Processing Unit GPU refer to the Legal Footnotes section NVIDIA Graphic Control User s Manual Some NVIDIA graphics models might include NVIDIA Optimus technology feature NVIDIA Optimus technology intelligently optimizes notebook performance by seamlessly switching between a discrete NVIDIA GPU for great graphics performance and an Intel integrated graphics chip for sustained battery life Switching is automatic and does not require the user to reboot the computer In the Manage 3D Settings menu of NVIDIA Control Panel you can change the global 3D settings and create overrides for specific programs The overrides will be used automatically each time the specified programs are launched 3 21 Use the default set
146. t resource for current information and support TOSHIBA technical support If you are still unable to solve the problem and suspect that it is hardware related visit TOSHIBA technical support website http www toshiba co jp worldwide User s Manual 6 14 Chapter 7 Appendix Specifications This section summarizes the technical specifications of the computer Physical Dimensions The following physical dimensions do not include parts that extend beyond the main body The physical dimensions might vary depending on the model you purchased Z30 B 316 w x 227 d x 13 9 17 9 h millimeters 316 w x 227 d x 15 9 19 9 h millimeters touch screen models Z40 B 338 w x 236 d x 20 4 h millimeters 338 w x 236 d x 21 9 h millimeters touch screen models Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C 41 F to 35 C 20 to 80 95 F noncondensing Non operating 20 C 4 F to 60 C 10 to 90 140 F noncondensing Wet bulb temperature 29 C maximum Conditions Altitude from sea level Operating 60 to 3 000 meters Non operating 60 to 10 000 meters maximum User s Manual 7 1 Power Requirements AC adaptor 100 240V AC 50 Hz or 60 Hz cycles per second Computer 19V DC External RGB monitor port pin assignment o 6 Pin Signal Name Description 1 0 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reser
147. the use of the panel power off feature Executing Sleep Mode You can enter Sleep Mode in one of following ways Click Start Point to the arrow jg beside the Shut down button and then select Sleep Close the display panel Note that this feature must be enabled within the Power Options Press the power button Note that this feature must be enabled within the Power Options When you turn the power back on you can continue where you left off when you shut down the computer When the computer is in Sleep Mode the Power indicator blinks amber If you are operating the computer on battery power you can lengthen the overall operating time by turning it off into Hibernation Mode Sleep Mode consumes more power while the computer is off Sleep Mode limitations Sleep Mode will not function under the following conditions Power is turned back on immediately after shutting down Memory circuits are exposed to static electricity or electrical noise The battery power is exhausted and the AC Adaptor is not connected 2 9 Hibernation Mode A User s Manual The Hibernation Mode feature saves the contents of memory to the internal storage drive when the computer is turned off so that the next time it is turned on the previous state is restored Note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer m Save your data While entering Hibernation Mode the computer sa
148. time are lost TOSHIBA Setup Utility by using the following steps 1 Launch the TOSHIBA Setup Utility Refer to the TOSHIBA Setup Utility section for further information 2 Set the date in the System Date field Set the time in the System Time field 4 Follow the on screen instructions to proceed o Keyboard Keyboard problems can be caused by the setup and configuration of the computer Refer to the The Keyboard section for further information Problem Procedure Output to screen is Refer to your software documentation to ensure garbled that it is not remapping the keyboard in any way remapping involves changing or reassigning the function of each key If you are still unable to use the keyboard you should contact TOSHIBA Support Internal display panel User s Manual Apparent problems of the computer s display panel might be related to setup and configuration of the computer Problem Procedure No display Press the function keys to adjust the display priority and to make sure that it is not set for output to an external monitor Markings appearon These marks might have come from contact with the computer s the keyboard and Touch Pad while the display display panel panel has been closed Try to remove the marks by gently wiping the display panel with a clean dry cloth or if this fails with a good quality LCD screen cleaner In this latter instance you should always follow the instructions with the screen
149. ting for NVIDIA Optimus technology If the program does not run normally after the setting has been changed restore the program to the default setting E Ifthe program does not run normally restore the Preferred graphics processor to the default setting m When you use some video playback programs to play video files the preferred graphics processor in the Program Settings tab cannot be changed to the graphics other than Integrated Graphics To access the Program Settings click NVIDIA Control Panel gt Manage 3D settings gt Program Settings To launch the NVIDIA Control Panel Click Start gt Control Panel gt Hardware and Sound gt NVIDIA Control Panel For more information about the NVIDIA Control Panel system refer to the NVIDIA Control Panel Help To access it click Help from the main menu and then select NVIDIA Control Panel Help On Optimus models two kinds of Display Drivers are installed Intel HD Graphics Driver and NVIDIA Graphics Driver XXX XX Do not uninstall the display driver from Uninstall Program in the Control Panel To uninstall the display driver 1 Uninstall NVIDIA Graphics Driver XXX XX 2 Then uninstall Intel HD Graphics Driver Intel Display Power Saving Technology User s Manual Intel GPU models might include the Display Power Saving Technology feature that can save the power consumption of the computer by optimizing picture contrast on the
