VPW-280755 Manual - VANCO International
Contents
1. Vanco International 506 Kingsland Drive Batavia Illinois 60510 Call 888 769 4156 fax 630 879 9189 visit www vanco1 com2. Setting the DIP switch to this position will instruct the matrix to use embedded 1080p 3D video and Stereo audio to encourage communication between the matrix and 3D sources 3D displays if handshake problems are encountered After setting the DIP switch reconnect and turn on for the changes to take effect RESETTING TO FACTORY DEFAULT As 1080p 3D Stereo is the default factory setting for the matrix to reset EDID of all ports simply set the DIP switch to the above position when the matrix is powered OFF On powering ON all ports will revert to 1080p 3D Stereo and DIP switches can be adjusted as necessary www vanco 11 com 1080p Stereo using embedded A series EDID The matrix will use embedded 1080p video and stereo audio in this DIP setting After setting the DIP switch reconnect and turn on for EDID settings to take effect 1080 Stereo using embedded L series EDID In instances where a connected display is unable to achieve 1080p resolution such as using older or cheaper models this DIP setting will instruct the matrix to use embedded 1080i video and stereo audio to output a signal After setting the DIP switch reconnect and turn on for EDID settings to take effect 1080p 5 1ch Audio using embedded D series EDID When set to this DIP position the matrix will use embedded 1080p video with 5 1ch Audio After setting the DIP switch reconnect and turn on for EDID settings to take effect 1080p 7 1ch Aud
3. Distribution of HD signals through the matrix requires mutual communication or handshake between source and display If there is any disparity between the two successful transmission becomes problematic This matrix comes equipped with an EDID DIP switch on the rear panel for manual adjustment of matrix Settings to encourage communication between INPUT and OUTPUT devices If installation compatibility issues arise check the settings on your connected devices and adjust the DIP settings as required ATTENTION Changes to the DIP switch settings should be made with the matrix OFF ideally with all power cables and HDMI leads and UTP cables removed to guard against electrostatic build up that may damage your system DO NOT HOTSWAP your cables when changing DIP SETTINGS ALL changes to the DIP settings become effective upon powering ON the matrix EDID Copy from Output display to Input port Force Signal Output mode To copy the EDID from an OUTPUT display to a specific INPUT port first set the DIP switch to this position Then select the INPUT by pressing and holding the chosen OUTPUT SELECT button for 3 seconds for the EDID to be copied from the DISPLAY to the INPUT port OUTPUT2 CEAD Select the INPUT you wish EDID to be copied onto PRESS and HOLD the OUTPUT SELECT button for 3 seconds for the OUTPUT EDID to be copied to the selected INPUT SELECT 1080p 3D Video Stereo Audio using embedded M series EDID FACTORY DEFAULT
4. FRONT REAR D Mounting brackets 06 RS232 Port 1 Input select button click to scroll numerically LAN port for control via the internet 03 Input selection per output lit to show input currently TJ EDID DIP Switch selected for output DT 19V DC power input 04 saten 10 IR RX extension port a PONOT SNAR ETI Output ports RJ45 Cat5e 6 7 EPI Input ports HDMI EE IR TX Emitter port corresponds to inputs DISPLAY RECEIVER PANEL D Power status LED Lit when unit is powered 05 5v DC power input can also be powered by 1 Signal status LED Lit when transmission is received USB to 5V power adapter USBDODIX USBDCOZX 03 Cat5e 6 7 connector 04 IR RX receiver port placed on or near display TV in clear line of sight to remote handset used to control 06 HDMI out port for display projector EQ adjustment fine tuning signal to optimise strength distance FRONT DC 5V www vanco 11 com BASIC OPERATION Front Panel Control y 4 outPUTI outrur2 ns mean ourruts n Basic switching of various source inputs to output displays can be achieved via the front panel control of the VPW 280755 Outputs are numbered 1 4 with an input select button to the left Repeated pressing of the select button of a specific output scrolls through the HDMI input devices connected to the matrix with the corresponding LEDs illustrating when a device has been selected for that particular output The chose
