PIR Manual - William Stump & Associates, LTD.
Contents
1. diameter fresnel head field of view is approximately 10 degrees Vibration Sensor When using the vibration sensor to monitor a dump site best results are achieved when attaching the head to a stick and placing it in the dump pile If monitoring a gate the sensor can be mounted to a post When the gate is opened or tampered with the motion will send a signal to begin recording While monitoring a road attach a high strength fishing line 5Olb braided wire recommended Secure the fishing line at high tension 1 above ground Any object passing the line will activate recording 5 Now you are ready to test it with the Guardian 2000 Place your Guardian 2000 into PGM mode Test the PIR sensor again and the Guardian 2000 will activate and begin re cording Figure 3 Vibration Sensor 1 Obtain the hand held control module provided with your Guardian 2000 and turn it on with the alarm feature acti vated Maintain a close distance in order to hear the audi ble alarm 2 The vibration head contains two magnets that can be used to attach to a metal surface The head can also be secured with the two mounting screw holes 3 Connect the four pin head to the housing The sensor will be ready for immediate use 4 Conduct a test of the vibration sensor by walking near the head The vibration sensor will transmit an alarm signal to the handheld control module 5 Now you are ready to test it with the Guardian 2000 Place your Gua2. held control module provided with your Guardian 2000 and turn it on with the alarm feature acti vated Maintain a close distance in order to hear the audi ble alarm Secure the PIR head to a solid surface pointing towards your activation area To detect horizontal movement en sure that the back of the head has the cut outs on the left and right sides with the slots straight up and down See Figure 3 Connect the four pin head to the housing The sensor will Stabilize after 1 minute Conduct a test of the PIR by walking or by placing your hand in front of the lens The PIR sensor will transmit an alarm signal to the handheld control module
3. RODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF THE MANUFACTURER IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL THE MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER William Stump amp Associates Ltd Guardian 2000 PIR and Vibration Sensor User s Manual G2K PIR and Vibration Sensor See what you ve been missing INTRODUCTION Congratulations and thank you for purchasing the Guardian 2000 PIR and Vibration Sensor This sensor automatically integrates with your existing Guardian 2000 video system and is manufactured using stringent standards from customer input Features include e Weatherproof housings e Dual Infrared pyroelectric sensor e AA battery operation e Indoor and outdoor operation e Upto 100 ft range depending on sensitivity setting and ambient temperature As you read through this manual please keep in mind your system has been rigorously inspected for utm
4. The limited warranty stated herein is subject to all of the following terms and conditions TERMS AND CONDITIONS 1 NOTIFICATION OF CLAIMS WARRANTY SERVICE If Purchaser believes that the product is defective in material or workmanship then written notice with an explanation of the claim shall be given promptly by Purchaser to the Manufacturer but all claims for warranty service must be made within the warranty period No repair or replacement of any product or part thereof shall extend the warranty period as to the entire product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and the Manufacture s sole obligation is to supply all labor necessary to repair any product found to be defective within the warranty period Purchaser s failure to make a claim as provided in paragraph 1 above or continued use of the product shall constitute an unqualified acceptance of such product and a waiver by Purchaser of all claims thereto 3 EXCEPTIONS TO LIMITED WARRANTY The Manufacturer shall have no liability or obligation to Purchaser with respect to any product requiring service during the warranty period which is subjected to any of the following abuse improper use negligence accident modification failure of th
5. e end user to follow the operating procedures outlined in the user s manual failure of the end user to follow the maintenance procedures in the service manual for the product attempted repair by non qualified personnel operation of the product outside of the published environmental and electrical parameters or if security seal has been defaced altered or removed The Manufacturer also excludes from warranty coverage products located outside the United States and consumable items such as fuses and batteries Items not manufactured by Backgrounds Unlimited Inc but included in system bought by Purchaser are limited to original manufacturer s warranty and will be repaired by Backgrounds Unlimited Inc on cost of material basis 4 PROOF OF PURCHASE The purchaser s dated invoice must be retained as evidence of the date of purchase and to establish warranty eligibility DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES THE MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY AND OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE AND OR ANY OTHER COMPARABLE STATE STATUE THE MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON MANUFACTURER S P
6. ost quality assurance prior to shipment About the PIR Sensor The PIR Sensor incorporates a pyroelectric sensor and a radio frequency transmitter to activate your Guardian 2000 The result is an extremely reliable sensor designed to significantly reduce false activations Being able to bury the transmitter housing makes this an almost truly invisible sensor The flexible head also makes it extremely easy to deploy under almost any condition Testing the Sensors Testing the sensor during deployment is crucial for Success Once the initial setup has been made test the sensor be fore leaving the target area Conduct several walk through tests in the target area to de termine proper sensor placement Deployment PIR Sensor When using the PIR sensor to monitor a trail best results are achieved when placing the head about waist level The PIR sensor should be solidly mounted to avoid exces sive movement Therefore it is equipped with a small black clamp on the head to assist attaching to a solid object Other devices such as wire ties zip ties hook and loop type fasteners and even natural vines can be used The PIR sensor has two sensing elements arranged to can cel out false alarms from vibration temperature changes and sunlight The sensor also has an added filter window which is most sensitive to human body radiation detecting movement up to 100 ft depending on sensitivity settings With the long range 1 1 4
7. rdian 2000 into PGM mode Test the PIR sensor again and the Guardian 2000 will activate and begin re cording Table of Contents General Pre Operation Setup Testing Deployment Warranty Information General The PIR Sensor uses infrared radiation detection for operation When an object such as a person animal or vehicle passes in front of the sensing head a transmitter sends a signal to the Guardian 2000 record unit for activation The PIR sensor comes standard with a long range head containing a fresnel lens which allows for the maximum detection range up to 100 ft de pending on sensitivity settings See Figure 1 The weatherproof housing and flexible head enable quick and effortless installa tions Pits 1 2 ON A HORIZONTAL PLANE HEAT SOURCE MOVEMENT OUTPUT SIGNAL Figure 1 Pre Operation PIR and Vibration Sensor 1 2 3 Connect the antenna to the top of the housing Remove 4 screws from the lid of the transmitter housing Set the sensitivity by turning the knob The far left allows for the least sensitive while the far right is a maximum set ting Only PIR Sensor See Figure 2 Insert 4 AA alkaline batteries into the transmitter s bat tery holder To turn power off simply remove the batteries from the battery holder Sensitivity Adjustment Left Least Sensitive Right Most Sensitive Figure 2 Setup PIR Sensor 1 Obtain the hand
Download Pdf Manuals
Related Search