User Manual
Contents
1. R NET www chasswheel com 44 rev 1 2014 05 08 2 EQUIPMENT AND THEIR USE SAFETY BELT USE The Stand Support System is equipped with a 4 point safety belt The use of this is always recommended whilst sitting in the wheelchair and must absolutely be used whilst using the Stand Support System The safety belt must always be adjusted as suitable for the user KNEE SUPPORT USE Included in the Stand Support System is a knee support which is to always be used during the operation of the Stand Support System The knee support is attached by connecting the triangular hooks that are at the end of the knee Support strap to notches that are located on the front corners of the chair Ensure that the hooks are attached behind the slide preventer The knee support is adjusted by a sliding adjustment band The adjustment band has velcro fastening The knee support is adjusted correctly when it is snapped underneath the kneecap A loosely attached knee support does not give enough support whilst in the erect position SEAT OPERATION ADJUSTMENT The wheelchair seat is adjusted by pressing the MODE button whereupon the picture of the adjustment appears on the screen The seat part which is seen darkened in the picture is at that moment adjusting Adjustment happens by moving the guidance stick forwards and backwards Choosing the different parts of the seat occurs by moving the guidance stick to the right and left sides by quick movements By press2. 2 ASSWHEEL Possible OWNER S MANUAL Read the manual carefully In matters that are unclear we request that you contact us Chasswheel Oy Myllyharjuntie 6 71800 SIILINJARVI Tel 358 207 559 220 Fax 358 207 559 221 LE mo ISO 7176 19 Wheelchair Valued CW4 FOUR X DL user We welcome you among CW3 FOUR X DL users We appreciate your confidence in us and we are convinced that your recently received electric wheelchair will fulfil your expectations The most important aims in the planning and manufacture of the CW4 FOUR X DL are to offer the freedom to move for every person and thus improve their quality of life Your CW4 FOUR X DL electric wheelchair guarantees you a smooth ride both on and off road Now there s no need to plan your route according to where your wheelchair can get but you can now go wherever you wish The CW3 FOUR X DL goes agilely up and downhill and climbs up street kerbs easily Snow mud or tree roots are no longer obstacles for you By paying attention to our user s manual you will learn how to use the CW4 FOUR X DL electric wheelchair safely for your long term benefit We wish you pleasant riding on the CW4 FOUR X DL R NET www chasswheel com 2 rev 1 2014 05 08 WARRANTY Chasswheel Oy guarantees a two 2 year warranty for the CHASSWHEEL CW4 FOUR X DL electric wheelchair s frame and chassis the driving control system driving motors and the seat Batteries and charging appliances are
3. 2 pcs x 12V Linak 28 S steel stove enamelled powder paint 2 shock absorbers I steering attenuator R NET rev 1 www chasswheel com 36 10 SERVICE CARD OF FOUR X DL WHEELCHAIR Frame no Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done by gt Date and place _ gt gt gt O Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done by Date and place _ gt O H R NET www chasswheel com 37 rev 1 2014 05 08 Frame no Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done by _ ___ gt gt gt Date and place _ gt gt O Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done Dy Date and place _ gt gt O a a aa R NET www chasswheel com 38 rev 1 2014 05 08 T Frame no Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done by Date and place Annual maintenance Yes _ No Additional maintenance if needed Notices if needed Maintenance done by Date and place a R NET www chasswheel com 39 rev 1 2014 05 08 T Frame no Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done by Date and place Annual maintenance Ye
4. are the following Current Profile Battery Indicator Profile Name speed Indicator ndoor Drive Battery indicator The picture shows the battery s charge level High number of dark pillars indicates good charge level If the icon flashes slowly the battery charge level is low and they should be recharged immediately When the batteries are recharging the pillars will be darkened from left to right The wheelchair cannot be used until the charger has been detached from the charger socket and the drive controller has been Switched off and back on III Speed indicator This icon indicates the maximum speed As the number of dark columns increases so does the maximum speed The maximum speed can be adjusted using the maximum speed adjusting switch Current profile d The profile number and name indicates the profile currently in use Indoor Drive R NET www chasswheel com 14 rev 1 2014 05 08 In Focus If the wheelchair has another driving controller such as a secondary x Joystick Module or a Dual Attendant Module the InFocus symbol is d displayed The icon indicates that the primary driving controller is not in control Restricted speed If the speed of the wheelchair is limited because of a sharp turn raised seat the stand support or lift function etc this symbol will be displayed If the wheelchair is inhibited from driving the symbol will flash Restart When the Restart icon flashes
5. between the rim halves Now fill the tyre a little bit 0 5bar to get the inner tube straight After this install the tyre onto the motors hub with coach screws When tyre is attached to the motor fill up the tyre approx 3bar is reasonable After this remove lifting equipment and the chair is ready to drive again DISCONNECTING THE BATTERIES Detach the cables and and the main fuse from the batteries using 11mm open ended spanner Open the attachment straps Lift the batteries from the casing Use only gel batteries Suitable gel batteries for Four X wheelchair the user can get from the Four X distributor Chasswheel part number Gel battery 73Ah Notice If you have old or possibly damaged gel batteries please handle them very carefully and not with bare hands because there might be a risk of leaking Deliver the batteries to the hazardous waste disposal point or your Four X service agent INSTALLING THE BATTERIES Install the batteries in the casing pole on the wheelchair s right side Tighten the connection straps Install the cables red blue Install the main fuse case Check that all the connections are tight Pole grease can be used to prevent oxidisation Set the battery container cover in place and tighten the breather screw R NET www chasswheel com 30 rev 1 2014 05 08 CHANGING THE LAMPS FRONT LIGHT REAR LIGHT Unscrew screws located behind the lamp In rear lights screws for rubbe
6. must be observed On an inclined surface driving in the erect position is absolutely forbidden due to the dangers of overturning Do not use the appliance if you suspect that some part may be broken but deliver the appliance directly for servicing Before raising to the upright position ensure that the safety accessories are properly attached The appliance is installed with a speed limiter which halves the maximum speed automatically when the upright position raiser operation is used If you suspect that the limiter is not operating properly do not use the Stand Support System but contact service When inclining the back backwards in the sitting position or lowering to the lying position take care that the upright position raiser appliance does not create pressure on the battery compartment This can cause the seat s spindle motor or battery compartment to be damaged When using the Stand Support System ensure that the foot support can move freely In a case that the foot support catches on the floor an obstacle or an axis stop operations and adjust the various sections of the seat until the foot support is freed The foot support is generally released by adjusting the seat downwards or by adjusting the centre of gravity backwards An obstruction to the foot support may result in breakage of the spindle motor used in the foot support adjustment Do not push the wheelchair Use the drawstrings for transferring the wheelchair
