User Manual Power Express Software
Contents
1. Online Maximum 59 J Channel 2 Ch address 2 Function dimmer Label Short press Fade fi Oo Minimum 0 eee Long press Fade 5 On line Masmum 199 J Upload Fig 15 4 5 1 PEF 200 parameters description e Interface address 0 15 address of the module The addresses of both channels of this module are based on this value e Bank 0 9 module group e Filter 0 180 msec Minimum time of pressing the button for the press to be valid e Long press 0 900 msec If the time of pressing the button is longer than this value the press is interpreted as a long press The following parameters can be set for each channel independently e Function mode selection for control dimmers by it s buttons no action buttons are disabled toggle switch outputs between maximum and minimum values solid state if no button is pressed the output has the minimum value If one button is pressed the output has the value entered in the parameter Intermediate If both buttons are pressed the output has the maximum value dimmer a short press of the UP DOWN button changes the output value to maximum minimum at the speed set in the parameter Short press fade A long press makes the output dim up down at the speed set in the parameter Long press fade A release of the button makes it stop at the currently reached value If button down is held the value does not go all the way to 0 but stops at 1 For a total2. 4 3 2 Direct control of dimmable channels If the On line box is checked any changes made to the parameters Minimum Intermediate and Maximum are immediately transferred to the output of the module which makes it possible to control the real brightness of the light source If the On line switch is not activated the output of the module remains unchanged during setting The current value of the output is shown next to the On line being constantly updated User Manual PEX Software WWW CUe CZ Page 16 of 25 4 4 Configuration of the PEA 208 module PEA208 is a two channel analog output O 10V interface for devices with analog control O 10V dimmable ballast for fluorescent lamps Osram Siemens Helvar Philips dimmers frequency converters gt PEAZOS 2x analog output 0 10 Serial number CSu 02718 Firmware ver 1 7 Interface address i Filter eee ik ay eee Be Bank oo Long press mz a a a ae p gt Cha l Ch address 1 Function dimmer Label ooo Short press fade 1 0 s tinimu 0 an ba a a a E Long press fade s5 Z O Orire Masini 99 ee ea a a ad z Chameli gt gt Ch address 2 Function dimmer Label 0 Short press fade 4 0 Minimum J a i Lae ae Long press fade s5 M inina Maximum 38 e Upload Fig 14 4 4 1 PEA 208 parameters description e Interface address 0 15 address of the module The addresses of
3. e Bank 0 9 module group e Filter 0 180 msec Minimum time of pressing the button for the press to be valid e Long press 0 900 msec If time of pressing the button is longer than this value the press is interpreted as a long press The following parameters can be set for every channel independently e Function mode selection for control dimmers by it s buttons no action buttons are disabled toggle switch outputs between maximum and minimum values solid state if no button is pressed the output has the minimum value If one button is pressed the output has the value entered in the parameter Intermediate If both buttons are pressed the output has the maximum value dimmer a short press of the UP DOWN button changes the output value to maximum minimum at the speed set in the parameter Short press fade A long press makes the output dim up down at the speed set in the parameter Long press fade A release of the button makes it stop at the currently reached value Short press fade speed of dimming in case of normal button press 0 99 9 sec Long press fade speed of dimming in case of long time button press 0 99 9 sec Minimum minimum output value 0 99 Maximum maximum output value 0 99 Intermediate intermediate output value 0 99 for solid state mode User Manual PEX Software WWW CUe CZ Page 15 of 25 e Label Channel legend which can consist of up to 22 characters
