User Manual Maritime emPower Line Touch Panel
Contents
1. Ep Copy USB Stick Ly Copy to Flash LLL copy tousB gt Import Settings gt Home gt Update image Update gt L Bootloader Ly Home TouchScreen amp Registry Save Registry settings gt disabled p Start Calibration Ep SNTP Settings Ly Home Network gt Settings gt TCP P info gt Fix Settings LM IPAddress poo Gateway gt DNS gt WINS gt Home gt DHCP gt FTP Settings E add new user po gist al users gt Delete a user gt Home Ly Device Name Home Y gt Settings gt Contrast Date Time Password gt Printer Le Page X Settings Network Printer ply Settings Home Information Ly Home Start Batch ile Ly Exit Figure 2 17 Launch overview 2 4 1 2 Normal Mode The program AppStarter exe starts from the internal Flash memory 2 18 SUTRON Maritime emPower Line Touch Panel Installation and Commissioning Press For Setup Main Menu Figure 2 18 Display after startup The following message is issued if the AppStarter exe file does not exist AppStarter not found Figure 2 19 Error message after startup 2 4 1 3 Setup Main Mode If you press the Press For Setup Main Menu button during the startup phase the Setup M2. Connected load 16 8 W Fuse Semiconductor fuse self resetting Protection against Integrated polarity reversal Electrical Data TPM104XiT TPM121XiT TPM151XiT Supply voltage 24 V DC SELV in accordance with DIN EN 61131 Residual ripple 10 maximum Minimum voltage 18V Maximum voltage 30 V Power consumption typi 0 7A 0 7A 1 0A cal at 24 V Power consumption 1 0A 1 0A 1 4A maximum Connected load 16 8 W 16 8 W 24 W Fuse Semiconductor fuse self resetting Protection against Integrated polarity reversal 6 2 S SUTRON Maritime emPower Line Grafik Panel Technical Data Ethernet X5 Ethernet 10 100 Base T USB Corresponds to the Universal serial bus specification Rev 1 1 X9 X10 Host Min 1 5 Mbit s Max 12 Mbit s Max output current 100 mA per output Central Processing Unit Central processing unit RISC CPU PXA320 Clock frequency 806 MHz Memory Flash Internal 1 GByte SDRAM 128 MByte SRAM 1 MByte CompactFlash interface for CompactFlash type and II Connection System Male connector strip Phoenix COMBICON 3 pin Male connector strip Phoenix MINI COMBICON 2 pin RJ45 female connector USB female connector A Environmental Conditions Temperature during operation 0 C to 50 C 32 F t
3. Time Set the date time and time zone Settings Password Password Current Password jJ M Enable Password Figure 2 38 Password 2 25 S SUTRON Installation and Commissioning Maritime emPower Line Touch Panel The password can be activated deactivated or redefined When the password is ac tivated all password protected dialog boxes can only be accessed if the password has been entered successfully This entry is password protected Settings Printer Page Network Settings Print Figure 2 39 Printer Branching to Page Settings and Network Print This entry is password protected Settings Printer Page Settings Page Settings Page Settings Letter O A4 Figure 2 40 Page Settings Select the paper format Letter or A4 Letter is default This entry is automatically stored in the registry Settings Printer Network Print Network Print Network Printer Path Network Server Login Figure 2 41 Network Print Enter the network printer path This entry is automatically stored in the registry Settings Printer Network Print Network Server Login Figure 2 42 Network Server Login 2 26 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning You may perform a network login Enter a user name password and domain This entry is automatically stored in the registry Settings Information SNR 1023456789 Image_Grafikpanel_EP
4. 2 1 N Nameplate a 2 30 Normal operating mode 2 18 O Ordering data 7 1 Overview Launcher hr teer pine Peri beds 2 18 P Pin assignment Ethernet et tee ca Prae deed 4 2 H ROSE M E 3 1 S Safety notes 1 2 SOTVICINQ LE 5 1 Setup Main operating mode 2 19 Standards ttt eerte xir 6 4 Supply voltage 24 V 2 15 Switching Oni cocer kaaa 2 17 Symbols General dtt entere tint 1 1 Specific tems 1 1 T Target group eroi teca ct iere 1 2 Technical data eene 6 1 Touch SCHON PEN 3 1 U Unpacking 5 5 ree e niet dies 2 1 V Version KOY i iet et artt Eia dde 2 30 A 1 S SUTRON Index emPower Line Grafik Panel A 2 S SUTRON S SUTRON
5. of at least 30 mm 1 181 around the device to ensure sufficient air circulation When the operating device is installed horizontally please note that additional sources of heat beneath the operating device may result in heat accumulation Make sure to allow sufficient heat dissipation Comply with the allowable temperature range listed in the technical data for the use of the operating device To ensure the specified degree of protection make sure that the seal rests flat on the mounting surface and the threaded pins of the mounting brackets are uniformly tight ened The device can be easily and quickly mounted from the rear of the device Ideally the device should be installed in switch panels with a plate thickness of approx 1 mm to 6 mm 0 039 to 0 236 1 Insert the device in the mounting cutout from the front H q Figure 2 1 Mounting the device using a mounting bracket 2 1 SUTRON Installation and Commissioning Maritime emPower Line Touch Panel 2 Insert the mounting brackets into the appropriate openings figure 1 and pull the brackets downwards until they lock in place figure 2 3 Fasten the device into position using the threaded pins figure 3 2 2 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 2 2 1 Front Panel Dimensions 158 mm 6 22 210 mm 8 268 Figure 2 2 TPM65XiT 2 3 S SUTRON Installation and Commissioning Maritime emPowe