7. not included in the warranty On every wheelchair there is a model plate which shows a unique serial number This warranty covers faults that occur in normal operation of the wheelchair The warranty does not cover faults caused by normal wear and improper or lack of maintenance as indicated in the owner s manual and the service instructions Furthermore the warranty does not cover faults originating from overloading or incorrect programming Normal wear occurs in parts such as tyres rubber mountings leaf springs joints and Slide surfaces Increased noise of the driving motors is also caused by normal wear Indirect expenses incurred in dealing with faults are not included in the warranty Wheelchair frame number Date and signature R NET www chasswheel com 3 rev 1 2014 05 08 DECLARATION OF CONFORMITY CE The manufacturer Chasswheel Oy Myllyharjuntie 6 71800 SIILINJ RVI Finland declares that the CHASSWHEEL CW3 FOUR X DL electrically powered wheelchair conforms to the following standard requirements 93 42 EEC EN 12184 Siilinj rvi 8 7 2009 Risto Heikkinen Managing Director R NET www chasswheel com 4 rev 1 2014 05 08 CONTENTS LAFE TY RECOMMENDATIONS eae ease tae ete tae cleanse en ate oa da eden calender een nde een eaten irene 6 APPLICABILITY FOR DIFFERENT TYPE OF USERS 6 NFE DRIVING EE 6 SAFE USE NND SERVICE aere E E NEE E AEEA N E VA E NEN E 8 2 FEOUIPMENT AND THEIR USE E 11 2 1 DRIVING CONTROLLER
8. rev 1 2014 05 08 EH Take note of the battery charge level before and while driving Always recharge the batteries when possible The wheelchair s standard charging equipment will not overcharge the batteries The wheelchair operations may be disturbed in electromagnetic fields which may be emitted by e g mobile phones or other similarly emitting equipment The wheelchair itself can disturb equipment based on electromagnetic fields such as shop alarm systems Dont leave the wheelchair under the straight sun light Metal parts and surfaces of the wheelchair for example the seat and the cushions of the armrests might heat easily Also avoid leaving the wheelchair under high freeze After driving under moisture circumstances take care of drying the wheelchair for example by storing it in a warm space Do not leave the wheelchair outside or in cold and moisture spaces Not following these instructions might damage the wheelchair SAFE USE AND SERVICE The wheelchair s driving controller has factory settings which are suitable for most users It is possible to change some of these settings Programming should only be performed by healthcare professionals with adequate knowledge of the controller system Incorrect programming can create dangerous driving properties or damage the controller system The reliability of the wheelchair and the control system is improved if you keep exposure to extreme conditions to a minimum Damaged wheelchai
9. screws 2 When the Suitable position has been found retighten the screws The arm rest height and angle are adjusted with a 5mm hexagonal key Adjusting the height is performed by loosening the screw A and moving the arm rest up and down When the height is suitable retighten the screw R NET www chasswheel com 18 rev 1 2014 05 08 For the adjustment of the arm rest angle the support is raised to an upright position The angle is adjusted by turning the screw B until the suitable position is found R NET www chasswheel com 19 rev 1 2014 05 08 ADJUSTMENT OF A MANUALLY ADJUSTABLE FOOT REST The distance of the leg support from the chair is adjusted by loosening the retaining knobs 1 in front part of the seat When the correct distance is found retighten the screws The length is adjusted with a 5mm hexagonal key 2 The foot rest angle 3 can be adjusted with a 13mm open spanner The foot rest is adjusted by raising the lever 4 which releases the lock and the position can be adjusted When the correct position has been found release the lever The foot support is now locked into this position It is necessary to observe the foot rest position when driving uphill or negotiating obstacles Repeated striking of obstacles on the foot support may damage it ADJUSTMENT OF AN ELECTRICALLY ADJUSTABLE FOOT REST WITH LENGHT COMPENSATION Adjustment of distance length and the foot rest angle is carried out similarl
10. suitable for most users By reprogramming you can change the joystick reaction time time settings for the power save mode wheel turning speed etc If you wish to change the drive properties of your wheelchair contact the wheelchair deliverer or manufacturer RE USE AND RECYCLING Wheelchair is suitable and intended for re use For re use wheelchair is serviced completely In the wheelchair there are several different adjustment possibilities For new user the necessary changes and adjustments are done to the wheelchair for example to the seat to the arm and footrests and to the control system All the parts that are removed or replaced should be recycled in proper way There are own recycling points for metal metal parts plastic fenders covers rubber tyres arm rests bushings hazardous waste gas springs gel batteries Other components for example driving motors actuators electric components seats should be deliver to the distributor or the manufacturer and they will take care of the recycling R NET www chasswheel com 32 rev 1 2014 05 08 7 WHEELCHAIR STORAGE Protect the wheelchair from heat and moisture during storage The wheelchair goes into the smaller space by folding the back rest the arm rests and the foot rest Disconnect the batteries and store them fully recharged in a dry and cool place During the storage the batteries should be recharged at least once every six months 8 USE OF THE WHEELCHAIR AS A
11. 542 in the transport vehicle Always use the safety belt installed in the transport vehicle e Safety belts must be in contact with the user s body They must not be held at a distance from the user s body using parts of the wheelchair such as armrests or wheels e Safety belts must be pulled as tightly as possible without causing the user discomfort e Safety belts must not be positioned while twisted R NET www chasswheel com 34 rev 1 2014 05 08 E e Ensure that the third seatbelt anchorage point is not fixed directly to the vehicle floor but to one of the vehicle uprights e A headrest must be installed The headrest optionally supplied for this mobility device by Chasswheel is perfectly suitable for use during transport e The headrest must be adjusted to the user s ear height Seat belts may not be held at a distance The pelvic belt should be positioned in the area from the user s body using parts of the between the user s pelvis and thighs so that it is wheelchair such as armrests or wheels unobstructed and not too loose The ideal angle of the pelvic belt to the horizontal is between 45 and 75 The maximum permissible angle is between 30 and 75 The angle should never be less than 30 The safety belt installed in the transporting vehicle ia should be applied as shown in the illustration at right o EI 1 Centre line of the body 2 Centre of the sternum _ a R NET www chasswheel com 35
