Home

Platinum Beam 5R EXTREME User Manual ver 1

image

Contents

1. 9Z s X L SAFETY CABLE ALWAYS USE A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN SUSPENDED ENVIRONMENT TO ENSURE THE FIXTURE WILL NOT DROP IF THE CLAMP FAILS 20 PLATINUM BEAM SR EXTREME User Manual Ver I LATION www elationlighting com CLAMP MOUNTING The fixture provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Brackets x2 and safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamps to the included omega brackets using a M10 screw fitted through the center hole of the Omega Bracket Be sure to attach the included Safety Cable to the fixture using the safety cable rigging point integrated in the base assembly 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener SECURING Regardless of the rigging option you choose for your fixture always be sure fo secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as ilustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 2 PLATINUM BEAM SR EXTREME User Manual Ver I ATION www elationlighting com FIXTURE MENU ON BOARD SYSTEM MENU The fixture comes with an easy to navigate system menu The next section will detail the functi
2. PAN MOVEMENT 8 BIT 0 255 PAN Movernent By 630 540 PAN FINE MOVEMENT 16 BIT 0 255 Fine Control of PAN Movement _ BiT 0 255 TILT Movement By 270 TILT MOVEMENT 16 BIT 0 255 Fine Control of TILT Movement EN m COLOR WHEEL Hoi Taw gu COLOR WHEEL FINE ADJUSTMENT FINE Adjustment of Color Wheel to Any Position ROTATING GOBOS CONTINOUS ROTATION ONE 32 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com ELATION PLATINUM BEAM SR EXTREME DMX Channel Values Functions 18 DMX Channels opecifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head MODE CHANNEL VALUE FUNCTION T ROTATING GOBOS FINE INDEX ROTATION Gobo Rotation FINE Indexing a ROTATING GOBOS INDEX ROTATION Gobo Indexing 128 189 Clockwise Rotation from FAST TO SLOW NO Rotation Counterclockwise Gobo Rotation from SLOW to FAST ROTATING PRISM PRISM GOBO MACROS MU OO u EaKEENE EN 0 255 Continuous Adjustment from NEAR to FAR FOCUS FINE Continuous FINE Focus Adjustment a SHUTTER STROBE DIMMER INTENSITY 255 Intensity O to 100 Ea DIMMER INTENSITY FINE 0 255 Dimmer Intensity FINE Adjustment 33 PLATINUM BEAM SR EXTREME User
3. Environmental Conditions Power Voltage Usage Patterns On Off Cycling Control and Dimming EFFECTS Frost Motorized Focus strobe 1 18 fps Electronic Dimming 0 100 8 Facet Rotating Prisms and Macros COLOR 12 Colors Including UV CTO CTB GOBOS 8 Metal Rotating Indexing Interchangeable Gobos CONTROL CONNECTIONS 3 DMX Channel Modes 12 14 18 Remote Device Management Pan Movement 5407 630 Tit Movement 270 6 Button Control Panel Full Color 180 Reversible LCD Menu Display 16 Bit 3 Phase Pan Tilt Motors 3pin amp 5pin DMX In Out powerCON In Internal EWDMX Wireless DMX Receiver SIZE WEIGHT Length 13 9 352mm Width 13 0 329mm Vertical Height 20 0 509mm Weight 44 0 Ibs 20 0 kg ELECTRICAL THERMAL AC 100 240V 50 60Hz 350W Max Power Consumption 14 F to 1 13 F 10 C to 45 APPROVALS CE cETLus IP20 Intertek 3104374 Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 37 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com COLORS AND GOBOS COLOR WHEEL GREEN YELLOW puer ORANGE PURPLE C LO C T B 3 4 Pos 5 Pos 7 Pos 8 Pos 10 Pos 11 INTERCHANGEABLE ROTATING GOBO WHEEL OD 213 8mm ID 6 0mm 00066600 Pos 2 Pos 3 Pos 4 Pos 5 Pos 6 Pos 7 Pos 8 IMPORTANT NOT
4. Junostraat 2 6468 EW Kerkrade The Netherlands 31 45 546 85 66 31 45 546 85 96 fax www elationlighting eu info elationlighting eu DOCUMENT VERSION 057 Please check www elationlighting com for the latest revision update of this manual D t Soft nu ocument 9OHWGOIO Channel Modes Version Version 11 2 15 12 14 18 Updated manual format 2 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com CONTENTS m v ane MA UA AN Fixture Overview TR 2 11 19 22 37 9 Technical Specifications Optional Accessories 3 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com ENERAL INFORMATION INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable lighting fixtures on the market today The fixture has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain important information regarding safety during use and maintenance UNPACKING Every fixture has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect
5. for a wireless DMX signal from an Elation Wireless Transmitter 057 If NO wireless signal is received it will electronically switch the wired DMX mode W AR NINOG NEVER connect a fixture to a controller via a DMX cable when the WDMX system is in use This could cause serious damage to the controller SETTING UP THE WDMX SYSTEM Follow the instructions included with the Elation EWDMX Transmitter and connect it to the output of your DMX controller To sync your fixture with the Elation EWDMX Transmitter follow the steps below e Initially the Wireless Indicator on the fixture control panel should be solid RED Press and hold the configuration button on your EWDMX Transmitter for about 3 seconds The RED GREEN LED indicators on the EWDMX Transmitter and the fixture should begin to flash rapidly for about 5 10 seconds while the two systems pair e Once the fixture is paired with the EWDMX Transmitter 1 the Wireless status indicators on the both the fixture and the EWDMX Transmitter will stop flashing and glow solid GREEN If paring is unsuccessful repeat the process until paring is secured he fixture will store the pairing information inside a nondestructive memory bank once q link is created between the fixture and an EWDMX Transmitter The fixture will remember the paired EWDMX Transmitter even if the fixture is turned OFF for extended periods of time 30 PLATINUM BEAM SR EXTREME User Manual Ver I www el
6. menu 29 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com EDIT PROGRAM Record Controller Working With Built In Program continued Example Program 2 includes scenes 10 11 12 amp 13 Program 4 includes scenes 8 9 amp 10 Program includes scenes 12 13 14 amp 15 Auto Pro Part 1 is Program 2 Auto Pro Part 2 is Program 3 Auto Pro Part 3 is Program 6 The 3 Slave groups run the Auto Program in certain time segments as shown in the following picture Part 1 e sommere semet Part 2 se me o s J Part 3 i d i 29 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com WDMX INTERNAL WIRELESS DMX RECEIVER SET UP The PATINUM BEAN 5R EXTREME is equipped with an internal Wireless DMX Receiver which is fully compatible with an Elation Wireless DMX System Access the Wireless DMX sub menu from the PERSONALITY menu and then select the desired WDMX connection function which includes WDMX Off Turn OFF Wireless DMX Activate WDMX Turn ON Wireless DMX Act amp Data Out Turn ON Wireless DMX and send DMX data to wired 3 5pin outputs Clean WDMX Memo Clear WDMX memory When the WDMX system is Activated the internal DMX IN XLR jacks are OFF However the internal DMX OUT XLR jacks will function normally If the fixture is powered ON with the internal WDMX system Activated it will automatically scan
7. must be clearly written on the outside of the retum package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice Items returned without a R A number clearly marked on the outside of the package will be refused and returned at customer s expense You may obtain a R A number by contacting customer support 35 IMPORTANT NOTICE There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty Damages resulting from modifications to this fixture and or The disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and or repairs o PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com LIMITED WARRANTY A Elation Professional hereby warrants to the original purchaser Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years 730 days and Elation Professional amp product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months 180 days from the original date of purchase This warranty excludes discharge lamps and all product accessories This warrant
8. this manual Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts brackets included with this fixture should be used for installation Any modifications will void the original manufactures warranty and increase the risk of damage and or personal injury e Never look directly into the light source of this fixture to prevent risk of injury to your retina which may induce blindness Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times he fan and air inlets must remain clean and never blocked Allow approx 6 15cm between this fixture and other devices or a wall for proper cooling e Always disconnect from main power source before performing any type of service and or cleaning procedure Only handle the power cord by the plug end never pull out the plug by tugging the wire portion of the cord e Do not operate this fixture if the power cord has become frayed crimped and or damaged If the power cord is damaged replace it immediately with a new one of similar power rating PLATINUM BEAM 5R EXTREME User Manual Ver I www elationlighting com ENERAL GUIDELINES NEVER OPEN THIS FIXTURE WHILE IN USE During the initial operation of this fixture a light smoke or smell may emit from the interior of the fixture This is a normal process and is caused by excess paint in the interior of the casing burning off fr
9. ALUES Default Settings in BOLD DESCRIPTION FUNCTION Ten Lamp Off Time XXXX Minutes Lamp OFF Time INFORMATION LastRun Password Password XXX Password 038 Clean Last Run ON OFF Reset Fixture Last Run Time Password Password 038 Password LAMP CONTROL 20 79 C 45 C 68 174 F 113 F 80 139 C 130 C 176 282 F 266 F ON OFF status Settings PERSONALITY Display Setting WDMX OFF De activate WDMX Wireless DMX Activate WDMX Activate WDMX Act amp Data Out Act amp Data Out Clean WDMX Memo Reset Wireless DMX Mem Reset Default ON OFF Restore factory settings 23 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com ELATIONO PLATINUM BEAM 5R EXTREME SYSTEM MENU Specifications and features are subject to change without any prior written notice MAIN MENU SUBMENU OPTIONS VALUES Defaut Setingsin Boro DESCRIPTION Rese O QReeAlMooS ReetPan l yo on ResetCoos o ReetCooWeel O Peset uncllon neseiGobos O Rests RestShuterondorDmmer Restons _ ReetOferMoos O O Test Channel Effect Adjust Manual Control PAN XX fmeAdwtmens Coibraion Calibrate Password Poswod050 Basic Mode DMX Channel Modes Extended Mode User Mode A ES OO User Mode B User Defined Channel Assignment User Mode C Channel Assignments select Programs select Pr
