Product Name
Contents
1. the VoIP cable modem Plug the other power cord into the PB1000 and then into the AC wall outlet The lights on the PB1000 should turn on as described on the previous page Wait a few moments and then verify your connection to the Internet and your telephone by checking for dial tone and making a test call This completes the installation of the PB1000 Installing the Motorola PB1000 in a New VoIP Environment If this is the initial installation of the VoIP cable modem follow the steps below 1 2 Install the VoIP cable modem according to the instructions in the SBV4200 or SBV5120 User Guide up to the point where AC power is connected Follow steps 4 10 found in Installing the Motorola PB1000 in an Existing VoIP Environment User Guide PB1000 9 Limited Warranty PB1000 Battery Backup for Motorola VoIP Cable Modems Motorola Inc Connected Home Solutions Business Motorola Retail Purchasers f you purchased this Product directly from Motorola or from an authorized Motorola retail reseller Motorola warrants to you the original end user customer that A the Product excluding Software will be free from defects in materials and workmanship under normal use and B with respect to Software i the media on which the Software is provided will be free from defects in material and workmanship under normal use and ii the Software will perform substantially as described in its documentation This Limited Warrant2. 00 include Reliable long life lithium ion battery technology Provides up to eight hours standby or up to six hours talk time No tools are required when battery replacement is required Lights on the PB1000 indicate battery status Your Internet service provider ISP can remotely monitor the battery status Additional Motorola PB1000 replacement batteries are available The battery is maintained at full charge by special circuitry in the PB1000 Note When the PB1000 is installed for the first time or if a battery pack is replaced or if the battery is fully discharged the battery may take up to 12 hours to reach full charge 6 PB1000 User Guide PB1000 Lights Item Label 1 Replace Battery 2 Battery 3 Power Color Condition Red Off Steady On Amber Steady On Flashes once per second Flashes 3 times per second Off Off Green Steady On Flashes once per second Description Normal condition indicating that the battery is in good condition Replace the battery Normal condition indicating that AC power is present and the battery is in good condition AC power is present and a battery low condition exists or AC power is not present and battery low condition exists AC power is present and a bad battery condition exists AC power is not present and battery is in good condition AC power is not present and a bad battery condition exists Normal condition indicating that AC power is p
3. Product that you can use and enjoy Motorola does not warrant that the functions of the Product will meet your requirements or that the operation of the Product will be uninterrupted or error free MOTOROLA IS NOT RESPONSIBLE FOR PROBLEMS OR DAMAGE CAUSED BY THE INTERACTION OF THE PRODUCT WITH ANY OTHER SOFTWARE OR HARDWARE ALL WARRANTIES ARE VOID IF THE PRODUCT IS OPENED ALTERED AND OR DAMAGED 10 PB1000 User Guide THESE ARE YOUR SOLE AND EXCLUSIVE REMEDIES for any and all claims that you may have arising out of or in connection with this Product whether made or suffered by you or another person and whether based in contract or tort IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT INDIRECT GENERAL SPECIAL INCIDENTAL CONSEQUENTIAL EXEMPLARY OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF INFORMATION OR ANY OTHER PECUNIARY LOSS OR FROM ANY BREACH OF WARRANTY EVEN IF MOTOROLA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO CASE SHALL MOTOROLA S LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT These matters are governed by the laws of the Commonwealth of Pennsylvania without regard to conflict of laws principles and excluding the provisions of the United Nations Convention on Contracts for the International Sale of Goods Retail Purchasers Only If you purchased th
4. User Guide PB1000 Battery Backup Q MOTOROLA for Motorola VolP intelligence everywhere Cable Modems 2 PB1000 User Guide Safety Information WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING DO NOT PLACE OBJECTS FILLED WITH LIQUIDS SUCH AS VASES ON THE UNIT CAUTION THIS PRODUCT WAS QUALIFIED UNDER TEST CONDITIONS THAT INCLUDED THE USE OF THE SUPPLIED CABLES BETWEEN SYSTEMS COMPONENTS TO ENSURE REGULATORY AND SAFETY COMPLIANCE USE ONLY THE PROVIDED POWER CABLE AND INSTALL IT PROPERLY CAUTION DIFFERENT TYPES OF CORD SETS MAY BE USED FOR CONNECTIONS TO THE MAIN SUPPLY CIRCUIT USE ONLY A MAIN LINE CORD THAT COMPLIES WITH ALL APPLICABLE PRODUCT SAFETY REQUIREMENTS OF THE COUNTRY OF USE CAUTION INSTALLATION OF THIS PRODUCT MUST BE IN ACCORDANCE WITH NATIONAL WIRING CODES AND CONFORM TO LOCAL REGULATIONS CAUTION DO NOT OPEN THE UNIT DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION CHANGES AND MODIFICATIONS NOT EXPRESSLY APPROVED BY MOTOROLA FOR COMPLIANCE COULD VOID USER S AUTHORITY TO OPERATE THE EQUIPMENT When using this device basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following Read all of the instruct
