Bio Bidet IB835 User Manual
Contents
1. 3 min with level 1 of water pressure and level 5 of nozzle position will operate automatically This unit should be used under the supervision of an adult FLUSH Press FLUSH to give the toilet a flush Whenever the user presses the button the water will flush down the toilet It will operate automatically after each toilet use Remote control receiver o Power saving AUTO Press AUTO button during CLEANSE or BIDET Cleans Bidet Oscillating wash Dry will operate consecutively 20 seconds each MOVE Press MOVE button during CLEANSE or BIDET The nozzle moves back and forth to widen cleansing area Press MOVE again to release this function MASSAGE Press MASSAGE to activate rhythmical wash for massage effect Press MASSAGE again to release this function BEEPING Press BEEPING button to enable beeping sound To disable press the button again Remote control receiver Stop Bidet Cleanse DEODORIZATION Press DEODORIZATION button to activate deodorizer automatically Max 20 min When the user stands up deodorization stops after 60 seconds To disable press the button again WATER TEMP SEAT TEMP Water and Seat temperatures can be adjustable from 1 to 5 levels by pressing the buttons Both tempratures will be initalized after each use NOZZLE POSITION FR BK Nozzle position can be adjustable from 12. INSTALLING POSITION OF THE REMOTE CONTROL Install the remote control on the wall Keep the remote control in the bracket to prevent damage by dropping Area of remote control installation 27 55 AA inches 7 HOWTOUSE J o mamara AFM w mmEL 889 O gt a o UO a TTO ooj PM AM hf 8 Uspaii 7 3 A J cr NOZZLE ag Hy PRESSURE o ai jee eee fe es JI EE A STOP CLEANSE BIDET DRY KIDS FLUSH E a a ail Uspa iii dA IO MOVE MASSAGE BEEPING DEODORIZATION WATER oe STOP DRY Press STOP to stop current operation When a user stands up all operation will stop automatically CLEANSE Press CLEANSE to clean your posterior The function will stop in 60 seconds automatically Press this button again to activate oscillation The nozzle moves back and forth automatically to widen cleansing area Oscillation wash stops if this button is pressed again BIDET Press BIDET for feminine wash The function will stop in 60 seconds automatically Press this button again to activate oscillation The nozzle moves back and forth automatically to widen cleansing area Oscillation wash stops if this button is pressed again Press DRY after CLEANSING or BIDET Warm air will come out for 3 minutes To alter the strength of drying press the button again KIDS Press KIDS to change all functions to be suitable for children Cleanse 1 min Dry
3. Use the Pressure Hi and Pressure Lo Up and down arrows to change the hour and minutes e Once the time is set correctly press the STOP button to accept the changes 8 HOW TO CLEAN INTERNAL WATER FILTER CLEANING Water tank Hi Water flow valve 1 Turn water flow valve clockwise to close it 2 Turn water flow hose bidet nut counter clockwise to remove it 3 Put screen into the unit after cleaning it with a toothbrush 4 Reattach the water hose to the bidet 5 Reopen the water valve EXTERNAL CLEANING 1 Regularly wipe off the body with a dry soft cloth or sponge or dampen with neutral detergent 2 Release the lid 1 Pull left and up onthe left hinge part 2 Release the right hinge part Be aware your fingers not to be caught 3 Do not use any cleaners which are not safe to use on toilet seats Not to use Toilet cleanser Home cleanser bleach benzene paint thinner cresol etc Do not force to push pull or bend the nozzles NOZZLE CLEANING eG Ce eae MANUAL CLEAN 1 Do not sit on the seat 2 Press CLEANSE button Cleanse nozzle comes out Press the button again Bidet nozzle comes out Press FR button Cleanse nozzle comes out Press BK button Bidet nozzle comes out 3 Do not forcefully push or pull the nozzles or bend them Use a toothbrush or soft cloth to clean nozzles Press STOP FR BK and nozzles will return to stand by mode For