12. SEAT IN A VEHICLE In order to use a wheelchair as a motor vehicle seat it needs to be equipped with attachment points to enable anchoring in the motor vehicle These accessories may be included in the standard scope of wheelchair order but may also be obtained from Chasswheel as an option This power wheelchair complies with the requirements of ISO 7176 19 2001 and may be used as a vehicle seat in connection with an anchoring system that has been checked and approved in accordance with ISO 10542 The wheelchair has undergone a crash test in which it was anchored in the transporting vehicle s direction of travel Other configurations were not tested The crash test dummy was secured using pelvic and upper body safety belts Both types of safety belt should be used in order to minimize the risk of injuries to head or upper body It is imperative that the wheelchair is inspected by an authorized dealer before being used again after being involved in a crash Alterations to the wheelchair anchoring points may not be carried out without the manufacturer s permission Caution There is a danger of injury if the wheelchair ts not properly secured during use as a vehicle seat e If possible the user should always leave the wheelchair to use a vehicle seat and the safety belts provided with the vehicle e The wheelchair should always be anchored facing in the transport vehicle s intended direction of travel e The wheelchair must always be secured in a
13. USE eege 11 2 2 BACK REST HEAD SUPPORT ARM REST AND FOOT REST ADJUSTMENTS cccccsaeeesaeeeeaees 17 BACK REST ADJUSTMENT uu ec ccccccccccsssssscesceccesesesssssssssececessessseseesseeceseseessseeeseeeseeegs 17 MANUALLY ADJUSTABLE BACK H EE 17 ELECTRICALLY ADJUSTABLE BACK REST vetcescaseserssecqccteseacesssnocosa aursneaesussacctetessucemustesctaesbeersusdie 17 HEAD SUPPORT ADJUSTMENT ooo iiccccccsccccccccesesessssesssscccseseesssssssseceseseessseeseeseeeeeegs 18 OG MR oe PAI CR 1 8 cctaseescoha tees A EE E S 18 ADJUSTMENT OF A MANUALLY ADJUSTABLE FOOT REST 20 ADJUSTMENT OF AN ELECTRICALLY ADJUSTABLE FOOT REST WITH LENGHT CONPEN SATION BEE 20 2 3 OTHER DEVICES AND SUPPLIES swisientivactenrscctveadvcerieatiwaraentieabiwnriacltratiwasicnriealtertavetinaldontients 21 SPAT BELT USE eera re E E E E EA E 21 Nd DE 21 BIR LI 21 DATTERY RECHARGIN E 21 FS AEE E E AE T EE E EEA cs O A NE E E EEE eee 22 ENRKIAKOIIERlelEaidielS See TIR 23 MOUNTING TO AND FROM THE WHEELCHAIR cccceccesesssesseseceesssssssseeeeeeeeeeeens 23 Rate Le 24 BALANCE ADJUSTMENT EE 25 CLIMBING STEPS EN 26 FREE V elen LIN oen ale tine a nina aa ett wa hacen ieee ett eee ween aeaeerea el 2 5 TRANSPORTATION AND PACKAGING OF THE WHEELCHAIR cccccccececssaeeesaeeevansuvensaeeneanenranes 2 6 WHEELCHAIR SERVICING ccccccccceccecececaeceeaucaecucaecnvaueueancaeuuvaeeuvaneaeeneaeeuvaneaeaneasunvaneuvansaranrass 28 RUBRIK cs Kl e gt ae 28 WEEKLY INSPECTIONS er
14. air Do not over tighten the screws WEEKLY INSPECTIONS Brake tests are made on an even floor with at least one meter of free space around the wheelchair Switch on the control system Check that the light bar is lit in one second or flashes slowly Push the joystick slowly forwards until you hear the parking brakes working The wheelchair may start moving Release the joystick immediately and you should be able to hear the sound of the brakes R NET www chasswheel com 28 rev 1 2014 05 08 E operating in a few seconds Repeat this test three times also by pushing the joystick backwards and to the left and right Check the operation of the lights turn indicators and the balance adjustment If the wheelchair has an electrically adjustable back and or foot rest also check their operation In problem situations do not use the wheelchair but contact service CLEANING AND DISINFECTION THE WHEELCHAIR Clean the wheelchair with a moist soft fabric and diluted cleaning fluid Avoid the use of undiluted cleaning fluids as these may damage the plastic and fabric parts of the wheelchair Follow the recommendations set by the cleaning fluid manufacturers regarding the different materials In the event of the control module becoming dirty it must be cleaned immediately Pressure cleaning or use of a shower is forbidden as the wheelchair has electric units which will be damage when wet The wheelchair can be disinfected totally for example by spr
15. air has four wheel drive and steering Mastering the driving technique requires practice Avoid places where a loss of wheel grip can be dangerous for example wet sloping lawns The wheelchair has a balance adjustment system for improving driving safety and the overcoming of obstacles It is necessary to learn its correct use Always check before driving that the seat is in the correct position Look at the section Balance adjustment Instability can arise when driving on slope if the balance is adjusted incorrectly Adjusting the balance on a sloped surface requires special caution The hill climbing capacity of the wheelchair is greater than the maximum safe driving declination Driving on a steeper ground than a slope of 10 which is equivalent to a climb of one meter over five meters may be dangerous Also level differences greater than 100mm can be dangerous see the pictures below Always use low driving speed and avoid extreme steering movements when driving on a slope or uneven surface 10 cm 10 cm Driving in water is forbidden due to the danger of damaging the wheelchairs electric parts Always use lights in the twilight and dark in order to see any obstacles and dangers in your driving path It is also important that the other road users can see you Releasing the joystick stops the chair In emergency situations the wheelchair can also be stopped by switching off the driving controller EE R NET www chasswheel com 7
16. are mentioned below However the more demanding service operations such as electrical malfunctions driving motors actuators frame parts seat parts foot and arm rests changing the tyres and other technical problems can only be done by a qualified technician in order to maintain the warranty The manufacturer intends the wheelchair to be serviced maintenanced by qualified technician either distributor service agent or the manufacturer at least once a year Service card of the wheelchair is in the last pages of the Owner s manual Please take care of that the Owner s manual goes with the wheelchair to the service When it is a time to service the wheelchair please contact to your FOUR X distributor Following routine operations the manufacturer intends the user to be responsible daily inspections weekly inspections Cleaning the wheelchair If necessary the user could ask assistant or some other person for help DAILY INSPECTIONS Before beginning the drive check the general condition of the wheelchair visually When the driving controller is switched off check that the joystick is not bent or damaged and that it returns to the middle when released Check that all the connectors are in place and undamaged and the cables are in good condition Check that the thin protective rubber around the steering stick is not damaged Handle the protective rubber with care Make sure that the control module is well attached to the wheel ch
17. aying the disinfectant on the wheelchair The electronics of the wheelchair are in the battery box so keep the battery box closed during the disinfection While disinfecting notice the wheelchair s texture surfaces seat supports which should be disinfected with the suitable methods Following operations the user is able to do with help of assistant or some other person measuring the tyre air pressure changing tyres disconnecting the batteries installing the batteries changing the lamp MEASURING THE TYRE AIR PRESSURE The suitable air pressure in the tyre is approx 1 5 bar Air pressure decrease under 1 2 bar and filling over 3 0 bar is not advised This increases the wear of tyres decreases grip and causes extra friction which shortens the driving distance R NET www chasswheel com 29 rev 1 2014 05 08 TYRE EXCHANGE The rim is attached to the motors hub with five coach screws tool size 6mm Support the axle so that the tyre is off the ground After that release the air pressure from the tyre When and only when you have done this open the screws and take of the tyre Both halves of the rim are attached to each other with screws which you are not allowed to open until you have released the air pressure Assembling the wheel with tyre Install inner tube into the outer tyre and install this packet onto the rim half Attach both rim halves together with screws Pay attention that the inner tube does not squeeze