5. panel IR sensor be an issue for example if the sensor is obstructed or the unit is installed in a closed area out of infrared line of sight the IR RX Receiver included with VPW 280755 can be inserted into the IR EXT port at the rear to extend the IR sensor range and enable local control of the matrix ADVANCED OPERATION Typically unless alternative methods of controlling the matrix are chosen or problems with device communication through the matrix encountered basic operation is all that is required to operate your VPW 280755 However the following information on advanced operation will detail how the matrix system can be configured for advanced control and settings altered or data manually input should such problems arise as well as configuring the system for third party control IR Call Back and Third Party Control systems Toggle numerically forwards backwards through connected source devices Select specific source numbered ATTENTION Due to the differing method of control based on location if you are using a third party control system learning the control from the IR is NOT recommended as control will be limited to scrolling up down between inputs For discrete source selection you will need to import discrete hex codes for control systems These can be obtained through the Wyrestorm website by contacting our Output port number Output source select key code 0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87 Output2 source
6. policy to modify and or improve its products where necessary or desirable This statement does not affect the legal rights of the user in any way LIMITED WARRANTY With the exceptions noted in the next paragraph Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of one year from the date of purchase Should this product in Vanco s opinion prove defective within this warranty period Vanco at its option will repair or replace this product without charge Any defective parts replaced become the property of Vanco This warranty does not apply to those products which have been damaged due to accident unauthorized alterations improper repair modifications inadequate maintenance and care or use in any manner for which the product was not originally intended Items integrated into Vanco products that are made by other manufacturers notably computer hard drives and liquid crystal display panels are limited to the term of the warranty offered by the respective manufacturers Such specific warranties are available upon request to Vanco A surge protector power conditioner unit or a uninterruptible power supply must be installed in the electrical circuit to protect against power surges If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt or other acceptable proof of purchase to the seller of
7. select key code 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 Output3 source select key code Oxa0 Oxa1 Oxa2 Oxa3 Oxa4 Oxa5 Oxa6 Oxa7 Output4 source select key code OxbO Oxb1 Oxb2 Oxb3 Oxb4 Oxb5 Oxb6 Oxb7 technical support or you can input them manually REFERENCE The IR is NEC and possesses a carrier wave of 38KHz with a system code of 0x00 RS282 Control Control of the matrix is possible through R5232 using third party control systems or the dedicated COM CTL software included with your purchase also downloadable from http www vanco1 com Should third party control be required please see below for control system configuration and hex code input The RS232 connection on the matrix is female QBY Users can use a USB to RS232 cable or a direct male to female serial cable RXD Receive serial data from PC TXD Transmit serial data to PC Com Port Setting y600bps Male connector 9 holes Sss 769 4156 E VANGO yu 1 CONNECTIVITY COM CTL Control of matrix switching and system settings is possible using the COM CTL software included with SLO your purchase After fully connecting all inputs and ETT seco LI Co outputs to the matrix and installing the software on Message m KE FE opening the program the control window will display ERE a r information from the matrix such as messages received from the switch such as input output details firmware version and control commands HEX codes HA EXE
8. the name of your matrix from the factory default 0000000000 just right click on the serial number and select rename from the dropdown LLoginJ menu Input the new name and press OK Double click on the device name default factory serial number or right click and OPEN and you will be directed to a web login page in your internet browser MATRIX 4 4 WEB CONTROL wi Enter the default password of ten zeros 0000000000 and click LOGIN to take you to the NET CTL matrix controller LA mm mm mm um screen TT op 2 MEN mal A The layout of the NET CTL controller screen includes an upper section to allocate input sources to output with the selection displayed on the left hand side Operation is the same as COM CTL Inputs buttons 1 4 can be clicked to be selected per Output port IROUT4 m mm m _ www vanco 11 com Press the REFRESH button to update your chosen matrix settings into the left hand display and your selection to take effect B The lower section of the NETCTL controller screen is dedicated to IR Matrix settings As with the IR Matrix screen in COMCTL the NTCTL IR Matrix allows specific SOURCE IR ports to be manually set to individual DISPLAY ports to configure specific IR configurations through the matrix Press the REFRESH for IR Matrix changes to be set This function is available only when the matrix is connected to receivers via UTP and all units fully powered C
