Using Design-Level Scan to Improve Design
Contents
1. built in logic analyzers such as Xilinx s ChipScope 18 and Altera s SignalTap 2 1 They allow real time access to any node on the chip and include the real time ability to change the trigger conditions Unfortunately although the number of signals that can be accessed at any given time is greater than for an external logic analyzer that number is still limited and the signals must be declared up front before the design is run through the place and route tools Modification to the signals being viewed or to the size of the data capture buffer often requires a time consuming full recompilation of the user design In addition these tools provide no controllability of the user circuit While these tools may be useful for speed testing portions of a larger circuit they are limited in their ability to provide full functional verification of the user design Another common method for debugging FPGA based designs is configura tion readback which enables users to view the state of their design Readback is provided by a number of FPGA vendors such as Xilinx 5 9 and Lucent An example of the steps required to use readback in obtaining all of the state information for Xilinx XC4K devices is provided in 8 Once the readback data is obtained 12 describes how it can be used for debugging in a combined sim ulation hardware execution environment with JHDL 3 11 The advantages of readback are that it theoretically provides complete ob servab2. in Table 1 The LUT count is the number of 4 LUTs contained in the design and the logic element LE count shows the number of basic logic blocks which consist of a single 4 input LUT carry logic and a FF LE counts are useful for showing the true overhead of scan for if the FF in a particular LE is being used but the corresponding 4 LUT is empty that 4 LUT can be used for some of the scan logic without increasing the number of LEs in the design As can be seen in the table both cnt and cordic have roughly the same number of 4 LUTs as they do FFs in the original design thus adding a scan mux to each FF as well as adding the other scan logic effectively doubles the number of 4 LUTs in the designs In addition since most of the LEs in their original designs used up both the FF and the LUT little scan logic could be placed into partially filled LEs so the LE growth for these two designs is roughly the same as the LUT growth Contrast this with mult where the design area is dominated mostly by pipeline and skew registers Thus while the LUT count increased by a factor of 3 23 when instrumented for scan much of the scan logic could be placed in LEs where only the FF was being used so the LE count only increased by a factor of 1 38 The other four designs in the table have the additional cost of instrumenting LUT RAMs and BlockRAMs for scan Figenray BF can place much of its scan logic into partially filled LEs so the LE ratio is signific
3. 4 2 Supplementing Bitstream Modification for Controllability Xilinx FPGAs provide the ability to externally modify the state of their LUT RAMs and BlockRAMs through configuration bitstream modification however the state of the FFs cannot be modified externally Thus one option to provide full controllability of Xilinx FPGAs is to use bitstream modification techniques to control the state of the LUT RAMs and BlockRAMs and to use scan to control just the FFs The area overhead for this method consists of the cost of instrumenting the FFs for scan and a minimal amount of extra logic required to disable all other memories to preserve their state during scan 4 3 Best Case Results Table 2 shows the results of supplementing Xilinx s built in observability and controllability features with variations of full scan The left section provides the overhead required if the designer is only interested in obtaining complete observability of the circuit The overhead is in the form of shadow registers as discussed in Section 4 1 which fix the readback limitations in Virtex BlockRAMs Since only Low power BF and CDI use BlockRAMs they are the only designs affected by the extra logic The middle section shows the overhead required if the designer only desires full controllability of the circuit In this case only the FFs are instrumented for scan while the the state of the embedded RAMs are controlled via bitstream Table 2 Best Case Results for Xilinx De