150. tion and it belongs to the device class of radio equipment of low power data communication system radio station stipulated in the Telecommunications Business Law of Japan Intel Dual band Wireless AC 7265 Intel Dual band Wireless N 7265 Intel Wireless N 7265 The Name of the radio equipment 7265NGW DSP Research Inc Approval Number D140017003 Intel Dual band Wireless AC 3160 The Name of the radio equipment 3160NGW DSP Research Inc Approval Number D130092003 The following restrictions apply Do not disassemble or modify the device Do not install the embedded wireless module into other device Radio approvals for wireless devices A This equipment is approved to the radio standard by the countries regions in the following table If you use this equipment in the countries regions which are not listed in the following table contact TOSHIBA Support As of December 2014 Austria Belgium Bulgaria Canada Cyprus Czech Rep Denmark Estonia Finland France Germany Greece Hong Kong Hungary Iceland India Ireland Italy Japan Korea Latvia Liechtenstein Lithuania Luxemburg Malta Monaco Netherlands Norway Philippines Poland Portugal Romania Slovak Republic Slovenia Spain Sweden Switzerland UK USA Information about Intel AMT Your computer might support Intel Active Management Technology AMT depending on the model you purchased Using built in platform capabilities and popular third party management and security
151. tion and the documentation supplied with your mouse User s Manual Touch Pad Problem The Touch Pad does not work On screen pointer does not respond to pointing device operation Double tapping Touch Pad does not work The on screen pointer moves too fast or too slow The reaction of Touch Pad is either too sensitive or not sensitive enough Procedure Check the Device Select settings by the following steps 1 Click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Inthe Advanced tab click Advanced feature settings gt Device Select In this instance the system might be busy Try moving the mouse again after waiting a short while In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK Adjust the touch sensitivity To access this utility click Start gt Control Panel gt
152. tions show the plug shapes for the U S A and Canada the United Kingdom Australia Europe and China USA United Kingdom UL approved BS approved Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability T User s Manual The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum DSSS Orthogonal Frequency Division Multiplexing OFDM radio technology and is compliant to E The IEEE 802 11 Standard on Wireless LANs Revision a b g n b g n or Revision a b g n ac as defined and approved by the Institute of Electrical and Electronics Engineers Bluetooth Modules are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum FHSS radio technology and is compliant to H Bluetooth Specification depending on the model you purchased as defined and approved by the Bluetooth Special Interest Group E Logo certification with Bluetooth wireless technology as defined by the Bluetooth Special interest Group This Bluetooth product is not compatible with devices using Bluetooth Version 1 0B specifications The wireless devices have not completed verification of connection and operation with all devices which are using the Wireless LAN or Bluetooth radio technology Bluetooth a
153. u place your finger on the sensor whether for fingerprint enrollment registration or recognition Wash and dry your hands thoroughly Remove static electricity from your fingers by touching any metal surface Static electricity is a common cause of sensor failures especially when the weather is dry Clean the sensor with a lint free cloth Do not use detergent or any other chemicals to clean the sensor Avoid the following finger conditions for enrollment or recognition as they might result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate m Soaked or swollen finger for example as might occur after taking a bath Injured finger Wet finger Soiled or oily finger m Extremely dry skin condition on finger Observe the following to improve the fingerprint recognition success rate Enroll two or more fingers Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers Check the condition of your finger Any conditions which have changed since enrollment such as injury rough skin and extremely dry wet soiled dirty oily soaked or swollen fingers might lower the recognition success rate Also if the fingerprint is worn down or the finger becomes thinner or fatter the recognition success rate might be lowered As the fingerprint for each finger is different and unique you should ensure that only the registered or enrolled fingerprint or fingerprints are
154. uency devices Article 14 The low power radio frequency devices shall not influence aircraft security and interfere legal communications If found the user shall cease operating immediately until no interference is achieved The said legal communications means radio communications is operated in compliance with the Telecommunications Act The low power radio frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices User s Manual Australia and New Zealand regulatory compliance This equipment incorporates a radio transmitting device in normal use a separation distance of 20cm will ensure radio frequency exposure levels complies with the Australian and New Zealand Standards Using this equipment in Japan In Japan the frequency bandwidth of 2 400MHz to 2 483 5MHz for second generation low power data communication systems such as this equipment overlaps that of mobile object identification systems premises radio station and specified low power radio station 1 Important notice The frequency bandwidth of this equipment may operate within the same range as industrial devices scientific devices medical devices microwave ovens licensed radio stations and non licensed specified low power radio stations for mobile object identification systems RFID used in factory production lines Other Radio Stations 1 Before using this equipment ensure that it does no
