Table of Contents
Contents
1. or button 4 Once you don t operate the OSD menu after a pre set time the OSD menu will automatically disappear English 14 On Screen Display Menus First OSD Menu Horizontal Position Horizontal Position Changes the horizontal position of the image Vertical Position Changes the vertical position of the image Frequency Changes the display data frequency to match the frequency of your graphic card When you are experiencing vertical flickering bar use this function to make an adjustment Tracking Synchronizes the signal timing of the display to that of the graphic card When you are experiencing unstable to flickering image use this function to make an adjustment Reset Returns the display parameters of the current mode to its factory default settings OSD Off Time Adjusts the time period for the OSD menu to disappear English 15 Second OSD Menu Vv Vv Vv gt v Color Setting Color Setting Obtains an optimum color of the display Color Adjustment Red Adjusts the red color of the display Color Adjustment Green Adjusts the green color of the display Color Adjustment Blue Adjusts the blue color of the display Display Mode Shows the display resolution vertical refresh and horizontal scan of the current mode Language Chooses the language you need There are English French German Spanish and Italian for your choi2. LI Cable Management 1_8B8 ae Device English 6 Connectors Display Rear Connectors DC Power In Display Input Display Stand Back USB Hub Ports LE Ei ta _ 4 USB Downstream Ports USB Upstream Port English 7 Start Your Installation Connecting the Display To setup this display please refer to the following figure and procedures 1 Be sure all equipment is off 2 Connect the VGA signal cable from display input connector to the 15 pin connector of your host computer and tighten the screws 3 Connect the DC power cord to the power connector plug one end of the AC power cord into the power adapter and then the other end into an electrical outlet TTT a A A BES qa ese N A VGA Cable AC DC Power Adapter AC Power Cord Notice To ensure the LCD display can work well with your computer please configure the display mode of your graphic card to make it less than or equal to 1024 x 768 resolution and make sure timing of the display mode is compatible with the LCD display We have listed the Compatibility Modes of this LCD display in appendices for your reference Englis
3. English Table of Contents Usage Notice PICCAULIONS asec cre ies the ah oe ek oa 2 Introduction About the Product ii 3 Package QOUCIVIOW scioglie lai 4 Installation Product OVErvieW ii 5 Start Your Installation a r A O S 7 User Controls Front Bezel CONtrolS vrrriirie rire 11 How to Use the OSD MENUS iiiiiiiiii 13 On Screen Display Menus iiiiii 14 Appendices TFOUDIOSNOONIG 51h 16 Product DIMENSIONS iii 17 Compatibility Modes iii 18 1 English 2 Usage Notice A Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture A Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recom mended in this user s manual to maximize product usage life Do D Turn off the product before cleaning Use only a dry soft cloth or clean room wiper when cleaning the LCD panel surface Q Use a soft cloth moistened with mild detergent to clean the display housing Use only the AC DC power adapter provided by manufacturer Disconnect the power plug from AC outlet if the product will not be used for a long period of time na Oo Don t a Donottouch the LCD panel surface with sharp or hard objects O Donotuse abrasive cleaners waxes or solvents for
4. an adjustment English 17 Product Dimensions 342mm 13 5 322 5mm 12 7 oo 00 00 da FEOEUwUTESA 7v fer E a Front View H 128 9mm 5 1 Side View C 40 9mm 1 6 Top View English 18 Compatibility Modes H Frequency V Frequency Mode Resolution kHz Hz IBM amp VESA VGA 31 47 70 09 IBM amp VESA VGA 31 47 70 09 IBM amp VESA VGA 31 47 59 94 VESA SVGA x 600 37 88 60 32 VESA XGA 1024 x 768 48 36 60 00
5. ces English 16 Appendices Troubleshooting If you are experiencing trouble with the LCD display refer to the follows If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected as described in the Installation section Make sure the pins of the connectors are not crooked or broken Problem Partial image or incorrectly displayed the image gt Check to see if the resolution of your computer is higher than that of the LCD display Reconfigure the resolution of your computer to make it less than or equal to 1024 x 768 gt Adjust the vertical refresh of computer to 60Hz Problem Image has vertical flickering line bars Use Frequency to make an adjustment Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display Problem Image is unstable and flickering Use Tracking to make an adjustment Problem Image is scrolling Check and make sure the VGA signal cable is well connected gt Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display Problem Vague image characters and graphics Use Frequency to make an adjustment If this problem still exists use Tracking to make
6. h 8 Display and system setting For the optimum display of your monitor please follow the procedures as below 1 Adjust the vertical refresh of your graphic card to 60Hz a Ifthe monitor setting of your computer provides vertical refresh selection set the vertical refresh to 60Hz b Ifthe monitor setting of your computer does not provide the vertical refresh selection b 1 Check your graphic card driver if the driver supports vertical refresh selection install the driver and set to 60Hz b 2 If the driver does not provide the vertical refresh selection please contact your graphic card s dealer for a vertical refresh selection supported driver 2 Activate the Auto Adjustment function to obtain optimum image by pressing S A button 3 If necessary pop up the OSD menu and use the Horizontal Position Vertical Position Frequency Tracking adjustments to fine tune the display image English 9 USB Hub USB Downstream Ports These four USB ports are available for connecting USB type peripheral devices such as keyboard mouse printer and so on USB Upstream Port This port is for connecting the USB Upstream cable to computer s or other hub s USB port English 10 Cable Management 1 Route the cables through the cable management device 2 Connect the cables
7. to their respective connectors on the back panel of the display Cable Management Device English User Controls Front Bezel Controls No go OF OG 11 0 0 6 To Control Brightness Minus Minus Brightness Plus Plus Menu button Select Auto Function 1 Decreases the brightness of the display image 2 Decreases value of the adjustment items 1 Increases the brightness of the display image 2 Increases value of the adjustment items To pop up the OSD menus Select To select the adjust ment items from OSD menus Auto To activate the Auto Adjustment function to obtain an optimum image English 12 Contrast Minus Minus 6 Contrast Plus Plus 7 Power Switch Power LED 1 Decreases the contrast of the display image 2 Decreases value of the adjustment items 1 Increases the contrast of the display image 2 Increases value of the adjustment items Switches on off the power of the LCD display 1 Green indicates the display is turned on 2 Amber indicates the display in power saving mode English 13 How to Use the OSD Menus 1 Press the D Menu button to pop up the on screen menu and to toggle between Main Menu Page 1 and Page 2 2 Choose the adjustment items by pressing the S A Select Auto button 3 Adjust the value of the adjustment items by pressing the
8. your cleaning Q Donot operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong electronic magnetic emission radiation field Direct sunlight place English 3 Introduction About the Product Having a 14 1 inch flat panel screen with an active thin film transistor TFT liquid crystal display LCD this product also demon strates following outstanding features Q Direct analog RGB input Q 14 1 diagonal screen size Q 16 7 million displayable colors Q 1024 x 768 resolution Q XGA SVGA VGA VESA compatible Q 31 50kHz horizontal scan a 60 70Hz refresh rate Q Auto adjustment capability Q Fullscreen re scaling a Multilingual OSD menus in five languages English French German Spanish and Italian Q USB hub with 1 upstream and 4 downstream ports on the stand base Q VESA DDC 1 2B data communication a VESA DPMS power saving Q Stand with tilt and cable management functions O VESA standard 75mm x 75mm mounting interface English 4 Package Overview Power Cord VGA Signal Cable USB Upstream Cable a7 User s Manual Warranty Card Installation Diskette for DDC1 2B English 5 Installation Product Overview Main Unit LCD Display Stand Rear View
Download Pdf Manuals
Related Search