4. Using Design Level Scan to Improve Design Observability and Controllability for Functional Verification of FPGAs Timothy Wheeler Paul Graham Brent Nelson and Brad Hutchings Department of Electrical and Computer Engineering Brigham Young University Provo UT 84602 wheelert grahamp nelson hutch ee byu edu 1 Introduction With time to market being a chief concern for many hardware designers short ening the debug and validation time for FPGA based designs is critical Software simulation is a common approach to validating hardware designs since it provides complete observability and controllability of the design Unfortunately software simulation is extremely slow and can take hours or days to reach some of the more interesting points in a system s execution thus lengthening the design s validation time Another debug approach is to perform design validation on the existing FPGA hardware itself Direct hardware execution is thousands of times faster than software simulation and the reconfigurability of FGPAs allows design mod ifications to be reprogrammed directly onto the FPGA To be the most effective hardware execution should provide the same level of observability and control lability as a software simulator to enable designers to quickly locate and remove bugs from the design Observability refers to the ability to access all internal state of the circuit similar to the ability of a software debugger to view the val ues of v
5. antly lower than the LUT ratio Low power BF has relatively few FFs so the large number of LUT RAMs and the high cost of instrumenting BlockRAMs give it most of its 66 increase in LE area CDI has many FFs so the FFs and high cost of instrumenting BlockRAMs contribute to most of its 101 LE overhead Lastly Superquant has a high number of both FFs and LUT RAMs so it has a high overhead of 129 3 2 Scan Overhead in FPGAs vs VLSI This section has shown the costs for implementing full scan in FPGA systems is much greater than the 5 30 overheads for VLSI mentioned earlier in this section So why does scan cost so much more in FPGAs than it does in VLSI The answer lies in the granularity of the devices used for implementing scan logic transistor logic costs much less than FPGA LUT logic 7 For example 15 claims that a D flip flop instrumented for scan is only 10 larger in area In an FPGA design however instrumenting a FF for scan effectively doubles its size since the FF and the scan mux are each half of an LE The size may even triple or quadruple by using additional LUTs for the clock enable and set reset scan logic In addition using an entire 4 LUT for the scan mux costs at least 167 transistors 4 whereas the same logic could be implemented in VLSI for about 16 transistors 4 Supplementing Existing Observability and Controllability We have proposed full scan as a method for providing complete observability and controllabi
6. ariables etc Controllability is the ability to modify the run time state of the circuit similar to changing the values of program variables in a software de bugger This latter ability is important because it allows the designer to interact with the design and to change execution flows and infer the root causes of circuit errors much more quickly These capabilities should be provided automatically without having to generate new configuration bitstreams every time a designer chooses to view different signals Unfortunately current FPGA systems and software provide very limited ob servability and controllability for user designs Two common classes of debug techniques are ad hoc and structured methods 16 Examples of ad hoc methods include some forms of self test such as signature analysis 13 as well as routing internal signals to package pads where they can be accessed by a logic analyzer The advantages of these approaches are that they have little impact on the area and speed of the circuit and they allow the circuit to run at full speed during debug However these approaches are painful to use since they require a great deal of user intervention to implement and current packaging technologies make it difficult to probe the debug pins In addition they provide limited or no ob servability into the complete state of the user circuit and no controllability at all Some FPGA vendors try to overcome these limitations by providing their own
7. bility into the user design at all times without recompilation Such a mechanism would help create a debugging environment similar to a software debugger with full observability of the circuit state and the ability to modify circuit state Design level scan is a structured technique that has been investigated at BYU as a means of providing such a capability It is implemented with user circuitry in a manner similar to the way flip flop scan chains are employed for VLSI testing 16 The rest of this paper explores the use of scan to overcome the limitations of the debug methods described above to provide complete observability and controllability for functional verification of FPGA based designs 2 Design Level Scan Implementation Design level scan involves wiring up the memory elements such as flip flops and embedded RAMs in such a way so as to have the state bits contained in these elements exit the circuit serially through a ScanOut pin whenever the ScanEnable control signal is asserted New state data for the FPGA concurrently enters the circuit serially on the ScanIn pin When ScanEnable is deasserted the circuit returns to normal operation Design level scan is different from normal VLSI scan in that its purpose is to obtain or modify the circuit state in order to validate the circuit logic whereas VLSI scan is used to find defects in the silicon after the logic has already been verified extensively in software The benefits of scan are ma
