Home

IAP-6002-WG User`s Manual

image

Contents

1. TGAP W610 W6610 Series IEEE 802 11 a b g n Access Point with Single Dual RF amp Gigabit LAN Port User Manual Version 1 2 September 2014 www oring networking com ORing Industrial Networking Corp 2 ORing TGAP W610 W6610 Series User Manual COPYRIGHT NOTICE Copyright 2014 ORing Industrial Networking Corp All rights reserved No part of this publication may be reproduced in any form without the prior written consent of ORing Industrial Networking Corp TRADEMARKS ORing is a registered trademark of ORing Industrial Networking Corp All other trademarks belong to their respective owners REGULATORY COMPLIANCE STATEMENT Product s associated with this publication complies comply with all applicable regulations Please refer to the Technical Specifications section for more details WARRANTY ORing warrants that all ORing products are free from defects in material and workmanship for a specified warranty period from the invoice date 5 years for most products ORing will repair or replace products found by ORing to be defective within this warranty period with shipment expenses apportioned by ORing and the distributor This warranty does not cover product modifications or repairs done by persons other than ORing approved personnel and this warranty does not apply to ORing products that are misused abused improperly installed or damaged by accidents Please refer to the Technical Specifications section for
2. Available values include WPAPSK WPA2PSK and WPAPSK WPA2PSK mix WPAPSK and WPA2PSK will encrypt the link without additional RADIUS server only an Auth Mode access point and client station that supports WPA PSK is required For WPA WPA2 authentication is achieved via WPA RADIUS Server You need a RADIUS or other authentication server on the network Available values include TKIP AES and TKIP AES mix WPA PSK uses TKIP encryption and WPA2 PSK uses AES Encryption Type l encryption TKIP AES provides the most reliable security and is easiest to implement Radius Server IP Enter the IP address of the RADIUS server Radius Port Enter the RADIUS port default is 1812 Shared Secret Enter the RADIUS password or key When you set security type as 802 1x the following fields will appear to allow you to configure ORing Industrial Networking Corp 27 ORing TGAP W610 W6610 Series User Manual individual settings radius key WEP Encryption You can select 64 Bit or 128 Bit Available values include ASCII and Hex Key Type ASCII American Standard Code for Information Interchange is a code for representing English characters as numbers in the Key Type range from 0 to 127 Hex digits uses 0 9 to represent values zero to nine and characters A F to represent values ten to fifteen RADIUS Remote Authentication Dial In User Service is a widely deployed protocol that enables companies to authenticate and au
3. Scan Devices Configuration Even Warning Settings 2 A Syslog Events Sy stem Status A Wizards Administrator Fie Restore Lu Group IP Setting Group Firmware Update Backup Group Configuration Backup Upgrade Group Configuration Restore Group O Ring Settin Ke P g g User Name admin Password tom af 192 168 10 2 5 3 UPnP Equipment The device supports UPnP therefore when you connect the device to the PC it will discover the presence of the device automatically To check the connection of the device to you PC follow the steps below Step 1 Go to Control Panel gt Add or Remove Programs gt Windows Components Wizard gt Networking Servers gt UPnP User Interface and pitch on the UPnP User Interface t Add or Remove Programs Windows Components Wizard d Networking Services To add or remove a component click the check box A shaded box means that only part of the component will be installed To see what s included in a component click Details Subcomponents of Networking Services Ei Intemet Gateway Device Discovery and Control Client 0 0 MB O a Feerto Peer CO Bop Listener C ni p A UPnP User Interface A Description Alws you to find and control Intemet connection sharing hardware and software that uses UPnP TM sd Total disk space required 0 0 ME NW Space available on disk 6718 7 MB ORing Industrial Networking Corp 17 ORing TGAP W610 W6610 Series Us
4. Management a 16 5 1 N NOR Eeer ee seraa ee ere 16 Dic Open Vision Configuration sisi 16 5 3 CPR EGODE I et a a 17 5 4 Web Browser Management 18 5 5 KEE 19 Sol OVVIO EE 19 532A SIC OO AO ee 20 SE Wireless e nes ss nca gens nee caen ssnse nee sense cames ntesrese 23 5 5 4 Advanced Setting ccccccccececcecesceccceeecceeecceeccceeesceeesceeesceeesceeesceeesceeesoeeess 36 999 Event Warning SONOS recat elated a ce mo men 37 556 EE 40 5 5 7 Administrator sisi 41 Technical Specifications cccscccceeseeseeseeceneeeeesseseeseesenseesenseesenseesensesees 44 ORing Industrial Networking Corp 2 ORing TGAP W610 W6610 Series User Manual Belle UE e E 46 ORing Industrial Networking Corp 3 ORing TGAP W610 W6610 Series User Manual Getting Started 1 1 About the TGAP W610 6610 Series The TGAP W610 W6610 series are reliable outdoor WLAN access points with one TGAP W610 series or dual TGAP W6610 series 802 11 a b g n wireless l modules The series consists of four models I TGAP W610 TGAP W6610 TGAP W610 M12 and ill TGAP W6610 M12 The first two models feature a A WU i Gigabit LAN port in RJ45 connector and the last two models feature a Gigabit LAN port in M12 connector type J With EN50155 compliance and M12 connectors the devices can ensure tight and robust connections achieving reliable operations against environmental disturbances such as vibration and shock and are
