Model 3901T / 3902T / 3903T
Contents
1. note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it fo not trigger for 60 minutes or to turn on the ignition If test ing your system it is important to remember that this circuitry can cause zones to be bypassed and appear to stop work ing lf five chirps are heard when disarming false alarm pro tection has engaged If you wish to clear the memory turn the ignition key on 2007 Directed Electronics all rights reserved Diagnostics The microprocessor at the heart of your system is constantly monitor ing all of the switches and sensors connected to it It detects any faulty switches and sensors and prevents them from disabling the entire sys tem The microprocessor will also record and report any triggers that occurred during your absence Arming diagnostics If the system is armed with an input active door open sensor trigger ing etc the unit will chiro once when arming and then one more time a few seconds later This is called bypass notification note Bypass notification will not occur if chirps have been programmed OFF The system will ignore the input that was active when it was armed until it goes away Three seconds later it will monitor that input normally Disarming diagnostics Extra disarm chirps are the tamper alert If four chirps are heard when disarming the system was triggered in your absence If five chirps are heard a zone was tr2. all rights reserved Notes eee 2007 Directed Electronics all rights reserved 13 14 2007 Directed Electronics all rights reserved Ix Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet LLL QUICK REFERENCE GUIDE To arm the system M You can arm the system by locking the doors with your factory keyless entry transmitter When the system arms your will hear a short chirp and see the parking lights flash once To disarm the system Bi To disarm the system unlock the doors using your factory keyless trans mitter You will hear two chirps and the parking lights will flash twice Disarming without a transmitter Bi Turn on the ignition Press the integrated LED Valet switch the pro grammed number of times within 10 seconds The system should now disarm If it does not you may have waited too long Turn the ignition off and on and try again To enter or exit Valet Mode M Turn ignition to run position then turn to off position Press and release the integrated LED Valet switch within 10 seconds The status LED will light solid if you are entering Valet Mode and it will go out if you are exiting Valet Mode X 2007 Directed Electronics all rights reserved 15 16 2007 Directed Electronics all rights reserved 2007 Directed Electronics all rights reserved 17 The company behind this system is Directed Electronics Inc Since its inception Direc
3. MITED WARRANTY TO REPLACE OR REPAIR THE UNIT SO LONG AS THE CONDITIONS ARE MET AS DESCRIBED HEREIN Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty is void if the unit has not been purchased from Directed or an authorized Directed dealer or if the unit has been damaged by accident unrea sonable use negligence Acts of God neglect improper service or other causes not arising out of defect in materials or construction This warranty is only valid for sale of product s within the United States of America Product s sold outside of the United States of America are sold AS IS and shall have NO WARRANTY express or implied This product warranty is automatically void if its date code or serial number is defaced missing or altered This warranty will not be valid unless you have completed the warranty card and mailed it to Directed within 10 days after purchase to the address listed on the warranty registration card Make sure you have all of the following information from your authorized Directed dealer A clear copy of the sales receipt showing the following o Date of purchase o Your full name and address o Authorized dealer s company name and address o Type of system installed o Year make model and colo
4. There are different security levels which can be selected as follows Step Lock Button Number of Siren Armed State with pressed Chirps Zone Bypassed Twice 3 Chirps 3 flashes lZone 2 8 4 Bypassed return to step 1 The user can repeat the steps provided the LOCK button is pressed between 3 and 7 seconds and no other buttons are pressed Bil If the Lock button is pressed again anytime the system will 2007 Directed Electronics all rights reserved 5 Disarming To disarm the system unlock the doors using your factory keyless trans mitter The siren will sound twice and the parking lights will flash twice If the siren sounds either four or five times when disarming refer to the Diagnostics section of this guide This is called Tamper Alert Disarming without a transmitter This feature allows you to override the system without the transmitter should it be lost damaged or disabled To do this you must have the ve hicle s ignition key and know where the integrated LED Valet switch is located The Valet switch is activated by pressing the LED status indicator Integrated J LED Valet switch LED status indicator Turn the ignition to the run position Q Press and release the integrated e LED Valet switch within 10 seconds After a few seconds the LED will stop flashing and the vehicle should start If it does not you may have waited too lon
