DEA-8205 User Manual iss06 - AV-iQ
Contents
1. General Business Office and Technical Support eG ne mene PHONE After Hours Emergency 613 349 0006 Fax 613 652 4425 General Information solutions rossvideo com E MAIL Technical Support techsupport rossvideo com 8 John Street Ross Video Limited Iroquois Ontario Canada KOE IK POSTAL i SERVICE P O Box 880 Ross Video Incorporated Ogdensburg New York USA 13669 0880 Visit Us Please visit us at our website for Company information Related products and full product lines On line catalog News Testimonials TW AsEEjvideo com Ross Video Part Number 8205DR 004 062. MIB Management Information Base file for a breakdown of SNMP controls on this card Refer to your MF C 8300 Series User Manual for additional information on SNMP Monitoring and Control 4 2 Menus DEA 8205 User Manual Iss 06 DashBoard Control System Software This section briefly summarizes the menus items and parameters available from the DashBoard Control System for the DEA 8205 Parameters marked with an asterisk are the factory default values The DashBoard Control System enables you to monitor and control openGear frames and cards from a computer DashBoard communicates with other cards in the DFR 8300 series frame through the Network Controller Card Status Menus Table 4 1 summarizes the Status tab parameters available in DashBoard for the DEA 8205 The Status tabs provide read only information such as software revision issue and power consumption Note The Channel A Rate or Chanel B Rate in the Setup menu affect the Slew Rate of the output driver Ensure that the correct standard for your input is selected Table 4 1 Status Tab Items Tab Title Product Read only Hardware Read only Signal Read only Product Parameters DEA 8205 Description Product Supplier Ross Video Ltd Supplier Board Rev Hit Board Rev Serial Number THEHHHUIHHI Serial Number Software Rev Voltage mV Software Rev Supply Voltage Current mA Current consump
3. input signal is present a valid reference signal is present when a reference is required and that the reference standard matches the input standard Flashing Green When flashing green this LED indicates that the Bootload button was pressed and the card is receiving a new software load from the frame Flashing Green and Orange When lit green with flashing orange this LED indicates a signal or configuration problem Verify the signal status and settings Amber When lit amber this LED indicates the card is running internal diagnostics while powering up Red When lit red or flashing red this LED indicates the card is not operational Re seat card in frame check the rear module type and connections or call Ross Video Technical Support DEA 8205 User Manual Iss 06 When off this LED indicates there is no power to the card User Controls 3 3 Table 3 1 LEDs on the DEA 8205 Display and Description When lit this LED indicates that the signal is passing through CHA Channel A without errors OK ERROR When red this LED indicates the absence of an input signal on Channel A When lit this LED indicates the channel is processing an HD input signal rate 1 485Gbps When lit this LED indicates the channel is processing an SD input signal rate 143Mbps 177Mbps 270Mbps 360Mbps or 540Mbps When lit this LED indicates that the signal is passing through CHB Channel A without
4. set the input signal rate type that Channel B will process Pressing the button cycles between the HD and SD options You can choose between the following signal rate types HD 1 485Gbps e SD 143 177 270 360 and 540Mbps If a mix of SD and HD signals are passed through the channel select HD Bootload Button This button can be used to reset a channel to factory settings Refer to the section Factory Default Values on page 3 4 for details In the unlikely event of a complete card failure this button is also used for factory service The Bootload process is further described in the section Bootload Button on page 6 2 DEA 8205 User Manual Iss 06 Control and Monitoring Features This section describes the DEA 8205 LEDs PWR LED OK ERROR LED Channel A HD LED SD LED Channel A Rate Selection OK ERROR LED Channel B HD LED SD LED Channel B Rate Selection 4 Bootload Button SW1 Figure 3 2 DEA 8205 Card edge Controls Status and Selection LEDs on the DEA 8205 The front edge of the DEA 8205 has LED indicators for the power video input status and communication activity Basic LED displays and descriptions are provided in Table 3 1 Table 3 1 LEDs on the DEA 8205 Display and Description When lit green this LED indicates that the card is functioning normal and that no anomalies have been detected The following conditions must be satisfied a valid