5. ates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Canada Industry Canada IC This Class B digital device complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada FCC Declaration of Conformity According to 47CFR Parts 2 and 15 for Class B Personal Computers and Peripherals and or CPU Boards and Power Supplies used with Class B Personal Computers Motorola Inc Connected Home Solutions Business 101 Tournament Drive Horsham PA 19044 1 215 323 1000 declares under sole responsibility that the product identifies with 47CFR Part 2 and 15 of the FCC Rules as a Class B digital device Each product marketed is identical to the representative unit teste
6. cle or other outlet unless the plug can be fully inserted with no part of the blades exposed Place this equipment on a stable surface Postpone installation until there is no risk of thunderstorm or lightning activity in the area Avoid using this product during an electrical storm There may be a risk of electric shock from lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the cable system This will prevent damage to the product due to lightning and power surges It is recommended that the customer install an AC surge protector in the AC outlet to which this device is connected This is to avoid damaging the equipment by local lightning strikes and other electrical surges Do not cover the device or block the airflow to the device with any other objects Keep the device away from excessive heat and humidity and keep the device free from vibration and dust User Guide PB1000 3 Wipe the unit with a clean dry cloth Never use cleaning fluid or similar chemicals Do not spray cleaners directly on the unit or use forced air to remove dust Operate this product only from the type of power source indicated on the product s marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company To prevent injuries or burns do not allow metal objec
7. d and found to be compliant with the standards Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted due to quantity production and testing ona statistical basis as required by 47CFR 2 909 Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The above named party is responsible for ensuring that the equipment complies with the standards of 47CFR Paragraph 15 101 to 15 109 User Guide PB1000 International Declaration of Conformity We Motorola Inc Connected Home Solutions Business 101 Tournament Drive Horsham PA U S A declare under our sole responsibility that the PB1000 to which the declaration relates is in conformity with one or more of the following standards EN55022 EN55024 EN60950 CISPR 22 CISPR 24 IEC 60950 3 Edition the following provisions of the Directive s of the Council of the European Union EMC Directive 89 336 EEC Low Voltage Directive 73 23 EEC Directive 93 68 EEC Introduction The Motorola PB1000 Battery Backup provides standby power for your SBV4200 or SBV5120 Voice over IP VoIP cable modem if you temporarily lose power at your location It ensures that you do not lose telephone service during a power outage for up to eight hours Features of the PB10
8. ided through this equipment Are not intended to replace or be a substitute for primary line voice services or Plain Old Telephone Service POTS Are not meant to provide guaranteed 911 or E911 services or to permit access to 411 directory assistance services Your service provider not Motorola is responsible for the provision of VoIP telephony services through this equipment Motorola shall not be liable for and expressly disclaims any direct or indirect liabilities damages losses claims demands actions causes of action risks or harms arising from or related to the services provided through this equipment IMPORTANT You CANNOT make any calls using this VoIP device if your broadband connection is not functioning properly or if you lose electrical power for a period exceeding the battery storage SAVE THESE INSTRUCTIONS Regulatory Information FCC Compliance Class B Digital Device This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment gener