5. a value from 1 to 65535 Web Access Control You can choose to access the web page via wired or wireless connections DHCP Server Enables or disables the DHCP server function When enabled the device will become the DHCP server on your local network Start IP Address The starting IP address of the IP range assigned by the DHCP server The start IP address is usually the lowest figures For example in a dynamic IP range from 192 168 1 100 to 192 168 1 200 192 168 1 100 will be the start IP address Maximum Number of You can specify the number of IPs allowed to access the device IPs For example if the dynamic IP range is from 192 168 1 100 to 192 168 1 200 you should enter 100 in this box Lease Time Hour The period of time for an IP address to be leased During the lease time the DHCP server cannot assign that IP address to any other clients Once the lease time ends the system will reassign the IP address Time Setting In this page you can set the date amp time of the device A correct date and time will help the system log events You can set up a NTP Network Time Protocol client to synchronize date amp time to a NTP server on the Internet ORing Industrial Networking Corp 22 ORing TGAP W610 W6610 Series User Manual Get Current Date amp Time from Browser Get Current Date amp Click to set the time from your browser Time from Browser 5 5 3 Wireless Setting This section allows you to co
6. authority to operate the equipment This device should be operated with minimum distance 20cm between the device and all persons Operations in the 5 15 5 25GHz band are restricted to indoor usage only Industry Canada Statement This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Industry Canada Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of Industry Canada Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe B prescrites dans la norme sur le mat rial brouilleur Appareils Num riques NMB 003 dict e par l Industrie ORing Industrial Networking Corp 46 ORing TGAP
7. back of the device using four screws The plate can be attached vertically or horizontally to the device based on the space available ORing Industrial Networking Corp 11 ORing TGAP W610 W6610 Series User Manual Vertical Step 2 Thread the two supplied metal mounting straps through the large slots on the mounting plate and then put the straps around the pole ORing Industrial Networking Corp 12 ORing TGAP W610 W6610 Series User Manual 3 3 Wiring For pin assignments of the power connector please refer to the following tables 3 3 1 Grounding Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI Run the ground connection from the grounding pin on the power connector to the grounding surface prior to connecting devices 3 3 2 Power Port Pinouts The device supports two sets of power supplies and uses the M12 5 pin female connector on the front panel for the dual power inputs Step 1 insert the negative positive wires into the V V terminals respectively Step 2 to keep the DC wires from pulling loose use a small flat blade screwdriver to tighten the wire clamp screws on the front of the terminal block connector Vie V2 Vi v2 ORing Industrial Networking Corp 13 ORing TGAP W610 W6610 Series User Manual Cables and Antenna 4 1 Ethernet Pin Definition The series provides one 10 100 1000 Base T X Ethernet port in either M12 TGAP W610 W661
8. communications TGAP W6610 only Support external N Type antenna installation 1KV isolation for PoE P D IIP 67 waterproof housing Operating temperature 25 to 70 C Storage temperature 40 to 85 C Operating humidity 5 to 95 non condensing Dimensions 310 W x 310 D x 87 H 12 2 x 12 2 x 3 4 inch ORing Industrial Networking Corp 5 ORing TGAP W610 W6610 Series User Manual Hardware Overview 2 1 Bottom Panel 2 1 1 Ports and Connectors The devices are equipped with the following ports and features on the bottom panel 10 100 1000Base T X 1 x 10 100 1000 Base T X port supporting auto negotiation Ethernet port TGAP W610 TGAP W6610 M12 using M12 connector TGAP W610 TGAP W6610 using RJ45 connectors M12 power connector Dual power inputs for 12 48 VDC with dual power inputs Reset button To restore the device configurations back to the factory defaults press the Reset button for a few seconds Once the power indicator starts to flash release the button The device will then reboot and return to factory defaults Antenna connector 1 x N type female antenna connector on the top panel of TGAP W610 M12 1 x N type female antenna connectors on both the top and bottom panels of TGAP W6610 M12 TGAP W610 M12 ORing Industrial Networking Corp 6 ORing TGAP W610 W6610 Series User Manual WE Power Ni 1248700 10 1 234 567 g 9 10 TGAP W6610 M12 TGAP W6610 LED for WLA
9. or 128 wired and wireless network devices which are connected to their respective Ethernet ports to limit the amount of forwarded data Only data destined for stations which are known to reside on the peer Ethernet link multicast data or data with unknown destinations need to be forwarded to the peer AP via the WDS link The peer WDS APs are based on the MAC addresses listed in Peer Mac Address q WW BS a Bear in mind the following principles when setting the WDS mode to bridge mode sch LAN IP address should use a different IP in the same network Shut down all DHCP server functions of the AP Enable WDS Each AP should have the same setting except Peer Mac Address should be set to the N other s Mac address O1 The settings of security and channel must be the same 6 The distance of the AP should be limited within a certainty area Set WDS as Repeater Mode In this mode repeater is used to extend the range of the wireless infrastructure by forwarding traffic between associated wireless stations and another repeater or AP connected to the wired LAN The peer WDS APs are based on the MAC addresses listed in Peer Mac Address ORing Industrial Networking Corp 33 ORing TGAP W610 W6610 Series User Manual Wireless Options a a ah MENE A EK Kees be lt Bo Radio Button Enables or disables wireless functions Beacon Interval A beacon is a packet sent by a wireless acce