6. start an application on the usb stick Start HardDisk MyProgram exe Use multiple entries to start several applications Registry Default Destroys the current registry and activates the default registry of the image The change becomes effective on the next de vice reboot StartRepllog On Enables automatic startup of the Repllog exe program in the registry The change becomes effective on the next device re boot StartRepllog Off Disables automatic startup of the Repllog exe program in the registry The change becomes effective on the next device re boot LaunchTouch On The touch variant of the launch will start at devices with key board The change becomes effective on the next device re boot LaunchTouch Off The standard variant for the device will start The change becomes effective on the next device reboot Lock On The buttons Press for Setup Main Menu and Admin are dis abled If the file Admin ini is found on the usb stick the button Admin is enabled Therefore the deactivation of the lock is possible The change becomes effective on the next device reboot Lock Off All buttons enabled The change becomes effective on the next device reboot Mode Development The shell has full functionality The change becomes effective on the next device reboot 2 28 SUTRON Maritime emPower Line Touch Panel Installation and Commissioning Mode
7. 42 001 Network Settings Fix Settings WINS Primary WINS 000 000 000 000 Secondary WINS 000 000 000 000 Figure 2 30 WINS The system deselects DHCP and enters the settings from the IPSetting ini file of the USB stick This file must exist in the root directory of the USB stick If no USB stick is connected the information is read from the registry This entry is password protected Contents of the IPSetting ini file IPCONFIG PrimaryWINS 172 016 042 150 SecondaryWINS 172 016 042 151 ILZ All addresses must be given in the format XXX XXX XXX XXX Numbers smaller than 100 you have to fill up with zeros Example 192 168 42 1 gt 192 168 042 001 Network Settings DHCP DHCP enabled Save registry and restart device to work with new parameters Figure 2 31 DHCP You may enable DHCP service You must save this setting when exiting of by using Save Registry Settings This entry is password protected 2 23 S SUTRON Installation and Commissioning Maritime emPower Line Touch Panel Network Settings FTP Settings Add new user Figure 2 32 Add new user You may enter a new user name You have to assign a password to the user name and to confirm it If at least one user name is added you cannot login to the FTP server as anonymous anymore Network Settings FTP Settings List all users All users are listed within a DOS box Network Settings FTP Settings Delete a user Enter
8. 6 22 x 8 267 x 0 196 Seal Circumferential rubber seal on the rear Mounting cutout H x W in mm Inch 150 x 202 5 905 x 7 952 Mounting depth without About 60 mm connectors 2 362 Degree of protection Front IP65 Rear IP20 Total weight About 1300 g Front Panel and Enclo TPM104XiT TPM121XiT TPM151XiT sure Enclosure Steel sheet galvanized Front panel material Aluminium brushed black anodized Front panel H x W x D in 265 x 328 x 5 10 433 x 285 x 340 x 5 11 220 x 338x400 x 5 13 307 x mm Inch 12 913 x 0 197 13 386 x 0 197 15 748 x 0 197 Seal Circumferential rubber seal on the rear Mounting cutout H x W 238 x 303 259 x 315 312 x 373 in mm Inch 9 370 x 11 929 10 197 x 12 402 12 283 x 14 685 Mounting depth in mm 57 2 244 62 2 44 62 2 44 Inch Degree of protection Front IP65 Rear IP20 Total weight About 2200 g About 2500 g About 3600 g 6 SUTRON 6 5 Technical Data Maritime emPower Line Grafik Panel 6 6 S SUTRON Maritime emPower Line Touch Panel Ordering Data 7 Ordering Data Table 7 1 Accessories Description Part No CompactFlash card 256 MB 81152 255 CompactFlash adaptor for laptops 81166 000 CompactFlash adaptor for PC 81167 000 USB 2 0 stick 1 GB 81152 100 Battery assembled with cable and connector Type CR2450 66779 000 Protective foi
9. 9307_CE5 00_ V1 18 Built Aug 27 2007 14 00 00 Flash Size 16 MB SRAM Size 512 kB PLC VISU RAM 0 460 kB Busclock 49 MHz Click OK to go back to main Figure 2 43 Information The following informations are displayed Serial number Product ID Image version Built version Built date Size of flash Size of SRAM Size of PLC Visu RAM Bus clock speed Start Batchfile The project bat file in the FlashDrv directory starts if available 2 27 S SUTRON Installation and Commissioning Maritime emPower Line Touch Panel IEJ 2 4 1 4 Administration Operating Mode If you press the Admin button during the startup phase the Administration mode of operation starts You can use the Admin ini file to manage the device This file must exist in the root directory of the USB stick This file is used as a dongle to prevent users from changing the device during normal operation Possible contents for the Admin ini file Observe upper and lower case for all entries Explorer Off Deactivates the Explorer in the registry The change becomes effective on the next device reboot Explorer On Activates the Explorer in the registry The change becomes ef fective on the next device reboot Start explorer exe Starts the explorer Start MyProgram exe Starts the application MyProgram exe Initial directory is windows Use the following syntax to