9. 0 3lbs Operating Temperature Range ssssssess 5 to 35 C 23 to 95 F Operating Humidity Range ll llllveeeeerteeereereeeereooeeooe 5 to 90 Yo RH no condensation Video Amplifier Bandwidth s e 6 75Gbps input Video Signal raze adr s mat ik ee di ai ad kaa ctn tu 0 5 1 0 volts p p Input DDG Signali ivissasonaaikwitiwasyot oka miray verna abus MATRIX 12 volts p p TTL RECEIVERS 5 volts p p TTL Maximum Single Link Range 1080p 24bit color depth Transmission distance 20 0 eee cece ecceececeeaueeeeueeeeaueses 1080p signal up to 40m 131 ftft Under perfect transmission conditions including straight cable runs with no electrical interference bends kinks patch panels or wall outlets Video Format Supported cccccccseceeseeseeueeeeeueees VESA 640x480 800x600 1024x768 1280x1024 1600x1200 1920x1200 DTV HDTV 480i 576 480p 576p 720p 1 080 1 080p utnul VIE Wes acre critt nt S kb DARE BE HDMI v1 2 HDMI v1 3 HDCP Output display mirrors the Input source Audio Format Supported cccccccseeceseseeueeseeueees Fully supports Dolby True HD and DTS HD mirrors input audio source to the output display mul d MATRIX 100 240V AC RECEIVERS SVDC mains or USB 5V power adapter Power Consumption ssss e MATRIX 22 Watts max RECEIVERS 1 5 Watts max Hack Space Required sssssm MATRIX 1U PACKAGE C
10. ONTENTS Before attempting to use this unit please check the packaging and make sure the following items are contained in the shipping carton 1 Vanco Powered by Wyrestorm VPW 280755 Matrix Unit 4 e e 4 Display receivers e 1 12VDC Power Supply for Matrix Unit 4 SVDC Power Supplies for display receivers e Product Manual e Mounting brackets with screws for both Matrix Unit and display receivers e 1 IR Remote 1 IR RX Extension Cable e 4 IR TX emitters small for input source 4 IR RX receivers larger for displays VVAV AV AAYA JaleloM B elo na 7 CONNECT AND OPERATE Apple TV BluRay Player Console HDTV HDTV HDTV HDTV Connect up to 4 sources such as a Blu Ray Player game console A V Receiver Cable or Satellite Receiver etc to the HDMI inputs on the unit Do not hotplug Insert and extract cables carefully with the power SWITCHED OFF Connecting and disconnecting while the unit is powered can result in damage to circuitry Connect the output UTP output ports starting with output 1 to the included display receivers using well terminated or pre terminated Cat5e 6 cables no longer than 131 ft Connect the output HDMI ports of the display receivers to high definition displays such as an HDTV or HD projector that use HDMI inputs Note that high speed HDMI cables are recommended for the distances that are required for each connection Plug in IR transmitters to the bac
11. S that allow the system to be controlled remotely as n well as buttons used to navigate the screen meee 1 Receive Message Window displays messages ELA NS EX EZ received from the matrix such as input output settings and command selections You can view EIA alas EIEN the current condition of all input output ports by Connect State Com Select 4 i DE Connected comi I pressing the STATUS button Pressing CLEAR Q Disconnect will delete the previous message received in the ca window 2 Send Message Window Input your serial commands for the matrix in the Send Message Window such as instructions for outputs or to enter update mode and click the Send button to deliver the message to the Matrix The control command uses ASCII RS282 Control To update the system firmware enter the following code into the Send Message Window 02 ensuring to include one space between each section of the code Code ICP BE 7C 5F Press Enter then Send Message SEND to put the matrix into firmware update mode Press the Disconnect 05 button and run the firmware When the firmware has finished updating press the same button again to Connect and power cycle the matrix turn off and on Updates are now active and the firmware is now updated ATTENTION To see the firmware version currently used in the system power off and repower while the matrix IS connected to COM CTL The firmware version and creation date will be displaye