8. erarchical cell and adding scan logic to each flip flop and embedded RAM as described previously Finally an address generator is added as needed for controlling the memories Once the design is instrumented an EDIF netlist is generated and run through the FPGA vendor s back end tools 2 3 FPGA System Level Issues The AND gate shown in Figure 1 is to disable the set reset input to the FF during scan to prevent the FPGA state from being inadvertently modified while scan is taking place This same principle applies to the entire FPGA system so that reads and writes to external memories are not inadvertently affected by scan Writes to external memories can be disabled during scan by tri stating the I O pins of the write enables and connecting them to weak pull ups write enables are active low In addition reads and writes to external memories that have begun but have not yet completed when scan first begins must be handled An easy solution is to buffer the data being read so that it can be used after scan and to buffer the data being written to ensure the correct state is still written to the memories 3 The Costs of Design Level Scan This section discusses the costs of instrumenting user circuits with scan chains Some costs include the extra I O pins used for the ScanIn ScanOut ScanEnable and ScanMode control signals mentioned in Section 2 as well as storage of the scan bitstream when operating in scan mode The main concern to a d
9. esigner however is the circuit area and speed overhead of scan Full scan in VLSI has been reported to require 5 to 30 area overheads 6 10 15 As will be seen shortly the area and overhead of full scan in FPGAs is much greater than this In addition we found that adding scan logic on average reduces the speed of the circuit by 20 Table 1 Full Scan Costs of User Designs Original With Full Scan 3 1 Scan Costs for Sample Designs Consider the scan overheads of several JHDL designs as shown in Table 1 The first three designs are basic JHDL library modules and include a 4 bit up counter a 16 bit by 16 bit fully pipelined array multiplier for which only the upper 16 bits of the product are used and a 16 bit fully pipelined rotational CORDIC unit The other four circuits are large designs done at BYU and consist of Figen ray BF which is a heavily pipelined sonar beamformer that does matched field processing Low power BF 14 which consists of a 1024 point FFT unit and an acoustic beamformer but is unpipelined due to power constraints CDI 17 an ATR unit which performs histogramming and peak finding and Superquant which performs adaptive image quantization to optimally segment images for target recognition The beamformers have significant datapaths including mul tipliers and CORDICs the other two large designs are control intensive Both the original design sizes and their sizes when instrumented with full scan are shown
10. g m 1 LUTs for the address generator and logo m n 1 LUTs for the muxes and OR gate to the RAM for a total overhead of 3 x logo m n 2 LUTs If there are multiple RAMs in the circuit the address generator logic is shared by all of the RAMs so each additional RAM costs only logo m n 1 LUTs to instrument Instrumenting Fully Synchronous Embedded RAMs Another type of RAM to be instrumented for scan is the fully synchronous RAM such as the dual ported Block SelectRAM found in the Xilinx Virtex library Since both the reads and writes are synchronous if the read and write addresses are ever the same during a given clock cycle the data at that location will be overwritten before it is read Thus the approach for scan is to inhibit writing to the RAM during the first cycle of scan to allow the first bit of data to exit the RAM After this writes occur one address behind the reads during scan so as to not overwrite unread data Reading and writing to different addresses on the same cycle re quires the BlockRAM to be multi ported if the BlockRAM is single ported it is simply replaced with its multi ported counterpart at the time of scan instrumen tation In addition if the width of the data ports on the BlockRAM is greater than one bit serial to parallel and parallel to serial converters can be placed at the inputs and outputs to cause the RAM to receive and produce one bit per cycle in the scan chain Also since the contents of a Bl