10. points in your wireless network support short preamble then enabling it can boost overall throughput However if any wireless device does not support short preamble then it will not be able to communicate with your network If you are not sure whether your radio supports the short RF preamble you must disable this feature Preamble The value specifies the maximum size for a packet before data is fragmented into multiple packets The value should remain at the default 2346 the range is 256 2346 bytes If you experience a high packet error rate you may slightly increase the value Setting the value too low may result in poor network performance Only minor modifications of this value are recommended Roaming Select Disabled to disable X Roaming protocol or select X roaming to enable X Roaming protocol ORing Industrial Networking Corp 35 ORing TGAP W610 W6610 Series User Manual Select All to scan all supported channels or Manual to scan only selected channels specified in Channel Select Channel Select Assign the value roaming channels Sensitivity Configures signal sensitivity Scan interval Configures scan interval 5 5 4 Advanced Setting Filters This page allows you to set up MAC filters to allow or deny wireless clients to connect to the AP You can manually add a MAC address or select a MAC address from the Associated Clients list currently associated with the AP MAC Filter Select Enabled or Disabled to act
11. toute autre antenne ou transmetteur ORing Industrial Networking Corp 47
12. 0 M12 or RJ45 TGAP W610 W6610 connector type According to the link type the AP uses CAT 3 4 5 5e UTP cables to connect to any other network device PCs servers switches routers or hubs Please refer to the following table for cable specifications 10Base T Cat 3 4 5 100 ohm UTP 100 m 828 ft RJ45 M12 100Base I X Cat 5 100 ohm UTP UTP 100 m 328 ft RJ45 M12 1000BASE T Cat 5 Cat 5e 100 ohm UTP UTP 100 m 328 ft RJ45 M12 BI DB BI DA BI_DC ER WE KE BI_DB RJ45 Connector 4 2 Wireless Antenna The AP comes with two four WiFi antennas with N type female connectors You can also use external RF cables and antennas with the connectors ORing Industrial Networking Corp 14 ORing TGAP W610 W6610 Series User Manual e nu qe ae 18 Remember to use the 2 4GHz antennas when the device operates in IEEE 802 11b g and the 5GHz antennas when operating in IEEE802 11a The antennas must be installed within a safety area which is covered by a lightning protection or surge arrest system ORing Industrial Networking Corp 15 ORing TGAP W610 W6610 Series User Manual Management 5 1 Network Connection Before installing the device you need to be able to access the device via a computer equipped with an Ethernet card or wireless LAN interface To simplify the connection it is recommended to use an Ethernet card to connect to a LAN e e Pi Te Ce cs di d i A i i
13. 10 2 default gateway IP of the device in the address box to access the webpage A login window will pop up where you can enter the default login name admin and password admin For security reasons we ORing Industrial Networking Corp 18 ORing TGAP W610 W6610 Series User Manual strongly recommend you to change the password Click on Administrator gt Password after logging in to change the password IC Login Windows Internet Explorer IO we ao 192 168 10 2 Si B Li earth q Pi BAD WE MAO ANAEW IAM NAW p 2 ore 5 5 Configurations The Home screen will appear with a short description of the device You can lick Run Wizard on the page for quick configurations of a new password wireless SSID and channel and encryption Industrial EN50155 IEEE 802 11 a b g n AP with 1x10 100 1000Base T X PoE ORing P D IP 67 grade EU Band 5 5 1 Overview This setting will show the general information with regard to the device including system information LAN network information and wireless network information System Info ORing Industrial Networking Corp 19 ORing TGAP W610 W6610 Series User Manual LAN Info Wireless Info 5 5 2 Basic Setting This section will allow you to configure the general settings for the device System Info Setting TGAP WE10 M12 CC wein MI 12 00 ORing Industrial Networking Corp 20 ORing TGAP W610 W6610 Series User Manual LAN
14. 28 Bit can select 64 Bit or 128 Bit Available values include ASCII and Hex Key Type ASCII American Standard Code for Information Interchange is a Key Type code for representing English characters as numbers in the range from 0 to 127 Hex digits uses 0 9 to represent values zero to nine and characters A F to represent values ten to fifteen Default Key Index Select one of the keys to be the active key Key 1 to 4 You can input up to four encryption keys When you set security type as WPA WPA2 Personal the following fields will appear to allow you to configure individual settings WPAAVPA2 Personal ff e Available values include WPAPSK WPA2PSK and Auth Mode WPAPSK WPA2PSK mix WPAPSK and WPA2PSK will ORing Industrial Networking Corp 26 ORing TGAP W610 W6610 Series User Manual encrypt the link without additional RADIUS server only an access point and client station that supports WPA PSK is required For WPA WPA2 authentication is achieved via WPA RADIUS Server You need a RADIUS or other authentication server on the network Available values include TKIP AES and TKIP AES mix WPA PSK uses TKIP encryption and WPA2 PSK uses AES Encryption Type encryption TKIP AES provides the most reliable security and is easiest to implement When you set security type as WPA WPA2 Enterprise the following screen will appear to allow you to configure individual settings WPAMWPA2 Enterprise M radius key
