Setup Guide - LifeShield, Inc.
Contents
1. Life S EC URI T Y Li WELCOME TO LIFESHIELD Thank you for choosing LifeShield as your home security system We take the safety of your home and family very seriously and we are committed to giving you a fantastic customer experience LifeShield was started as a way for consumers to have state of the art home protection at an affordable cost Today we re one of the fastest growing security companies in the industry At LifeShield we pride ourselves on always being technologically ahead of the curve In fact we were one of the first companies to offer free apps for every mobile platform Now with LifeView our full featured mobile interface we ve put complete control of your security system in your hands You won t find anything like it at any other security company LifeView allows you to instantly arm and disarm your system change your system settings store video or still images from your security camera find out your home s current safety grade and so much more We encourage you to log in to LifeView as soon as you get your system set up so you can start exploring these and other amazing user friendly features This guide will walk you through the easy set up of your LifeShield system We ve already customized and tuned your system to your specifications so everything should be ready to go when you open the box As soon as you re finished setting up your system it s time to register with LifeView Again2. Micro SD Slot or green wire connector a 0 reset insert paperclip into reset button next to power connector for at least 5 seconds and release Add Handset if included Install the Handset and Charger INSTALL BATTERY PACK N Open the Battery compartment INSTALL D BATTERY PACK i 4B Insert the Battery plug into the two pin jack Lu and insert the Battery Replace the Battery cover NOTE USE ONLY THE LIFESHIELD LS80 BATTERY PACK ADD THE HANDSET Attach Belt Clip Snap the Belt Clip onto the sides of the Handset CONNECT THE CHARGING CRADLE Connect the Charging Cradle power adapter to the bottom of the Charging Cradle and to the electrical wall outlet CHARGE THE HANDSET Place the Handset in the Charging Cradle When properly seated on the cradle the amber light on the front of the cradle will be illuminated NOTE Immediately place the Handset in the Charging Cradle that came packed with the Handset THE HANDSET MUST BE CHARGED FOR AT LEAST 30 MINUTES PRIOR TO ATTEMPTING ANY SECURITY SYSTEM INSTALLATION IT MUST BE CHARGED FOR 2 HOURS BEFORE MAKING PHONE CALLS NOTE THE PHONE SYSTEM COMES WITH VARIOUS SETTINGS PRE DEFINED FROM THE FACTORY SHOULD YOU WANT TO CHANGE THESE SETTINGS WE SUGGEST WAITING UNTIL AFTER YOU ACTIVATE YOUR SYSTEM THESE SETTINGS INCLUDE RING TONES RING VOLUME DISTINCTIVE RINGING DISPLAY CONTRAST ETC ADD THE HANDSET TO Y
3. here then proceed to Step 2 Qa Connect Base Home Essential Kit i Crece CU Optional Phone Cord Put the Base near your Modem Router Remove the stand by sliding the Table Stand downward from the main body of the Base Insert the battery then replace the Table Stand by sliding upward onto the main body of the Base Insert the power adapter plug fully into the D jack on the back of the Base Then plug the power adapter into the wall outlet Connect the Ethernet Cable between an available port on your router and the back of the Base Continue to Step 2 OPTIONAL IF YOU CONNECT A PHONE CORD FROM THE SYSTEM BASE TO A TELEPHONE WALL JACK YOU LL HAVE A BACK UP PATH FOR ALARM COMMUNICATIONS IF YOUR INTERNET CONNECTION ISN T FUNCTIONING dar Ut Connect Cellular Gateway Home Essential Kit Celluar Ready unu ele ee lUlal Ready Kit start here then proceed to Step 2 Cellular Gateway For ideal reception put the Cellular Gateway near Back View an outside wall outlet on a high floor in your home Remove the back cover of the Cellular Gateway Plug the battery pack into the plug receptacle and insert the battery into the battery compartment Battery Replace the back cover Pack Plug the Cellular Gateway into the lower electrical outlet with the tab facing upward B D D E F Continue to Step 2 GQVAHV dl4S LON Oa 3d80 LOVXA NI SdjALS MOTIO4 LNV
4. light rapidly flashes The following messages will appear on the Handset or Console when the system has found and added the Grid Extender Press OK when you have been informed that the GX has been added You will then be given the option to edit the default name Use DELETE to erase the current name and replace with new text by using the keypad 5 000 9 9 9090909 Press OK when editing is complete NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK 14 a Add Smoke Sensor if included INSTALL SMOKE SENSOR N Remove the Smoke Sensor and related components from the box and physically install the device according to the manufacturer s printed instructions NOTE It is important to follow the manufacturer s printed instructions regarding placement of the device location installation mounting and battery activation including removal of the battery tab insulator paper prior to moving on to the next step involving integration of this device with your LifeShield System Once the mounting bracket is secured to the ceiling attach the Smoke Sensor into it ADD THE SMOKE SENSOR TO THE LIFESHIELD SYSTEM On the Handset or Console press MENU Scroll to Security Setup press SELECT and enter the Master Code Scroll to Sensors press SELECT Scroll to Add New press SELECT Scroll to Smoke Sensor press SELECT 500 090 009 Following the instructions di
