SVANMOBILE Manual
Contents
1. Reference Value dB 76 6 of the cursor selected by the cursor Pinch close in the vertical direction to zoom out the spectrum plot Pinch open in the vertical direction to zoom in the spectrum plot Thin blue vertical line Measured spectrum the cursor Reference spectrum Press somewhere in the plot area to set the position of the cursor Swipe the screen up or down to change the displayed range of the spectrum 2013 SVANTEK Fig 3 4 The Spectrum display mode In case of FFT data it is also possible to zoom in or out the displayed range of frequencies It can be done by pinching open or close in the horizontal direction see Fig 3 5 SVANTEK 11 SvanMobile User Manual Cursor kHz 8 6 Value dB 48 4 Pinch open in the horizontal direction to zoom in the frequency axis KHz 1 1 kHz 9 6 kHz 18 1 Hz Fig 3 5a An exemplary FFT spectrum Cursor kHz 8 6 Value dB 46 8 Pinch close in the horizontal direction to zoom out the PA frequency axis kHz 4 9 kHz 9 1 kHz 13 4 Hz Fig 3 5b The same FFT spectrum with a greater zoom In case of 1 1 octave and 1 3 octave spectra a reference spectrum may be shown together with the measured spectrum lt has to be loaded from a csv file stored on the Android device specified in the Options panel for details on the format of this file refer to the Appendix Different files should be loaded for audio and full 1 1 octave and 1 32. a SVAN instrument to communicate with Measurement Contains the results of the current measurement displayed in a similar way as in the connected SVAN instrument Markers Enables one to remotely set the markers in the connected SVAN instrument CG Measurement Enables one to enclose various forms of comments with the Tracking measurement results x Measurement Enables one to view and edit created Measurement Tracking Viewer Tracking records Gol Files Enables one to browse and download files from the SVAN instruments memory fb Setup Editor Enables one to remotely configure the measurement setup xX of the SVAN instrument Options Enables one to configure various options of the SvanMobile application SVANTEK 4 SvanMobile User Manual More details on how to use each of these panels can be found in subsequent chapters of this manual Note The Measurement Markers Measurement Tracking and Files panels are not available unless the Android device is connected to a SVAN instrument The remaining three buttons at the bottom of the menu see Fig 1 4 enable one to remotely start stop and pause the measurement performed by the connected SVAN instrument H H Fig 1 4 Buttons for remote pausing starting and stopping the measurement SVANTEK 5 SvanMobile User Manual 2 CONNECTING WITH SVAN INSTRUMENTS SvanMobile provides two methods for connection between an Android device and a SVAN instru
3. by long pressing its name on the list and selecting Disconnect from the pull down menu Note In some versions of Android it may be necessary to manually pair the Android device with the SVAN instrument before attempting to establish connection in SvanMobile In order to pair the devices you have to do the following Inthe Android device s settings go to Wireless amp Networks Bluetooth Press Search for devices On the list of available devices press the name of your SVAN instrument Enter the authorisation code By default the code is 1234 it can be set in the meter Menu gt Instrument gt Bluetooth gt Authorisation Code The devices will be paired and you will be able to see the SVAN instrument on the list in the Connection panel 2 2 CONNECTION USING INTERNET A SVAN instrument can be connected to the Internet using a GSM modem or via Wi Fi using a MOXA modem You can then establish an Internet connection between the SVAN instrument and an Android device with SvanMobile To do so you first need to manually add your device to the list by doing the following 1 Go to Options using the menu at the top of the screen see Chapter 1 4 Overview of the application 2 Press Add TCP connection by IP address or Add TCP connection by unit number see Fig 2 2 depending on how you wish to access your SVAN instrument e if using the IP address you have to specify the address and port at which the ins
