VR1100 A & E
Contents
1. DIVISION 28 23 23 VR1100 SERIES FIBER OPTIC RECEIVER ENGINEERING SPECIFICATIONS PART 1 GENERAL 1 01 SUMMARY A Fiber Optic AM Video Receiver 1 02 SECTION INCLUDES A VR1100 Series AM Video Receiver Standalone B VR1100 R3 Series AM Video Receiver Rack Mount 1 03 REFERENCES A Underwriters Laboratory UL B Underwriters Laboratory Canada ULC 1 04 SYSTEM DESCRIPTION A Performance Requirements Provide an AM Video Receiver with AGC automatic gain control 1 The system shall utilize an 850nm optic capable of receiving a video signal on one multimode optical fiber VR1100 1 05 SUBMITTALS A Product Data Manufacturer s printed product data sheet for each type of Transmitter Receiver specified B Detail Drawings Electrical and optical connect drawings Product mounting template C Manufacturer s Installation and Operating Manual Printed installation and operating information for each type of Transmitter Receiver specified D Test Reports Manufacturer s Printed Test Report via a Tektronics VM700A Video Test Generator verifying product performance meets or exceeds the specified product performance referenced in Part 2 E Warranty Manufacturer s Printed Warranty 1 06 DELIVERY STORAGE AND HANDLING A Deliver materials in unopened factory packaging with Manufacturer s bar coding to the job site B Inspect product upon delivery to assure that specified products have2. been received C Store in original packaging in a climate controlled environment Storage Temperature not to exceed 40 C to 85 C 1 07 PROJECT SITE CONDITIONS A Temperature Requirements Products shall operate in an environment with an ambient temperature range of 40 C to 74 C without the assistance of fan forced cooling B Humidity Requirements Products shall operate in an environment with relative humidity of 0 to 95 non condensing If product is installed in condensation conditions unit shall have conformal coating applied to the printed circuit board 1 08 WARRANTY Project name project number date Optional information e g owner A E 00000 1 A Standard International Fiber Systems Comprehensive Lifetime Warranty IFS warrants the product to be free of factory defects under manufacture s Lifetime Warranty as submitted under article 1 05 E PART 2 PRODUCTS 2 01 MANUFACTURER A Acceptable Manufacturer International Fiber Systems Inc 16 Commerce Road Newtown CT 06470 USA Telephone 203 426 1180 Fax 203 426 3326 Email sales ifs com Internet www ifs com B Substitutions Not Permitted C All fiber optic modules shall be supplied from a single manufacturer 2 02 MANUFACTURED UNITS A Model Number Descriptions Reference Table A Product Number Descriptions B Model Compatibility Chart Reference Table B Product Compatibility Chart 2 03 GENERAL SPECIFICATIONS A The AM Vi
3. 001 R3 VT1000AC END OF SECTION Section Title 00000 4 Project name project number date Optional information e g owner A E
4. d of anodized aluminum E Weight lt 2 0 Ibs 1 0kg 2 10 ENVIRONMENTAL SPECIFICATIONS MTBF gt 100 000 Hours Operating Temp 40 C to 74 C Storage Temp 40 C to 85 C Relative Humidity 0 to 95 non condensing If product is installed under condensation conditions unit shall have conformal coating applied to the printed circuit board Add C to model number for conformal coated printed circuit board 2 11 REGULATORY AGENCIES APPROVALS AND LISTINGS A Underwriters Laboratory UL Listing Number I T E 6D16 B Underwriters Laboratory Canada ULC Listing Number I T E 6D16 C UL 94 flame rated PCB board 94VO D 2 12 ACCESSORIES Ue Ge Ne comp Section Title 00000 2 A Card Cage IFS Model Number R3 EIA 19 card cage shall be available to house and power rack mount modules B Blank Panels IFS Model Number R3 BP shall be available to cover unused rack slots PART 3 EXECUTION 3 01 EXAMINATION A Inspect modules before installation B Modules shall be free of any cosmetic defects or damage C All optical connectors shall be covered with dust caps and remain on the module until installing cable connectors to module D Shipping box shall include the module power supply and operations manual 3 02 PREPARATION A Standalone Module Surface Mount 1 Shall be mounted on a properly prepared surface adequate for the size and weight of module The placement of the unit
