PDF Prospectus
Contents
1. C 169 F for extended periods of time more than 2 hours may cause damage to worklight and possible fire or explosion DANGER Never store FLEXLITE battery models in sunshine SPECIFIC SAFETY RULES Know your worklight Read operator s manual carefully Learn its applications and limitations as well as the specific potential hazards related to this worklight Following this rule will reduce the risk of electric shock fire or serious injury Lens and housing become hot during use During or immediately after use don t lay worklight flat on lens surface or place lens area in contact with a plastic or fabric covered surface Handle worklight with care around any flammable surface Do not use or permit use of worklight in bed or sleeping bags This worklight lens can melt fabric and a burn injury could result Use only the adaptor recommended for use with your worklight Do not substitute any other adaptor Use of another adaptor could cause batteries to explode causing possible serious injury Do not charge battery pack in a damp or wet location Following this rule will reduce the risk of electrical shock Your battery worklight should be charged in a location where the temperature is more than 10 C 50 F but less than 37 C 99 F Do not disassemble your worklight Do not permit children to use worklight unsupervised It is not a toy The temperature of the light head will become hot2. after being on for only a short period of time This hot temperature can cause burn injury if touched and can create sufficient heat to melt some fabrics Stay alert Watch what you are doing and use common sense Do not rush If wrapped or in contact with fabrics the worklight lens can produce sufficient heat to melt some fabrics To avoid serious personal injury never allow the worklight lens to come in contact with anything Check damaged parts Before further use of this worklight a part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Do not use worklight if it does not function properly A WARNING STAND Do not install the light stand outside in windy weather The stand can fall and injuries could result A WARNING LED LIGHT Do not stare into the beam or view directly with or without optical instruments A WARNING Do not project the light toward a road another person or any vehicle to prevent blindness Doing so may result in serious injuries or death SAFETY RULES FOR CHARGER WARNING READ AND UNDERST AND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury Before using battery adaptor read all instructions and cautionary markings in this manual on the battery charger and on the product using the battery to prevent misu
3. ANTEE POLICY To receive a replacement you must present proof of purchase and return all original equipment packaged with the original product The replacement will be covered by the limited warranty for the balance of the 1 YEAR service warranty period WHAT IS COVERED UNDER THE 1 YEAR LIMITED SERVICE WARRANTY This warranty on FLEXLITE covers all defects in workmanship or materials including the brushes switches LED and cables for one year after the purchase date Malfunction is covered by warranty only if the product has been used normally and not if it results from misuse Warranties for other FLEXLITE products may vary HOW TO OBTAIN SERVICE To obtain service for this FLEXLITE you must return it freight prepaid or take it in to an authorized service center for FLEXLITE You may obtain the location of the authorized service center nearest you by calling toll free 1 866 854 1411 or by logging on to the FLEXLITE website at www flexlite ca When requesting warranty service ask for a RMA number before returning any products and you must present the original dated sales receipt The authorized service center will repair any faulty workmanship and at our discretion either repair or replace any part covered under the warranty at no charge to you WHAT IS NOT COVERED This warranty applies only to the original purchaser and may not be transferred This warranty only covers defects arising under normal usage and does not cover any mal
4. OPERATOR S MANUAL CORDLESS WORKLIGHT FLX6SB Your worklight has been engineered and manufactured to our high standard for dependability ease of operation and operator safety When properly cared for it will give you years of rugged trouble free performance WARNING To reduce the risk of injury the user must read and understand the operator s manual before using this product Thank you for buying FLEXLITE products SAVE THIS MANUAL FOR FUTURE REFERENCE M Ca Ny ra 5 Printed and made in Canada he wa Patent pending GENERAL SAFETY RULES A WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit Cluttered benches and dark areas invite accidents Working temperature This worklight is designed to be used at normal room temperature If used under 0 C 32 F the battery will discharge faster If used over 45 C 113 F an automatic cut off will turn the light off until the temperature of the light head comes down Depending on if the work area is closed with or without a fresh air draft the cut off temperature can be affected see Features for more information FLEXLITE is designed to be used in an industrial environment in rain snow and dust but FLEXLITE products can not be immersed
5. Optional see our website for more options Harness for transportation on your back FLX HTB Transformer to recharge FLX6SB on 110 or 240V AC FLX Ad 12V4A ASSEMBLY UNPACKING This product has been shipped completely assembled Carefully remove the worklight and any accessories from the box Make sure that all items listed in the packing list are included Inspect the worklight carefully to make sure no breakage or damage occurred during shipping Do not discard the packing material until you have carefully inspected and satisfactorily operated the worklight Ifany parts are damaged or missing please call 1 866 854 1411 for assistance PACKING LIST Worklight Operator s Manual Wallmount charger WARNING Do not attempt to modify this worklight or create accessories not recommended for use with this worklight Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury WARNING Never disconnect the connector on the light head unit when power is turned on A WARNING If any parts are missing do not operate this worklight until the missing parts are replaced Failure to do so could result in possible serious personal injury WARNING Keep FLEXLITE out of reach of children The worklight may cause serious injuries To avoid possible strangulation keep harness away from children This worklight is