4. in the Measurement panel If you uncheck one of the modes it will disappear from the menu available in the Measurement panel and will be omitted when swiping the screen Start measurement stop measurement pause measurement if this option is set as on the Start Stop Pause buttons will be displayed not only in the menu at the top of the screen but also at the bottom of the Measurement panel in the 1 Prof amp 3 Prof display mode SVANTEK 22 SvanMobile User Manual Screen orientation this option can be used for changing the orientation of the screen The orientation does not automatically change while using the SvanMobile application independent of the current Android device settings The landscape horizontal orientation is particularly useful when the Android device is connected to an external projector Path to working folder allows to specify the location for storing on the Android device files downloaded from SVAN instruments and other files used by the SvanMobile application Automatic Tracking if set to Single the Automatic Tracking related comments will be enclosed to the measurement results only once when the Start Stop button is pressed if set to Periodic the comments will be enclosed each time a Result file is created Reference files for spectrum allows to select files from the Android device s memory that will be used for displaying reference spectra in the Measur
5. you can open a pull down menu which allows to edit upload or delete the selected setup file Once a setup file is opened the Setup Editor displays a list of settings available for the connected SVAN instrument The settings are identical to those available in the instrument s menu for details please refer to the manual of the particular instrument To access the Save Save as Upload and Activate and Exit commands press the Menu button Setup editor 5 SVANTEK Function Pressa category name on this list to edit settings in Display the selected category or to access its subcategories Measurement File Instrument Auxillary Setup Report Use this command to upload the currently edited setup file to the connected SVAN instrument in order to remotely modify its settings Use this command to navigate back to the list of stored setup files Fig 6 3 Editing a setup file in the Setup Editor The settings are grouped in a hierarchical structure While browsing the settings available in a setup file you can go one step up in the settings hierarchy by pressing the Back gt button To navigate back to the list of stored setup files use the Exit command as shown in Fig 6 3 The edited setup file can be saved with the same filename using the Save command or as a copy with different filename using the Save as command You can upload a setup file to the conn
6. It is only possible online so this panel cannot be opened unless the connection with a SVAN instrument is established Note The marker related features in SvanMobile depend on the SVAN instruments capabilities There may be limitations compared to what is described in this chapter according to what is available in the connected SVAN instrument At the top of the panel the measurement results are displayed You can change the displayed function and profile in the same way as in the Measurement panel viz by touching the function name profile number in order to switch to the subsequent available function or profile or only in case of functions by long pressing the function name in order to select from a list of all available functions Markers 5 SVANTEK Int time 00 00 01 Press to switch to function to the subsequent subsequent profile available function or long press to open the list of available functions A started Block marker 2 Event You can enter the marker s CAR name here Press to set the end time Activate Press to set the start of Marker 1 l i time of Marker 2 4 Block Press to set the position Activate of the Point marker 3 2013 SVANTEK ER Fig 4 1 The Markers panel The markers are set in SvanMobile in a similar way as in the meter You can switch the type Event Point Event point or Block of each marker by clicking the blue label next to the marker s number You can specify the na
7. S Comments created as described in the previous section can be viewed and edited using the Measurement Tracking Viewer or MT Viewer To access the Measurement Tracking Viewer use the icon in the menu at the top of the screen As this tool only uses svmt files stored on the Android device it can be opened when working offline i e without any SVAN instrument being connected The numbers at the bottom of the screen indicate the number of the currently displayed record and the total number of records stored in the currently viewed svmt file You can SVANTEK 17 SvanMobile User Manual switch between the available records by pressing the buttons The data displayed in the Measurement Tracking Viewer panel will change according to the selected record The text fields and the four comment editing buttons can be used in the same way as when adding comments using the Measurement Tracking tool for details see the previous section The locations marked on the map indicate the location data specified in subsequent records stored in the currently viewed svmt file The currently displayed record is marked in red while others in green By touching the location markers you can also switch between the records Measurement tracking viewer een Wines Location data in different records red current green other Unit Time 2013 01 01 05 50 37 Project Notes You can use these tools in the same way as in t