11. how the primitive memory elements in the Xil inx XC4000 and Virtex libraries are instrumented for scan Similar techniques can be applied to other FPGA vendor libraries Instrumenting Flip Flops FPGA flip flops FFs can be inserted into a scan chain by simply attaching a multiplexor mux before the data input of the FF and logic gates in front of the enables and set pins as shown in Figure 1 D ScanIn ScanEnable ScanOut ScanEnable Clk En ScanEnable Set Clk Fig 1 Instrumenting a Flip Flop for Scan The ScanIn signal in the figure is the ScanOut from the previous memory in the scan chain and the ScanOut signal becomes the ScanIn for the next memory in the scan chain Thus when ScanEnable is asserted the memories in the circuit 1 Once the state of the memory elements is known the values for any combinational portions of the circuit are easy to infer form a shift register when ScanEnable is deasserted the circuit resumes normal operation While ScanEnable is asserted the FF must be enabled and allow its state bit to be shifted out The two extra gates in front of the clock enable and set pins in this example serve this purpose The worst case area overhead for a scannable FF is 300 to add the mux and two logic gates but this price is rarely paid In many instances clock enables sets and resets in a design are either tied to a constant voltage or shared by multiple FFs In the former case the two gates in F
12. igure 1 are not required in the latter case the gates can be shared by multiple FFs Also sometimes the LUT in front of a FF is empty or has unused inputs and can thus be used for either the mux or one of the gates Instrumenting ARSW RAMs Inserting asynchronously read synchronously written ARSW RAMs into scan chains is a bit more complicated than FFs Examples of ARSW RAMs include the synchronous LUT RAMs in the Xilinx XC4000 and Virtex libraries A RAM has multiple internal values to scan out so it is wired up in such a way so as to operate like a FIFO when ScanEnable is asserted It outputs its contents one bit per cycle while upstream ScanJn val ues are concurrently scanned in at one bit per cycle Similar to the FF shown in Figure 1 the data input to the RAM is connected to a mux and the write enable is connected to an OR gate so that scan data is written to the RAM each clock cycle The address input to the RAM is also connected to a mux which selects the output of an address generator whenever ScanEnable is asserted The address generator is basically an up counter that continuously cycles through all of the RAM addresses It starts at an address of zero during the first cycle of scanning out so that the RAM bits are retrieved in a predictable order The address generator must also ensure that the RAM contents are scanned back in at their correct addresses The overhead required to instrument an m bit deep by n bit wide RAM is 2 x log
13. ility of circuit state and it comes for free from the designer s viewpoint when provided as a built in feature of the FPGA However readback has sev eral downsides First readback bitstreams can be extremely large and unwieldy with only a small percentage of the bitstream being useful for obtaining circuit state For example in a Xilinx Virtex V1000 FPGA the bitstream contains over six million bits only 9 of which represents the device s flip flop and memory state the rest is configuration data Second it is often difficult to obtain the information telling how the vendor s software tools mapped the logic to LUTs in order to locate the state values of interest from the readback bitstream Third in some cases not all FPGA state is accessible via readback Fourth performing a readback sometimes alters the state of the FPGA The output registers of Vir tex BlockRAMs are an example of these last two points Fifth for many FPGA families no readback support is provided at all so a different mechanism must be devised to observe the FPGA s internal state Finally we are unaware of any readback implementations that provide any controllability While the above methods are useful for obtaining observability into the cir cuit s state none of them provide any kind of controllability Some FPGAs do provide limited controllability in the form of configuration bitstream modifi cation Bitstream modification in Xilinx can be done directly usi
14. lity for functional verification of FPGA based designs Full scan is often necessary for providing this capability since many FPGA vendors such as Altera and Cypress have neither built in observability nor controllability features However many FPGAs such as those produced by Xilinx Lucent and Atmel are equipped with limited capability to read or modify the state of a circuit Readback and configuration bitstream modification are examples of such capabilities in Xilinx XC4000 and Virtex FPGAs Variations of scan instrumentation can be applied at a fraction of the cost of full scan to supplement these existing features to provide complete observability and controllability of the user circuit This section will show how scan can supplement readback and bitstream modification on Xilinx XC4000 and Virtex FPGAs to provide complete observability and controllability of user designs at a lower cost than full scan 4 1 Supplementing Readback for Observability The built in Virtex readback capability essentially provides complete observ ability The problem is that doing a readback corrupts the circuit s BlockRAM output registers To fix this shadow registers can be added to the circuit to capture the output registers of the BlockRAMs and preserve their state for use immediately after readback This eliminates the need for full scan for observ ability Thus full observability via readback can be achieved for very low cost as will be shown later