12. STALL BASIC GLE UTP HDMIP Mick INSTAL OVER UTP IN K RS AX4 Quic DC 5V HDMI DISTANCE PRODUCT MANUAL Vanco Part Number VPW 2830 755 STANGO power WuyreStyrm www vanco M colo asm mt 888 769 4156 DEAR CUSTOMER Thank you for purchasing this product For optimum performance and safety please ve P read these instructions carefu ly DETONI connecting operating or adjusting this product Please keep this manual for future reference This product is 100 inspected and tested in the United States to verify HDMI performance parameters WARNING 1 Do not expose this unit to water moisture 6 Only clean unit with a dry cloth or excessive humidity 7 Unplug unit during lightening storms or 2 Do not install or place this unit in a built in when not used for an extended period cabinet or other confined space without of time A surge protector is strongly adequate ventilation recommended 3 To prevent risk of electrical shock or fire 8 Protect the power cord from being walked hazard due to overheating do not obstruct on or pinched particularly at the plugs unit s ventilation openings 9 Use unit only with accessories specified by 4 Do not install near any source of heat the manufacturer including other units that may produce heat 10 Refer all servicing to qualified personnel 9 Do not place unit near flames CAUTION HDMI is a very complex te
13. W 280755 is a solid choice for any application Vanco Powered by WyreStorm Quick Install Basic HDMI 4x4 Matrix over UTP Part VPW 280755 Enables up to 4 HDMI video audio devices to be independently switched to 4 HDMI displays or projectors for uncompressed digital distribution up to 40m 130ft over a single Cat5e Cat6 cable Each output is able to show any connected source simultaneously regardless of whether the input carries HDCP encryption Designed work seamlessly together for complete compatibility and full management of handshakes screen resolutions and HD signal distribution to each display point whether in a residential or commercial environment Fully cascadable so multiple units may be combined to create a larger HD distribution Reads and copies EDID from connected devices with additional EDID configuration through customizable DIP switch settings Simplified ports Input HDMI Output integrated RJ45 connectors for a single Cat5ei 6 7 UTP cable to each display point for ease of installation Conforms to IEEE 568B standards Each HDMI port also supports DVI signals Fully 3D compatible Frame sequential 3D Blu ray and interlaced stereoscopic 3D satellite broadcasts etc Supports all high definition resolutions up to 1080p 2k resolution supported For even greater control and fine tuning each receiver features a fully adjustable EQ distance range for optimizing the transmission signal Protection ag
14. WINDOWS system32 cmd exe osoft Windows KP CARA 5 1 2600 KI 3 1985 2081 Microsoft Corp TELNET Control Control of matrix switching and system settings are also possible using Telnet control protocols Follow system commands below ocuments and Settings user gt telnet 192 168 08 3 ATTENTION This Assign IP process differs from the COM CTL IP Set function Set IP in COMCTL saves reads the IP address in flash and sets it as static IP Assign IP is only used when the system fails to obtain an IP address automatically and is NOT saved in flash Assign IP Read Device S If Assign IP is displayed in the dialog box the matrix has encountered a problem detecting an IP address and manual input Click of information is required NewlP 192 168 0 100 i 255 255 255 0 In such instances Subnet double click Assign Gateway 255 255 255 255 IP or right click and choose Assign IP from the dropdown Cancel menu to add details as required to assign the new IP address to the system and you will return to the previous screen or MAC 00 0B 3C 03 79 0F Cancel to return without changes taking effect Now click for the Matrix to detect the new IP address which will appear in the dialog box Finally click Read Device to confirm IP settings Sss 769 4156 L ABBWANCING CONNECTIVITY VPW 280755 EDID DIP SWITCH SETTINGS