15. M with BPSK QPSK QAM 64QAM i IEEE802 11b CCK DQPSK DBPSK Modulation l IEEE802 11g OFDM with BPSK QPSK 16QAM 64QAM IEEE802 11n BPSK QPSK 16 QAM 64 QAM America FCC 2 412 2 462 GHz 11 channels 5 180 5 240 GHz amp 5 745 5 825 GHz 9 channels Europe CE ETSI 2 412 2 472 Ghz 13 channels 5 180 5 240 GHz 4 channels IEEE802 11b 1 2 5 5 11 Mbps Transmission Rate IEEE802 11a g 6 9 12 18 24 36 48 54 Mbps IEEE801 11n up to 300Mbps Lila 12dBm 1 5dBm 11b 17dBm 1 5dBm 11g 15dBm 1 5dBm Transmit Power Lion HT20 13dBm 1 5dBm 150Mbps 1ign HT40 12dBm 1 5dBm 300Mbps iian HT20 12dBm 1 5dBm 150Mbps iian HT40 12dBm 1 5dBm 300Mbps 802 11a 68dBm 2dBm 54Mbps 802 11b 85dBm 2dBm 11Mbps 802 11g 68dBm 2dBm 54Mbps Receiver Sensitivity 802 11gn HT20 68dBm 2dBm 150Mbps 802 11gn HT40 68dBm 2dBm 300Mbps 802 11an HT20 68dBm 2dBm 150Mbps 802 11an HT40 68dBm 2dBm 300Mbps WEP 64 bit 128 bit key supported WPA WPA2 802 11i WEP and AES encryption Encryption Security WPAPSK 256 bit key pre shared key supported 802 1X Authentication supported TKIP encryption Wireless Security SSID broadcast disable and enable Protocol Support ARP BOOTP DHCP DNS HTTP IP ICMP SNTP TCP UDP RADIUS SNMP STP RSTP LED indicators Over load amp short circuit protection Isolation Voltage 1000 VDC min Isolation Resistance 108 ohms min Frequency Band Power indica
16. N1 connection LED for LAN port connection 1 Power connector LED for PWR1 status LED for PW2 status LED for PoE status LED for WLAN2 connection Reset button LAN port 0 Connector for WiFi2 antenna ae Se Je 2 O pp Np ORing Industrial Networking Corp 7 ORing TGAP W610 W6610 Series User Manual 2 1 2 Bottom Panel LEDs 1 egen Status reene pur Pure roe Om On Power suppied over Enemet cabe Port is linked Green Blinking Transmitting data ETH WLAN activated WLAN Green Blinking Transmitting data via WLAN 2 2 Top Panel 1 Antenna connectors ORing Industrial Networking Corp 8 ORing TGAP W610 W6610 Series User Manual Mardware Installation Before installing the device make sure you have all of the package contents available and a PC with Microsoft Internet Explorer 6 0 or later for using web based system management tools When installed outdoors make sure the connectors on the panel are facing down to prevent water intrusion Do not remove the water proof casing and avoid touching or moving the device when the antennas are transmitting or receiving When installing the device make sure to keep the radiating at a minimum distance of 20 cm 7 9 inches from all persons to minimize the potential for human contact during normal operation Do not operate the device near unshielded blasting caps or in an otherwise explosive environment unless the device has been modified for suc
17. Setting This page allows you to configure the IP settings of the LAN port for the device 192 168 10 9 255 255 255 0 DU A D 0 Apply Cancel Obtain an IP address Select this option if you want the IP address to be assigned automatically automatically by the DHCP server in your network Use the following IP Select this option if you want to assign an IP address to the address device manually You should set up IP address subnet mask and default gateway for the device IP Address The device comes with default IP address but you can also input a new IP address Subnet Mask 255 255 255 0 is the default value All devices on the network must have the same subnet mask to communicate on the network ORing Industrial Networking Corp 21 ORing TGAP W610 W6610 Series User Manual Default Gateway Enter the IP address of the device in your network Obtain DNS server Obtains a DNS server address from a DHCP server If you have address chosen to obtain an IP address automatically this option will be automatically selected accordingly Use the following 8 Specifies a DNS server address manually You can enter two DNS server addresses as the primary and secondary options addresses Web Protocol Choose a Web protocol for the device The default value is HTTP For higher security choose HTTPS SES Each Web protocol has a default port HTTP is 80 and HTTPS is 443 You can also enter
18. W610 W6610 Series User Manual Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device L op ration est soumise aux deux conditions suivantes 1 cet appareil ne peut causer d interf rences et 2 cet appareil doit accepter toute interf rence y compris celles susceptibles de provoquer fonctionnement du dispositif To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication Afin de r duire les interf rences radio potentielles pour les autres utilisateurs le type d antenne et son gain doivent tre choisie que la puissance isotrope rayonn e quivalente PIRE est pas plus que celle premise pour une communication r ussie RF exposure warning The equipment complies with RF exposure limits set forth for an uncontrolled environment The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter Avertissement d exposition RF L quipement est conforme aux limites d exposition aux RF tablies pour un incontr l s environnement L antenne s utilis e pour ce transmetteur ne doit pas tre co localis s ou fonctionner en conjonction avec
19. er Manual Step 2 At the right below corner of the computer you will find an UPnP icon of the device i TGaP W610 M12 new device is now available on your network For more information click here Step 3 Click on the icon and you will find the UPnP device in My Network Places T My Network Places File Edit view Favorites Tools Help T gt IS Search gt Folders HAE Address oJ My Network Places Local Network TOGAF Wei MI A Network Tasks Add a network place Ki View network connections Set up home or small office network DU a Step 4 Right click the UPnP device and choose Properties to view detailed information of the device Step 5 Double click the device icon will lead you to the management web page 5 4 Web Browser Management An embedded HTML web site resides in the flash memory of the device It contains advanced management features which you can manage from anywhere on the network through a standard web browser such as Microsoft Internet Explorer Internet Explorer 5 0 or later versions It is based on Java Applets which can reduce network bandwidth consumption enhance access speed and provide user friendly viewing windows Note By default IE5 0 or later version does not allow Java Applets to open sockets You need to explicitly modify browser settings in order to enable Java Applets to use network ports Open a web browser on your computer and type http 192 168