6. Symbol Indicates a situation that may result in property SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair When servicing use only identical replacement parts WARNING To avoid serious personal injury do not attempt to use this product until you have thoroughly read and completely understood the operator s manual Save this operator s manual and review frequently for continuing safe peration and instructing others who may use this product SAVE THESE INSTRUCTIONS FEATURES PRODUCT SPECIFICATIONS FLX6SB Battery Must be replaced by a qualified service center SA BP12C14 4V Charger adpator Input cN iiini es ea ioa FLXSB AC 100 to 240V 50 to 60Hz AC Or FLXSB LP 12V DC lighter plug 8 5 Ibs for 1 headlight at 100 1755 lumens at 50 878 lumens at 25 439 lumens EFA Ca y rne n A E n an 93 Color temperature 5000 K Depth errare oa n a eanreavisersuadiene 10 cm Penat eee iii Espia EAEE R E RN 123 cm Width 8 5 cm Standard housing material Maximum height extended Anodized aluminum painted steel plastic 294 cm Battery performance at 21 C 70 F for 1 head for 2 heads 11 hours 6 hours 20 hours 11 hours 38 hours 20 hours 18 hours 9 hours Working temperature ss ss 20 to 50 C 4 to 122 F
7. center IMPORTANT INFORMATION FOR RECHARGING A HOT WORKLIGHT When using the worklight continuously the batteries in the battery pack will become hot You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge NOTE Refer to CHARGING THE BATTERY for normal recharging of batteries If the charger does not charge your battery pack under normal circumstances return both the battery pack and charger to your nearest repair center for electrical check For the location of your nearest repair center please call 1 866 854 1411 OPERATION Use Touch Pad switch in front of the lighthead TO TURN WORKLIGHT ON Push and hold 2 seconds DIM FROM 100 TO 50 Push quickly once DIM FROM 50 TO 25 Push quickly another time FLASHING MODE Push quickly another time TURN OFF Push and hold 2 seconds at anytime SAFETY ADVICE Ifthe light head becomes too hot an integrated electronic device will turn down the light power to 25 of efficiency on blinking mode If the temparature still increases the device will cut off the light automatically Verify if the heatsink is clean Ifthe problem persists return the worklight to an authorized service center When the battery becomes discharged the light head will automatically turn down the light power to 25 of efficiency to allow the user several minutes to leave the dark area MAINTENANCE WARNING When servicing us
8. e only identical FLEXLITE replacement parts Use of any other parts may create a hazard or cause product damage WARNING A Always wear safety goggles or safety glasses with side shields when using compressed air to clean worklights If operation is dusty also wear a dust mask GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc FAN AND OR HEATSINK MAINTENANCE This FLEXLITE is made with an integrated cooling fan designed to resist rain and dust This fan and air flow heatsink must be cleaned frequently to perform well Use only a low air pressure gun to clean and remove any dust Don t use solvent soap or cleaner The unit is clean when you can see across the heatsink WARNING A Do not immerse in water WARNING Do not at any time let brake fluids gasoline petroleum based products penetrating oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury BATTERIES This worklight is equipped with lithium ion Polymer rechargeable batteries Length of time before servicing will depend on the type of work you are doing The batteries in the housing have been designed to provide maximum trouble free life However like all batteri
9. es they will eventually wear out Do not disassemble housing and attempt to replace the batteries Handling of these batteries especially when wearing rings and jewelry could result in a serious burn Battery Life Batteries that lose 20 of their capacity must be removed from service and disposed of properly Return FLEXLITE to your servicing center to replace the battery 10 KNOW YOUR FLEXLITE Boutons d ajustement Wall fixation holes 2 Trous de fixation au mur 2 Tension adjustment Ajustement de la tension Wall stand Support mural Electronic controls amp battery packs Contr les lectroniques et batteries Battery charger socket Socle du chargeur de batterie Adjustment knobs Boutons d ajustement LED lights Lumi res LED Protection glass Vitre de protection 12V DC socket or cord 12V DC prise ou cordon Fan air flow amp heatsink Sortie d air du ventilateur amp heatsink On off switch mode selector Interrupteur s lecteur de mode Power cable Cordon d alimentation WARRANTY FLEXLITE 1 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting warranty service Limited to FLEXLITE purchased 1 December 2010 and after This product is manufactured by FP Technologies The FLEXLITE trademark is licensed by FP Technologies All warranty communications should be directed to FP Technologies Technical Service at toll free 1 866 854 1411 GUAR
10. function failure or defect resulting from misuse abuse neglect alteration modification or repair by other than an authorized service center for FLEXLITE brands FLEXLITE MAKE NO WARRANTIES REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS WORKLIGHT OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY ADDITIONAL LIMITATIONS To the extent permitted by applicable law all implied warranties including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE are disclaimed Any implied warranties including warranties of merchantability or fitness for a particular purpose that cannot be disclaimed under state law are limited to one year from the date of purchase FLEXLITE are not responsible for direct indirect incidental or consequential damages Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 12
