CAL ETM2432 DIGITAL TIMER
Contents
1. Self extinguishing plastics A While cleaning the device solvents thinner benzine acid etc or corrosive materials must not be used Dimensions 77mm Depth OUT1 OUT2 HOUR MIN 35mm fo7 DIGITAL TIMER For removing mounting clamps 60mm 5mm Push the flush mounting clamp in direction 1 as shown in the figure below Then pull out the GE clamp in direction 2 ETM2432 Flush mounting 2 ee clamp Panel BEEESEREREEE 2 Rubber meedeel Panel cut out beds A Yok 4 a 71 5mm Note 1 Panel thickness should mien ovogars E gt be maximum 7mm CLC Uae 2 Ifthere is not 60mm free reooorKNK NS worsoasammwwm SOLED TVD E space atthe back side of 5 f the device it would be gt S o amp difficult to remove it from i the panel ee WEST Control Solutions The Hyde Business Park Brighton East Sussex BN2 4JU United Kingdom Tel 44 0 1273 606271 Fax 44 8 1273 609990 CAH www west cs com ETM2432 E 01 201411 SET Timer value can be set in Running Mode Parameter values can be set in Programming Mode and newly assigned parameter values can be saved OUT1 OUT2 HOUR MIN OUT1 LED Specifies the output OUT1 After parameter values are changed new values are saved to memory and Running Mode is returned either by pressing 3 button or by waiting 10 f OUT22. button While one of menu parameter is seen sub menu parameter is opened when pressing w button In order to change sub menu parameters value press WA buttons while holding f button down When B button is released all changes will be saved to memory and related sub menu parameter is returned Programming Menu is returned from sub menu parameters by pressing WA buttons at same time In the sub menu all changes will be saved to memory and Running Mode is returned from sub menu if no key is pressed for 10 seconds In programming menu all changes can be saved to memory and Running Mode can be returned from programming menu either by pressing B A buttons at same time or if no key is pressed for 10 seconds Programming Menu Parameter Configuration Diagram lt m SET SET SET a e eee A a r gt 2 gt gt E gt PSE gt C oh a a Vana Time unit Time config lower limit Parameter security code SET hour hour or can be een between Parameter value must be In order to set related parameter to desired value hold button down n n minute ay 0 01 and EuP parameter A EE when display is started to flash use AW buttons value taco reset rd Started Value increases decreases gradually accelerated by pressing if holding W button down for 4 AT buttons continuously ifStr is Str digital inputs seconds while 5 od is 0 ESEE security parameter non Programming Menu invisible PYE 5 Programming
3. LED Specifies the output OUT2 seconds SET HOUR LED Selected time unit is HOUR A Timer is started by pressing amp button for 1 second when 5Er c is selected Except either parameter or time set value changing os oy ix MIN LED Selected LIS NINUTE Menu parameters can be accessed in Programming Mode Parameter set values can be increased Timer set value can be increased in Time Config CAL DIGITAL TIMER ETM2432 ER Mode Timer set value increases gradually accelerated by pressing continuously y Timer and audible warning are stopped by pressing Y button for 1 second when 5E r is selected Except either parameter or time set value changing Menu parameters can be accessed in Programming mode Parameter set values can be decreased Timer set value can be decreased in Time Config Mode Timer set value decreases gradually accelerated by pressing continuously TIME CONFIG MODE SET SET mr T gt v gt se NE gt value aS SET Running Mode switches to Time Config Mode by pressing button Display indicates configuration mode is opened by flashing Desired timer set value can be set by pressing WA buttons After desired timer value set new timer set value is saved to memory and Running Mode is returned either by pressing a button or by waiting 10 seconds Programing Menu is opened and ConF parameter is seen by pressing P and A buttons at same time Switching between menu parameters is done by pressing P
4. Menu start reset gate are enabled Time config upper limit fbtrE is bEre t can be selected between t L of parameter value START STOP buttons are enabled A y and 99 59 parameter can be changed Pno Programming Menu ly bi p Output type parameter can only be seen 9 different output type Time config increase decrease ConF and EEE security parameter can be selected ind E step nonE Programming Menu out 1 oute out3 out3 can be selected between PE ee eni Detailed in page 3 4 1 and 30 parameter can be changed 7 k A Pno Programming Menu Audible Warning Config parameter can only be seen 8 different sound type can be selected f 5d is1 audible warning is enabled WEST Control Solutions The Hyde Business Park Brighton East Sussex BN2 4JU United Kingdom Tel 44 0 1273 606271 www west cs com ff Fax lt 44 0 1273 609900 214 ETM2432 E 01 201411 out 4 out oute out out5 POWER l a start IL UL M Y RESET om AN H ouT2 DISPLAY i 100 0 POWER 2 L amp START l l RESET OUT1 OUT2 JULI L DISPLAY power l ie amp START JON iy Y RESET ouT1 ouT2 DISPLAY 100 0 POWER L amp START JLU NM Y RESET ouT1 ouT2 DISPLAY POWER J L Y RESET ouT1 ouT2 DISPLAY CAL ETM 2432 DIGITAL TIMER OUTPUT TYPES When device is powered If START input is set OUT1 and OUT2 relays are turned on When timer set value