10. Registry SNTP Settings You can enter the address of a time server located in the intranet or Internet The synchronization interval is specified in minutes This entry is password protected Network Settings Network Settings TCP IP Info DHCP Device Name Figure 2 25 Network Settings TCP IP Info MAC 0 7 93 FF FF CE IP 192 168 100 82 Mask 255 255 255 0 Device Name MyName DHCP enabled Gate 000 000 000 000 1 DNS 000 000 000 000 2 DNS 000 000 000 000 1 WINS 000 000 000 000 2 WINS 000 000 000 000 Figure 2 26 TCP IP Info The following informations are displayed MAC address IP address Subnet mask address Device name DHCP status Gateway address 1 DNS address 2 DNS address 1 WINS address 2 WINS address S SUTRON 2 21 Installation and Commissioning Maritime emPower Line Touch Panel Network Settings Fix Settings IP Address IP Address IP Address 000 000 000 000 Subnet Mask 000 000 000 000 Figure 2 27 IP Address The system deselects DHCP and enters the settings from the IPSetting ini file of the USB stick This file must exist in the root directory of the USB stick If no USB stick is connected the information is read from the registry This entry is password protected Contents of the IPSetting ini file IPCONFIG IPAddress 172 016 042 150 SubnetMask 255 255 255 000 All addresses must be given in the format xxx xxx xxx xxx Numbers
11. S SUTRON visualization control communication User Manual Maritime emPower Line Touch Panel Part Number 80860 754 Version 1 Date 2009 12 02 Valid for TPM65XiT 10 3201xxxx TPM104XiT 10 3201xxxx TPM121XiT 10 3201xxxx TPM151XiT 10 3201xxxx visualization control communication Version Date Modifications 1 01 12 2009 First Edition This manual including all illustrations contained herein is copyright protected Use of this manual by any third party in departure from the copyright provision is forbidden No part of this manual may be reproduced trans lated or electronically or photographically archived or altered without the express written consent from S tron electronic GmbH Violations shall be cause for damage liability S tron electronic reserves the right to make any changes that contribute to technical improvement S SUTRON Maritime emPower Line Grafik Panel Overall Table of Contents Overall Table of Contents 1 IiMponant Notes cR 1 1 1 1 gs 1 1 1 1 1 General Symbols reete de teer tree ce ca erred ennemies 1 1 1 1 2 Specific Symbols ssesssssssssseseseeeeeeneeee nennen 1 1 1 2 Safety NOIl6S c eee eee ae eee ne eod pa e end een ace Rae ER us 1 2 13 Intended Se radii ee pena een EO EERER E i en TY ae s E AE Eee SEE at 1 2 1 4 Target Groups etre ee eer teet Aerie nat te rv ERR qua ee 1 2 2 Installation and COMMISSIONINg uou cca eue R
12. Standard The Shell is restricted No task bar and task switch available Desktop contains the launch icon only The change becomes effective on the next device reboot DeviceName MyName Defines the device name of the operating device DeviceName MyName Comment no impact S suTRON B Installation and Commissioning Maritime emPower Line Touch Panel 2 5 Identification The operating device can be identified using the nameplate on the rear of the device www suetron de Tel 49 711 77098 0 1 Typ TP104AT 731030 80850430_113 118 04XX 101 0007920001 M 8 peee ae Un 24 VDC In 0 6 A 2 2 5 200404210133 Figure 2 44 Nameplate example Order number Version key at time of delivery MAC address Voltage and power specification Serial number a FON 2 5 1 Version Key The version key provides information on the version level of various components at time of delivery 80850430 _ 113 118 O4XX 101 Bundle Bootloader Image Application Software Installation Auxiliary Software 2 30 SUTRON Maritime emPower Line Touch Panel Control and Display Elements 3 Control and Display Elements gt gt 3 1 Touch Screen The device is equipped with a resistive 4 wire touch screen You operate the device using this touch screen Poi
13. User Enter Password PS Confirm Password eeu Figure 2 33 Delete a user You may enter the user name you like to delete This entry is password protected Network Settings Device Name Device name Enter Device Name MyDeviceName 9 Figure 2 34 Device Name You can define a device name with up to 14 characters Via a FTP connection you can access the device with the device name instead of the IP address This entry is password protected Settings Date Time Figure 2 35 Settings 2 24 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning Settings Contrast Contrast Brightness Color Depth O 8bpp O 16bpp Figure 2 36 Contrast The operating mode setup main is displayed with default values for contrast and brightness to ensure reading also at faulty values If you change a value you have to confirm this in a dialog If you press Cancel or 5 seconds pass without any action the value is not accepted Depending on the display type different values can be influenced Table 2 2 Display Type Contrast Brightness STN mono X STN color X TFT X Selection of color depth for TFT displays This entry is password protected Settings Date Time Date Time Current Time D 00 A 15 00 00 AM Time Zone GMT 01 00 Amsterdam Berlin Bern Rome EZ Automatically adjust clock for daylight saving Figure 2 37 Date
