Zipato User Manual v1.4
Contents
1. Having trouble installing your new product Zipato s website contains the latest user documentation and software updates for Zipato products and services www zipato com You can also find answers in the Zipato Community at community zipato com Zipato Support supportfazipato com LIMITED PRODUCT WARRANTY GENERAL TERMS Nothing in this Limited Product Warranty affects your statutory rights as a consumer The Limited Product Warranty set forth below is given by Tri plus grupa d o o Europe herein referred to as ZIPATO This Limited Product Warranty is only effective upon presentation of the proof of purchase Upon further request by ZIPATO this warranty card has to be presented too EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY www zipato com 04 ZIPATO MAKES NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ZIPATO EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD TO THE EXTENT ALLOWED BY LOCAL LAW THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO THEY DO NOT HOWEVER AFFECT OR RESTRICT THE RIGHTS YOU HAVE AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM IN NO EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR INDIRE2. Command 0x02 Meter_Report 0x02 Parameter 1 0x21 Scale Bit2 0 Rate Type 0x01 Meter Type 0x01 Parameter 2 0x34 Precision 1 Scale Bit1BitO 0x02 Size 4 Parameter 3 4 0x00 Instant Power Consumption 0x000003EA 100 2W Parameter 5 0x03 Parameter 6 OxEA Meter_Report 0x02 Parameter 1 0xA1 Scale Bit2 1 Rate Type 0x01 Meter Type 0x01 Parameter 2 0x4A Precision 2 Scale Bit1BitO 0x01 Size 2 Parameter 3 0x00 Current 0x002B 0 43A Parameter 4 0x2B Get power factor PF from endpoint Meter_GET example 2 3 2 BINARY_SWITCH_SET COMMAND_CLASS_MULTI_CHANNEL Get load voltage V from endpoint COMMAND_CLASS_MULTI_CHANNEL By using BINARY_SWITCH_SET Co mmand of Multi Channel MULTI_CHANNEL_CMD_ENCAP METER_GET example MULTI_CHANNEL_CMD_ENCAP Command Class Encapsulateion Command you can switch both Relay1 and Relay2 ON OFF by setting endpoint to 1 or switch Relay1 ON OFF by setting endpoint to 2 or switch Relay2 ON OFF by setting endpoint to 3 Below command example shows switching off relay1 of the Micromodule COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x01 C this is the endpoint of command owner here we assume endpoint is 1 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x01 O Bit Address 0 Destination End Point range1 3 Command Clas
3. INSTANT POWER CONSUMPTION VARY OVER 5 REPORT When the power consumption of load vary over 5 it will send Meter report to the nodes of Group www zipato com eae Class Meter Meter Report Rate Type 0x01 Meter Type 0x01 Precision 1 Scale 0x02 Size 4 Meter Value W 2 1 3 OVERLOAD ALARM REPORT COMMAND When Micromodule detects the overload it will send Alarm Report to the corresponding Group The content of Alarm Report Alarm report command Command_Class_Alarm Alarm_ Report Alarm Type 0x08 Alarm Level OxFF 2 2 RESPONSE TO METER GET COMMAND Micromodule will report its 1 instant Power Consumption Watt or 2 accumulated power consumption KWH or 3 AC load Voltage V or 4 AC load current 1 5 load power factor PF to Z Wave Controller after receive the Meter Get Command from Z Wave Controller 2 2 1 Instant Power Consumption Watt of Micromodule When receiving Meter Get Command it will report Meter Report Command to the node asked Meter Get Command Command Class Meter Meter Get Scale 0x02 W Command Class Meter Meter Report Rate Type 0x01 Meter Type 0x01 Precision 1 Scale 0x02 Size 4 Meter ValuelW Example Meter Value 1 0x00 W Meter Value 2 0x00 W Meter Value 3 0x03 W Meter Value 4 OxEA W Meter W Meter Value 3 256 Meter Value 4 100 2W 2 2 2 Accumulated Power Consumption KW h When receiving Meter Get Command it
4. everything under control MICROMODULE SWITCH DOUBLE QUICK ra si GUIDE v1 TRADEMARKS Zipato and the Zipato logo are registered Trademarks All other product names mentioned herein may be trademarks or registered trademarks of their respective companies NOTICE Although Zipato has attempted to ensure the accuracy of the content of this manual it is possible that this document may contain technical inaccuracies typographical or other errors Zipato assumes no liability for any error in this publication and for damages whether direct indirect incidental and consequential or otherwise that may result from such error including but not limited to loss of data or profits Zipato provides this publication as is without warranty of any kind either express or implied including but not limited to implied warranties of merchantability or fitness for a particular purpose The published information in the manual is subject to change without notice Zipato reserves the right to make changes in the product design layout and driver revisions without notification to its users This version of the Installation guide supersedes all previous versions ELECTROMAGNETIC COMPATIBILITY When operated according to manufacturer instructions the product complies with all applicable CE harmonised standards from EMC Directive 2004 108 EC and Part 15 of the FCC Rules The connections conducting HF signals must not be damaged o