5. Ea Ooo gt Ross Video Limited DEA 8205 Dual MD SDI Equalizing Amplifier User Manual zl s openhear Live Production Technology DEA 8205 e Dual MD SDI Equalizing Amplifier User Manual Copyright Patents Notice Trademarks Ross Part Number 8205DR 004 06 Release Date March 16 2010 Printed in Canada The information contained in this manual is subject to change without notice or obligation O 2010 Ross Video Limited All rights reserved Contents of this publication may not be reproduced in any form without the written permission of Ross Video Limited Reproduction or reverse engineering of copyrighted software is prohibited This product is protected by the following US Patents 4 205 346 5 115 314 5 280 346 5 561 404 7 034 886 7 508 455 This product is protected by the following Canadian Patents 2039277 1237518 1127289 Other patents pending The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as commitment by Ross Video Limited Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual ROSS is a registered trademark of Ross Video Limited openfear is a trademark of Ross Video Limited Ross ROSS ROSS are registered trademarks of Ross Video Limited e DashBoard Contro
6. alling the RM 8300 B in a DFR 8310 digital distribution frame DEA 8205 User Manual Iss 06 Installation 2 3 Card Installation Use the following procedure to install the DEA 8205 in a DFR 8300 series frame 1 Referto the DFR 8300 Series User Manual to ensure that the frame is properly installed according to instructions 2 Ensure the Rear Module is properly installed as outlined in the procedure Installing a Rear Module on page 2 3 Hold the card by the edges and carefully align the card edges with the slots in the frame Fully insert the card into the frame until the rear connection plugs are properly seated on the mid plane and back plane 5 Affix the supplied Rear Module label to the BNC area on the rear module This completes the procedure for installing the DEA 8205 in a DFR 8300 series frame 2 4 Installation DEA 8205 User Manual Iss 06 Cabling for the DEA 8205 This section provides instructions for connecting cables to the installed BNC rear modules on the DFR 8300 series frame backplane Connect the input and output cables according to Figure 2 2 The inputs are internally terminated in 75 ohms It is not necessary to terminate unused outputs SDI In SDI Out A Channel A 2 SDI Out A SDI Out A 4 SDI Out A SDI Out B 6 SDI Out B SDI Out B 8 10 SDI In Channel B SDI Out B Figure 2 2 Cable Connections for the DEA 8205 DEA 8205 User Manual Iss 06 Installation 2 5 2 6 In
7. e within the equipment manual indicates a situation which if not avoided may result in major or minor equipment damage or a situation which could place the equipment in a non compliant operating state ESD Susceptibility This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event p gt gt BB Important Safety Instructions Caution This product is intended to be a component product of the DFR 8300 series frame Refer to the DFR 8300 series frame User Manual for important safety instructions regarding the proper installation and safe operation of the frame as well as its component products gt Warning Certain parts of this equipment namely the power supply area still present a safety hazard with the power switch in the OFF position To avoid electrical shock disconnect all A C power cards from the chassis rear appliance connectors before servicing this area gt Warning Service barriers within this product are intended to protect the operator and service personnel from hazardous voltages For continued safety replace all barriers after any servicing This product contains safety critical parts which if incorrectly replaced may present a risk of fire or electrical shock Components contained with the product s power supplies and power supply area are not intended to be customer serviced and should be returned
8. e locked and are read only Resets all editable parameters to their Factory Defaults Reset default values a The Channel A or B Rate in the Setup menu affects the Slew Rate of the output driver Ensure that the correct standard for your input is selected Alarm Menus Table 4 3 summarizes the Alarm Menu options available in DashBoard for the DEA 8205 Table 4 3 Alarms Tab Items Tab Title Parameters Description The Signal Status field ignores the status Ignore for the specified input Loss of Input A The Signal Status field displays the status aum for the specified input Alarms The Signal Status field ignores the status Ignore for the specified input Loss of Input B The Signal Status field displays the status REM for the specified input 4 4 Menus DEA 8205 User Manual Iss 06 Specifications In This Chapter This chapter provides technical specification details on the DEA 8205 Note that specifications are subject to change without notice The following topic is discussed Technical Specifications DEA 8205 User Manual Iss 06 Specifications 5 1 Technical Specifications This section includes the technical specifications for the DEA 8205 Table 5 1 DEA 8205 Technical Specifications Category Parameter Specification Number of Inputs 2 Data Rates Supported All data rates from 143Mbps to 1 485 Gbps Impedance 75 terminating e g