5. Note 3 GATE input can be used for all SEr and Gut types Note 4 When Str t parameter switched from Str I to St r device continue to work with present Gu amp E output setting Timer can be stopped with device front panel STOP button in case of need Note 5 Cases in Note 4 also valid for St r t parameter switched from S amp r c to Str 1 digital RESET input can be used instead of STOP button WEST Control Solutions E The Hyde Business Park Brighton East Sussex BN2 4JU United Kingdom Tel 44 8 1273 606271 www west cs com Fax 44 0 1273 609990 4 4 g ETM2432 E 01 201411
6. Read this document carefully before using this device The guarantee will be expired by device demages if you don t attend to the directions in the user manual Also we don t accept any compensations for personal injury material damage or capital disadvantages CAL ETM2432 DIGITAL TIMER Thank you for choosing CAL ETM2432 digital timer 77 x 35mm sized Dual contact output for timing control External start reset and gate inputs Hours minutes and minutes seconds indications can be selected Scale 0 01 99 59 minutes 0 01 99 59 hours Time increasing and decrement steps can be adjusted Counting in downward direction CAL Start and stop process can be controlled by the front panel 8 different warning tones OUT1 OUT2 HOUR MIN DIGITAL TIMER ETM2432 Upper and lower limits can be adjusted to setpoint value CE marked according to European Norms Re HS Compliant Order Code ETM2432 O00000 1 Supply Voltage 1 230VAC 230V AC QA E 24V AC DC e R 12V AC DC SMi 9 30V DC 7 24V AC CONNECTION DIAGRAM CAL ETM2432 is intended for installation within control panels Make sure that the device is used only for intended purpose The shielding must be grounded on the instrument side During an installation all of the cables that are connected to the device must be free of electrical power The device mustbe protected against inadmissible humidity vibrat
7. hile START input is set OUT1 and OUT2 relays are turned off and timer value is renewed to timer set value If RESET input is reset while START input is set OUT1 and OUT2 relays are turned on and timer starts counting down When device is powered If START input is set OUT1 relay is turned on and timer starts counting down from timer set value When timer set value is expired OUT2 relay is turned on If START input is reset when timer set value is expried timer value is renewed to timer set value If START input is reset while timer counts down OUT1 and OUT2 relays are turned off If RESET input is set while START input is set OUT1 and OUT2 relays are turned off and timer value is renewed to timer set value If RESET input is reset while START input is set OUT1 relay is turned on and timer starts counting down When device is powered If START input is set timer starts counting down When timer set value is expired OUT1 and OUT2 relays are turned on If START input reset when timer set value is expired OUT1 and OUT2 relays are turned off and timer value is renewed to timer set value lf START input is reset while timer counts down timer value is renewed to timer set value If RESET input is set while START input is set timer value is renewed to timer set value If RESET input is reset while START input is set timer value is renewed to timer set value and starts counting down When device is powered If GATE inp
8. ient Storage temperature 50 C 25 70 C Relative Humidity Max humidity 80 for temperatures up to 31 C decreasing linearly to 50 relative humidity at 40 C Protection Class According to EN60529 Front panel IP65 Rear panel IP20 Height Max 2000m A Do not use the device in locations subject to corrosive and flammable gasses ELECTRICAL CHARACTERISTICS Supply 230V AC 10 50 60Hz or 12 24V AC DC 10 50 60Hz or 9 30V DC 7 24V AC 50 60Hz Power Consumption Max 7VA Wiring 2 5mm lik screw terminal Scale Selectable 99 59 min or hour Sensitivity 1 second Time Accuracy 1 Indicator 4 digits 12 5mm 7 segment red LED EMC EN 61326 1 2012 Performance criterion B is satisfied for EN 61000 4 3 Safety Requirements EN 61010 1 2010 Pollution degree 2 overvoltage category I OUTPUT Out 2 Relays 250V AC 8A for resistive load NO and NC control output Life Expectancy for Relay 30 000 000 Switching for no load operation 300 000 switching for 8A resistive load at 250VAC START INPUT Input Type Mechanical contact Minimum 50ms RESET INPUT Input Type Mechanical contact Minimum 50ms GATE INPUT Input Type Mechanical contact Minimum 50ms HOUSING Housing Type Suitable for flush panel mounting according to DIN 43 700 Dimensions W77xH35xD7 1mm Weight Approx 198g After packing Enclosure Materials