5. system If there are no confirmation beeps check to make sure that the battery insulator tab has been removed and repeat the steps above Once the Glassbreak Sensor has been added to the LifeShield system Use the Edit feature to rename the device if desired Press DELETE to erase text and the keypad keys to type new ones e Press OK then press BACK until the Main Menu is displayed Shut the front cover of the Glassbreak Sensor TEST THE GLASSBREAK SENSOR On the Handset or Console press MENU Scroll to Utilities press SELECT Scroll to Test press SELECT Enter your Master Code Select System Test Press the SKIP soft key to skip the Siren Test Press the OK soft key on next screen for Starting Comm Test Scroll to the name of the Sensor that you would like to test and press SELECT 5000000009 Tap strongly on the front cover of the Glassbreak Sensor If the Glassbreak Sensor test is successful the LCD screen will display Sensor xxx Passed If these words do not appear return to Add the Glassbreak Sensor to the LifeShield System NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK Add Grid Extender if included DETERMINE THE LOCATION Place the Grid Extender in a location that is soread apart from the Console and Base A second floor location is a great place to install this if you choose Having these devices spread throughout the home will maximiz
6. thank you for becoming a LifeShield customer We will continue to do everything we can to make sure you your home and your family are safe Sincerely Ju K DAZ A Sil Mike Hagan Louis Stilp President amp CEO Founder LifeShield Inc LifeShield Inc MASTER CODE Component Placement Suggestions The LifeShield home security system you are about to set up is wireless To maximize wireless coverage plan to place the components throughout your home Ideally these components will be in different rooms on interior walls A key consideration is making sure that all Sensors are within approximately 30 feet of one or more of the main components base cellular gateway console NOW IS A GOOD TIME TO PLAN YOUR COMPONENT PLACEMENT SYSTEM COMPONENTS INCLUDED WITH BOTH KITS HOME ESSENTIAL KIT AND HOME ESSENTIAL KIT CELLULAR READY BASE HOME ESSENTIAL KIT ONLY The Base connects your LifeShield system Put the Base near your Internet modem router and near a wall outlet KEYCHAIN REMOTE O R CELLULAR GATEWAY HOME ESSENTIAL KIT T CELLULAR READY ONLY The Cellular Gateway connects your LifeShield system and the monitoring center via cellular network CONSOLE Put the Cellular Gateway near an outside SENSOR MAGNET wall outlet on a high floor in your home and the monitoring center via the Internet GQVAHV dl 4S L NOG did8o LOVXA NI SdidlS MO1104d LNVLYOdWI gt Home Essential Kit start
7. then press BACK until the Main Menu is displayed Re attach the Front and Back Covers of the Motion Sensor NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK Tape For Top Corner Mount 2 a Bottom 8 Qa Add Siren Detector if included The Siren Detector works with your existing hazard detectors smoke fire alarms carbon monoxide detector or both to send a signal to the monitoring center whenever your hazard detector sounds Mount the Siren Detector no more than 4 away from the targeted hazard detector For more product details and full specifications see the User s Manual or the Siren Detector Device Guide N Remove the Installation Template on the bottom of the Siren Detector box Place next to the existing hazard detector Figure B so the large curved side of the template rests against the outer edge of the hazard detector Using a pencil or pen mark the location of the two screw hole openings in the template on the ceiling These marks will be used as a mounting location reference Turn the Siren Detector over and press the Bracket release tab while gently pulling the bracket away du from the device Attach the Siren Detector Bracket to the ceiling using either double sided tape or the provided screws and wall anchors Be sure the arrow on the inside of the bracket faces the hazard detector D Turn the Siren Detector over and locate the battery insu
8. to LifeView Application with your Username and Password 2 Click Stay 5 Enter Master Code Away Arming Leaving Your Home If you re going to leave your home even for a quick run to the store or if no one is at home arm the system using the AWAY key It will provide an audible Exit Delay The Exit Delay beep will increase in frequency during the last 10 seconds of arming You can arm your system using one of the 4 devices Console Keychain Remote LifeView Web Application and LifeView Mobile Applications TO ARM Using the Console 1 Press AWAY on your Console and enter your Master Code 2 The system is armed when the Exit Delay has expired Note If a door doesn t open and close during the exit delay the system will automatically switch the arming mode to STAY Using the Keychain Remote 1 Press and hold AWAY on the Keychain Remote for 2 seconds 2 The system will respond with a light blink and beep letting you know the system is armed Using the LifeView Web Application 1 Login to LifeView Application with your User Name and Password 2 Click Arm Away Using the LifeView Mobile Application 1 Login to LifeView with your Username and Password 2 Click Away 5 Enter Master Code 19 NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK ARMING YOUR SYSTEM CONTINUED Instant Arming staying Home for the Evening When you and the family are in for the night wa
9. 5 feet for both coverage and pet immunity purposes M Apply the 3M adhesive tape in the locations shown in Figure D for corner mounting or wall mounting A The rounded end of the Motion Sensor that has the release tab is the bottom of the sensor which should be closest to the floor when installed properly Add Additional Motion Sensors On the Handset or Console press MENU Scroll to Security Setup press SELECT Enter the Master Code M Scroll to Sensors press SELECT Scroll to Add New press SELECT Tape For Scroll to Motion press SELECT Wall Mount wee Following the instructions displayed on the LCD screen Wait 5 seconds If the display reads Un clip Sensor from Bracket insert the battery into the Motion Sensor If the display reads Insert Battery insert the battery into the Motion Sensor observing correct polarity as shown in Figure B You will have 30 seconds to complete this step When the Motion Sensor has successfully been added you will hear 4 fast confirmation beeps from the LifeShield system If there are no confirmation beeps remove the battery from the Motion Sensor then re insert the battery into the Motion Sensor to cause another power up registration message to be sent Once the Motion Sensor has been added to the LifeShield system Use the Edit feature to rename the device if desired Press DELETE to erase text and the keypad keys to type new text AA Press OK