15. ng JBits or indirectly by modifying the NCD or XDL files that were created after place and route and then running them through bitgen to generate a new configura tion bitstream When loaded into the FPGA a modified bitstream will initialize the circuit to the specified state This allows the user to test corner cases or to return the circuit to a known state just before a point of failure without the tedious process of determining a series of inputs that will bring the circuit to the desired state The main disadvantages with bitstream modification are that most FPGA vendors provide no CAD support for doing this the vendors do not document the structure of the files that would need to be modified to accomplish this and not all FPGA state can be configured in this manner For example in Xilinx Virtex FPGAs the memories can be configured this way but the flip flops cannot be The methods outlined above while useful in many instances are analagous to using print statements to debug software For example the vendor supplied embedded logic analyzers allow the designer to specify up front which state vari ables to view but changes to this usually require a recompilation of the circuit In addition to providing only limited circuit observability none of the methods provide full controllability and most of them do not provide any controllability features at all What is desired is a mechanism which provides full observability and controlla
16. ny First an FPGA does not require any special capabilities to implement design level scan it can be added to any user design on any FPGA Second the amount of data scanned out of the circuit is much smaller and easier to manipulate than for readback bitstreams since scan bit streams contain only the desired circuit state information Third determining the positions of signal values in the scan bitstream is straightforward since it is easy to determine the order in which the memory elements are arranged in the scan chain Fourth the state of the entire circuit can be retrieved by scan whereas this is not always the case for ad hoc and readback methods Fifth due to the reprogrammable nature of FPGAs the scan chain can be removed from the design after verification thus eliminating the overhead of the scan logic Sixth scan allows the state of the circuit to be set to known values for full circuit controllability Lastly methods like scan can be instrumented systematically and are not design specific so the instrumentation processes can be automated The biggest downside to scan is the large area and speed penalty it causes which will be discussed in greater depth in Section 3 Fortunately the FPGA can be configured without scan after the design has been validated so the overhead is only temporary 2 1 Instrumenting Design Primitives When implementing scan only memory elements are inserted into the scan chain This section explains
17. ockRAM s output regis ters cannot be reloaded shadow registers must be used to capture their contents during scan Instrumenting BlockRAMs for scan is very expensive depending on the configuration of the BlockRAM it costs between 80 150 additional LUTs and 20 80 additional FFs per BlockRAM 2 2 Instrumenting The Design Hierarchy Numerous methods can be used to actually instrument a design with scan A few methods include making modifications to a placed and routed design an EDIF netlist or a circuit database prior to netlisting in the original CAD tool The latter option is the approach of choice within the JHDL design environment since it is relatively simple to implement and can easily be automated In this approach the user design is placed inside a design wrapper that adds the wires for controlling the scan chain ScanEnable ScanIn and ScanOut and connects these and the user wires to I O pins on the FPGA In addition a ScanMode wire is also added if BlockRAMs are present in the circuit The behavior for scanning the data out of a BlockRAM is slightly different than the behavior for scanning data back in ScanMode thus indicates whether we are scanning data in or out of the circuit The instrumentation tool then traverses the circuit hierarchy in a depth first fashion visiting all design submodules and inserting all primitive memory elements into the scan chain This is done by adding the four scan signals as ports to each hi
