ASP user manual
Contents
1. Quick Start PDF Environment Wind Speed moh Drag lett to increase sensitivity or right to decrease false alerts due to wind Orientation Azimuth Angle 1625 Angle relative to north 90 is East Location OE MGRS 185 TJ 90279 1774 This will be converted to GPS for use on the spotter Lat 38 983477 90 0 to 90 0 Long 180 0 to 180 0 Elevation 1381 In meters HAE WGS B4 Time UTC Tue 11 Sep 2012 19 57 16 Current time on the spotter Click acquire to use PC s time Sync with GPS will update from GPS regularly Figure 10 Radar Software Quickstart Config Tab Network Configuration As mentioned above the IP address of the radar is set to 192 168 0 20 and the subnet mask is 255 255 255 0 as seen in the figure below If for some reason this address were to be changed or corrupted the user can connect to the default ip address of the radar at 169 254 254 254 In this case the Base Station laptop must be set to the same subnet 169 254 254 xxx SpotterRE a ckStart Network Outputs Network Custom Address l i IP Address 192 168 0 20 Static address for the unit Ex 192 168 1 15 Netmask 255 255 255 0 A bitmask to divide networks into subnets Ex 295 299 299 0 Gateway D A network node used to access other networks Ex 192 168 1 1 DHCP Address IP Address Overrides user set IP if in same subnet Netmask Gateway Overrides user gateway if set Hint Auto configur2. S 4 DOG Command amp Control File Help Name IP 192 168 0 2 Max Cre Figure 21 Camera and DVR Configuration Exit the Application To exit the S4 C2 application click on the File menu and then select Exit or simply click on the X in the upper right corner of the application window and the application will shut down DRI Kit v1_manual v1 1 15 Troubleshooting 1 The radar unit does not appear to power up It may take several minutes for the data link to establish a connection with the radar Also check the length of the CAT 5 cable connecting the radar If itis over 100m then two CAT 5 cables are required out to 300m 2 The radar does not appear to connect to the system Open the Google Chrome browser window on the Base Station Processing Module and type in http 192 168 254 254 to connect to the radar Contact Info Tech Support For questions or support please see our website at www bcfsolutions net or contact admin bcfsolutions net 703 956 9088 For user manual or other technical downloads go to the customer tab on the website and login with the following user customer password 2004 S4Tech This being a new product there may not be much information on the customer page at this time DRI Kit v1_manual v1 1 16
3. process The default grid can be changed to a 250m or 1000m grid or to a default map by selecting the Swich Map option in the popus menu and then selecting the desired option in the submenu Cameras and radars are added to the map using the pop up menu also as seen by the options in the figure below DRI Kit v1_manual v1 1 12 Place PTZ Camera Here Place Fixed Camera Here Remove Camera Place Radar Here Remove Radar Register Grid Map 2s Import Map Remove Map sAtechmap Switch Map Figure 18 Main Config Menu on Map Tab The default map option is shown below G S4 DOG Command amp Control File Help Time Lat 38 982433 Distance m 0 Lon 77 419114 Bearing 0 Figure 19 Default Map DRI Kit v1_manual v1 1 13 Configuring the Radar Position It is important that the radar bearing and position on the map or grid correspond to the Orientation azimuth angle and Position Latitude Lat Longitude Long shown in the radar browser or the targets will not display in the right locations The radar bearing is entered by the user when the radar is first placed onto the S4 C2 map and can be seen by the direction that the radar pattern is pointing as seen in the figure below The user should verify that this matches with the Orientation Azimuth Angle settings on the Quickstart tab of the radar browser The radar location on the map is determined by where the user clicks the mouse before right
4. EN BCE solutions DIGITAL OBSERVATION GUARD Radar Interface Kit User Manual Version 1 1 June 4 2013 Table of Contents Syo eM DESC PO ER a ed ad in dl lien 2 Connecting the Rad arto te Base Stal ON ees admet en nettes ans 2 Comeon ahokada CE RD este atteint a ile und 5 COMME CTI to he RATES nn asec ise cts sa tete id we ceeded eb aaah dee thei nt 6 Quicks tar CONMeuUrall ON acca ta een ed ane AM ANA ath it 6 INGE WOK CONDS UTTO Moni a tagsnduachaaidcns it mec a Rien ini 7 NAN ne Radir DATES SR SU cee D NS alse head 8 Using the S4 Tech Command and Control Software Application 9 Contisure the Radar OPUS RAR ne AN dE Re er ir tr 9 R n the SAC Appease da tient too nan nies 10 DO INA AWE A ap hcersath viens a ap lacesar a E tet Aetna aise ha al sane E 11 Chaneine or Loading a MAD sn ee Sn SA ee DR a nn ee 12 Configuring the Radar Position sis ccssicecsenserxesveniverecentancenexdewebesserqdasanduadeceadanssiendesedaesareaatendantecssadeasiecs 14 Re Ses a ect hog MAD er mor ears er ee E ee ee ree den 14 Exit he Appl CaO mens pass Mana a a de dei tes 15 STIMULI VS SOON RS sacs pace ade esc tar teen ect tee nier nie r een ete ae un 16 Contact Info TeCh SUPPO sendis due Monastir 16 Table of Figures Fisure i Radar Kitwith Military Grade CAS nm tentera enceinte 2 Pisure 2 Radar Interface Kit Identitication Labels en ten te a E Mion monte 2 Figure 3 Radar Remote Module CAT 5 Primary Connections 125m or less 3 Figu