14. ain mode starts 3 Some settings are password protected The password is Update Copy USB Update Image Update Bootloader Figure 2 20 Update Update Copy USB Stick Copy to Flash Copy to USB Import Settings Figure 2 21 Copy USB Stick Update Copy USB Stick Copy to Flash This function copies the data from the USB stick to the internal flash file system Several projects can be managed in subdirectories below the directory TSvisRT If more than one project is in different subdirectories a choice dialog is displayed Only directories which contain a project file cb are listed The entire TSvisRT directory or the corresponding subdirectory and the AppStarter exe are copied into the target directory of the flash file system Update Copy USB Stick Copy to USB Copies the content of the flash file system to the backup directory of the USB stick This excludes protected system files A log file is also transferred which can be used to restore system settings via the Import Settings item S SUTRON 2 19 Installation and Commissioning Maritime emPower Line Touch Panel Update Copy USB Stick Import Settings An automatically generated log file can be used to restore the system settings If the backup directory of the USB stick contains a corresponding log file these settings can be restored This is possible only when using identical device types Update Update Image If th
15. amsau crime ente ton o ana a 2 1 2 1 Unpacking the Device ss 2 1 2 2 Mounting the Device serenas 2 1 2 2 1 Front Panel Dimensions nissan 2 3 2 2 2 Mounting Cutout sissisotaa iaaa 2 7 2 2 3 Side View Mounting Depth sssssesesseenenee 2 11 2 3 Connecting the Device ss 2 15 2 8 1 Supply Voltage 24 V osrstenie noraen E EN EAE OEE 2 15 2 4 SWICHING Once rete dtc a ree eg eed eus 2 17 2 4 1 Loading Procedure on Windows CE Operating System 2 17 2 4 1 1 IE UnINS IEEE 2 18 2 4 1 2 Normal MOUS 4 deer eri reo ri reef shacshisaasundsttsseeceaattuscaidenasc 2 18 2 4 1 3 Setup Main Mode HU tee irait es 2 19 2 4 1 4 Administration Operating Mode eae 2 28 2 5 Identification e 2 30 2 5 1 Version Key Em ees 2 30 3 Control and Display Elements sen 3 1 3 1 Touch Screens TT 3 1 32 Rey RESE cose street ee malins lib 3 1 cic ee eee ee eee 3 1 4 Iguzigielekig 2Bi c r 4 1 4 1 Standard Interfaces scetur eren rre ener eh es nai 4 1 4 1 1 IC E 4 2 4 1 1 1 tW Cre m 4 2 4 1 1 2 er M A A E 4 2 4 1 1 3 DiagNOSIS Est R 4 2 4 1 2 URIZP CHOSE 4 3 4 1 2 1 Cable e 4 3 4 22 Memory Card iuueni td eei Ee Dr Mined 4 4 4 2 1 Inserting the Memory Card 4 4 4 2 2 E
16. anel 2 10 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 2 2 3 Side View Mounting Depth Figure 2 10 TPM65XiT Mounting Bracket Threaded Pin Mounting Surface Thickness 1 mm to 6 mm Circumferential Seal Front Panel a fon GS SUTRON o Installation and Commissioning Maritime emPower Line Touch Panel 60 mm 2 362 Figure 2 11 TPM104XiT Mounting Bracket Threaded Pin Mounting Surface Thickness 1 mm to 6 mm Circumferential Seal Front Panel a ron 2 12 SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 65 mm 2 559 a AON Figure 2 12 TPM121XiT Mounting Bracket Threaded Pin Mounting Surface Thickness 1 mm to 6 mm Circumferential Seal Front Panel a fon S SUTRON 2 13 Installation and Commissioning Maritime emPower Line Touch Panel 65 mm 2 559 H F CJ CE E D af GO ND Figure 2 13 TPM151XiT Mounting Bracket Threaded Pin Mounting Surface Thickness 1 mm to 6 mm Circumferential Seal Front Panel a fon 2 14 SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 2 3 Connecting the Device 2 3 1 Supply Voltage 24 V The supply voltage is supplied via connector X1 The device has reverse polarity prote
17. be required to introduce appropriate countermea sures and to bear the cost of same 1 4 Target Group All configuration programming installation commissioning operating and mainte nance work in connection with the automation system must be performed by trained personnel only e g qualified electricians electrical engineers etc The configuration and programming personnel must be familiar with the safety con cepts of automation technology The operating personnel must have been trained in handling the controller and be familiar with the operating instructions The installation commissioning and maintenance personnel must have an education which entitles them to work on automation systems 1 2 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 2 Installation and Commissioning gt DD 2 1 Unpacking the Device Unpack all parts carefully and check the contents for any visible damage in transit Also check whether the shipment matches the specifications on your delivery note If you notice damages in transit or discrepancies please contact our sales depart ment immediately 2 2 Mounting the Device The following safety distances to a compass must be kept depending on the display size of the operating device Display lt 7 Display gt 7 Standard compass 0 75 m 29 527 2 2 m 86 614 Steering compass 0 45 m 17 716 1 35 m 53 149 When installing the device leave a gap