4. extended period of time cleaning unplugged for safety 4 Do not retract nozzles without a nozzle tip It may result in malfunction AUTOMATICALLY CLEANSE 1 Using passive cleansing simultaneously if the user pushes BK button over 3 seconds cleansing and bidet nozzles will be cleaned automatically for 30 seconds 2 Don t grab nozzle during nozzle cleansing Doing so may damage the appliance 3 If you want to stop cleaning nozzle push Stop button TOILET CLEANSING AUTOMATIC FLUSH After using the bidet the toilet will automatically flush when user stands up TO FLUSH Push the flush button on the remote to flush FLUSH WITHOUT POWER No Power is required to flush simply push the flush button on the side of the unit 9 MAINTENANCE DRAINING WATER WHILE NOT USING OVER EXTENDED PERIOD OF TIME Unplug the power supply cord Close the shutoff valve Not doing so may cause fire button PREVENTING FREEZING Make sure the power cord Set the temperature of water to low or middle is plugged in properly Freezing can be prevented by keeping the water heater on f there is no heating system in the toilet wrap pipes with cloth or other materials Not using the unit during winter season Unplug and drain the water from the water tank and pipes thoroughly Refer to the water drain method 10 CHECK THE FOLLOWING TROUBLESHOOTING GUIDE BEFORE CALLING IN FOR
5. SERVICE Check first Does the Occupied Sensor LED light up when you cover the skin sensor on the seat If the Economy Mode LED is lit the temperature settings for the seat and water will be on low Replace the remote control batteries and point the remote directly at the transmitter on the main unit PROBLEM Unit completely fails POSSIBLE CAUSE 1 Power outage POSSIBLE SOLUTION 1 Reset the GFI outlet to work or power on 2 Unit is not plugged in 2 Plug the power cord in to a GFI outlet 3 Faulty receptacle 3 Test another appliance in the outlet 4 Skin sensor is not activated 4 Activate the skin sensor on the unit Nozzle does not 1 Remote control iS not working 1 i Replace the remote control batteries i try to operate the unit with the side extend 2 Nozzle is dirty control panel 3 External bidet filter 2 Clean the nozzle 4 Skin sensor is not activated a 3 Remove the external bidet filter 5 Seat riser is covering the skin i sarisor 4 Activate the skin sensor on the unit 5 The seat riser must go underneath the bidet seat Low water pressure 1 Clogged nozzle tip 1 Clean the nozzle tip Seat is not heating Stops in the middle of use Water coming out from the nozzle unexpectedly 2 Water pressure is set to low on remote 1 Unit is set on Economy mode 2 Remote control batteries 1 Washing or drying exceeded cycle time 2 Skin sensor lost contact 3 Clogged nozzle t
6. Uspa USPA Integrated Bidet Toilet System Operating Instruction Manual Carefully read this operating instruction manual for proper use of this appliance Register Warranty for proper service If you have any questions please call us The IB 835 is just for AC 120V READ ALL OPERATING INSTRUCTIONS BEFORE INSTALLATION Notes 1 This product should be installed according to this manual 2 Read this manual carefully and install properly 3 Retain this instruction manual in an easily accessible place 4 Do not attempt to service this appliance yourself Doing so will void the warranty Table of Contents PREPARATION 1 IMPORTANT SAFEGUARDS 2 CAUTIONS BEFORE INSTALLATION 3 IDENTIFICATION 4 SAFETY INFORMATION DANGER 5 SAFETY INFORMATION WARNING INSTALLATION 6 HOW TO INSTALL 8 USE 7 HOW TO USE 12 14 ECONOMY MODE CHANGE SET TIME ETC 8 HOW TO CLEAN 15 9 MAINTENANCE 17 10 CHECK THE FOLLOWING 18 TROUBLESHOOTING GUIDE BEFORE CALLING IN FOR SERVICE ofr WO 11 SPECIFICATIONS 19 12 WARRANTY 1 Important Safeguards 1 READ ALL INSTRUCTIONS BEFORE USING DANGER To reduce the risk of electric shock 1 Do not place or store this appliance where it can fall or be pulled into a tub or sink 2 Do not place in or drop into water or other liquid 3 Do not reach for a product that has fallen into water Unplug immediately WARNING To reduce the risk of burns electric s