10. ELATION PLATINUM 5R EXTREME user manual PROFESSIONAL ELATION PLATINUM BEAM 5R EXTREME M User manual www elationlighting com 2015 ELATION PROFESSIONAL all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ELATION brands and product names are trademarks or registered trademarks of their respective companies ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe insufficient and negligent assembly installation rigging and operation of this product Elation Professional USA 6122 S Eastern Ave Los Angeles CA 90040 323 582 3322 323 832 9142 fax www elationlighting com info elationlighting com Elation Professional B V
11. ERSONALITY Status Settings Address Via DMX When ON define the desired DMX address via an external controller 1 Connect the fixture to the external controller and power ON 2 Set the DMX value of Channel 1 on the controller to 7 3 Set the DMX value of Channel 2 on the controller to 7 or 8 When set to 7 the DMX address can be set between 1 and 255 When set 8 the DMX address can be set between 256 and 511 4 Using Channel 3 on the controller set the desired DMX address of the fixture Example 1 If the desired DMX address is 57 set Channel 1 to a value of 7 set Channel 2 to a value of 7 and then set Channel 3 to a value of 57 Example 2 If the desired DMX address is 420 set Channel 1 to a value of 7 set Channel 2 to a value of 8 and then set Channel 3 to a value of 164 25641642420 o After setting Channel 3 to the desired DMX address value wait for approximately 20 seconds for the fixture to complete the address reset function EFFECT ADJUST Manual Control select and manually test and fine adjust each individual channel function Independently from DMX control board This function will center PAN and TILT motors and set dimmer to 100 PAN and TILT functions will still operate if the fixture needs to be positioned to a flat clear surface With the individual functions you can focus the light on a flat surface wall and perform fine adjustments 25 PLATINUM BEAM SR EXT
12. ICE REGARDING DIMENSIONS AND CUSTOM GOBOS OD Outside Diameter ID Image Diameter Due to varying manufacturing processes it is highly recommended to provide a gobo and holder sample from the fixture to 3rd party custom gobo vendors for accurate sizing PHOTOMETRIC DATA Distance 3 Beam Diameter lux fc FULL ON 100 100 9 299 55 363 5 143 35 915 3 337 Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 38 PLATINUM BEAM SR EXTREME User Manual Ver I DIMENSIONAL DRAWINGS 12 6 321mm 8 3 212mm 8 6 217mm 329mm www elationlighting com 19 1 485mm 14 8 20 0 375mm 509mm 5 0 129mm 352mm Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice OPTIONAL ACCESSORIES 39 PLATINUM BEAM SR EXTREME User Manual Ver I
13. Manual Ver I www elationlighting com ELATION PLATINUM BEAM SR EXTREME DMX Channel Values Functions 18 DMX Channels opecifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head O FROST 10 12 16 127 Disable FROST 128 255 Enable FROST PAN MOVEMENT SPEED MAX to MIN Speed 11 13 17 Blackout by Movement Blackout by ALL Wheel Changing NO Function goes INTERNAL PROGRAMS 12 14 18 34 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com ERROR CODES When power is applied the unit will automatically enter a Reset Test mode This mode brings all the internal motors to a home position If there is an internal problem with one or more of the motors an error code will flash in the display in the form of XXer were as XX will represent a function number For example when the display shows OEr it means there is some type of error with the Pan motor If there are multiple errors during the start up process they will all flash in the display For example if the fixtures has errors on Channel 1 2 and 5 all at the same time you will see the error message O2br and O5Er flash repeated 5 times If an error does occur during the initial start up procedure the fixture will self generate a second
