USER`S gUidE
Contents
1. 22mm 26mm 11 1 4 1 1 2 P 286mm 38mm 1 BOTTOM KO T 25mm 8 7 8 6 11 16 aloe 203mm 22mm 170mm 31mm 31516 4 101mm FRONT SDE INSTALLATION N N B Cut off power supply at circuit breaker fuse before proceeding to the installation and wiring a connections This product must be connected by a certified electrician according to the electrical and piecami L building codes effective in your region Consult the wiring plan found on the unit SURAE il INSTALLATION To reduce the risk of fire do not store or use gasoline or other flammable vapors and liquids in the vicinity i of the heater Do not mount in contact with combustible material Do not mount in close proximity to ig 4043 i 8 1 2 a zi another anit 216 mm nstactarion 266 mm DANGER High temperatures may be generated under certain abnormal conditions Do not partially or LI fully cover or obstruct the front of this heater 47 8 12 9 16 Important This heater should be installed at no less than 8 20 3 cm from the finished floor and 4 peal 319 mm 10 cm from adjacent walls BACK This heater has been designed for a permanent wall installation in a bathroom either surface or recess mounted 1292 mm acct a 1 Make an opening in the wall which is 16 1 2 419 mm high by 11 1 2 292 mm wide 2 Remove the control knobs thermostat knob top and timer knob bottom 3 Re2. O USER S GUIDE ASIL2030 SERIES STELPRO BATHROOM FAN HEATER 360 comfort REPLACEMENT COMPONENT LIST INCLUDED amp S This unit complies with the CSA and UL standards For further information or to consult this guide online please visit our website at www stelpro com INSASIL20300514 WARNING IMPORTANT INSTRUCTIONS Before installing and operating this product the user and or installer must read understand and follow these instructions and keep them handy for future reference If these instructions are not followed the warranty will be considered null and void and the manufacturer deems no further responsibility for this product This product must be installed by a qualified person and connected by a certified electrician according to the electrical and building codes effective in your region The following instructions must be adhered to in order to avoid personal injuries or property damages serious injuries and potentially fatal electric shocks Protect the heating unit with the appropriate circuit breaker or fuse in accordance with the nameplate Make sure the line voltage volt is consistent with that indicated on the unit s nameplate This unit must be grounded Switch off the power at the circuit breaker fuse before installing repairing and cleaning the unit Make sure the unit is appropriate for the intended use if needed refer to the product catalog or a representative Use this heater only as de
3. an that written on the nameplate e Heat losses higher than the unit capacity The desired room temperature cannot be reached N B If you do not solve the problem after checking these points cut off the power supply at the main electrical panel and contact our customer service see the Limited warranty section to obtain the phone numbers REPLACEMENT COMPONENTLIST J ENT COMPONENT LIST REF PART DESCRIPTION 1 BOUT 250 THERMOSTAT TIMER KNOB WHITE 1 BOUT 250 A THERMOSTAT TIMER KNOB ALMOND 2 ELF 250 INTEGRATED ELEMENT PROTECTION 3 MO 250 MOTORY FAN 240V 4 M SIL203000C1 TOP GRILL 5 M SIL203003Z1 FRONT COVER 6 ST 017 THERMOSTAT SP y TIM 250 TIMER 30 MIN FLK SIL2030 FUSE LINK KIT rO INSASIL20300514 LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY This limited warranty is offered by Stelpro Design inc Stelpro and applies to the following product made by Stelpro model ASIL2030 Please read this limited warranty carefully Subject to the terms of this warranty Stelpro warrants its products and their components against defects in workmanship and or materials for the following periods from the date of purchase 5 years This warranty applies only to the original purchaser it is non transferable and cannot be extended CLAIM PROCEDURE If at any time during the warranty period the unit becomes defective you must cut off the power supply at
4. commended that a qualified electrician or a certified repair centre examine the unit in order to make sure it is not damaged Refer to the limited warranty If you set the thermostat to the lowest temperature set point the Frost free warning mode will be activated since there is no OFF position Before unplugging the unit all controls must be in the OFF position and the current from the main breaker panel should be cut The general switch may be used also if included If the unit is damaged or defective discontinue use cut off power supply at circuit breaker and contact a certified electrician or certified repair centre Refer to the limited warranty SAVE THESE INSTRUCTIONS Note When a part of the product specification must be changed to improve operability or other functions priority is given to the product specification itself In such instances the instruction manual may not entirely match all the functions of the actual product Therefore the actual product and packaging as well as the name and illustration may differ from the manual cay a INSASIL20300514 SPECIFICATIONS TECHNICAL DRAWINGS amp INSTALLATION SPECIFICATIONS VOLTS 240 V WATTS 1000 2000 W WEIGHT 12 1 LB 4 9 KG DEPTH 4 101 MM WIDTH 13 3 8 340 MM HEIGHT 17 3 8 441 MM TECHNICAL DRAWINGS 13 3 8 340mm i KO 7 8 122mm 17 3 8 15 7 8 441 403mm KO 7 8 11 16