18. ccordance with the wheelchair and anchoring system manufacturers operating manual e Always remove and secure any accessory parts fixed to the wheelchair such as chin controls or tables e If your wheelchair is equipped with an angle adjustable backrest then it must be placed in an upright position e Fully lower elevated leg rests if fitted e Fully lower the seat lifter if fitted e Always completely lower height adjustable leg rests if fitted WARNING Danger of injury exists if a power wheelchair that is not equipped with leak proof batteries ts transported in a vehicle R NET www chasswheel com 33 rev 1 2014 05 08 ES e Only ever use leak proof batteries CAUTION There ts danger of injury if the batteries are not properly secured e Secure the battery belt with the safety How the wheelchair is anchored in a vehicle for use as a vehicle seat The power wheelchair is fitted with four anchoring points which are labeled with the symbol shown on the right Snap hooks or belt loops can be used for fixation e Secure the wheelchair at the front 1 and at the rear 2 with the anchoring system belts Rear only left hand side visible in picture How the user is secured within the wheelchair CAUTION There is a danger of injury if the user is not properly secured within the wheelchair e Even if the wheelchair is fitted with a postural belt this is no substitute for a proper safety belt which complies with ISO 10
19. danger damaging of the wheelchair structure when using features and safety of the wheelchair weaken Risks mentioned above can be prevent by installing the assistant control system into the wheelchair when controlling and driving of the wheelchair are happening by assistant and then user is not able to use the control system of the wheelchair SAFE DRIVING Do not use the wheelchair if you suspect that the use would not be safe For safety take notice of the wheelchairs condition function and noises environmental conditions and the users ability to control the wheelchair Check the wheelchair s condition weekly at the very least The wheelchair has moving parts such as the wheels rods and joints Take note of the dangers your wheelchair i may cause especially in the presence of children and pets Attention Risk of trapping finger R NET www chasswheel com 6 rev 1 2014 05 08 EH Make sure they remain at a safe distance from the wheelchair The places that are especially dangerous are marked with these symbols Avoid loose clothing or jewellery which can become entangled in the moving parts If you are aware of a fault in the driving controller or any other critical part do not drive the wheelchair but deliver it immediately for service Brake releases must be returned to the DRIVE position D after pushing or towing Using the chair on sloped surfaces can be dangerous if the brakes are released The wheelch
20. elt The use of this is always recommended whilst sitting in the wheelchair and must absolutely be used whilst using the Seat Riser System The safety belt must always be adjusted as suitable for the user SEAT OPERATION ADJUSTMENT The wheelchair seat is adjusted by pressing the MODE button whereupon the picture of the adjustment appears on the screen The seat part which is seen darkened in the picture is at that moment adjusting Adjustment happens by moving the guidance stick forwards and backwards Choosing the different parts of the seat occurs by moving the guidance stick to the right and left sides by quick movements By pressing the MODE button again you can get back to the drive situation FOOT SUPPORT ADJUSTMENT The angle of the foot support is adjusted by selecting the foot support adjustment from the MODE selection of the drive control The operational state is chosen when the foot support on the display is visibly darkened The foot support is adjusted by moving the guidance stick forwards and backwards The centre of gravity can be adjusted when the seat part and the horizontal arrow are visibility darkened The centre of gravity adjustment is used for driving in the sitting position up and downhill and as an aid during the Stand Support System When the seat is rised with seat riser operation you are not able to adjust the gravity point backwards RAISING THE SEAT SECTIONS The height of the seat can be adjusted whe
21. ests Joystick module Direction Te indicator E Head lights with indicators Rear lights Leg support 5 S WI BC A Reflectors Tie down brackets with ISO 7176 19 Brake release 2 1 DRIVING CONTROLLER USE The driving controller consists of a joystick and control panel Under the driving controller you ll find the charger socket and the data transfer cable which is connected to the control unit Joystick The speed and direction of the wheelchair is adjusted by the joystick The further you push the stick from the central position the greater the drive speed Releasing the joystick stops the wheelchair and applies the parking brakes The joystick is also used for adjusting extra operations Joystick with a standard knob is suitable for most users There are different alternatives to this knob or the knob can be tailor made Do not replace the knob with self made parts as they may cause dangerous situations eee eee ee R NET www chasswheel com 11 rev 1 2014 05 08 Communication Cable JOYSTICK MODULE Charger Socket Control panel The control panel contains push buttons and an LCD display Operation of the push buttons is defined later in this chapter When the driving controller unit is switched on the LCD display is illuminated in the background and an icon of the currently used function is displayed The symbols displayed are defined la
22. foot rest down and raise your feet on the rest front of the wheelchair To transfer from the wheelchair operate all actions reverse To make transfer easier use for example sliding board on the seat and under the user and slide the user of the wheelchair R NET www chasswheel com 23 rev 1 2014 05 08 DRIVE PRACTICE Familiarize yourself with the wheelchair s performance capacity gradually and on different terrains such as sand snow ice off road paths etc to find the correct adjustments speeds and ways of steering for different situations Drive practice is also necessary for learning safe and flexible use of the wheelchair in different driving situations It is especially important to learn the correct use of the balance adjustment system Start practicing at a low maximum speed when it is easier to control the wheelchair As the wheelchair has four motors and four wheel steering its capacity is great and therefore utmost caution should be applied in the beginning The speed and direction of the wheelchair is adjusted by the joystick By pushing the joystick forwards or backwards the wheelchair moves to the direction determined by the current wheel position If the wheels are turned so that the right side wheels are close to each other picture 2 the wheelchair will move forward to the right when the joystick is pushed forward Picture 3A and backwards to the right by pulling the joystick backwards Picture 3b The driving d