5. Vehicle Security System Model 3901T 3902T 3903T Owner s Guide limited For a period of one calendar year from the date of purchase of this auto security device Directed Electronics Directed promises to the ORIGINAL PURCHASER to repair or replace at Directed s election with a comparable reconditioned model any Directed unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use provided the following conditions herein Conditions are met the unit was purchased from an authorized Directed dealer the unit was professionally installed and serviced by an authorized Directed dealer the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer and the unit is returned to Directed shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information consumer s name telephone number and address the authorized dealer s name telephone number and address complete product description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF PURCHASE WILL BE DENIED After the first calendar year from the date of purchase of the unit Dir
6. ected promises to the ORIGINAL PURCHASER to repair or replace at Directed s sole and absolute discretion with a comparable reconditioned model any unit which proves to be defective in workmanship or material under reasonable use FOR A CHARGE OF 45 00 SO LONG AS THE AFOREMENTIONED CONDITIONS HAVE BEEN MET The unit must be returned to Directed postage pre paid along with a legible copy of the receipt including the information below and a cashier s check or money order made payable to Directed Electronics in the amount of 45 00 This warranty is non transferable and is automatically void if the unit has been modified or used in a manner contrary to its intended purpose or if the unit has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or construction This warranty does not cover damage to the unit caused by installation or removal of the unit This warranty does not cover labor costs for the removal diagnosis troubleshooting or reinstallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorized dealer to obtain the service charge for your unit These security systems are a deterrent against possible theft Directed is not offering a guarantee or insuring against vandalism damage or theft of the automobile or its parts or contents and Directed hereby disclaims any liability whatsoever including withou
7. g Turn the ignition off and try again note The setting for the number of times the integrated LED Valet switch must be pressed is set in the Programming Section of this guide 6 2007 Directed Electronics all rights reserved Valet mode You can prevent your system from arming by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the system will not arm even with the transmitter but all con venience functions door locks trunk release etc will work normally To enter or exit Valet Mode with the integrated LED Valet switch Turn the ignition to on position then turn to off position Press and release the integrated LED Valet switch within 10 sec onds The status LED will light steady if you have entered Valet Mode To exit Valet Mode repeat the steps above The LED will turn off when exiting Valet Mode Panic mode If programmed On Step 3 2 If you are threatened in or near your vehicle you can attract attention by triggering the system with your transmitter If your factory keyless transmitter does not have a panic button this system can be pro grammed to enable a panic feature refer to the Programming Options If enabled just press the lock button on your factory keyless transmit ter twice more than once within three seconds 7 seconds to enter Panic Mode 2007 Directed Electronics all rights reserved 7 The siren wil
8. icroprocessor which monitors your vehicle and controls all of the alarm s functions Failsafe Starter Kill if equipped An automatic switch controlled by the security system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet Mode or should the starter kill switch itself fail Your system is ready for this feature how ever installation of this feature may require additional labor Input Any physical connection to the security system An input can be provided through a sensor pinswitch or by existing systems in the vehi cle such as ignition or courtesy lights Integrated LED Valet Switch A small push button switch with an integrated LED mounted somewhere in the vehicle The switch is used to override the alarm when a transmitter is lost or damaged or to put it into Valet Mode The LED indicates the status of your system It is also used to report triggers and faults in the system or sensors This switch is also used to program optional features Warn Away Response Light impacts to the vehicle generate the Warn Away Response which consists of several seconds of horn honks and flashing parking lights Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone 12 O 2007 Directed Electronics
9. iggered so many times that false alarm prevention circuitry has bypassed that zone In either case the status LED will indi cate which zone was involved see Table of Zones section The system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time the ignition key is turned on 10 O 2007 Directed Electronics all rights reserved Table of zones The zone number is the number of LED flashes used by the system to identify that input The standard input assignments are listed below ZONE Number LED Flashes DESCRIPTION 1 Trunk hood opening 2 Heavy impact detected by the shock sensor 3 Door switch trigger 4 Optional sensor 5 Ignition input 6 Extra switch input if installed The LED will not report if the Warn Away response is triggered Rapid resume logic This system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is dis connected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode 2007 Directed Electronics all rights reserved 11 Glossary of terms Control Module The brain of your system Usually hidden under neath the dash area of the vehicle It houses the m