18. ction In case of wrong polarity the device will not operate This is a protection class device For safe operation safety extra low voltage SELV in accordance with DIN EN 61131 must be used for the supply voltage Connector in the operating device 3 pin connector Table 2 1 Pin assignment supply voltage Pin Designation Function 1 2 Low Noise Ground 2 OV Supply Voltage 0 V 3 24 VDC Supply Voltage 24 VDC A suitable female connector strip is supplied 3 Cables with finely stranded conductors with a minimum cross section of 0 75 mm 18 AWG and a maximum cross section of 2 5 mm 14 AWG must be used for the supply voltage Hazardous voltages can exist inside electrical installations that can pose a danger to humans Coming in contact with live parts may result in electric shock Use the following procedure to connect the device to the supply voltage 1 Strip approx 30 mm 1 181 off the outer cable sheath and approx 5 mm 0 197 off the wires 5 mm 0 197 SE ME 30 mm 1 181 Figure 2 14 Preparing the cable 2 Fit the wires with wire end ferrules and connect the wires to the connector 2 15 S SUTRON Installation and Commissioning Maritime emPower Line Touch Panel N Figure 2 15 Connecting the female connector strip 3 If shielded connecting cables are used in the supply voltage area the shield should be connected to pin 1 3 Plug the female connector s
19. e image subdirectory on the memory stick contains a nbO file this file is used to perform the image update There must only be one nbO file in this directory In this case the flash registry is always deactivated so that the image is processed with a new default registry Update Update Bootloader If the bootloader subdirectory on the memory stick contains a nbO file this file is used to perform the bootloader update There must only be one nbO file in this di rectory The user is informed that the update has been successfully completed Touch Screen amp Registry Save Registry disabled Start SNTP Calibration Settings Figure 2 22 Touch Screen amp Registry Touch Screen amp Registry Save Registry Settings The entire registry is saved Touch Screen amp Registry Change Display Mode Current Mode wie 9 O gt M LCD Saver O v Figure 2 23 Change Display Mode Set up of display adjustment LCD Saver switches the brightness to the lowest value if no user operation occures for at least one hour This entry is password protected Touch Screen amp Registry Start Calibration The touch calibration is started After the calibration the values are stored automati cally in the registry Registry SNTP Settings 2 20 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning SNTP Settings Server myserver myhost local Figure 2 24
20. e liner from the adhesive pad of the battery 10 Fasten the new battery on the inside of the enclosure 11 Disconnect the connector strip of the supply voltage 12 Place the enclosure back onto the device ONOaA amp D 13 Place the interface plate onto the enclosure if necessary While mounting the enclosure observe that all nibs are fitting into the corresponding notches of the underneath enclosure 14 Carefully tighten the screws of the enclosure and then the screws of the interface plate 5 2 S SUTRON Maritime emPower Line Touch Panel Maintenance and Servicing 15 Plug in the connector strip of the supply voltage Figure 5 1 Screws on the operating device 5 4 2 Battery Disposal 3 To prevent short circuitry in the collection boxes insulate the poles of each battery with insulation tape or put each single battery into a plastic bag You must always return old batteries to a dealer or to a returns depot set up for this purpose by the public waste disposal body or a licensed battery dealer for recycling Only dispose of dead batteries in public or commercial collection boxes The battery is drained when the message Change battery appears on the display of the device G SUTRON o Maintenance and Servicing Maritime emPower Line Touch Panel 5 4 S SUTRON Maritime emPower Line Grafik Panel Technical Data 6 Technical Data Display TPM65XiT Type TFT c
21. jecting the Memory Card 4 4 i S SUTRON Overall Table of Contents Maritime emPower Line Grafik Panel 5 Maintenance and Servicing eee terresorcasdepreresuerececetapaianeenmterarualannonethapinanierenuneeuneble 5 1 5 1 Maintenance Interval nene n enn 5 1 b Front Panels a dee tant meee 5 1 COMEMBIICI M 5 1 5 4 B ttery Option eter ee Ur eee sca 5 1 5 4 1 Changing the Battery ss 5 2 5 4 2 Battery Disposal 5 nonsese cimece sise 5 3 6 Technical cc RR 6 1 7 Ordering D 1 tinc texb dote Un ue prr va ee peus nico cee nena tain 7 1 o Uere A 1 ii S SUTRON Maritime emPower Line Touch Panel Important Notes 1 Important Notes a p adi a gt aaa 1 1 Symbols The symbols in this manual are used to draw your attention on notes and dangers 1 1 1 General Symbols Danger This symbol is used to refer to instructions which if ignored or not carefully followed could result in personal injury Note This symbol indicates application tips or supplementary notes Reference to source of information This symbol refers to detailed sources of information on the current topic 1 1 2 Specific Symbols The following symbols indicate specific dangers which could result in damage to equipment or personal injury or even up to the death of the operator Danger Electric Shock Danger Corrosive Danger Toxic Dange