7. appliances in a power strip E Doing so may result in fire or damage m Be sure to use a dry and clean outlet m Do not use a faulty or loose outlet Y Do not use when the seat and lid are disassembled E Doing so may result in electric shock due to high voltage inside Do not obstruct or put anything into the dry air outlet E If the dry air outlet is obstructed with any objects it may result in fire E Ifthe dry air outlet is obstructed with hands it may result in injury Use tap potable water only Drinking water E Not doing so may cause irritation or injury to your skin Do not disassemble repair or modify this appliance Unplug when beeping or smelling strangely m Unplug right away m Contact your dealer where you bought this appliance 5 Safety Information Warning WARNING Follow basic instructions to ensure the safe use of your appliance Be aware of a low grade burn E It may result in a low grade burn if sitting on the heated seat for a long time Be aware if being used by the following Children senior citizens patients or who cannot control the grade of temperature Sleeping pills users or people who are on medication that causes drowsiness Who are drunk or very tired and may fall asleep while sitting on the unit If injured in a low grade burn see a doctor immediately Unplug while not using over extended period of time E Not doing so may result in fire injury
8. hock fire or injury to persons 1 Close supervision is necessary when this appliance is used by or near infants elders or handicapped persons Children should not be permitted to use or touch this appliance without adult supervision Be sure to adjust the toilet seat s temperature for the elders handicapped persons or people with sensitive skin 2 Use this appliance only for its intended purpose as described in this manual Do not use attachments not recommended by the manufacturer 3 Do not operate this appliance if the cord is damaged or if the product is dropped into water 4 Install the unit properly by following the installation procedure 5 Only authorized persons can install or repair the unit Do not attempt to service this appliance by yourself Doing so will void the warranty 6 Keep the cord away from heated surfaces 7 Never drop or insert any objects into any opening or hose 8 Do not use outdoors Do not use aerosol or oxygen spray products on the unit 9 Always follow the grounding instruction in this manual before plugging in the unit SAVE THESE INSTRUCTIONS 2 Cautions before installation 1 NOTE THE FOLLOWING IMPORTANT POINTS 1 Do not install in a location where water might be splashed on this appliance or in a location exposed to excessive moisture where condensation might form on the product s surface 2 To avoid damage to electronic components due to high levels of humidity provide adequate vent
9. ian or serviceman if you do not understand grounding instructions or if youdo not know whether the product is properly grounded This product is for use on a nominal 120V circuit and has a grounding plug that looks like the plug illustrated in sketch A A temporary adapter which looks like the adapter illustrated in sketches B and C may be used to connect this plug to a 2 pole receptacle as shown in sketch B if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet sketch A can be installed by a qualified electrician The green colored rigid ear lug and the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adapter is used it must be held in place by the screw Grounded ancl Adapter Grounded iida outlet box eta screw Z C Tab for S grounding screw Grounding pin 4 If it is necessary to use an extension cord use only a three wire extension cord that has a three blade grounding plug and a three slot receptacle that will accept the plug on the product Replace or repair a damaged cord 5 Remote control power AAA 1 5V 3EA CAUTION RISK OF EXPLOSION TO BATTERY IF REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS 3 Identification Main unit Lid Caution label Flush button Deodorizer Power indicatior Recepti