8. adding comments in the Measurement Tracking panel Icon after Icon Type of comment comment added Audio file recorded using the Android device s oo d microphone E emm z Ta A photo taken by the Android device s camera a thumbnail D of the photo TS A video clip recorded using the Android device s camera a thumbnail of the video clip Weather information acquired automatically using the PR Android device s weather services or typed manually in a dialog box Automatic tracking You can use the Automatic tracking tool to automatically add records containing the time location and weather data in one of the following modes Single a record is added every time the measurement is started or stopped Periodic a record is added every time the meter starts integrating new measurement results according to its Integration period parameter To turn on the automatic tracking press the gt button located at the bottom of the screen The saving mode single periodic can be selected in the Options panel Storing records in files Several records can be stored in a single svmt file and then viewed together see next section You can select the file for storing the current record by pressing the tn button Then after pressing the la button the the new record containing all the created comments will be stored in the selected file 5 2 VIEWING AND EDITING COMMENT
9. and available after pressing the Menu button see Fig 6 1 Files list 5 SVANTEK R1 2013 07 04 15 59 10 R2 2013 07 04 15 59 20 R3 2013 07 04 15 59 30 Press a file name from this cosa sie ia listto download a file from d i EE the SVAN instrument to the R6 2013 07 04 16 00 00 indici dia R7 2013 07 04 16 00 08 O7JANO 2012 01 07 01 35 14 O7JANI 2012 01 07 02 11 06 07JAN2 2012 01 07 02 31 24 07JAN3 2012 01 07 02 43 24 O7JAN4 2012 01 07 02 44 00 O7JAN5 2012 01 07 02 59 24 O7JAN6 2012 01 07 04 30 08 O7JAN7 2012 01 07 04 48 02 O7JAN8 2012 01 07 22 04 30 07JAN9 2012 01 07 23 45 14 Swipe the screen up or 08JANO 2013 09 24 11 19 38 down to see the whole list O8JANT 2013 09 24 12 19 42 Use this command to refresh 2 BIANI 2013 09 24 12 36 42 the list of files stored on 08JAN3 2013 09 24 12 47 46 the SVAN instrument Fig 6 1 The Files panel The Menu button may be located differently in various Android devices The downloaded files are stored in the SvanMobile working folder which can be specified in the Options panel SVANTEK 19 SvanMobile User Manual 6 2 USING THE SETUP EDITOR A set of parameters values related to various functions of a SVAN instrument such as e g measurement profiles or file saving options can be stored in the memory of an Android device in the form of a svt file called hereafter a setup file The Setup Editor enables one to acquire modifiy and transfer these files in order to
10. de in the Measurement panel The Menu button may be located differently in various Android devices SVANTEK 9 SvanMobile User Manual 3 1 1 PROF amp 3 PROF The 1 Prof amp 3 Prof display mode allows for displaying the results of measurement of one selected function profile in large format and the results of measurement of three other functions profiles in smaller format below You can switch between the functions available for displaying by pressing the name of currently displayed function the same applies to profiles By long pressing the name of the currently displayed function you can also open a menu to select from all the available functions see Fig 3 2 D 1 Prof amp 3 Prof v CH SVANTEK Long press function name to select from a list of available functions 66 0 dB P 3 55 dB P 1 43 0 dB P 1 Press the name of a function or a profile number to switch to the next function or profile 2013 SVANTEK Fig 3 2 Selecting the displayed functions in the 1 Prof amp 3 Prof display mode If the results are displayed on red background it means that they are out of the range of the meter Fig 3 3 The way results out of range are displayed in the 1 Prof amp 3 Prof display mode 3 2 METER TABLE The Meter table display mode allows for displaying the results of measurement of several functions simultaneously in the form of a table The displayed functions and profiles can be selected in t