18. page 97 Prentice Hall PTR Upper Saddle River NJ 1999 A DeHon Reconfigurable Architectures for General Purpose Computing PhD thesis Massachusetts Institute of Technology September 1996 P Graham B Hutchings and B Nelson Improving the fpga design process through determining and applying logical to physical design mappings Technical Report CCL 2000 GHN 1 Brigham Young University Provo UT April 2000 W Holfich Using the XC4000 readback capability Application Note XAPP 015 Xilinx XC4000 San Jose CA 1994 S L Hurst VLSI Testing Digital and Mixed Analogue Digital Techniques chap ter 5 page 218 Number 9 in IEE Circuits Devices and Systems Series Institution of Electrical Engineers London 1998 B Hutchings P Bellows J Hawkins S Hemmert B Nelson and M Rytting A cad suite for high performance fpga design In K L Pocek and J M Arnold editors Proceedings of the IEEE Workshop on FPGAs for Custom Computing Machines page n a Napa CA April 1999 IEEE Computer Society IEEE B L Hutchings and B E Nelson Unifying simulation and execution in a design environment for fpga systems EEE Transactions on VLSI Systems to appear A D F M Abramovici M A Breuer Digital Systems Testing and Testable Design chapter 10 page 421 Computer Science Press New York NY 1990 S Scalera M Falco and B Nelson A reconfigurable computing architecture for microsensors In K L Pocek and J M Arnold edito
19. rs Proceedings of the IEEE Symposium on Field Programmable Custom Computing Machines page TBA Napa April 2000 IEEE Computer Society IEEE Computer Society Press M J S Smith Application Specific Integrated Circuits chapter 14 page 764 Addison Wesley Reading Mass 1997 T W Williams and K P Parker Design for testability a survey IEEE Trans actions on Computers C 31 1 2 15 January 1982 M Wirthlin S Morrison P Graham and B Bray Improving the performance and efficiency of an adaptive amplification operation using configurable hardware In K L Pocek and J M Arnold editors Proceedings of the IEEE Symposium on Field Programmable Custom Computing Machines page TBA Napa April 2000 IEEE Computer Society IEEE Computer Society Press Xilinx San Jose CA ChipScope Software and ILA Cores User Manual v 1 1 edition June 2000
20. s are used to supplement readback and configuration bitstream modification for Xilinx XC4000 and Virtex designs the overhead is reduced to 60 Although the costs in either case are still high they may be justified if the designer can take advantage of fast hardware execution rather than be forced to use software simulation to validate the design thus reducing its overall time to market In addition design level scan costs are temporary since the scan logic can be removed for the final production design References 10 11 12 13 14 15 16 17 18 Altera Corporation San Jose CA SignalTap User s Guide 1999 10 revision 2 edition November 1999 Altera Corporation San Jose CA SignalTap Embedded Logic Analyzer Megafunc tion Data Sheet ver 1 01 edition January 2000 P Bellows and B L Hutchings JHDL an HDL for reconfigurable systems In J M Arnold and K L Pocek editors Proceedings of IEEE Workshop on FPGAs for Custom Computing Machines pages 175 184 Napa CA Apr 1998 V Betz J Rose and A Marquardt Architecture and CAD for Deep Submicron FPGAs chapter Appendix B page 216 The Kluwer International Series in Engi neering and Computer Science Kluwer Academic Publishers Boston 1999 C Carmichael VIRTEX configuration and readback Application Note XAPP 138 Xilinx San Jose CA 1999 A L Crouch Design for Test for Digital IC s and Embedded Core Systems chap ter 3
21. signs Full Observability Full Controllability modification as described in Section 4 2 This approach is particularly useful for designs that either have relatively few FFs or that were paying a huge price to instrument their RAMs with full scan such as Low power BF CDI and Su perquant However the state of the other designs in the table consist mostly of FFs so for them this approach results in about the same circuitry as instru menting the design with full scan Finally the right section of Table 2 shows the cost of supplementing exist ing Xilinx debug features with a combination of the readback shadow registers and scanning only the FFs to provide complete observability and controllability of user designs It shows a 60 LE overhead as opposed to the 84 overhead associated with full scan Although this is certainly an improvement it shows that since FPGA vendors currently do not provide full observability and con trollability features on their FPGAs the cost of obtaining such capabilities for debug is very high 5 Conclusions None of the currently available methods for debugging FPGA based circuits provide the full ability to view and modify the circuit state This work has shown how full scan can be used to overcome their limitations to provide complete observability and controllability of user designs It comes at a high price though with full scan costing an additional 84 in area overhead on average When scan technique
Download Pdf Manuals
Related Search