INSTALLATION OPERATION MANUAL
Contents
1. ON OFF Control the power on and off In manual mode it also controls the ON and OFF for circulation pump LAMP Turn on and turn off the underwater light 03 Manual control the ON and OFF of ozonator T3 Set the third circulation period T2 Set the second circulation period T1 Set the first circulation period T ON To set the starting time of circulation period T OFF To set the ending time of circulation period 4 9 10 USER MANUAL FOR WTP 25 POOL FILTER Set the clock and increase time A M The switch of manual mode and automatic mode 11 Set the clock and decrease time e ee eee Instructions for manual operation Press ON OFF key to make the power on and the control system is ready to run Press A M to start the manual mode the indicator light on it is off In manual mode press ON OFF key to turn on and turn off the circulating pump Press the LAMP key to make the underwater light on the indicator light on it will be on NOTE Press all the above keys again to make the functions off Instructions for automatic operation Press ON OFF key to make the power on and the control system is ready to run Press A M to start the automatic mode the indicator light on it will show RED In automatic mode when the current time is during the period of set time the indicator light on T ON will be on when the current time is out of the period of se2. the minute number will stop flashing and be saved automatically If need to adjust the hour press T1 key again with 3 seconds to start setting the hour Press A and Y keys to adjust the hour the hour number on LED screen will flash No action within 3 seconds the minute number will stop flashing and be saved automatically PLEASE SET T2 AND T3 OPERATING PERIOD LIKE ABOVE OPERATION REMARK if no need to set the time in any of the 3 periods just set the time to zero in that period to avoid it Cautions before first using Before running the device for the first time turn on the ball valve of the pipe and fill water until the equipment box pipe are full of water and then turn off the ball valve When it is ready to start running press the ON OFF key on control panel for several times until the circulation pump can work normally because there may be some air inside the pipes and pump for first running USER MANUAL FOR WTP 25 POOL FILTER 3 Setting device running Manufacturer recommends running time water temperatur 2 h For example Recommending to set time as 8 00 20 00 if water temperature is 24 C then the running time is 24 2 12hours The device can do filtering at night time if noise pollution is not considered TROUBLE SHOOTING PROBLEM REASON SOLUTION l Filter bag is removed Pump is running but filtering Filter effect is not good i the drums am
3. WIP 25 POOL FILTER INSTALLATION OPERATION MANUAL USER MANUAL FOR WTP 25 POOL FILTER KNOW YOUR PLANT Name of parts Water outlet Underwater light Plant box Water inlet Water outlet Under water light Fig 1 Front View WTP 25 FILTRATION SYSTEM WTP 25 FILTRATION SYSTEM INCLUDES TWO PARTS FILTER AREA is immerged in the swimming pool with underwater light It includes 1 skimmers 2 jets 2xFiltering drums and union pipes TECHNICAL HOUSE is located in the concrete pit which is behind the panel or pool wall It includes 1 circulating pumps 25m h and the pipe which connects to the Filter Area And the ozonater pipe is also in the area Swimming pool water goes into the 1 skimmer active door of the filter area go through the 2 filter drums into the pumps and then return to pool via the jets The pumps can be controlled manually or automatically by the digital timer Optional RF Remote control The features of the filter system are as follow High filtration power 25m h easy installation safety cost effective and easy maintenance 2 filter bags precision is Sum I high suction skimmer removes pool surface pollution effectively 2 USER MANUAL FOR WTP 25 POOL FILTER Pipe free no plant room low pump power consumption LED underwater light low power consumption 18w Inter cooling system hot air is removed from the technical house by vacu