23. he charger plug into the driving controller s charger socket During recharging the battery charge level is shown as an icon on the display and the wheelchair will not be possible to drive Batteries must be recharged immediately if the icon indicating the battery charge level shows only two full pillars Follow the instructions supplied with the charger Use only the charger that has been supplied with the wheelchair Using incorrect chargers could damage the batteries wheelchair or the charger itself R NET www chasswheel com 21 rev 1 2014 05 08 FUSES The wheelchair s main fuse 80A is situated between the batteries If it is blown the wheelchair will not have any electrical functions The user must not change this fuse themselves the wheelchair must be taken for service KOE ADO AKN ENT EN A Ae um men VENTS egaumr ap IN NOT AUER LU Kate t aar Ke a ag j a a arm DL Le Zeil A aniar wia CT WW e ut nun Recess gens frererf zen R NET www chasswheel com 22 rev 1 2014 05 08 3 DRIVING THE WHEELCHAIR MOUNTING TO AND FROM THE WHEELCHAIR To make the mounting easier the foot rest and arm rests can be lifted up as shown in the pictures below Make sure not to damage the controller module and its cable EI 1 Folding the foot rest up 2 Lift the arm rest up 3 Get your legs in front of the wheelchair 3 4 Be seated on the 5 Adjust the angle of wheelchair the footrest Let the
24. he frame ELECTRICALLY POWERED WHEELCHAIR Class C Manufacturer Type CW 3 FOUR X DL Weight 130 kg CHASSWHEEL OY Max mass of the user 125 kg Myllyharjuntie 6 71800 SIILINJARVI LU CC FINLAND Frame no Year Month ELECTRIC WH EELCHAIR Wheelchair classification For outdoor use Maximum safe slope 10 CLASS C USED ON STEEPER SLOPES THAN Obstacle negotiation ability 100mm 10 NS OR GREATER LEVEL Wu D DIFFERENCES THAN 100 mm CAN General driving restriction CAUSE SAFETY RISKS Situated on the battery casing rear case Battery connecting diagram situated inside the battery casing cover CAUTION SEE OWNER S MANUAL FOR INFORMATION FUSEF1 Main fuse value information Situated inside of the main fuse box Using other than gel batteries is forbidden warning USING OTHER THAN Situated on the top of the battery cover rear case GEL BATTERIES IS FORBIDDEN R NET www chasswheel com 9 rev 1 2014 05 08 Freewheeling sing D breaks locked the wheelchair can be driven N breaks released the wheelchair can be towed Situated in every fender Attention read the user manual Situated on the supporting frame both sides from the seat Do not push the wheelchair from the back rest Risk of trapping hand finger These labels are situated in the points where the danger exists R NET www chasswheel com 10 rev 1 2014 05 08 2 EQUIPMENT AND THEIR USE Batteries with main fuse Arm r
25. iately pulled out TI The wheelchair is now locked and the display clearly shows a lock icon To unlock first switch the current on Driving is however still not possible Insert the locking key into the charger socket and immediately pull out It is now possible to drive the wheelchair Troubleshooting If the control system detects an error a flashing exclamation mark appears on the display together with a notice with the code of the possible fault Refer to section electric malfunctions R NET www chasswheel com 16 rev 1 2014 05 08 2 2 BACK REST HEAD SUPPORT ARM REST AND FOOT REST ADJUSTMENTS While making the adjustments beware the possible flattening hazards To get the best adjustment result use the help of the attendant or service person BACK REST ADJUSTMENT The wheelchair seat s back rest can be manually or electrically adjustable While adjusting the back rest assure that there will not be anything between the back rest and the battery casing cover nor the back rest does not pressed against the battery casing cover Back rest adjustment MANUALLY ADJUSTABLE BACK REST The back rest is manually adjusted either by pulling the lever on the side of the back rest while reclining the seat or by turning the wheel on the side of the backrest until the desired position is found ELECTRICALLY ADJUSTABLE BACK REST An electrically adjustable back rest is adjusted with the driving controller The adjustmen
26. ing the MODE button again you can get back to the drive situation FOOT SUPPORT ADJUSTMENT The angle of the foot support is adjusted by selecting the foot support adjustment from the MODE selection of the drive control The operational state is chosen when the foot support on the display is visibly darkened The foot support is adjusted by moving the guidance stick forwards and backwards R NET www chasswheel com 45 rev 1 2014 05 08 FOCUS OF GRAVITY ADJUSTMENT The centre of gravity can be adjusted when the seat part and the horizontal arrow are visibility darkened The centre of gravity adjustment is used for driving in the sitting position up and downhill and as an aid during the Stand Support System The height of the seat can be adjusted when the seat section and the vertical arrow are visibly darkened Adjustment of the seat height is good to use as an aid in adjusting the centre of gravity When the centre of gravity is adjusted possibly back the seat is raised higher ADJUSTMENT OF THE BACK SECTIONS The position of the backs can be adjusted when the backs and the horizontal arrow are visibly darkened a FOLDING OF THE UPPER SECTION OF THE BACK The back part is possible to be folded when the backs upper part is folded backwards through different operations Adjustment of the upper part of the back is possible when the backs and the vertical arrow are visibly darkened a STAND SUPPORT SYSTEM When a
27. irection is corrected by moving the joystick sideways After this keep pushing the joystick straight forward and make only small sideways movements until the correct drive direction is found Avoid extreme movements and start driving slowly to find the correct feel If the wheelchair moves in an undesired way release the joystick This stops the wheelchair in all situations In emergency situations switch the driving controller off When you have learned how to use the wheelchair on a level surface you can start practicing how to negotiate obstacles and hills where it is essential to master the balance adjustment system R NET www chasswheel com 24 rev 1 2014 05 08 BALANCE ADJUSTMENT The balance adjustment system means that the seat can be moved in relation to the frame In addition when the seat is moved backwards it starts to tilt at a certain stage For adjusting the balance the driving controller must be set to the balance adjustment mode This mode is accessed by pressing the MODE button until the display shows the seat parts back rest and seat plate darkened The balance is adjusted by moving the joystick forwards and backwards When the joystick is pushed forwards the seat moves forward in relation to the frame In the drive position for even ground the seat starts to tilt backwards while the balance is shifted backwards The recommended balance positions for driving uphill on even ground and downhill are represented in the pict
28. ll the seat parts are visibly darkened the seat is raised to the users sitting position when the control stick is pushed forwards K If one of the spindle motors which is required for the Stand Support System is broken this operation cannot be used R NET www chasswheel com 46 rev 1 2014 05 08 3 TECHNICAL INFORMATION ON THE STAND SUPPORT SYSTEM Greatest safety use gradient Seat spindle motor Back s spindle motor Foot rest motor SaVer seat standard width effective seat depth backrest height back angle seat surface height at the front edge seat plane angle 5 Linak LA 31 D Reac RE 25 Reac RE 25 490 mm min 500 mm min 510 mm min 12 52 550 mm 22 37 R NET rev 1 www chasswheel com 2014 05 08 47 Pr SEAT RISER FOUR SEAT RISER SYSTEM R NET www chasswheel com 48 rev 1 2014 05 08 Contents 1 SAFETY RECOMMENDATIONS Safe driving 2 EQUIPMENT AND THEIR USE Safety belt use Seat functions adjustment Electric adjustment length compensation for the foot support Centre of gravity adjustment Raising of the seat section Backrest adjustment 3 TECHNICAL INFORMATION ON THE SEAT RISER SYSTEM R NET www chasswheel com 49 rev 1 2014 05 08 1 SAFETY RECOMMENDATIONS THIS USER MANUAL IS FOR USE ONLY TOGETHER WITH THE OWNERS HANDBOOK THIS SECTION EXPLAINS ONLY CONNECTED MATTERS CONCERNING USE OF THE SET RISER SYSTEM SAFE DRIVING Do not use the Sea