15. ainst ESD electrostatic discharge included within the receiver units to further stabilize transmission Receivers feature LED indicators for clear power and video signal selection RS232 port Choose from 6 switching modes infrared remote control front panel buttons local IR IR call back LAN and RS232 Simple switching remote control included which can also be learned into a universal remote handset to allow the control of multiple devices from one handset Fully compatible for integration with market leading control systems 4 x IR 3 5mm mini jack ports for each output to link IR from control system to control display Receivers includes additional infrared extension port for longer IR connections HDMI v 1 3 Supports 24Bit Color depth Signaling rate of 6 75 Gbps Pack comes complete with 1 x 4x4 Matrix with 19 brackets 4 x 40m IR receivers with mounting brackets IR receivers emitters and a Matrix remote control 12V DC UL Listed Power supply for 4x4 matrix 5V DC UL Listed Power Supplies for Receivers 4 total 4x4 Matrix Dimensions 17 25 W x 2 05 H x 9 25 D Receivers Dimensions 2 4 W x 09 H x 4 5 D Sss 769 4156 ADVANCING CONNECTIVITY SPECIFICATIONS Dimensions WXHXD llllelllileeeorerreeerteteerreoteeeosoonnes MATRIX 440mm 17 3 x 5amm 2 05 x 230mm 9 25 RECEIVERS 60mm 2 4 x 115mm 4 5 x 23mm 0 9 Weight IKO MATRIX 2 Kg 4 4lbs RECEIVERS 0 15 Kg
16. al to desired distance setting Changes become effective when turned back ON www vanco 11 com EQ MIN MIN 4 DISTANCE DC 5V HDMI OUT DISTANCE 0 16ft Transmission Distance 16 33ft Transmission Distance 33 49ft Transmission Distance 49 65ft Transmission Distance 65 82ft Transmission Distance 82 98ft Transmission Distance 98 115ft Transmission Distance 115 131ft Transmission Distance Default position 7 recommended for initial connection and operation If signal requires fine tuning move through the following settings until desired image quality is achieved No function settings reserved for future updates Sss 769 4156 VANCO ABBWANCING CONNECTIVITY LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly All rights are reserved No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical including photocopying recording or by any information storage or retrieval system without the written consent of the publisher Manufacturer reserves the right to revise any of its hardware and software following its
17. ce that is on and will try to connect to the signal 5 Most of the major player and display manufacturers employ a proprietary control channel to communicate between devices from the same manufacturer Sometimes this can interfere with the HDMI control circuit or the authentication of the signal Call the manufacturer if you experience this problem Sometimes a player an audio video receiver or a cable satellite box may not have the latest software update and needs to have this downloaded from the manufacturer s web site TECHNICAL SUPPORT In case of problems please contact Vanco Technical Support by dialing 1 800 626 6445 or 1 888 769 4156 You can also email technical support issues to info vanco com When calling please have the Model Number Serial Number affixed to the bottom of the unit and Invoice available for reference during the call Please read this Instruction Manual prior to calling or installing this unit since it will familiarize you with the capabilities of this product and its proper installation All active electronic products are 100 inspected and tested to insure highest product quality and trouble free installation and operation The testing process utilizes the types of high definition sources and displays typically installed for entertainment and home theater applications For additional information such as helpful installation videos glossary of terms etc please visit www vanco 1 com Sss 769 4156
18. chnology requiring continuous authentication of the signal and the same video resolution and audio settings on all electronic equipment in the system When there are multiple sources and displays the video resolution and audio setting on all connected units must be adjusted to correspond with that of the display having the lowest video and audio capability www vanco 11 com Vanco Powered by Wyrestorm Quick Install 4x4 Matrix over UTP with R5 232 is an HD switching and extension system that comprises of a 4 input 4 output HD Matrix together with included 4 display receivers Have 4 sources displayed simultaneously on any display or have a single source duplicated on multiple displays flexibility for the perfect solution Simple plug and play solution that allows each output with the ability to extend HDMI signal up to 131 feet over a single category 5e or 6 cable With an output bandwidth of 6 75 Gbps the VPW 280755 is capable of full 1080p HD video and HD multi channel audio distribution with simple control using the front panel or remotely via IR Receivers at display locations Also features EDID management system which allows and encourages device communication compatibility for seamless integration Includes RS232 connectivity for firmware updates or third party integration for control and switching For the quickest most convenient and cost effective means of transmitting and controlling full uncompressed 1080p HD video and HD audio the VP
