Metered Power Distribution Unit User Guide
Contents
1. Meter 3 digit meter to display current and IP address Function Button e Press and release quickly to turn off the Warning beeps if the Warning threshold is crossed The Overload beep cannot be cancelled e Press and hold the button after 2 beeps the display will show the IP address The octets of the current IP address will flash once across the display the display will then resume showing the current e Press and hold the button after 4 beeps the PDU will switch the method of IP assignment If current method is DHCP then fixed IP will be assumed and vice versa e Press and hold the button after 6 beeps the PDU will be reset to factory defaults Speaker for audible alert e Warning Alert 1 beep 1 second when Warning threshold is crossed e Overload Alert 3 beeps 1 second when Overload threshold is crossed The audible alert will keep beeping until the current goes back 0 5 amps below the threshold value The warning alert can be disabled see instructions on the Function Button above Ethernet Port RJ45 port for connecting to the network Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood 94513 USA 4 Installing the Hardware This section will provide a quick instruction on installing the PDU 4 1 4 2 Important Safety Instructions Check the voltage rating Connect the PDU only to a properly rated power circuit Check circuit load Ensure that connect2. ROCKSOLID Metered Power Distribution Unit User Guide RSM1 15AA 08N1 RSM1 20AB 08N1 RSMo 30AM 16N2 Date 20 January 2012 Revision 03 1 Introduction The Rock Solid Metered Power Distribution Unit PDU is an Internet ready device designed and equipped with a true RMS current meter that will indicate the total power consumption of the PDU The current load can be accessed locally via a digital display or remotely via secure web access Our power monitoring system PDU Utility offers an easy to set up and user friendly computer based utility software for centralized data management of your PDUs This software provides the capability to remotely monitor multiple PDUs and their power consumption to realize the total current power consumption and utilization for your enterprise 1 1 Features of the Built in web server a user can monitor the current consumption of the power distribution unit in real time Built in true RMS current meter and on board display Easy installation and setup SSL support with self signed certificate for secure and encrypted access Audible alarm when the power consumption exceeds user defined warning and overload thresholds Notification via email and or SNMP traps if the power load exceeds the warning and overload thresholds e PDU Utility software for consolidated management SNMP support has SNMP MIB that be monitored by a NMS Per outlet power prote
3. agement Consolidation The data from your Rock Solid PDUs can be consolidated using the PDU Utility software With the PDU Utility software one can e Add PDUs that will have their data consolidated by the PDU Utility e Create groups and add PDUs to the groups e Receive traps and email events from the PDUs e Show consolidated status information for the PDUs Query PDUs for status information threshold crossings etc e Show statistics of power usage and event logs Racks with Rock Solid PDUs installed PC with PDU Utility for consolidated management Network The PDU Utility software is in the USB flash drive that came with your PDU There is a PDU Utility Manual in the flash drive as well in the Manuals directory that will instruct on how to install and configure the software Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood 94513 USA 10 7 Warranty Rock Solid PDUs warrants that all our products will be free of defects in material and workmanship The manufacturer warranty period is 2 years Should any manufacturer defect occur within the warranty period Rock Solid PDUs will correct the defect free of charge with the exception of the cost to ship the product to the factory or authorized dealer that sold the device Proof of purchase in the form of an invoice or prior registration is required to activate this warranty Should any manufacturer defect occur after the warranty p
4. browser You can safely continue and have the browser accept that certificate If you are using Firefox do this by clicking on the Add Exception button click on Get Certificate then Submit Having accepted the self signed certificate you should not get any more warnings going forward and communication with the PDU will now be secure 5 4 Changing Network Parameters To change network parameters do the following 1 From the main menu click on the Network link 2 Enter anew hostname optional 3 If not acquired by DHCP enter a new IP address 4 Enter a subnet mask 5 Enter a default gateway 6 Disable DHCP and or add DNS servers optional Once you apply the changes you may have to change the URL in your browser and log back in to continue Warning When configuring the network parameters for your PDU it is recommended that the power monitoring network system be isolated from your main data network This ensures access to your power equipment in the event of main data network failure Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood CA 94513 USA 5 5 Checking the PDU Load The total input load in amps is shown at the top of the screen under the Rock Solid logo Clicking on the PDU link off the main menu also shows the PDU input load and the current threshold values 5 6 Checking and Changing System Parameters Clicking on the System link off the main menu displays t