11. displaying the results of measurement obtained by a SVAN instrument on the screen of a mobile Android device This can be done using the Measurement panel which can be accessed by pressing the EB icon in the menu at the top of the screen The measurement results are displayed in the Measurement panel in a similar way as in the connected SVAN instrument The panel can be used in five different so called display modes 1 Prof amp 3 Prof Instrument status Meter Table Spectrum Table Spectrum each of which allows to view different data acquired from the connected instrument They correspond to the meter s display modes of the same names except Instrument status which allows to display general information about the connected instrument To switch between the display modes you can swipe the screen to the left or right or use the menu accessed through the Menu button see Fig 3 1 You can also disable some of the display modes in the Options panel in this case only the selected display modes will be available in the menu and by swiping the screen VR WNP 1 Prof amp 3 Prof 4 SVANTEK Int time 00 00 01 Swipe the screen to the left or right to switch between a A 2 2 d R subsequent display modes 66 0 dB P 3 55 dB P 1 43 0 dB P 1 Use this menu to switch to a selected display mode Press the Menu button to open the diplay modes menu Fig 3 1 Changing the display mo
12. ected SVAN instrument in two ways When editing a setup file use the Upload and Activate command see Fig 6 3 When displaying the list of setup files stored on the Android device long press the name of a setup files and in the pull down menu select Upload and Activate The uploaded setup file is automatically activated meaning that the SVAN instrument s settings are modified according to the ones specified in the uploaded file SVANTEK 21 SvanMobile User Manual 7 OPTIONS This chapter contains a description of all the options that can be configured using the Options panel These options only concern the SvanMobile application not the connected SVAN instruments You can access these options by pressing the icon in the menu at the top of the screen Options 5 SVANTEK Licensing Display Modes Start measurement stop measurement pause measurement off Screen orientation portrait default Path to working folder mnt sdcard SvanData Automatic Tracking Single Reference files for spectrum Add TCP connection by IP address Add TCP connection by unit number GPS location listener On Channel No only for multichannel instr 4 ver 2 1 2 G 2013 SVANTEK Fig 7 1 The Options panel Licensing allows to activate a purchased license For details see Chapter 1 3 Licensing Display Modes allows to select which modes will be available
13. ement panel in the Spectrum display mode Add TCP connection by IP address by unit number allows to add an Internet connection with a SVAN instrument to the connections list For details see Chapter 2 2 Connection using Internet GPS location listener allows to decide whether GPS will be used by SvanMobile to access your location Note that the GPS location service also needs to be enabled in the Android device s settings Channel No allows to choose the channel of the connected multichannel SVAN instrument from which measurement results are acquired Version number at the bottom of the Options panel the number of the currently installed version of SvanMobile is displayed SVANTEK 23 SvanMobile User Manual APPENDIX SVANMOBILE FILE STRUCTURES A 1 REFERENCE SPECTRUM FILES The spectra used as reference in the Spectrum display mode in the Measurement panel are stored in the form comma separated values CSV files These files can be generated using the SvanPC software in the following way 1 In SvanPC open the file containing data you wish to use as reference spectrum Open the 1 1 Octave or 1 3 Octave view 2 3 Use the File Save Current View command or the IN button in the Toolbar 4 Save the file on your Android device You can then load this file in the Options panel using the Reference files for spectrum button Such CSV file consists of two rows containing the following val
14. ending on the Android version e g Settings gt Personal gt Security gt Unknown sources newer versions or Settings gt Applications gt Unknown sources older versions 3 Find and open the apk file Note If you downloaded the file directly from the Internet to the Android device it can be accessed through the notification on the navigation bar 4 Accept the permissions required by SvanMobile and press Install SVANTEK 2 SvanMobile User Manual 1 3 LICENSING After downloading the SvanMobile application you get a free 30 day license for using it You can purchase the unlimited license from your local Svantek distributor To activate the purchased license follow these instructions 1 Open the SvanMobile application and go to Options 2 Press the Licensing button 3 Press the Send Mail button to open a template of the key request e mail Complete the message by entering your name and phone number and send it The address of the Svantek office is already typed in the template 4 After the key is generated SvanMobile will automatically download it from the Internet and the license will be activated If you cannot or do not want to use Internet connection you can also contact the Svantek office in any other way to achieve the key corresponding to your device s ID number and load it from a file stored on the device by pressing the Load key from file button in the Licensing dialog box Note The ID number