4. channel addresses check e direct control of the dimmable or switcher channels 1 2 SVSteMm FEQUIFGIMEIIS siiis aa i e Computer PC 386 or better CD ROM drive e OS Windows 98 XP e 500 kB free space on HDD e free serial port User Manual PEX Software WWW CUe CZ Page 4 of 25 2 Installation and start of the PEX program 2 1 Program installation ccccccscsssessccsssesseeeeenseessonsenseeseonseeseoseeens The program is delivered on CUE Application CD Insert the CD to your computer run the file PEX_setup1605 exe and follow the installation wizard This file is placed in folder Software PEX 2 2 Start Ol the progra seciscesnsdccrscdsecussabtscanenanonsuaudueuswestuoeeusteispereanaseeeeae 2 2 1 Program start with modules Power Express online Link the Power Express system through the module PEC25 into the serial port of your computer All Power Express modules must have power supply Run the PEX program from the Windows Start menu R Microsoft Update Set Program Access and Defaults ea Windows Catalog r Program Updates rm i i x i Programs M Accessories PR Cue Director bY i hi Ee Documents I Games ae 7 peer E ge fn PEX 1 6 0 5 fal PES W Ci ettings r i Lae Startup Pg uninstall PS Search e Internet Explorer SA MSN Explorer a e o Help and Support E Outlook Express a i k SF Runs ee Remote Assistan
5. description e Interface address 0 31 address of the module The addresses of both channels of this module are based on this value e Bank 0 9 module group e Filter 0 180 msec minimum time of pressing the button for the press to be valid e Long press 0 900 msec If time of pressing the button is longer than this value the press is interpreted as along press The following parameters can be set for each channel independently e Function mode selection for control dimmer by it s buttons no action buttons are disabled toggle switch outputs between maximum and minimum values solid state if no button is pressed the output value has the minimum value If one button is pressed the output has the value entered in the parameter Intermediate If both buttons are pressed the output has the maximum value dimmer a short press of the UP DOWN button changes the output value to maximum minimum at the speed set in the parameter Short press fade A long press makes the output dim up down at the speed set in the parameter Long press fade A release of the button makes it stop at the currently reached value Short press fade speed of dimming in case of normal button press 0 99 9 sec Long press fade speed of dimming in case of long time button press 0 99 9 sec Minimum minimum output value 0 99 Maximum maximum output value 0 99 Intermediate intermediate output value 0 99 for solid state mode User Manual PEX
6. from the module can be recovered by pressing UPLOAD or Alt U Pressing DOWNLOAD or Alt D transfers the current parameters into the configured module User Manual PEX Software WWW CUe CZ Page 10 of 25 4 1 Configuration of the PER 610 module PER610 is a six channel relay switching unit for loads up to 10 A per channel There are all changeable parameters in the configuration window of the module The parameters in the upper part of the window are shared by all channels of the module PER610 6x relay max 10A Senal number CS0 602398 Firmware ver 1 8 Interlace address 1 Filter m i Bank Long press m T E Channel Ch addr Funkction Time 3 Parameter Label On line 5 1 balcony light o0 toilet fan 150 F drapes bedroom 150 4 drapes bedroom bedroom light Upload Fig 10 4 1 1 PER 610 parameters description e Interface address 0 15 address of the module The addresses of all channels of this module are based on this value e Bank 0 9 module group e Filter 0 180 msec minimum time of pressing the button for the press to be valid e Long press 0 900 msec If the time of pressing the button is longer than this value the press is interpreted as a long press The following parameters can be set for each channel independently e Function mode selection for control relay by its buttons noaction buttons are disabled coded Each press causes the nega