14. REME User Manual Ver I www elationlighting com EFFECT ADJUST Calibration 05 ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION This function allows small adjustments to be made to the effect wheels Color ohutter etc to compensate for ware or in the event a sensor has been knocked slightly out of place Because improper use of this function can result in undesired operation this function has been password protected The password is 050 and must be entered each time the calibration menu function is entered Because calibration is an extremely delicate procedure instructions on performing this action are left out of this manual For a first time calibrator please contact our customer support team for step by step instructions USER MODE SET User Mode select operating mode which includes DMX Channel and User defined modes USER MODE SET Edit User Mode Create user defined channel orders allowing the fixture to match the channel order of other fixtures on the market for easier operation A total of three user modes may be configured User Mode A User Mode B and User Mode C EDIT PROGRAM Select Program select one of the 10 user defined internal Auto Programs EDIT PROGRAM Edit Program Edit any of the 10 user defined internal Auto Programs EDIT PROGRAM Edit Scenes Edit any of the scenes of the internal Auto Programs EDIT PROGRAM Record Controller The fixture features a
15. User Manual Ver I www elationlighting com DISCHARGE LAMP WARNING This fixture is fitted with q DISCHARGE LAMP which is highly susceptible to damage if improperly handled NEVER touch the lamp with your bare hands as the oil from your hands will shorten the life of the lamp Also NEVER move the fixture until the lamp has had ample time to cool Lamps are NOT covered under warranty conditions Avoid switching the fixture ON and OFF repeatedly in short intervals as this will reduce lamp life and intensity To achieve the intensity associated with discharge lamps these lamps use gas sealed in a high pressure environment to emit a brilliant output gt Due to the high pressure involved with The construction of the lamp the lamp MAY EXPLODE DURING PROLONGED EXTENSIVE USE This risk is increased with age added care is encouraged when dealing with older lamps Thus the lamp must always be replaced at the end of their recommended duty cycle Extreme caution should be used when operating this or any fixture fitted with a gas discharge lamp UV RADIATION NOTICE This fixture emits intense UV radiation which is harmful to The eyes and skin The intense luminance of the lamp can cause severe damage to the retina NEVER operate this fixture with ANY of the protective covers removed These covers have been specially designed to shield against UV radiation LAMP REPLACEMENT Please note that due to the nature of the Philips Platin
16. Ver I www elationlighting com LAMP SAFETY INSTRUCTIONS ALWAYS replace lamp every 2 000 Hours Use only Genuine Original Philips Platinum 5R lamps Other brand lamps may cause damage and void the warranty NEVER touch the lamp with your bare hands as the oil from your hands will shorten the life of the lamp Always disconnect the fixture s main power supply before replacing lamp Allow fixture to cool for at least 15 minutes before attempting any type of service Make sure ALL covers panels are replaced secured before operating the fixture to prevent any risk and or damage to eye retina from UV Radiation exposure LAMP INSTALLATION PROCEDURE l Place fixture on a flat surface and remove 4 screws marked A B C and D and then remove rear cover plate see image below fo access the lamp LAMP COVER PLATE LAMP PLATINUMSR T 45 C Te 1 00 bd i 12 PLATINUM BEAM SR EXTREME User Manual Ver I ATION www elationlighting com 3 Using two fingers on your RIGHT hand pull the retention handle OUT and towards the RIGHT as far as possible 13 PLATINUM BEAM SR EXTREME User Manual Ver I ATION www elationlighting com 4 While pulling the retention handle with your RIGHT hand use your LEFT hand to gently twist the lamp COUNTERCLOCKWISE to remove it from under the retention brackets 14 PLATINUM BEAM SR EXTREME User Manual Ver I LATION www elationlighti
17. ationlighting com CLEARING EWDMX TRANSMITTER LINK e Access the Wireless DMX sub menu from the PERSONALITY menu and then select Clear WDMX Memo to clear any existing link between the fixture and a EWDMX Transmitter The Wireless indictor on the fixture will turn solid RED when the link is severed You may also clear the link directly from the EWDMX Transmitter First be sure the fixture s is powered ON and then hold down the configuration button on the EWDMX Transmitter for as least 5 seconds This will automatically clear the link between the EWDMX Transmitter and any fixture that is powered ON All EWDMX indictors will glow solid RED if the procedure was successful FIXTURE WIRELESS INDICATOR RED GREEN Rapid Flashing Syncing to an EWDMX Transmitter RED GREEN Slow Flashing Paired with an EWDMX Iransmitter buf not receiving a DMX signal from a controller GREEN Solid Paired with an EWDMX Transmitter and receiving DMX data RED Solid Not paired with an EWDMX Iransmitter FREE 31 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com DMX CHANNEL FUNCTIONS AND VALUES ELATIONO PLATINUM BEAM SR EXTREME DMX Channel Values Functions 18 DMX Channels opecifications are subject to change without any prior written notice Rotation direction Clockwise or Counterclockwise of COLOR GOBO and PRISM effects depends on the orientation of the fixture head MODE BIA VALUE FUNCTION