9. errors OK ERROR When red this LED indicates the absence of an input signal on Channel A When lit this LED indicates the channel is processing an HD input signal rate 1 485Gbps When lit this LED indicates the channel is processing an SD input signal rate 143Mbps 177Mbps 270Mbps 360Mbps or 540Mbps Factory Default Values Any channel can be set back to factory settings where the data rate is set to HD and the alarm is enabled on loss of input Use the following procedure to reset a channel to factory default values 1 Press and hold the Bootload button on the card 2 Press the rate selection button for the selected channel The Signal Status LED flashes green and red for approximately 2 seconds to confirm the reset values This completes the procedure for resetting a channel to factory default values 3 4 User Controls DEA 8205 User Manual Iss 06 Menus In This Chapter This chapter provides a summary of the menus available for the DEA 8205 The following topics are discussed SNMP Monitoring and Control e DashBoard Control System Software DEA 8205 User Manual Iss 06 Menus 4 1 SNMP Monitoring and Control The Network Controller card in the openGear frame provides optional support for remote monitoring and control of your frame and DEA 8205 using SNMP Simple Network Management Protocol which is compatible with many third party monitoring and control tools Refer to your DEA 8205
10. g the DEA 8205 This section outlines how to install a Rear Module in a DFR 8300 series frame The procedure for installing the Rear Module in your openGear frame is the same regardless of the frame or module used However a different module is required depending on the openGear frame you are using Rear Module for the DEA 8205 The following rear modules are required when installing the DEA 8205 DFR 8310 series frames Use the 8310AR 030 Rear Module R1 8205 DFR 8321 series frames Use the 8320AR 030 Rear Module R2 8205 Installing a Rear Module If the rear module is already installed or if you are installing the DEA 8205 in a DFR 8310 BNC frame skip this section Use the following procedure to install the Rear Module in a DFR 8300 series frame 1 Referto the DFR 8300 Series User Manual to ensure that the frame is properly installed according to instructions On the rear of the frame locate the card frame slot As shown in Figure 2 1 seat the bottom of the Rear Module in the seating slot at the base of the frame s back plane Screw Hole 10 104 H G lt G Module Seating Slot Figure 2 1 Rear Module Installation DEA 8205 not shown Align the top hole of the Rear Module with the screw hole on the top edge of the frame back plane Using a Phillips screwdriver and the supplied screw fasten the Rear Module to the frame back plane Do not over tighten This completes the procedure for inst
11. is manual to provide additional user information DEA 8205 User Manual Iss 06 Introduction 1 3 1 4 Introduction DEA 8205 User Manual Iss 06 Installation In This Chapter This chapter provides instructions for installing the rear modules for the DEA 8205 installing the card into the frame and cabling details The following topics are discussed Before You Begin Installing the DEA 8205 e Cabling for the DEA 8205 DEA 8205 User Manual Iss 06 Installation 2 1 Before You Begin Before proceeding with the instructions in this chapter ensure that your DFR 8300 series frame is properly installed according to the instructions in the DFR 8300 Series User Manual Static Discharge Whenever handling the DEA 8205 and other related equipment please observe all static discharge precautions as described in the following note semiconductor devices Avoid handling circuit boards in high static environments such as carpeted areas and when synthetic fiber clothing is worn Always exercise proper grounding precautions when working on circuit boards and related equipment A ESD Susceptibility Static discharge can cause serious damage to sensitive Unpacking Unpack each DEA 8205 you received from the shipping container and ensure that all items are included If any items are missing or damaged contact your sales representative or Ross Video directly 2 2 Installation DEA 8205 User Manual Iss 06 Installin
12. l System is a trademark of Ross Video Limited All other product names and any registered and unregistered trademarks mentioned in this guide are used for identification purposes only and remain the exclusive property of their respective owners Important Regulatory and Safety Notices Before using this product and any associated equipment refer to the Important Safety Instructions listed below to avoid personnel injury and to prevent product damage Products may require specific equipment and or installation procedures to be carried out to satisfy certain regulatory compliance requirements Notices have been included in this publication to call attention to these specific requirements Symbol Meanings This symbol on the equipment refers you to important operating and maintenance servicing instructions within the Product Manual Documentation Failure to heed this information may present a major risk of damage or injury to persons or equipment Warning The symbol with the word Warning within the equipment manual indicates a potentially hazardous situation which if not avoided could result in death or serious injury Caution The symbol with the word Caution within the equipment manual indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Notice The symbol with the word Notic