10. 67 860 2398 It s very important to obtain permits and or registration if required in your municipality PLEASE NOTE RESIDENTS ARE RESPONSIBLE FOR ANY PERMIT FEES FALSE ALARM FEES RUNNER SERVICE FEES AND OTHER APPLICABLE FEES IF INCURRED Many municipalities will not allow LifeShield to begin monitoring your home without a permit In the event of a false alarm municipalities can charge fines to consumers who do not obtain the required permits registration Also some police agencies will not dispatch to a home that isn t registered permitted Please contact your local municipality as soon as possible to begin the necessary processes that may be needed in your area WE RE SOCIAL ARE YOU f c Check us out on Facebook Follow us on Twitter https www facebook com wirelessalarmsystem http twitter com LSHomeSecurity o 2 Join our circle on Google Check us out on Pintrest http gplus to lifestylenomesecurity http pinterest com lifeshield YOU COULD WIN For more details please visit FREQUENTLY ASKED QUESTIONS 1 Where do find instructions on adding additional components to my LifeShield system Once you have your system set up you may find you re interested in expanding it That s easy to do If you re interested in adding a Glass Break Sensor Water Sensor or other LifeShield compatible component to your system you can refer to the instructions in the device guide inside each individual product b
11. EVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK Add Water amp Temperature if included INSTALL THE SENSOR N Locate the Honeywell 5821 red and white box and remove the white wireless transmitter from the box B Using a flat object such as a screwdriver pry off the top cover of the transmitter and set aside Press down on the mounting plate bracket release tab to remove slide off the mounting plate Place the mounting plate aside D Reference the table below to determine the desired sensing type Hot Temp Cold Temp Warm Temp or Flood water Using the tip of a paperclip Cor similar object push the white D sliding buttons of the DIP switch see Figure A into the configuration that corresponds to BN peo eee o the desired sensing type fel S ae Follow the appropriate steps associated with the sensing type of the Sensor en e above ss 5 pop s nsin or moret an or moret an a Temperature Sensor Hot Warm or Cold sensing Locate the mounting bracket where it will i ae uS be most suitable for Temperature Sensing for example on a wall ceiling etc Using either vL pum Ito the supplied screws or double faced adhesive tape secure the mounting bracket to a flat sensing Mz fem des p su rface wall Or cel ng Flood E External probe tips External probe tips Water U are in contact with have been out of REQUIRED j sensing water for m
12. LYOdNWI DOO O90 G M Connect Console Put the Console near a frequently used door ideally in a different room than the Base Cellular Gateway BUT NO MORE THAN 100 FEET FROM THE BASE CELLULAR GATEWAY Remove the battery compartment door Plug the battery pack into the plug receptacle and insert the battery into the battery compartment Snap on the battery compartment door Connect power adapter to the back of the Console Route the power adapter cord through the channel toward the top of the Console Snap the table stand provided in the kit onto the back of the Console Plug the power adapter into nearby electrical wall outlet that is not controlled by a switch Wall Mounting To mount the Console to a wall complete the following steps am 909 5 9009 Select a wall location and use the mounting plate as a template for marking the wall for placement NOTE TO MOUNT THE CONSOLE ONTO AN EXISTING TELEPHONE WALL PLATE NOT INCLUDED BEGIN AT STEP D Drill 5 16 holes and insert drywall anchors provided into the holes Screw the mounting screws into the anchors leaving the screws heads exposed approximately 3 8 may require adjustment to achieve a tight fit Connect power adapter to the Console Route the power adapter cord through the channel of the wall mounting plate Slide the Console with mounting plate onto the wall screws or phone mounting plate Plug the power adapter into nearby e
13. OUR LIFESHIELD SYSTEM Follow these steps for adding an additional Handset to a LifeShield system Handsets packed with kits are pre registered and do not require these steps After the initial installation of the LifeShield System devices may be added to enhance Device System access or performance faci MERE The maximum number of devices that can be added to a LifeShield System is shown Ps in the table to the right After the Handset and Charger are installed use a Handset 4 8 or Console that is already registered on the System to add the new Handset ADD THE HANDSET On an Existing Handset or Console use the SCROLL and SELECT buttons to The system will allow a maximum of 8 Handset Console navigate to GC or Handset Menu Security Setup GCs or Handset Add New or Grid Extender combinations Press the SELECT key to Add New The system will begin searching for a new Handset On the new Handset press the SEARCH key The system display and audio signal will inform you the Handset is found You will then be given the option to edit the default name 9e0e09 Use DELETE to erase the current name and replace with new text by using the keypad NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK 12 13 al Add Glassbreak Sensor if included INSTALL GLASSBREAK SENSOR N Remove the Glassbreak Sensor and related components from the box and physically install the
