GPS Vehicle Tracker User Manual VT810
Contents
1. 711 134xxxxxxxx 0000 The format of setting one preset number e g 2 711 134XxXxXxXXXxXx 158XXXXXXXX L50XXXXXxXxx 0000 The format of setting three preset numbers Single location query a message about the latitude and longitude will be 6660000 0000 Is the factory set user returned password which can be changed 9880000 0000 Is the factory set user Single location query a message about the specific location will be returned password which can be changed Monitoring function The guardian uses a mobile phone to send the message instruction 5550000 0000 is the user password to the vehicle tracker Upon receipt of the instruction the vehicle tracker dials the number of the mobile phone which has sent the message instruction After the call is connected the vehicle 5550000 0000 Is the factory set user tracker enters the monitoring mode password which can be changed Note The monitoring function can be used only when a preset number and the center number are set For the center number setting and the preset number setting please refer to the 710 and 711 instruction setting formats described in the I nstruction Set respectively Time setting instruction 56 7 year month day hour minute second user password 4 digits e g 56 110513 125820 0000 Through sending this instruction the user can change the one key time announcement 730 sampling interval 0 or 15 65535 seconds nu2. if the password is wrong amp 803 amp Password Error amp amp will be returned e g 803 203 171 233 248430000 0000 or it can also be set through the domain name e g 8034 www xxx com 30000 0000 Set the electronic fence e g 51 500 5 22 5442N 113 91E 0000 or 151 500 5 22 54425 113 91W 0000 After successful setting amp 751 amp CONFIG OK amp amp will be returned to the phone When the terminal leaves the area the fence alarm message will be sent to the center number Description N refers to north latitude S refers to south latitude E refers to east longitude and W refers west longitude N S E W is the necessary condition of the instruction Read the electronic fence Send the instruction 752 4 digit user password to the terminal After the instruction is successfully sent the terminal reads the work status data of the fence and returns it to the phone If the password Is wrong amp 752 amp PASSWORD ER amp amp will be returned e g 52 0000 The following will be returned open 1 lat 22 543685N Ing 113 910633E distance 500 time 5 status 2 Or open 1 lat 22 543685S lng 113 910633W distance 500 time 5 status 2 Wherein open 1 refers to the activation of the fence open 0 refers to the deactivation of the fence lat 22 543685N refers to north latitude 22 543685S refers to south latitude Ing 113 910633E refers to east longitude 113 910633W refers to wes
3. 0 05m s Speaker A Insert SIM card with beveled corner inward Note e The SIM card shall be GSM card e Make sure to keep enough money in the SIM card account e Make sure the SMS service of the SIM card have been subscribed for To use the real time tracking by service platform and positioning by SMS the user has to subscribe for the GPRS service 4 Wiring precautions Power supply ACC relay 4 PIN 1 The standard power supply of the equipment is 9V 58V DC Please use the factory supplied power cord the red wire is the positive wire and the black wire is the negative wire When connecting the negative wire please ground it separately and do not connect it to other ground wires 2 ACC wire green is used to connect to the vehicle ACC switch Be sure to connect the ACC wire because the vehicle tracker will decide whether to enter the security status depending on the ACC switch status if the ACC wire is not connected the vehicle will be kept in the security or sleep status Under the status of security or sleep if vehicle vibration occurs the vibration alarm will be triggered If anti theft alarm function is not required you can connect the ACC wire with the positive wire in parallel to maintain high electrical level 5 Description of special functions 1 Security function If the ACC wire is connected to the ACC switch this equipment will start the security function automatically in five minutes after the vehi
4. GPS Vehicle Tracker User Manual VT810 1 Please read this manual carefully for correct operation 2 You need to ask a professional to install this product in a safe position of your vehicle Avoid dangerous or unsuitable positions otherwise harm to the driver or passengers may occur 3 This manual is just for your reference The contents and operating steps described in this manual may be different from that of the actual product please refer to the actual product 1 Overview This vehicle tracker is a remote vehicle positioning device consisting of a GPS module and a GSM GPRS module which is featured by compact size good concealment and high precision It can provide the GPS satellite positioning information and can also provide the positioning information supported by the GSM base station if the GPS satellite information Is unavailable and the information about the latitude and longitude coordinates can be sent to the system platform and the preset mobile phone number You can make use of these features to locate and manage your vehicle 2 Definition LAR Download cable EA MIC SOS u Power cable Relay ACC Turn on off button USB i nector Card slot Indicator 3 Operating environment aE e Less than 80MA On Standby Wegh D GPS capability Hot start lt 1 5s Warm start lt 34s Cold start lt 35s Autonomous Position Accuracy 3 0 m 2D RMS DGPS 2 5 m Velocity Accuracy 0 1m s DGPS
5. al positioning Blue indicator Ea refers to the GSM GPRS signal status Flash evey 10 seconds Normal connection to the server for data uploading Flash evey 4 seconds GSM normal standby status Flash evey 1 second No GSM signal initialization call in progress incoming call 7 Query by SMS Send the message 9880000 to the terminal using a mobile phone and then the terminal will return a message about the location information with Google map link click the link by cell phone then the detailed position will show on Google map directly 8 Description of Accessories 1 Power cord Relay Yellow Negative wire Black TA pin Connection to vehicle ACC switch Green Positive wire Red 2 SOS button 3 Microphone 4 Relay fh Instruction list Instruction Description Set the center number Set the center number through the message sent by a mobile phone After successful setting the terminal returns amp 710 amp Config OK amp amp 710 center number user HH password e g 710 134xxxxxxxx 0000 Description The SOS alarm and low battery alarm messages will be returned to the number Set a preset number Use a mobile phone to send the setting instruction to the terminal After successful setting the mobile phone will receive the message amp 711 amp CONFIG 711 phone number 1 phone OK amp amp returned by the terminal number 2 phone number 3 user password e g 1