9. ions listed here and or in the user manual before you operate this equipment Give particular attention to all safety precautions Retain the instructions for future reference This device must be installed and used in strict accordance with manufacturer s instructions as described in the user documentation that comes with the product Comply with all warning and caution statements in the instructions Observe all warning and caution symbols that are affixed to this equipment Do not use this product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool Do not overload outlets or extension cords as this can result in a risk of fire or electric shock Overloaded AC outlets extension cords frayed power cords damaged or cracked wire insulation and broken plugs are dangerous They may result in a shock or fire hazard Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords where they are attached to plugs and convenience receptacles and examine the point where they exit from the product Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord Place unit to allow for easy access when disconnecting the power cord of the device from the AC wall outlet Do not connect the plug into an extension cord recepta
10. is Product directly from Motorola or from a Motorola authorized retail reseller please call the Motorola toll free number 1 866 957 1300 for technical support or warranty service Cable Operator or Service Provider Arrangements f you did not purchase this Product directly from Motorola or from a Motorola authorized retail reseller please contact your Service Provider for technical support Specifications General Dimensions 3 3 cm 1 2 H x 9 5 cm 3 74 W x 15 0 cm 5 9 D Output Power 15 Watts Input Power 100 to 240 VAC 50 60 Hz 0 37 A Battery Type Lithium ion Battery Life Expectancy 3 to 5 years Environmental Operating Temperature 0 C to 40 C 32 F to 104 F Storage Temperature 10 C to 60 C 14 F to 140 F Operating Humidity 5 to 95 R H non condensing Visit our website at www motorola com User Guide PB1000 11 Copyright 2005 by Motorola Inc All rights reserved No part of this publication may be reproduced in any form or by any means or used to make any derivative work such as translation transformation or adaptation without written permission from Motorola Inc Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change Motorola provides this guide without warranty of any kind either implied or expressed including but not limited to the i
11. mplied warranties of merchantability and fitness for a particular purpose Motorola may make improvements or changes in the product s described in this manual at any time MOTOROLA and the Stylized M Logo are registered in the US Patent amp Trademark Office All other product or service names are the property of their respective owners Visit our website at www motorola com MOTOROLA 523271 001 4 05 MGBI
12. mproper use or application improper installation improper testing or unauthorized repair or ii to cosmetic problems or defects which result from normal wear and tear under ordinary use and do not affect the performance or use of the Product Motorola s warranties apply only to a Product that is manufactured by Motorola and identified by Motorola owned trademark trade name or product identification logos affixed to the Product Motorola does not warrant to you the end user or to anyone else that the Software will perform error free or without bugs MOTOROLA IS NOT RESPONSIBLE FOR AND PROVIDES AS IS ANY SOFTWARE SUPPLIED BY 3rd PARTIES EXCEPT AS EXPRESSLY STATED IN THIS SECTION WARRANTY INFORMATION THERE ARE NO WARRANTIES OF ANY KIND RELATING TO THE PRODUCT EXPRESS IMPLIED OR STATUTORY INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR THE WARRANTY AGAINST INFRINGEMENT PROVIDED IN THE UNIFORM COMMERCIAL CODE Some states do not allow for the exclusion of implied warranties so the above exclusion may not apply to you What additional provisions should I be aware of Because it is impossible for Motorola to know the purposes for which you acquired this Product or the uses to which you will put this Product you assume full responsibility for the selection of the Product for its installation and use While every reasonable effort has been made to insure that you will receive a
13. resent AC power is not present and battery is in good or low condition Note A battery low condition exists when the Motorola PB1000 battery pack capacity is less than 20 User Guide PB1000 7 Installing the Motorola PB1000 in an Existing VolP Environment Follow this procedure if the VolP cable modem is already installed and VolP phone service is operational at your location 1 Unplug AC power from the SBV4200 or SBV5120 VoIP cable modem by unplugging the AC cord from the AC wall outlet Do not reapply AC power until instructed to do so later in this procedure It is not necessary to unplug anything else for an existing installation such as the PC or telephone connections 2 Unplug the installed external power supply from the back of the VoIP cable modem and store it in a safe place Typical Connections Either or PB1000 User Guide Remove the battery cover from the PB1000 Backup Battery supply by pushing on the center locking tab and sliding it up Slide the battery into the battery compartment until it is fully seated It is keyed so that it cannot be installed incorrectly Make sure that the pull tab on the battery is accessible and does not prevent the battery cover from closing properly Re install the battery cover with the locking tabs seated downward and then push the cover forward Battery Installation o on Q Plug the keyed power plug on the PB1000 into the back of