19. co1 com and run the program by double clicking NETCTL exe 5 ATTENTION Use a straight through ethernet cable for switch router connection and a cross over cable for connection to a PC Using the incorrect cable will Search Read Device not damage your equipment but it may result in poor no connection Make sure mon that your LAN cable is correctly terminated and firmly connected to ports before running the software On initial opening the program will first create a NETCTL TXT file that will serve as a device backup for future use including connection Device Name settings such as IP address and MAC Search Read Device address of the VPW 280755 as well as its name if you decide to TEE change the name of your matrix see Device Name section below Open On subsequent openings NETCTL will then search the Matrix for the Wore Info saved data required for connection If using for the first time the program will automatically detect the IP i address being used with the result displayed in the white area beneath Should no result appear or if the system is unable to detect an IP address Met mene ee automatically press the SEARCH button to locate When the IP address appears click READ DEVICE to attach the IP address to the system and the IP address will change to a default factory serial number MX0404 QI or MATRIX 4 4 WEB LOGIN Password MX0404 HDC Password Should you wish to change
20. d together with the normal output state of the matrix 3 Com Connect State Shows if the matrix is connected or disconnected to the Com Port and communication is enabled Selection between ports is available by pressing the Com Port Select button When connected the only option will be to Disconnect and vice versa Press to connect disconnect the matrix from the software control Connect State Com Select eConnected to ENABLE matrix communication Bn e M v sconnec a Di t eDisconnected to DISABLE matrix communication S ones 4 Com Select NOTE The Com Select drop box offers options of Com 5 Connect Disconnect Ports to connect to COM 1 10 Click the Com Select dropdown to see all Com ports available Select your chosen Com port number and press the CONNECT button You will notice the button change to show disconnect and CONNECT STATE change to green for connected Pressing the button again will disconnect the Com port and the CONNECT state will show red www vanco 11 com 6 Set IP Button allows you to set the IP address to be used by the system The matrix can also be controlled over LAN Selecting the Set IP button 06 in the main COMCTL screen allows access to IP functions that obtains and stores IP address information necessary for LAN control Clicking opens a pop up window in which you can choose to let the system automatically detect your IP address with the result displayed in the box bel
21. ed receiving areas of devices can be located by shining a flashlight onto the front of the device the sensor should be able to be seen through the plastic as a Small round object inside 2 At display end Insert the IR RX Receiver jack into the IR RX port of the display receiver baluns with the IR receivers themselves placed in clear view on or near the displays to receive an infrared signal from the remote handset used to control inputs Fasten firmly to the surface to avoid displacement ATTENTION Misplaced or poorly secured IR Emitters and Receivers may result in intermittent IR control signals passed to and from the matrix Check your placement and adjust if necessary HINT If problems are encountered controlling devices remotely check IR TX Emitters and IR RX Receivers are correctly positioned and connected to sources displays and display receivers with all devices fully powered and the matrix set to IR call back enabled and IR TX Switch mode activated See COM CTL section for Call back enablin HDMI Source HDMI Input 1 IR TX 1 HDMI Input 2 IR TX 2 HDMI Input 3 HDMI Input 4 IR TX 4 HDMI Cable UTP Out 2 UTP Out 3 UTP Out 4 Cat5e 6 7 up to 40m 131ft IR Receiver DA IR TX IR emitter r Negivate Positive STATUS IR Extender Control Front Panel AY VAY VAY YAYA JaleloM B elo na Should local control of the Matrix via the front