18. e lamp be replaced every 2 000 Hours This is done to protect the internal optical system as well as prevent accidental lamp explosion which could lead to hot glass particles falling from the fixture IE At 2 000 Hours the LCD control display will begin to flash Replace The Lamp and FAILURE TO CHANGE THE LAMP WITHIN 300 HOUR of the 2 000 HOUR RATED LIFE WILL CAUSE THE FIXTURE TO AUTOMATICALLY SHUT DOWN the lamp will flicker for the first five minutes of operation At this point the lamp has reached the maximum rated life and should be replaced immediately After the lamp has flickered for about five minutes it should strike normally allowing the fixture to be used temporarily until a replacement lamp can be installed The fixture will continue to operate for an additional 300 hours however the Replace the Lamp warning will continue to flash in the display Keep in mind that the flicker protection circuitry will only work for about 300 Hours lamp clock life of 2 000 2 300 Hours After 2 300 Hours The fixture will no longer respond to DMX commands and immediately enter a hibernation mode that will electronically discontinue all fixture functionality with the exception of a few menu commands The fixture will continue to enter hibernation mode until the lamp is replaced and the lamp clock has been reset To replace the lamp follow the safety guidelines and procedures listed on the next page 11 PLATINUM BEAM SR EXTREME User Manual
19. e next page 17 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com LAMP HOURS RESET PROCEDURE l 2 Activate the main menu by pressing MODE ESC and toggle to Information Press ENTER and press UP or DOWN to toggle to Time Information Press UP or DOWN fo toggle to L Timer Password and press ENTER Then press UP or DOWN to enter the reset pass code 038 and press ENTER to confirm The display will automatically revert to L Timer Password next press UP or DOWN to toggle down to Clear Lamp Time Press ENTER and select ON The lamp timer has now been reset press MODE ESC To exit the menu and return to the home screen LAMP OPTIMIZATION Unlike traditional discharge lamps the Philips Platinum 5R PRO Lamp does NOT require optimization Ihe lamp orientation and optimization procedure has been preset during the manufacturing process of the lamp Please remember the Philips Platinum 5R PRO Lamp is NOT a hot restrike lamp therefore you must wait approximately 15 minutes before you can attempt to restrike the lamp once it has been turned off 18 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com FIXTURE INSTALLATION FLAMMABLE MATERIAL WARNING Keep fixture at least 5 0 ff 1 5m away from any flammable materials decorations pyrotechnics etc ELECTRICAL CONNECTIONS A qualified electrician should be used for dll electrical connections and or installati
20. le remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall Elation Professional be liable for any loss and or damage direct and or consequential arising out of the use of and or the inability to use this product G This warranty is the only written warranty applicable to Elation Professional amp products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com SAFETY INSTRUCTIONS This fixture is an extremely sophisticated piece of electronic equipment To guarantee a smooth operation it is important to follow the guidelines in this manual The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual This device falls under PROTECTION CLASS 1 It s essential this device be grounded properly Only qualified personnel should perform all electrical connections I N DOOR S U SE ONL Y DO NOT EXPOSE FIXTURE RAIN AND MOISTURE UNPLUG POWER BEFORE SERVICING FIXTURE DO NOT PLUG FIXTURE INTO A DIMMER PACK NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK For proper operation follow the Installation guidelines described in
21. manual D This is not a service contract and this warranty does not include any maintenance cleaning or periodic check up During the periods as specified above Elation Professional amp will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Elation Professionale under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of Elation Professional amp All products covered by this warranty were manufactured after January 1 1990 and bare identifying marks to that effect E Elation Professional reserves the right to make changes in design and or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with the products described above Except to the extent prohibited by applicable law all implied warranties made by Elation Professionake in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty periods set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said periods have expired The consumer s and or dealer s so