5. 0xFF the load attached to the Switch turns on Command Class Switch Binary Switch Binary Set Value 0 0x00 the load attached to the Micromodule turns off 2 Z WAVE S GROUPS ASSOCIATION COMMAND CLASS VERSION 2 Micromodule can be set to send reports in order to control associated Z Wave devices It supports 3 association groups which every group has one node support Group1 Group3 support SWITCH_BINARY_REPORT METER_REPORT_COMMAND_ V3 For group 1 Micromodule will report 1 ON OFF status of Relay1 and Relay2 2 Instant Power Consumption Watt of Relay1 and Relay2 3 Accumulated Power Consumption KWh of Relay1 and Relay2 to Z Wave Controller For group 2 Micromodule will report 1 ON OFF status of Relay1 2 Instant Power Consumption Watt of Relay1 3 Accumulated Power Consumption KWh of Relay1 to Z Wave Controller For group 3 Micromodule will report 1 ON OFF status of Relay2 2 Instant Power Consumption Watt of Relay2 3 Accumulated Power Consumption KWh of Relay2 to Z Wave Controller 2 1 Auto report to Grouping 1 3 Maximum Node 1 2 1 1 On Off Event Report When on or off state has been changed by pressing S1 S2 or on off button it will send Binary Switch Report to the nodes of Group1 3 Binary Switch Report ON Command Class Switch Binary Switch Binary Report Value 255 0xFF OFF Command Class Switch Binary Switch Binary Report Value 0 0x00 2 1 2
6. Bese OF Binary_owitch_ Relay ON amp Relay2 ON Basic Set or Binary_Switch Basic net or Binary_Switch_ Relay1 OFF amp Relay2 OFF Get command Relay state Basic_Get or Binary_ Sieen Ce Relay1 ON amp Relay2 ON ON Basic_Get or Binary_ Relay1 OFF amp Relay2 OFF OFF Switch_Get Get command Parameter Report to command sender Relay1 KWh1 Relay2 Meter_Get KWh KWh 2 Meter_Get Watt Relay1 W1 Relay2 W2 Relay1 and Relay2 are Meter_Get Voltage the same voltage Meter_Get Current Relay1 11 Relay2 12 Power Meter_Get toe EE Relay1 3 4 EDGE AND PULSE MODE Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge Toggle mode default value is Edge mode 3 4 1 EDGE MODE This mode is suitable for the bi stable wall switch that has indicator point on the Micromodule and the same position correspond to same state of relay1 and relay2 if the Switch s relay changes the state because of receiving Z Wave RF command it may need two switchings switch on to off or switch off to on to let relay back to the corresponding state 3 4 2 PULSE MODE this mode is suitable for the toggle type wall switch to swap the state of Relay or Relay2 3 4 3 EDGE TOGGLE MODE This mode is suitable for the normal bi stable switch every state change of the wall switch will also swap the state of Relay1 or www Zzipato com Relay2 3 5 THRESHOLD OF WATT FOR LOAD CAUTION This is a warning when the wattage of load over the pr
7. Report OFF when relay 1 OFF 2 Report ON when relay 2 ON Configuration parameter 3 2 Report OFF when relay 2 OFF Report ON when either relay Configuration parameter 3 3 1 ON or relay 2 ON default Report OFF when both relay 1 and relay 2 OFF Basic Get Command Command Class Basic Basic Get Basic Report Command Report OFF Command Class Basic Basic Report Value 0 0x00 Report ON Command Class Basic Basic Report Value 255 0xFF make your home smart Binary Switch Get Command Command Class Switch Binary Switch Binary Get Binary Switch Report Command Report OFF Command Class Switch Binary Switch Binary Report Value 0 0x00 Report ON Command Class Switch Binary Switch Binary Report Value 255 0xFF 1 2 BASIC_SET SWITCH_BINARY_SET Since the switch have two relays the load attached to the Micromodule will turn on or off upon receipt of the following commands from a Z Wave Controller by setting Configuration parameter 3 Configuration parameter 3 1 Switch ON and OFF of relay 1 Configuration parameter 3 2 Switch ON and OFF of relay 2 Configuration parameter 3 3 Switch ON and OFF both relay default 1 and relay 2 Command Class Basic Basic Set Value 1 99 255 OxFF the load attached to the Micromodule turns on Command Class Basic Basic Set Value 0 0x00 the load attached to the Switch turns off Command Class Switch Binary Switch Binary Set Value 1 99 255
8. environment and protect human health At Zipato we understand and are committed to reducing any impact our operations and products may have on the environment To minimize this impact Zipato designs and builds its products to be as environmentally friendly as possible by using recyclable low toxic materials in both products and packaging COPYRIGHT 2015 Tri plus grupa d o o All Rights Reserved No part of this manual may be reproduced or transmitted in any form without the expressed written permission of Tri plus grupa d o o make your home smart www zipato com 05