10. ilation by opening a window and or door when bathing 3 Water supply should have a water pressure of 11 38 psi to 106 68 psi 4 Connect the a product to pipe carrying potable water Do not connect to an industrial water line or other water supplies that are not potable 5 Cool the unit in the room before installation 6 The thermal protector in the water tank may malfunction when transporting or storing warm water 7 The rated power voltage is 120V AC 60HZz 8 Do not plug the unit in until installation is complete It may result in malfunction 2 Cautions before installation 2 WIRING REQUIREMENTS ise Any other servicing should be performed by an authorized service representative GROUNDING INSTRUCTIONS This product should be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This product is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded DANGER Improper use of the grounding plug can result in a risk of electric shock If the cord or plug is necessary to repair or needs to be replaced do not connect the grounding wire to a flat blade terminal The grounding wire can be identified by its insulated outer surface It will either be colored green or will not contain yellow stripes Check with a qualified electric
11. ip 1 Self cleaning 2 Raise the water pressure on the remote control 1 Turn off Economy mode 2 Replace batteries 3 Unplug the unit for 10 sec 1 Press the wash or dry mode again 2 Activate the skin sensor with full skin contact through the entire cleansing period 3 Clean the nozzle tip 1 The unit will self clean the nozzle before and after each use automatically CHECK THE FOLLOWING TROUBLESHOOTING GUIDE 10 BEFORE CALLING IN FOR SERVICE POSSIBLE SOLUTION POSSIBLE CAUSE PROBLEM 1 Check to make sure that all rubber washers are in place and do not over tighten the connection but it should be secure 2 Check to make sure that the rubber washer 1 Leaking from hose connection at the unit 2 Leaking from T valve 3 Leaking from behind or under the tank Water leaking continuously is in place with the flat side pointing up 3 Check that the drain is not opened on the unit if the unit continues to leak immediately disconnect it from the water supply drain the tank and contact the BBC service center 11 SPECIFICATIONS ITEM IB 835 STANDARD POWER SUPPLY 120V 60Hz 1248W Water Way of connection Direct connection to tap water supply Water pressure 11 106psi Spray for cleansing 600 100 m0 min Spray for bidet 700 100 m0 min Clean Water capacity 70 20 mQ sing Spray temperature Room Temp 104 F Heat capacity 1200W Safety feature Thermal switch Temperature fuse Floating s
12. nstalled and used in accordance with instructions We reserve the right to make inspections in order to determine the cause of the defect We will not charge for labor or parts in connection with warranty repairs or replacement We are not responsible for the cost of removal return and or reinstallation of prodcuts This limited warranty does not apply to a Damage or loss from a fire earthquake flood storm etc b Damage or loss resulting from any unreasonable use abuse negligence or improper maintenance c Damage or loss from improper installation removal repair or modification d Damage or loss resulting from sediment or other matters contained in your water system This warranty gives you specific legal rights For warranty or service information please contact your dealer where you bought this appliance or us Only the original purchaser may submit a claim under this limited warranty To activate your warranty complete this form This limited warranty is our only warranty covering your product Repair or replacement as provided under this warranty shall be the exclusive remedy available to you We shall not be responsible for loss of the product or for other incidental or conse quantial damage or expenses you may incur or for labor or other costs due to installation or removal or cost or repairs by others or for any other expense not specifically stated above Except to the extent prohibited by applicable law any implied warran
13. on Cleanse Bidet nozzle Heated seat Side control lash apash Juary Occupied sensor Accessories Hose A To the toliet 7 8 x 3 8 7 8 T valve aE IoD Tape Screw Plastic anchor Battery 3pcs 2pcs m m Qe Hose B 1 2 To the bidet 1 2 x 1 2 Conversion nut Mounting toilet Unit screw cover 2pcs screw 2pcs nut 2pcs Hose A Packed in Ceramic package 4 Safety Information Danger DANGER Follow basic instructions to ensure the safe use of your appliance S Indicates a prohibited use of the appliance Do not use a faulty or loose electric outlet or cord Indicates a required step in use of this appliance E Doing so may result in a short circuit electric shock or fire DO NOT HANDLE WITH i S PROHIBITED Q AA RAS D3 USE OF FIRE amp PROHIBITED Q DO NOT DISASSEMBLE i DO NOT GROUND CONNECTION Q REQUIRED STEP aZ 0 SPRAY WATER Do not splash water on this N Plug and unplug properly product E Do not plug or unplug with wet hands It may result in injury or short circuit E Do not grab the cord when unplugging Pull out the plug properly Do not throw anything flammable into the toilet m If avoided it may result in short shock or malfunction if no grounded wire E fno grounded plug is used make sure to install grounded wire S Q DANGER Follow basic instructions to ensure the safe use of your appliance Do not use many