22. n integrated DMX recorder by which you can transmit the programmed scenes from your DMX controller to the moving head Adjust the desired scene numbers via the encoder from to When you call up the scenes at your controller they will automatically be transmitted to the moving head 26 PLATINUM BEAM SR EXTREME User Manual Ver 1 www elationlighting com EDIT PROGRAM Record Controller Working With Built In Programs A Master unit can send up to 3 different data groups to the Slave units i e a Master unit can start 3 different Slave units which run 3 different programs The Master unit sends the 3 program parts in a continuous loop Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 The Slave unit receives data from the Master unit according to the group which the slave unit was assigned to If e g a Slave unit is set to Slave 1 in the menu Set to Slave the Master unit sends Auto Program Part 1 to the Slave unit If set to Slave 2 the Slave unit receives Auto Program Part 2 To start an Auto Program proceed as follows 1 Slave Setting gt elect Function Mode e Press ENTER to confirm Select Set to Slave Press ENTER to confirm Select Slave 1 Slave 2 or Slave 3 Press ENTER to confirm Press MODE ESC in order to return to the main menu 2 Automatic P
23. ng com 5 Using two fingers on your RIGHT hand pull the retention handle OUT and towards the RIGHT os far as possible 6 While pulling the retention handle with your RIGHT hand use your LEFT had to gently install the lamp under the retention brackets by holding the lamp at a slight angle and positioning it until it is flush with the base 15 PLATINUM BEAM SR EXTREME User Manual Ver I ATION www elationlighting com 7 While still holding the retention handle with your RIGHT hand gently turn the lamp CLOCKWISE with your LEFT hand until the lamp is correctly aligned under the retention brackets 8 Release the retention handle with your RIGHT hand and make sure the handle is upright and not at an angle 16 PLATINUM BEAM SR EXTREME User Manual Ver 1 ATION www elationlighting com 10 Replace the lamp cover back into place by securing 4 screws marked A B and D LAMP PLATINUMSR Ta gt 45 C 100 eee O Use only Gen O ee O lamps Ore ira tana maros w A 11 Be sure to reset the LAMP HOURS in the system menu to prevent the protection Circuitry from accidently shutting off the lamp during normal operation 12 If the lamp protection circuitry has already been initiated and the LAMP HOURS is not reset the Replace the Lamp warning will continue to flash and fixture will eventually shut down To reset LAMP HOURS see instructions on th
24. ns are recommended to insure proper function and extended life There are no user serviceable parts inside this fixture please refer all other service issues an authorized Elation service technician Should you need any spare parts please order genuine parts from your local Elation dealer Please refer to the following points during routine inspections A detailed electric check by an approved electrical engineer every 3 months to make sure the circuit contacts are in good condition and prevent overheating Be sure all screws and fasteners are securely tightened at all times Lose screws may fall out during normal operation resulting in damage or injury e Check for any deformations on the housing color lenses rigging hardware and rigging points ceiling suspension trussing Deformations in the housing could allow for dust to enter into the fixture Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person s Inspect all moving parts and make sure there are no signs of wear and rotate move without imbalances Electric power supply cables must not show any damage material fatigue or sediments Never remove the ground prong from the power cable 3 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com TECHNICAL SPECIFICATIONS SOURCE 189W Platinum 5R Lamp 2 000 Hour Average Life May vary depending on several factors including but not limited to
25. ograms To Be Run Edit SfepOl SCex Program n loop 10 0 0 Edit Program Pani Fade Time Edit Scenes Manual Scenes Edit Scene Time Scene 250 Input By Outside Stores Scenes via Ext DMX Console Record Controller XX XX Automatic Scenes Recorder User Mode FUNCTION Auto Program Define fixture mode Master or Alone for running Auto Programs Select desired internal programs under Select Program set the number of steps under Edit Program and edit individual scenes under Edit Scenes This counter can be reset LAMP CONTROL Lamp ON at Temp The fixture is designed to shut the lamp OFF when an excessive temperature is sensed inside the head by the on board CPU The lamp is shut OFF to prevent damage to the lamp and avoid possible internal damage to the fixture head This function sets the MIN internal operating temperature of the fixture head before the lamp will restrike after the lamp has been automatically shut OFF 24 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com LAMP CONTROL Lamp OFF Temp The fixture is designed to shut the lamp OFF when an excessive temperature is sensed inside the head by the on board CPU The lamp is shut OFF to prevent damage to the lamp and avoid possible internal damage to the fixture head This function sets the MAX internal operating temperature of the fixture head when the lamp will automatically be shut OFF P