22. l for touch screen 6 5 Set with 10 protective foils scraper and instructions 81251 065 Protective foil for touch screen 10 4 Set with 10 protective foils scraper and instructions 81251 104 Protective foil for touch screen 12 1 Set with 10 protective foils scraper and instructions 81251 121 Protective foil for touch screen 15 Set with 10 protective foils scraper and instructions 81251 150 7 1 S SUTRON Ordering Data Maritime emPower Line Touch Panel 7 2 S SUTRON emPower Line Grafik Panel A Index A ACCOSSOLIBS nantes same tue x RR Ren 7 1 Administration operating mode 2 28 B Bate iY C M 5 1 Battery disposal 5 3 C Cable Etliernet eer ins mens 4 2 USB c vs 4 3 Changing the battery 5 2 Connecting tette ett etes 2 15 D Dimensions DT a m E M 2 7 Front panel itr eene 2 3 DISPIAY 3 1 F gll X 5 1 Identification casni neidia aisanana aia 2 30 Intended use ssiri neinna eads 1 2 Interface ENEM initier aaa a aeaa 4 2 USB PR A 4 3 L Launcher Overview 2 18 Loading procedure on Windows CE operating sys DOM es ass ue 2 17 M Maintenance 5 1 Maintenance interval 5 1 Memory card 4 4 Mounting
23. nted or sharp objects such as pens or fingernails can lead to irreparable dam ages of the touch screen Exclusively therefore use the fingertips or the aids indi cated in the technical data for the operation To protect the touch screen you can use special protection foils You receive corre sponding protection foils directly from S tron electronic 3 2 Key Reset The reset key is located on the rear of the device You can use this key to restart the device 3 3 Display Danger Toxic If the display is damaged avoid touching swallowing or breathing in the liquids or gases which may leak out Danger Corrosive If the display is damaged avoid touching swallowing or breathing in the liquids or gases which may leak out The operating device is equipped with different displays depending on variant 3 1 S SUTRON Control and Display Elements Maritime emPower Line Touch Panel S SUTRON Maritime emPower Line Grafik Panel Interfaces of the Device 4 Interfaces of the Device The following figures show the TP104XiT exemplarily for all operating devices de scribed in this manual 4 1 Standard Interfaces Un 24 VDC In 0 8 A Les 001 pals SDF mum Y Lx Er X9 gs X10 RES a 8 T 6 5 Figure 4 1 Rear view TPM104XiT Seal Front Panel Nameplate Battery Inf
24. o 122 F Temperature during storage transport 25 C to 70 C 13 F to 158 F Relative air humidity for operation and storage 20 to 85 no condensation Application area Degree of pollution 1 overvoltage category II S SUTRON 6 3 Technical Data Maritime emPower Line Grafik Panel Standards and Guidelines Interference immunity EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 EN 61000 6 2 Emitted interference EN 50011 limit class value A Equipment requirements EN 61131 Storage and transportation EN 61131 part 2 Power supply EN 61131 part 2 Electromagnetic compatibility 2004 108 EG Degree of protection EN 60529 Impact load shocks EN 60068 part 2 27 Sinusoidal vibrations EN 60068 part 2 6 Corrosion protection IEC 60068 UD This is a class A device This device may cause radio interference in residential ar eas In this case the user may be required to introduce appropriate countermea sures and to bear the cost of same Approvals ABS BV CE DNV GL LR 6 4 S SUTRON Maritime emPower Line Grafik Panel Technical Data Front Panel and Enclo sure TPM65XiT Enclosure Steel sheet galvanized Front panel material Aluminium brushed anodized natural finish Front panel H x W x D in mm Inch 158 x 210 x 5
25. ode 100 MBit s and proper connection with 100BASE T hub 2 Yellow On ACT Sending receiving ether net data telegram 4 2 SUTRON Maritime emPower Line Grafik Panel Interfaces of the Device 4 1 2 USB X9 X10 Two host interfaces are available on the operating device Using the USB interfaces while normal operating mode is not permitted for maritime applications For maritime applications the use of the USB interfaces is allowed for servicing op erations only Using input devices not suitable for industrial use e g keyboard mouse may de crease safety of operation This includes input devices inteded for home and office use 4 1 2 1 Cable For the specification of a suitable cable please refer to the Universal Serial Bus Specification Rev 1 1 The maximum cable length for the cable used is 2 5 m 8 202 feet 4 3 S SUTRON Interfaces of the Device Maritime emPower Line Grafik Panel 4 2 Memory Card You can insert a CompactFlash card on the side of your operating device The Com pactFlash card allows you to exchange projects between the PC and the operating device You can recognize the rear side of a CompactFlash card by the notches on each side of the card Figure 4 3 Rear view of the memory card 4 2 1 Inserting the Memory Card When you insert the card from the rear side of the operating device make sure the fron