5. cable Configure your computer to be on the same network as the PDU example IP 192 168 0 1 With the IP 192 168 0 216 as the URL use your browser to connect to the PDU Use the credentials username snmp and password 1234 to log in to the PDU ee 5 2 Changing User Credentials Once you are logged in change the user s login and password We highly recommend changing the default username and password leaving it would create a serious security flaw To change the credentials 1 Click on the User link 2 Enterthe old username and password 3 Below that enter the new username and password Make sure you do not forget the new credentials or you will be locked out and will have to reset the PDU to factory defaults if you do so 4 Click on Apply Login again to continue PDU configuration Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste 1 1 Brentwood CA 94513 USA 5 3 Enabling SSL Access To enable SSL access 1 Click on the SSL link on the main menu 2 Check the Enable SSL checkbox Enter the credentials of the PDU user to activate 4 Click on Apply You will hear the box beep once and the SSL light go on You may also get a message Connection to demo box lost you can safely click it away and ignore that message 5 You will have to log back in Add https to the url and log back in Since the certificate is self signed you will get a warning message from your
6. ction by the circuit breaker 1 2 Voltage and Current Ratings e Voltage Input 100 120V Voltage Output 115V Max Current Rating 5 15 8 15 max current rating RSM 20AB 08N1 20 max current rating RSM 30AM 16Nz2 30A max current rating Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood CA 94513 USA 2 Package Contents The standard PDU package contains a Power Distribution Unit with supporting hardware and software The package contains Power Distribution Unit Quick Start Guide Power Cable 2 Rack mount Brackets and 8 Screws USB Flash Drive containing o User Manual PDU Utility Software SNMP MIB Management Information Base PDUMIB mib Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood 94513 USA PDU Functions The PDU functions for the model 5 1 15 8 are shown below the functions for the 20 10 metered PDU and the 16 output PDUs are also similar Y Circuit breaker for Metered models this is next to the display For overload power protection press to reset if it is tripped Power outlet receptacle Connect to your equipment Yellow SSL LED Indicator Light on means web access is protected by SSL Green DHCP LED Indicator Light on means PDU gets IP address via DHCP Green Power Output Indicators not on the Metered models
7. eriod Rock Solid PDUs will correct the defect and apply a fee for the labor and parts to repair the defect 7 1 What this warranty does not cover 1 Shipping damage after unit is accepted from courier 2 Damage to the device due to opening rough handling or misuse of the device 3 failure loss damage or personal injury due to accident neglect abuse by the consumer improper operation 4 unit purchased from an unauthorized dealer If the original factory serial number has been removed defaced replaced or tampered with in any way 6 Transportation charges to the factory or authorized dealer incurred in connection with warranty service 7 Indirect consequential or special damages except as required by Federal or State laws If the device has a manufacturer s defect please contact sales remotepowergear com to get an RMA document to fill out and return with the device Any devices returned without an RMA document will be rejected WARNING Opening the device cover during the warranty period voids the warranty Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood CA 94513 USA 11