9. ions severe soiling Make sure that the operation temperature is not exceeded All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables These cables should not be close to the power cables or components The installation and electrical connections must be carried out by a qualified staff and must be according to the relevant locally applicable regulations GA CAL Controls www west cs com SN XXXXXXXXX GAO CAL Controls www west cs com SN XXXXXXXXX ETM2432 230VAC ETM2432 24 DIGITAL TIMER UL MIHI Ji DIGITAL TIMER DIE IIL IIH a 8 l 804071711703 868 0407 711710 230v AC 10 20 Made In Turkey 24V ACIDC 10 20 Made In Turkey 50 60Hz 50 60Hz 250V AC 8A RESISTIVE LOAD 250V AC 8A RESISTIVE LOAD A w Equipment is protected throughout by Holding screw DOUBLE INSULATION 0 4 0 5Nm NOTE Fuse Note 1 Mains supply cords shall meet the requirements SUPPLY F 100 mA T of IEC 60227 or IEC 60245 250V AC MG 2 In accordance with the safety regulations the 184 253V AC 7 4 Phase z EVE ey regu PERIE 50 60Hz 5VA rs 4 neutrale EN power supply switch shall bring the identification o k Pply the relevant instrument and it should be easily Fuse should be connected accessible by the operator Cable size 1 5mm TECHNICAL SPECIFICATIONS ENVIRONMENTAL CONDITIONS Amb
10. is expired OUT1 and OUT2 relays are turned off If RESET input is set before timer set value expires OUT1 and OUT2 relays are turned off and timer set value is renewed When device is powered If START input is set OUT1 and OUT2 relays are turned on When timer set value is expired OUT1 and OUT2 relays are turned off If RESET input is set before timer set value is expired OUT1 and OUT2 relays are turned off and timer set value is renewed If START input is set before timer set value is expired relays remain turned on and timer set value is renewed and timer starts counting down When device is powered If START input is set timer starts counting down When timer set value is expired OUT1 and OUT2 relays are turned on and timer set value is renewed If START input is set again OUT1 and OUT2 relays are turned off and timer starts counting down if RESET input is set OUT1 and OUT2 relays are turned off and timer stops counting down When device is powered If START input is set OUT1 and OUT2 relays are turned on When timer set value is expired OUT1 and OUT2 relays are turned off timer set value is renewed and timer starts counting down again This process periodically continues If RESET input is set OUT1 and OUT2 relays are turnef off and timer stops counting down When device is powered If START input is set OUT1 and OUT2 relays are turned on When START input is reset timer starts to counting down Whe
11. n timer set value is expired OUT1 and OUT2 relays are turned off and timer set value is renewed If START input is set while timer counts down timer set value is renewed When START input is reset timer starts to counting down If RESET input is set OUT1 and OUT2 relays are turned off and timer stops counting down Lo POWER L J LILT L 3 start 1 Q V RESET out GATE USAGE our l U L LI U Y RESET ouT1 OUT2 DISPLAY POWER A START RESET ouT1 ouT2 DISPLAY When device is powered If START input is set OUT1 and OUT2 relays are turned on and timer starts counting down If START input is reset timer value is renewed to timer set value and timer starts to counting down If START input is set again timer value is renewed to timer set value When timer set value is expired OUT1 and OUT2 relays are turned off and timer value is renewed to timer set value If RESET input is set OUT1 and OUT2 relays are turned off and timer value is renewed to timer set value When device is powered If START input is set OUT1 and OUT2 relays are turned on and timer starts counting down from timer set value When timer set value is expired OUT1 and OUT2 relays are turned off lf START input is reset after an timer set value is expired timer value is renewed to timer set value If START input is reset while timer counts down OUT1 and OUT2 relays are turned off If RESET input is set w
12. ut is set timer set value is seen on display and timer stops counting down If GATE input is reset timer continue where it remains If RESET input is set while GATE input is reset OUT1 and OUT2 relays are turned off and timer value is renewed to timer set value CAH www west cs com WEST Control Solutions The Hyde Business Park Brighton East Sussex BN2 4JU United Kingdom Tel 44 0 1273 606271 Fax 44 o 1273 609990 3 4 ETM2432 E 01 201411 CAL ETM2432 DIGITAL TIMER PARAMETERS CONFIGURATION PARAMETERS Parameter Functional Specification Min Max Unit tines z hr mi 3 t E Device time config 80 01 99 59 ma TIN Strt Device input control parameter Str Stee Str Gut Device output control parameter Gut ovt9 Gut Sond Device audible warning control parameter Sdi Sd amp Sd TIMER CONFIGURATION PARAMETERS tito Time config lower limit define parameter 00 0 99 59 00 EuPL Time config upper limit define parameter 990 82199 59 99 59 indE Time config increase decrease coefficient parameter SECURITY PARAMETERS SCod Security code parameter B 9999 g A 5 Time config security parameter PYES A amp c Menu security parameter PYES Note 1 If S amp r Eselected Str i Control is provided with START RESET GATE inputs Note 2 If Str selected Str Control is provided with device front panel START a STOP buttons
Download Pdf Manuals
Related Search