7. longest avilable time is 12 hours 59 minutes 2 30 nm 12 59 hhmm e Label Channel legend which can consist of up to 22 characters 4 1 2 Direct control of the channels Parameter Label U gt line I balconi light i toilet furi z toilet light P tapes bedroom a bedroom light e Fig 11 If you check off the On line box the current state of the on and off outputs is shown next to the channel names being constantly updated An output that is off is indicated by an activated button Clicking the button of the desired channel causes the negation of the output state User Manual PEX Software WWW CUe CZ Page 12 of 25 4 2 Configuration of one channel dimming modules PED 108 PET 102 and PET 105 PED108 is a one channel dimmer for resistive and inductive loads up to 8 A PET102 is a one channel dimmer for resistive and capacitive loads up to 2 A suitable for dimmable electronic transformers PET105 is a one channel dimmer for resistive and capacitive loads up to 5 A suitable for dimmable electronic transformers PED108 1x dimmer max 64 serial number CS0164 00276 Firmware wer 1 4 Interface address 0 aa Filter 40 me Eeee Bank W Lorg press ms a eee m Channel 1 Ch address Function dimmer Label Shorl press fade 7 1 amp Minimumo 1 Lonc press fade 3 M Ordine Maximum 99 Fig 12 4 2 1 PED 108 PET 102 PET 105 parameters
8. CUE a s NOTICE TO END USER CAREFULLY READ THE FOLLOWING LEGAL AGREEMENT THIS LICENSE INSTALLATION OR USE OF THE ENCLOSED CUE a s SOFTWARE PROGRAMS COLLECTIVELY SOFTWARE ON YOUR COMPUTER SYSTEMS OR HARDWARE DEVICES CONSTITUTES YOUR ACCEPTANCE OF THESE TERMS IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE PROMPTLY DELETE THE SOFTWARE FROM YOUR COMPUTER SYSTEMS AND HARDWARE DEVICES DESTROY ANY COPIES YOU MADE OF THE SOFTWARE OR ANY INSTALLATION MEDIA OF THE SOFTWARE INCLUDED WITH YOUR SYSTEM AND DISPOSE OF ALL WRITTEN MATERIALS IN YOUR POSSESSION REGARDING THE SOFTWARE License Grant CUE grants to You as an individual a license to install and use one 1 copy of the Software on a single computer at a time provided however that You may make copies of the Software solely for Your development of applications for CUE hardware and demonstration versions of such applications Any applications created with the Software may only be used with Cue hardware Your license to use the Software is conditioned upon Your compliance with the terms of this License A License is required for each end user of the Software A license is required for each installation of the Software You may make one 1 copy of the Software for archival purposes only You may use this Software only in connection with CUE hardware You must have acquired the Software directly in connection with the purchase of CUE hardware from CUE or from a CUE approved reseller for this
9. Long press fade 5 Drine Maimam 59 N Ss a Ch address 2 Function dimmer Label fluorescent row 7 12 Short press fade 1 0 tdinimum WoT ao Se p a Long press fade As T On line kl axirriuirn g9 ae aa A 4 15 Channel Ch address Label Configure DALI Iv 3 3 fluorescent row 1 Ch address Labek M 4 d fluorescent row 2 Ww 10 10 fluorescent row amp Je 5 z fluorescent row 3 Ww 11 l fluorescent row 9 m B G fluorescent row 4 w l2 12 fluorescent row 10 e zl 7 Jilucrescent row 5 w 13 12 fluorescent row 11 I a 5 fluorescent row 6 mw 14 fluorescent row 12 I g g fluorescent row F Ww 15 spare Fig 16 4 6 1 PEF 150 parameters description e Interface address address of the module The addresses of both channels of this module are based on this value e Bank 0 9 module group e Filter 0 180 msec Minimum time of pressing the button for the press to be valid e Long press 0 900 msec If the time of pressing the button is longer than this value the press is interpreted as a long press The followingparameters can be set for the first and second channel independently These channels can be controlled by buttons The number of channels equals the number of controlled DALI groups e Function mode selection for control dimmers by its buttons no action buttons are disabled toggle switch outputs between maximum and minimum values solid state if no button is pre
10. Software WWW CUe CZ Page 13 of 25 e Label Channel legend which can consist of up to 22 characters 4 2 2 Direct control of dimmable channels If the On line box is checked any changes made to the parameters Minimum Intermediate and Maximum are immediately transferred to the output of the module which makes it possible to control the real brightness of the light source If the On line switch is not activated the output of the module remains unchanged during setting The current value of the output is shown next to the On line being constantly updated User Manual PEX Software WWW CUe CZ Page 14 of 25 4 3 Configuration of the PED 202 module