29. n the seat section and the vertical arrow are visibly darkened R NET www chasswheel com 51 rev 1 2014 05 08 ADJUSTMENT OF THE BACK SECTIONS The position of the backs can be adjusted when the backs and the horizontal arrow are visibly darkened When the seat is rised with seat riser operation you are not able to adjust the back rest backwards 3 TECHNICAL INFORMATION ON THE SEAT RISER SYSTEM Greatest safety use gradient 5 Seat rising motor Linak LA 31 D Back s spindle motor Reac RE 25 R NET www chasswheel com 52 rev 1 2014 05 08
30. ne a ship a train or other means of transport contact the organiser of transportation to receive transport instructions 1 2 If the wheelchair needs to be packed drive the wheelchair on the pallet Notice that the user cannot be in the wheelchair while driving it on the pallet Wheelchair should be attached to the pallet like it is attached for the transportation see pictures 1 and 2 Footrest should be bent down and foot plate up Head support is good to be adjusted in the lowest position If necessary the head suppoert can be removed and attach on the seat Back rest can be bent forwards by pulling the lever on the R NET www chasswheel com 27 rev 1 2014 05 08 EE side of the back rest see page 17 part Manually adjustable back rest If wanted the wheelchair can be covered for example wooden frame or cardboard box The wheelchair can be moved for example to truck by driving it or if the wheelchair is on the pallet by loading pump 6 WHEELCHAIR SERVICING After driving under moisture circumstances take care of drying the wheelchair for example by storing it in a warm space Do not leave the wheelchair outside or in cold and moisture spaces Not following these instructions might damage the wheelchair By servicing the wheelchair regularly you ensure the functioning and safety of your wheelchair A well serviced wheelchair is a long term aid Part of the servicing can be performed by users themselves these operations
31. on the display the driving controller must be restarted Fault When the system detects a fault the Fault icon appears on the display Refer to section Electric malfunctions Motor temperature This icon appears on the display when the system has automatically reduced power input to the motors to prevent overheating Control system temperature This icon is shown on the display when the control system decreases power to protect itself from overheating Timer This icon is shown when the control system is changing from one operation mode to another The sand glass represents the time lapsing R NET www chasswheel com 15 rev 1 2014 05 08 Balance and seat adjustment The wheelchair s balance and seat can be adjusted by pressing the MODE button whereupon this icon will be seen on the display The seat part that is highlighted in the icon is currently adjustable Adjustment is carried out by moving the joystick forwards and backwards Different parts of the seat are chosen by moving the joystick to the left and right SO Temporarily displayed icons In so far as the temporary icons are programmed to be seen the icons below will be temporarily displayed by pressing the Speed or Profile buttons al e AA The Wheelchair can be locked using the locking key To lock the wheelchair the driving controller has to be switched on The locking key is inserted into the charger socket and immed
32. oor premises APPLICABILITY FOR DIFFERENT TYPE OF USERS Wheelchair is intended for person who has active life with the family Wheelchair is also suitable for persons who want to move and act independently both in the city and in the countryside The wheelchair is intended for users weighing not more than 125kg and having the ability to learn the correct use of the equipment and the physical preconditions for using the controlling system and the necessary equipment Wheelchair is perfectly suitable for persons whose injury disease demands soft drive and stability of the seat there is special flexible chassis structure in the wheelchair Wheelchair is suitable for instance for accident patients multiple sclerosis patients brain infarct patients overweight persons and arthropathy patients Wheelchair is not suitable for visually disabled blind person badly spastic person whose moves are so uncontrollable that controlling the wheelchair is impossible disabled person who is not able to understand the correct function of the wheelchair or he doesn t have the physical preconditions for using the wheelchair person whose weight cross the maximum user weight These features which limit the wheelchair use can be a risk both to the wheelchair user and to the person around and to the other environment Risks can be among others losing the control of the wheelchair falling down crashing when the wheelchair user and persons nearby are exposed to
33. r cables create a safety risk Check the condition of the tyres regularly It is important for the steering properties and grip abilities to have a correct tyre pressure Measuring the tyre pressure is explained in section Wheelchair servicing Use the locking key to prevent illicit use of the wheelchair Someone other than the owner using the wheelchair is a safety risk Always attach the wheelchair to the car s body part during transport Sitting in the wheelchair during transportation is absolutely forbidden without the use of the correct 3 point seatbelt attached fitted in the vehicle Unauthorized repairs and modifications are forbidden The user may perform the servicing operations referred to in section wheelchair servicing When the wheelchair is being serviced or adjusted the driving controller must be switched off Using the other than gel batteries is forbidden due to the danger of damaging the wheelchair s electric parts Handling tools in close proximity to the batteries may cause short circuit Handling an open flame is forbidden because of the danger of major serious damage The battery casing is not intended to be used as a storage container The cables in the battery naves should not disconnect on one s own In the problem situation please contact the service R NET www chasswheel com 8 rev 1 2014 05 08 THE PERMANENT LABELLING OF THE WHEELCHAIR Identification plates situated on the left side of t
34. r fasteners are located below the covering In front lights screws are located on top of the covering Detach the lens Change lightbulb driving light 0 7W blinker 0 6W FRONT LIGHTS AND REAR LIGHTS Maintenance free LED light DIRECTION INDICATORS Maintenance free LED indicator The user can get suitable lamps for Four X wheelchair from the Four X distributor Chasswheel s part number AO2LED Front light LED or front light with bulb AO3LED Rear light LED or rear light with bulb SPARE PART INFORMATION The manufacturer intends that the user can change the lamps and the batteries by himself if he wants and is able to do it Here is the spare part information for user from the lamps and the batteries e Suitable lamps for Four X wheelchair the user can get from the Four X distributor Chasswheel s part number Driving light LED or driving light bulb e Suitable gel batteries for Four X wheelchair the user can get from the Four X distributor Chasswheel part number Gel battery 73Ah Other wheelchair spare parts the manufacturer intends the Four X distributor or manufacturer to change NOT USER If there are some parts to be changed the user should contact immediately to the Four X distributor Please find your distributor information from the cover page of Owner s manual or manufacturer s webpage www Chasswheel com R NET www chasswheel com 31 rev 1 2014 05 08 ELECTRIC MALFUNCTION The d