9. the hardware components and all its internal components including firmware The term ZIPATO Hardware Product DOES NOT include any software applications or programs GEOGRAPHICAL SCOPE OF THE LIMITED PRODUCT WARRANTY This Limited Product Warranty is applicable to Hardware Products sold by Zipato Resellers in all countries listed at the beginning of this document under the heading Countries in which this ZIPATO Limited Product Warranty applies The Limited Product Warranty will be honored in any country where ZIPATO or its authorized service providers offer warranty service subject to the terms and conditions set forth in this Limited Product Warranty However warranty service availability and response times may vary from country to country and may also be subject to registration requirements LIMITATION OF PRODUCT WARRANTY ZIPATO warrants that the products described below under normal use are free from material defects in materials and workmanship during the Limited Product Warranty Period set forth below Limited Product Warranty Period if the product is used and serviced in accordance with the user manual and other documentation provided to the purchaser at the time of purchase or as amended from time to time ZIPATO does not warrant that the products will operate uninterrupted or error free or that all deficiencies errors defects or non conformities will be corrected This warranty shall not apply to probl
10. will report Meter Report Command to the node asked Meter Get Command Command Class Meter Meter Get Scale 0x00 KW h Command Class Meter Meter Report Rate Type 0x01 Meter Type 0x01 Precision 2 Scale 0x00 Size 4 Meter Value KWh Example Scale 0x00 KWh Precision 2 Size 4 Bytes KW h Meter Value 1 0x00 KWh Meter Value 2 0x01 KWh Meter Value 3 0x38 KWh Meter Value 4 0xA3 KWh Accumulated power consumption KW h Meter Value 2 65536 Meter Value 3 256 Meter Value 4 800 35 KW h 2 2 3 CLEARING ACCUMULATED POWER CONSUMPTION If you want to reset accumulated power consumption you can use Meter Reset Command to clear it Meter Reset Command Command Class Meter Meter Reset 2 2 4 AC LOAD VOLTAGE V When receiving Meter Get Command it will report Meter Report Command to the requested node Meter Get Command Command Class Meter Meter Get Scale 0x04 V Meter Report Command Command Class Meter Meter Report Rate Type 0x01 Meter Type 0x01 Precision 1 Scale 0x04 Size 2 Meter ValuelV Example Scale 0x04 V make your home smart Precision 1 Size 2 2 Bytes of V Meter Value 1 0x09 V Meter Value 2 0x01 V AC load Voltage Meter Value 1 256 Meter Value 2 230 5 V 2 2 5 AC LOAD CURRENT 1 When receiving Meter Get Command it will report Meter Report Command to the requested node Meter Get Command Com
11. 1 3 Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x01 Meter_Get 0x01 Parameter 1 0x30 Scale PF 0x06 Micromodule power factor report example COMMAND_CLASS_ MULTICHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Meter report Endpoint3 Bit Address Destination End Point 0x05 Bit Address 0 Destination End Point command owner Endpoint value Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x02 Meter_Report 0x02 Parameter 1 0xA1 Scale Bit2 1 Rate Type 0x01 Meter Type 0x01 Parameter 2 0x51 Precision 2 Scale Bit1BitO 0x10 Size 1 Parameter 3 0x63 Power Factor 0x63 0 99 3 Z WAVE S CONFIGURATION Configuration Parameter 1 Watt Meter Report Period 2 0x01 0x7FFF 5s 720 Be eens KWH Meter Report 2 Period 0x01 0x7FFF 10min 6 6 10min 1 hour Slected End Point 1 1 3 1 Relay1 1 2 Relay1 3 Relay1 amp Relay2 www zipato com 03 Configuration Parameter 4 Edge or Pulse mode or Edge 1 Es Toggle mode 1 Edge mode 2 Pulse mode 3 Edge Toggle mode Configuration Parameter 5 Threshold of Watt 2 for Load Caution Threshold of KWH 2 for Load Caution Restore switch state mode 1 0 2 0 Switch off 1 1 Last switch state 3 Switch on Configuration P
12. BUTTON three times within 2 seconds will enter exclusion mode One press one flash 0 5 second on Node ID has been excluded 1 Second oi Reset Pressing INCLUDE_BUTTON Use this three times within 2 seconds procedure will enter inclusion mode One press one only in the flack event that Within 1 second press On Off the primary _ button again for 5 seconds until controller LED is off is lost or ne p otherwise 5 second on inoperable IDS are excluged 0 5 second off Including a node ID allocated by Z Wave Controller means inclusion Excluding a node ID allocated by Z Wave Controller means exclusion Failed or success in including excluding the node ID can be viewed from the Z Wave Controller Sometimes people find it hard to execute exclusion or inclusion especially when Micromodule is already installed in a wall box To solve this issue Micromodule supports a special feature that can use S1 or S2 to execute exclusion inclusion Reset or Association during first 3 minutes when connected to the main power for first time PROGRAMMING 1 BASIC COMMAND CLASS BINARY SWITCH COMMAND CLASS Micromodule will respond to BASIC and BINARY commands that are part of the Z Wave system 1 1 BASIC_GET BINARY_SWITCH_GET Since the switch have two relay the Micromodule will report its On Off state to the Controller by setting Configuration parameter 3 Report ON when relay 1 ON Configuration parameter 3 1
