Electronic TX-700
Contents
1. Electronic TX 700 Stringing Machine User s Manual Attention Please read this manual carefully before operating with the machine Keep it properly for the aftersales service Page 1 Catalogue 1 Attentions 1 1 Operating attentions 1 2 Safe using attentions 2 Unpacking and inspection 2 1 Components 2 2 Inspection 3 Operating Instructions ss cc 5 4 Mounting a racket ss 6 5 Insertastring ss 7 6 adjusting the base of the swivel camp 7 7 Maintamce CCj C C O Oa a 8 8 Troubleshooting y Y y y C 8 9 Service Guide y C C Oaall a 9 10 Calibration 10 Page 2 Safety precautions Following are fatal informations for your safety please observe strictly Warning mark Any information in this manual with a warning mark must be abided by strictly otherwise there will be danger of the personal safety or could lead to a significant accident CPP Forbidden mark Any information in this manual with a forbidden mark must be abided by strictly otherwise there will be danger of the personal safety or could lead to damage of the machine 1 1 Warning Z Do use 220v AC power and the provided cable and plug Please make sure the power match the machine in the play court Do not disassemble or change the machine voluntarily otherwise it will damage the machine or cause serious accidents Z Do not use the machine close to volatile or flammable gas A Do keep away from heat prevent p2. H f g r L p t top A t f g f d hret d whe P F pe Ps fy F if l FF f 0 d c L Cs Ji Jen vif m_m Page 7 7 Maintenance NO nA A W 8 2 The Electronic TX 700 stringing machine is adjusted and calibrated before shipment Working is easy and relatively maintenance free Keep the stringing machine always at a dry and safe place Keep it away from dust grease moisture and any type of heat Clean the dust and other dirt with a soft cloth or brush Water should never come inside the machine Do not use liquid cleansers abrasive cleaners or aerosol cleaners Use fine emery cloth to remove the wax buildup from the jaws of the clamps and the string gripper Do not uses sandpaper to remove the wax buildup it will destroy the special finishing Do not lubricate the tracks of the turntable Do not use penetrating oils to clean or to lubricate 10 Check the clamps often to be sure that they hold the string properly I not adjust them as shown before 11 Reset the tension setting to 10 kilograms after stringing 8 Troubleshooting The power light does not shine and the electronic part does not do anything Be sure the power switch is in on position Check that the power cord 19 properly installed Check the fuse Turn off the power switch and unplug the power cord from the wall outlet before checking the fuse The fuse housing 1s next to the power switch Check the wall outlet
3. ackaging materials for the event that reshipping is required d e aa j 4S pro _ E poea lt i AT 1 m Page 4 3 Operating Instructions 1 Place the machine on a table or a stand foot 2 On the back side of the electronic tension there is a switch which should be in the ON position for normal operation 3 Turn the power on and a red light flashes and the tension strength appears on the LED display 4 Select the tension scale in kilograms or pounds on the left beside the display The machine is always shipped set to kilogram 5 Now turn the knob on the right side of the Electronic tension head to select the tension you require to string your racket The machine is very sensitive so it may be not so easy to select 6 The stringing machine has 3 positions re Machine Stops I Machine pulls to the selected tension P EE Machine moves back to the starting position Page 5 7 If the string is not released then press the green button the string gripper will rotate one total round 8 After stringing turn the machine off 9 Turn the tension on the display down to 10 kilogram the tension in the machine should be as low as possible in the time of not stringing 4 Fixing of the Racket Loosen both mounting stocks place the four K shaped side supports into the hole of the side support arms in the far outer hole for tennis rackets in the other hole for badminton and squas
4. h Now place the racket in the middle of the stringing machine Ensure that the two swivel clamps can reach all of the racket area for stringing Never apply excessive force or over tighten the mounting stock locking knobs this will damage the parts Tighten now the side support arms and the mounting stock but be careful not to do this too heavily that the racket will not be deformed Page 6 5 How to put the string into the tension system First place the string over the small reel and then around the big one and place it into the slot and hold the string down Then push the button to 1 and the machine starts pulling until it has the right tension 6 Adjust the Base of the Swivel Clamp to the correct holding pressure If the Clamp base is no longer working very well put the clamp base vertical to the track Insert the 3mm Allen wrench into the hole on the side of the base before you have to remove the black cap Then turn it only slightly clockwise do not use excessive force this could damage the base It can be very difficult to turn Then put the Allen wrench out of the base and test if it is working well again if not repeat the process again Do not adjust on the base of the clamp base Only at this screw fa z r if gt f FF 47 ba N d L i j L a d d A lt lt d P 1 H i RE e a eu ee K aiin Geah oO i 1 ens 7 4 a J A t D mTl a a wre a g P nA or gt Fa S
5. ning it will be not so easy because there is a transport protection on it 6 Then pull again and check the result 7 If the result is ok it is finished if not repeat this procedure until the result is Ok Page 10
6. utting the machine under the sun for long time avoiding the plastic and rubber parts become aged Do contact with local service provider or manufacturer If the machine has an unusual situation for example big noise strong smog and leakage please cut the power immediately Z Do unplug the power plus when the machine is not in use or renew parts 1 2 Forbidden Do not let the kids play with the machine or power equipment Do not touch the inner parts when the machine is operating or it will cause an accident Do not let the kids operate the machine when cleaning up interior of the machine in order to avoid damaging the machine or causing any danger Do not operate the power or machine switch with barefoot or wet hands Do not move it during working 0 Do not clean the surface of the machine with volatile wet cloth Do not putting it aside in moist or other bad environment Do not placing the cable in high temperature or beside the heating Page 3 Unpacking and inspection The machine is delivered ready assembled 2 1 Components 4x T054 racket frame support 2x T025 universal clamp Ix Co AC power cable Set of 7 2 2 Unpack the machine carefully and inspect the Electronic TX 700 stringing Allen wrench machine for any obvious damage Check if all parts are included in the carton If any item is missing or damaged contact your delivery agent and your sales representative Retain the original p
7. with another electronic equipment Page 8 The string clamp does not hold the string e Clean the jaws of the string clamp e Adjust the clamp on the top The string slips through the string gripper e Clean the string gripper like described before The clamp does not move smoothly or can not be fixed e Clean the tracks of the turntable e Adjust the swivel clamp base per instruction The tension pulling is not correct e Calibrate the machine e Is the string not fixed in the clamp e Is the clamp base moving 10 Service Guide Service notice If there is problem during the using time please call our service hotline or send an email Please do provide us bar code or detailed order consignee and the date of purchase Page 9 11 Calibration The machine is calibrated with an electronic Tension calibrator if you have only a mechanic one please be sure that it is not too old otherwise the spring inside will give you wrong results Tension Calibrator 1 Set the tension to 25 kg 2 Fix the tension calibrator with one end at the mounting post and the other into the string gripper 3 Start pulling and check the result on the tension calibrator 4 If the result is not correct you have to readjust the machine 5 Beside the display are two little holes take a small screwdriver put it into the upper hole and turn inside a little to get the same tension at the display and the tension calibrator At the begin
Download Pdf Manuals
Related Search