20. et Cold Start Software Reset Warm Start Login Failed IP Address Changed Password Changed Redundant Power Changed Eth Link Status Changed SNMP Access Failed Wireless Client Associated Wireless Client Disassociated Client Mode Associated Client Mode Disassociated Client Mode Roaming Fault Event Notification Power 1 Fault Power Fault Eth1 Link Down SMTP Server Enter a backup host to be used when the primary host is unavailable Server Port Specifies the port where MTA can be contacted via SMTP server E mail Address 1 4 Enter the mail address that will receive notifications ORing Industrial Networking Corp 38 ORing TGAP W610 W6610 Series User Manual SNMP E Device Event Notification Hardware Reset Cold Start Software Reset Warm Start Login Failed IP Address Changed Password Changed Redundant Power Changed Eth Link Status Changed SNMP Access Failed Wireless Client Associated Wireless Client Disassociated Client Mode Associated Client Mode Disassociated Client Mode Roaming Fault Event Notification Power 1 Fault Power 2 Fault Ethi Link Down Label Description SNMP Agent SNMP Simple Network Management Protocol Agent is a service program that runs on the access point The agent provides management information to the NMS by keeping track of various operational aspects of the AP system You can enable or disable the function ORing Industrial Ne
21. h use by qualified personnel The device can be fixed to a pole or the wall using the supplied mounting plate Make sure the connectors on the bottom panel are facing down when installing to prevent water intrusion Screw holes for attaching the plate to the unit K NN Wall mount 7 screw holes Strap slots for pole mounting Mounting plate ORing Industrial Networking Corp 9 ORing TGAP W610 W6610 Series User Manual 3 1 Wall Mounting Dimension Unit mm Wall mount Measurements All Models Follow the steps below to install the device to the wall Step 1 Attach the mounting plate to the back of the device using four screws The plate can be attached vertically or horizontally to the device based on the space available Vertical ORing Industrial Networking Corp 10 ORing TGAP W610 W6610 Series User Manual Horizontal Step 2 Hold the device upright against the wall Step 3 Insert four screws through the large opening of the keyhole shaped apertures at the top and bottom of the plate and fasten the screw to the wall with a screwdriver Instead of screwing the screws in all the way it is advised to leave a space of about 2mm to allow room for sliding the device between the wall and the screws 3 2 Pole Mounting You can mount the device to a pole using adjustable steel band straps included in the kit When installing the device to a pole Step 1 Attach the mounting plate to the
22. hannel to be used Channel 6 is the default channel You can also select a new number from the dropdown list All devices on Channel the network must be set to the same channel to communicate on the network Wireless channel must be the same as the other device in the group A WDS master is the central control point for authenticating wireless clients caching client key material distributing MFP key material WDS Master D reporting radio management information to an upstream network ode management station and updating other APs participating in WDS You can set the device as the WDS master by selecting from the list You can choose the security type for your WLAN connection from the following options None no encryption WEP WEP Wired Equivalent Privacy is a wireless security protocol Security options for WLAN WEP will encrypt data transmitted on the WLAN WPA WPA2 Personal uses a pre shared key for authentication This pre shared key is then dynamically sent between the AP and clients Each authorized computer is given the same pass phrase Peer AP SSID Enter the SSID of the AP you want to connect as a client Peer AP BSSID Enter the BSSID Wireless MAC address to limit client target Slave Mode Enables or disables slave mode You can scan APs on the network using this mode Security Type Select the security type used by the client you want to connect Client Mode In this mode the AP functions as a wireless cl
23. ideal for rolling stock applications The APs come with an IP 67 waterproof housing to protect them from damage in harsh weather when installed outdoors Featuring two or four N Type connectors that can house any N Type antennas for extended communications distances the devices are ideal for the toughest industrial environments In addition the LAN port of the devices is PoE enabled allowing the device to be powered over the existing network cable The APs can be configured to operate in AP Client Bridge AP Client modes and support MAC filters for security control The devices can be configured and managed via a Window utility or Web interface on LAN or WLAN networks 1 2 Software Features WR High speed air connectivity with support up to 300Mbps m Highly secure transmission with WEP WPA WPA PSK TKIP AES WPA2 WPA2 PSK TKIP AES 802 1X Authentication supported Support Long Distance Air Connectivity Support Multi SSID Support X Roaming lt 60 ms Support wireless load balance Supports AP Client Bridge AP Client modes Support MAC IP Port Filter Wireless connecting status monitoring Secured Management by HTTPS Event warning via Syslog e mail SNMP traps and relay ORing Industrial Networking Corp 4 ORing TGAP W610 W6610 Series User Manual 1 3 Hardware Features WR 1x 10 100 1000 Base T X Ethernet port in RJ45 TGAP W610 and TGAP W6610 or M12 connector type TGAP W610 M12 and TGAP W6610 M12 Dual RF for redundant wireless