22. er To change handset battery E Jele Install battery side up and only use CR 2025 3V batteries Slide compartment back into the handset VANGO ABBWANCING CONNECTIVITY This is accomplished by placing a series of IR Emitters on source devices you wish to control and IR Receivers at all output locations you wish to control from to enable the IR control signal to be delivered via single Cat5e 6 7 cable connecting the two 1 At Matrix end Insert the 3 5mm jacks of the IR TX Emitters included with the unit into the IR TX Emitter ports at the rear of the matrix according to input The IR signal is added to the HDMI of the input device so for example if the user is watching Blu ray on input 3 the IR signal will be directed through the IR TX3 socket to control the device As each IR TX port is allocated to an individual HDMI input port if the user is unable to establish IR control of the device care should be taken to check that firstly the IR emitter and HDMI input ports match Input 1 TX1 Input2 TX2 etc with plugs secured in correct ports and secondly that the IR TX emitter sensors are firmly attached directly to the front of inputs and covering infrared sensor windows of the source devices Some later adjustment may be needed to the location of the sensor to achieve the best performance results sometimes moving the sensor to different areas on the source can improve IR performance HINT infrar
23. io using embedded G series EDID When set to this DIP position the matrix will use embedded 1080p video with 7 1ch Audio After setting the DIP switch reconnect and turn on for EDID settings to take effect Sss 769 4156 ABBWANCING CONNECTIVITY AVR 7 1 Audio EDID COPY to Blu ray source AV Receiver copy For users who wish to copy EDID from an AV Receiver with 7 1 channel audio to a specific input port containing a Blu ray player follow a variation on the instructions above 1 Set the DIP switch to the above position with the matrix in the OFF position Connect the AVR to your desired OUTPUT port on the matrix for example OUTPUT 2 Power ON the matrix and select your INPUT on the AVR making sure your chosen SOURCE is connected to for example INPUT 3 Blu ray 4 Press and hold the OUTPUT SELECT button for 3 seconds for the EDID data to be copied from OUTPUT 2 AVR to INPUT 3 Blu ray Remaining settings no function reserved for future updates EQ Distance Adjustment Settings Occasionally the installation environment such as the distance between source and display may be a factor in the perfect transmission and reception of a signal In addition to the VPW 280755 LONG CABLE settings on the Matrix DIP switch the RECEIVER balun can be further fine tuned depending on the length of Catde 6 7 cable used for optimum performance ATTENTION Please ensure the balun is switched OFF when changing the di
24. k of the Matrix Selector Switcher unit IR TX the transmitters are labeled IR TX place in front of the IR receiver of the source ensure that each emitter is placed in front of the IR receiver eye Double sided adhesive tape provided Plug in IR receivers to the port of the display receiver baluns IR RX the receivers are labeled IR RX use provided double sided adhesive tape to stick emitters at each display at a desired place that will receive a remote signal For power plug in the source first followed by the Vanco Powered by Wyrestorm Matrix Selector Switcher power supply included followed by each output connected Power on each device in the same sequence At this point each display connected should display the assigned source input 1 at default when powered on initially scroll through each of the sources on each display to ensure everything is in working order Use included IR remote at each display receiver to test switching function between sources and IR function itself If a display is having difficulty receiving a signal access the displays menu and adjust the resolution lowest to highest until signal is displayed A 24 Hz vertical refresh rate may work better than 60 Hz or higher If the IR remote function is not responding check the emitters to ensure they are placed correctly and are plugged into the correct IR jacks on the Matrix Selector Switcher unit Sss 769 4156 powered by FRONT AND REAR PANEL
25. lable only when the matrix is connected to receivers via UTP and all units fully powered IR Matrix allows manual selection of source device ports 01 by Display Receiver ports 02 The dropdown menu 03 allows ALL IR TX ports to be set to ONE specific INPUT device IR RX port with the current settings of the IR Matrix viewable by pressing the STATUS button 04 9 Input Output Switch Switches connected inputs per output Operation as with remote control handset select the chosen input to be displayed on each output by either clicking the left right arrow buttons to scroll through inputs numerically or pressing the input number 1 4 A large yellow number denotes each OUTPUT section with INPUTS chosen by either clicking the left right arrow buttons to scroll through inputs numerically or by pressing the input numbers below The INPUT OUTPUT switch allows output port selection display and Input port select source buttons for specific combinations of displays and sources within the matrix DP Lifi DE r1 ALL IR PORTI Status Sss 769 4156 NETCTL LAN Control a The matrix can also be controlled via LAN over a network web browser using the supplied NET CTL software or LAN protocols from third party companies such as Search Read Device Control 4 and TELNET Control for all control systems As with COM CTL install the NET CTL software included with the matrix also downloadable from www van