14. or electric shock OK On a toilet only Improper use Do not step on or place heavy objects on this appliance Doing so may damage the unit Do not step on a lid seat or control panel to avoid injury or damage Unplug while there is thunder or lightening Do not pull out water hose forcefully E Doing so may cause water leakage WARNING Follow basic instructions to ensure the safe use of your appliance Be aware of urine splash ona nozzle or warm air outlet Not doing so may result in smelling of products or failure E Not doing so may result in fire or electric shock Le Do not sit or lean against the lid or control panel Do not force the lid to close Use the low temperature for children and disabled m If temperature settings are too high it may result in a burn due to user not recognizing the temperature Do not put a vase cup or small materials on this appliance 6 HOW TO INSTALL l Do not plug in until installation is finished completely Not doing so may damage the appliance TOILET SIZE SEAT SWITCH This product is installed with C800 toilet only It has a seat switch If you do not sit on the seat it does not work It will stop working if the user stands up during cleansing 15 74 Occupied Sensor Seat inches CONNECTING THE WATER HOSE AND GROUNDING WIRE Remove existing hose ConnectT valve to toilet fill valve Connect supplied 7 8 x 3 8 h
15. ose a from T valve to shut off valve a If your shut off valve is 1 2 use supplied 1 2 conversion nut C Connect supplied 1 2 x 1 2 hose b from T valve to bidet seat inlet m Open the shutoff valve by turning counter clockwise Check for any water leaking or dripping Water tank P t H b a 1 2 x 1 2 hose 7 8 x 3 8 hose I Main unit 4 AT C 1 2 conversion nut Using inline carbon filter Z optional The use of an external inline carbon water filter is not required unless the unit is used in an area with extreme hard water If a carbon filter is used the filter must be replaced every 6 months Inline carbon filters can be purchased from any authorized Bio Bidet reseller HOW TO INSTALL THE UNIT 1 HOW TO ASSEMBLE NUT FOR MOUNTING TOILET 1 Insert mounting pottery nuts into empty holes Refer to picture 1 2 HOSE CONNECTION AND POWER CORD ARRANGEMENT 1 Connect T Valve integrated hose to bidet Refer to 10page 2 Place power cord into the cable management areas under the bidet 3 Insert wire to wire cord home 4 Insert bidet to toilet carefully in order to keep the hose and wire cord from being damaged Mounting pottery nut Ng 3 INSERT BIDET ON TOILET 1 Slide the unit until it rests securely on the toilet 4 FASTEN BIDET ON TOILET 1 Once the bidet is placed on the toilet fasten it with the provided bolts 2 Cover bolts with white silicone angle covers 3 Pl
16. ties including that of merchantability or fitness for use are expressly limited to the duration of this warranty X Warning We are not responsible or liable for any failure of or damage to this plumbing product or product component caused by in tank bowl cleaners containing chlorine calcium hypochlorite X Note The use of high concentration of chlorine related products can seriously damage the fittings This damage can cause leakage and serious property damage For more information please contact your dealer or us Purchase Date Purchased From Full Name Amount Paid Serial Address City State Country Zip Phone Fax E mail Mail email or fax the warranty form to BBC INNOVATION SAMHONGTECH CO LTD 204 Berg St Algonquin IL 60102 2F Eunsung Building 741 Yeongdong daero Gangnam gu Phone 847 458 2334 Fax 847 854 1296 Seoul Korea E mail support biobidet com http Awww biobidet com TEL 82 2 3449 2341 FAX 82 2 3445 1686 E MAIL info isdongseo co kr http www samhongtech com Great products for your healthy living On iGo So Ox Os NG mM