PED202 is a two channel dimmer for resistive and inductive loads up to 2 7 A per channel max 4A total PED2O2 2x dimmer max 7A Seral number CSO165 00340 Firmware wer 1 4 Interface address 0 Filler ne EN Bank 0 4 Long press a0 ns o FT Chaririel 1 SS Ch address fi Function dmmer Label Short press fade fi O hd ininuinn fo me E Long press fade 5 amp Online Maximum 39 n Channel 2 Ch address Function solid atate Label Short press Fade f O Piinia fo 2 Eoee e Intermediate 50 D On line Mavimum i99 lt A E Upload 4 3 1 PED 202 parameters description e Interface address 0 15 address of the module The addresses of both channels of this module are based on this value
11. User Manual PEX Software User Manual PEX Software UM031_01 30 05 2007 Copyright CUE a s Praha Czech Republic 1996 2007 All rights reserved Specifications are subject to change without prior notice Table of Contents Mer O CUCU ON asai a E RARA O AE EEEE EAERI EERE 4 1 1 Program descriptio Misereor i eS eet ee ie ha eee i te eit el lee ees 4 1 2 System reguleren iinet ee tei eee se cee me rte ieee es ee ete eel cet eee ce eta ainl Sete 4 2 Installation and start of the PEX program ciiwciscscssccisedeescscedss dis cisccedececesaewsstiiediveanecctsecsdesiesiidenaieets 5 21 FPOgaminstalaloNkeeris a a eens canets tencescum th tadeecacureresaas 5 2 2 Sar Ol ANS pogra i een ae a A oud vetaiaastaonadeaiueddassondeasetecs 5 3 Program operating sier aa Ea Oa araea AAAA 7 3 1 Command meni sirien tans mantras cel tandlaciaet soa be naecta a teats catoet Banu deatanaannee bonduce ecentsaaseenes 7 3 2 SEISCHING COMMMAN GS memesi a r dead aT E T 7 333 ement AlE aa abou a an iabde ed N a 7 3 4 Opions Meng AI sacecsecegecrcensecsse reget a 7 3 5 LOOC NEA Meaney wetaners rece serene sere ern ec eMC te rinse er een aot Me Nea ner Oe Me ene re ie ee eee oe mer eee ee 8 3 6 HED MEn Bastar Vase A E r eE AA ES 9 4 Configuration of the Power Express modules cccccsssseeeeeeeeseceeeeneeeeeeeeeeeeeseeeeeeseeennneeeeees 10 4 1 Configuration of the PER 610 module ccccceececcccceeeeeeeseeeeeeeeeeaeeeceeeeeeee
12. both channels of this module are based on this value e Bank 0 9 module group e Filter 0 180 msec Minimum time of pressing the button for the press to be valid e Long press 0 900 msec If the time of pressing the button is longer than this value the press is interpreted as a long press The following parameters can be set for each channel independently e Function mode selection for control dimmers by it s buttons no action buttons are disabled toggle switch outputs between maximum and minimum values solid state if no button is pressed the output has the minimum value If one button is pressed the output has the value entered in the parameter Intermediate If both buttons are pressed the output has the maximum value dimmer a short press of the UP DOWN button changes the output value to maximum minimum at the speed set in the parameter Short press fade A long press makes the output dim up down at the speed set in the parameter Long press fade A release of the button makes it stop at the currently reached value fluorescent a short press of the UP DOWN button changes the output value to maximum minimum at the speed set in the parameter Short press fade A long press makes the output dim up down at the speed set in the parameter Long press fade A release of the User Manual PEX Software WWW CUe CZ Page 17 of 25 button makes it stop at the currently reached value If button down is held the val
13. ce H 2E windows Media Player EJ 0 Shot Down kaa Messens ig Start Ce Fig 1 Once you have loaded the program the main program window will be displayed There is a list of the connected modules with their serial numbers on the left side of the main window and a space for their parameters on the right side of the window User Manual PEX Software www cue cz Page 5 of 25 Command Full serial number Einnar version menu of the module Tools Help PERG10 6x relay max 104 Serial number CSO167 00348 List of the connected Firmware ver 1 3 modules i Interace address Filter ms p A Bank jo Long press m a NUM BS ol ices Channel Ch addr 9 Funketion Time s Parameter Label E 1 i coded bi living room 2 2 coded Jliving room 2 3 coded hi bedroom 4 E coded bi kitchen 5 E coded childem s room Editable module B E coded ae garden 1 parameter Upload invinlged eee eee em Eo er ey ey a a ce Upload Download parameters parameters into from module module Fig 2 2 2 2 Program start without modules Power Express connected The PEX program can be run without modules Power Express connected There is a notice on the startup in such case No interlace was found Check the connection of select another serial port please Fig 3 User Manual PEX Software www cue cz Page 6 of 25 3 1 Command MO NU ccccececcccecec