15. he Measurement Tracking panel Use these buttons to change the currently displayed record Fig 5 1 The Measurement Tracking Viewer panel tal lla By pressing the lt button you can open another svmt file By pressing the aly button you can delete the currently displayed record By pressing the RM button you can save changes done in all the records in the currently edited svmt file You can send the currently viewed svmt file using a chosen application by pressing the Send by command in the menu It will let you choose between all the installed applications that allow for sending files such as e g E mail or Skype SVANTEK 18 SvanMobile User Manual 6 EXCHANGING FILES AND SETTINGS SvanMobile makes possible the transfer of files and settings between an Android device and a SVAN instrument 6 1 DOWNLOADING FILES You can view and download files from a connected SVAN instrument using the Files panel which can be accessed by pressing the icon in the menu at the top of the screen Note Downloading files is only possible online so the Files panel cannot be opened unless the connection with a SVAN instrument is established After opening the Files panel a list of files currently stored on the connected SVAN instrument is acquired and displayed To download a file simply press its name on the list In order to refresh the list of files after it has already been acquired you can use the Refresh comm
16. he same way as in the 1 Prof amp 3 Prof display mode viz by pressing their names in order to switch between subsequent available functions and profile numbers or only in case of functions by long pressing their names in order to open a list of all available functions SVANTEK 10 SvanMobile User Manual The User calculator located at the bottom of the Meter table panel enables one to display the differences between chosen measured functions The functions and profiles used for calculation at both sides of the minus sign can be selected in the same way as other displayed functions and profiles see the description above 3 3 SPECTRUM The Spectrum display mode allows for displaying a plot of the spectrum of the measured signal if spectrometric results 1 1 Octave 1 3 Octave or FFT are currently being acquired You can change the displayed range of the spectrum by zooming in or out by pinching the screen open or close or by swiping the screen up or down A cursor can be placed at a selected frequency to display numerical value of the spectrum above the plot The cursor is represented by a thin blue vertical line To place it touch the screen somewhere in the plot area The last three points of the x axis located to the right of the highest frequency correspond to total results Spectrum ap Value of the measured 5 svantek Nu and reference spectrum Current position Cursor Total Z Value dB 50 1 at the frequency
17. me of each marker using the field below the marker s number and type In case of Point and Event point markers the Update button below the name field serves for setting its at the current time In case of Block and Event SVANTEK 14 SvanMobile User Manual markers the Activate Deactivate buttons serve for setting their start end time respectively A started event or block marker is shown on green background Note The name and type of the markers can only be changed when the measurement is stopped The start and end time of the markers can be set only when a logger measurement is currently performed SVANTEK 15 SvanMobile User Manual 5 MEASUREMENT TRACKING The Measurement Tracking tool serves for enclosing additional comments in the form of notes voice recordings photos video clips weather information and location data with the measurement results 5 1 CREATING COMMENTS In order to enclose a comment with the currently performed measurement open the Measurement Tracking panel by pressing the icon in the menu at the top of the screen The Measurement tracking tool can only be used online so this panel cannot be accessed unless the connection with a SVAN instrument is established Comments are grouped in so called records A record is described by the date and time acquired from the connected SVAN instruments real time clock and can contain all the forms of various comments such as e g location data or a pho