5. cost of disconnection transport and installation ALNVYYVM G3ALINI1 The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price at the discretion of Stelpro Any parts replaced or repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty period This warranty will be considered null and void and Stelpro will have the right to refuse any claims if products have been altered without the written authorization of Stelpro and if the nameplate numbers have been removed or modified This warranty does not cover scratches dents corrosion or discoloration caused by excessive heat chemical cleaning products and abrasive agents It does not cover any damage that occurred during the shipping Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations on how long an implied warranty lasts so these exclusions or limitations may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state or from province to province LIMITED WARRANTY ALNVYYVM Q3LINIIT ALNVYYUVM QALIWI ALNVYYVM Q3LINWII STELPRO DESIGN INC Saint Bruno de Montarville Qu bec J3V 6L7 6 INSASIL20300514
6. ct with a water source such as but not limited to showers bathtubs sinks toilets etc and must be protected from splashes Do not use it if any part has been immersed Moreover do not turn it on or off when standing in water or if your hands are wet When mounting the unit make sure that the anchorage used can support the total weight of the unit with the mounting brackets When cutting or drilling into a wall do not damage electrical wiring and other hidden utilities When starting up the unit for the first time or after a long period it is normal that it produces some temporary odours and whitish smoke Because this unit is hot when in use it may pose risks even in normal operation Therefore be careful and responsible when using it To avoid burns do not let bare skin touch hot surfaces The unit must cool down for few minutes since it will stay warm for some time after shut down Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended The bottom of this unit must be installed at least 8 inches 20 3 cm from the floor and the whole unit must be installed at least 4 inches 10 cm from walls However make sure objects or pieces of furniture do not come into contact with the unit and keep them at least 12 inches 30 cm from the unit since they are more flammable than walls and floors Failure to comply with this warning could lead to a fire Some materia
7. e properly installed before it is used Thermostat features Maintains a stable room temperature Highest setting offers continuous operation of heater Thermostat settings correspond to desired room temperatures and ensure the cycling of the heater Thermostat will not engage the heater to operate when the room temperature is higher than the thermostat setting 5 i B Thermostat will engage heater to operate continuously when the room temperature is lower than the thermostat setting 20 15 This bathroom heater has been designed for a permanent installation and offers several heating modes 2000W NORMAL HEAT MODE RAPID HEAT MODE Turn the thermostat A clockwise to its halfway point Set the timer B for the amount of time you wish to heat the room The heater will now operate at 2000 W for the duration set by the The heater will now operate at 1000 W A timer Should the desired room temperature be too low turn the thermostat A clockwise to increase the temperature Should the desired room temperature be too high turn the thermostat counter clockwise to decrease the temperature COMBINED RAPID NORMAL HEAT MODES Set the timer B for the duration you wish to heat at 2000 W Set the thermostat A to the desired temperature The heater will operate at 2000 W for the selected timer duration and once the time has expired the heater will continue to operate normally with the thermostat offering 1000 W to maintain the des