35. rev 1 2014 05 08 9 TECHNICAL INFORMATION CW3 FOUR X DL Wheelchair classification Maximum allowable user weight Driving speed Driving distance depending on drive conditions Minimum ground clearance Obstacle negotiation ability Maximum obstacle negotiation ability Slope climbing capacity Maximum safe slope Turning radius Turn around width Operating temperature Charger standard Maximum permitted charging current Total weight of the wheelchair Maximum weight of dismountable parts Seat Recaro standard width effective seat depth backrest height back angle seat surface height at the front edge seat plane angle Overall dimensions of the wheelchair width length height varies depending on the seat Tyres both rear and front tyres Tyre pressure depending on the model Light equipment driving lights rear lights direction indicators Electric system Main fuse Driving controller Driving motors 4 x 250 W Brakes Standard battery MK Gel Battery 73 Ah Spindle motor balance adjustment Frame Shock absorption C 125 kg 10 km h approx 40 km 130 mm 130 mm 130 mm 20 10 1150 mm 1700 mm 25 C 40 C SA 12 A 149 kg 3 8 kg 450 mm 522 mm 682 mm min 12 52 570 mm 22 37 686 mm 1250 mm 820 890 mm 3 00 8 1 5 3 0 bar 150 kPa 300 kPa 12V 2x3 W 24 V 12 V 24V 80A R Net system PG Driving Technology 1000W 4 pcs
36. rire E E T E E ES 28 CLEANING AND DISINFECTION THE WHEELCHAIR ooo ceececccccessssseeeseeseeseeeeeeens 29 MEASURING THE TYRE AIR PRESSURE secidccccscessscse sedate dancusvesdceunindsduentenedenciedavenvaieasedsteameusiess 29 TYRE e TC E 20 DISCONNECTING THE BATTERIES ssccoscesccieccte actions seb yecatenciaassavecenctucteenecvtganstaneteescbvevsccendteeneaness 30 INSTALLING THE HA EE 30 CFANGING THE CAMPS EE 31 SPARE PART INFORMA TION E 31 ELECTRIC MALFUNCTION ME 32 BGS IO Mt TE 32 RE USE AND RECYCLING oui eeccccccccccccsssesssscsssecccsssessssssssscccsssesssseessseceseseessseesesseseseees 32 7 N HEEECHAIR KEE 33 8 USE OF THE WHEELCHAIR AS A SEAT IN A VEHICLE ccccsscececesaeceeaeeevaneavensaesnvaneavaneaneneass 33 9 TECHNICAL INFORMATION CW3 FOUR X DL ccccccccseceeesaeeevcuceecusaeenvaeeuvaneaeanvanenvaneavansananrass 36 10 SERVICE CARD OF FOUR X DL WHEELCHAIR ccccccceceececeeeecueaeeneaeenvaueueaneaeenvaneuvaneavansanneass 37 ss R NET www chasswheel com 5 rev 1 2014 05 08 1 SAFETY RECOMMENDATIONS Read this manual carefully before using the wheelchair It will guide you on flexible and safe use of the wheelchair and advise you on the procedures for problem situations Please contact the supplier if you have any further questions The wheelchair is intended for outdoor use where it can cross obstacles in normal outdoor conditions and drive on uneven ground The wheelchair can also be used in suitable ind
37. riving controller indicates electric malfunctions by flashing an exclamation mark on the display For safety reasons driving with the wheelchair is prevented during the malfunction Typical electric malfunctions are caused by the connectors or the batteries The most typical reasons for malfunctions are listed below The driving controller has switched on to the power save mode This happens automatically when the driving controller has not been used for a period of time The time depends on the programming of the driving controller To re start switch the driving controller on and off The batteries are weak when battery charge level icon flashes slowly Batteries should be recharged as soon as possible The batteries are recharging Check that the charger plug is not connected to the drive control The connectors of the driving controller system or the battery have become loose Switch the driving controller off and check that all connectors are in place The brake releases are on Turn the brake releases in towards the chair Instructions can be found in section Freewheeling Switch the driving controller on and try to drive the wheelchair If the exclamation mark continues to flash on the display switch the driving controller off Do not use the wheelchair and contact service PROGRAMMING The driving properties of the wheelchair can be reprogrammed In delivery the wheelchair s driving properties are set so that they are
38. s _ No Additional maintenance if needed Notices if needed Maintenance done by Date and place R NET www chasswheel com 40 rev 1 2014 05 08 T Frame no Annual maintenance Yes No Additional maintenance if needed Notices if needed Maintenance done by Date and place Annual maintenance Yes _ No Additional maintenance if needed Notices if needed Maintenance done by Date and place LE R NET www chasswheel com 41 rev 1 2014 05 08 STAND SUPPORT SYSTEM www chasswheel com 2014 05 08 Contents 1 SAFETY RECOMMENDATIONS Safe driving 2 EQUIPMENT AND THEIR USE Safety belt use Knee support use Electric adjustment length compensation for the foot support Centre of gravity adjustment Raising of the seat section Folding of the upper part of the back Head support adjustment Lift operation 180 tilting Operation of the upright position raiser 3 TECHNICAL INFORMATION ON THE STAND SUPPORT SYSTEM R NET www chasswheel com 43 rev 1 2014 05 08 1 SAFETY RECOMMENDATIONS THIS USER MANUAL IS FOR USE ONLY TOGETHER WITH THE OWNERS HANDBOOK THIS SECTION EXPLAINS ONLY CONNECTED MATTERS CONCERNING USE OF THE STAND SUPPORT SYSTEM SAFE DRIVING Do not use the Stand Support System if you suspect that its use is not safe For safety of use the condition of the appliance environmental conditions and the user s ability to control the machine
39. sible the brake releases must be switched on This can be done by turning the levers 4 pcs in both axles towards the outside of the wheelchair When the parking brakes are released the wheelchair cannot be driven and therefore controlling it is difficult and moving it on a sloping surface is dangerous During the towing the driving controller must be switched off When freewheeling notice that it is forbidden to push the wheelchair 5 TRANSPORTATION AND PACKAGING OF THE WHEELCHAIR Transferring the wheelchair into the vehicle must be done with ramps or hoister that is located in vehicle Behind the wheelchair s seat there are attachment rings on the fastening pipes for the arm rests picture 1 to which attachment straps can be fastened during transportation When strapping the wheelchair care must be taken that the wheelchair s electric cabling is not damaged During transportation it must be assured that the brakes are not released and the control module is well protected Sitting on the wheelchair during transportation is definitely forbidden Always use the car s own seat during transport Additional equipment includes wheelchair bars that can be connected to the both axle pipes picture 2 These wheelchair bars can be connected to a car s chassis at four points It is also possible to attach a rope to the bars so the wheelchair can be towed in the case of electric malfunction etc For transporting the wheelchair on an aeropla
40. speed in the outdoor driving profile Left turn indicator switch By pushing the button the wheelchair s left turn indicator lights are switched on The indicator lights are switched off by pressing the push button again When the indicator lights are on the LED next to the push button will flash Right turn indicator switch By pushing the button the wheelchairs right turn indicator lights are switched on The indicator lights are switched off by pressing the push button again When the indicator lights are on the LED next to the push button will flash Hazard warning switch By pressing this push button all the wheelchair s indicators will switch on Pressing the push button again will switch the indicators off When the warning indicators are on the LEDs next to the push buttons for warning and direction indicators will flash Lights switch The drive lights are switched on and off When the drive lights are switched on the LED next to the push button will illuminate R NET rev 1 www chasswheel com 13 2014 05 08 Charger socket The charger socket is situated beneath the control unit The socket is used for recharging the wheelchair s batteries or to lock the wheelchair Only connecting the proper charger plug or lock key is permitted Charger Plug single Pin to bottom LCD DISPLAY The state of the driving controller can be observed using the icons shown on the display The icons shown and used on the display