17. to 5 levels by pressing NOZZLE FR BK buttons Nozzle position will be initalized after each use WATER PRESSURE HI LO Water spray pressure can be adjustable from 1 to 5 levels by pressing PRESSURE HI LO buttons Water pressure will be initalized after each use XX CAUTION Be careful not to drop your remote control in water t may stop working or cause malfunction Don t forcefully push or pull the nozzles Doing so may cause malfunction When the power is plugged in initially nozzles for feminine wash and posterior will come out in turn ECONOMY MODE e On the remote press and hold the STOP button for 3 5 seconds The unit will be in economy mode after 1 hour of last use e n economy mode temperature of water and seat will be kept to 30 degrees Celsius Eco will be displayed on the remote control LED screen next to both the seat temperature gauge as well as the water temperature gauge e When the unit is occupied during economy mode temperature will be returned original setting levels and goes back t economy mode after 1 hour of last use e Press and hold the STOP button again for 3 5 seconds again to release the economy mode function CHANGE SET TIME e On the remote press and hold the Pressure Lo down arrow for 3 5 seconds e The hour setting will begin to flash e Pressing the Nozzle FR or Nozzle Bk buttons will toggle between hours and minutes e
18. ug the power cord into the outlet 6 HOW TO INSTALL HOW TO INSTALL THE UNIT Bidet fixed area Z Toilet control area a Mounting toilet nut g 5 HOW TO CONFIRM THE FLUSHING LOCATION 1 If user pushes the flushing button after installation devices confirm the bidet and toilet are flushing properly TRIAL OPERATION 1 Preparation Plug the power cord into the outlet to fill the water tank in the bidet 2 Checking all functions Cover the toilet bowl using the plastic wrapping sheet of the unit to prevent the washing water from being sprayed out of the toilet Then check for all function described in this manual 3 Water residue that remained in the toilet may come out while heating the bidet HOW TO INSTALL REMOTE CONTROL HOW TO INSTALL REMOTE CONTROL Plastic anchor 1 Open the battery lid and insert AAA battery 3pcs 2 Check that the display appears properly 3 Make sure you can reach the remote while seated 4 Fasten the remote control bracket with double sided adhesive tape on the proper area of the wall as shown below x CAUTION Use the battery AAA 3pcs Do not use old and new batteries together and use the same type of batteries only Remote control and remote control mounting panel have a magnet Place the remote control far away from any material that can damage magnet or card Change battery if LCD is flickering or return to the start up screen THE RECOMMENDED
19. witch Seat temperature Room Temp 104 F Beaty Heater capacity 48W Safety feature Temperature fuse Deodorization method Circuit breaker Catalystic filter Within 15mA 0 03 second Length of power cord 1 5m Dimensions W 15 75 inches X L 27 56 inches X H 6 10 inches Weight 12 13 Ibs Xx Recommended water supply pressure are 11 106psi X The minimum available water supply pressure is 0 08Mpa 0 1Mpa however under 0 1Mpa pressure water spray pressure might not be strong enough Uspa If you need any help Please call us CUSTOMER CENTER 847 458 2334 BBC INNOVATION 204 Berg St Algonquin IL 60102 ZORN R R WARRANTY USPA Personal Hygiene Appliance Limited Warranty One a0 OWA We warrant our products to be free from manufacturing defects under normal use and service for a period of limited three 3 years from the date you purchase 100 Coverage of all parts and labor for the entire product for the first year from original date of purchase 75 Coverage of all parts and labor for the entire product for the second year from original date of purchase 50 Coverage of all parts and labor for the entire product for the third year from original date of purchase This warranty is only valid within the United States and Canada Our obligation to you under this warranty is limited to repair or replacement at our option of defective products or parts provided that the products were properly i
Download Pdf Manuals
Related Search