8. ired room temperature MAINTENANCE All other repairs and maintenance other than those described in Do not use cleaning products identified with these symbols this guide should be performed by qualified service personnel In order for the warranty to be valid the unit must be cleaned regularly Cut off power supply at circuit breaker fuse and wait for the unit to cool down before cleaning Use a soft rag for dusting When cleaning use only a damp rag and non N B Note that there is electrical current linked to the unit even abrasive dish soap Do not use abrasive or chemical cleaners because they if the thermostat is set off This means that there is a risk of may damage the finishing If the unit is used in a very dusty location use a electric shock as long as the unit is energized vacuum brush to remove dust and other foreign objects from the grilles Note that cigarette smoke could yellow the discharge grille and that the best way to prevent it is to clean the unit on a regular basis STAINLESS STEEL CLEANING Although stainless steel is by its very nature corrosion resistant its finish is not foolproof The key to maintaining a nice stainless steel finish is preventative cleaning Clean the metal when it is dirty do not wait until a full cleaning is required Since the acidity level and chlorine content of regular cleaning agents vary greatly it is highly recommended to thoroughly rinse the surface with clean water after clea
9. ls are more heat sensitive than others so make sure those near the unit can withstand heat Do not install on a wall behind a door DANGER High temperatures may be generated under certain abnormal conditions Do not partially or fully cover or obstruct the front of this heater Never block air vents with objects or other items You risk damaging the heater and the obstruction could lead to electric shock or overheating which could result in a fire Do not insert or allow foreign objects to enter any air vent as this may cause electric shocks fires or damages to the unit This unit has hot and arcing or sparking parts inside It is not designed to be used or stored in wet areas or areas containing flammable liquids combustible materials or corrosive abrasive chemical explosive and flammable substances such as but not limited to gasoline paint chlorine sawdust and cleaning products Some areas are dustier than others Thus it is the user s responsibility to evaluate if the unit must be cleaned based on the amount of dirt accumulated on and inside air vents Accumulated dirt can lead to a component malfunction or discoloration yellow It may cause a fire hazard if not installed and maintained in accordance with these instructions The thermal protection activation indicates that the unit has been subjected to abnormal operating conditions If the thermal protection remains activated or activates and deactivates repeatedly it is re
10. move the two 2 screws located underneath the unit and take off the front cover by pulling it gently downwards na a ain 4 Remove the wiring compartment cover 4 screws 5 Punch out one of the knock outs which allow for cable entry 6 Insert the unit into the wall opening and secure it in place by screwing four 4 screws into the four 4 holes on the outer edging of the unit 7 Make the appropriate electrical connections red to red black to black ground fault protection wire bare wire to WALL OPENING ground fault protection screw 8 Screw back into place the wiring compartment cover 9 Put the front cover back on SURFACE INSTALLATION 1 Locate the cable coming from the wall 2 Remove the control knobs thermostat knob top and timer knob bottom 3 Remove the two 2 screws located underneath the unit and take off the front cover by pulling it gently downwards 4 Remove the the wiring compartment cover 4 screws 5 Punch out one of the knock outs which allow for cable entry 6 Secure the heater to the wall by inserting screws into the holes at the very back of the heater 7 Make the appropriate electrical connections red to red black to black ground fault protection wire bare wire to ground fault protection screw 8 Screw back into place the wiring compartment cover 9 Put the front cover back on cael INSASIL20300514 OPERATION amp MAINTENANCE OPERATION Warning the heater must b
11. ning Alternatively you may use a stainless steel cleaner or clean water and dish soap Always follow polish lines DO NOT USE chlorine scrubbing pads or similar scrubbing devices steel wool abrasive cleaning agents and hydrochloric acid products such as bleach because they may stain and or damage stainless steel surfaces 4 INSASIL20300514 TROUBLESHOOTING amp REPLACEMENT COMPONENT LIST TROUBLESHOOTING NG CE O Ee SOS PROBLEM DEFECTIVE PART OR PART TO CHECK Defective thermostat timer or wrong thermostat timer setting e Open circuit breaker or fuse The thermal protection has been activated e Faulty connections The unit does not work Defective thermostat timer or wrong thermostat timer setting Tiie uaii iune continuously Heat losses higher than the unit capacity Defective thermal protection The enclosure is extremely hot e Blocked air vents e Defective motor The unit cycles under control of the thermal protection overheat e Blocked air vents indicator e Defective motor e Defective thermostat timer or wrong thermostat timer setting Overheating e Defective motor e Faulty connections Thie oreeker tipe wien fhe heelen i tuinec an Voltage higher than that written on the nameplate Elements are on but the motor does not work e Defective motor One or more elements are defective Defective thermostat timer or wrong thermostat timer setting e Voltage lower th