26. om the heat associated with the lamp and will decrease gradually over time This fixture is a professional lighting effect designed for INDOOR DRY LOCATIONS ONLY on stage in nightclubs theatres etc Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating to prevent any fire hazard The fixture must be installed in a location with adequate ventilation at least 1 5 feet Sm from adjacent surfaces Be sure no air ventilation slots are blocked DO NOT attempt installation and or operation without knowledge how to do so DO NOT permit operation by persons who are not qualified to operate this type of fixture Most damages are the result of operations by nonprofessionals Consistent operational breaks may ensure the fixture will function properly for many years fo come DO NOT shake fixture avoid brute force when installing and or operating fixture Always install the fixture with an appropriate safety cable When installing the fixture in a suspended environment always use mounting hardware that is no less than MIO x 25 mm also be sure the hardware is insert in the pre arranged screw holes in the bracket of the fixture Use the original packaging and materials to transport the fixture in for service DO NOT TOUCH the housing bare hand during its operation Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing Or serving 8 PLATINUM BEAM SR EXTREME
27. ons Isr CAUTIONS For added protection mount the fixture in areas outside walking paths seating areas or in areas were unauthorized personnel might reach the fixture Ambient operating temperature range for this fixture is 14 to 113 F 10 to 45 C Do not use the fixture under or above this temperature Before mounting the fixture to any surface make sure the installation area can hold a minimum point load of 10 times the weight of the fixture Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing 19 PLATINUM BEAM SR EXTREME User Manual Ver I ATION www elationlighting com MOUNTING POINTS Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Fixture is fully operational in the specific mounting positions as illustrated below WSZ SS al at n UP Al WAS AA NA lt 2 es se Ta N i So a N x lt SZ 2 din YU x MA Jf S Z T M AS AS JZ a AN Z sZ 2 db
28. ons of each command in the system menu LCD MENU CONTROL PANEL The control panel see image below located on back of the fixture allows you to access the main menu and make all necessary adjustments to the fixture During normal operation pressing MODE ESC button once will access the fixture s main menu Once in the main menu you can navigate through the different functions and access the sub menus with the UP DOWN RIGHT and LEFT buttons Once you reach a field that requires adjusting press the ENTER button to activate that field and use the UP and DOWN buttons to adjust the field Pressing the ENTER button once more will confirm your setting You may exit the main menu at any time without making any adjustments by pressing the MODE ESC button NOTE To access the LCD Menu Control Display via the internal battery press and hold the DC SWITCH button for 2 seconds The LCD Menu Control Display will shut OFF automatically about 1 minute from the last button press To shut OFF the LCD Menu Control Display immediately set Reset Default menu option to ON in the Personality menu and press the ENTER button to confirm your selection EcAT OR PLATINUM AE UII o 22 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com ELATION PLATINUM BEAM 5R EXTREME SYSTEM MENU opecifications and features are subject to change without any prior written notice MAIN MENU SUBMENU OPTIONS V
29. reset signal and try to realign all the motors and correct the errors If the error persists affer a second attempt a third attempt will be made If after a third attempt all the errors have not been corrected the fixture will make the following determinations 3 or More Errors The fixture cannot function properly with three or more errors therefore the fixture will place itself in a stand by mode until subsequent repairs can be made Less Than 3 Errors The fixture has less than 3 errors therefore most other functions will work properly The fixture will attempt to operate normally until the errors can be correct by a technician The errors in question will remain flashing in the display as a reminder of internal errors PAN Er Gobo Rot 1 Er TILT Er 35 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com CLEANING AND MAINTENANCE C A U T Disconnect power before cleaning or maintenance CLEANING Frequent cleaning is recommended to insure proper function optimized light output and an extended life The frequency of cleaning depends on the environment which the fixture operates damp smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture s optics e Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt debris accumulation Never use alcohol solvents or ammonia based cleaners MAINTENANCE Regular inspectio