26. olor Resolution pixels 640 x 480 Colors 65535 Reading angle vertical 120 140 horizontal Half life backlighting 70 000 h Brightness in cd m 400 Display area H x W in mm Inch 99 x 132 3 897 x 5 196 Display TPM104XiT TPM121XiT TPM151XiT Type TFT color TFT color TFT color Resolution pixels 640 x 480 800 x 600 1024 x 768 Colors 65535 Reading angle vertical 110 140 110 140 135 160 horizontal Contrast setting Half life backlighting 50 000 h Brightness in cd m 350 300 480 Display area H x W in 158 x 211 185 x 246 228 x 304 mm Inch 6 22 x 8 307 7 283 x 9 685 8 976 x 11 969 Touch Screen Type Analog resistive 4 wire technology Activation force 15 g Standard With R8 HS60 silicon rubber Durability No damages or malfunctions after 3 million keystrokes as the following Keystroke element R8 HS40 silicon rubber Keystroke load 150 g Keystroke frequency 3 Hz Electrical Data TPM65XiT Supply voltage 24 V DC SELV in accordance with DIN EN 61131 Residual ripple 10 96 maximum Minimum voltage 18V SUTRON 6 1 Technical Data Maritime emPower Line Grafik Panel Electrical Data Forts TPM65XiT Maximum voltage 30 V Power consumption typi 0 7 A cal at 24 V Power consumption 1 0A maximum
27. ormation Threaded Bolt For Protective Grounding Connector X1 Supply Voltage Reset Key Female Connector X9 X10 USB Host Type A Female Connector X5 Ethernet on the Side of the Operating Device 10 Compact Flash Inserted on the Side on the Operating Device OMAN OA BR N S SUTRON 4 1 Interfaces of the Device Maritime emPower Line Grafik Panel 4 1 1 Ethernet X5 A 10 100 Base T Ethernet interface is located on the side of the operating device 4 1 1 1 Pin Assignment Connector in the operating device RJ45 female connector Table 4 1 Assignment of the Ethernet interface Pin Designation Function 1 Tx Transmitted Data Positive Polarity 2 Tx Transmitted Data Negative Polarity 3 Rx Received Data Positive Polarity 4 n c Not Connected 5 n c Not Connected 6 Rx Received Data Negative Polarity 7 n c Not Connected 8 n c Not Connected 4 1 1 2 Cable 3 A twisted pair cable of the category 5 CAT 5 type must be used The maximum ca ble length is 100 m 328 084 feet E See the IEEE 802 3 standard for further information 4 1 1 3 Diagnosis Ethernet diagnostics LEDs are located at the side of the operating device 1 2 Vo Figure 4 2 Arrangement of the ethernet diagnostics LEDs Table 4 2 Ethernet diagnostics LEDs No Color State Designation Function 1 Green On LNK 100 Operation in m
28. r Explosive Danger Fire Danger Infrared Light Danger Electrostatic Charge 1 1 S SUTRON Important Notes Maritime emPower Line Touch Panel 1 2 Safety Notes Read this manual carefully before using the operating device Keep this manual in a place where it is always accessible to all users Proper transportation handling and storage placement and installation of this product are prerequisites for its subsequent flawless and safe operation This user manual contains the most important information for the safe operation of the device The user manual in particular the safety notes must be observed by all person nel working with the device Observe the accident prevention rules and regulations that apply to the operating site Installation and operation must only be carried out by qualified and trained per sonnel 1 3 Intended Use The device is designed for use in maritime areas The device is state of the art and has been built to the latest standard safety re quirements However dangerous situations or damage to the machine itself or other property can arise from the use of this device The device fulfills the requirements of the EMC directives and harmonized Euro pean standards Any modifications to the system can influence the EMC behav ior This is a class A device This device may cause radio interference in residential ar eas In this case the user may
29. r Line Touch Panel 249 0 mm 9 803 oN 328 0 mm 12 913 Figure 2 3 TPM104XiT G SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 270 0 mm 10 63 Figure 2 4 TPM121XiT N 340 0 mm 13 386 S SUTRON 2 5 Installation and Commissioning Maritime emPower Line Touch Panel 329 0 mm 12 953 400 0 mm 15 748 Figure 2 5 TPM151XiT A 2 SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 158 mm 6 22 2 2 2 Mounting Cutout 150 mm 5 905 202 mm 7 952 49MM EET p 210 mm 8 267 Figure 2 6 TPM65XiT A Mounting Cutout B Front Panel 6 SUTRON 2 7 Maritime emPower Line Touch Panel Installation and Commissioning 303 0 mm 11 929 328 0 mm 12 913 0p2 8 ww o zez 08 6 uuu O 6pz Figure 2 7 TPM104XiT A Mounting Cutout B Front Panel SUTRON 6 2 8 Maritime emPower Line Touch Panel Installation and Commissioning 270 0 mm 10 63 243 5 mm 9 587 315 0 mm 12 402 340 0 mm 13 386 Figure 2 8 TPM121XiT A Mounting Cutout B Front Panel 2 9 S SUTRON Installation and Commissioning Maritime emPower Line Touch Panel 329 0 mm 12 953 302 0 mm 11 89 400 0 mm 15 748 Le 373 0 mm 14 685 Figure 2 9 TPM151XiT A Mounting Cutout B Front P