4. ce Only parts from the manufacturer will ensure smooth running of the filter Any foreign parts installed without approval will cancel the manufacturer s warranty When working do not insert amp pull out connect or do other operation It is better to ask authorization personnel for maintenance and repair Please read this manual before maintenance and repair Please contact the manufacture or the nearest dealer when there is incorrect operation or damage 2 NOTES FOR INSTALLATION AND ASSEMBLY Before connecting the cable to device please check if it is installed and connected correct Very important do not let device and electrical parts get wet when the electricity power is on 3 NOTES FOR STARTUP Check the cable operation location and others before start up Do not start filtration function if the water line is not high enough 4 NOTES FOR MAINTENANCE Make sure the power is OFF when opening the technical house cover 5 NOTES FOR USAGE Do not stand on the filter cover Do not let children open the technical house optional locking device Do not use device as springboard
5. p blocked bag is Pump is working but ig water Greulation ir bubbles pockets in Pump piping Filter basket is blocked Put back the filter bags replace Filter bag is not placed correctly infwith clean bags dirty Check if filter bag is installed correctly Open inlet valve and fill with water or start stop the pump a few times to flush out the air Clean filter bag Clear out the leaves and garbage of the filter basket Pump is working but the water flow is small Water line is too low Fill up the pool to 3 4 skimmer Incorrect voltage Check the voltage of power supply Take out front part of jet to check for debris Water is found on the bottom of the technicaljPump pipe or union part is leaking Water is founded inside the light Tighten the pump union re seal the connection pipe Change a new light Transformer no work Wrong wire connection Check if the outlet of transforme is 12V Check if the main power is closed Turn no the device but i Outside set filtration time T1 T2 T3 can not work Switch to manual mode check i the device can work USER MANUAL FOR WTP 25 POOL FILTER SAFETY 1 ROUTINE The device is limited to be used in tap water The filter is limited to be used for swimming pool water treatment and prohibited to be used for other water treatment Periodical checking is necessary Please contact the supplier before you refit any part of the devi
6. t time the indicator light on T OFF will be on When the manual mode is cancelled the circulation system will be controlled by the preset time in each use Set system clock Long press A M key for 3 seconds and loosen the hand the panel will display system clock time and hour minute digit flashes Press to adjust the clock time It will store and return to the previous working status after flashing 3 seconds Setting the first operating period in automatic mode press T1 key to starting setting the first on operating period Press T ON key the indicator light on it will be on within 3 seconds after press T1 key to start setting the starting time for the first period Press A and W keys to adjust the minute the minute number on LED screen will flash within 3 seconds after press T ON key No action within 3 seconds the minute number will stop flashing and be saved automatically If need to adjust the hour press T1 key again within 3 seconds to start setting it Press A and W keys to adjust the hour the hour number on LED screen will flash No action within 3 seconds the minute number will stop flashing and be saved automatically Press T OFF key the indicator light on it will be on to start setting the end time within 3 seconds Press A and W keys to adjust the minute the minute number on LED screen will flash No action within 3 seconds
7. um suction created by the water jets Filter bag is easy to clean using high pressure water Recommend WTP 25 is to recommend to be used for new swimming pool and renovation pool Technical specification Power supply 220V 50Hz Underwater light 18w 12V Power consumption 1 6kw Pump outlet D40mm Flow rate 25cbm h Pump inlet 040mm Ozone Generator 500mg h Dimension 1540 760 1020mm Filtration precision lt Sum Net weight 65 kgs INSTALLATION INSTRUCTION 1 Layout to put the plant NOTE before the paving of the pavement of the swimming pool please connect a anti corrosive and waterproof electrical cables of 3x4mm L N G from the residual current device RCD of power supply 8A 220V 50 60Hz which is our requirement to the connection box of this plant 1540 SZ XXXXXXXMXI NANNA LRR ANUS 0801 Fig 2 Dimensions 3 USER MANUAL FOR WTP 25 POOL FILTER II Electrical installation instruction NOTE Electrical installation must be operated by the qualified technician Lamp Gireulaten PUMP Power supply Lg DH AC12V AC220V AC220V Tansformer 94 Control panel Ozone generator Wiring of control box Fig 3 Wiring of control box OPERATION INSTRUCTION FOR DIGITAL CONTROL PANEL 2 3 4 5 6 Ta 8 Fig 4 control panel
Download Pdf Manuals
Related Search