30. rogram Run Select Function Mode e Press ENTER to confirm Select Auto Program e Press ENTER to confirm e Select Master or Alone Press ENTER to confirm Press MODE ESC in order to return to the main menu 27 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com EDIT PROGRAM Record Controller Working With Built In Program continued 3 Program Selection for Auto Pro Part e elect Edit Program Press ENTER confirm Select Select Programs Press ENTER confirm Select Auto Pro Part 1 Auto Pro Part 2 or Auto Pro Part 3 and select which olave program is to be sent Selection Part 1 means that the Slave unit runs the same program as the master units Press ENTER to confirm Press MODE ESC in order to return to the main menu 4 Program Selection for Edit Program elect Edit Program Press ENTER confirm select Edit Program Press ENTER confirm Select the desired program With this function you can edit specific scenes into a specific program Press ENTER to confirm Press MODE ESC in order to return to the main menu 9 Automatic Scene Recording e Select Edit Program Press ENTER confirm Select Edit Scenes Select desired scene numbers A maximum of 250 scenes can be programmed Press ENTER to confirm Press MODE ESC in order to return to the main
31. um 5R Lamp and the optical path of the Elation PLATINUM BEAM 5R EXTREME fixture the lamp MUST BE replaced at 2 000 hours Use only Genuine Original Philips platinum lamps Other brand lamps may cause damage and void warranty 9 PLATINUM BEAM SR EXTREME User Manual Ver I gt gt 19 20 10 11 12 13 14 15 16 17 18 www elationlighting com LED Assembly LCD Menu Function Display Wireless DMX Indicator DC Switch Microphone LEFT Button DOWN Button RIGHT Button MODE ESC Button UP Button ENTER Button Wireless DMX Antenna Carrying Handle s Lamp Access Cover Panel 3pin DMX Input 3pin DMX Output 5pin DMX Output 5pin DMX Input powerCON Input Fuse 10 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com LAMP INSTALLATION INSTRUCTIONS LAMP REPLACEMENT Please note that due to the nature of The Philips Platinum 5R Lamp and the optical path of the Elation PLATINUM BEAM 5R EXTREME fixture the lamp MUST BE replaced at 2 000 hours Use only Genuine Original Philips Platinum 5R Lamps Other brand lamps may cause damage and void warranty INSTALLING OR REPLACING THE LAMP To ensure a proper safe lamp change carefully read all the following instructions LAMP PROTECTION CIRCUITRY Because of the nature of the extreme heat associated with the Philips Platinum 5R lamp and the tight nature of the internal optical system it is IMPERATIVE that th
32. y shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the fime service is sought B For warranty service send the product only to the Elation Professional amp factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty Elation Professionale will pay return shipping charges only to a designated point within the United States If any product is sent it must be shipped in its original package and packaging material No accessories should be shipped with the product If any accessories are shipped with the product Elation Professional amp shall have no liability what so ever for loss and or or damage to any such accessories nor for the safe return thereof C This warranty is void if the product serial number and or labels are altered or removed if the product is modified in any manner which Elation Professional amp concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional amp if the product is damaged because not properly maintained as set forth in the product instructions guidelines and or user
33. your unit for damage and be sure all accessories necessary to operate the unit have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Please do not return this unit to your dealer without first contacting customer support at the number listed below Please do not discard the shipping carton in the trash Please recycle whenever possible 4 PLATINUM BEAM SR EXTREME User Manual Ver I www elationlighting com CUSTOMER SUPPORT Elation Professionale provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www elationlighting corn for any comments or suggestions For service related issue please contact Elation Professional ELATION SERVICE USA Monday Friday 8 00am to 5 00pm PST Voice 323 582 3322 Fax 323 832 9142 E mail support elationlighting com ELATION SERVICE EUROPE Monday Friday 08 30 to 17 00 CET Voice 31 45 546 85 30 Fax 31 45 546 85 96 E mail support elationlighting eu WARRANTY REGISTRATION Please complete and mail in the enclosed warranty card or register online http www elationlighting com Login aspx to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number

Download Pdf Manuals

image

Related Search

Related Contents

LG split hi-wall - Manual do Propietario  Ergotron DS100 Sliding Display Bracket  mics Jr.  JBL BPx500.1 Car Amplifier User Manual  Pioneer F30 Quick Start Guide  MPS File Format  2009/09/17 Ver.1.1  LA/01/65  Parallels Plesk Control Panel 8.6 für Windows  SPN-01 取扱説明書  

Copyright © All rights reserved.
Failed to retrieve file