24. ient to connect your wired devices to a wireless network This mode provides no access point services but supports 802 1X ORing Industrial Networking Corp 30 ORing TGAP W610 W6610 Series User Manual Hidden Show SiteT able Disabled M WEP WPAWPA2 Personal 802 1X apply WPA WPA2 Enterprise Enter the BSSID Wireless MAC address to limit client target She Scan Enabesordisabessavemode Select the security type used by the client you want to connect Bridge Mode Select this option if the device is connected to a local network downstream from another router In this mode the device functions as a bridge between the network on its WAN port and the devices on its LAN port and those connected to it wirelessly Bridge v Bridge Mode y Bridge Mode Repeater Mode Apply ke Cancel ORing Industrial Networking Corp 31 ORing TGAP W610 W6610 Series User Manual This type of wireless link is established between two IEEE 802 11 access points Wireless packets transmitted along the WDS link comply with the IEEE 802 11 WDS Wireless Distribution System format at the link layer This mode provides static LAN to LAN bridging functionality which is supported through WDS WDS enables access points or routers to be wirelessly connected to one another This function is usually used in large open areas such as warehouses where wiring is restricted or costly and in some larger home e
25. ivate or deactivate MAC filters Select one of the options to allow or deny the MAC address in the list Associated Clients Shows the wireless MAC addresses associated with the device MAC Filter Table You can edit up to MAC addresses in these fields Apply Click to activate the configurations ORing Industrial Networking Corp 36 ORing TGAP W610 W6610 Series User Manual Misc Settings 5 5 5 Event Warning Settings When an error occurs the device will notify you through system log e mail SNMP and relay You can choose the system to issue a notification when specific events occur by checking the box next to the event System Log Device Event Notification Hardware Reset Cold Start Software Reset Warm Start Login Failed IP Address Changed Password Changed Redundant Power Changed Eth Link Status Changed SNMP Access Failed Wireless Client Associated Wireless Client Disassociated Client Mode Associated Client Mode Disassociated Client Mode Roaming Fault Event Notification Power 1 Fault Power Fault Ethi Link Down ORing Industrial Networking Corp 37 ORing TGAP W610 W6610 Series User Manual Syslog Server IP Enter the IP address of a remote server if you want the logs to be stored remotely Leave it blank will disable remote syslog Syslog Server Port Specifies the port to be logged remotely Default port is 514 E Mail Device Event Notification Hardware Res
26. nfigure the wireless settings of the device when operating in different modes ORing Industrial Networking Corp 23 ORing TGAP W610 W6610 Series User Manual AP M AF Client Client Bridge 1 w orin 5 K Disabled w Disabled ze None k Appl DAVE Cancel AP Mode You can set the device to work in AP mode This is the most common mode for all wireless APs In this mode the AP will act as a central connection point which other wireless clients can connect to AP oring e Disabled v None Mone WPAAVPA Personal WPAAVPA Enterprise 002 1 Multiple SSID index The index of the SSID SSID SSID Service Set Identifier is a unique name that identifies a ORing Industrial Networking Corp 24 ORing Channel WDS Master Mode AP Isolation Security options TGAP W610 W6610 Series User Manual network All devices on the network must be set with the same SSID in order to communicate with each other Fill in a new SSID in this field if you do not want to use the default value Specify a channel to be used Channel 6 is the default channel You can also select a new number from the dropdown list All devices on the network must be set to use the same channel to communicate on the network A WDS master is the central control point for authenticating wireless clients caching client key material distributing MFP key material reporting radio management information to an up
27. nternet 4 L is H Follow the steps below to install and connect the device to PCs Connect a computer to the device Use either a straight through Ethernet cable or cross over cable to connect the LAN port of the device to a computer Once the LED of the LAN port lights up which indicates the connection is established the computer will initiate a DHCP request to retrieve an IP address from the AP 5 2 Open Vision Configuration The device can be configured using ORing s proprietary Windows utility Open Vision Follow the steps below to set up the device in Open Vision Step 1 Open the commander and click Discover a list of AP devices will be shown Step 2 Choose your access point The functions of the AP will be shown in a tree structure Step 3 Type in the username and password to log in to setup the AP ORing Industrial Networking Corp 16 ORing TGAP W610 W6610 Series User Manual Commander Sel Task Settings Help Gi gi J Discovery Discovery Filter Login all Logout al Auto Logout Reboot Open web Refresh ClearState RefreshAll Group IP Wizard Group Firmware Wizard Group l Sort Devices By Model D All Functions 1 192 168 10 2 00 44 BB CC DB 10 Commander D 1 Operation Mode AP FE Devices DI Geier Ss Signal Strength 0 a TGAP W610 M12 a cs Encryption No encryption H TGAP W610 M12 192 168 a pe bei SSID oring Status Monitor SE AP Client Client Connection Info
