User-Manual - Newegg.com
Contents
1. Click Finish Click Yes to complete the installation Server 2003 32 bit For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below ile 2 Install the board and follow Microsoft procedures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 32bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D XP_Vista setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish then click Yes to complete the installation Windows XP 64 bit For New Installation A new installation requires a floppy disk for the driver installation To m2. where you purchased from B If your purchase has passed the store s return policy period please follow the steps below to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then REQUEST A PRODUCT REPLACEMENT to submit a request to SUG RMA or fax a request to 510 657 5962 Your RMA request will be processed if the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are responsible for the cost of shipping to SIIG Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 19 About SIIG Inc Founded in 1985 SIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG c
3. AA DP SATA 6Gb s 2 Port PCle w Installation Guide Introduction The DP SATA 6Gb s 2 Port PCIe adds 2 SATA 6Gb s channels to PCle equipped computers Features and Benefits Adds 2 internal SATA 6Gb s channels to your PCle system Compliant with Serial ATA specification Revision 3 0 Supports ATA ATAPI 7 specification Installs in standard height or low profile chassis with included brackets System Requirements 04 0743C Desktop PC with an available PCle slot Windows 8 32 64 bit 7 32 64 bit Vista 32 64 bit XP 32 64 bit Windows Server 2003 amp 2008 32 64 bit Server 2008 R2 Server 2012 Server 2012 R2 1 Package Contents e DP SATA 6Gb s 2 Port PCIe adapter e Spare low profile bracket e SATA data cable e Driver CD amp Installation guide Layout k Hard Disk LED Pins connect horizontally Serial ATA Connector Figure 1 DP SATA 6Gb s 2 Port PCIe Hardware Installation For low profile systems install the spare low profile bracket now General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by the
4. ake this floppy disk copy the contents of the 64bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 2 Install the board and follow Microsoft procedures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 64bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again then follow the on screen instructions to complete the installation For Existing Installation 1 2 6 7 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D XP_Vista setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Windows XP 32 bit For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows acc
5. ess Enter Change D to match your CD ROM drive letter At the User Account Control window click Allow Skip this step if not prompted Click Next Select I accept the terms of the license agreement then click Next Click Finish then click Yes to complete the installation For Existing Installation 1 2 3 Install the board and boot up Windows At the Found New Hardware click Cancel Insert driver CD click Start menu in the Start Search box type D XP_Vista setup exe press Enter Change D to match your CD ROM drive letter 7 8 At the User Account Control window click Allow Skip this step if not prompted Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Windows Server 2008 32 64 bit For New Installation 1 2 Install the board and follow Microsoft procedures to install Windows accordingly After the installation insert driver CD click Start menu in the Start Search box type D XP_Vista setup exe press Enter Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish then click Yes to complete the installation For Existing Installation 1 2 6 7s Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu in the Start Search bo
6. f their respective owners February 2015 Copyright 2015 by SIIG Inc All rights reserved
7. indows 8 7 Vista Server 2008 Server 2008 R2 Server 2012 Server 2012 R2 Double click Storage controllers Asmedia 106x SATA Controller should be displayed For Windows XP Server 2003 Double click SCSI and RAID controllers Asmedia 106x SATA Controller should be displayed 17 Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analyst will promptly respond SIG offers a 5 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for five 5 years from the date of purchase of the product SIG will at our discretion repair or replace with an identical product or product having similar features and functionality the product if defective in materials or workmanship This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store
8. ir external edges 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer ad Remove your computer cover 4 Remove the slot bracket cover from an available PCI Express slot To install the card carefully align the card s bus connector with the selected PCI Express slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card Device Connection The DP SATA 6Gb s 2 Port PCIe is a dual channel Serial ATA III controller that supports up to two Serial ATA hard disk drives If you plan to use the second channel you will need to purchase another SATA data cable 1 2 Install your hard disk drive s in the chassis Connect the hard disk drive s power connector to the system power supply Note For hard drives with both SATA power connector and legacy 5 pin connector use either the SATA power connector or the legacy 5 pin power connector Using both power connectors may damage the hard drive 3 Connect one end of the Serial ATA data cable to the hard disk drive Serial ATA data cable Power cable Figure 2 SATA hard disk drive connections Attach the other end of the Serial ATA data cable to the Serial ATA connector on the DP SATA 6Gb s 2 Port PCIe Follow the same instructions to connect the second hard drive if needed De
9. ontinues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as wellas one of the lowest defective return rates in the industry SIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME DP SATA 6Gb s 2 Port PCIe FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 DPSATA 6Gb s 2 Port PCIe is a trademark of SHG Inc SIIG and the SHG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation All other names used in this publication are for identification only and may be trademarks o
10. ordingly 15 At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 32bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D XP_Vista setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish then click Yes to complete the installation To Verify Windows Installation 1 Use Device Manager to verify installation For Windows 8 7 XP Server 2003 amp 2008 R2 Right click Computer or My Computer click Manage click Device Manager For Windows Vista Right click Computer click Manage click Continue Click Device Manager For Windows Server 2008 Right click Computer click Manage Double click Diagnostics click Device Manager For Windows Server 2012 2012 R2 Right click Computer or This PC click Properties then click Device Manager For W
11. vice connection is now complete Software Installation This section provides information on how to install the DP SATA 6Gb s 2 Port PCIe adapter drivers Windows 8 32 64 bit Windows 7 32 64 bit Server 2012 Server 2012 R2 Server 2008 R2 For New Installation I 2 Install the board and follow Microsoft procedures to install Windows accordingly After the installation insert driver CD Double click Computer or This PC on the desktop then the CD ROM drive Select Win 7_8 folder and run setup exe At the User Account Control window click Yes Skip this step if not prompted Click Next Select I accept the terms in the license agreement and click Next Click Finish then click Yes to complete the installation For Existing Installation 1 2 Install the board and boot up Windows Insert driver CD Double click Computer or This PC on the desktop then the CD ROM drive Select Win 7_8 folder and run setup exe At the User Account Control window click Yes Skip this step if not prompted Click Next Select I accept the terms in the license agreement and click Next Click Finish then click Yes to complete the installation Windows Vista 32 64 bit For New Installation 1i Zs Install the board and follow Microsoft procedures to install Windows accordingly After the installation insert driver CD click Start menu in the Start Search box type D XP_Vista setup exe pr
12. x type D XP_Vista setup exe press Enter Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Server 2003 64 bit For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 64bit folder found on the driver CD onto a blank floppy disk then follow the directions below Is Install the board and follow Microsoft procedures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 64bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D XP_Vista setup exe click OK Change D to match your CD ROM drive letter 11 6 7 Click Next Select I accept the terms of the license agreement then click Next
Download Pdf Manuals
Related Search