14. choose the chart for analog or digital channels User Manual PEX Software WWW CUe CZ Page 8 of 25 OR PEFZO0O 0K PED108 0K PER610 CONFLICT PER610 0K PER610 CONFLICT PER610 0K PER610 CONFLICT PER610 OK PER6E10 CONFLICT PER610 0K PER610 CONFLICT PER610 0K PER610 CONFLICT PER610 AnMNnN OK KRHOOWONNRrPRE Ee Fig 9 lf there is a conflict in addressing the warning CONFLICT is shown in the column Status at conflict channels Double click the right mouse button on the selected channels in the list open configuration window of the relevant module 20 FEID MENU er E neces eseeerenssanves About Shows a window with the program version and contact addresses of producers User Manual PEX Software www cue cz Page 9 of 25 4 Configuration of the Power Express modules Double click the module list in the main window to show editable parameters of the module You can change parameters by type writing Label living roor selecting from a list of options Channel Ch addr Funketion T 1 I zoded 2 2 i 3 2 4 E increasing or decreasing numerical values or Interface address fo E Bank E dragging scroll bars Fiter 40 ms z meee If the value of any parameter is changed its background flashes red to indicate change If you move the mouse cursor to ten given parameter its previous value is shown Before the transmission of new parameters the original values
15. eeeeeceeeesssaeasseeeeeessaaaaeeess 11 4 2 Configuration of one channel dimming modules PED 108 PET 102 and PET 105 ees 13 4 3 Contiouration ot the PED 202 module seri a abide Rete 15 4 4 Configuration olhe PEA 208 MOUE anepria re a e T TRT 17 4 5 Configuration of the PEF 200 MO dU G x cesses aiir a aid nee a a aa a aa a 19 4 6 Configuration of the PEF 150 MOdUle ccccccceccccceeeeeeeseeeeeeeeeeeeeeeeeeeeesseeeeeseeeeesseeaeeeeeeeesssaeaeeess 21 5 Software and Firmware License ssssssuuunssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmn n nn nnnnnnnnn nnmnnn nnmnnn nnana 24 User Manual PEX Software WWW CUe CZ Page 3 of 25 1 Introduction 1 1 Program description vesiscsscdericevecurscesedccvoassasarcassccsscetucudieestesvecssemswessa The PEX program is designed for an easy configuration of the Power Express system modules The program features e configuration of the dual channel analog outputs of the module PEA208 e configuration of the one channel dimmer module PED 108 e configuration of the dual channel dimmer module PED 202 e configuration of the module PEF 150 for control of the fluorescent tubes dimmable ballasts DALI e configuration of the module PEF 200 for control of the fluorescent tubes dimmable ballasts DSI e configuration of the 6 relays module PER 610 e configuration of the one channel transistor dimmer PET 102 e configuration of the one channel transistor dimmer PET 105 e
16. er rights CUE may terminate this License if You fail to comply with its terms and conditions In such event You must immediately destroy all copies of the Software No Other Warranties CUE DOES NOT WARRANT THAT THE SOFTWARE AND FIRMWARE IS ERROR FREE CUE DISCLAIMS ALL WARRANTIES WITH RESPECT TO THE SOFTWARE AND FIRMWARE EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS OF HOW LONG AN IMPLIED WARRANTY MAY LAST OR THE EXCLUSION OF LIMITATION OF INCIDENTAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION No Liability for Consequential Damages IN NO EVENT SHALL CUE BE LIABLE TO YOU FOR ANY CONSEQUENTIAL SPECIAL INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE PERFORMANCE OR USE OF THE SOFTWARE EVEN IF CUE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Label on Hardware Use of this hardware and the software programs controlling this hardware is subject to the terms of the Software and Hardware License Agreements the License Agreements You should not use the software and hardware until you have read the License Agreements By using the software and hardware you signify that y
