Camera Parking Assist System Camera Parking Assist
Contents
1. Wire connection Sensor installation GND 1 Select a proper surface area which is 45 70cm to the ground as a horizontal guideline o ABCD ALANLA Reversing light YYYY gl Red Pink ACC Orange DC Black GND 3 Divide the distance between 4 Check the size of the hole saw to be o or E EEEE TET sensor A and D into three parts matching the diameter of the sensors Mark the average point for B before drilling any holes Micro tab camera and C sensor Sensor D 6 Install the sensor into the hole and eee mount firmly in the Sensor B ne bumper Sensor C Sensor A l X The sensor shown above may be different from the product 2 Select a smooth surface area along the horizontal guideline and 12 20cm away from the left and right side Mark them for A and D sensors 5 Install the sensor vertically the up sign must be on upside 7 Insert the plug into the socket and turn the sealing screw cap tightly Camera installation ECU installation Flush mount camera installation Insert the camera and press into the hole firmly Connect the red wire to the reversing light wire Micro tab camera installation 1 Choose a proper place 2 Fix one side of the camera above the number plate and with screw drill a hole H al k C 4 Connect the system to the monitor and adjust the camera dire2. Be Be Be Be OSD setting Once ACC is ON one of the default clock 1 Volume and voice adjustment 2 Date amp calendar 5 Turn off the display setting will appear as below DISPLAY OFF Press the MENU and V Press the MENU button CALENDAR Press MENU and then x button to select DISPLAY to enter the OSD menu V button to select ries 18 OFF Press SET to turn r fers 4 CALENDAR icon then off the display Press any Factory default ae 22 press SET button to button to turn on the enter CALENDAR Q W O display 9 y menu to change setting VOLUME VOICE Press or V button to choose Press SET 3 Time settin 09 14 2009 MON ors 18 button to activate the g e hightlighted option Press MENU and then V button to select TIME Q y K icon then press SET button to change the setting VOLUME VOICE Press SET button again to choose the volume 17 00 09 14 2009 VOICE v SUN MON TUE WED THU FRI SAT 4 Display setting 30 1 2 3 4 8 9 10 11 22 24 25 SYSTEM Press MENU and V as button to select SYSTEM Calendar mode VOLUME Press or V button to ws Mm icon then press SET _ q 18 button to change the select the volume 1 low 4 high Q setting Press SET to save and press MENU to return to the previous menu False detection may occur in the following situations After installation please fully test the system before use Heavy rain dirty or dam
3. and engage reverse gear the system will start scanning the rear area If there is any object within the detection range the image digital distances and corresponding parking assist lines will appear on the monitor while the audible sound will change tones when the distance gets shorter voice warning is optional Each piece of our products has passed the most stringent test before releasing to the market It performs well at a wide temperature range and becomes very useful when you are reversing at a raining day snowing day or at night etc With Steelmate s camera parking assist system on board you can enjoy a convenient and nervousfree reversing experience For parking assist system Input voltage Operating current Detection range Display range Operating temperature For rearview camera Video standard Graphic sensor Horizontal resolution Minimum illumination View angle Operating temperature For TFT monitor Size Resolution System Input voltage Working current Operating temperature Beep volume 10 16VDC lt 250mA 0 1 2 5m 0 3 2 5m 40 85 NTSC PAL Color sensor 400 TV lines lt 1 5 Lux 120 135 138 20 80 40 85 2 5 640 H x 240 V NTSC PAL 9 16VDC lt 250mA 20 60 70 90dB The technical specification of the camera may vary It may change according to the camera design Technical specifications About the monitor 1 Rearview on the LCD mo
4. the LCD monitor No obstacle behind the vehicle 1 Check whether sensors are mounted too low or detecting the ground 2 Check whether the sensor is installed up side down 3 Unplug 1 sensor at a time to check for response Audible voice or warning sound is too low 1 Adjust the volume to a certain level Blurred image on the LCD monitor 1 Check whether there is dirt or water on the lens of the camera 2 Clean the lens with a wet cotton swab and then dry it with a soft clean cloth Parking assist lines is too high or too low 1 Adjust the parking assist lines properly according to P20 in the manual If the problem persists please follow these steps A For consumers contact your dealer or nearby service center B For installer or dealer 1 Check the wire connection 2 Replace the ECU and recheck the system 3 Test the sensors with certified ECU using a flat wooden board 4 Plug the certified sensors into the ECU and recheck 5 Email your questions to us and we will reply ASAP Warranty terms The unit is warranted for a limited period of time from the date of purchase In the unlikely event of a defect arising in this product when used in accordance with the manufacturer s instructions the parts would be repaired or replaced free of charge a It is required to show warranty card when making any warranty claims b The model and the unit s serial number must be the same a