14. S Vi p m Z S Magnet Spacer Bracket Spacer Sensor Bracket Magnet Magnet Tape Bracket Tape optional use optional use If you would like change any of the preprogrammed sensors see Step 4 6 or Add Additional Sensors If you would like to change any of your preprogrammed sensors you can Just follow the steps below TO CHANGE PREPROGRAMMED SENSORS 5090000 Press MENU on Console Scroll to Security Setup on the screen press SELECT Enter Master Code found in the front cover of this book Scroll to Sensors Select sensor to be modified Use menu to select and change sensor attributes TO ADD ADDITIONAL SENSORS ae Remove the battery tab by squeezing and holding the metal spring clip where the REMOVE tab folds around battery The battery will spring upward Carefully remove the insulating tab from under the battery then gently press the battery back into the spring clip For this step you will need your Console and Sensor Using Console D 9900000 D O m Press MENU Scroll to Security Setup press SELECT Enter Master Code found in the front cover of this book Scroll to Sensors press SELECT On Add New press SELECT Scroll to the type of Sensor Open Close press SELECT Wait 5 seconds before clipping the Sensor into the Bracket You will then have 30 seconds to complete the setup Clip the Sensor into the Bracket The Console will beep when the system finds the Sensor This may
15. View Portal so the system does not expect normal phone line signals LifeShield recommends a telephone line for the voice functionality of the Console and for redundant backup communications to the monitoring center in case there s ever an interruption to your broadband connection 7 What if have VoIP LifeShield is VoIP compatible with most modems Note The system will not work with Magic Jack Your VoIP modem telephone line can plug into your LifeShield system 8 What if have DSL LifeShield is DSL compatible An Ethernet cable may be connected between your LifeShield system and your home router which in turn connects to your DSL modem A telephone cord may then be connected between a telephone jack in your home and your LifeShield system so long as a DSL filter is installed into this connection A DSL filter allows you to use the Console by preventing static from your DSL NOTE If you have DSL you should use a DSL filter on all of your home telephones to prevent this type of interference 9 Will LifeShield cause interference with other RF products like my wireless network Wi Fi LifeShield uses advanced radio frequency technology to avoid interference with other devices 10 What if there is no telephone line near my broadband connection The LifeShield system can be connected to the telephone line from the Base or Console Therefore it is not required to have a telephone line near your broadband connection 11 How many Bases a
16. device according to the manufacturer s printed instructions NOTE It is important to follow the manufacturer s printed instructions regarding a connecting the batteries b adjusting the sensitivity c selecting the location and d mounting the device prior to moving on to the next step involving integration of this device with your LifeShield system Please note that it is not necessary to Enroll the device at this time Mount the Glassbreak Sensor to a flat surface and close the front cover ADD THE GLASSBREAK SENSOR TO THE LIFESHIELD SYSTEM NOTE A LifeShield system including a Base and at least one Handset or Console must be installed before a Glassbreak Sensor can be added Starting with the Glassbreak Sensor mounted to a flat surfacewith the front cover closed On the Handset or Console press MENU Scroll to Security Setup press SELECT and enter the Master Code Scroll to Sensors press SELECT Sensor Found Sensor Added Edit Name Scroll to Add New gt press SELECT Please Wait Sensor 1 e 30 seconds E Scroll to Glassbreak press SELECT CANCEL CANCEL OK DELETE OK T Following the instructions displayed on the LCD screen NOTE WAIT 5 SECONDS THEN OPEN THE FRONT COVER OF THE GLASSBREAK SENSOR UN CLIP SENSOR FROM BRACKET CYOU WILL HAVE 30 SECONDS TO COMPLETE THIS STEP When the Glassbreak Sensor has successfully been added you will hear 4 fast confirmation beeps from the LifeShield
17. e system coverage A power outlet is required to operate the Grid Extender INSTALL THE GRID EXTENDER N Install Battery Pack Open the Battery compartment 1 Insert the Battery plug into the two pin jack and insert the Battery 2 Replace the Battery cover 4B Plug the Grid Extender into the electrical wall outlet ADD THE GRID EXTENDER TO YOUR LIFESHIELD SYSTEM Follow these steps for adding an additional device to an existing system Devices packed with kits are pre registered and do not require these steps After the initial installation of the LifeShield System components may be added to enhance access or performance The maximum number of devices that can be added to a LifeShield System are Device System The system will allow a maximum of 8 Handset Console or Grid Extender combinations Extenders GX Found After the hardware is installed use a Handset or Console that is currently Please wait registered on the System to follow the steps for adding the Grid Extender b0 Seconds Flashing Light After installing the hardware enter MENU on your Handset or Console ii Scroll to Security Setup and press SELECT Enter Master Code Add Button GX Added Scroll to GCs or Handsets and press SELECT Press the SELECT key to Add New The system will begin searching aca CANCEL OK for the new Grid Extender you are adding On the Grid Extender press and hold the center button until the green
18. een will display Sensor xxx Passed If these words do not appear return to Add the Sensor to the LifeShield System TESTING AS A FLOOD WATER SENSOR On the Handset or Console Press MENU Scroll to Utilities press SELECT Scroll to Test press SELECT Enter your Master Code Select System Test Press the SKIP soft key to skip the Siren Test Press the OK soft key on next screen for Starting Comm Test Scroll to the name of the Sensor that you would like to test and press SELECT 5000000009 Place the Water Probe directly into water or alternately place a piece of wet cloth between the probe legs and wait at least three 3 minutes TESTING AS A TEMPERATURE HOT COLD WARM SENSOR The temperature sensing aspects of the Honeywell Model 5821 can be tested in the same manner as above with the use of specialized equipment that is capable of increasing or lowering the ambient temperature in the environment surrounding the Sensor as needed to result in activation c Add Water amp Temperature cont if included Note Do not re attach cover until you have added this device to the LifeShield System NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK SETUP COMPLETE Using Your LifeShield Security System Now that you ve set up and activated your system you have a chance to find out how LifeShield can fit into your everyday life You can access your secur