13. o policy dictates that all repairs to the DEA 8205 are to be conducted only by an authorized Ross Video Limited factory representative Therefore any unauthorized attempt to repair this product by anyone other than an authorized Ross Video Limited factory representative will automatically void the warranty Please contact Ross Video Technical Support for more information In Case of Problems Should any problem arise with your DEA 8205 please contact the Ross Video Technical Support Department Contact information is supplied at the end of this publication A Return Material Authorization number RMA will be issued to you as well as specific shipping instructions should you wish our factory to repair your DEA 8205 If required a temporary replacement frame will be made available at a nominal charge Any shipping costs incurred will be the responsibility of you the customer All products shipped to you from Ross Video Limited will be shipped collect The Ross Video Technical Support Department will continue to provide advice on any product manufactured by Ross Video Limited beyond the warranty period without charge for the life of the equipment DEA 8205 User Manual Iss 06 Service Information 6 3 Contact Us Contact our friendly and professional support representatives for the following e Name and address of your local dealer e Product information and pricing Technical support e Upcoming trade show information
14. on reuse and recycling systems please contact your local or regional waste administration You can also contact Ross Video for more information on the environmental performances of our products Company Address Ross Video Limited ROSS 8 John Street Iroquois Ontario Canada KOE 1K0 General Business Office Fax Technical Support After Hours Emergency E mail Technical Support E mail General Information Website Ross Video Incorporated P O Box 880 Ogdensburg New York USA 13669 0880 1 613 e 652 e 4886 1 613 e 652 e 4425 1 613 e 652 e 4886 1 613 e 349 e 0006 techsupport rossvideo com solutions rossvideo com http www rossvideo com Laess Contents Introduction 1 OV ELVIS X 1 2 lac Xp EM 1 2 Functional Block Diagraim jeter ertet ests re mnie eae 1 2 Documentation Terms 5 ote e oe eerte et Cer came a te ira te Ee D ental 1 3 Installation 2 Before You Begin 5 aoiaonnie ed E DER ER HER RO EHE HIE miei 2 2 Static Discharge 2e ennn r caesi ed diet ice ici deiade er deeds bdo 2 2 Unpackang iioi oven denen up e gre DU EE atts 2 2 Installing the DEA 82095 cesis suences tute pecie eed eclectic dete dt beue ein 2 3 Rear Module for the DEA 8205 5 nionem ine eere liane 2 3 Installing a Rear Module nennen nennen 2 3 Card Installation ih ertet R EE PER ERR ania 2 4 Cabling for the DEA 8205 cii
15. ound to comply with the limits for a Class A Digital device Notice This is a Class A product In domestic environments this product may A cause radio interference in which case the user may have to take adequate measures Maintenance User Serviceable Parts Routine maintenance to this openGear product is not required This product contains no user serviceable parts If the module does not appear to be working properly please contact Technical Support using the numbers listed under the Contact Us section on the last page of this manual All openGear products are covered by a generous 5 year warranty and will be repaired without charge for materials or labor within this period See the Warranty and Repair Policy section in this manual for details Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ross Video encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crossed out wheeled bin symbol invites you to use these systems If you need more information on the collecti
16. r If the power LED is not illuminated verify that the power cable is connected to a power source and that power is available at the power main Confirm that the power supplies are fully seated in their slots If the power LED is still not illuminated replace the power supply with one that is verified to work Re seat the Card in the Frame Eject the card and re insert it in the frame Check Control Settings Refer to the Installation and Operation sections of the manual and verify all user adjustable component settings 5 Input Signal Status Verify that source equipment is operating correctly and that a valid signal is being supplied 6 Output Signal Path Verify that destination equipment is operating correctly and receiving a valid signal 7 Card Exchange Exchanging a suspect card with a card that is known to be working correctly is an efficient method for localizing problems to individual cards Bootload Button In the unlikely event of a complete card failure you may be instructed by a Ross Technical Support specialist to perform a complete software reload on the DEA 8205 To perform this task perform the following steps 1 Eject the card 2 Press and hold the Bootload button while re inserting the card into the frame 3 Release the button The PWR LED will flash GREEN while the card is waiting for a new software load Ifanew software load is not sent to the card within 60 seconds the card will at