30. smaller than 100 you have to fill up with zeros Example 192 168 42 1 gt 192 168 042 001 Network Settings Fix Settings Gateway Change Default Gateway 000 000 000 000 Figure 2 28 Gateway The system deselects DHCP and enters the settings from the IPSetting ini file of the USB stick This file must exist in the root directory of the USB stick If no USB stick is connected the information is read from the registry This entry is password protected Contents of the IPSetting ini file IPCONFIG Gateway 172 016 042 150 All addresses must be given in the format xxx xxx xxx xxx Numbers smaller than 100 you have to fill up with zeros Example 192 168 42 1 gt 192 168 042 001 Network Settings Fix Settings DNS Primary DNS 000 000 000 000 Secondary DNS 000 000 000 000 Figure 2 29 DNS 2 22 SUTRON Maritime emPower Line Touch Panel Installation and Commissioning The system deselects DHCP and enters the settings from the IPSetting ini file of the USB stick This file must exist in the root directory of the USB stick If no USB stick is connected the information is read from the registry This entry is password protected Contents of the IPSetting ini file IPCONFIG PrimaryDNS 172 016 042 150 SecondaryDNS 172 016 042 151 Ss All addresses must be given in the format xxx xxx xxx xxx Numbers smaller than 100 you have to fill up with zeros Example 192 168 42 1 gt 192 168 0
31. t side of the card is visible Insert the card until it snaps into place o gt Figure 4 4 Inserting the memory card 4 2 2 Ejecting the Memory Card To remove the card press the ejection button on the operating device o gt Figure 4 5 Ejecting the memory card 4 4 S SUTRON Maritime emPower Line Touch Panel Maintenance and Servicing 5 Maintenance and Servicing 5 1 Maintenance Interval The following maintenance intervals are recommended for this operating device Table 5 1 Maintenance work Interval Changing the Battery 4 Years 5 2 Front Panel Only use a damp cloth to remove any dirt from the front panel 5 3 Fuse The semiconductor fuse cannot be replaced A semiconductor fuse is used to protect the device Once the fuse has been tripped the device must be disconnected from the supply voltage to allow the semiconductor fuse to regenerate At an ambient temperature of 20 C 68 F the regeneration takes approximately 20 seconds The higher the ambient temperature the longer the regeneration takes 5 4 Battery Option The built in battery supplies the real time clock The minimum battery life is 5 years even under unfavorable operating conditions We recommend to change the battery approximately every 4 years as part of the reg ular maintenance work A prepared battery including connector can be obtained di rectly from S tron electronic Carry out the following
32. to check the battery status 1 Press the Servicetool button on your operating device 2 Open Systeminfo by double clicking double tapping the appropriate icon 3 Select the Battery tab You can display the following statuses Battery OK Battery is ready for operation No battery found Battery is empty or there is no battery at all 5 1 S SUTRON Maintenance and Servicing Maritime emPower Line Touch Panel PbPbbb 5 4 1 Changing the Battery Batteries must only be changed by authorized and trained experts For changing the battery you may only use replacement batteries of S tron electronic Electrostatic discharge can damage electronic components Observe the ESD pro tective measures Do not throw lithium batteries into fire do not heat to 100 C or higher and do not recharge Danger Explosive Do not open lithium batteries Danger Toxic To ensure the the time is preserved it is possible to change the battery under oper ating voltage Observe the safety notes Disconnect the connector strip of the supply voltage Remove the screws see figure on the rear panel of the device Remove the interface plate if necessary foursquare Lift off the enclosure Plug in the connector strip of the supply voltage Disconnect the connector strip of the battery an remove the dead battery Clean the inside of the enclosure to remove rests of glue if necessary Plug in the cable for the new battery 9 Remove th
33. trip onto connector X1 Figure 2 16 Female connector strip is plugged on 4 Secure the female connector strip in place with a screw type locking to prevent it from slipping out A separate conductor must always be provided for the protective grounding at the threaded bolt The conductor must have a minimum cross section of 1 5 mm 16 AWG and must be kept as short as possible 2 16 S SUTRON Maritime emPower Line Touch Panel Installation and Commissioning 2 4 Switching On The Windows CE operating system is installed on the operating device Running on the operating system is the visualization runtime software TSvisRT 2 4 1 Loading Procedure on Windows CE Operating System The program allows you to use the buttons to make changes to the configuration The operating device has 3 operating modes Normal no button is pressed Setup Main Button Press For Setup Main Menu was pressed Administration Admin button was pressed 2 17 S SUTRON Installation and Commissioning Maritime emPower Line Touch Panel 2 4 1 1 Launch Overview Start Normal Ly Admin gt Setup Main be a Update
Download Pdf Manuals
Related Search