5. MAGE ES AGAR tL Raa Figure 6 Powering Up the Radar Base Station With the Radar and Radar Base Station powered up connect a CAT 5 cable to any of the connectors labeled J1 J4 on the Radar Base Station to the Base Station computer DRI Kit v1_manual v1 1 J1 Ja Et hornet LAN Interfaces Figure 7 Connecting Radar Base Station to Computer Connecting the Radar GPS To connect the optional GPS to the DOG Radar first plug in the GPS connector into the Radar as shown in the figure below The GPS contains a magnetic strip that will allow it to easily attach to the top of the radar and stay without any mounting hardware Figure 8 Connecting GPS to the Radar DRI Kit v1_manual v1 1 Connecting to the Radar Once everything is properly connected power up the system The Radar takes approximately thirty seconds to a minute to fully power up and initialize Use the Base Station laptop to open up a Google Chrome web browser by double clicking on the Google Chrome icon as seen in the figure below The IP address of the Radar is set to 192 168 0 20 The Chrome browser is set to automatically load the Radar s configuration page when it is run The IP address of the Base Station laptop is set to 192 168 0 3 Enter IP Address of Radar chrome oe FE he ee masse ST t F il O Figure 9 Connect to Radar with Chrome Browser QuickStart Configuration Whenever a Radar is installed in a new location it is important to c
6. clicking the pop up menu to add the radar The Lat Long location of the mouse click can be seen in the bottom right of the screen as shown in the figure below The user should verify that this matches with the Position Lat Long settings on the Quickstart tab of the radar browser 4 DOG Command amp Control File Help Map Cameras Orientation azimuth angle Radar Position Lat 38 983648 Distance m 0 Lon 77 421165 Bearing 0 Figure 20 Radar Bearing and Position Verification The Cameras Tab The cameras tab is the where fixed cameras PTZ cameras and DVR units are set up in the S4 C2 application as seen on the main tab in the figure below For each component that is added submenus will pop up and the appropriate parameters must be entered by the user PTZ cameras have IP addresses TCP ports DVR channel and motion detection parameters that must be entered Fixed cameras have DVR channel and motion detection parameters DVR s have IP addresses and maxium number of channels to be entered as seen in the figure below As on the map tab the virtual joystick in the upper right corner controls one or more attached PTZ cameras Please refer to the Help menu in the S4 C2 application for more operational detail DRI Kit v1_manual v1 1 14 S S4 DOG Command amp Control 192 168 0 10 2 iik i d i l j
7. e DHCP Dynamic DNS using network json Push Notification Fixed Address Default address 169 254 254 Always accessible when plugged directly into Spotter Netmask Gateway DRI Kit v1_manual v1 1 Figure 11 Radar Software Network Config Screen Viewing Radar Data Once the Radar has been properly setup click on the Tracker tab in the upper right hand corner of the webpage The Radar s Tracker Display page will open up in a new browser window as shown in the figure below fs nas OF D Tracker Display G 192168 020 LT E 022 R00 483m 230 340 350 d 10 20 7 012 R02 163m F S SDI R13 168M T 018 R12 342m 011 L02 383m a 003 R18 464m s 0157 R60 591m ERAN Figure 12 Radar Tracker Display Screen The grid display shows the range and angle contours along with the radar personnel detection pattern Target tracks are displayed as unique colored squares with an adjacent track ID as seen in the figure above The range and bearing associated with the track ID are displayed in a matching color in the upper left or right corner of the grid The display can be configured by clicking on the SpotterRF icon in the upper left corner of the grid When clicked on the icon expands into the high level configuration menu options as seen in the figure below Click on each option to set up background color line and text sizes grid labels target display options etc Mask zones can al