19. er LED to stay solid B On console select Menu gt Cameras gt Add New Once all cameras are found press OK M Log in to LifeView and select Camera gt Camera Settings gt Edit A Enter SSID or Network Name wireless connection security type and password Entries are case sensitive spelling and spacing must be exact amp Once Wifi information has been saved wait 2 minutes before unplugging the power and then Ethernet p After 2 minutes plug power back into camera and leave Ethernet unplugged Once power light is solid the camera is wireless and ready for final placement If the camera works while connected to the Ethernet but not wirelessly then the WiFi information must be verified Repeat step D if necessary ITT NOTES Must be on same router as your LifeShield Base to setup After setup plug into power where you like Setup WiFi using camera Settings in LifeView disconnect Ethernet cable then remove and reconnect the power Setup alerts in LifeView to take pictures when sensors tigger Live video per session is 5 minutes If the camera works while connected to the Ethernet but not wirelessly then the WiFi information must be verified Repeat step D if necessary Wireless or WiFi technology allows an electronic device to exchange data wirelessly using radio waves over a computer network p RESET n Add Indoor Camera Model RC8221 if included DO NOT use the WPS Button
20. feShield aO Ready To Arm PHNBK Thu 2 8 11 48a E E o CANCEL OFF o Oooooooo Oooooooo Oooooooo INSTANT o Oooooooo STAY O ooooooo m e On Ooooooo C 9 G969 2 9 Zz g PANIC Oooooooo u ES Scroll Buttons YO Scroll Buttons B NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK a Place Preprogammed Motion Sensor if included Prepare Motion Sensor B N Separate the Front and Back Covers of the Motion Sensor by pressing the E e Battery tab with your finger or the top of a pen Figure A Insert the battery LUN A OS N Select the desired sensitivity As shown in Figure B place the jumper over m oY both pins for Normal Sensitivity or place the jumper over just one pin for High Sensitivity In most cases Normal Sensitivity is the recommended setting This can always be changed later if your experience shows the Normal is not meeting your needs Press Place the Motion Sensor Sensitivity Place the Motion Sensor following the location Jumper recommendations check marked locations shown in Figure C Avoid the example locations marked with the X which are aug household areas that typically cause false alarms such as heat air conditioning fans or direct sunlight The recommended mounting height is 7
21. he Contacts is reached they will be asked to provide the Monitoring Password that you created during your initial setup of your account This is NOT your Master Code which is located in your Quick Setup Guide d If the incorrect Monitoring Password is provided the monitoring center will not inform you and will automatically dispatch the authorities If the correct Monitoring Password is given then the monitoring center will act as directed by the Contact 5 WATER amp TEMPERATURE You may configure your system so that you will receive notifications when the sensor is triggered The default setting is an email notification and a call from the monitoring center You may alter the setting to include a text message Local Permit and Registration if applicable To activate the monitoring service for your home security system you may need to obtain a permit and or registration from your municipality To find out more about any necessary permits all you have to do is follow these simple directions Obtaining Local Permits and Registration 1 Contact your local municipality and ask if a permit is required for home security systems If so find out exactly what s required Below are a few things they may ask you for Alarm Company Monitoring Company LifeShield Inc Security Monitoring Services Inc 2021 Cabot Blvd West 715 West State Road 434 Suite J Langhorne PA 19047 Longwood FL 32713 Phone 267 907 9779 Phone 855 894 1737 Fax 2
22. it feature to rename the device optional NOTE PRESS DELETE TO ERASE TEXT AND USE THE KEYPAD KEYS TO TYPE IN A NEW NAME ONCE YOU ARE SATISFIED WITH THE ENTERED NAME PRESS OK Scroll down to select the type of hazard detector to which this Siren Detector will be associated SMOKE FIRE CARBON MONOXIDE or BOTH and press SELECT NOTE Not all smoke carbon monoxide detectors are compatible with the siren detector If the siren for your current smoke carbon monoxide detector sounds for 30 seconds and there is no pause in the siren the Siren Detector should operate as intended IMPORTANT THE SELECTION YOU MAKE DURING THIS CONFIGURATION STEP WILL DETERMINE THE TYPE OF MESSAGE THAT IS SENT TO THE MONITORING CENTER M Press OK to return to the Main Menu NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK 9 See the User Manual for more detailed instructions and information about testing the Siren Detector al Add Outdoor Camera Model OC810 if included The OC810 is an outdoor camera with built in Infrared LEDs for night vision TO USE N First plug Ethernet cord into camera and router Wait for Power LED to stay solid On console select Menu Cameras Add New Once all cameras are found press OK M Log in to LifeView and select Camera gt Camera Settings Edit A Enter SSID or Network Name wireless connection security type and password Entries are case sen