18. ment using Bluetooth and using the Internet 2 1 CONNECTION USING BLUETOOTH In order to establish a Bluetooth connection make sure the following settings are configured properly In your Android device check if Bluetooth is on It can usually be found in Settings gt Wireless amp Networks gt Bluetooth Note If you can see the Bluetooth is not available message in the Connection panel this means that Bluetooth has been turned off in your Android device Next set up your SVAN instrument as follows Menu gt Instrument gt Communication Ports gt Bluetooth ON Menu gt Instrument gt Bluetooth gt Visible gt ON Menu gt Instrument gt Bluetooth gt Transfer on stop only OFF If all the above settings are configured as described SvanMobile will scan for the available SVAN instruments and display a list of them in the Connection panel To connect with one of the instruments press its name on the list You can also manually force SvanMobile to scan again by pressing the Refresh button see Fig 2 1 Connection CH SVANTEK Connect to instrument 192 168 168 187 8014 n An instrument available by bluetooth Press to connect long press to display a list of options Press this button to refresh the list of instruments 2013 SVANTEK available by bluetooth Fig 2 1 Connection using Bluetooth SVANTEK 6 SvanMobile User Manual When connected to an instrument you can disconnect it
19. octave spectra The reference spectrum is drawn in brighter color than the measured spectrum Its value is also shown above the plot for the frequency selected by the cursor In order to show or hide the reference spectrum open the menu at the top of the screen and press the Display reference spectrum button Fig 3 6 SVANTEK 12 SvanMobile User Manual D Spectrum va 7 CH SVANTEK Cursor Total Z Value dB 50 1 Reference Value dB 76 6 Go to the Options panel to specify files containing data to be used as reference spectrum Press to show hide the reference spectrum Fig 3 6 Displaying the reference spectrum 3 4 SPECTRUM TABLE The Spectrum table display mode allows for displaying the spectrum of the measured signal if spectrometric results 1 1 Octave or 1 3 Octave are currently being acquired in numerical form The displayed table consists of a column containing frequency values on the left and a column containing spectral data measured at the corresponding frequencies on the right 3 5 INSTRUMENT STATUS The Instrument Status display mode allows for displaying some general information about the connected SVAN instrument SVANTEK 13 SvanMobile User Manual Press to change the displayed 4 USING MARKERS SvanMobile makes it possible to remotely set markers in the connected SVAN instrument using the Markers panel accessible through the Z icon in the menu at the top of the screen
20. ount the variety of Android devices available on the market it is probable that SvanMobile will look somewhat different on your device In particular this concerns the Menu button which in some devices is present as a hardware button and in others as a virtual button on the Navigation bar at the bottom of the screen this refers to Fig 3 1 6 1 and 6 2 The layout of the SvanMobile application may also change significantly when the screen orientation is changed from portrait to landscape However since the functionality of each element of the application remains unchanged regardless of the screen orientation it is not treated in detail in this manual and all the figures are presented as if the screen was in portrait orientation While using the SvanMobile application you can always access helpful information about the currently displayed panel by pressing the Help button at the bottom right corner of the screen see Fig 1 1 To hide the Help window press the Help button once again 5 2013 SVANTEK DI Press this button to access helpful information about the currently displayed panel press it again to hide the Help window Fig 1 1 The bottom bar and the location of the Help button 1 2 INSTALLING SVANMOBILE To install SvanMobile 1 Download the apk file from the Svantek website 2 On your Android device enable the Allow installation of apps from unknown sources option It can be found in different places dep
21. poem gt SvanMobile CN23012 USER MANUAL v 1 0 SvanMobile version 3 1 SVANTEK October 2013 CONTENTS t GETUNOSTARTE RE 2 LD ABOUT TH ET 2 12 Tee E oaeee sE aee E a S O Ee E E E T EE E 2 es ING 3 TA OVERVIEW OF THE APPLICATION cca 3 2 CONNECTING WITH SVAN INSTRUMENTS cccccsccsccsccscccccecsscsscsseeees 6 2 1 CONNECTION USING BLUETOOTH arr 6 22 CONNECTION USING INTERNE E 7 3 DISPLAYING MEASUREMENT RESULTS ssssesesessssssssssssssessossssssssssosseses 9 il e Ee 10 gt Tt iii 10 o PE ON E 11 SERN e gear 13 35 RM a 13 6 USING MARKER sondare palin ieo nea ara sonni 14 3 MEASUREMENT TRACKING seneca alia 16 tee 16 5 2 VIEWING AND EDITING COMMENTS sssseeeeesssssstttsssssssstttttttttttttttttttt tbtt ssnst ttrrrrrrrteeeeeeeetens 17 6 EXCHANGING FILES AND SETTINGS ccccccccccccscceccsccsccsccscsscsscssese 19 C eet e IEN 19 SEH ET EI OR lai ii 20 T OFON sionn 22 APPENDIX SVANMOBILE FILE STRUCTURES csscceccsccccccccecescssceseeees 24 At REGERENCESPECIRUMI FILES cranio ii risa 24 AMI a nia 24 SVANTEK 1 SvanMobile User Manual 1 GETTING STARTED SvanMobile is an application for smartphones and tablets with the Android operating system which extends the functionality of SVAN instruments 1 1 ABOUT THIS MANUAL The figures presented in this manual have been created using one particular Android device Taking into acc