6. cle engine is turned off If vehicle vibration occurs within one minute the equipment will enter the security status with 1 minute delay and will enter the security status unless no vehicle vibration occurs 2 Sleep mode After entering the security status if no vehicle vibration occurs within 20 minutes this equipment enters the sleep mode In the sleep mode this equipment neither locates nor uploads data but can send receive messages and make answer calls so as to achieve maximum energy saving 3 Vibration alarm Under the security status including the sleep status if vehicle vibration occurs this equipment immediately disconnects the relay and dials the mobile phone number of the vehicle owner to give an alarm meanwhile it wakes up the GPS positioning and uploads the alarm and location data to the service platform 4 Wire cutting alarm Under the security status when the main power line of the vehicle tracker is disconnected the vehicle tracker will send the wire cutting alarm message to the mobile phone number preset to receive the SOS message and uses the inner backup battery instead The backup battery can work 7 10 hours If the positive wire and negative wire of equipment are connected together after power line had been cut the equipment still works normally 6 Definition of indicators Red indicator mm refers to the GPS status Flash at intervals of 1 second No GPS signal Flash at intervals of 4 seconds GPS norm
7. mber of pieces of data uploaded 0 10 user password 770 new password 4 digits old password 4 digits 801 letters or numbers 0 20 digits user password 802 APN letters or numbers 0 32 digits login user name letters or numbers 0 20 digits login password letters or numbers 0 20 digits user password Set the timed data uploading function The factory set uploading interval of the product is 30 and under this circumstance the timed uploading function is turned on The user can change the parameter according to his needs e g 730 20 4 0000 Description 20 refers to point sampling every 20 seconds and the positioning information will be uploaded after point sampling 4 times that is the uploading interval is 20 4 80 seconds The user can change the parameter according to his needs Note The user can send the instruction 730 0 1 0000 to turn off the GPRS so as to enter the power saving mode Change the user password Description After the instruction is executed the terminal will change the user password according to the user s requirements After successful setting amp 7TO amp CONFIG OK amp amp will be returned to the phone if the password Is wrong amp 770 amp PASSWORD ER amp amp will be returned e g 770 1111 0000 After the instruction is executed the user password changes from 0000 to 1111 Change the user name Description After the instruction is e
8. rm message IMEI number Out of the fence Latitude amp An alarm message indicating the vehicle is out of longitude information the fence After the vehicle tracker enters the sleep mode the power of the ACC wire is disconnected When vehicle vibration occurs the vehicle Vibration alarm tracker will send the vibration alarm message to the mobile phone number preset to receive the SOS message When the main power line of the vehicle tracker is disconnected the vehicle tracker will send the Wire cutting message wire cutting alarm message to the mobile phone number preset to receive the SOS message Precautions This equipment is of non waterproof design so please prepare a waterproof bag This equipment shall be supported by the GSM network Make sure to keep enough money in the SIM card account so as to avoid inconvenience This equipment can not work under power off status or outside the service area even you are a registered user This equipment supports GPS and GSM GPRS dual positioning mode and the results of both shall be deemed equivalent Please use this equipment within the scope permitted by law Any consequence arising from violation of the laws shall be solely borne by the user
9. t longitude distance 500 refers to the radius of the fence time 5 refers to the sampling interval Status 2 refers to that the terminal gets valid satellite data and the fence works normally Status 1 refers to that the fence is activated but the terminal fails to get valid satellite data status 0 refers to that the electronic fence is not set 760 user password 223 user password 233 user password 901 902 904 905 920 Cancel the electronic fence Turn on the fuel power cut off function Turn off the fuel power cut off function Read the user parameters After the instruction is sent the terminal returns the following message center number password user name user password preset number 1 preset number 2 preset number 3 preset number 4 IMEI number e g 134XxXxXxXxXxxx 0000 13900139000 0000 134xxxXxxxxx 356823032080204 Read the GPRS parameters mode sampling tine number of samples APN APN user name APN password P port version number e g 5 0 0 CMNET 121 9 206 148 30000 2011 09 02 18 36 810_V1 XX GPRS connection GPRS disconnection Voice switching instruction After the instruction is sent the terminal can switch between English and Chinese Short Message Description IMEI number SOS Latitude amp longitude information or base station information SOS message IMEI number Terminal battery is low please charge in time Low battery ala
10. xecuted the user name of the terminal under the GPRS mode will be set according to the requirements After successful setting amp 801 amp CONFIG OK amp amp will be returned to the phone if the password is wrong amp 801 amp PASSWORD ER amp amp will be returned e g 801 13900139000 0000 Set the APN Description After the instruction is executed the terminal APN under the GPRS mode will be set according to the requirements After successful setting amp 802 amp CONFIG OK amp amp will be returned to the phone if the password is wrong amp 802 amp PASSWORD ER amp amp will be returned e g 1 802 CMNET 0000 After the instruction is executed the terminal APN is CMNET the login user name and password are blank e g 2 802 CCDLEN Guest Guest 0000 After the instruction is executed the APN is CCDLEN the login user name is Guest and the login password is Guest Note The default APN of this product is CMNET 803 fixed IP address port number user password 751 fence radius meter sampling interval minute latitude longitude user password 752 user password Set the service address This instruction is used to set the GPRS center server address The server address can either be a fixed IP whose format IS xxx xXXX XXX XXX Or a domain name whose length is less than 64 bytes After successful setting amp 803 amp Config OK amp amp will be returned to the phone
Download Pdf Manuals
Related Search