23. ity system from your Console Keychain Remote LifeView web application or LifeView mobile applications Using Your System Arming your system p 19 amp 20 Disarming your system p 20 Panicking your system p 20 Responding to an alarm p 21 UN DOWNLOAD THE FREE LIFEVIEW MOBILE APPS SO YOU LL ALWAYS HAVE ACCESS TO YOUR SYSTEM NO MATTER WHERE YOU ARE D ownload LifeView for Download LifeView for Android Apple iPhone ARMING YOUR SYSTEM stay Arming Home During the Day Maybe you work at home or you re taking care of the kids during the day This is the setting you want to use on your LifeShield system By activating Stay Arming the system will ignore certain Sensors like the Motion Sensor and Sensors on interior doors Arm the system using the STAY key A silent Exit Delay and an audible Entry Delay is provided You can arm your system using one of the 4 devices Console Keychain Remote LifeView Web Application and LifeView Mobile Applications TO ARM Using the Console 1 Press STAY on your Console and enter your Master Code 2 The system is armed when the Exit Delay has expired Using the Keychain Remote 1 Press and hold STAY on the Keychain Remote for 2 seconds 2 The system will resoond with a light blink and beep letting you know the system is armed Using the LifeView Web Application 1 Login to LifeView with your User Name and Password 2 Click Arm Stay Using the Mobile Applications 1 Login
24. lator tab by pulling it straight out o Discard the tab Existing Hazard Dectector NOTE AFTER REMOVING THE TAB PRESS DOWN ON THE TOP OF THE BATTERY TO BE SURE IT HAS NOT BEEN DISLODGED Align the Siren Detector with the Bracket and snap it on Installation Template Add Siren Detector Once the Siren Detector has been mounted it must then be added to the LifeShield System For this step you ll need your Console Press MENU on Console Scroll to Security Setup press SELECT Enter the Master Code Scroll to Sensors press SELECT Scroll to lt Add New gt press SELECT Scroll to Siren Detector press SELECT 5900000 Following the instructions displayed on the Console Wait 5 seconds then press the button on the Siren Detector NOTE ONCE THE SIREN DETECTOR IS FOUND YOU LL HAVE TO DO AN AUDIO TEST TO BE SURE IF THE SIREN FROM THE TARGET HAZARD DETECTOR CAN BE DETECTED BY THE SIREN DETECTOR Following the instructions displayed on the Console press the test button on the hazard detector until the Console displays Siren Detector Added which indicates that the test has passed If the test does not pass within 1O to 12 seconds of the siren sounding the hazard detector may not meet the requirements described earlier and may need to be replaced If the test fails the LifeShield system will not permit the Siren Detector to be added z M Once the Siren Detector has been added to the LifeShield system use the Ed
25. lectrical wall outlet that is not controlled by a switch Battery Compartment Power Cord Table Stand Mark Spot On The Wall Optional Connect to the telephone line here not included Your Console has been preprogrammed with your system No additional steps are necessary Place Preprogammed Sensors There are up to 2 preprogrammed sensors Main Door e Window 1 NOTE THESE TWO SENSORS HAVE UNIQUE PROPERTIES BUILT IN THE MAIN DOOR HAS AN ENTRY DELAY OF 30 SECONDS AND AN EXIT DELAY OF 60 SECONDS WINDOW 1 HAS AN ENTRY DELAY OF O SECONDS M Once you have determined the appropriate location and orientation for the Bracket and Magnet attach them with double sided tape NOTE WHEN POSSIBLE PLACE THE BRACKET ON THE STATIONARY FRAME OF DOOR OR WINDOW AND PLACE THE MAGNET ON THE DOOR OR WINDOW ITSELF Various orientations between the Bracket and Magnet may be used Window Mounting as long as 5 4 distance is not exceeded See Example in Figures 1 4 NOTE SPACERS IN BOTTOM TRAY MAY BE USED ON THE BRACKET OR MAGNET TO ADJUST ALIGNMENT Bracket Magnet 3 4 spacing Bracket Magnet c O NE E d Door Mounting d o L l JE Figure 1 Figure 2 Figure 3 Figure 4 Level Orientation Angled Orientation Perpendicular Orientation Perpendicular Orientation KIT C ONTENT
26. ment A 50 restocking fee and shipping charges will be deducted from the amount refunded Returns must be postmarked by and received in our warehouse within 20 calendar days of the issuance of the RMA number All products must be packed in the original unmarked packaging including any accessories manuals stickers signs documentation and registration that shipped with the product and the products must be in new resalable condition Incomplete missing or damaged products not in resalable condition or products not meeting the return guidelines outlined in your product service agreement will be subject to MSRP charges No returns will be accepted without an RMA number Please allow an estimated 14 calendar days after receipt of your package for refunds to be credited to the original purchasing credit card 3 Do have to purchase service with my LifeShield system Yes The LifeShield system will not operate without monitoring service LifeShield offers several service plans 4 How do cancel service Service may be cancelled by calling LifeShield Support at 1 888 885 6070 Service may not be cancelled via email 5 Is there an early termination fee if cancel service Your contract terms are set at the time of purchase There will be a termination fee for early cancellation 6 Do I have to have a landline phone to use LifeShield No telephone lines are optional If you don t have a telephone line you must change a system setting in the Life
27. nd Consoles can have in my system The system supports 1 Base and 4 Consoles 12 How many sensors can I have in my system The LifeShield system can support the use of up to 50 sensors of any type 13 Are there special licenses needed to install a security system No special licenses are required to install a system in your home However be aware that some municipalities require a monitoring permit for police fire dispatch LifeShield can help you navigate the process if you have any questions or concerns 4 1 Y 2021 Cabot Blvd West Langhorne PA 19047 Life Shield Customer Support 1 888 885 6070 www lifeshield com 2013 LifeShield Inc All rights reserved LifeShield is a registered trademark of LifeShield Inc
28. ore than contact with water for b Flood water sensing E 3 minutes more than 3 minutes i Locate the water probe assembly with wires attached as shown and mount it near the baseline surface ex floor using the supplied double faced tape or suitable wall mounting screws not supplied It is recommended that the probe be mounted between O to 1 8 above the baseline surface ab ii Loop the free end of the Water Probe wire through the back of the wireless transmitter as shown in Figure A and connect the wire pair to the loop terminal block by inserting the wires individually into the loop terminals and tightening the screws iii Determine the best location to install the mounting plate above the location where the Water Probe has been installed being careful not to position it too high beyond the length of the wires now connecting the water probe and wireless transmitter ater probe iv Using either the supplied screws or double faced adhesive tape secure the mounting bracket to a flat surface wall or ceiling g Install the CR123 battery supplied into the wireless transmitter noting the correct orientation of the ENG O positive and negative ends A Position the wireless transmitter over the mounting plate and slide the wireless transmitter securely into place until it clicks Floor ADD THE SENSOR TO THE LIFESHIELD SYSTEM MEME E Once the Temperature and Flood Water Sensor is in
29. ox check with the Knowledge Base or refer to the LifeShield User Manual both found on lifeshield com 2 What is the LifeShield Return Policy This policy applies to purchases made directly from lifeshield com through a LifeShield Security Advisor or through an authorized partner You can return the System for any reason and cancel this Contract within 7 days after the System is installed or activated Please call 1 888 885 6070 to receive a Return Material Authorization RMA number If you do not install or activate the System within thirty 30 calendar days of your order you will conclusively be deemed to have accepted your System and this Contract will continue in force Once you activate your system you will enter a 7 day practice period After the 7 day practice period the not monitored notification on your console will disappear and your system will be fully monitored We are not obligated to issue an RMA after thirty 30 calendar days after your order You must return the products to our warehouse within twenty 20 calendar days of the issuance of the RMA Accessory products purchased with a kit or separately from a kit are also subject to return policies listed here Returns must be in the original box with all parts and manuals in original resalable condition along with a copy of your purchase receipt Be sure to include the RMA number on the return package We will exchange it or offer you a refund based on your original method of pay
30. sername and Password 2 Click Disarm 5 Enter Master Code Panicking Your System An alarm generated by pressing the PANIC button will send a message to the Alarm Monitoring Center to contact the authorities without making a call to you to verify the alarm Do not attempt to test your system by using the Panic Button Emergency Services will be dispatched You can panic your system using one of the 2 devices Console and Keychain Remote TO PANIC Using the Console 1 Press and hold PANIC for 2 seconds if enabled 2 Select Police Fire or Medical if no selection is made police will be default selection Using the Keychain Remote 1 Press and hold STAY and AWAY at the same time for 2 seconds if enabled and you re near your home NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK 20 21 RESPONDING TO AN ALARM 1 PANIC When you panic your system local authorities will be dispatched to your monitored address automatically There will be no phone call to verify the status of your alarm and the signal cannot be canceled 2 BURGLARY amp FIRE In the event of an alarm the monitoring center will call to verify the status of the alarm a The Primary Contact will be called first If they do not answer the Secondary Contact will be called b If neither of the contacts can be reached then the monitoring center will automatically dispatch emergency services c If one of t
31. sitive spelling and spacing must be exact amp Once Wifi information has been saved wait 2 minutes before unplugging the power and then Ethernet g After 2 minutes plug power back into camera and leave Ethernet unplugged Once power light is solid the camera is wireless and ready for final placement If the camera works while connected to the Ethernet but not wirelessly then the WiFi information must be verified Repeat step D if necessary NOTES Must be on same router as your LifeShield Base to setup After setup plug into power where you like Setup WiFi using camera Settings in LifeView disconnect Ethernet cable then remove and reconnect the power Setup alerts in LifeView to take pictures when sensors tigger Live video per session is 5 minutes If the camera works while connected to the Ethernet but not wirelessly then the WiFi information must be verified Repeat step D if necessary Wireless or WiFi technology allows an electronic device to exchange data wirelessly using radio waves over a computer network To reset insert paperclip into reset button next to power connector for at least 5 seconds and release a Wifi antenna must be installed to use WiFi Use rubber cover for Ethernet plug Use rubber cover for power plug The RC8221 is an indoor camera with built in Infrared LEDs for night vision TO USE First plug Ethernet cord into camera and router Wait for Pow
32. splayed on the LCD screen Wait 5 seconds then detach the Smoke Sensor from the mounting bracket Un clip Sensor from bracket You will have 30 seconds to complete this step When the Smoke Sensor has successfully been added you will hear 4 fast confirmation beeps from the LifeShield system If there are no confirmation beeps check to make sure that the battery insulator tab has been removed re attach the Smoke Sensor to the mounting bracket and repeat the steps above Once the Smoke Sensor has been added to the LifeShield system Use the Edit feature to rename the device if desired Press DELETE to erase text and the keypad keys to type new ones l Press OK then press BACK until the Main Menu is displayed Re attach the Smoke Sensor to the mounting bracket TEST THE SMOKE SENSOR On the Handset or Console press MENU Scroll to Utilities press SELECT Scroll to Test press SELECT Enter your Master Code Select System Test Press the SKIP soft key to skip the Siren Test Press the OK soft key on next screen for Starting Comm Test Scroll to the name of the Sensor that you would like to test and press SELECT 500090 900909 On the Smoke Sensor press the small Test button located on the front cover for at least 5O seconds If the Smoke Sensor test is successful the LCD screen will display Sensor xxx Passed If these words do not appear return to Add the Smoke Sensor to the LifeShield System 15 NOTE WHER
33. stalled it must be added to the LifeShield system in order to function You will need a Handset or Console to add it Enter the Security menu on the Handset or Console On the Handset or Console Press MENU Scroll to Security Setup press SELECT and enter the Master Code m Scroll to Sensors press SELECT Scroll to Add New gt press SELECT em Scroll to Environmental press SELECT Continued on next page NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK 16 ADD THE SENSOR TO THE LIFESHIELD SYSTEM CONTINUED P Following the instructions displayed on the Handset or Console wait 5 seconds then press and release the red tamper switch button on the wireless transmitter see Figure A Once the Sensor has been added to the LifeShield system Use the Edit feature to rename the device optional NOTE Press DELETE to erase text and use the keypad keys to type in a new name Once you are satisfied with the entered name press OK Scroll down to select the type of condition to which this Sensor will be associated Flood Cold Warm or Hot and press SELECT Press OK to return to the Main Menu 50 Position the top cover in place over the wireless transmitter and snap it into place being careful not to pinch or cut the wires leading to the Water Probe if the Sensor is set up for Flood detection If the Sensor test is successful the LCD scr
34. take a few seconds IF NO GCS HEARD SENSORS IS DISPLAYED THE SENSOR IS TOO FAR FROM THE CLOSEST CONSOLE BASE OR CELLULAR GATEWAY Press OK Edit Sensor Name Optional You can change the name now or at a later time Change Preprogrammed Sensors Menu To change the Sensor Name press the DELETE key to remove the default name Using the keys on your Console keypad type in the desired name Press OK when complete Sensor Placement Scroll to Door or Window Press OK Alarm Type Scroll to Stay amp Away Away Only or Convenience Press OK Testing your Sensor T With system disarmed test your Sensor by opening the door or window Correct setup will generate a chime sound If you don t hear a chime sound see troubleshooting in the User Manual Adding additional Sensors fe NOTE WHEREVER MASTER CODE IS SHOWN PLEASE USE YOUR UNIQUE MASTER CODE FOUND IN THE FRONT COVER OF THIS BOOK Repeat steps A N for additional Sensors Squeeze amp Hold Metal Clip f iLifeShield A O Ready To Arm Thu 2 8 11 48a ooo0oo0o000 CANCEL OFF O OOOOOOO oo0oo0oo0o000 Ooooooo OOoooooo Oooooooo INSTANT STAY o o YO C sol Buttons za 6 If you have more than one Remote you must create new User Codes before those keychains can be added The LifeShield system can support up to 8 Users 1 Master User who is able to change System Se
35. tching movies or TV or going to bed arm the system using the INSTANT key You want to use this when you re not expecting anyone to enter the house and when you re not planning on going out With INSTANT arming No Exit or Entry Delay is provided and opening a door that s armed will generate an immediate alarm You can arm your system using one of the 3 devices Console LifeView Web Application and LifeView Mobile Annlications TO ARM Using the Console 1 Press INSTANT on your Console and enter your Master Code Using the LifeView Web Application 1 Login to LifeView with your User Name and Password 2 Click Arm Instant Using the LifeView Mobile Applications 1 Login to LifeView with your Username and Password 2 Click Instant 5 Enter Master Code Disarming Your System Use this whenever you want to CANCEL any alarm you ve caused You can disarm your system using one of the 4 devices Console Keychain Remote LifeView Web Application and LifeView Mobile Applications TO DISARM Using the Console 1 Press CANCEL OFF on your Console and enter your Master Code Using the Keychain Remote 1 Press Cancel OFF to disarm the system before entering 2 The system will respond with a light blink and beep letting you know the system is disarmed Using the LifeView Web Application 1 Login to LifeView with your User Name and Password 2 Click Disarm Using the LifeView Mobile Application 1 Login to LifeView Application with your U
36. ttings and 7 Normal Users who are only able to Arm and Disarm the system FOR MULTIPLE KEYCHAINS YOU MUST CREATE A UNIQUE USER FOR EACH KEYCHAIN User Codes can easily be added changed or deleted from the system Console Here are the steps to add a pregrogrammed Keychain Remote Press Menu on Console Scroll to Security Setup on the screen press Select Enter Master Code Scroll to Users Select Add New It defaults to User 1 use the delete button to erase default username Enter desired name using keypad numbers press OK M Create a unique 4 digit arming code for this user press OK AA System will ask you to confirm New User add press OK NOTE IF YOU HAVE ADDITIONAL USERS TO CREATE SELECT ADD NEW AND REPEAT If you are ready to add additional keychain remotes please continue with steps below Press the Button under Back which displays on the Screen Scroll down to Keychains M Select Add New M Press all 3 Keychain buttons M Select user to assign the Keychain to Menu Menu c Add Additional Keychain Remote s NOTE Your Keychain Remote is ready to go and preprogrammed for a Master User A LifeShield Ready To Arm Thu 2 8 11 4 a Oooooooo CANCEL OFF o Oooooooo OoOoooooo OoOoooooo OOoOooooo OoOoooooo INSTANT STAY o o Oooooooo Keychain Remote e x ALi
Download Pdf Manuals
Related Search