28. nvironments Peer MAC Address Enter the Mac address of other access point s and check the Enable box SSID Service Set Identifier is a unique name that identifies a SSID only Repeater network All devices on the network must be set with the same SSID mode support in order to communicate with each other Fill in a new SSID in this field if you do not want to use the default value Specify a channel to be used Channel 6 is the default channel You can also select a new number from the dropdown list All devices on Channel the network must be set to the same channel to communicate on the network Wireless channel must be the same as the other device in the group You can choose the security type for your WLAN connection from the following options None no encryption Security options WEP WEP Wired Equivalent Privacy is a wireless security protocol for WLAN WEP will encrypt data transmitted on the WLAN WPA WPA2 Personal uses a pre shared key for authentication ORing Industrial Networking Corp 32 ORing TGAP W610 W6610 Series User Manual This pre shared key is then dynamically sent between the AP and clients Each authorized computer is given the same pass phrase Set WDS as Bridge Mode In the mode the AP acts as a standard bridge that forwards traffic between WDS links links connected to other AP wireless bridges and an Ethernet port As a standard bridge the AP learns MAC addresses of up to 64 wireless
29. rmware download new firmware from ORing s website to your PC and install it via Web upgrade Make sure the firmware file matches the model of your device It will take several ORing Industrial Networking Corp 42 ORing TGAP W610 W6610 Series User Manual minutes to upload and update the firmware After upgrade completes successfully reboot the device During firmware upgrading do not turn off the power of the device or press the reset button Load Factory Default You can use this page to restore the device to factory default settings Make sure to save the device settings before clicking on this button All current settings will be lost after you click this button Restore Default Settings Restart Click the button in this page to restart the device through warm reset ORing Industrial Networking Corp 43 ORing TGAP W610 W6610 Series User Manual Technical Specifications ORing WLAN Access Point Model TGAP W6610 M12 TGAP W610 M12 Physical Ports 10 100 1000Base T X p S RJ45 or M12 8 pin A coding x 1 Auto MDI MDIX Present at ETH PoE P D port Fully compliant with IEEE 802 3af Power Device specification WLAN interface Operating Mode Dual AP Dual Client Bridge AP Client Mode P Dual Client Bridge AP Client Mode 4 x External N Type female antenna Antenna Connector 2 x External N Type female antenna connector connector Radio Frequency Type DSSS OFDM IEEE802 11a OFD
30. ss point to synchronize wireless devices The beacon interval value indicates the frequency interval of the beacon Increasing the beacon interval reduces the number of beacons and the overhead associated with them The default value is 100 but 50 is recommended when reception is poor DTIM Interval The value specifies the maximum size for a packet before data is fragmented into multiple packets The value should remain at the default 2346 the range is 256 2346 bytes If you experience a high packet error rate you may slightly increase the value Setting the ORing Industrial Networking Corp 34 ORing TGAP W610 W6610 Series User Manual value too low may result in poor network performance Only minor ae Fragmentation The RTS Request to Send threshold is the amount of time a Threshold wireless device that attempts to send will wait for a recipient to acknowledge that it is ready Normally the AP sends a RTS frame to a station and negotiates the sending of data After receiving the RTS the station responds with a CTS Clear to Send frame to acknowledge the right to begin transmission To ensure communication the maximum value should be used which is the default value 2347 the range is 0 2347 bytes If a network packet is smaller than the preset RTS threshold size the RTS CTS mechanism will not be enabled Wireless Network Available values include Long and Short with Long as the default value If all clients and access
31. stream network management station and updating other APs participating in WDS You can set the device as the WDS master by selecting from the list This function prevents devices connected to an AP from communicating directly with each other This function is useful when many wireless clients request your network frequently You can choose the security type for your WLAN connection from the following options None no encryption WEP WEP Wired Equivalent Privacy is a wireless security protocol for WLAN WEP will encrypt data transmitted on the WLAN WPA WPA2 Personal uses a pre shared key for authentication This pre shared key is then dynamically sent between the AP and clients Each authorized computer is given the same pass phrase WPA WPA2 Enterprise this type includes all of the features of WPA WPA2 Personal plus support for 802 1x RADIUS authentication 802 1x authentication through a RADIUS server When you set security tyoe as WEP the following fields will appear to allow you to configure individual settings ORing Industrial Networking Corp 25 ORing TGAP W610 W6610 Series User Manual Available values include ea Shared and WEPAUTO When choosing Open or Shared all of the clients must select the Auth Mode same authentication to associate this AP If select WEPAUTO the clients do not have to use the same Open or Shared authentication mui SE can choose any one to authenticate You can select 64 Bit or 1
32. the actual warranty period s of the product s associated with this publication DISCLAIMER Information in this publication is intended to be accurate ORing shall not be responsible for its use or infringements on third parties as a result of its use There may occasionally be unintentional errors on this publication ORing reserves the right to revise the contents of this publication without notice CONTACT INFORMATION ORing Industrial Networking Corp 3F No 542 2 Zhongzheng Rd Xindian Dist New Taipei City 23148 Taiwan R O C Tel 886 2 2218 1066 Fax 886 2 2218 1014 Website www oring networking com Technical Support E mail support oring networking com Sales Contact E mail sales oring networking com Headquarters sales oring networking com cn China ORing Industrial Networking Corp 1 ORing TGAP W610 6610 Series User Manual Table of Content Gening ES Le Cie PR 4 1 1 About the TGAP W610 6610 Series 4 1 2 DO INATE FE ET 4 1 3 Hardware Features 5 Hardware OVNI ess Ea SA SEREN EEE 6 2 1 BOLOM PANO EE 6 Peel PONS ana CONE CTO oaa A A E EE EE 6 Bela BOHOM ale RE 8 2 2 TOD O A nt 8 3 1 VA e Caia o E E E A nine 10 3 2 FOC NN ETON Le D 11 3 3 VAO ctosecdresstensaatiosetesasonebacdinss tonssauduasahnsshwsate sedan ay tuseiunree areata vivanieutetunaenacas 13 SSC MC deine Le ii 13 33 2 FPOWGE POM PINGUIS E 13 Caples ANG BT E 14 4 1 Ethernet Pin Definition sn 14 4 2 Wireless Antenn 14