26. n input will automatically store for the output so even when the matrix is powered off and on on resumption the last selected input output combination will remain ATTENTION Users will notice a brief flicker on screen when switching between inputs outputs this is normal for this model and represents the matrix resetting device HDCP settings to allow communication from a different device For constant HDCP when switching with no noticeable screen resets see Wyrestorm PRO Pro Plus and HDBaseT matrix ranges See wyrestorm com for more information The same basic functions can also be accessed via the remote control Operation of the handset is the same regardless of location locally source IR emitter or remotely display IR receiver Simply toggle through the input sources connected to the matrix by either pressing the left right arrow buttons or buttons numbered 1 4 for each output IR Gall back of Matrix and Source Devices The VPW 280755 is not only a switcher and extender of multiple HDMI signals to multiple HDMI receivers located remotely it also passes IR control signals through the IR call back system to the matrix and HDMI sources for full independent control of all connected inputs from output locations using your remote handset Remote Control Local IR Select specific source numbered 1 4 Sss 769 4156 Toggle numerically forwards backwards through connected source devices Output port numb
27. ow Alternatively if the system Automatically obtain ip address cannot detect an IP address select Use the following IP Address and you can add manually 01 Selection enables the IP address to be obtained IP address automatically with the result appearing in the white box below 3 m Set IP Use the following ip address 02 Should no address appear or if the system is unable to detect an IP address select option 03 to manually input the IP address 04 Click DK to complete the process or CANCEL to exit and return to the main screen NOTE To access matrix control over LAN enter the IP address of the matrix into your internet browser and you will be directed to the web control screen For full information on LAN control see NETCTL section of this manual 7 UTP Set Default setting is OFF for normal Matrix operation to obey device EDID HDCP commands and high hotplug settings when outputting a signal Switching output settings to ON instructs the matrix to output a signal regardless of device EDID HDCP or hotplug data such information is circumvented to encourage communication in the event of problems between sync devices We recommend this setting for system debugging by the installer and not for operation by the end user 8 IH Matrix IR Matrix allows specific SOURCE IR ports to be manually set to individual DISPLAY ports to configure specific IR configurations through the matrix This function is avai
28. this equipment The seller will then contact Vanco regarding warranty repair or replacement www vanco 11 com TROUBLE SHOOTING 1 Best results are usually achieved when the source and display resolutions are the same If resolutions differ the extenders will try to adjust the signal to match the resolution of the HD TV with the lowest resolution This will result in a picture with a lower resolution on the other HD TV sets 2 If you do not get audio and video see if you can use the set up menu on the TV to adjust the audio settings and the video settings If the HDMI control circuit cant establish a hand shake then there usually will be no audio or video and a blue or black screen with a statement like this protocol not supported or weak signal 3 If you get the above messages re set the Receiver by disconnecting the power supply Alternately you can disconnect all of the HDMI and power cables wait 10 or 15 minutes for any voltages to decay and then connect all of the cables from the source to the Receiver and to the display 4 f you still have trouble then try the hot plug concept Turn on the source and plug the HDMI cable to it and then power up the Transmitter and plug the cable into it then plug the output cable into the Receiver and finally turn on the display and plug the HDMII cable from the Receiver into it This activates all of the devices in order and results into a signal being plugged in to a devi
Download Pdf Manuals
Related Search