5. deo Receiver shall be an IFS VR1100 series module The module shall be capable of receiving full color video in real time in NTSC PAL or SECAM formats The module shall require no in line attenuators to ease installation The module shall provide power and AGC status indicating LED s for monitoring proper system operation The module shall provide AGC automatic gain control so there will be no optical or electrical in field adjustments to ease installations The modules shall provide automatic re settable solid state current limiters and independent voltage regulators on each module to reduce the chance of a single point failure of the system The module shall be hot swappable in a rack mount system to reduce complete system shut down during maintenance or repair The module shall have an MTBF of gt 100 000 hours and operate in an environment of 40 C to 74 C and relative humidity between 0 to 95 non condensing The module shall be UL and ULC listed and The circuit board shall be UL 94 flame rated and meet all PCI standards All PC boards shall be designated with part number PC board number and show appropriate revision number Housing shall be of all metal construction All LED indicators and both electrical and mechanical connections shall be identified with silk screened labels The module shall have a lifetime warranty to reduce system life cycle cost in an event of a module failure 2 04 VIDEO SPECIFICATIONS Output V
6. ideo 1 volt pk pk 75 ohms Bandwidth 5 Hz 10 MHz Differential Gain lt 5 Differential Phase lt 5 Tilt lt 1 Signal Noise Ratio 60dB eo eS Section Title 2 05 OPTICAL SPECIFICATIONS A IFS Model Number VR1100 Optical Fiber 62 5 125 micron multimode Number of Fibers Required 1 Optical Wavelength 850nm Optical Receiver Type 850nm Pin Diode Optical Attenuation No manual adjustments required 2 06 STATUS INDICATORS A Power On Red Off Off B AGC automatic gain control AGC Yellow No AGC Off 2 07 CONNECTORS A Optical ST B Power Terminal Block with Screw Clamps C Video BNC Gold Plated Center PIN 2 08 ELECTRICAL SPECIFICATIONS A Power 12VDC B Current Protection Automatic re settable solid state current limiters C Voltage Regulation Solid state Independent on each board D Circuit Board UL 94 flame rated and meets all PCI standards E Rack mount Card Shall be hot swappable with IFS Model Number R3 EIA 19 card cage 2 09 MECHANICAL SPECIFICATIONS A Surface Mount Dimensions 7 1 x 4 9 x 1 0 18 00 cm x 12 45 cm x 2 54 cm B Rack Mount Dimensions 7 7 x 5 0 x 1 0 19 56 cm x 12 70 cm x 2 54 cm C Number of Rack Slots 1 D Finish Module shall be constructed of a metal enclosure with a powder coat finish model Number F63B 12 with all connections and indicators silk screened directly on unit Rack mount units shall be constructe
7. ifications and covered Project name project number date Optional information e g owner A E with dust caps until connection to the fiber optic module 3 03 INSTALLATION A General Locate fiber optic modules as indicated on the approved detail drawings and install module in compliance with the IFS installation and operations manual 3 04 TESTING A Testing the Fiber Optic Video Link 1 Verify that the coax and optic fibers are properly connected Project name project number date Optional information e g owner A E 00000 3 2 Make sure that power is applied to all fiber optic modules camera and video monitor or other equipment used in the system 3 The level detect indicator LED should be lit confirming a presence of a video signal 4 Successful video link operation should be visible at this point as witnessed by a good quality video picture on the monitor 3 05 CLEANING A Follow all instructions for proper use of solvents and adhesives used for termination and splicing B At completion of the installation dispose of all fiber scraps properly Section Title MANUFACTURED UNITS REFERENCE TABLES Table A Product Number Descriptions VR1100 SERIES DESCRIPTION VR1100 MM 850 gt Video 1 Fiber VR1100 R3 MM 850 gt Video 1 Fiber Rack Mount Table B Product Compatibility Chart RECEIVER COMPATIBLE TRANSMITTERS VR1100 VT1101M VT1001 VT1001 R3 VT1000AC VR1100 R3 VT1101M VT1001 VT1
8. shall allow provision for cable installation and maintenance as indicated on the approved detail drawings and in compliance with the IFS mounting template and installation manual B Rack Mount Module 19 Rack 1 Shall be installed in the IFS Model Number R3 card cage Ensure the card cage is installed in a standard EIA 19 482 6 mm rack or wall standoff bracket adequate for the size and weight of the card cage The placement of the unit shall allow provision for cable installation and maintenance as indicated on the approved detail drawings and in compliance with the IFS installation manual C ae Fibers Caution NEVER look into the end of an active optical fiber when using laser light output Eye damage can occur Wear eye protection when cleaving terminating and splicing fiber 2 The number and type multimode or single mode of optical fiber shall meet the requirements of the IFS model number in article 2 05 used in the installation 3 All optical fiber cables shall be properly installed and terminated with the mating optical connectors as submitted in article 2 07 A 4 The optical link shall be tested with either a power meter at a minimum or OTDR to ensure the link budget overall path loss plus an added 3dB of optical safety margin does not exceed the optical power budget as submitted in article 2 05 5 All optical connectors on cable shall be cleaned in compliance to optical connector manufactures spec
Download Pdf Manuals
Related Search