12. products is limited as provided above Stelpro shall not be subject to any other obligations or liabilities whatsoever whether based on contract tort or other theories of law with respect to goods or services furnished by it or any undertakings acts or omissions relating thereto Without limiting the generality of the foregoing Stelpro expressly disclaims any liability for property or personal injury damages penalties special or punitive damages damages for lost profits loss of use of equipment cost of capital cost of substitute products facilities or services shutdowns slowdowns or for other types of economic loss or for claims of a dealer s customers or any third party for such damages Stelpro specifically disclaims all consequential incidental and contingent damages whatsoever This warranty does not cover any damages or failures resulting from 1 a faulty installation or improper storage 2 an abusive or abnormal use lack of maintenance improper maintenance other than that prescribed by Stelpro or a use other than that for which the unit was designed 3 a natural disaster or an event out of Stelpro s control including but not limited to hurricanes tornadoes earthquakes terrorist attacks wars overvoltage flooding water damages etc This warranty does not cover any accidental or intentional losses or damages nor does it cover damages caused by negligence of the user or owner of the product Moreover it does not cover the
13. scribed in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Do not use outdoors RECOMMENDED HEATING CAPACITY 1 25 Wicubic foot 0 03 m It corresponds to 10 W square foot 0 09 m based on a standard ceiling height of 8 feet 2 44 m The recommended capacity is usually sufficient for normal heating needs Please note that the insulation quality of walls and windows are some of the factors that influence heat losses which modify the required capacity to heat a room If needed refer to a specialist industrial and commercial buildings who will be able to calculate these heat losses and optimize the required capacity or consult the Online heating calculation section of the Stelpro Design Web site residential buildings To heat a large room and to increase your comfort it is recommended to install several units instead of one For example 2 X 1000 W rather than 1 X 2000 W Do not install the unit where objects or pieces of furniture could be heat damaged If the unit capacity is insufficient for the size of the room it will be in operation continuously and may become defective earlier and turn yellow Respect distances and positions indicated in the installation section If the installer or the user modifies the unit he will be held responsible for any damage resulting from this modification and the CSA certification could be void This unit must not come into conta
14. the main electrical panel and contact 1 your installer or distributor 2 your service center or 3 Stelpro s customer service department In all cases you must have a copy of the invoice and provide the information written on the product nameplate Stelpro reserves the right to examine or to ask one of its representatives to examine the product itself or any part of it before honoring the warranty Stelpro reserves the right to replace the entire unit refund its purchase price or repair a defective part Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and carried out by persons authorized by Stelpro ALNVYYUVM G3LINI1 Before returning a product to Stelpro you must have a Stelpro authorization number RMA To obtain it call the customer service department at 1 800 363 3414 electricians and distributors French 1 800 343 1022 electricians and distributors English or 1 866 766 6020 consumers The authorization number must be clearly written on the parcel or it will be refused CONDITIONS EXCLUSIONS AND DISCLAIMER OF LIABILITY This warranty is exclusive and in lieu of all other representations and warranties except of title expressed or implied and Stelpro expressly disclaims and excludes any implied warranty of merchantability or implied warranty of fitness for a particular purpose gt zZ lt x a oc q a Lu m Stelpro s liability with respect to
Download Pdf Manuals
Related Search