17. r new DEA 8205 fits into your overall working environment Equally pleasing is the product quality reliability and functionality Thank you for joining the group of worldwide satisfied Ross Video customers Should you have a question pertaining to the installation or operation of your DEA 8205 please contact us at the numbers listed on the back cover of this manual Our technical support staff is always available for consultation training or service DEA 8205 User Manual Iss 06 Introduction 1 1 Overview The DEA 8205 is a two channel Multi Definition SDI distribution amplifier capable of equalizing all common serial digital signals Support for both standard definition and high definition signals makes the DEA 8205 an extremely versatile SDI distribution amplifier Each ch of cable annel of the DEA 8205 equalizes the incoming SDI signal compensating for up to 300m at 270Mbps and over 120m of cable at 1 485Gbps Both SDI channels provide 4 outputs each Special attention has been taken to ensure the SDI outputs faithfully reproduce the incoming signals with excellent jitter and return loss specifications LED indicators at the front of the card identify the presence of incoming video simplifying system troubleshooting Features The following features make the DEA 8205 the best solution for general SDI equalizing reclocki ng and distribution Two independent channels with 4 outputs each total of 8 outputs Eq
18. s eet emere ariana pai 2 5 User Controls 3 Card OVervIeW sesenta iden etis eveetie ege nece OA 3 2 Control and Monitoring Feat res iriieier eitis bett astro ette e bn ret PE REPE Ren Educ den 3 3 Status and Selection LEDs on the DEA 8205 erre 3 3 Factory Default Valesi saran eter cH pes ete teres hd pene O een ete 3 4 Menus 4 SNMP Monitoring and Control ettet tete re te erba gls bad da tania ca 4 2 DashBoard Control System Software sse 4 3 Status Mens iaia 4 3 Setup MENUS od serras enm ben stus ML aa 4 4 Alarm Mens alia 4 4 Specifications 5 Technical Specifications snini ninaa aiaia iaia 5 2 Service Information 6 Troubleshooting Checklist 2 n erred contido doar eter iter ins i aa n o dada 6 2 Bootload Button uia e d nsi pnr un REIHE RHET ERE HUS 6 2 Warranty and Repair Policy iieri e Ere Deni neue HER usado FC Feel diee educi 6 3 DEA 8205 User Manual Iss 06 Contents i ii e Contents DEA 8205 User Manual Iss 06 Introduction In This Chapter This chapter contains the following sections e Overview Documentation Terms A Word of Thanks Congratulations on choosing an openGear DEA 8205 Dual MD SDI Equalizing Amplifier Your DEA 8205 is part of a full line of Digital Products within the openGear Terminal Equipment family of products backed by Ross Video s experience in engineering and design expertise since 1974 You will be pleased at how easily you
19. stallation DEA 8205 User Manual Iss 06 User Controls In This Chapter This chapter provides a general overview of the user controls available on the DEA 8205 The following topics are discussed e Card Overview Control and Monitoring Features DEA 8205 User Manual Iss 06 User Controls 3 1 Card Overview The DEA 8205 is a dual channel distribution amplifier and will only have components installed into the CHANNEL A and B sections of the card Channel C is not applicable to the DEA 8205 This section provides a general overview of the DEA 8205 components For information on the card edge LEDs refer to the section Control and Monitoring Features on page 3 3 Figure 3 1 DEA 8205 Card edge Components 1 Channel A Rate Selection Button 2 Channel B Rate Selection Button 3 Bootload Button 1 3 2 User Controls Channel A Rate Selection Button Channel A has a rate selection button and corresponding SD and HD LEDs Use the rate selection button and LEDs to set the input signal rate type that Channel A will process Pressing the button cycles between the HD and SD options You can choose between the following signal rate types e HD 1 485Gbps e SD 143 177 270 360 and 540Mbps Ifa mix of SD and HD signals are passed through the channel select HD Channel B Rate Selection Button Channel B has a rate selection button and corresponding SD and HD LEDs Use the rate selection button and LEDs to
20. t 120m of Belden 1694A cable 1 485Gbps e lt 300m of Belden 1694A cable 270Mbps Return Loss gt 15dB to 1 485GHz Number of Outputs 8 Equalization Impedance 75 Return Loss gt 15dB to 1 485GHz Signal Level 800mV 10 DC Offset OV 50mV 700ps Typical 270Mbps e 120ps Typical 1 485 Gbps Total Power Consumption 1 75W Rise amp Fall Time 20 8094 5 2 Specifications DEA 8205 User Manual Iss 06 Service Information In This Chapter This chapter contains the following sections Troubleshooting Checklist e Warranty and Repair Policy DEA 8205 User Manual Iss 06 Service Information 6 1 Troubleshooting Checklist Routine maintenance to this openGear product is not required In the event of problems with your DEA 8205 the following basic troubleshooting checklist may help identify the source of the problem If the frame still does not appear to be working properly after checking all possible causes please contact your openGear products distributor or the Technical Support department at the numbers listed under the Contact Us section 1 Visual Review Performing a quick visual check may reveal many problems such as connectors not properly seated or loose cables Check the nodule the frame and any associated peripheral equipment for signs of trouble 2 Power Check Check the power indicator LED on the distribution frame front panel for the presence of powe