33. thorize remote users access to a system or service from a central network server When you configure the remote access server for RADIUS authentication the credentials of the connection request are passed to the RADIUS server for authentication and authorization After the request is both authenticated and authorized the RADIUS server sends an accept message back to the remote access server and the connection attempt is accepted Otherwise the RADIUS server sends a reject message back to the remote access server and the connection attempt is rejected Connection of Radius server is shown as follows ORing Industrial Networking Corp 28 ORing TGAP W610 W6610 Series User Manual Users Database Wireless Computer Validate RADIUS Server 8 Wired Computer AP Client Mode This mode provides a one to many MAC address mapping mechanism such that multiple stations behind the AP can transparently connect to the other AP even if they don t support WDS LA oring Dites None Hidden Show SiteTable a Disabled None DR Save St ORing Industrial Networking Corp 29 ORing TGAP W610 W6610 Series User Manual Le eme S SSID Service Set Identifier is a unique name that identifies a network All devices on the network must be set with the same SSID in order to communicate with each other Fill in a new SSID in this field if you do not want to use the default value Specify a c
34. tor 2 x LEDs PW1 PW2 PoE Green On Power is on and booting up 10 100 1000Base T X D s 1 x LEDs Green for port Link Act indicator WLAN LED 2 x LEDs Green for WLAN Link Act 1 x LEDs Green for WLAN Link Act Power Input power Dual Power Inputs 12 48 VDC with M12 connector ORing Industrial Networking Corp 44 ORing TGAP W610 W6610 Series User Manual Physical Characteristic Environmental 40 to 85 C 40 to 185 F 5 to 95 Non condensing Regulatory approvals EN61000 4 2 ESD EN61000 4 3 RS EN61000 4 4 EFT EN61000 4 5 Surge EN61000 4 6 CS FCC Part 15 CISPR EN55022 class A EN50155 EN50121 3 2 EMS EN61000 4 8 EN61000 4 11 Warranty 5 years ORing Industrial Networking Corp 45 ORing TGAP W610 W6610 Series User Manual Compliance FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation RF exposure warning The equipment complies with RF exposure limits set forth for an uncontrolled environment The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your
35. tworking Corp 39 ORing TGAP W610 W6610 Series User Manual SNMP Trap Server Enter the IP address of the SNMP server which will send out traps Community Community is a password to establish trust between managers an and agents Normally public is used for read write community SysLocation Specifies sysLocation string SysContact Specifies sysContact string Relay This page allows you to enable faulty relay function for the device by check the individual boxes Fault LED Relay Power 1 Fault Power 2 Fault Ethi Link Down 5 5 6 System status Wireless Link List This page displays the information of the wireless clients connected to the device including their MAC address data rate and link types Mac Address Rx Bytes Rx Packets Tx Bytes Tx Packets Rssi Quality Tx Bitrate Link Type DHCP Clients List This page lists the devices on your network that are receiving dynamic IP addresses from the device Hostname Mac Address IP Address Expires In Traffic Port Status This page displays the network traffic statistics for both received and transmitted packets ORing Industrial Networking Corp 40 ORing TGAP W610 W6610 Series User Manual through the Ethernet port and wireless connections associated with the AP Note that the traffic counter will reset when the device is rebooted Interface Receive System Log The device will constantly log events and activities in System Log and provide the file for yo
36. u to review You can click Refresh to renew the page or Clear to clear all or certain log entries Date Time Content 5 5 7 Administrator Setting Password This page allows you to change the username and password You must type in the new password twice to confirm the default username and password are admin ORing Industrial Networking Corp 41 ORing TGAP W610 W6610 Series User Manual Old Name Type in current login name Old Password Type in current password Enter a new login name Acceptable characters contain 0 9 a z A Z and the length must be 1 to 15 characters An empty name is not acceptable New Password Enter a new login password Acceptable characters contain hia 0 9 a z A Z and the length must be 0 to 15 characters Saving Configurations This page allows you to save existing configurations as a backup file or return the device to previous settings Click to save the current system settings as a file stored in the Download local hard drive Upload You can restore configurations to previous status by installing a previous configuration file To do this click on Browse to locate the file you want to upload in the local hard drive and click Upload Restore Default Click to reset the device to the factory settings The device will Settings reboot to validate the default settings Firmware Upgrade ORing launches new firmware constantly to enhance performance and functions To upgrade fi

Download Pdf Manuals

image

Related Search

Related Contents

Craftsman 52-Inch Service Parts  2.2 Mo - Conseil général de la Creuse  securityProbe User Manual - NETWAYS-Online  

Copyright © All rights reserved.
Failed to retrieve file