8. e PTZ and fixed cameras on the map e place and remove radar Register grid map Import and remove a local map Switch between different maps No It seoctos Figure 16 S4 C2 Help Document The Map Tab The figure below shows the Map tab of the application It contains a default 500m grid with a radar fixed camera and PTZ camera placed on the grid The radar personnel detection pattern is shown as yellow oval and it points in the direction of the user entered bearing for the radar The PTZ and fixed camera fields of view and shown as green and blue fans respectively and also point in the direction of the cameras Motion detection or sensor alarms from a connected DOG Base Station DVR will cause the DRI Kit v1_manual v1 1 11 fans to turn red and flash along with an audible tone that can be disabled Video from the corresponding alarms can be seen on the DVR under that camera s channel The virtual joystick in the upper right corner of the page will control one or more connected PTZ cameras C54 DOG Command mi dE File Help Sensor Alam Type Time Figure 17 S4 C2 Map Tab with 500m Default Grid Changing or Loading a Map The default grids or maps can be changed by right clicking anyware on the map or grid graphic and using the pop up menu as seen in the figure below Maps can be added with the Import Map option or removed with the Remove Map option See the Help menu for more details on this
9. e Rate 1 seconds tracks json http 192 168 0 3 4444 view details Figure 14 Configure the Radar for S4 C2 Software Note To check that the rada is outputting target data open another Google Chrome browser page and enter the following url 192 168 0 20 tracks json You will see the latest serial message sent by the radar in the browser window Running the S4 C2 Application Once the radar outputs have been configured to The run the S4 Tech Command and Control application double click on the S4 Command and Control desktop icon as indicated in the figure below to launch the application DRI Kit v1_manual v1 1 10 Figure 15 Start S4 C2 Software The S4 Command and Control application will open up in a new window Note If no DOG Base Station or PTZ camera are connected to the laptop then it may take a minute or two before the application opens as it searches for connected devices Once open the user can click on the Help menu on the upper left to see a full set of help instructions for the application The main page of the help menu is seen in the figure below E DOGControl pdt Adobe Reader el E Edit View Document Tock Window Help x lag 2 10 f g fm La DOG Command amp Control 1 Map By default the map contains 3 grid maps with 250m 500m and 1km range respectively 1 1 Context Menu You can right click the map to bring up the context menu to perform the following tasks Place and remov
10. onfigure several radar settings Click on the Quick Start tab at the top of the web browser to see the screen in the figure below The Environment Wind Speed setting is used to help eliminate false alarms generated by the wind blowing trees and other objects within the Radars field of view Increaseing the environment wind speed reduces the sensitivy of the Radar Itis recommended to start with a slow wind speed and gradually increase the setting until all false alarms stop The Orientation Azimuth Setting is critical to properly aligning Radar s angle relative to north Type in the angle in degrees relative to true north that the radar is pointing The Location Lat Long Elevation setting is critical for determing the exact location of the Radar If the GPS module is connected to the Radar then the location information will automatically be uploaded to the software The location information can also be manually entered should it be necessary Note If possible it is a good idea to verify the GPS location of the radar especially if the map based version of the software is to be used Once all of the Radar settings have been properly configured it is important to click on the Save button at the bottom of the webpage to save all of the settings Note Consult the Radar s user manual for a more detailed description of these settings as well as many other non critical settings DRI Kit v1_manual v1 1 QuickStart User Manual PDF
11. re 4 Radar Remote Module CAT 5 Auxillary Connections 125m 450m cccccccssseseseeeeeeeeeees 3 Figure 5 Connecting Radar Remote Module to Base Station 4 Figure 6 Powerins Up th Radar Base STAIOM sentent 4 Fisure 7 Connecting Radar Base station to Computer NU into 5 Figure 8 Connecting GPS to the Radar ss 2 Figure 9 Connect to Radar with Chrome BrowSer vveves lt srvevseteteiveretuesoesstey en nan NEE ee 6 Figure 0 Radar sottware Quickstart Contre Abies us sen M ct nr ne M ar 7 Figure 11 Radar Software Network Config Screen ss 8 Picture 12 Radar Tracker Display Scree wpa en noi es en anis 8 Pour So Display Onis Meniere ee see da mie ai doc doi 9 Figure 147 Configure the Radar for S4 C2 SOltw are Le mena ae denis 10 TOUT ESS ASC SON RSS a ae cd ee 11 Fisur 1G S4 C2 Help DOCUMENTER nn channel men aan ete 11 Figure 17 S4 C2 Map Tab with 500m Default Grid ss 12 Pisure 3 Mam Contie Menton Map Taboes ds Se tn de ne NN 13 Fie ore 19 eka Wap sectie ne ae ae 13 Figure 20 Radar Bearing and Position Verification sise 14 Pioure 21 Camera and DV IR CONS ura EL T etre le de 15 DRI Kit v1_manual v1 1 System Description The DOG Radar Interface Kit provides the capability to remotely power and connect to a DOG radar sensor and to display and configure the radar data on the base station laptop The DOG radar interface kit will power a Spotter radar out to 150m with a