21. tempt to restart with it s last operational software load Software loads can be sent to the DEA 8205 using the MFC 8300 Series Frame Controller Card with Networking or via connection to the openBUS on the rear of the frame 6 2 Service Information DEA 8205 User Manual Iss 06 Warranty and Repair Policy The DEA 8205 is warranted to be free of any defect with respect to performance quality reliability and workmanship for a period of FIVE 5 years from the date of shipment from our factory In the event that your DEA 8205 proves to be defective in any way during this warranty period Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics Should you find that this DEA 8205 has failed after your warranty period has expired we will repair your defective product should suitable replacement components be available You the owner will bear any labor and or part costs incurred in the repair or refurbishment of said equipment beyond the FIVE 5 year warranty period In no event shall Ross Video Limited be liable for direct indirect special incidental or consequential damages including loss of profits incurred by the use of this product Implied warranties are expressly limited to the duration of this warranty This DEA 8205 User Manual provides all pertinent information for the safe installation and operation of your openGear Product Ross Vide
22. tion of card Rear Module CPU Headroom Process power available RAM Available bytes On board processing memory available EE Bank Signal Status Green Indicator OK Storage count All channels are passing a valid signal Red Indicator No Input A B The indicated channel s has no input signal Channel A Status No Signal No signal present Signal Present The input is present Channel B Status DEA 8205 User Manual Iss 06 No Signal No signal present Signal Present The input is present Menus 4 3 Setup Menus Table 4 2 summarizes the Setup Menu options available in DashBoard for the DEA 8205 Table 4 2 Setup Tab Items Tab Title Parameters Description Sets the Channel A rate to HD 1 485Gbps Select this option if a mix of Hien Dee SD and HD signals are passed through the Channel A Rate channel Sets the Channel A rate to SD Supports Std Def the following rates 143Mbps 177Mbps 270Mbps 360Mbps and 540 Mbps Sets the Channel B rate to HD 1 485Gbps Select this option if a mix of SD and HD signals are passed through the High Def Channel B Rate channel Sets the Channel B rate to SD Supports Std Def the following rates 143Mbps 177Mbps 270Mbps 360Mbps and 540 Mbps All configurable menu options are Unlocked editable Edit permission All configurable menu options except this Locked one ar
23. to the factory for repair To reduce the risk of fire replacement fuses must be the same time and rating Only use attachments accessories specified by the manufacturer gt EMC Notices United States of America FCC Part 15 This equipment has been tested and found to comply with the limits for a class A Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense T Notice Changes or modifications to this equipment not expressly approved by Ross Video Limited could void the user s authority to operate this equipment CANADA This Class A digital apparatus complies with Canadian ICES 003 Cet appariel numerique de la classe A est conforme a la norme NMB 003 du Canada EUROPE This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93 68 EEC INTERNATIONAL This equipment has been tested to CISPR 22 1997 along with amendments A1 2000 and A2 2002 and f
24. ualizes all SDI signals from 143 Mbps to 1 485 Gbps Equalizes up to 300m of Belden 1694A cable at 270 Mbps or over 120m of cable at 1 485 Gbps LED indicators for signal presence on each channel Excellent input and output return loss exceeds SMPTE specifications Fits openGear DFR 8300 series frames 5 year transferable warranty Functional Block Diagram This section provides a functional block diagram that outlines the workflow of the DEA 8205 Channel A BNC 1 Channel B BNC 9 1 2 Introduction SDI OUT BNC 2 BNC 3 BNC 4 Equalizer BNC 5 BNC 6 BNC 7 BNC 8 BNC 10 Figure 1 1 DEA 8205 Simplified Block Diagram DEA 8205 User Manual Iss 06 Documentation Terms The following terms are used throughout this guide Frame refers to the DFR 8300 series frame that houses the DEA 8205 e All references to the DFR 8300 series frame also includes all versions of the 10 slot DFR 8310 series frames and 20 slot DFR 8321 series frames and any available options Operator and User both refer to the person who uses the DEA 8205 Board and Card all refer to the DEA 8205 card itself including all components and switches System and Video system refers to the mix of interconnected production and terminal equipment in which the DEA 8205 operates e DashBoard refers to the DashBoard Control System The Operating Tip and Note boxes are used throughout th
Download Pdf Manuals
Related Search