13. CT SPECIAL INCIDENTAL CONSEQUENTIAL INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE HOWEVER NOTHING IN THIS AGREEMENT LIMITS ZIPATO S LIABILITY TO YOU I IN THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT RESULTING FROM ZIPATO S NEGLIGENCE OR II TO THE EXTENT RESULTING FROM ANY FRAUDULENT MISREPRESENTATION ON THE PART OF ZIPATO OR III TO THE EXTENT ARISING UNDER PART 1 OF THE CONSUMER PROTECTION ACT 1987 OF THE UNITED KINGDOM SOME STATES OR COUNTRIES DO NOT ALLOW 1 A DISCLAIMER OF IMPLIED WARRANTIES 2 A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR 3 LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS IN SUCH STATES OR COUNTRIES SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY TO YOU THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE OR FROM COUNTRY TO COUNTRY YOU ARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRY LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS This Limited Product Warranty applies to ZIPATO branded hardware products collectively referred to as ZIPATO Hardware Products sold by ZIPATO Europe its European subsidiaries affiliates authorized resellers or country distributors collectively referred to as ZIPATO Resellers with this Limited Product Warranty The term ZIPATO Hardware Product is limited to
14. MMAND_CLASS_SCENE_ACTIVATION COMMAND_CLASS_SCENE_ACTUATOR_CONF COMMAND_CLASS_PROTECTION COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_MULTI_CHANNEL_V3 COMMAND_CLASS_METER_V3 COMMAND_CLASS_CONFIGURATION OVER THE AIR FIRMWARE UPDATE Micromodule is based on 500 series SoC and supports Firmware Update Command Class so it can receive the updated firmware image sent by controller via the Z wave RF media It is a helpful and convenient way to improve some function if needed TROUBLESHOOTING 1 Micromodule is not working and LED off Cause of Failure The Switch is not connect to the Main power 1 Recommendation Check power connections Don t open up the Micromodule and send it for repair icromodule s LED illuminating but cannot control the ON OFF switch of the load attached Cause of Failure Check if the load connect into the Micromodule has its own ON OF switch E Recommendation Set the ON OFF switch of the load attached to ON E Micromodule s LED is illuminating but the Detector cannot control the Switch Cause of Failure Not carry out association Same frequency interference Recommendation Carry out association Wait for a while to re try LED keep flashing but cannot control Cause of Failure Overload occurs E Recommendation Remove the load attached or check max load cannot exceed 7 5A
15. Toggle It switches to the inverse of current state 3 9 4 Switch On It switches to ON state 3 10 EXISTENCE OF ENDPOINT3 Multi Channel Command is a good way to control relay1 and relay2 of Switch individually The endpoint3 of Micromodule is related to both relay1 and relay2 In some condition it becomes redundant in Multi Channel Command Class When the Existence of Endpoint3 is set as 2 the endpoint3 will be disabled The default value is 1 Endpoint1 and Endpoint2 are fixed only Endpoint3 is dynamic 4 PROTECTION COMMAND CLASSES Micromodule supports Protection Command Class version 2 it can protect the switch against unintentional control by e g a child And it can also protect the switch from being turned off by setting it in No RF Control state After being set to Protection by sequence state any intentional pressing of On Off button or S2 S2 should be held for longer than 1 second or the switch state will not change However the operation of learn function will not change because learning will not be protected Z WAVE COMMAND CLASSES COMMAND_CLASS_ZWAVEPLUS_INFO COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_SWITCH_BINARY COMMAND_CLASS_BASIC COMMAND_CLASS_SWITCH_ALL make your home smart COMMAND_CLASS_ALARM CO
16. arameter 8 Auto off timer 2 0 0x7FFF 0 Disable auto off 1s 0 function 1 Ox7FFF 1s 327675 RF off command mode 0 3 0 Switch off 0 1 Ignore 2 Switch toogle 3 Switch on Configuration Parameter 10 Existence of Endpoint3 1 Jeu 1 1 Endpoint exist 2 No Endpoint3 3 1 WATT METER REPORT PERIOD If the setting is configured for 1hour set value 720 Micromodule make your home smart will report its instant power consumption every 1 hour to the node of correspond Group The maximum interval to report its instant power consumption is 45 hours 5s 32767 3600 45hr 3 2 KWH METER REPORT PERIOD If the setting is configured for 1hour set value 6 Micromodule will report its Accumulated Power Consumption KW h every 1 hour to the node of correspond Group The maximum interval to report its Accumulated Power Consumption KW h is 227 55 days 10min 32767 1440 227 55 days 3 3 SELECTED RELAY If Micromodule is not using Multi_Channel command class to access the relay of Switch you may configure the select value to react the Basic Command Class Binary Switch Command Class or Meter Command Class V3 3 3 1 SELECTED RELAY1 Only relay1 can be controlled and report 3 3 2 SELECTED RELAY2 Only relay2 can be controlled and report 3 3 3 SELECTED RELAY1 AND RELAY2 DEFAULT SELECT IS 3 Both relay1 and relay2 can be controlled and report Set command Relay state Basic Set or Binary Switch