155. umber 0 1 9 Must contain a mix of lower case a b z etc and upper case A B Z etc letter Must contain at least one special character of the following A amp lt gt Underscore _ is considered the same as Roman alphabet characters and is not counted as a special character Key input is based on the US keyboard layout The following table shows examples of the special characters in US keyboard layout oOo Bw Special character you Corresponding number want to input key SHIFT key a number key l 1 2 3 4 5 A 6 amp 7 8 9 0 Select Intel R AMT Configuration and press the Enter key Select Manageability Features Selection and press the Enter key Select Disabled and press the Enter key Press the Y key and press the ESC key i Select MEBx Exit and press Y key When the computer restarts go to BIOS setup utility On the BIOS setup utility screen change AMT Setup Prompt to Disabled Press the F10 key to save the settings and press the Y key When using the computer with the AC adaptor connected and the AMT function set to enabled power might still be supplied to the system memory even when the computer power is turned off or the computer is in Sleep Mode or Hibernation Mode When connecting the AC adaptor the computer is powered and can be turned on If the power is automatically turned off a
156. urable power savings by using it continuously TOSHIBA eco Utility helps control the power consumption of your computer Various information can help you understand your degree of contribution to the environment To access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt eco Utility For details on TOSHIBA eco utility see the help file TOSHIBA HDD SSD This utility includes wizard functions to monitor Alert Utility the internal storage drive operating status and execute the system backup To access the utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt HDD SSD Alert User s Manual 5 2 TOSHIBA Service Station TOSHIBA PC Health Monitor Trusted Platform Module TPM This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs When enabled this application periodically transmits to our servers a limited amount of system information which will be treated in strict accordance with the rules and regulations as well as applicable data protection law To access this utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Service Station The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption battery health and system cooling
157. used for identification Check the position and speed at which you swipe your finger across the sensor Refer to the preceding drawing The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint However there might be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints The recognition success rate might differ from user to user Points to note about Fingerprint Utility User s Manual If Windows file encryption function EFS Encryption File System is used to encrypt a file the file cannot be further encrypted using the encryption function of this software You can back up the fingerprint data or the information registered to Web Site Passwords Use Import Export in TOSHIBA Fingerprint Utility main menu 1 E Also refer to the fingerprint utility Help file for more information by clicking in TOSHIBA Fingerprint Utility main menu Fingerprint utility limitations TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error free or that it will accurately screen out unauthorized users at all times TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software E The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint However there might be instances where certain users are unable to register thei
158. uter By following the recommendations in it you can reduce your chance of developing a painful or disabling injury to your hand arms shoulders or neck This section provides basic information to start using your computer It covers the following topics H Connecting the AC adaptor Opening the display Turning on the power Initial setup Getting to know Windows Use a virus check program and make sure that it is updated regularly Never format storage media without checking its content formatting destroys all stored data It is a good idea to back up the internal storage drive or other main storage device to external media periodically General storage media is not durable or stable over long periods of time and under certain conditions might result in data loss Before you install a device or application save any data in memory to the internal storage drive or other storage media Failure to do so might result in data loss Connecting the AC adaptor User s Manual Attach the AC adaptor when you want to charge the battery or operate from AC power The battery pack must be charged before you can operate from battery power The AC adaptor can automatically adjust to any voltage ranging from 100 volts to 240 volts and to a frequency of either 50 hertz or 60 hertz enabling you to use this computer in almost any country region The adaptor converts AC power to DC power and reduces the voltage supplied to this computer
159. utton AccuPoint AccuPoint control buttons The display hinges allow the display panel to be positioned at a variety of easy to view angles The keyboard contains character keys control keys function keys and special Windows keys providing all the functionality of a full size keyboard Refer to the The Keyboard section for details Press this button to power on off the computer A pointer control device located in the center of the keyboard is used to control the on screen pointer Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the on screen pointer User s Manual XA ay User s Manual Touch Pad ON OFF indicator TOSHIBA eco indicator Touch Pad Touch Pad control buttons Fingerprint Sensor DC IN Battery indicator Power indicator Internal storage drive indicator Double tap this indicator to enable disable the Touch Pad The indicator for some models shows the status of the Touch Pad E Enabled off E Disabled glows white Double tap this indicator to launch the TOSHIBA eco Utility The Touch Pad located in the palm rest is used to control the movement of the on screen pointer To use the Touch Pad simply touch and move your fingertip across it in the direction you want the on screen pointer to go The two buttons located on the bottom of the Touch Pad are used like the buttons on a standard mouse Press t