8. he system parameters The model name firmware version MAC address SNMP System Name SNMP System Contact and SNMP Location are shown The SNMP values can be changed by doing the following 1 From the main menu click on the SNMP link 2 Enter System Name 3 Enter System Contact 4 Enter Location 5 Click Apply A confirmation dialog box will pop up click OK to save the new values 5 7 Checking and Changing the Threshold Values The PDU has 2 threshold values the Warning threshold and the Overload threshold values If the input current crosses the Warning threshold then the PDU will beep with the frequency 1 beep per second If the input current crosses the Overload threshold then the PDU will beep with the frequency 3 beeps per second The audible alert will keep beeping until the current goes back 0 5 amps below the threshold value The Warning alert can be manually disabled see instructions on the Function Button The Overload alert cannot be manually disabled To change the threshold values do the following 1 From the main menu click on the Threshold link 2 Enter the new Warning and Overload values 3 Click Apply A confirmation dialog box will pop up click to save the new values Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste 1 1 Brentwood CA 94513 USA 5 8 Checking and Changing the Mail Settings When an event example crossing of threshold occurs the PDU can se
9. ion to the power circuit will not cause overloading of the circuit or supply wiring Do not use this PDU in conjunction with a power strip or other PDU in an attempt to branch the power circuit The power rating for equipment connected to the outlet power of the PDU should not exceed individual outlet load rating Check rack ambient temperature If installing in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than ambient temperature in the room Ensure that the rack ambient temperature does not exceed the maximum rated temperature of the equipment Check air flow Ensure that there is adequate air flow in front and behind the PDU when installing in the rack Check mechanical load Mounting of the equipment in the rack should be such that a hazardous condition is not created due to uneven mechanical loading Ensure reliable grounding Do not connect to any ungrounded outlet or extension cords adapters that remove grounding Ensure proper use Do not use this equipment in life support applications where failure of the equipment may result in failure of the life support systems Ensure indoor installation Do not install in areas of excess moisture dust or direct sunlight No user serviceable parts Do not drill into the PDU housing or open the housing in an attempt to service the PDU Do not modify the input plug or power cable Install wisely Do not attempt install during a thundersto
10. nd out an email message to a pre defined email account To configure the mail settings do the following 1 From the main menu click on the Email link 2 Enter Email Server The Email Server is the proxy email server that will be used to send the email The Email Server cannot be an IP address only a hostname that is resolvable by the DNS servers configured earlier is valid Enter the Sender s Email Address This is the email address of the sender 4 Enter the Recipient s Email Address This is the destination email address Click Apply A confirmation dialog box will pop up click OK to save the new values The message in the email will be formatted as follows Indicate OutletA H XXXXXXXxX status in order means the power off X 1 means the power on 5 9 Checking and Changing the SNMP Trap Parameters When an event occurs the PDU can send out trap message to pre defined IP address To configure the SNMP settings do the following 1 From the main menu click on the SNMP link 2 Enter Receiver IP The Receiver IP is the IP of the server that will receive the SNMP trap Enter Write Community Default Write Community is public and can be modified by user 4 Click Apply A confirmation dialog box will pop up click to save the new values Read Community is public and fixed Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood CA 94513 USA 6 Power Man
11. rm Mounting the PDU To mount the PDU onto a server rack perform the following instructions 1U PDUs only Attach the mounting brackets to the unit using the 4 retaining screws provided for each bracket Choose a location for the PDU on your rack Align the mounting holes of brackets with the holes on the vertical posts of the rack Secure the PDU on the rack with rack screws Connect input power to the PDU with the provided power cable Connect your equipment to the output power sockets on the PDU Connect the PDU to your network system using an Ethernet cable Switch on the PDU Rock Solid Metered PDU Manual GS Geiger Group 181 Sand Creek Rd Ste l 1 Brentwood CA 94513 USA 5 Configuring the PDU 5 1 Logging onto the PDU The PDU can acquire an IP address using DHCP or failing that will set the static IP 192 168 0 216 If your network has a DHCP server follow the Using DHCP instructions below to log in to the PDU else follow the instructions in the Using the default IP section 5 1 1 Using DHCP 1 Hold the Function button down and release after 2 beeps 2 The PDU meter will display the octets of the current PDU IP address in sequence 3 Use your browser to connect to the PDU enter the PDU IP address as the URL 4 Use the credentials username snmp and password 1234 to log in to PDU 5 1 2 Using the Default IP Connect your computer directly to the PDU with an ethernet
Download Pdf Manuals
Related Search