22. ree worldweatheronline com SVANTEK 24 SvanMobile User Manual The content of an exemplary svmt file lt xml version 1 0 encoding utf 8 gt lt MeasurementTrackingRecord unitType 979 unitSubType 0 unitNumber 21004 svanMobile Timestamp svanMobile Timezone 60 unitTimestamp 2013 01 01 05 50 37 unitLatitude unitLongtitude mobileLatitude 52d 11m 40 42s N mobileLongtitude 21d 10m 21 77s E resultFile R1 loggerFile LOG95 commentary photoFile photoSize photoData audioCommentFile audioSize audioData videoClipFile videoSize videoData weatherPressure weatherHumidity weatherT emperature weatherCloudcover weatherWindspeedKmph weatherWinddirDegree weatherCode project svanMobile TimestampOnStart resultFileOnStart loggerFileOnStart unitTimestampOnStart gt lt MeasurementTrackingRecord gt lt MeasurementTrackingRecord Note unitType 979 unitSubType 0 unitNumber 21004 svanMobile Timestamp svanMobile Timezone 60 unitTimestamp 2013 01 01 05 54 36 unitLatitude unitLongtitude mobileLatitude 52d 10m 25 77s N mobileLongtitude 21d 11m 20 48s E resultFile R1 loggerFile LOG95 commentary photoFile photoSize photoData audioCommentFile audioSize audioData videoClipFile videoSize videoData weatherPressure weatherHumidity weatherT emperature weatherCloudcover weatherWindspeedKmph wea
23. remotely set up a connected SVAN instrument Note Unlike the Files panel the Setup Editor works offline which means it can be used without a SVAN instrument being connected to the Android device However connection is obviously necessary for downloading and uploading the setup files After opening the Setup Editor by pressing the A icon in the menu at the top of the screen you can see a list of setup files stored on the Android device if there are any You can download the current setup from a connected SVAN instrument using the Get setting from instrument command available after pressing the Menu button Fig 6 2 If there are no files stored on the Android device and if a connection is established you will be automatically proposed to download the current setup Note The setup files are stored in the SvanMobile working folder which can be specified in the Options panel Setup editor Setup1 svt Setup2 svt List of setup files currently stored on the Android device press a file name to open it for edition Use this command to download the current setup from the connected SVAN instrument Fig 6 2 The main view of the Setup Editor The Menu button may be located differently in various Android devices SVANTEK 20 SvanMobile User Manual Once a setup file is stored on the Android device you can open it for editing To do so simply press a file name on the list Note By long pressing a file name
24. shown in the Licensing dialog box and included in the key request e mail is unique for each Android device It is necessary for obtaining the license This is the ID number unique for your particular Android device Temporary license Please contact vour Svantek distributor for obtaining a key for ID 611abbc320f1bec0 Send Mail Load key from file Use this button if you want to activate the license without using the Internet Use this button to send a key request e mail to the Svantek office Fig 1 2 The Licensing dialog box 1 4 OVERVIEW OF THE APPLICATION The SvanMobile application is composed of 8 different panels You can select the displayed panel using the menu located at the top of the screen see Fig 1 3 To open the menu press the SZ button at the top right corner of the screen or drag down the bar at the top of the screen You can also access this menu when it is hidden by pressing the Back button of your Android device The available panels and their functionalities are described in Table 1 1 SVANTEK 3 SvanMobile User Manual Press this bar to open the menu Select a panel using one of these icons 1 Prof amp 3 Prof 4 svantek Int time 00 00 01 P 2 2013 SVANTEK 2013 SVANTEK Fig 1 3 Using the menu to select a panel to display Table 1 1 Panels available in the SvanMobile application and their functionalities Icon Name Functionality Connection Enables one to select