160. ved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 5V Power Supply 10 GND Ground 11 Reserved Reserved 12 SDA Serial Data Signal VO 13 HSYNC Horizontal Sync Signal O 14 VSYNC Vertical Sync Signal O 15 SCL Serial Clock Signal O I O I Input to computer I O O Output from computer User s Manual 7 2 AC Power Cord and Connectors The AC input plug of the power cord must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Wire size Minimum 0 75 mm Current rating Minimum 2 5 amperes Certification agencies User s Manual China CQC U S and Canada UL listed and CSA certified No 18 AWG Type SVT or SPT 2 Australia AS Japan DENANHO Europe Austria OVE Italy IMQ Belgium CEBEC The Netherlands KEMA Denmark DEMKO Norway NEMKO Finland FIMKO Sweden SEMKO France LCIE Switzerland SEV Germany VDE United Kingdom BSI In Europe two conductors power cord must be VDE type HOSVVH2 F or HO3VVH2 F and for three conductors power cord must be VDE type HOSVV F For the United States and Canada two pin plug configuration must be a 2 15P 250 V or 1 15P 125 V and three pin plug configuration must be 6 15P 250 V or 5 15P 125 V as designated in the U S National Electrical code handbook and the Canadian Electrical Code Part Il The following illustra
161. ves the contents of memory to the internal storage drive However for Safety sake it is best to save your data manually m Data will be lost if you disconnect the AC adaptor before the save is completed To prevent data loss do not switch to Hibernation Mode while transferring data to external media such as USB devices memory media or other external memory devices Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits m Saves data to the internal storage drive when the computer automatically shuts down because of a low battery condition You can return to your previous working environment immediately when you turn on the computer E Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature H Allows the use of the panel power off feature Starting Hibernation Mode To enter Hibernation Mode click Start point to the arrow i beside the Shut down button and then select Hibernate from the menu Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid To define these settings do the following 1 Click Start gt Control Panel gt System and Security gt Power Options 2 Click Choose what the power button does or Choose what closing the lid does 3 Enable the desired Hibernation Mode s
162. wer Disconnect the AC adaptor and turn on the computer s power If it does not turn on then go to Step 4 Operate the computer on battery power for five minutes If you find that the battery pack has at least five minutes of operating time continue operating until the battery pack is fully discharged However if the DC IN Battery indicator flashes or there is some other warning to indicate a low battery condition go to Step 4 Connect the AC adaptor to the DC IN 19V jack of the computer and to a wall outlet that is supplying power The DC IN Battery indicator glows amber to indicate that the battery pack is being charged However if DC IN Battery indicator does not glow this indicates that power is not being supplied Check the connections for the AC adaptor and the power cord Charge the battery pack until the DC IN Battery indicator glows white Wireless WAN Device Some models are equipped with the Wireless WAN device This device gives you the ability for a high speed connection to the Internet corporate intranet and your email while you are away from the office Installing a SIM card To install a SIM card do the following 1 2 3 4 Click Start and then select Shut down Remove the AC adaptor and all cables and peripherals connected to the computer Locate the SIM card slot To pop the SIM card tray partially open insert a slender object about 10mm diameter 0 8mm such as a straightened paper clip into th
163. y This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny Alesund Only for indoor applications Restrictions for Use of 5150 5350MHz Frequencies in Europe Italy Luxembourg User s Manual Implemented For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply Russian Limited Federation e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2 Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m Restrictions for Use of 5470 5725MHz Frequencies in Europe Italy Luxembourg Implemented Russian Limited Federation For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2
164. ystem the internal storage drive will be reformatted and all data will be lost Make sure that the AC adaptor is connected during the restoring process 1 Click Start Point to the arrow ia beside the Shut down button and then select Restart 2 Hold down 0 zero key and then release this key one second after the computer is power on 3 Follow the on screen instructions to finish the recovery User s Manual 5 18 Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability however should problems occur you are able to use the procedures detailed in this chapter to help determine the cause You should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place Problem solving process If you observe the following guidelines resolving problems will be much easier H Stop immediately when you recognize a problem exists as taking further action might result in data loss or damage or you might destroy valuable problem related information that can help solve the problem m Observe what is happening Write down what the system is doing and what actions you performed immediately before the problem occurred Make a screenshot of the current display Also be aware that the questions and procedures described in this chapter are meant only as a guide they are not definitive problem solving techniques In reality many problems can be solved simp

Z40-B, Z40t-B, Z30-B, Z30t-B User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents