- WaiTrack© Fleet Management
Contents
1. GND MOTOR ACC V V Color Orange orange Grey Brown Green Blue Purple Yellow Orange Black Red Notes of the relay wiring The relay wiring of pump oil connectors of both ends are a fine white line 85 and a fine yellow line 86 The fine white line 85 is connected to vehicle positive power 12V The fine yellow line is connected to the device relay control line Instruction Connect to SOS button Connect to Microphone Sending data TX backup Receiving data RX backup Ground wire Connect to relay control line Connect to ACC ignition Vehicle 12V 24V negative storage battery Vehicle 12V 24V positive storage battery Cut off the positive connection line of the pump then connect in series to the relay N C contact thick green line 87a and the other end to relay COM contact thick green line 30 Note The standard relay is 12V and only suits the 12V car battery Please choose 24V relay if it is 24V car battery 4 4 Device wiring diagram E Connect to SOS button RX Interface Connect to microphone Yellow Orange AETA EEr Storage 12 24V battery ACC ION Relay 12V or 24V 85 30 87a 86 OFF as 5 START Ignition key 5 Cautions of device wiring 5 1 Power ACC Tele cutoff petrol electricity control line 4 pin 5 1 1 The standard voltage is 9V 36VDC Please use the power line which provided by the manufacturer The r2. ZB WailTrack GPS Vehicle tracker GPS GSM SMS GPRS User Manual Version 2 6T 1 Accessories NA power cord standard Relay standard SOS Alarm button Microphone standard standard Please check the accessories before using Pictures are for indication and illustration purposes only 2 Features e GSM 850 900 1800 1900 Quad band e Wide for voltage input range 9 36vDC e GPS continuous positioning GPRS timing interval e Check location via SMS e Built in vibration sensor theftproof e ACC ignition detection e Tele cutoff petrol electricity function e Three SOS numbers in maximum e SOS alarm and burglar alarm e Voice monitor function e Alarm when the power supply is disconnected intentionally with backup battery e Compatible with external connection through serial port eGeo fence via sms command 2 1 Red LED power working status LED Status Meaning Flashing interval 0 1s Low battery indication Continuously in bright state Charging Slow flashing interval 0 2s Full charge Continuously in dark state Low battery power off Slow flashing flash 0 1s after every 2s Working normally 2 2 Green LED GSM status indicator LED Status Meaning Quick flashing interval 0 1s GSM initialization Slow flashing flash 0 1s after every 2s Receive GSM signal normally Continuously in bright state GSM conversation Start GPRS Continuously in dark state No GSM signal 2 3 Blue LED GPS status indicato
3. If there is a power on password or pin please cancel it Ensure the SIM card can send and receive SMS 4 2 Installation The device installation is covert Please refer installation to an auto electrical contractor Under rear windshield NOTE 4 2 1 To prevent theft of the device it should be installed as covertly as possible Covertly installation is suggested 4 2 2 Avoid placing the device close to higher power electrical devices such as reversing radar anti theft device or other vehicle communication equipment 4 2 3 The device should be fixed into position with cable ties or wide double side tape 4 2 4 The device has built in GSM antenna and GPS antenna During installation please make sure the receiving side face is up with no metal object above the device to interfere with GPS reception The following places are suggested for installation shelter in the decorated board below the front windshield shelter around the front instrument panel non metallic material face in the decorated board below back windshield Notice if the windshield is pasted with metal thermal protective coating or heating coating It may affect the receiving signal In this case please change the installation place 4 3 Device outlet specification 2 0O0ONOOWALF O ang Z o Keypod Keypod MIC MIC TX GND VOTOR ACC V V TS Bean A U Ne zec Specification Keypod MIC MIC TX RX
4. sound in vehicle Incoming call from non special number will not activate voice monitoring function Note To realize this function please set special numbers beforehand The SIM card put into the device should be equipped with caller identification 7 8 Oil cut off 7 8 1 Via platform7 8 1 Send oil cut off command on platform To make sure the security of vehicle tracker can only indicate to cut off oil when GPS is in valid position status and the speed is less than 2OKM H or in static It needs password and platform account password is needed when sending oil cut off command 7 8 2 Via SMS Firstly you should set a center number Only center number can send the command to the device to cut off and restore oil The format is RELAY 1 After the command is carried out it will reply Cut off the fuel supply Success Speed 0 Km h If the command didn t carry out it will reply the reason about fail to carry out Note To ensure the safety of the driver and the car this command is valid only under two conditions the GPS is located the speed is less than 20km h 7 9 Restoring Oil 7 9 1 Via platform7 9 1 When the alarm is off sending recover oil commands manually Device will restore oil supplying and vehicle will work normally again Platform account password is needed when sending oil cut off command 7 9 2 Via SMS7 9 2 Only center number can send the command to the device to restore oil The format is RE
5. LAY O After the command is carried out it will receive Restore fuel supply Success 7 10 Over speed Alarm7 10 When the car is moving over a limited speed in average in a limited time period then the device will send over speed alarm SMS to user To turn on the over speed function please send below SMS command SPEED Time Limited speed Time range Minute 1 10 Limited speed range km h 0 255 0 refers to turn off over speed alarm function Example SPEED 3 120 Means when the car is moving over 120km h in average in 3 minutes the device will send over speed alarm to user Web8 Web based tracking online activation The GPRS web based tracking platform allows real time tracking with the latest Google maps There is also a playback feature that allows you to view where the vehicle has been for up to 30 days in the past making it ideal for fleet management Trouble9 Trouble shooting 9 1 After installing it in the first time if device can not get connected with platform server at this time it is logged off status in platform Please check the installation of device 1 Check whether the connection of power line is correct please do not connect it with the car control line 2 Check whether SIM card is installed correctly please refer to the installation manual 3 Check whether the power switch is toggled to ON the switch is in the left of the SIM card s slot 4 Whether ACC ignition cable i
6. default platform www gpsyeah com please send the SMS command below APN command format APN APN s Name E g APN internet internet is the APN of carrier The device will reply OK if setting successfully Note The APN of some countries have user name and password you may need to send SMS command as following APN APN name user name password E g APN internet CLIENTE AMENA 6 2 DNS setting To connect other platform please send the two SMS commands bleow Command format APN APN s APN APN s Name SERVER 1 DNS Port 0 SERVER 1 DNS Port O E g APN internet SERVER 1 www gpsluckly com 88 0 make sure you don t type LUKY but LUCKLY It will reply OK after set successfully 6 3 ON OFF GPRS When you want to disable GPRS you can sms command to the sim card number which used in the device Command format GPRS ON GPRSON 1 ON GPRSON 1 GPRS OFF GPRSON O OFF GPRSON O It will reply OK after set successfully 6 4 Add specific number SMS command to the device to set the SOS number SOS A No 1 No 2 No 3 A means to add new numbers for example SOS A 13510905991 13510905992 13510905993 If there is only one SOS number you can appoint a specific number as SOS number And the null means no adding For example SOS A 13510905991 means to set the first number as SOS number SOS A 13510905992 means to set the second number as SOS number SOS A 13510905993 means to set the
7. ed line is the positive The black line is the negative The negative should earth alone or link iron during installing Do not connect it to other ground wire 5 1 2 ACC line orange is connected to the ACC switch of the vehicle Please make sure to connect the ACC line The tracker will decide whether to enter ignition detection according to ACC status If do not connect to ACC line the device will enter ignition detection status If the vehicle vibrates when moving it will activate the vibration alarm If there is no need for the theftproof function connect the ACC line to the positive in parallel and keep high level 5 1 3 Tele cutoff petrol electricity control line yellow is connected to pin 86 of the Tele cutoff petrol electricity relay equal to the yellow line of the relay socket 5 2 USB cable 3 pin Firmware updating interface expanded function to reserve space 5 3 MIC line 2 pin Externally connect to microphone for voice monitor function 5 4 SOS line 2 pin Externally connect to SOS switch for SOS function 6 Parameter setting The SMS command format is no case sensitive and it is divided by comma There is a reply SMS after sending the command If set successfully there is a ok reply SMS or else please set again The device will reply the corresponding information after sending the SMS command Any phone numbers can send SMS command to the device as default 6 1 APN setting To connect
8. ed to set center number successfully 6 8 Delete the center number SMS command to the device to delete the center number The command is CENTER D For example CENTER D If set successfully there is an OK reply SMS Note Only SOS number can be used to delete center number successfully Only SOS Phone number can send this command successfully to set the center number There is only one center number can be set 6 9 Check parameter settings6 9settings SMS the command to the device to check the device setting Command format PARAM e g PARAM Reply information IMEI 35341 903XXXXXXxX IMEI number of the device GPRS Interval 10 GPS data uploading Interval the time ranges from 10 18000s default as 10s TIMESET 20 the GPS working time when ACC is OFF the time range from 1 999mins default as 20 min SOS Number 1 135xxxxxxxx 2 136XXXXXXXX 3 137Xxxxxxxx maximum three SOS numbers used for alarm Center Number 15942703401 only one center number used for cutting off and restoring oil command Sensor time interval 10 180 sensor detecting time default as 10s vibratio alarm delay default as 180s the time ranges from10 300s Sensor alarm time interval 10 sensor alarm time interval the time ranges from 1 60mins default as 10mins TimeZone E 8 0 set time zone default as E8 It contains IMEI number GPRS Interval TIMESET SOS CENTER number Sensor time interval Sensor alarm time Ineterval T
9. imeZone Note Only SOS number can send SMS command to set and delete center number 6 10 Check GPRS parameters GPRSSET SMS command format GPRSSET eg GPRSSET reply message GPRS ON GPRS on off status APN CMNET 0 0 0 0 0 APN setting information Server 1 egt06 szdatasource com 8841 0 platform information URL http maps google com maps q preset web link setting information 6 11 GPRS time interval6 11 The default GPRS time sending interval is 10s which means the device will upload positioning data to the platform server every 10s Users can modify TIMER time second GPRS time sending interval by SMS TIMER time second TIMER time second The time ranges from 10 18000s For example TIMER 10 It means the device will upload data to the server every 10s 6 12 Sensor alarm time setting6 12 When the vehicle power is off and ACC is in low level if ACC is off over 10 minutes the device will enter sensor alarm state In this case if the vehicle vibrates for a few times it will activate the vibration alarm system If the vehicle battery is still not on ACC is in low level after 3 minutes the device will start vibration alarm DEFENSE TIME minutes SMS format DEFENSE TIME minutes The time ranges from 1 to GSODEFENSE TIME minutes mins For example DEFENSE 15 It means when ACC is in low level for 15mins it will enter sensor alarm status vehicle power is off NOTE 1 Preset SOS nu
10. mbers when send SMS alarm messages and calls 2 If there is no need for vibration alarm please SMS SENSOR 0 to close it 6 13 Restore to factory setting FACTORYSMS command format FACTORY to set all parameter to default factoryFACTORY value Once received OK it succeeds 6 14 Reboot device When there is something wrong with the link of GPRS e g The parameter setting of the device is correct but you can t track the car on the platform At this moment you can send a command to the device to reboot the device The format is RESET After receiving this command the device will reboot after 1mins 7 Operation of device 7 1 Power on Power off Power on Once insert a valid SIM card and connect all the wires turn on the device then Power LED will flash first During signal searching process GSM and GPS LED will flash Once GPS LED keeps solid light it means the device has been located and it starts to work Power off Just turn off the power switch The device will begin to upload positioning data to server once inserting a valid SIM card and power on During the working time it can upload data to server every 10 seconds 7 2 Check location 7 2 1 Via SMS WHERE 7 2 1 1 SMS WHERE to the SIM number of GTO6 The terminal will senda location message automatically You can get the address If the device does not search any information of location it will send No data to the cell phone Exam
11. nterfere with GPS reception please drive to the open areas for positioning Generally it needs 1 2 minutes to receive the first coordinates 9 5 If GSM can not receive the signals normally please check whether SIM card is installed correctly or there is no GSM signal at the location you are such as basement parking please drive to a place covered by GSM signal reception 9 6 When cellphone with special number receives tele cutoff alarm sms please make sure whether it is illegal wire cutoff or the FUSE on power line is blown If the FUSE in it is blown please contact your distributor to exchange with the same model FUSE after the internal trouble is shoot it can be power on to work again Warranty card of GPS Vehicle tracker Special statement 1 Specifications of this product subject to change without further notice 2 Any change about the appearance and color is subject to the real object 3 Warranty card applies to the product with the IMEI number listed below 4 Please keep this card safely for after sale service as well as your receipt 5 Refer to the table below for the warranty reference This card is the basic certificate for warranty please fill it carefully and keep it safely wane one mute Address Date Invoice number Sales unit phone number 1 Main engine is guaranteed for one year for non human damage since the date of purchase 2 The situations listed below are not in the scope of warra
12. nty the user has to pay maintenance cost 1 exceed the warranty period 2 disassemble or maintain without authorization 3 immersion break or burn of circuit board damages from improper installation use maintenance or storage 4 5 damages of shell lens or internal antenna 6 IMEI number is torn or faded 7 warranty certificate is inconsistent with product model or the certificate is altered 8 the damages due to force majeure waineranoount ow n a Maintenance status E Maintenance status
13. ple Lat N22 571285 Lon E113 877115 Course 42 20 Speed 0 0740 DateTime 10 11 23 22 28 51 URL 7 2 1 2 SMS URL to the SIM number of GTO6 The device will send aURL location Google Map link If the device does not search any information of location it will send No data to the cell phone Example lt Date Time 10 11 23 23 42 51 gt http maps google com maps q N22 571490 E113 877103 7 2 3 Via platform7 2 3 Go to the platform website offered by dealers to check your vehicle location 7 3 SOS alarm In emergent case press SOS for 3s to activate SOS alarm Then the device will send SOS SMS to preset specific numbers and then dial the numbers in circles until the call is through At the meantime the device will upload SOS alarm data to the server And it will send SOSAlarm lt DateTime 1 1 06 1714 53 06 gt http maps google com maps q N22576713 E113 916585 Note The specific numbers should be preset just refer to 6 4 7 4 Wire cut off alarm When the electricity supply of device is cut off it will activate cut off alarm In this case the device will send related SMS to the specific numbers and dial the numbers in circles If nobody answers the call just keeps 3 loops at most At the meantime the device will upload SOS alarm data to the server And it will send CutPower lt DateTime 11 06 1714 53 06 gt http maps google com maps q N22576713 E113 916585 Note The specific numbers should be prese
14. rLED GPSindicator LED Status Meaning Flashing interval 0 1s Searching GPS signal Continuously in bright state GPS located Continuously in dark state GPS not located 2 4 Ignition detection indication Three blue red green LEDs are in cycling flashing 3 Interface introduction g S Tele cutoff Power interface Petrol electricity ACC interface interface Power on off a SIM card slot amp Data interface re MIC interface el Ltt ooo fl _ Z A E A TD SND AY GPS status LED GSM status LED Power working status LED Power on off SIM card slot 4 Method of installation 4 1 Preparation before installation 4 1 1 Open the packing box to check whether the type of device is correct and whether the accessories are included or else please contact your distributor 4 1 2 Choose SIM card each device needs to insert a GSM SIM card Please refer to the distributor s suggestions to choose the SIM card 4 1 3 Installing SIM card The SIM card slot is on the right side of device Open the SIM card silicon seal then insert the SIM card to the slot do not insert the SIM card backwards When the SIM card is ready you will hear a click Or else please insert again and then replace the silicon seal Note Please use GSM network SIM card Power off before installing or removing the SIM card The SIM card used should be enabled for GPRS The SIM card used should be enabled for called ID
15. s connected please turn on the ACC with key after it is connected 5 Check the LEDs status In normal working status the red LED is in solid bright or flashing green LED and blue LED are both in solid bright 6 Check whether GPS is located if not please drive to the open areas for positioning 9 2 If it is offline status in platform First of all check the three LEDs status If it is not convenient to check that please check the SIM card status 1 Call the SIM card number of the device to check whether you can get through 2 Check whether the vehicle is in no GSM area such as basement 3 Check the GSM GPS disconnection area whether it is all disconnected or few of them disconnected to make sure whether it is the fault of operator s internet 4 Check whether your SIM card charge is overdue 5 Check whether the SIM card supports GPRS 6 Check the parameter setup whether the device IMEI number GPRS sending interval is correct 9 3 If the device GPS function is normal but can not locate for a long time please check whether the installation setup of device is correct 1 Please make sure the GPS antenna face is up 2 Please make sure there is no electromagnetic wave absorbent object metal above the device especially the thermal protective coating on the windshield it may affect the GPS reception of the device 9 4 If GPS can not receive the signals normally there is high building around to i
16. t just refer to 6 4 7 5 Low battery alarm When the device is only working with battery once the internal voltage of battery is less than 3 7V device will send low battery alarm sms to specific number and alarm on platform Low battery alarm sms content example Attention battery too low please charge Which means the battery is to low to inform user charging it in time Note The specific numbers should be preset just refer to 6 4 7 6 Vibration alarm When vehicle power is off ACC status is also low and if the lead time of low ACC is more than 10 minutes settable device will activate security alarm When the security alarm is on once the vehicle vibrates for several times the alarm will be activated in the later 3 minutes vehicle power is still off ACC status is low device will start alarm At this time it will send alarm SMS to SOS specific number and dial the SOS specific number in cycle until through If nobody answers the call just keeps 3 loops at most The tracking platform will also receive vibration alarm message e g SensorAlarm lt Date Time 11 06 1714 53 06 gt http maps google com maps q N22576713 E113 916585 Note The specific numbers should be preset just refer to 6 4 SMS SENSOR 0 to turn off vibration alarm 7 7 Voice monitoring When the special number cellphone dial device ringing for 10 seconds it will enter voice monitoring status At this time caller can monitoring the
17. third number as SOS number If set successfully there is a success reply SMS 6 6 Delete specific number6 6 Before deleting specific number please check its corresponding code For the PARAM code please SMS PARAM to the device PARAM SMS command to the device to delete the number SOS D serial NO 1 serial NO 2 serial NO 3 D means to delete the number for example SOS D 1 means to delete the first number SOS D 3 means to delete the third number If you want to delete more than one numbers you can send this command SOS D 1 3 means to delete the first and third numbers If you forget serial number of the mobile number you want delete you can send this command SOS D mobile number means to delete the mobile number directly For example SOS D 13527852360 means to delete the 13527852360 directly After deleting the SOS number it will receive Delete number 135XXXXXXXX success specific number total 2 for successful deleting of the specific number 6 7 Set the center number If you want to cut off restore oil by SMS command you have to set a center number firstly Only the center number can send the cut off restore oil command to the device You can set your own mobile number as center number The command for setting center number is CENTER A mobile number For example CENTER A 15942703401 If set successfully there is an OK reply message Note Only the SOS phone number can be us
Download Pdf Manuals
Related Search