12. s 125m or less When connecting the Radar to the Base Station over distances betweem 125m and 450m a second CAT 5 cable needs to be run and connected to the J3 connector to extend the operational capabilities as shown in the figure below EW ARNING DO NOT REMOVE THE WEATHERTIGHT CONNECTOR ON THE BOTTOM OF THE RADAR HEAD CONNECTING THE PRIMARY OR SECONDARY CABLES DIRECTLY INTO THE RADAR MAY DAMAGE THE RADAR Figure 4 Radar Remote Module CAT 5 Auxillary Connections 125m 450m Once the CAT 5 cables have been plugged into the the Radar Remote Module the other end of the cables can be connected to the Radar Base Station The primary cable that was plugged into connector J1 on the Radar must be plugged into the connector labeled J6 on the Base Station If second cable is plugged into DRI Kit v1_manual v1 1 connector J3 on the Radar then connect the other end of this cable into the connector labeled J7 on the Base Station i Figure 5 Connecting Radar Remote Module to Base Station It is highly recommended to attach a grounding wire to the grounding post on the Radar Base Station and clamp the other end to a to a large metal structure pipe or electrical outlet ground as shown in the figure below This will help to protect the hardware and user against lightning Next plug in the 40Vdc adapter into the J5 connector on the Radar Base Station to power up the radar DO MOT CONNECT MARIE STATA DE CPE TL TES MP a FE SEVERE DA
13. single primary CAT 5 cable and up to 500m using a second CAT 5 cable The figure below shows the various components in the DOG Radar Interface Kit 1 Radar Remote Module NOTE Remote Modules may already integrated onto the Radar Radar Base Station G 40Vdc Power Supply a AC Power Cord User Manual Figure 1 Radar Kit with Military Grade Case Each case 1s identified by a decal just above the handle as shown in the figure below DOG Radar Interface Kit P N DRI Kit v1 S N DRI 00100 NSN 5820 01 601 7427 Figure 2 Radar Interface Kit Identification Label Connecting the Radar to the Base Station Begin connecting the Radar to the Base Station by removing the weatherproof connector gland for the connector labeled J1 Run a CAT 5 cable through the weatherproof gland and plug the RJ 45 connector into JI as shown in the figure below If the cable distance being run from the radar to the base station is 125m or less in length then J1 is the only connection that needs to be made between the radar and the base station In this case it is extremely important to put a small piece of CAT 5 cable into the other cable gland to insure an environmentally tight seal DRI Kit v1_manual v1 1 kW ARNING DO NOT REMOVE THE WEATHERTIGHT CONNECTOR ON THE BOTTOM OF THE RADAR HEAD CONNECTING THE PRIMARY OR SECONDARY CABLES DIRECTLY INTO THE RADAR MAY DAMAGE THE RADAR Figure 3 Radar Remote Module CAT 5 Primary Connection
14. so be set up so that no detections occur in those areas DRI Kit v1_manual v1 1 Le 40 do 20 L KHY 5 NL RAC F SES ERR PES Figure 13 Display Config Menu Using the S4 Tech Command and Control Software Application S4 Tech has developed a command and control software application that combines maps grids and icons with Spotter radar DOG Base Station DOG standard camera and DOG PTZ camera interfaces The software allows the user to select a default grid display or to import a map image in any standard image format Fixed camera PTZ camera sensor and radar icons can be placed on the grid or maps and alarms are indicated both visually and audibly Radar targets are displayed with persistence tails Configure the Radar Outputs The first step in running the S4 Tech Command and Control C2 application is to configure the radar to send target data to that application This is done in the Outputs tabe of the radar browser page as seen in the figure below Use the settings in the figure to set up radar target data communication to the laptop running the S4 C2 application Make sure that the IP address is set to match that of the laptop DRI Kit v1_manual v1 1 Dy SPO264 QuickStart f Network Outputs Advanced Tre Google Earth kml Timeout 30 B The number of seconds after a track stops before it is cleared from the KML file Generate KML Push Notifications Parameters Add Subscription Updat
Download Pdf Manuals
Related Search