5. anged sensor or camera may result in false warning occasionally Ensure that the self test procedure is completed the camera and all sensors are functioning before reversing Sensor and camera maintenance Do not wash the sensor camera with squirt gun or swab them forcibly Please wash car with lowpressure water Please melt the ice with warm water when the sensors camera is covered by ice Please clean the sensors camera with cloth or low pressure water when the sensors are covered by mud or snow Troubleshooting There is no image on the LCD monitor 1 Check whether the power supply wire is connected correctly 2 Check whether the ignition is turned to ACC ON 3 Check whether the reverse gear is selected 4 Check whether all the connections are correct 5 Check whether the video output plug is connected to the video in socket of the LCD monitor 6 Check whether the function setting of the monitor is correct 7 Check whether the camera is correctly connected to the ECU The monitor indicates a defective sensor 1 Check whether the sensor surface is clean 2 Check whether the sensor wires are plugged in the ECU properly 3 Check whether the sensor wires are damaged or not The object position does not correspond to that on the monitor 1 Are the sensor cables connected to the ECU in the correct order e g A B C D When reverse gear is selected 0 5m 0 6m will be shown on
6. ction accordingly Parking assist lines mode selection and adjustment Function test after installation The choice of parking assist lines mode is based on the camera type Mode 1 is for micro tab camera while mode 2 is for flush mount camera The width of rear view image is suggested to be the same as the width of the vehicle Parking assist lines adjustment a Select the reverse gear b Press and hold the MENU button to enter the parking assist lines mode Select mode 1 or mode 2 with A or V button Press SET button once to confirm the selection Press or V button to adjust the width of parking assist lines Press SET button to confirm the selection Use a flat board 1 0x1 5m standing behind the car reverse slowly to test each function respetively as shown in the manual
7. ith the sensors the system will beep three times to indicate that one Or more sensors are damaged About the parking assist lines Right obstacle distance indicator Green 2 59 1 6M Yellow 1 59 1 2M Yellow 1 19 0 9M Red 0 89 0 6M Red 0 59 0 3M i J u N The rear image Left obstacle distance indicator Green 2 59 1 6M Yellow 1 59 1 2M Yellow 1 19 0 9M Red 0 89 0 6M Red 0 59 0 3M 6 SET button Press the SET button to save and confirm the selection 7 Universal joint base The display can be adjusted to any direction to meet X Any damaged sensors should be replaced Obstacle distance the driver s requirement a a o Ea This picture indicates all sensors are functioning Parking assist lines and the obstacle distance is more than 2 59m Status preserving All the previous settings such as parking assist lines mode and color contrast etc will be saved after power off No further adjustment is needed when the power is on again Note e All the distances shown by parking assist lines are for reference only e For parking assist lines mode selection and adjustment please refer to page 20 How does the system work Parking assist lines mode 1 for micro tab camera Buzzer Be Be Be Be Be Be Be Be Display SPP aoeeneeveai F E L HTI r UH aii Buzzer Parking assist lines mode 2 for flush mount camera Display Be Be Be Be
8. nitor 2 OSD parking assist lines 3 Digital distance 1 Rearview on the LCD monitor The color camera automatically projects the image behind the car to the monitor once the reverse gear is engaged 2 Parking assist lines The space between the 2 vertical parking assist lines is equivalent to the width of your vehicle Any object in that space will hinder your reversing The color distance indicator will appear on the monitor when the vehicle is getting closer to the obstacle 3 Digital distance Detection range 0 3 2 5m The distance detected by the sensors will be shown on the left and right side of the monitor The digital number on the monitor will be refreshed every 0 1m When the obstacle distance is less than 0 3m STOP will be shown on the monitor and the speaker will beep continuously or say STOP when the voice warning is turned on 4 MENU button 5 A and V button 6 SET button 7 Universal joint base Rear 4 MENU button The MENU button is used to open the on screen display menu and to return to pevious menu 5 A and V button and V button are used to select voice on off and to adjust volume brightness contrast and color Self test function The system will test the sensors automatically when the reverse gear is selected 1 If all sensors are functioning the system will beep once 2 If there is any problem w
9. p pl STEEL MATE PTSV403 Automotive E 7 Camera Think safety think Steelmate eE System STEELMATE CO LTD www steel mate com All rights reserved The trademark patent and copyright are owned by Steelmate Co Ltd rear The right to change the design and specifications reserved PTSV403 75545485 Camera Sensor User s Manual Installation Manual Professional manufacturer with high quality standards Reasons to choose Steelmate Brief installation diagram Complete range of products you can easily Disclaimer Packing list select a product to match Important notice Installation tools There are agents distributors in more than 80 Key features Wire connection countries to supply local service About the product Sensor installation More than 100 engineers in the company you Technical specifications Camera installation can enjoy the latest technology About the monitor ECU installation More than 300 patents Self test function Monitor installation 6 Products have international approvals high sai i Camera Parking quality guaranteed About the parking assist lines Parking assist lines mode selection and adjustment Assist System Leading manufacturer in automotive industry l l ISO9001 ISO TS16949 ISO14001 and OSD setting Function test after installation User s Manual OHSAS18001 certified Attention How does the system work Sensor and camera maintenance Troubleshooting Warranty
10. s the information on the warranty card This warranty is non transferable and is automatically void if a The original purchaser has not completed the warranty card b The unit s serial number is defaced missing or altered c The unit has been modified or used in not to its intended purpose d The unit has been damaged by accident unreasonable use neglect improper installation or service The warranty does not cover a Damage caused by incorrect or poor installation problems which may be caused by anomalies in the vehicle s electrical system or originating from the environment in which the system is operated b Damage to the system caused by accident or improper use in any manner whatsoever not the fault of Steelmate including but not limited to damage by water or as a result of excess voltage applied to the system or if misused or repaired or altered in any way other than by Steelmate or it s authorized agent False information displayed in the panel of the dash board that is caused by car with CAN bus system Steelmate warranty card User Tel Vehicle Reg No Product Model No Serial No Date of Installation Name of the Retailer Signed by Retailer 13 Camera Parking Assist System Installation Manual Brief installation diagram Packing list Sensor Camera Hole saw Power harness Harness The actual sensor or camera may vary from the image shown above LCD monitor
11. terms Steelmate warranty card The camera parking assist system is designed as a driver assistance device and should not be used as a substitute for safe parking practices The area into which the vehicle is to be reversed must be constantly visually monitored while parking Steelmate and its distributors do not guarantee or assume liability for collisions or damages while reversing your vehicle Important notice About the product Steelmate parking assist systems help to provide assistance when reversing and parking Driving skills such as slowing down use of mirrors etc are always essential This unit is for vehicles with 12V DC only 2 This unit should be installed by a professional auto technician Route wiring harness away from heat sources and electrical components It is strongly recommended to check the position of the sensors before the actual drilling of the holes Perform tests after finishing the installation Key features e TFT LCD monitor with parking assist lines e OSD menu e Flush mount or micro tab camera available e Shock vibration and water resistant camera e PAL or NTSC mode available e Accurate digital distance and clear rearview shown on the monitor e Audible warning and voice warning optional volume adjustable e Self test function e Anti false alert technology PTSV403 is a camera parking assist system with parking assist lines shown on the TFT LCD monitor Turn ACC on
Download Pdf Manuals
Related Search