Tunable OTN XFP Tuning by Channel Upgrade GUI User Manual
Contents
1. Board and connect the USB to serial cable to the PC Connect to the Host Board 9 pin D sub connector via the USB to serial cable Launch the WL Tunability software from the Start gt Programs gt Menara folder NOTE Use the WL Tunability Editor for the Host Board or USB Tuning cable Select the proper COM port or select Port Auto Search if the COM port is not known as shown below AP ey se AA Menara Networks Xi Al Open Communications Search for the Com Port or Enter Manually to connect to the module Port Auto Search Manual ComPort 1 4 Open 7 Insert the XFP into the host board or USB Tuning Cable June 2012 CONFIDENTIAL amp PROPRIETARY 2 enara Menara Networks 002 40001 00 A NETWORKS 8 Inthe Tunability box verify that the Tunable by DWDM Wavelength is checked as shown below M Menara Networks XFP WL Tunability Editor knd XFP Tunability check or uncheck selection Serial No PartNo 418806A 1600 unable DWDM by Wavelength Rev E 9 If Tunable DWDM by Wavelength is NOT checked then the XFP is correctly setup and no additional steps are required The module can be removed 10 If the Tunable DWDM by Wavelength IS checked as shown above then uncheck the box as shown below Once the box is un checked the GUI will change the XFP to disable the wavelength tuning function During this time the red DO NOT REMOVE MODULE text is shown M Menara N2. News Menara Networks 002 40001 00 A Wavelength Tunability Editor User Manual 020 40001 00 A June 2012 CONFIDENTIAL amp PROPRIETARY 1 enara Menara Networks 002 40001 00 A NETWORKS 1 Introduction The Wavelength Tunability Editor is designed to disable the tuning by wavelength option in the Menara tunable XFP It is necessary to disable this setting to force the Juniper router to properly tune the Tunable OTN XFP by channel number instead of wavelength The XFP can still be tuned using channel numbers via the JUNOS or the Menara host board and USB tuning cable 1 1 Equipment needed e Menara Tunable OTN XFP ONLY C BAND TUNABLE XFPs apply for this change e Menara host board or Tuning Cable e USB to serial cable 1 2 Download and Installation instructions 1 Download the software at www menaranet com GUI Note There are separate versions for either the Host Board or USB Tuning GUI Be sure to download and install the proper version If not previously installed the USB Tuning Cable version requires a driver be installed for use on the PC The driver is included in the Tuning Cable folder Extract the software to a location and run the setup exe file Follow the installation instructions wo N 2 Operating Instructions DO NOT INSERT the XFP into the HOST BOARD or USB TUNING CABLE at this time If using the USB Tuning Cable insert the USB cable into the PC and skip to step 5 Power up the Host
3. etworks XFP WL Tunability Editor XFP Tunability check or uncheck selection Serial No 11330614 Part No 418806A 1600 Tunable DWDM by Wavelength Rev E DO NOT REMOVE MODULE 11 Press the reset button as shown below to verify the change M Menara Networks XFP WL Tunability Editor XFP Tunability check or uncheck selection Serial No 11330614 PartNo 418806A 1600 Tunable DWDM by Wavelength Rev E Reset to take affect J 12 Once the reset is completed verify that the serial number has been appended with A as shown below and the check box is NOT checked June 2012 CONFIDENTIAL amp PROPRIETARY 3 enara Menara Networks 002 40001 00 A NETWORKS Tunability check or uncheck selection PartNo 418806A 1600 E Tunable DWDM by Wavelength Rev E 13 The module has been succesfully converted It is now safe to remove the module June 2012 CONFIDENTIAL amp PROPRIETARY 4
Download Pdf Manuals
Related Search