17. hortcut User Manual PEX Software WWW CUe CZ Page 7 of 25 3 5 Tools menu AU U scccesiscansaccennnccadcanteadsanseaneseessaeancteuavessseaseaccateeaunanuansans LOCATE F3 By this command you can seek a channel without knowing its address by pressing its button on the module Press test button on located interface for 3 sec Testing interface with serial number 00348 Fig 6 You can STOP this function by pressing the STOP button If there is more than one channel with the same address the LOCATE command does not run and a warning message is shown PEX Program was found more interfaces with same bank and address conflict can t continued Fig 7 ADRESS CHECK F4 This command is used to check the addresses of all connected modules A special window opens to display the results of this command There is a list of all connected channels on the right side of the window Address check irene Bank Addr Status Interface Serial n Channel e 3 5 ae ai OlZS45678901F34 56789012 3456789012 FEFZOO FED 1O8 FERE1O FPERE1O PERG1O PERSG1O PERE1O PERE1O FERE1O FERE1O PERE1O ank PERE1O PERSG1O PERE1O Moo lI hon kw e oO Hao hk WM Poo ek om re Re PS g occuped O one conflict W more conflicts OF Fig 8 In the left part of the screen there is a chart clearly showing the positioning of channel addresses of the given type By selecting the type of output in the list A or D in the Bank column you
18. license to be effective If You have purchased a Site License You may complete only the number of installations specified in the License Agreement accompanying the Software Copyright The Software and software built into CUE hardware Firmware are protected by copyright law and international treaty provisions You acknowledge that no title to the intellectual property in the Software and Firmware is transferred to You You further acknowledge that title and full ownership rights to the Software and Firmware will remain the exclusive property of CUE and You will not acquire any rights to the Software and Firmware except as expressly set forth in this License You agree that any copies of the Software will contain the same proprietary notices which appear on and in the Software Prohibited Uses Without obtaining prior written permission from CUE You may not a use copy modify alter or transfer the Software or documentation except as expressly provided in this License b translate disassemble decompile reverse program or otherwise reverse engineer the Software and Firmware c sublicense or lease the Software or its documentation d use this Software with any hardware other than products produced by CUE or in connection with applications being developed for CUE hardware or e use the Software in a multi user network or multiple computer environment or in a rental time sharing or computer service business Without prejudice to any oth
19. luorescent row 4 C fluorescent row 5 Fluor tube Mfluorescent row B blinking C Fluorescent row fluorescent row 8 C fluorescent row 9 aoe C Fluorescent row 10 Configurate C Fluorescent row 11 fluorescent row 12 _ spare All on The group on Fade all Fade the group All off The group off Close Fig 19 Wd til d There is a list of all found ballasts on the right side of the screen The tube of the sellected ballast is blinking for easy identification of the chosen light in the room After you have locallised the light you can assign it into one ore more channels groups listed in the left part of the screen The blinking of the tube can be stoped by pressing the Fluor tube blinking button There are some other options such as switching on all ballasts to the maximum by pressing the All on button fading them to the minimum by pressing Fade all or switching them off by pressing All off to the m in a chosen group The same commands can be carried out for a whole group by pressing Group on Fade group or Group off Reset ballasts resets all ballasts while all ballast addresses as well as all grouping into channels ale deleted The Configurate button starts configuration of ballasts all over again The Close button ends the configuration and closes the configuration window User Manual PEX Software WWW CUe CZ Page 23 of 25 5 Software and Firmware License END USER NOTICE AND LICENSE AGREEMENT FROM