11. in water If the working area is moist and dusty some particles will stick on the fan or heatsink and reduce the performance See maintenance section to remove any dirt A DANGER Never connect disconnect or use an external power supply or charger in a hazardous area A DANGER Never connect or disconnect the connector on the lighthead or any extension cord when the power is on or in a hazardous area ELECTRICAL SAFETY A battery operated worklight with integral batteries charger FLX6SB must be connected properly to a 12Volts DC source to be recharged Using another wallmount charger clip may create a risk of fire Use wallmount adaptor only with the product listed 110 240Vac CHARGER LIGHTER PLUG FLXSB AC FLXSB LP SERVICE Worklight service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel may result in a risk of injury When servicing a worklight use only identical replacement parts Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury STORAGE TEMPERATURE Store worklight at room temperature between 4 and 27 C 40 and 80 F for best results When transporting or temporarily storing in a vehicle temperature range should be between 35 C 31 F and 66 C 151 F Storing worklight at temperatures greater than 76
12. not a toy OPERATION WARNING Do not allow familiarity with worklights to make you careless Remember that a careless fraction of a second is sufficient to inflict serious injury WARNING Do not use any attachments or accessories not recommended by the manufacturer of this worklight The use of attachments or accessories not recommended can result in serious personal injury CHARGING THE BATTERY The battery for this worklight is shipped in a low charge condition to prevent possible problems Therefore you should charge the battery for a minimum of 6 hours TO CHARGE Charge the battery pack only with the recommended adaptor See FEATURES section on page 6 Connect the adaptor properly to power supply Turn off the light clip and lock the FLX6SB on the wallmount adaptor After normal usage minimum 4 hours of charging time is required to be fully charged Do not place the FLX6SB in an area of extreme heat or cold It will work best at normal room temperature When the battery becomes fully charged unplug the charger from the power supply The charger will cut off automatically if battery is fully charged WARNING A Keep the wallmount charger and the worklight out of reach of children WARNING A Do not try to open wallmount charger or worklight No parts can be changed by user To replace battery return worklight and wallmount charger to authorized service
13. plastic An extension cord should not be used unless absolutely necessary Use of an improper extension cord could result in a risk of fire and electric shock If an extension cord must be used make sure That pins on plug of extension cord are the same number size and shape as those of plug on charger That the extension cord is properly wired and in good electrical condition and That wire size is large enough for AC ampere rating of adaptor as specified below Cord Length Feet 25 50 100 Cord Size AWG 16 16 16 NOTE AWG American Wire Gauge Do not operate adaptor with a damaged cord or plug which could cause shorting and electric shock If damaged have the charger replaced by an authorized serviceman Do not operate adaptor if it has received a sharp blow been dropped or otherwise damaged in any way Take it to an authorized serviceman for an electrical check to determine if the charger is in good working order Do not disassemble adaptor Take it to an authorized serviceman when service or repair is required Incorrect reassembly may result in a risk of electric shock or fire Unplug adaptor from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock Disconnect adaptor from the power supply when not in use This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening It also will help prevent damage to the charger during a power su
14. rge Risk of electric shock Do not touch uninsulated portion of output connector Save these instructions Refer to them frequently and use them to instruct others who may use this worklight If you loan someone this worklight loan them these instructions also to prevent misuse of the product and possible injury SYMBOLS Some of the following symbols may be used on this worklight Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the worklight better and more safely SYMBOL NAME DESIGNATION EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency cycles per second W Watt Power min Minutes Time al Alternating Current Type of current Direct Current Type or a characteristic of current D Class II Construction Double insulated construction A Safety Alert Precautions that involve your safety The following signal words and meanings are intended to explain the levels of risk associated with this product SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation which if not avoided will result A in death or serious injury WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION ie Safety Alert
15. se of the products and possible injury or damage CAUTION To reduce the risk of electric shock or damage to the charger and battery charge only batteries as specifically designated on your adaptor Other types of batteries may burst causing personal injury or damage Do not use charger outdoors or expose to wet or damp conditions Water entering adaptor will increase the risk of electric shock Use of an attachment not recommended or one sold by another manufacturer may result in a risk of fire electric shock or injury to people Following this rule will reduce the risk of electric shock fire or serious personal injury Do not abuse the cord of the adaptor Never use the cord to carry the adaptor Do not pull the charger cord rather than the plug when disconnecting from receptacle Damage to the cord or charger could occur and create an electric shock hazard Replace damaged cords immediately Make sure cord is located so that it will not be stepped on tripped over come in contact with sharp edges or moving parts or otherwise subjected to damage or stress This will reduce the risk of accidental falls which could cause injury and damage to the cord which could result in electric shock Keep cord and adaptor away from heat to prevent damage to housing or internal parts Do not let gasoline oils petroleum based products etc come in contact with plastic parts They contain chemicals that can damage weaken or destroy
Download Pdf Manuals
Related Search