17. e the On Off button The LED will light ON for 1 second and the load plugged into the Micromodule will turn OFF make your home smart APPLICATION In Wall Switch 2 relay 1A Type Relay 1 Relay 1 CHOOSING A SUITABLE LOCATION Do not locate the Micromodule facing direct sunlight humid or dusty place The suitable ambient temperature is 0 C 40 C Do not locate the Micromodule where exists combustible substances or any source of heat e g fires radiators boiler etc After putting it into use Micromodule s casing can become little hot on touch which is normal operation LED INDICATION State Type LED Indication Whatever we switch On Off on the Micromodule Normal by S1 S2 or On Off button or RF command the LED will light up for 1 second Under normal operation when the Micromodule has not been allocated a node ID the LED No node ID flashes on and off alternately at 2 second intervals By pressing S1 S2 or On Off button it will stop flashing temporarily When Micromodule is in learning mode LED Learning flashes on and off alternately and repeatedly at 0 5 second intervals When overload state occurs the Micromodule is disabled of which LED flashes on and off Overload alternately at 0 2 second intervals Overload state can be cleared by disconnect and reconnect the Micromodule to the main power ADDING TO Z WAVE NETWORK In the front casing there is an on off button with LED indicator below wh
18. ems resulting from a unauthorized alterations or attachments b negligence abuse or misuse including failure to operate the product in accordance with specifications or interface requirements c improper handling d failure of goods or services not obtained from ZIPATO or not subject to a then effective ZIPATO warranty or maintenance agreement e improper use or storage or f fire water acts of God or other catastrophic events This warranty shall also not make your home smart apply to any particular product if any ZIPATO serial number has been removed or defaced in any way ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR THE ZIPATO HARDWARE PRODUCT LIMITED PRODUCT WARRANTY PERIOD The Limited Product Warranty Period starts on the date of purchase from ZIPATO Your dated sales or delivery receipt showing the date of purchase of the product is your proof of the purchase date You may be required to provide proof of purchase as a condition of receiving warranty service You are entitled to warranty service according to the terms and conditions of this document if a repair to your ZIPATO branded hardware is required within the Limited Product Warranty Period Other than in respect of products for domestic use in particular those listed in the first and last boxes in the table below this Limited Product Warranty extends only to the original end user purc
19. eset threshold value If the setting value is 750 when the load wattage of Relay1 or Relay2 over this value Micromodule will send Watt Meter Report command to the node of correspond Group the Range of the setting value Is from 10 to 750 and the default value is 750 3 6 THRESHOLD OF KWH FOR LOAD CAUTION This is a warning when the KWh of load exceeds preset threshold value If the setting value is 1000 when the Accumulated Power Consumption of Relay1 or Relay2 exceeds this value Micromodule will send KWh Meter Report command to the node of corresponding Group the Range of the setting value is from 10 to 1000 and the default value is 750 3 7 RESTORE SWITCH STATE MODE Whenever the AC power return from lost Micromodule will restore the switch state which could be SWITCH OFF LAST SWITCH STATE SWITCH ON The default setting is LAST SWITCH STATE 3 8 AUTO OFF TIMER Whenever Micromodule switches to on the auto off timer begin to count down After the timer decrease to zero it will switch off automatically However if Auto off timer is set as 0 the auto off function will be disabled The default setting is 0 3 9 RF OFF COMMAND MODE Whenever a switch off command BASIC_SET BINARY_SWITCH_ SET SWITCH_ALL_OFF is received it could be interpreted as 4 kinds of commands 3 9 1 Switch Off It switches to OFF state The default setting is Switch Off 3 9 2 Ignore The switch off command will be ignored 3 9 3 Switch
20. haser of this ZIPATO Hardware Product and is not transferable to anyone who obtains ownership of the ZIPATO Hardware Product from the original end user purchaser PRODUCT WARRANTY PERIOD TABLE PRODUCT TYPE Micromodule Switch Double PRODUCT WARRANTY TE PERIOD y IMPORTANT The content of Product Type listed above is subject to change please refer to the www zipato com for latest update PERFORMANCE OF THE LIMITED PRODUCT WARRANTY If a product defect occurs ZIPATO s sole obligation shall be to repair or replace any defective Zipato Hardware Product free of charge provided it is returned to an Authorized ZIPATO Service Centre during the Limited Warranty Period Such repair or replacement will be rendered by ZIPATO at an Authorized ZIPATO Service Centre All component parts or hardware products that are replaced under this Limited Product Warranty become the property of ZIPATO The replacement part or product takes on the remaining Limited Warranty Period of the replaced part or product The replacement product need not be new or of an identical make model or part ZIPATO may in its discretion replace the defective product or any part thereof with any reconditioned equivalent or superior product in all material respects to the defective product WARRANTOR Tri plus grupa d o o Banjavciceva 11 10 000 Zagreb CROATIA TEL 385 0 1 4004 404 FAX 385 0 1 4004 405 DECLARATION OF CONFORMITY d The manufacture
21. ial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet ona circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help DISPOSING AND RECYCLING YOUR PRODUCT When it reaches end of life dispose of the product according to your local enviromental laws guidelines and regulations H This symbol on the product or packaging means that according to local laws and regulations needs to be disposed of separately from household waste Once this product has reached the end of its life please take it to a collection point recycle facilites designated by your local authorities some will accept your product for free or simply drop it off at your Zipato re seller store By recycling the product and its packaging in this manner you help to conserve the
22. ich is used to toggle Micromodule on and off or carry out inclusion exclusion reset or association When first power is applied LED repeatedly flashes in 0 5 second intervals It implies that it has not been assigned a node ID and starts auto inclusion AUTO INCLUSION The function of auto inclusion will be executed as long as the in wall Micromodule does not have Node ID and is connected to main power Note Auto inclusion timeout is 2 minutes during which the node information of explorer frame will be emitted once every several seconds Unlike inclusion function as shown in the table below auto inclusion doesn t require pressing on off buttons on the Micromodule The table below lists an operation summary of basic Z Wave functions Please refer to the instructions for your Z Wave Primary www zipato com 01 Controller to access the Setup function and to include exclude associate devices Function Description LED Indication The Z Wave Controller does No node ID not allocate a node ID to the Micromodule 2 second on 2 second off Have Z Wave Controller entered inclusion mode by following the instructions provided by the controller manufacturer Pressing INCLUDE_BUTTON threetimes within 2 seconds will enter inclusion mode One press one Inclusion flack Have Z Wave Controller entered exclusion mode by following the instructions provided by the controller manufacturer Exclusion Pressing INCLUDE_
23. ies New Z Wave 500 series chip supports multichannel operation and higher data rates 9 6 40 100kbps Overload protection Auto reports wattage when variation exceeds 5 Very low power power consumption Over the air firmware update Easy installation SPECIFICATION TECHNICAL SPECIFICATION PROTOCOL Z Wave Plus OPERATING VOLTAGE 100 240VAC MAXIMUM LOAD 6 5A 230VAC 120VAC Resistive load OPERATING TEMPERATURE 0 C 40 C RANGE Minimum 30m indoor 70m outdoor WEIGHT 39g DIMENSIONS 46mm x 15mm x 39mm PACKAGE WEIGHT 68g PACKAGE DIMENSIONS 67mm x 22mm x 162mm REGULATIONS EMC 2004 108 EC R amp TTE 1995 5 EC LVD 2006 95 EC FCC PART 15 WARRANTY 1 year MODELS AND FREQUENCIES EUROPEAN UNION EU version UNITED STATES US version RUSSIA RU version ISRAEL IS version AUSTRALIA AU version INDIA IN version ph pan04 eu 868 42 MHz ph pan04 us 908 42MHz ph pan04 ru 869 02MHz ph pan04 is 916 02MHz ph pan04 au 921 42MHz ph pan04 in 865 20MHz INSTALLATION AND OPERATION Put the in wall Micromodule into a wall box and connect the AC power wire L N to Micromodule s connector L N Connect the Micromodule to the switch as shown in picture To manually turn ON the Micromodule press and release the On Off button The LED will light ON for 1 second and the load plugged into the Micromodule will also turn ON To manually turn OFF the Micromodule simply press and releas
24. ion End Point command owner Endpoint value Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x02 Meter_Report 0x02 Parameter 1 0xA1 Scale Bit2 1 Rate Type 0x01 Meter Type 0x01 Parameter 2 0x22 Precision 1 Scale Bit1BitO 0x00 Size 2 Parameter 3 0x09 Voltage 0x0910 232 0V Parameter 4 0x10 Get load current from endpoint Meter_GET example COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x05 this is the endpoint of command owner here we assume endpoint is 5 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x03 Bit Address 00Destination End Point range1 3 Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x01 Meter_Get 0x01 Parameter 1 0x28 Scale A 0x05 Micromodule AC load current I example COMMAND_CLASS_ MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Meter report Endpoint3 Bit Address Destination End Point 0x05 Bit Address 0 Destination End Point command owner Endpoint value Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x02 make your home smart Source End Point 0x05 this is the endpoint of command owner here we assume endpoint is 5 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x03 Bit Address 0 Destination End Point range
25. l be 0 Bit Address Destination End Point 0x03 Bit Address 0 Destination End Point range 1 3 Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x01 Meter_Get 0x01 Parameter 1 0x10 Scale W 0x02 Micromodule Power Consumption W Report example COMMAND_CLASS MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Meter report Endpoint3 Bit Address Destination End Point 0x05 Bit Address 0 Destination End Point command owner Endpoint value Command Class 0x32 Command_Class_Meter_V3 0x32 www Zzipato com COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x05 this is the endpoint of command owner here we assume endpoint is 5 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x03 Bit Address 0 Destination End Point range1 3 Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x01 Meter_Get 0x01 Parameter 1 0x20 Scale V 0x04 Micromodule AC load Voltage exmaple COMMAND_CLASS_ MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Meter report Endpoint3 Bit Address Destination End Point 0x05 Bit Address 0 Destinat
26. mand Class Meter Meter Get Scale 0x05 I Meter Report Command Command Class Meter Meter Report Rate Type 0x01 Perel pe 0x01 Precision 2 Scale 0x05 Size 2 Meter Valuell Example Precision 2 Size 2 2 Bytes of Meter Value 1 0x01 I Meter Value 2 0x21 I AC load current Meter Value 1 256 Meter Value 2 2 89 A 2 2 6 LOAD POWER FACTOR PF When receiving Meter Get Command it will report Meter Report Command to the requested node Meter Get Command Command Class Meter Meter Get Scale 0x06 PF Meter Report Command Command Class Meter Meter Report Rate Type 0x01 Meter Type 0x01 Precision 2 Scale 0x06 Size 1 Bytes Meter Value PF Example Scale 0x06 PF Precision 2 Size 1 1 Byte of PF Meter Value 1 0x63 PF It means that the load power factor is 0 99 2 3 MULTI CHANNEL COMMAND CLASS VERSION 3 Micromodule also supports muti channel command class version 3 which includes BINARY_SWITCH_GET BINARY_SWITCH_SET METER_SUPPORTED_GET METER_RESET METER_GET You may control or get report from 3 endpoints of Micromodule 2 3 1 BINARY_SWITCH_GET You may get the ON OFF state from every endpoint when endpoint set to 1 Micromodule will reply state of Relay1 If endpoint set to 2 Micromodule will reply state of Relay2 If endpoint set to 3 Micromodule will reply ON OxFF when either Relay 1 or Relay2 is ON report OFF 0x00 when both Rela
27. pport multi Channel this value will be 0 make your home smart Source End Point 0x05 this is the endpoint of command owner here we assume endpoint is 5 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x03 Bit Address 0 Destination End Point range1 3 Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x01 Meter_Get 0x01 Parameter 1 0x00 Scale KWH 0x00 Accumulated power consumption KWH Report example COMMAND_CLASS_ MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Meter report Endpoint3 Bit Address Destination End Point 0x05 Bit Address 0 Destination End Point command owner Endpoint value Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x02 Meter_Report 0x02 Parameter 1 0x21 Scale Bit2 0 Rate Type 0x01 Meter Type 0x01 Parameter 2 0x44 Precision 2 Scale Bit1BitO 0 Size 4 Parameter 3 4 0x00 Accumulated Power Consumption 0x000005FD 15 33 KWh Parameter 5 0x05 Parameter 6 OxFD Get Instant Power Consumption Watt from endpoint METER_GET example COMMAND_CLASS_ MULTICHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x05 this is the endpoint of command owner here we assume endpoint is 5 if the owner doesn t support multi Channel this value wil
28. r altered in any way by the user TAKE CARE OF YOUR SAFETY Display extreme caution when using ladders or steps please follow manufacturer s instructions Be careful when using hand and power tools and follow the manufacturer s guidelines when using them Take care that the correct tools are used Wear goggles or protective clothing where required DANGER RISK OF ELECTROCUTION All work on the device should only be carried out by trained and skilled electricians Observe the country specific regulations DANGER RISK OF FATAL INJURY FROM ELECTRIC CURRENT The device has no basic insulation and must therefore be installed in a way that protects against accidental contact DANGER RISK OF FATAL INJURY FROM ELECTRIC CURRENT When installing a wall plate the distance between the cover s fixing brackets or screws and the connections of the flush mounted MicroModule Switch Double must be at least 4 mm once installed If the distance is less than 4 mm a deeper installation box must be used The fixing brackets or screws of the cover must not press against the housing Only insulated tools may be used for operation on the device e g an insulated phase tester CAUTION The connected devices and the flush mounted receiver can become damaged if devices are operated that do not correspond to the technical specifications see technical data make your home smart INTRODUCTION Micromodule Switch Double is a transceiver
29. r Tri plus grupa d o o declares under our sole responsibility that the product Marketing model Micromodule Switch Double Regulatory model ph pan04 Trade Brand name Zipato is in conformity with the Low Voltage Directive 2006 95 EC EMC Directive 2004 108 ECand R amp TTE Directive 1995 5 EC and carries the CE marking accordingly www zipato com The following harmonized standards were applied R amp TTE 1995 5 EC EN 300 220 1 V2 4 1 EN 300 220 2 V2 4 1 EMC 2004 108 EC EN 301 489 1 V1 9 2 EN 301 489 3 V1 6 1 LVD 2006 95 EC EN 60669 2 1 2004 A1 2009 A12 2010 used in conjunction with EN 60669 1 1999 A1 2002 A2 2008 Changes or modifications not expressly approved by Tri plus grupa d o o for compliance could void the user s authority to operate the equipment re THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE Changes or modifications not expressly approved by Zipato for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a resident
30. s 0x25 O Command_Class_Switch_Binary 0x25 Command 0x01 O Switch_Binary_Set 0x01 Parameter 1 0x00 O ON 0xFF OFF 0x00 2 3 3 METER_SUPPORTED_GET This command is to ask the endpoint of Swtich what kind of meter data can be reported Below example shows how to get the meter report type COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x1 C this is the endpoint of command owner here we assume endpoint is 1 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x03 O Bit Address 0 Destination End Point range1 3 Command Class 0x32 CL Command_Class_Meter_V3 0x32 Command 0x03 O Meter_Supported_Get 0x03 Below is the example show Switch report to last command COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Bit Address Destination End Point 0x01 Command Class 0x32 CO Command_Class_Meter_V3 0x32 Command 0x04 O Meter_Supported_Report 0x04 Parameter 1 0x81 O Meter Reset 1 Meter Type 0x01 Parameter 2 0x75 O Scale Supported KWh W V A Power Factor 0x75 2 3 4 METER_RESET This command is to reset the Accumulated Power Consumption KWh to 0 The example show how to reset the KWh COMMAND_CLASS_ MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 C this is the endpoint of command owner here we assume endpoint is 3 if the owner doesn t su
31. which is a Z Wave Plus enabled device and is fully compatible with any Z Wave enabled network Mini size design allow the module to be easily hidden into the wall box which is good for the house decoration There are many kinds of application for using the module to switch AC power ON and OFF one of which is the light control The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kinds of light like incandescent fluorescent and LED light This Micromodule is able to detect Instant power wattage and overload wattage current 7 5A of connected light or appliances When detecting overload state the switch will be disabled and its ON OFF button will be locked during which LED will flash repeatedly Unplugging and reconnecting the Module will reset its overload condition to normal status OVERVIEW FIGURE 1 Dimensions unit mm wave ANTENNA Po as INCLUDE_BUTTON NEUTRAL LIVE NO1 X PACKAGE CONTENT 1PC Micromodule Switch Double 1PC Quick Installation Guide www zipato com FEATURES Slim compact remote Z Wave module switches and controls all parametres of power that your electrical appliances consume Voltage Current Power factor Instant power wattage and Accumulated power report Resistive load 1500W x 2 Zero crossing switch Higher output power enhances communication rangel 2 5dBm output power compared to 2 5dBm 300 ser
32. y 1 and Relay2 are OFF Below example shows a source endpoint 5 send a Get command to Micromodule endpoint 3 COMMAND_CLASS MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x05 this is the endpoint of command owner here we assume endpoint is 5 if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x03 Bit Address 0 Destination End Point range from 1 3 Command Class 0x25 Command_Class_Switch_Binary 0x25 Command 0x02 Switch_Binary_Get 0x02 Below is the example show Micromodule report to last command COMMAND_CLASS_MULTI_CHANNEL MULTI_CHANNEL_CMD_ENCAP Source End Point 0x03 Since the endpoint is 3 so Micromodule will reply ON OxFF www zipato com 02 either Relay 1 or Relay2 is ON report OFF 0x00 when both Relay 1 and Relay2 OFF Bit Address Destination End Point 0x05 O Bit Address 0 Destination End Point Command Class 0x25 O Command_Class_Switch_Binary 0x25 Command 0x03 O Switch_Binary_Reportet 0x3 Parameter 1 OxFF O ON 0xFF OFF 0x00 Bit Address Destination End Point 0x01 Bit Address 0 Destination End Point range1 3 Command Class 0x32 Command_Class_Meter_V3 0x32 Command 0x05 Meter_Reset 0x05 2 3 5 METER_GET Using meter get command to get the KWH W V I PF from endpoint of Switch Example
Download Pdf Manuals
Related Search