41. t Riser System if you suspect that its use is not safe For safety of use the condition of the appliance environmental conditions and the user s ability to control the machine must be observed On an inclined surface driving in the erect position is absolutely forbidden due to the dangers of overturning Do not use the appliance if you suspect that some part may be broken but deliver the appliance directly for servicing Before raising the lift ensure that the safety accessories are properly attached The appliance is installed with a speed limiter which limits the maximum speed automatically when the seat riser operation is used If you suspect that the limiter is not operating properly do not use the Seat Riser System but contact service When inclining the back backwards in the sitting position take care that the back rest does not create pressure on the battery compartment This can cause the seat s spindle motor or battery compartment to be damaged When using the Seat Rises System ensure that the foot support can move freely In a case that the foot support catches on the floor an obstacle or an axis stop operations and adjust the various sections of the seat until the foot support is freed Do not push the wheelchair Use the drawstrings for transferring the wheelchair R NET www chasswheel com 50 rev 1 2014 05 08 2 EQUIPMENT AND THEIR USE SAFETY BELT USE The Seat Riser System is equipped with a safety b
42. t mode is chosen by first pressing the MODE button and then moving the joystick to the left or right until the seat icon on the display only highlights the back rest section The back rest is then adjusted by moving the joystick forwards and backwards By pressing the MODE button you can return to the drive mode R NET www chasswheel com 17 rev 1 2014 05 08 HEAD SUPPORT ADJUSTMENT In order to adjust the height of the head rest the plastic butterfly nut 1 at the back of the head rest needs to be loosened until the head rest can move freely on its attachment Once the desired height has been achieved the butterfly nut has to be tightened up again The height of the head rest can be adjusted smoothly In order to adjust the depth of the head rest the plastic butterfly nut 2 behind the rod needs to be loosened until the head rest can move freely on its attachment Once the desired position has been achieved the butterfly nut has to be tightened up again The depth of the head rest can be adjusted smoothly The padding of the head rest is attached to the rod by a globe joint 3 The padding can be easily changed according to the user s head position ARM REST ADJUSTMENT The width of the arm rest is adjusted by loosening the screw 1 and moving the arm rest sideways When the Suitable position has been found retighten the screw The maximum width is 60mm picture below The arm rest angle is adjusted by loosening the
43. ter in this chapter ON OFF button With the ON OFF button the driving controller can be switched on and off Do not use this switch to stop the wheelchair except in an emergency Horn button A sound signal sounds when the push button is pressed Speed buttons Decrease Increase The maximum speed of the wheelchair can be increased by pressing the right push button and decreased by using the left push button The choice of maximum speed is seen on the display whilst choosing provided it is programmed to be displayed The maximum speed is the lowest when there is only one darkened column on the display and the greatest when all the columns on the display are darkened When the joystick is moved forwards or T m 4 rev 1 www chasswheel com 12 2014 05 08 backwards the driving controller transfers to driving mode and applies the selected maximum speed The maximum speed can also be adjusted while driving MODE button With the MODE button you can navigate the adjustment menu The available menus depend on the programming and the available operations of connected optional equipment Profile button The desired user profile can be chosen with the profile button The available profiles depend on the driving controller s programming and its equipment The driving controller has pre programmed profiles for indoor and outdoor driving The maximum speed for the indoor driving profile has been adjusted lower than the
44. ures below Uphill Even ground Downhill Seat moved front Balance in the middle Seat moved back normal position and tilted K i X og Leg Avoid driving uphill if the seat is moved backwards Do not drive downhill if the seat is moved forwards These positions are incorrect and can be dangerous Adjust the maximum speed lower when driving up or downhill and when crossing high obstacles In case of a fault in the balance adjustment actuator in its connecting cable or in the joystick module the seat is left in the position in which it is when the fault occurs This may lead to a situation in which the user has to drive with an incorrect balance adjustment which in turn may lead to fall of the wheelchair R NET www chasswheel com 25 rev 1 2014 05 08 CLIMBING STEPS Approach the step slightly sideways so that the wheelchair is able to mount the step one wheel at a time Move the balance position backwards and raise the foot rest so that it doesn t hit the step Drive the wheelchair s front wheels onto the step Move the balance forwards so that wheelchair s rear part becomes lighter and drive the entire wheelchair onto the step Finally move the balance to even ground position The same driving method can be used to overcome greater obstacles 4 R NET www chasswheel com 26 rev 1 2014 05 08 4 FREEWHEELING Malfunctions transport etc may demand that the wheelchair should be towed To make this pos
45. y to the mechanical foot rest The foot rest angle is adjusted by choosing foot rest adjustment on the driving controller s MODE menu The operational mode is chosen when the displayed foot rest is highlighted The foot rest is adjusted by moving the joystick forwards and backwards R NET www chasswheel com 20 rev 1 2014 05 08 2 3 OTHER DEVICES AND SUPPLIES SEAT BELT USE The wheelchair is equipped with a safety belt Its use is recommended If the safety belt is not used it Should be prevented from dangling and_ getting entangled to the wheels TYRES All the tyres of the wheelchair are the same and because of their tread pattern they have a good grip on different surfaces The tyre pressure should be checked regularly Measuring the tyre pressure is defined in section wheelchair servicing BATTERIES Service free gel batteries are used as the wheelchair s standard batteries Using other than gel batteries is forbidden due to a risk of electronic damage The batteries are situated in a case behind the back rest which can be opened by turning the screw located at the centre of the lid Instructions for removing and installing the batteries are in section wheelchair servicing Take note of the Safety instructions regarding the batteries in section safety recommendations Used batteries should deliver to the proper recycle places BATTERY RECHARGING The wheelchair batteries are recharged by connecting t
Download Pdf Manuals
Related Search