25. therWinddirDegree weatherCode project svanMobileTimestampOnStart 2013 09 13 15 28 39 resultFileOnStart loggerFileOnStart unitTimestampOnStart gt lt MeasurementTrackingRecord gt It is recommended not to edit the svmt files in other ways than using the Measurement Tracking and Measurement Tracking Viewer tools The svmt files differ from the xm documents in that they do not have a root element and therefore they cannot be viewed using typical XML viewers The structure of the svmt files may change in future releases of SvanMobile SVANTEK SvanMobile User Manual
26. to Timestamps Two timestamps are stored in each record one representing the start time of the measurement result file this is the time displayed on the screen below the map and one representing the time of saving the record In the case when only logger results are acquired the time of activating the Measurement Tracking tool is taken into account instead of the start time of the measurement result file Location data The location data is acquired automatically using the Android device s location services if they are enabled You can also manually point the location on the map after pressing the x icon located at the top right corner of the map Project name and notes You can specify a name for the project and add notes using the text fields located below the map Pressing the X icon will clear the notes field Other forms of comments You can add other forms of comments to the current record using the buttons described in Table 5 1 When a type of comment is added the icon of the button changes indicating that pressing this button again will enable to view the added comment and edit it In case of audio photo and video comments by long pressing the corresponding button you can access a menu allowing to load the content for the comment from a file stored on the Android device or if a comment has already been created to change preview or remove it SVANTEK 16 SvanMobile User Manual Table 5 1 Buttons for
27. trument can be accessed e if using the unit number you have to specify the instrument type e g SVAN 979 its serial number and the AS Address Server password which has to be set up in the SVAN instrument Once the TCP connection has been added you can connect to the instrument by pressing its name on the list in the Connection panel analogously to the connection using Bluetooth Note You can remove a TCP connection from the list by long pressing its name on the list and selecting Remove When connected to an instrument you can disconnect it by long pressing its name on the list and selecting Disconnect from the pull down menu SVANTEK 7 SvanMobile User Manual SVANTEK Options CH SVANTEK Licensing Display Modes Start measurement stop measurement pause measurement off Screen orientation portrait default Path to working folder mnt sdcard SvanData Automatic Tracking Single Reference files for spectrum Add TCP connection by IP address Add TCP connection by unit number Channel No only for multichannel instr 4 ver 2 1 2 2013 SVANTEK Use these buttons to add a particular SVAN instrument to the list of instruments available by Internet using its IP address or its serial number and AS password Fig 2 2 Buttons for adding a TCP connection in the Options panel SvanMobile User Manual 3 DISPLAYING MEASUREMENT RESULTS SvanMobile makes possible
28. ues Frequency Hz lt Frequency values gt lt Ch number gt lt Mode gt lt Filter type gt lt Type of data gt lt Spectral data gt en e g Chl e g SLM e g Z e g 1 3 Octave RMS dB A 2 SVMT FILES The svmt files are used by the Measurement Tracking tool for storing comments grouped in records enclosed to measurement results For details see Chapter 5 Measurement Tracking The svmt files are text documents that use a syntax similar to the XML syntax A svmt file is composed of several XML resembling elements called MeasurementTrackingRecord one such element for each record stored in the file Each MeasurementTrackingRecord element is described by XML resembling attributes in the form of name value pairs that specify the data contained in the record The names of the attributes are self explanatory you can see all the available attributes in the example on the next page The file related data concerning photo and video comments are stored as base64 code i e a single photo file is stored using three attributes lt photoFile gt the name of the file lt photoSize gt the number of bytes after base64 coding lt photoData gt the base64 code of the file s content Video files are stored in an analogous way Attributes related to weather information are the ones beginning with weather They describe various weather parameters according to their names which are by default downloaded from f
Download Pdf Manuals
Related Search