20. ou have read the Licenses Agreements and accept their terms The License Agreement is available at www cuesysiem com Trademark Notice CUE and the CUE logo are trademarks of CUE a s in the United States and in other countries User Manual PEX Software WWW CUe CZ Page 24 of 25 User Manual PEX Software WWW CUe CZ Page 25 of 25
21. rent value of the output is shown next to the On line being constantly updated 4 6 3 DALI ballasts configuration by PEF 150 module After connecting PEF150 to the DALI bus which is connected to max 63 ballasts it is necessary to set the addresses in DALI ballasts and assign them into groups These can be controlled from the PEF 150 control module You can start this configuration by pressing the Configure DALI button That starts an initialization and a test of the ballast s addresses If the addresses of ballasts do not come in a continuous sequence configuration has not yet been carried out the following message is shown PEX Found ballasts have no continuity addresses Search address again Fig 17 If you select Yes the control of addresses runs again Otherwise the program asks you when you want to start setting addresses User Manual PEX Software WWW CUe CZ Page 22 of 25 Start setting addresses YES NO Fig 18 Once you have confirmed by pressing Yes ally adresses of ballasts are deleted information about groups remain saved and a new assigning of addresses for a given set of ballasts is carried out Once everyvery founded ballast has its short address a form for assigning ballasts into channels groups is shown Group list Ballasts fluorescent row 1 6 EE Reset ballasts C fluorescent row f 12 fluorescent row 1 Next gt C Fluorescent row 2 Ue fluorescent row 3 f
22. sncececeneecsnencecenenceaeaeeceaeaeeeeneneeaeneeesaeneness g PEX File Uptons Toole Help Je SEISCUING COMMANA S merinin E E You can select commands in the usual way from the menu or you can use the keyboard shortcuts for example ALT O to open the Option part of the menu d PEX File Oplions Tools Help Select seral port d E w Panty check Com Quick communication Reset FS 3 3 File menu Alt F aannannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnna e OPEN Ctr O to open the project with configuration of the modules of the Power Express system from the file e SAVE Ctr S to save the actual project into the file e SAVE AS to save the current project into the file with a new name e EXPORT to export the actual project as file for Excel csv Internet Explorer htm Plain text txt e EXIT to terminate the PEX program 2A OPUONS MENUA NFO soeia E RA e SELECT SERIAL PORT shows the list of all free serial ports in computers The marked port is selected for the communication with the modules of the Power Express system If you select any other serial port the program performs RESET and loads data from new selected port e PARITY CHECK switches on off communication parity check e QUICK COMMUNICATIONS switches on off quick e RESET F5 The program carries out a new load of the connected modules of the Power Express system You can also do it by pressing the F5 keyboard s
23. ssed the output has the minimum value If one button is pressed the output has the value entered in the parameter Intermediate If both buttons are pressed the output has the maximum value dimmer a short press of the UP DOWN button changes the output value to maximum minimum at the speed set in the parameter Short press fade A long press makes the output dim up down at the speed set in the parameter Long press fade A release of the User Manual PEX Software WWW CUe CZ Page 21 of 25 button makes it stop at the currently reached value If button down is held the value does not go all the way to 0 but stops at 1 For a total switch off use repeated quick press hort press fade speed of dimming in case of normal button press 0 99 9 sec Long press fade speed of dimming in case of long time button press 0 99 9 sec Minimum minimum output value 0 99 Maximum maximum output value 0 99 Intermediate intermediate output value 0 99 for solid state mode e Label Channel legend which can consist of up to 22 characters 4 6 2 Direct control of dimmable channels If the On line box is checked any changes made to the parameters Minimum Intermediate and Maximum are immediately transferred to the output of the module which makes it possible to control the real brightness of the light source If the On line switch is not activated the output of the module remains unchanged during setting The cur