14. such as dropping or striking with a hard object At the end of battery life the PB1000 battery must be disposed of properly and may need to be recycled Contact your local recycling center for proper disposal methods Do not expose the battery to ultrasonic energy Do not disassemble modify or attempt to repair the battery Before installation batteries should not be subjected to temperatures below 10 C or above 60 C 14 F to 140 F After initial customer usage initially charged above shipping charge state batteries should not be subjected to temperatures outside the operating temperature range Battery Pack External Exposure Operating Temperature Range Charging 0 0 C to 45 0 C 0 F to 113 F Discharging 10 0 C to 60 0 C 14 F to 140 F CARING FOR THE ENVIRONMENT BY RECYCLING When you see this symbol on a Motorola product do not dispose of the product with residential or commercial CW waste Recycling your Motorola Equipment Please do not dispose of this product with your residential or commercial waste Some countries or regions i such as the European Union have set up systems to collect and recycle electrical and electronic waste items Contact your local authorities for information about practices established for your region If collection systems are not available call Motorola Customer Service for assistance 4 PB 1000 User Guide Important VoIP Service Information Any services prov
15. ts to contact or short circuit the battery terminals Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating condition Safety Requirements for the Motorola PB1000 Lithium lon Battery You must properly handle the PB1000 lithium ion rechargeable battery to ensure your safety Improper handling can cause leakage heat smoke explosion or fire resulting in damage to the equipment or the user Use the PB1000 battery only in the PB1000 Battery Backup charger CAUTION Risk of explosion if battery is replaced by the incorrect type Use only Motorola approved batteries Motorola P N 515757 001 Do not use the battery where static electricity is generated Do not heat the battery or discard into a fire Keep the battery away from high temperature locations Properly discard the battery if it exhibits an abnormal condition such as heat odor color or a change in shape When discarding place insulated tape over the battery terminals The battery should be stored out of the reach of children Do not store the battery close to metal objects If the battery leaks fluid and you touch it immediately wash your hands If the fluid gets into your eye do not rub the eye Rinse with water and immediately seek medical care Left untreated the battery fluid could cause damage to the eye Ensure that the battery does not receive any strong impacts
16. y to you the original end user customer continues A for Software and the media upon which it is provided for a period of ninety 90 days from the date of purchase from Motorola or an authorized Motorola reseller and B for the Product excluding Software for a period of two 2 years from the date of purchase from Motorola or from an authorized Motorola reseller To take advantage of this Limited Warranty or to obtain technical support you must call the Motorola toll free phone number below Motorola s sole and exclusive obligation under this Limited Warranty for retail sales shall be to repair or replace any Product or Software that does not meet this Limited Warranty All warranty claims must be made within the applicable Warranty Period Cable Operator or Service Provider Arrangements lf you did not purchase this Product directly from Motorola or from a Motorola authorized retail reseller Motorola does not warrant this Product to you the end user A limited warranty for this Product including Software may have been provided to your cable operator or Internet Service Provider Service Provider from whom you obtained the Product Please contact your Service Provider if you experience problems with this Product General Information The warranties described in this Section shall not apply i to any Product subjected to accident misuse neglect alteration Acts of God improper handling improper transport improper storage i
Download Pdf Manuals
Related Search