10. l sound and the parking lights will flash for 30 seconds To stop Panic Mode at any time press the unlock button on your factory transmitter note The system can also be programmed so that pressing the lock button more than once within three and five seconds will activate an optional accessory If the unit is programmed fo activate an optional accessory Nuisance Prevention Circuitry Your system has Nuisance Prevention Circuitry NPC This circuitry prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Here s how it works The alarm triggers three times Each time the same sensor or switch Is triggering the alarm The three triggers are within 60 minutes of each other Your system will interpret this pattern of triggers as false alarms After the third trigger your system ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continuously triggering will remain bypassed Doors are covered differently If the alarm is triggered by an open door 8 2007 Directed Electronics all rights reserved for three full cycles one and one half minutes the doors will be bypassed until the trigger ceases
11. r of the automobile o Automobile license number o Vehicle identification number o All security options installed on automobile ii O 2007 Directed Electronics all rights reserved Contents Limited consumer warranty i Trademarks and copyrights 1 What is included 2 Important information 2 Using your system 3 Arming your system 3 Armed protection 4 Disarming an aver se D ers tee 6 Disarming without a transmitter idus As cto Edicte 6 Valet mode ice eer ES 7 Panie ModE oo mean 7 Nuisance Prevention Circuitry 8 Diagnostics 10 Arming diagnostics 10 Disarming diagnostics 10 Table of zones 11 Rapid resume logic 11 Glossary of terms 12 NOTES cc endo etu eun 13 Trademarks and copyrights Code Hopping Directed Doubleguard FailSafe Nuisance Prevention Circuitry NPC Silent Mode Soft Chirp Stealth Coding Stinger Valet and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics Inc 2007 Directed Electronics all rights reserved 1 What is included e Control module and harness A Stinger dual stage shock sensor on board the control module Pre wired Valet switch with integrated red status LED Failsafe Starter Kill relay if equipped Important information Congratulations on the purchase of your securi
12. s Heavy impacts will trigger the system The triggered sequence is 30 or 60 seconds of constant siren sounding and flashing parking lights If a door is opened the system will immediately start pulsing the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progres sive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the sys tem is armed while still providing instant response even if the door is immediately closed note If programmed for instant trigger the siren will output full trigger response after the door has been opened see Programming Options Turning on the ignition key triggers the same progressive response as opening a door If equipped the starter interrupt prevents the vehicle s starter from cranking note The vehicle may already be equipped with a starter interrup relay from the factory 2007 Directed Electronics all rights reserved Multi level security arming If programmed ON Multi Level Security Arming allows the user to select sensors to be active or bypassed when the system is armed Multi Level Security Arming can only be accessed if the function is set ON option 3 2 By pressing the LOCK button more than once within 3 and 7 seconds of arming the system activates Multi Level Security Arming If the LOCK button is pressed again the unit cancels the bypass of the sensors
13. t limitation liability for damage vandalism and or theft of the vehicle parts and or its contents Directed neither assumes nor authorizes any person or entity to assume for it any duty obligation or liability in connection with its products Directed disclaims and has absolutely no liability for any and all acts of third parties including its authorized dealers or installers In the event of a claim or a dispute involving Directed or its subsidiary the venue shall be in San Diego California 2007 Directed Electronics all rights reserved i California state laws and applicable federal law shall apply and govern the dispute TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES ARE EXCLUDED INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE UNIT DIRECTED SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOWING REPAIR REPLACEMENT DAMAGE TO VEHICLE DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITH STANDING THE ABOVE MANUFACTURER DOES OFFER A LI
14. ted Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology DIRECTED is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers Lixected ELECTRONICS Directed Electronics Inc Vista CA 92081 www directed com 2007 Directed Electronics Inc All rights reserved G3901T 3902T and 3903T 2007 09 18 2007 Directed Electronics all rights reserved
15. ty system Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with a preprinted dealer certificate to verify that they are authorized By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print additional or replacement copies of this manual by accessing the Directed web site at www xpressvip com 2 O 2007 Directed Electronics all rights reserved Using your system Arming your system You can activate or arm the system by locking the doors with your fac tory keyless entry transmitter When the system arms you will hear a short siren sound and see the parking lights flash once While the sys tem is armed the status LED will flash about twice a second showing that the system is actively protecting your vehicle If you hear a second short siren sound after arming and see the status LED flashing in groups see Diagnostics section This extra short siren sound is called Bypass Notification This means a zone such as a door or trunk is open 2007 Directed Electronics all rights reserved 3 Armed protection When armed your vehicle is protected as follows Light impacts to your vehicle will trigger the Warn Away sig nal The system will pulse the horn and flash the parking lights for a few second
Download Pdf Manuals
Related Search