24. switch off use repeated quick press Short press fade speed of dimming in case of normal button press 0 99 9 sec Long press fade speed of dimming in case of long time button press 0 99 9 sec Minimum minimum output value 0 99 Maximum maximum output value 0 99 Intermediate intermediate output value 0 99 for solid state mode User Manual PEX Software WWW CUe CZ Page 19 of 25 e Label Channel legend which can consist of up to 22 characters 4 5 2 Direct control of dimmable channels If the On line box is checked any changes made to the parameters Minimum Intermediate and Maximum are immediately transferred to the output of the module which makes it possible to control the real brightness of the light source If the On line switch is not activated the output of the module remains unchanged during setting The current value of the output is shown next to the On line being constantly updated User Manual PEX Software WWW CUe CZ Page 20 of 25 4 6 Configuration of the PEF 150 module PEF150 is interface for control up to 64 dimmable ballasts for fluorescent lamps on one bus divided up to 15 independent groups PEF150 1x dimmer S nal number CSxxxx 05399 Firmware ver 1 07 Inlerface address oo Filter f 4d me booa a I PA pawe supp Bank oo Long press ms ze p17 Channel Ch address Function dimmer Label fluorescent row 1 6 Short press fade 1 0 z Minimurn 0 a E N N ANTE
25. tion of the relay state switched on off relay When button is pressed the output is on otherwise it is off system on When pressed the relay switches on it can be switched off only by a command through serial line User Manual PEX Software WWW CUe CZ Page 11 of 25 run ashort press switches the relay on for the period of time entered in its parameter Long time press do the relay on only for button is holding It is useful in couple with other channel with direction mode for controlling of AC motors direction it is useful for selecting direction of controlled AC motors After 200 ms the couple relay with mode run is switched on too delayed off the relay is switched on at once but it is switched off after delay time delayed on the relay is switched off at once but it is switched on after delay time run DC firmware 1 09 or higher short press switch relay on for parameter time Long time press do the relay on only for button is holding It is useful in couple with other channel with same mode for controlling DC motors pulse firmware 1 10 or later the relay is switched on for a short time impulse entered in the parameter e Time parameter in seconds for modes working with time There are the following time formats available for units with firmware 1 11 or higher Tine seconds 0 1 999 9 s 10lsec minutes seconds 00 01 59 59 hours minutes 00 01 12 59
26. ue does not go all the way to 0 but stops at 5 For a total switch off use repeated quick press hort press fade speed of dimming in case of normal button press 0 99 9 sec Long press fade speed of dimming in case of long time button press 0 99 9 sec Minimum minimum output value 0 99 Maximum maximum output value 0 99 Intermediate intermediate output value 0 99 for solid state mode e Label Channel legend which can consist of up to 22 characters 4 4 2 Direct control of dimmable channels If the On line box is checked any changes made to the parameters Minimum Intermediate and Maximum are immediately transferred to the output of the module which makes it possible to control the real brightness of the light source If the On line switch is not activated the output of the module remains unchanged during setting The current value of the output is shown next to the On line being constantly updated User Manual PEX Software WWW CUe CZ Page 18 of 25 4 5 Configuration of the PEF 200 module PEF200 is a two channel interface for fluorescent lamp dimming ballasts with DSI control signal TRIDONIC ZUMTOBEL PEF200 2x dimmer enal number CSO166 00379 Firmware wer 1 4 Interlace address E i Filter ns lt Bank ae Long press 400 ms Channel 1 Ch address 1 Furctior dimmer Label Short press Fade fi 0 Minimum jo 203 Long press fade 5
Download Pdf Manuals
Related Search